FOR THE MOST IMPORTANT PEOPLE
IN THE WORLD
DOUBLE SIDED SWING DOWN BED RAIL
Model: 2250
09/12/2013_EV
...........................................................................
Regalo International, LLC.
3200 Corporate Center Drive, Suite 100
Burnsville, MN 55306-9803, USA
Toll Free: 866-272-5274
Made in China
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST :
1. Bed Rail Mesh Wall (X2)
2. Left Upper Support Bar (X2)
3. Right Upper Support Bar (X2)
4. Left Bottom Support Bar (X2)
5. Right Bottom Support Bar (X2)
6. Corner Hinge Assembly (X2)
1
1
2
3
2
5
6
4
3
4
6
5
2
Download from Www.Somanuals.com. All Manuals Search And Download.
BED RAIL ASSEMBLY AND SET UP
Step 1 : Remove bed rails from packaging and set all parts out in front of you.
Step 2 :
Assemble one side of the double bed rail completely before
assembling the second side. Join a Left Upper Support Bar to a
Left Lower Support Bar. Make sure the spring pin fits securely
into its opposing hole so that the two parts can not pull
(Diagram A1)
appart.
(Diagram A2)
: Repeat Step 2 directions to assemble the right side.
Step 3
(Diagram A1)
(Diagram A2)
(Diagram B1)
Step 4 : With the left and right sides assembled, join them together.
NOTE : Make sure that the spring pins are secured into the opposing holes so that
the assembly cannot pull apart.
(Diagram B1)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Frame assembly should look like the image below. (Diagram B2)
(Diagram B2)
Step 5 : To install the mesh wall on the frame assembly, slide the mesh wall over the frame
until it reaches the other end and zip it shut to complete the installation. (Diagram C1)
NOTE : If the zipper does not close securely, make the necessary adjustments to ensure
proper closure. DO NOT use the bed rail without securely zipping the mesh wall
properly!
(Diagram C1)
Step 6: Repeat steps 1-5 to assemble the second side of the double bed rail.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 7: With the walls of the bed rail completely assembled, you will now connect
them to the corner hinges and anchor straps. (Diagram D1)
(Diagram D1)
Spring button
Spring
button
(Diagram D2)
(Diagram D3)
Step 8: Insert one side of the wall frame into one of the corner hinges. Press in the
metal spring button to fully insert the tube into the hole in the plastic sleeve.
(Diagram D2)
The spring button should line up with the access hole in the plastic sleeve
on the hinge. The spring button will rebound and lock the tube in place.
(Diagram D3)
Repeat Step 7 with the other 3 corner hinges to complete the assembly.
Note:
Each set of corner hinges is permanently connected by an anchoring
strap. On one side of each set, the strap is adjustable. The adjustable
sides should be mounted to the same side wall assembly.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The finished assembly should look like the image below
(Diagram D4)
(Diagram D4)
MOUNTING THE BED RAILS TO THE BED
The next steps may require the assistance of an additional person
Note :
Remove the mattress from the bed you will be mounting the double sided
bed rail to. Then, place the assembly atop the box spring or mattress support
structure so that it is positioned in the orientation of its final placement.
(Diagram E1)
Step 1:
In order to adjust the bed rail to fit your specific bed properly, you may need to
release the strap locking buckles located on the under side of the plastic
hinges. The anchoring straps should not be twisted. If twisted, the anchoring
straps may not tighten properly.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
(Diagram E1)
Step 2:
Once the bed rail is placed properly, place the mattress back atop of
the box spring or mattress support sandwiching the flat metal bars
of the corner hinges and the anchoring straps between the box
spring and the mattress.
(Diagram E2)
(Diagram E2)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING : In order for the bed rail mesh wall to be firmly held against the side of
the mattress you MUST properly tighten the anchoring straps. Please follow the
directions below very carefully.
Step 3 : Tighten the straps to bring the bed rail into it’s proper position. To tighten
the straps, first release the strap locks on the under side of the Corner Hinges.
Pull the straps towards you until all the excess slack has been pulled out from
under the mattress and both sides of the bed rail are firmly pressed against the sides of the
mattress.
(Diagram E3)
CAUTION: When using this bed rail on a foam mattress with little or no internal structure,
make sure not to over tighten the mounting straps. If over-tightened, the mattress will
likely fold or buckle in the middle and this will cause the bed rail to not provide your child
with the highest level of safety. Make slight adjustments to find the best level of tightness
on your mattress.
(Diagram E3)
Step 4 : If the strap does not pull through smoothly, the strap may be twisted under
the mattress. Correct this before continuing with the installation.
Once you have taken the slack out of the straps, give one final pull on the strap end,
hold it, and lock the locking tab on the locking buckle by pushing up on the thumb
tab. Use the same procedure for each side to properly secure the bed rail.
IMPORTANT : After locking both buckles, check to make sure that the mesh walls of
the crib rail are firmly up against the side of the mattress. There should be NO GAPS.
If the mesh walls are not firmly against the side of the mattress, check to make sure
the locking buckle is functioning properly and that the strap is not twisted beneath
the mattress. Once this has been checked and corrected, unlock the buckle and pull
on the end of the strap to tightly lock the buckle again.
NOTE : Store the excess anchoring strap material by tucking it under the mattress.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION OF SWING DOWN FEATURE
(Diagram F)
Step 1: With the bed rail side in the ‘up’ position, locate the locking tab on each of
the hinges. (Diagram F) A close up view of the hinge is shown in (Diagram G1).
Step 2: Once the locking tabs have been located, flip the tab up to expose the open
side of the lock. (Diagram G2) This will allow the upper part of the bed rail to move
freely.
NOTE : Be sure to continue to hold the upper part of the bed rail so that it does not
fall on its own!
(Diagram G1)
(Diagram G2)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3 : With both locking tabs turned to the ‘open’ position, hold the upper part of
the bed rail firmly and swing it down.(Diagram H1) The bed rail should now be in
the ‘down’ position. (Diagram H2)
NOTE : To return the bed rail to the ‘up’ position, reverse the previous instructions.
IMPORTANT: Make sure that the bed rail is in the ‘up’ position nad the locking tabs are
securely closed before leaving a child alone in the bed.
(Diagram H1)
(Diagram H2)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
Periodically check the bed rail for signs of damage, wear and/or for missing
components.
Do not use if any part is missing, worn or damaged.
Check the bed rail regularly to make sure all hardware and mountings are
tight and secure.
Do not use abrasive cleaners or bleach when cleaning.
Proper cleaning of bed rail can be done by sponging it with warm water and
mild detergent.
90 Days Limited Warranty:
If, during the first 90 days after consumer purchase of this item, under reasonable
and non-commerical use and conditions of maintenance, it fails while owned by
the original purchaser because of the quality of materials or workmanship of finish
and assembly, Regalo International LLC will replace or repair it at Regalo’s option,
Proof of purchase required.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
COPYRIGHT 2013 Regalo International, LLC.
3200 Corporate Center Drive, Suite 100
Burnsville, MN 55306-9803, USA
Toll Free: 866-272-5274
Made in China
09/12/2013_EV
Download from Www.Somanuals.com. All Manuals Search And Download.
|