M37906T-PRB
Pod Probe for 7906 Group MCUs
User's Manual
Rev.1.00
September 1, 2003
REJ10J0288-0100Z
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
The M37906T-PRB is a pod probe for the 7906 Group of Renesas 16-bit microcomputers. The
M37906T-PRB is used by connecting to the PC4701 emulator main unit and the M37900T2-RPD-E
emulation pod main unit (option).
This manual mainly explains specifications and how to set up the M37906T-PRB. For detail
information about the emulator main unit, emulation pod main unit, and emulator debugger, refer to
each user's manual.
Emulator main unit
Emulation pod main unit : M37900T2-RPD-E User's Manual
Emulator debugger : M3T-PD79 User's Manual
: PC4701 User's Manual
To check the components of this product, refer to "2.2 Package Components" (page 17) in this
manual. If there is any question or doubt about this product, contact your local distributor.
To use the product properly
Precautions for Safety:
• Both in this User's Manual and on the product itself, several icons are used to insure
proper handling of this product and also to prevent injuries to you or other persons,
or damage to your properties.
• The icons' graphic images and meanings are given in "Chapter 1 Precautions for
Safety". Be sure to read this chapter before using the product.
( 3 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Chapter 1. Precautions for Safety ...........................................................................................7
1.1 Safety Symbols and Meanings ..............................................................................8
Warning for Installation ...................................................................................9
Warning for Use Environment.........................................................................9
Caution to Be Taken for Modifying This Product ...........................................9
Cautions to Be Taken for This Product ...........................................................9
Notes on Target System .................................................................................10
Note on Reset Input from the Target System ................................................10
Notes on Stack Area ......................................................................................10
Note on MCU Files ........................................................................................10
Notes on EMEM Dialog ................................................................................11
Note on Boot Mode........................................................................................11
Note on Breaks Used with Internal Resources ..............................................11
Note on Debug Monitor Area ........................................................................11
Note on Interface with the Target System .....................................................12
Notes on Service-Life of the MCU's Internal Flash ROM ............................12
Note on Debug Commands during STP/WIT Instruction .............................12
Notes on Disabling Watchdog Function ........................................................12
Note on Real-Time RAM Monitor ................................................................12
Note on Coverage Measurement....................................................................12
Note on Differences between Actual MCU and Emulator ............................13
Chapter 2. Preparation ..........................................................................................................15
2.1 Terminology ........................................................................................................16
2.2 Package Components ..........................................................................................17
2.3 Other Tool Products Required for Development ................................................17
2.4 System Configuration..........................................................................................18
Chapter 3. Setting Up ...........................................................................................................19
3.1 Switch Settings ....................................................................................................20
3.2 A-D Conversion Bypass Capacitor .....................................................................21
3.3 Connecting the Emulation Pod Main Unit ..........................................................22
3.4 Connecting the Target System ............................................................................24
( 4 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Specifications ......................................................................................................27
4.1 Specifications ......................................................................................................28
4.2 Electrical Characteristics.....................................................................................28
4.3 Connection Diagram ...........................................................................................29
4.4 External Dimensions of Pod Probe .....................................................................30
Chapter 5. Troubleshooting ..................................................................................................31
5.1 When the Emulator Debugger Does Not Operate ...............................................32
(1) Errors Occur When Operating the Emulator Debugger
(When the target system is connected)....................................32
(2) Errors Occur When Operating the Emulator Debugger
(When the target system is not connected) .............................33
5.2 Operation Differs from That of Actual MCUs....................................................33
(1) Initializing the Internal Resources of MCU at Power-on.........................33
(2) Oscillator Circuits......................................................................................33
(3) Flash ROM 2KB Expansion Area..............................................................33
(4) When the A-D Conversion Values are Different from Expected Values ....33
(5) When the D-A Conversion Values are Different from Expected Values ....33
Chapter 6. Maintenance and Warranty .................................................................................35
6.1 Maintenance ........................................................................................................36
6.2 Warranty..............................................................................................................36
6.3 Repair Provisions ................................................................................................36
6.4 How to Request for Repair..................................................................................37
( 5 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
( 6 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Precautions for Safety
This chapter describes precautions for using this product safely and properly. For precautions for the emulator main unit,
the emulation pod main unit and the emulator debugger, refer to each user's manual included with your product.
1.1 Safety Symbols and Meanings ..................................................................................................... 8
WARNING
Warning for Installation ............................................................................................... 9
Warning for Use Environment ..................................................................................... 9
CAUTION
Caution to Be Taken for Modifying This Product ....................................................... 9
Cautions to Be Taken for This Product........................................................................ 9
IMPORTANT
Notes on Target System ............................................................................................. 10
Note on Reset Input from the Target System............................................................. 10
Notes on Stack Area................................................................................................... 10
Note on MCU Files .................................................................................................... 10
Notes on EMEM Dialog ............................................................................................ 11
Note on Boot Mode.................................................................................................... 11
Note on Breaks Used with Internal Resources .......................................................... 11
Note on Debug Monitor Area .................................................................................... 11
Note on Interface with the Target System ................................................................. 12
Notes on Service-Life of the MCU's Internal Flash ROM ........................................ 12
Note on Debug Commands during STP/WIT Instruction.......................................... 12
Notes on Disabling Watchdog Function .................................................................... 12
Note on Real-Time RAM Monitor ............................................................................ 12
Note on Coverage Measurement................................................................................ 12
Note on Differences between Actual MCU and Emulator ........................................ 13
( 7 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1. Precautions for Safety
In both the user's manual and on the product itself, several icons are used to insure proper handling
of this product and also to prevent injuries to you or other persons, or damage to your properties.
This chapter describes the precautions which should be taken in order to use this product safely and
properly. Be sure to read this chapter before using this product.
1.1 Safety Symbols and Meanings
If the requirements shown in the "WARNING"
sentences are ignored, the equipment may
cause serious personal injury or death.
WARNING
If the requirements shown in the "CAUTION"
sentences are ignored, the equipment may
malfunction.
CAUTION
It means important information on using this
product.
IMPORTANT
In addition to the three above, the following are also used as appropriate.
means WARNING or CAUTION.
Example:
CAUTION AGAINST AN ELECTRIC SHOCK
means PROHIBITION.
Example:
DISASSEMBLY PROHIBITED
means A FORCIBLE ACTION.
Example:
UNPLUG THE POWER CABLE FROM THE RECEPTACLE.
The following pages describe the symbols "WARNING", "CAUTION", and "IMPORTANT".
( 8 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Warning for Installation:
• Do not set this product in water or areas of high humidity. Spilling water or some other liquid into
the main unit can cause an unrepairable damage.
Warning for Use Environment:
• This equipment is to be used in an environment with a maximum ambient temperature of 35°C. Care
should be taken that this temperature is not exceeded.
CAUTION
Caution to Be Taken for Modifying This Product:
• Do not disassemble or modify this product. Disassembling or modifying this product can cause
damage. Disassembling and modifying the product will void your warranty.
Cautions to Be Taken for This Product:
• Use caution when handling the main unit. Be careful not to apply a mechanical shock.
• Do not touch the connector pins of the emulator main unit and the target MCU connector pins
directly. Static electricity may damage the internal circuits.
• Do not pull the pod probe by the flexible cable (FLX120-RPD) for connecting to the emulator main
unit or the flexible cable (FLX100) for connecting the target system. The cable may cause a break.
• Flexible cable FLX120-RPD and FLX100 are different from earlier models. The slits make them
more flexible. However, excessive flexing or force may break conductors.
• Do not use inch-size screws for this equipment. The screws used in this equipment are all ISO
(meter-size) type screws. When replacing screws, use same type screws as equipped before.
( 9 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
Notes on Target System:
• The Vcc pin of emulator is connected to the target system to observe the voltage of the target system.
Therefore the emulator cannot supply the power to the target system. Design your system so that
the target system is powered separately.
• The voltage of the target system should be within the range of the MCU specification and suit to
the emulator MCUs as shown below:
- For 5.0V version MCUs: +4.5 to +5.5V
• Do not change the voltage of the target system after turning on the power.
• Before powering on your emulator system, check that the host machine, the PC4701, M37900T2-
RPD-E, the converter board and target system are all connected correctly. Next, turn on the power
to each equipment following the procedure below.
(1) Turn ON/OFF the target system and the PC4701 as simultaneously as possible.
(2) When the PC4701 and emulator debugger M3T-PD79 start up, check the target status LEDs
on the emulator main unit's front panel to see if this product is ready to operate.
• Is the power supplied?
• Is the clock supplied?
Check that target status LED (POWER) is ON.
Check that target status LED (CLOCK) is ON.
Note on Reset Input from the Target System:
• The reset input from the target system is accepted only while a user program is being executed (only
while the RUN status LED on the PC4701's front panel is lit).
Notes on Stack Area:
• With this product, a maximum 26 bytes of the user stack is consumed as work area.
• If the user stack does not have enough area, do not use areas which cannot be used as stack (SFR
area, RAM area which stores data, or ROM area) as work area. Using areas like this is a cause of
user program crashes and destabilized emulator control. Therefore, ensure the +26 byte maximum
capacity used by the user program as the user stack area.
Note on MCU Files:
• When starting up the emulator debugger M3T-PD79, select the MCU file corresponding to the
MCU which is going to be debugged by Init dialog (MCU files are included with the emulator
debugger M3T-PD79).
MCU
MCU file name
M37906F8.MCU
M37906M4.MCU
M37906F8
M37906M4
( 10 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
Notes on EMEM Dialog:
• When setting the EMEM dialog box of emulator debugger M3T-PD79, pay attention to the
following:
(1) Processor Mode
Specify a processor mode for the target MCU to be debugged. With 7906 Group MCUs, only
the single-chip mode is specifiable. If the MD0 pin setting is not "L" level, emulator debugger
M3T-PD79 outputs an error message. In such a case, check the pin settings on the target
system.
(2) Emem Address
Allocate the 1MB emulation memory that is included in the emulation pod. For the 7906
Group, it is not necessary to set this because this group operates only in the single-chip mode.
(3) ROM Address
Disable the allocated emulation memory against writes by the user program. For the 7906
Group, it is not necessary to set this because this group operates only in the single-chip mode.
(4) DMA Address
In this dialog box, set a transfer area when using the MCU's DMA function, and executing 1-
bus transfer between emulation memory and the target system. For the 7906 Group, do not set
such areas because this group does not have the DMA function.
(5) 8-bit bus mode Address
When accessing external data buses in 8-bit width using the chip select wait controller when
BYTE pin = Low, set this address for the relevant area. For the 7906 Group, it is not necessary
to set this because this group operates only in the single-chip mode.
(6) Map Address
Set external or internal for the allocated emulation memory area. For the 7906 Group, it is not
necessary to set this because this group operates only in the single-chip mode.
Note on Boot Mode:
• It is not possible to debug the MCUs in the boot mode using this emulator system.
(The MD1 pin of the MCU is fixed to the "L" level.)
Note on Breaks Used with Internal Resources:
• H/W breaks cannot be used with internal resources (SFR, internal RAM and internal flash ROM)
when using emulator PC4701L.
Note on Debug Monitor Area:
• The debug monitor area is fixed to the "FF" bank. It cannot be set to other banks.
( 11 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
Note on Interface with the Target System:
• The pin that connects to the target system is pulled-up by the emulation pod probe using local
resistors. For the difference in electric characteristics between the actual MCU and the emulator,
see "Chapter 4. Specifications" (page 27).
Pullup resistors of Init4* pin
To avoid high impedance, this pin is pulled-up with a 510kΩ resistor. These pullup resistors
cannot be removed.
Notes on Service-Life of the MCU's Internal Flash ROM:
• With emulators of the 7900 Series, programs are downloaded to the MCU's flash ROM when
debugging in the single-chip mode and memory expansion mode. Because the number of write/
erase cycles of this ROM is limited, the ROM must be replaced when at the end of its service-life.
• If the following errors occur frequently during program download, replace the MCU board
(M37906T-PRBM).
Flash memory erase error ERROR (11508)
Flash memory verify error ERROR (11509)
To purchase the MCU board (M37906T-PRBM) for replacement, contact your local distributor.
Note on Debug Commands during STP/WIT Instruction:
• When a debug command (e.g. referencing memory) is issued during execution of STP/WIT
instruction, STP/WIT instruction is canceled. And when the debug program has completed, the
following instructions are executed.
Note on Disabling Watchdog Function:
• When disabling the watchdog timer during programming, do not open the DUMP window, the
memory window and the RAM monitor window in the area which contains the special function
select register 2 (address 64h). When displaying address 64h, it is not possible to disable the timer.
Note on Real-Time RAM Monitor:
• Word access from an odd-numbered address cannot be correctly displayed. This restriction of the
MCU - emulator interface cannot be avoided. Use the optional function of assembler AS79 to
arrange word data to start from an even-numbered address.
Note on Coverage Measurement:
• The trace data output from the MCU is operational code address information only. Make note of
the fact that, in coverage measurement, the calculation result is unpredictable because the operand
address is not tagged.
( 12 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
Note on Differences between Actual MCU and Emulator:
• Operations of the emulator differs from those of mask MCUs as listed below.
(1) Initial values of internal resource data (such as a part of SFR, and RAM) at power-on
(2) Oscillator circuit
Make note of the fact that in the oscillator circuit where a resonator is connected between the
XIN and XOUT pins, oscillation does not occur because a flexible cable, buffer IC and other
devices are used between the emulator MCU and the target system.
( 13 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
( 14 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Preparation
This chapter describes the package components, the system configuration and the preparation for using this product for the
first time.
2.1 Terminology ............................................................................................................................... 16
2.2 Package Components.................................................................................................................. 17
2.3 Other Tool Products Required for Development........................................................................ 17
2.4 System Configuration ................................................................................................................. 18
( 15 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2. Preparation
2.1 Terminology
Some specific words used in this user's manual are defined as follows:
Emulator system
This means an emulator system built around the PC4701 emulator. The PC4701 emulator system is
configured with an emulator main unit, emulation pod, pod probe, host machine and emulator
debugger.
Emulator main unit (Hereafter PC4701)
This means a generic name for emulators for 8 and 16-bit MCUs. For details on specific models of
Emulation pod
This means the common part which matches to the 7900 Series MCUs. The emulation pod is used
by connecting the pod probe.
Pod probe
This means the pod probe for 7906 Group M37906T-PRB (this product).
Host machine
This means a personal computer used to control the emulator and emulation pod.
Emulator debugger
This means a software tool M3T-PD79 to control the emulator from the host machine through an
interface.
Firmware
Program that analyzes contents of communication with the emulator debugger and controls the
emulator hardware. This program is installed in the EEPROM. This program is downloadable from
the emulator debugger to upgrade the firmware or to support other MCUs.
Emulator MCU
This means the special package MCU for the emulator mounted on the emulation pod.
Target system
This means a user's application system using the microcomputer to be debugged.
*
In this user's manual, this symbol is used to show active LOW. (e.g. RESET*: Reset signal)
( 16 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 Package Components
This product consists of the following items. When unpacking, check to see if your product package
contains all of these items.
Package components
Item
Quantity
M37906T-PRB pod probe for 7906 Group MCUs
SSOP42B-450 converter board for 42-pin SSOP (42P2R-A)
M37906T-PRB User's Manual (this manual)
1
1
1
1
1
1
M37906T-PRB User's Manual (Japanese)
M37906T-PRB Repair Request Sheet (English/Japanese)
Technical Support Communication Sheet (English/Japanese)
Please keep the M37906T-PRB’s packing box and cushion material in your place for reuse at a later
time when sending your product for repair or other purposes. Always use these packing box and
cushion material when transporting the M37906T-PRB.
If any of these items are missing or found faulty, please contact your local distributor. Also, if there
is any question or doubt about the packaged product, contact your local distributor.
2.3 Other Tool Products Required for Development
To bring forward programs development on the 7906 Group MCUs, the products listed below are
necessary in addition to the package components listed above. Get them separately.
Other tool products
Emulator main unit
Emulation pod main unit
Emulator debugger
Converter board
PC4701
M37900T2-RPD-E
M3T-PD79 Ver.2.10 or greater is recommended
Converter board FLX-42SPB
Necessary for using SDIP (42P4B)
To purchase these products, contact your nearest distributer.
( 17 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 System Configuration
Figure 2.1 System configuration
Products (2) and (3) shown in Figure 2.1 are included with this product. Get (1) in Figure 2.1
separately.
(1) Emulation pod main unit (M37900T2-RPD-E)
This is an emulation pod common for 7900 Series MCUs. By replacing the pod probe on the tip
of the emulation pod, it will support future 7900 Series MCUs (option).
(2) Pod probe (M37906T-PRB)
This pod probe is equipped with the emulator MCU, M37906FCCWP.
(3) Pitch converter board for 42-pin 0.8mm-pitch SSOP (SSOP42B-450)
Board for connecting the pod probe to the socket for 42-pin 0.8mm-pitch SSOP on the target
system.
For details on the connection, refer to "3.4 Connecting the Target System" (page 24).
( 18 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Setting Up
This chapter describes switch settings required for using this product and how to connect this product to the PC4701 and
the target system.
3.1 Switch Settings ........................................................................................................................... 20
3.2 A-D Conversion Bypass Capacitor ............................................................................................ 21
3.3 Connecting the Emulation Pod Main Unit ................................................................................. 22
3.4 Connecting the Target System.................................................................................................... 24
( 19 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3. Setting Up
With this product, it is necessary to set the following according to your target system.
• Setting switches
• Mounting the A-D conversion bypass capacitor
3.1 Switch Settings
It is necessary to set the switches of the M37906T-PRB for debugging according to the target system.
Figure 3.1 shows the positions of the switches of the M37906T-PRB, and Table 3.1 shows the switch
settings.
Figure 3.1 Positions of the switches and their factory-settings
Table 3.1 Switch settings of M37906T-PRB
Function
Switch No.
Switch setting
N.C XOUT
Does not output XOUT
XOUT
N.C
XOUT
output
selected
JP1
Outputs XOUT
U
(Factory-setting)
U
PLL filter
circuit
JP2
selected
T
T
When using the PLL filter circuit on When using the PLL filter circuit on
the target system or not using the the pod probe
PLL function (Factory-setting)
CAUTION
Note on Switch Settings:
• Always shut OFF power before setting switches. The power ON state could destroy
internal circuits.
( 20 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 A-D Conversion Bypass Capacitor
This product has foot patterns on the board for mounting a bypass capacitor for the A-D converter
circuit. Mount a suitable bypass capacitor as occasion demands.
Figure 3.2 shows the position of the bypass capacitor.
Figure 3.2 Foot patterns of A-D conversion bypass capacitor
IMPORTANT
Note on the Operation of A-D Converter:
• The characteristics of A-D converter differ from those of actual MCU because there
are a converter board and other devices between the evaluation MCU and the target
system. Make the final evaluation of the A-D converter with the actual MCU.
( 21 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Connecting the Emulation Pod Main Unit
The emulation pod for 7906 Group MCUs consists of the following two products.
(1) Emulation pod
(2) Pod probe
: M37900T2-RPD-E
: M37906T-PRB
It is necessary to connect the M37906T-PRB to the M37900T2-RPD-E for the emulation of 7906
Group MCUs. Figure 3.3 shows how to connect them.
(1) Unscrew the four screws of M37906T-PRB.
(2) Connect the connectors J3 and J4 of the M37900T2-
RPD-E's FLX100 to the connectors J3 and J4 of the
M37906T-PRB. And connect the connectors J1 and J2
of M37906T2-PRBM to the connectors J5 and J6 of the
M37906T-PRB.
(3) Fix the M37906T-PRB with the four screws.
Figure 3.3 Connecting pod probe M37906T-PRB
( 22 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
With the 7900 Series emulator system, the internal flash ROM of the emulator MCU is used as an
emulation memory.
As write/erase iterations to the internal ROM are limited, it is necessary to replace the MCU board
(M37906T-PRBM) depending on its life span.
How to replace the MCU board is shown in Figure 3.4.
(1) Unscrew the four screws of M37906T-PRB.
(2) Remove the M37906T-PRBM from the M37906T-PRB.
In this time, lift off the M37906T-PRBM horizontally.
Otherwise, the connector may cause a break.
Figure 3.4 Removing MCU board M37906T-PRBM
CAUTION
When Connecting Pod Probe:
• Be sure to turn off the power before making connections. Otherwise, the internal
circuits may be damaged.
• The small connectors (J3 and J4) of the M37906T-PRB are guaranteed for only 20
insertion/removal iterations.
• The small connectors (J1 and J2) of the M37906T-PRBM and those (J5 and J6) of
the M37906T-PRB are guaranteed for only 50 insertion/removal iterations.
( 23 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4 Connecting the Target System
There are three ways available to connect the emulation pod to target systems as shown in Figure 3.5.
*1 : These three products are available in a single package.
*2 : This converter board is included in this pod probe package.
: position of No. 1 pin
Figure 3.5 Connecting the target system
( 24 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 3.6 shows how to connect the pitch converter board SSOP42B-450 for 42-pin 0.8mm-pitch
SSOP.
(1) Mount the SSOP socket AXS69204201 (made by
Matsushita Electric Works, Ltd.) on the target system.
(2) Attach the SSOP42B-450 to the AXS69204201.
(3) Connect the M37906T-PRB to the SSOP42B-450.
Figure 3.6 Connecting the pitch converter board SSOP42B-450 for 42-pin 0.8mm-pitch SSOP
CAUTION
Notes on Connecting the Target System:
• Always shut OFF power before connecting the target system.
• Take care not to attach the converter board in an inverted position. It may cause a
fatal damage to the internal circuit.
( 25 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
( 26 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Specifications
This chapter describes specifications of this product.
4.1 Specifications ............................................................................................................................. 28
4.2 Electrical Characteristics ............................................................................................................ 28
4.3 Connection Diagram................................................................................................................... 29
4.4 External Dimensions of Pod Probe............................................................................................. 30
( 27 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4. Specifications
4.1 Specifications
Table 4.1 lists the specifications of the M37906T-PRB.
Table 4.1 Specifications of M37906T-PRB
Emulators
PC4701
Emulation pod main unit
Applicable MCUs
Emulator MCU
M37900T2-RPD-E
7906 Group MCUs
M37906FCCWP (pre-mounted on the M37906T-PRBM)
Single-chip mode
Usable MCU mode
Max. operating frequency 20MHz
Running
mode
Clock supply
Internal oscillator board, switchable to an external oscillator
Min. instruction execution time Approx. 50ns (20MHz)
Operating temperature range
Storage temperature range
Power supply to emulation pod
5 to 35°C (no dew)
-10 to 60°C (no dew)
Supplied from the emulator main unit
When connecting to the 0.8mm-pitch 42-pin SSOP foot pattern,
possible to connect via the SSOP42B-450.
42P2R-A
Connection to the
target system
When connecting to the 1.778mm-pitch 42-pin SDIP foot
pattern, possible to connect via the FLX-42SPB (option).
42P4B
4.2 Electrical Characteristics
The pins of MCU excluding XIN, MD0, MD1 and RESET* pins are directly connected to the target
system via the converter board.
Table 4.2 lists the electrical characteristics of the device used for XIN, MD0 and RESET* pins.
Table 4.2 Electrical characteristics of XIN, MD0 and RESET*
Standard values
Symbol
Parameter
Unit
VCC
Min.
Max.
-
VIH
VIL
IIN
High level input voltage
Low level input voltage
Input current
3.0 to 5.0
3.0 to 5.0
0.0 to 5.0
V
CC×0.7
V
V
-
-
V
CC×0.3
±0.1
µA
( 28 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 Connection Diagram
Figure 4.1 shows the connection diagram of the emulation pod for 7906 Group (M37900T2-RPD-E
and M37906T-PRB). This connection diagram mainly shows the interface section, and the circuits
which are not connected to the target system such as the emulator's control system are omitted.
Figure 4.1 Connection diagram
( 29 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
4.4 External Dimensions of Pod Probe
Figure 4.2 shows the external dimensions of M37906T-PRB.
Unit: mm
Figure 4.2 External dimensions of pod probe (M37906T-PRB)
( 30 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Troubleshooting
This chapter describes how to troubleshoot when this product does not work properly.
5.1 When the Emulator Debugger Does Not Operate ...................................................................... 32
(1) Errors Occur When Operating the Emulator Debugger
(When the target system is connected) ........................................................ 32
(2) Errors Occur When Operating the Emulator Debugger
(When the target system is not connected) .................................................. 33
5.2 Operation Differs from That of Actual MCUs ........................................................................... 33
(1) Initializing the Internal Resources of MCU at Power-on ..................................................... 33
(2) Oscillator Circuits ................................................................................................................. 33
(3) Flash ROM 2KB Expansion Area ........................................................................................ 33
(4) When the A-D Conversion Values are Different from Expected Values ............................. 33
(5) When the D-A Conversion Values are Different from Expected Values ............................. 33
( 31 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5. Troubleshooting
When this product does not work properly, check the following.
5.1 When the Emulator Debugger Does Not Operate
(1) Errors Occur When Operating the Emulator Debugger
(When the target system is connected)
Table 5.1 Checkpoints of errors when starting up the emulator debugger M3T-PD79 (target is connected)
Error
Checkpoint
Communication ERROR
Data is not sent to the target
Check all emulator debugger settings, interface cable
connections and switches on the rear of the PC4701
match.
- See the user's manuals of the PC4701 and emulator
debugger.
Target system is not constructed properly (1) Download the proper firmware.
- See the user's manuals of the emulator debugger.
(2) Recheck the connection between the PC4701, the
emulation pod and this product.
- See "3.3 Connecting the Emulation Pod Main Unit"
(page 22).
- See user's manual of the M37900T2-RPD-E.
The version of M3T-PD79 and the firmware Download the proper firmware.
on the target system are not same
- See the user's manual of the emulator debugger.
Target MCU is reset state
(1) Check the reset pin of the target system is pulled up.
(2) Check the reset pin of the target system has changed
from "L" to "H" level.
Target MCU cannot be reset
Flash ROM erase error occurred
(1) If the reset circuit of the target system has a watchdog
timer, disable the timer.
(2) Check power is properly supplied to the target system
and that the target system is properly grounded.
(3) Check your emulator debugger M3T-PD79 is Ver.2.10
or greater.
(4) The flash ROM of the MCU may be worn-out. Contact
your local distributor.
Target clock is stopped
Check the oscillation circuit of the target system is
oscillating properly.
Target MCU is not receiving power
Check power is properly supplied to the target system
and that the target system is properly grounded.
Not connected to target
Cannot connect to target
(1) Recheck the connection of the emulation pod and this
product.
- See "3.3 Connecting the Emulation Pod Main Unit"
(page 22).
(2) Recheck the connection of the SSOP42B-450 and
the socket.
- See "3.4 Connecting the Target System" (page 24).
Target MCU is uncontrollable
Reset target system
Check the program is not accessing to the unused area.
( 32 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
(2) Errors Occur When Operating the Emulator Debugger
(When the target system is not connected)
Table 5.2 Checkpoints of errors when starting up the emulator debugger M3T-PD79 (target is not connected)
Error
Checkpoint
Communication ERROR
Data is not sent to the target
Check all emulator debugger settings, interface cable
connections and switches on the rear of the PC4701
match.
- See the user's manuals of the PC4701 and emulator
debugger.
Target system is not constructed properly (1) Download the proper firmware.
- See the user's manual of the emulator debugger.
(2) Recheck the connection between the PC4701, the
emulation pod and this product.
- See "3.3 Connecting the Emulation Pod Main Unit"
(page 22).
- See user's manual of the M37900T2-RPD-E.
The version of M3T-PD79 and the firmware Download the proper firmware.
on the target are not same
- See the user's manual of the emulator debugger.
Target MCU cannot be reset
Flash ROM erase error occurred
(1) Check your emulator debugger M3T-PD79 is Ver.2.10
or greater.
(2) The flash ROM of the MCU may be worn-out. Contact
your local distributor.
Target MCU is uncontrollable
Reset target system
(1) Check the program is not accessing to the unused
area.
(2) When using the PLL circuit, check the switch settings
of the pod probe.
- "3.1 Switch Settings" (page 20).
5.2 Operation Differs from That of Actual MCUs
(1) Initializing the Internal Resources of MCU at Power-on
With this product, the internal resources of the MCU are initialized when starting up the emulator.
Therefore, the operation differs from that of actual MCUs.
(2) Oscillator Circuits
Make note of the fact that in the oscillator circuit where a resonator is connected between the XIN and
XOUT pins, oscillation does not occur because a flexible cable, buffer IC and other devices are used
between the emulator MCU and the target system.
(3) Flash ROM 2KB Expansion Area
In the DUMP window of emulator debugger M3T-PD79, the data of flash ROM 2KB expansion area
is displayed regardless of the setting of SFR area.
(4) When the A-D Conversion Values are Different from Expected Values
The A-D converter characteristics differ from actual MCU characteristics because there are a
converter board and other devices between the MCU and the target system. Make the final evaluation
of the A-D converter with the actual MCU.
(5) When the D-A Conversion Values are Different from Expected Values
The D-A converter characteristics differ from actual MCU characteristics because there are a
converter board and other devices between the MCU and the target system. Make the final evaluation
of the D-A converter with the actual MCU.
( 33 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
( 34 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Maintenance and Warranty
This chapter describes how to maintenance, repair provisions and how to request for repair.
6.1 Maintenance ............................................................................................................................... 36
6.2 Warranty ..................................................................................................................................... 36
6.3 Repair Provisions........................................................................................................................ 36
6.4 How to Request for Repair ......................................................................................................... 37
( 35 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 6. Maintenance and Guarantee
6.1 Maintenance
If dust or dirt collects on any equipment of your emulation system, wipe it off with a dry soft cloth.
Do not use thinner or other solvents because these chemicals can cause the equipment's surface
coating to separate.
6.2 Guarantee
If your product becomes faulty within one year after its purchase while being used under good
conditions by observing "Precautions for Safety" described in Chapter 1 of this user's manual, we will
repair or replace your faulty product free of charge. Note, however, that if your product's fault is raised
by any one of the following causes, we will repair it or replace it with new one with extra-charge:
• Misuse, abuse, or use under extraordinary conditions
• Unauthorized repair, remodeling, maintenance, and so on
• Inadequate user's system or misuse of it
• Fires, earthquakes, and other unexpected disasters
In the above cases, contact your local distributor. If your product is being leased, consult the leasing
company or the owner.
6.3 Repair Provisions
(1) Repair with extra-charge
The products elapsed more than one year after purchase can be repaired with extra-charge.
(2) Replacement with extra-charge
If your product's fault falls in any of the following categories, the fault will be corrected by
replacing the entire product instead of repair, or you will be advised to purchase new one,
depending on the severity of the fault.
• Faulty or broken mechanical portions
• Flaw, separation, or rust in coated or plated portions
• Flaw or cracks in plastic portions
• Faults or breakage caused by improper use or unauthorized repair or modification
• Heavily damaged electric circuits due to overvoltage, overcurrent or shorting of power supply
• Cracks in the printed circuit board or burnt-down patterns
• Wide range of faults that makes replacement less expensive than repair
• Unlocatable or unidentified faults
(3) Expiration of the repair period
When a period of one year elapses after the model was dropped from production, repairing
products of the model may become impossible.
(4) Transportation fees at sending your product for repair
Please send your product to us for repair at your expense.
( 36 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
6.4 How to Request for Repair
If your product is found faulty, follow the procedure below to send your product for repair.
Customer
Distributor
Fill in the Repair Request Sheet included with this product, then send it
along with this product for repair to your local distributor. Make sure
that information in the Repair Request Sheet is written in as much detail
as possible to facilitate repair.
After checking the contents of fault, the distributor should please send
the faulty product along with the Repair Request Sheet to Renesas
Solutions Corp.
Renesas Solutions When the faulty product is repaired, it will be returned to the customer
at the earliest convenience.
CAUTION
Note on Transporting the Product:
• When sending your product for repair, use the packing box and cushion material supplied with this
product when delivered to you and specify handling caution for it to be handled as precision
equipment. If packing of your product is not complete, it may be damaged during transportation.
When you pack your product in a bag, make sure to use conductive polyvinyl supplied with this
product (usually a blue bag). When you use other bags, they may cause a trouble on your product
because of static electricity.
( 37 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMO
( 38 / 40 )
Download from Www.Somanuals.com. All Manuals Search And Download.
M37906T-PRB User's Manual
Rev.1.00
September 1, 2003
REJ10J0288-0100Z
COPYRIGHT ©2003 RENESAS TECHNOLOGY CORPORATION
AND RENESAS SOLUTIONS CORPORATION ALL RIGHTS RESERVED
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|