Regency Indoor Fireplace G36D LP PROPANE User Guide

Owners &  
G36D Zero Clearance Direct Vent Gas Fireplace  
Installation Manual  
MODELS: G36D-NG Natural Gas G36D-LP Propane  
WARNING: Iftheinformationintheseinstructionsarenotfollowedexactly,  
a fire or explosion may result causing property damage, personal injury  
or loss of life.  
FOR YOUR SAFETY  
What to do if you smell gas:  
FOR YOUR SAFETY: Do not store or use gasoline or other flammable  
vapors and liquids in the vicinity of this or any other appliance. Installation  
and service must be performed by a qualified installer, service agency or  
the gas supplier.  
Do not try to light any appliance.  
Do not touch any electrical switch:  
do not use any phone in your building  
Immediately call your gas supplier  
from a neighbour's phone. Follow the  
gas supplier's instructions.  
This appliance may be installed in an aftermarket, permanently located,  
manufactured home (USA only) or mobile home, where not prohibited by  
local codes. This appliance is only for use with the type of gas indicated on  
the rating plate. This appliance is not convertible for use with other gases,  
unless a certified kit is used.  
If you cannot reach your gas supplier,  
call the fire department.  
Tested by:  
Installer: Please complete the details on the back cover  
and leave this manual with the homeowner.  
Homeowner: Please keep these instructions for future reference.  
918-156b  
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4  
01/04/06  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Page  
Page  
Safety Label  
Operating Instructions  
Safety Label ............................................................... 4  
Operating Instructions .............................................. 32  
Lighting Procedure ................................................... 32  
Shutdown Procedure................................................ 32  
First Fire ................................................................... 32  
Aeration Adjustment ................................................. 32  
Normal Operating Sounds of  
Installation  
Important Message..................................................... 5  
Before You Start ......................................................... 5  
General Safety Information ........................................ 5  
Installation Checklist................................................... 5  
Locating Your Gas Stove............................................ 6  
Manufactured Home Additional Requirements........... 6  
G36D Unit Dimensions............................................... 6  
Clearances ................................................................. 7  
Mantel Leg Clearance ................................................ 7  
Framing and Finishing................................................ 7  
Combustible Mantel Clearances ................................ 8  
Unit Assembly Prior to Installation  
Gas Appliances.................................................. 33  
Lighting Plate Instructions ........................................ 33  
Maintenance  
Maintenance Instructions ........................................ 33  
General Vent Maintenance....................................... 34  
Gold Plated or Brass Trim ........................................ 34  
Log Replacement ..................................................... 34  
Thermopile/Thermocouple ....................................... 34  
Glass Gasket............................................................ 34  
Door Glass ............................................................... 34  
Flush Glass Replacement ........................................ 34  
Removing Valve........................................................ 35  
Installing Valve.......................................................... 35  
Top Standoff Assembly ........................................ 9  
Top Facing Support & Side Nailing Strip  
Assembly....................................................... 9  
Venting Introduction.................................................... 9  
Exterior Vent Termination Locations......................... 10  
Venting ......................................................................11  
Direct Vent System (Flex) ...................................11  
Rigid Pipe Components List............................... 12  
Rigid Pipe Venting Systems............................... 13  
Venting - Horizontal Terminations ............................ 14  
Venting - Dura-Vent Horizontal Installations............. 15  
Venting - Vertical Terminations ................................. 16  
Vertical Terminations - Co-linear Flex System.......... 18  
Venting Arrangements........................................ 19  
Horizontal Installations ............................................. 20  
Venting - Installation Procedures for Direct Vent  
Parts List  
Parts List .................................................................. 36  
Warranty  
Warranty................................................................... 39  
System (Flex)..................................................... 22  
System Data............................................................. 23  
High Elevation .......................................................... 23  
Gas Line Installation................................................. 23  
Pilot Adjustment........................................................ 23  
Gas Pipe Pressure Test............................................ 23  
SIT Valve Description ............................................... 23  
Conversion to Propane............................................. 24  
Log Set Installation................................................... 25  
Flush Door - Standard.............................................. 28  
Optional Flush Trim .................................................. 28  
Flush Louvers........................................................... 28  
Remote Control (optional) ........................................ 29  
Wall Switch (optional)............................................... 29  
Wall Thermostat (optional) ....................................... 29  
Wiring Diagram......................................................... 30  
Fan Installation (optional)......................................... 31  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY LABEL  
This is a copy of the label that accompanies  
each G36D Zero Clearance Direct Vent Gas  
Fireplace. We have printed a copy of the  
contents here for your review. The safety label  
is located on the front inside base of the unit,  
visible when the bottom louver is open.  
NOTE: UltraGlow units are constantly being  
improved. Check the label on the unit and if  
there is a difference, the label on the unit is  
the correct one.  
For the State of Massachusetts, installation  
and repair must be done by a plumber or  
gasfitter licensed in the Commonwealth of  
Massachusetts.  
For the State of Massachusetts, flexible  
connectors shall not exceed 36 inches in  
length.  
For the State of Massachusetts, the appli-  
ances individual manual shut-off must be a  
t-handle type valve.  
4
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
14) Under no circumstances should any solid  
fuels (wood, paper, cardboard, coal, etc.)  
be used in this appliance.  
IMPORTANT:  
SAVE THESE  
INSTRUCTIONS  
CLOTHING OR OTHER FLAMMABLE  
MATERIALSHOULDNOTBEPLACED  
ON OR NEAR THE APPLIANCE.  
15) The appliance area must be kept clear and  
free of combustible materials, (gases and  
other flammable vapours and liquids).  
TheG36D-NGorG36D-LPDirectVentFireplace  
must be installed in accordance with these in-  
structions. Carefully read all the instructions in  
this manual first. Consult the "authority having  
jurisdiction" to determine the need for a permit  
prior to starting the installation. It is the respon-  
sibility of the installer to ensure this fireplace  
is installed in compliance with manufacturer's  
instructions and all applicable codes.  
GENERAL SAFETY  
INFORMATION  
1) The appliance installation must conform  
with local codes or, in the absence of local  
codes,withthecurrentCanadianorNational  
Gas Codes, CAN1-B149 or ANSI Z223.1  
Installation Codes.  
Emissions from burning wood or gas could  
contain chemicals known to the State of Cali-  
fornia to cause cancer, birth defects or other  
reproductive harm.  
INSTALLATION  
CHECKLIST  
2) The appliance when installed, must be  
electrically grounded in accordance with  
localcodes, orintheabsenceoflocalcodes  
with the current National Electrical Code,  
ANSI/NFPA 70 or CSA C22.1 Canadian  
Electrical Code.  
1) Locate appliance  
BEFORE YOU START  
Safe installation and operation of this appli-  
ance requires common sense, however, we  
are required by the Canadian Safety Standards  
and ANSI Standards to make you aware of the  
a) Room location, page 6  
b) Clearances to Combustibles, pages 6  
-8.  
c) Mantle Clearances, page 8  
d) Framing & Finishing Requirements,  
page 7  
3) See general construction and assembly  
instructions.Theapplianceandventshould  
be enclosed.  
e) Venting Requirements, pages 10 - 17.  
INSTALLATIONANDREPAIRSHOULD  
BE DONE BY A QUALIFIED SERVICE  
PERSON. THE APPLIANCE SHOULD  
BE INSPECTED BEFORE USE AND  
AT LEAST ANNUALLY BY A PRO-  
FESSIONAL SERVICE PERSON.  
MORE FREQUENT CLEANING MAY  
BE REQUIRED DUE TO EXCESSIVE  
LINT FROM CARPETING, BEDDING  
MATERIAL, ETC. IT IS IMPERATIVE  
THAT CONTROL COMPARTMENTS,  
BURNERS AND CIRCULATING AIR  
PASSAGEWAYS OF THEAPPLIANCE  
BE KEPT CLEAN.  
2) Assemble Top Standoffs and Top Facing  
Support and Side Nailing Strips, page 9.  
(NOTE: must be done before installing unit  
into fireplace.)  
4) This appliance must be connected to the  
specified vent and termination cap to the  
outsideofthebuildingenvelope.Nevervent  
to another room or inside a building. Make  
sure that the vent is fitted as per Venting  
instructions.  
3) Install vent, pages 20-22.  
4) Make gas and electrical connections. Test  
the pilot. Must be as per diagram. Page  
23.  
5) Inspect the venting system annually for  
blockage and any signs of deterioration.  
6) Venting terminals shall not be recessed into  
5) Install log set where indicated on page 25  
a wall or siding.  
- 27.  
7) Any safety glass removed for servicing  
must be replaced prior to operating the  
appliance.  
6) Install Flush Door Front (Standard) and  
optional Flush Gold Trim, page 28.  
DUE TO HIGH TEMPERATURES, THE  
APPLIANCE SHOULD BE LOCATED  
OUT OF TRAFFIC AND AWAY FROM  
FURNITURE AND DRAPERIES.  
7) Install Louvers page 28.  
8) To prevent injury, do not allow anyone who  
is unfamiliar with the operation to use the  
fireplace.  
8) InstalloptionalWallSwitch,RemoteControl,  
or Wall Thermostat, page 29.  
WARNING:FAILURETOINSTALLTHIS  
APPLIANCE CORRECTLY WILL VOID  
YOUR WARRANTY AND MAY CAUSE  
A SERIOUS HOUSE FIRE.  
9) Wear gloves and safety glasses for protec-  
9) Final check.  
tion while doing required maintenance.  
Before leaving this unit with the customer, the  
installer must ensure that the appliance is fir-  
ing correctly and operation fully explained  
to customer.  
10) Be aware of electrical wiring locations in  
walls and ceilings when cutting holes for  
termination.  
CHILDREN AND ADULTS SHOULD  
BE ALERTED TO THE HAZARDS OF  
HIGHSURFACETEMPERATURES,ES-  
PECIALLY THE FIREPLACE GLASS,  
AND SHOULD STAY AWAY TO AVOID  
BURNS OR CLOTHING IGNITION.  
11) Under no circumstances should this ap-  
pliance be modified. Parts that have to be  
removed for servicing should be replaced  
prior to operating this appliance.  
12) Installationandanyrepairstothisappliance  
should be done by a qualified service per-  
son. A professional service person should  
be called to inspect this appliance annually.  
Make it a practice to have all of your gas  
appliances checked annually.  
YOUNG CHILDREN SHOULD BE  
CAREFULLY SUPERVISED WHEN  
THEY ARE IN THE SAME ROOM AS  
THE APPLIANCE.  
13) Do not slam shut or strike the glass door.  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
INSTALLATION  
This includes:  
MANUFACTURED  
MOBILE HOME  
ADDITIONAL  
5) This appliance is Listed for bedroom instal-  
lations when used with a Listed Millivolt  
Thermostat. Some areas may have further  
requirements, check local codes before  
installation.  
1) Clockingtheappliancetoensurethecorrect  
firing rate (rate noted on label 26,000 Btu/h)  
after burning appliance for 15 minutes.  
REQUIREMENTS  
2) Ifrequired,adjustingtheprimaryairtoensure  
that the flame does not carbon. First allow  
the unit to burn for 15-20 min. to stabilize.  
6) The G36D Direct Vent Gas Fireplace is  
approved for alcove installations, which  
meet the clearances listed on this page.  
1) Ensure that structural members are not cut  
or weakened during installation.  
CAUTION:Any alteration to the product that  
causes sooting or carboning that results  
in damage is not the responsibility of the  
manufacturer.  
2) Ensure proper grounding using the #8  
7) We recommend that you plan your instal-  
lation on paper using exact measurements  
for clearances and floor protection before  
actually installing this appliance. Have a  
qualifiedinspector,dealer,orinstallerreview  
your plans before installation.  
ground lug provided. See page 29.  
LOCATING YOUR  
GAS STOVE  
Note: For vent terminations see page 10.  
1) When selecting a location for your stove,  
ensure that the clearances outlined on this  
page are met.  
G36D UNIT DIMENSIONS  
2) Provide adequate clearances for servic-  
ing.  
3) The appliance must be installed on a flat,  
solid, continuous surface (e.g. wood, metal,  
concrete).Thismaybetheoor,orraisedup  
on a platform to enhance its visual impact.  
If the appliance is going to be installed on  
carpeting, combustiblelinoleumtileorother  
combustible material other than wood floor-  
ing, the appliance must be installed on a  
metal or wood panel extending the full width  
and depth of the appliance.  
4) TheG36DDirectVentGasFireplacecanbe  
installedinarecessedpositionorframedout  
into the room as inA, B, C, D. See Diagram  
1.  
A) Flat on Wall  
B) Flat on Wall Corner  
C) Recessed into  
Wall/Alcove  
D) Corner  
Diagram 1  
6
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
2) Frame in the enclosure for the unit with  
framing material. The framed opening is  
37-1/4" high x 36-1/4" wide x 17-3/8" deep  
(946mm high x 921mm wide x 441mm  
deep).  
MANTEL LEG  
CLEARANCES  
Combustible mantel leg clearances as per  
diagram below:  
CLEARANCES  
The clearances listed below are Minimum  
distances unless otherwise stated:  
A major cause of chimney related fires is  
failure to maintain required clearances (air  
space) to combustible materials. It is of the  
greatest importance that this fireplace and  
vent system be installed only in accordance  
with these instructions.  
Clearance to Combustibles from:  
Back  
Side  
0"  
0"  
0"  
(0mm)  
(0mm)  
(0mm)  
Floor  
NOTE: The minimum floor clearance must  
be maintained from the top surface of the  
carpeting, tile, etc.  
Maximum 1-1/2" projection at 2" minimum  
clearance.  
Minimum Clearance from Top of Unit to:  
Mantel* Minimum  
Ceiling from top of unit.  
7"  
(177mm)  
32" (1016mm)  
FRAMING AND  
FINISHING  
Side Wall Clearance  
Flush Front  
6"  
(152mm)  
1) Determine the total thickness of facing  
material (e.g. drywall plus ceramic tiles) to  
allow the finished surface to be flush with  
the front of the unit. Total facing thickness  
canvaryfrom1/2"(13mm)to1-1/4"(32mm)  
thick.  
Horizontal Vent Clearances  
Top  
2-1/2" (64mm)  
1-1/2" (38mm)  
1-1/2" (38mm)  
Side  
Bottom  
Vertical Vent Clearances  
1-1/4" (32mm)  
Framing Dimensions  
Alcove Clearances**:  
Max. Depth  
A
B
C
D
36" (914mm)  
48" 1219mm)  
72" 1829mm)  
36-1/4" 37-1/4" 17-3/8" 46-1/2"*  
921mm 946mm 441mm 1181mm*  
* 'D' is Minimum height to combustible materi-  
Min. Width  
Min. Height  
* see mantle clearance instructions  
(pages 7 & 8).  
als including the Minimum 2-1/2" (64mm) Top  
clearance to the Horizontal Vent.  
WARNING:  
3) For exterior walls, insulate the enclosure to  
the same degree as the rest of the house,  
apply vapour barrier and drywall, as per lo-  
cal installation codes. (Do not insulate the  
fireplace itself.)  
Fire hazard is an extreme risk if  
these clearances are not adhered to.  
It is of greatest importance that this  
fireplace and vent system be  
installed only in accordance with  
these instructions.  
4) The top of the unit must not be closer than  
32" (813mm) to the ceiling.  
Install Side Nailing Strips, Top Facing  
Support, and Top Standoffs before unit is  
slipped into position. See page 9 for as-  
sembly details.  
The HeatWave Duct Kit has different clearance and framing  
requirements, check the HeatWave manual for details.  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
INSTALLATION  
COMBUSTIBLE MANTELS  
Because of the extreme heat this fireplace emits, the mantel clearances are critical.  
Combustible mantel clearances from top of unit are shown in the diagram below.  
Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered with a non-combustible  
board.  
These drawings are to scale at 1:6 (one inch = 6 inches)  
Mantel can be installed anywhere in shaded area or higher using the above scale.  
Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the paint may discolour.  
8
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
Top Header  
3) Attach the standoff securely to the top  
with 2 screws per standoff (on opposite  
corners).  
10"dia.hole  
throughwall  
for Flex  
1/2"  
Drywal  
orforDuraVent  
"C" Screw Position:  
For a facing material depth of 1-1/4"  
(32mm), the top facing support must be  
reversed.  
2"  
3-1/2" 4"  
Openingforgas  
connectino  
17-1/8"  
Note: 40-1/2" (1029mm) is the minimum  
height for both flex termination or  
Simpson Dura-Vent venting.  
Top Facing Support and  
Side Nailing Strips  
5) The unit does not have to be completely  
enclosedinachase.The clearanceontopof  
the unit is 0" to the standoffs so combustible  
building materials can be laid directly on top  
of the standoffs. You must maintain clear-  
ance from the vent to combustible materials  
for flex, see Vent Clearances, page 7.  
Determine the total thickness of facing mate-  
rial (e.g. drywall plus ceramic tiles) to allow the  
finished surface to be flush with the front of the  
unit. Total facing thickness can vary from 1/2"  
(13mm) to 1-1/4" (32mm) thick.  
TheTopFacingSupport&SideNailingStripscan  
be mounted in 3 different positions depending  
on the thickness of the facing material.  
6) Use steel studs for framing where the  
1-1/2" (38mm) clearance from the vent to  
combustiblematerialcannotbemaintained,  
e.g. front top header.  
2) Use the same screw hole position for the  
Side Nailing Strips as was used for the Top  
Facing Support. Attach each side nailing  
strip using 3 screws.  
Screw  
Facing Material  
Depth  
Position  
VENTING  
A
1/2"  
/ 13mm  
UNIT ASSEMBLY  
PRIOR TO  
INTRODUCTION  
B
7/8"  
/ 22mm  
/ 32mm  
C*  
1-1/4"  
The G36D uses the "balanced flue" technology  
Co Axial system. The inner liner vents products  
ofcombustiontotheoutsidewhiletheouterliner  
draws outside combustion air into the combus-  
tion chamber thereby eliminating the need to  
use heated room air for combustion and losing  
warm room air up the chimney.  
INSTALLATION  
* For "C" screw position the top facing support  
is reversed.  
TheTop Facing Support, the Side Nailing Strips  
and the 2 Top Standoffs must be correctly po-  
sitioned and attached to the top before unit is  
slipped into position.  
1) Mount Top Facing Support using the 3  
suppliedscrewsintothethreepre-punched  
screw holes on the top front of the unit. Use  
hole positionsA, B, or C depending on your  
facing depth.  
Top Standoff Assembly  
Note: These flue pipes must not be con-  
nected to any other appliance.  
The top standoffs are shipped in a flat position  
and must be folded into shape and attached.  
The gas appliance and vent system must be  
vented directly to the outside of the building,  
and never be attached to a chimney serving a  
separate solid fuel or gas burning appliance.  
Eachdirectventgasappliancemustuseit'sown  
separate vent system. Common vent systems  
are prohibited.  
1) Remove the standoffs from the fireplace  
top.  
2) Takeeachstandoffandbendintothecorrect  
shape. Bend up at the bend lines until the  
screw holes in the standoff and the pre-  
punched screw holes on the fireplace top  
line up.  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
INSTALLATION  
EXTERIOR VENT TERMINATION LOCATIONS  
10  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
VENTING  
UltraGlow Direct Vent System (Flex)  
Horizontal Terminations Only  
These venting systems, in combination with the G36D Direct Vent Gas Fireplace, have been tested and listed as a direct vent heater system by  
Warnock Hersey. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram on page 10.  
UltraGlow Direct Vent (Flex) System Termination Kit (Part # 946-515) includes all the parts needed to install the G36D with a maximum  
total run of 4 feet.  
1) 6-7/8" dia. flexible liner (4 ft. length)  
2) 4" dia. flexible liner (4 ft. length)  
3) spring spacers (4)  
4) thimble (2)  
5) AstroCap termination cap (1)  
6) screws (12)  
7) tube of Mill Pac (1)  
8) plated screws (8)  
9) screws #8 x 1-1/2" Drill Point, Stainless Steel (4)  
Notes:  
1) Liner sections should be continuous without any joints or seams.  
2) Only Flex pipe purchased from Regency may be used for Flex installations.  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
INSTALLATION  
RIGID PIPE VENTING COMPONENTS LIST  
All Simpson Dura-Vent components are available directly from FPI.  
Description  
Simpson Dura-Vent  
Direct VentGSR  
Selkirk  
AmeriventR  
Direct Vent  
Direct-TempTM  
6" Pipe Length, Galvanized  
6" Pipe Length, Black  
908  
4DT-6  
N/A  
908B  
N/A  
4DT-6B  
N/A  
N/A  
7" Pipe Length, Galvanized  
7" Pipe Length, Black  
4D7  
N/A  
907  
N/A  
4DT-9  
4D7B  
N/A  
9" Pipe Length, Galvanized  
9" Pipe Length, Black  
907B  
906  
4DT-9B  
4DT-12  
4DT-12B  
4DT-18  
4DT-18B  
4DT-24  
4DT-24B  
4DT-36  
4DT-36B  
4DT-48  
4DT-48B  
N/A  
12" Pipe Length, Galvanized  
12" Pipe Length, Black  
4D12  
4D12B  
N/A  
906B  
N/A  
18" Pipe Length, Galvanized  
18" Pipe Length, Black  
N/A  
904  
N/A  
4D2  
24" Pipe Length, Galvanized  
24" Pipe Length, Black  
904B  
903  
4D2B  
4D3  
36" Pipe Length, Galvanized  
36" Pipe Length, Black  
903B  
902  
4D3B  
4D4  
48" Pipe Length, Galvanized  
48" Pipe Length, Black  
902B  
4D4B  
Adjustable Length, 11"-14", Galv.  
Adjustable Length, 11"-14", Black  
Adjustable Length, 17"-24", Black  
Adjustable Length, 7" Galvinized  
Adjustable Length, 7" Black  
Adjustable Length, 12" Galvinized  
Adjustable Length, 12" Black  
911  
4DT-AJ  
4DT-AJB  
N/A  
N/A  
911B  
917B  
N/A  
N/A  
N/A  
N/A  
4D7A  
4D7AB  
4D12A  
4D12AB  
N/A  
N/A  
N/A  
N/A  
N/A  
N/A  
45O Elbow, Galvinized  
45O Elbow, Black  
945  
4DT-EL45  
4DT-EL45B  
N/A  
4D45L  
4D45LB  
N/A  
945B  
945G  
945BG  
990  
45O Elbow, Swivel, Galvinized  
45O Elbow, Swivel, Black  
90O Elbow, Galvinized  
90O Elbow, Black  
N/A  
N/A  
4DT-EL90S  
4DT-EL90SB  
N/A  
4D90LS  
4D90LBS  
N/A  
990B  
990G  
990BG  
90O Elbow, Swivel, Galvinized  
90O Elbow, Swivel, Black  
N/A  
N/A  
Ceiling Support  
949 - n/a from FPI  
4DT-CS  
4DT-CSS  
4DT-WS/B  
4DT-OS  
4DT-WT  
N/A  
4DT-FS  
4DT-TP  
N/A  
4DFSP  
4DRSB  
4DWS  
N/A  
Cathedral Support Box  
Wall Support/Band  
941  
988  
Offset Support  
Wall Thimble, Black  
989 - n/a from FPI  
942  
940  
963  
N/A  
3951  
4DWT  
N/A  
Wall Thimble Support Box/Ceiling Support  
Firestop Spacer  
4DFSP  
4DFPB  
N/A  
Trim Plate, Black  
Brass Trim for Wall Thimble/Ceiling Support  
Attic Insulation Shield 12"  
Attic Insulation Shield - Cold Climates 36"  
N/A  
N/A  
N/A  
N/A  
4DAIS12  
4DAIS36  
Basic Horizontal Termination Kit (A)  
Horizontal Termination Kit (B)  
Vertical Termination Kit  
970  
971  
978  
4DT-HKA  
4DT-HKB  
4DT-VKC  
4DHTK2  
4DHTK1  
4DVTK  
High Wind Vertical Cap  
High Wind Horizontal Cap  
Horizontal Square Termination Cap  
Verical Termination Cap  
Storm Collar  
991  
985  
984  
980  
953  
N/A  
N/A  
N/A  
N/A  
4DT-HHC  
4DT-HVC  
4DT-SC  
4DHC  
4DVC  
4DSC  
Adjustable Flashing, 0/12-6/12  
Adjustable Flashing, 6/12-12/12  
943  
943S  
4DT-AF6  
4DT-AF12  
4DF  
4DF12  
Vinyl Siding Standoff  
Vinyl Siding Shield Plate  
950  
N/A  
4DT-VS  
4DT-VSP  
N/A  
N/A  
Snorkel Termination 14"  
Snorkel Termination 36"  
982  
981  
4DT-ST14  
4DT-ST36  
4D12S  
4D36S  
946-506/P  
510-994  
Vent Guard (Optional)  
946-208/P  
946-523/P  
946-206  
Vent Guard (Optional) - Riser Vent Terminal  
AstroCap Horizontal Cap  
Vinyl Siding Standoff - AstroCap  
Rigid Pipe Adaptor (must use with all rigid pip-  
ing)  
640-530/P  
Riser Vent Terminal  
12  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
RIGID PIPE VENTING SYSTEMS  
Horizontal or Vertical Terminations  
The minimum components required for a basic horizontal termination  
are:  
Flat Wall Installation  
Wall Thickness  
(inches)  
Vent Length  
1
1
1
1
1
Horizontal Termination Cap  
90o Elbow  
Required (inches)  
4"  
7"  
-
-
5-1/2"  
8-1/2"  
6"  
9"  
Rigid Pipe Adaptor  
Wall Thimble  
Length of pipe to suit wall thickness (see chart)  
10" - 11-1/2"  
9" - 14-1/2"  
15" - 23-1/2"  
12"  
11" - 14-5/8" Adj. Pipe  
17" - 24" Adj.  
Wallthickness ismeasuredfromthebackstandoffstotheinsidemounting  
surface of termination cap. For siding other than vinyl furring strips may  
be used, instead of the vinyl siding standoff, to create a level surface to  
mount the vent terminal. The Terminal must not be recessed into siding.  
Measure the wall thickness including furring strips.  
Pipe  
Corner Installation  
Wall Thickness  
(inches)  
3-1/4"  
7-3/4" - 16-1/4"  
Vent Length  
Required (inches)  
11" - 14-5/8" Adj. Pipe  
17" - 24" Adj. Pipe  
6" + 12"  
-
6-3/4"  
7-1/4"  
-
-
8-3/4"  
5-3/4"  
If a Vinyl Siding Standoff is required (it must be used with vinyl siding),  
measure to outside surface of wall without siding and add 2 inches.  
9" + 9"  
6" + 9"  
4-1/4"  
Vertical  
Terminal  
Storm Collar  
(Part # 953)  
Vinyl Siding  
Standoff (Optional)  
Alternate  
Horizontal  
Termination  
Caps  
(Part #950)  
Flashing  
943 or 943S  
Ceiling Firestop  
(Part # 963)  
Horizontal  
Termination Cap  
(Part# 946-523/P)  
Wall Thimble  
(Part # 942)  
Pipe Length  
Adj.Pipe Length  
11" - 14-5/8"  
90o Elbow  
WARNING:  
Do not combine venting components from  
different venting systems.  
24" Pipe  
Length  
TM  
However use of the the AstroCap and FPI  
Riser is acceptable with all systems.  
This product has been evaluated by Intertek for  
using a Dura-Vent Flue Adaptor in conjunction  
with Selkirk Direct-Temp and Ameri Vent Direct  
venting systems. Use of these systems with the  
DirectVentGSstartingcollarisdeemedaccept-  
able and does not affect the Intertek WHI listing  
of components.  
Rigid Pipe Adaptor  
(Part# 510-994)  
When using piping other than Simpson  
Dura-Vent, 3 screws must be used to  
secure rigid pipe to adaptor.  
The FPI AstroCapTM and FPI Riser Vent terminal is certified for installations using FPI venting systems as well as Simpson Dura-Vent®, Direct Vent GS,  
American Metal Products, Ameri Vent Direct vent and Selkirk Direct-Temp. FPITM, and FPI AstroCapTM are the proprietary trademarks of FPI Fireplace  
Products International Ltd. Dura-Vent® and Direct Vent GS are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
INSTALLATION  
RIGID PIPE VENTING ARRANGEMENTS - HORIZONTAL TERMINATIONS  
ULTRAGLOW DIRECT VENT SYSTEM (FLEX)  
(Propane & Natural Gas)  
The diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 90o elbow (two 45o elbows equal one 90o  
elbow).  
Note: Must use optional rigid pipe adaptor (Part # 510-994) when using rigid pipe vent systems.  
All Rigid Pipe Systems  
4" inner diameter  
6-5/8" outer diameter  
UltraGlow Flex Vent  
4" inner diameter  
6-7/8" inner diameter  
A vent guard should be used when-  
ever the termination is lower than  
the specified minimum or as per  
local codes.  
Note: UltraGlow Direct Vent System  
(Flex) is only approved for hori-  
zontal terminations.  
Maintain clearances to combustibles as listed on pages 7 and 8.  
Horizontal vent must be supported every 3 feet.  
Firestops are required at each floor level and whenever passing through a wall.  
14  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
RIGID PIPE VENTING ARRANGEMENTS - HORIZONTAL TERMINATIONS  
ULTRAGLOW DIRECT VENT SYSTEM (FLEX)  
(Propane & Natural Gas)  
The diagram below shows examples of horizontal termination arrangements using two 90o elbows (two 45o elbows equal one 90o elbow).  
Note:  
1) A maximum of two 90o elbows are permitted.  
2) A minimum of 6 ft. (1.8m) vertical from base of unit is required if two 90o elbows are used.  
3) Minimum distance between elbows is 2 ft. (0.6m).  
4) Determine the permitted range of horizontal termination arrangements by using chart on page 14  
and deducting 3 ft. (0.9m) from the maximum horizontal distance for the second 90o elbow.  
Iflength"B"isincreased,length"A"mustbe  
decreased by a corresponding amount.  
All Rigid Pipe Systems  
4" inner diameter  
6-5/8" outer diameter  
UltraGlow Flex Vent  
4" inner diameter  
6-7/8" inner diameter  
A vent guard should be used whenever the  
terminationislowerthanthespecifiedminimum  
or as per local codes.  
Maintain clearances to combustibles as listed on pages 7 and 8.  
Horizontal vent must be supported every 3 feet.  
Firestops are required at each floor level and whenever passing through a wall.  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
INSTALLATION  
RIDID PIPE VENTING ARRANGEMENTS - VERTICAL TERMINATIONS  
(Propane & Natural Gas)  
The G36D is approved for a maximum 23 ft. (7.0m) vertical, with a maximum 12 ft. (3.7m) horizontal offset  
using two 90o elbows (two 45o elbows equal one 90o elbow) with Rigid Pipe vent systems for Propane and  
Natural Gas, as per diagram 1.  
TheG36Disapprovedfora maximum37ft. (11.3m)straightvertical, includingamaximum20"(0.5m)horizontal  
offset using two 90o elbow (two 45o elbows equal one 90o elbow) with Rigid Pipe vent systems for Propane  
and Natural Gas, as per the diagram 2.  
Vent must be supported at offsets  
Maintain clearances to combustibles as listed on pages 7 and 8.  
Firestops are required at each floor level and whenever passing through a wall.  
Note: Must use optional rigid pipe adaptor when using rigid pipe vent systems (Part # 510-994).  
Note: UltraGlow Direct Vent System (Flex) is only approved for horizontal terminations.  
Diagram 1  
Diagram 2  
16  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
TheG36Disapprovedforamaximum37ft.(11.3m)straightvertical,withRigid  
Pipe vent systems for Propane and Natural Gas, as per the diagram 3.  
The shaded area in the diagram 3 shows all allowable combinations of straight  
vertical and offset to vertical terminations with Rigid Pipe vent systems for  
Propane and Natural Gas. Maximum two 45o elbows allowed.  
Vent must be supported at offsets  
Firestops are required at each floor level and whenever passing  
through a wall.  
Maintain clearances to combustibles as listed on pages 7 and 8.  
Diagram 3  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
INSTALLATION  
VERTICAL TERMINATION  
WITH CO-LINEAR FLEX SYSTEM  
THE APPLIANCE MUST NOT BE  
CONNECTED TO A CHIMNEY FLUE  
SERVING A SEPARATE SOLID FUEL  
BURNING APPLIANCE.  
Masonry chimneys may take various contours which the flexible liner will accommodate. However,  
keep the flexible liner as straight as possible, avoid unnecessary bending.  
The Air Intake pipe must be attached to the inlet air collar of the termination cap.  
This appliance is designed to be attached to  
two 3" (76mm) co-linear aluminium flex running  
the full length of the chimney. See the Venting  
Arrangements on next page for minimum and  
maximum heights.  
Co-linear DV  
Vertical Termination  
Cap # 946-529  
Required Parts:  
A maximum  
of two certified  
joiner kits  
may be used  
per length.  
#948-305 (35 ft)  
Part #  
Description  
946-529  
Co-linear DV Vertical  
Termination Cap  
948-305  
946-563  
Kit  
3" Flex - 35 ft.  
Co-Axial to Co-Linear Adapter  
Flex Liner  
which contains the following:  
Co-linear Flex Adapter  
Outer Pipe  
Inner Pipe Adapter  
Rigid Pipe Adaptor  
510-994  
Alternate Approved Caps  
Exhaust  
Flue  
980  
991  
Vertical Termination Cap  
High Wind Cap  
923GK 3" Co-linear Adapter with flashing  
Outer  
Pipe  
with Kit#  
946-563  
FPI Cabinet and/or Flat Wall Mantles  
may be used in these applications en-  
suring that clearances to combustibles  
are maintained.  
Air Intake  
Pipe Length  
Co-Linear  
Flex  
Adapter  
with Kit#  
946-563  
Rigid Pipe Adaptor  
# 510-994  
90 Degree  
Elbow  
Inner Pipe  
Adapter  
with Kit#  
946-563  
18  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
Venting Arrangements - Vertical Terminations  
with Co-linear Flex System for both  
Residential & Manufactured Homes  
into Masonry Fireplaces  
The shaded area in the diagrams show the  
allowable vertical terminations.  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19  
INSTALLATION  
b) Horizontal runs of vent must be  
supported every three feet. Wall straps  
are available for this purpose.  
HORIZONTAL  
INSTALLATIONS  
5) Mark the wall for a 10" x 10" square hole.  
The center of the square hole should line  
upwiththecenterlineofthehorizontalpipe.  
Cut and frame the 10 inch square hole in  
the exterior wall where the vent will be  
terminated. If the wall being penetrated is  
constructedofnon-combustiblematerial,i.e.  
masonry block or concrete, a 7"(178mm)  
dia. (7-1/2"(191mm) dia. for flex) hole is  
acceptable.  
Install the vent system according to the  
manufacturer's instructions included with  
the components.  
1) Set the unit in its desired location. Check  
to determine if wall studs or roof rafters are  
in the way when the venting system is at-  
tached. If this is the case, you may want to  
adjust the location of the unit. Rough in the  
gas preferably on the right side of the unit  
and the electrical (junction block is on the  
left side) on the left.  
Note: Riser Vent  
is only for use  
in above grade  
terminations.  
Note: With Dura-Vent,  
t h e m i n i -  
mum height  
is achieved  
by installing  
a 90o elbow  
directly to  
the rigid pipe  
adaptor.  
2) Direct Vent pipe and fittings are designed  
with special twist-lock connections to con-  
nect the venting system to the appliance  
flue outlet. A twist-lock appliance adaptor  
is an available option that must be used in  
conjunction with the Simpson Dura-Vent  
Direct Vent GS system.  
Diagram 3a  
*Diagrams 3 & 4: As specified in CGA B149  
InstallationCode.Localcodesorregulations  
may require different clearances.  
Below Grade Installation  
If the Snorkel Termination must be installed  
below grade, i.e. basement application, proper  
drainage must be provided to prevent water  
from entering the Snorkel Termination. Refer  
to Diagram 4. Do not attempt to enclose the  
Snorkel within the wall, or any other type of  
enclosure.  
3) Put a bead of silicone inside the outer sec-  
tion of the adapter and a bead of Mill Pac  
on the inner collar. Slip the adapter over the  
existinginnerandouteruecollarandfasten  
to the outer collar only with the 3 supplied  
screws (drilling pilot holes will make this  
easier). Level the fireplace and fasten it to  
the framing using nails or screws through  
the nailing strips.  
Diagram 2  
Note:  
a) The horizontal run of vent must be level,  
or have a 1/4 inch rise for every 1 foot  
of run towards the termination. Never  
allow the vent to run downward. This  
couldcausehightemperaturesandmay  
present the possibility of a fire.  
4) Assemble the desired combination of pipe  
and elbows to the appliance adaptor and  
twist-lock for a solid connection.  
b) The location of the horizontal vent ter-  
mination on an exterior wall must meet  
alllocalandnationalbuildingcodes,and  
must not be blocked or obstructed. For  
External Vent Terminal Locations, see  
diagram on page 10.  
Note:  
a) Twist-lockprocedure:Fourindentations,  
located on the female ends of pipes and  
fittings, are designed to slide straight  
onto the male ends of adjacent pipes  
and fittings, by orienting the four pipe  
indentations so they match and slide  
in to the four entry slots on the male  
ends,Diagram1.Pushthepipesections  
completely together, then twist-lock  
one section clockwise approximately  
one-quarter turn, until the two sections  
are fully locked. The female locking lugs  
will not be visible from the outside, on  
the Black Pipe or fittings. They may be  
located by examining the inside of the  
female ends.  
c) Snorkel Terminations:  
For installations requiring a vertical rise  
on the exterior of the building, 14-inch  
and 36-inch tall Snorkel Terminations  
are available, as well  
as the standard Riser  
Vent. Follow the same  
installationprocedures  
as used for stand-  
ard Horizontal  
Termination.  
Diagram 4  
N E V E R  
install the  
NOTE: For Snorkel terminations in ABOVE  
grade installations, follow national  
or local code requirements.  
s n o r k e l  
u p s i d e  
down.  
6) The arrow on the vent cap should  
be pointing up. Insure that the 1-1/2"  
clearances to combustible materials  
are maintained (Diagram 4). Install the  
termination cap.  
Diagram 1  
Note: Apply sealant "Mill-Pac" to inner  
pipe and high temperature silicone  
sealant to outer pipe on every twist-  
lock joint.  
Diagram 3  
20  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
VERTICAL  
4) Assemble the desired lengths of pipe and  
elbows. Ensure that all pipes and elbow  
connections are in the fully twist-locked  
position and sealed.  
TERMINATION  
1) Maintain the 1-1/2" clearances  
(air spaces) to combustibles  
when passing through ceilings,  
walls, roofs, enclosures, attic  
rafter, or other nearby combus-  
tible surfaces. Do not pack air  
spaces with insulation. Check  
pages 13-16 for the maximum  
vertical rise of the venting  
system and the maximum hori-  
zontal offset limitations.  
5) Cut a hole in the roof centered on the small  
drilled hole placed in the roof in Step 2. The  
hole should be of sufficient size to meet  
the minimum requirements for clearance  
to combustibles of 1-1/2". Slip the flashing  
under the shingles (shingles should overlap  
half the flashing) as per Diagram 4.  
Diagram 5  
The four wood screws provided should  
be replaced with appropriate fasteners for  
stucco, brick, concrete, or other types of  
sidings.  
2) Set the gas appliance in  
its desired location. Drop  
a plumb bob down from  
the ceiling to the position  
Diagram 1  
of the appliance flue exit,  
Note: If installing termination on a siding  
covered wall, a vinyl siding standoff  
or furring strips must be used to  
ensure that the termination is not  
recessed into the siding.  
and mark the location where the vent will  
penetrate the ceiling. Drill a small hole at  
his point. Next, drop a plumb bob from the  
roof to the hole previously drilled in the ceil-  
ing, and mark the spot where the vent will  
penetratetheroof.Determineifceilingjoists,  
roof rafters or other framing  
Diagram 4: The upper half of the flashing is  
installed under the roofing material and not  
nailed down until the chimney is installed. This  
allows for small adjustments.  
7) Before connecting the horizontal run of vent  
pipe to the vent termination, slide the Wall  
Thimble (Part # 942) over the vent pipe.  
6) Continue to assemble pipe lengths.  
will obstruct  
ing system.  
You may wish  
to relocate  
the appliance  
or to offset,  
as shown in  
Diagram 2 to  
avoid cutting  
load bearing  
members.  
thevent-  
Note: If an offset is necessary in the attic  
to avoid obstructions, it is important  
to support the vent pipe every 3 feet,  
to avoid excessive stress on the el-  
bows, and possible separation. Wall  
straps are available for this purpose  
(Diagram 2).  
8) Slide the appliance and vent assembly  
towards the wall carefully inserting the  
vent pipe into the vent cap assembly. It is  
important that the vent pipe extends into  
the vent cap sufficient distance so as to  
result in a minimum pipe overlap of 1-1/4  
inches. Secure the connection between the  
vent pipe and the vent cap by attaching the  
two sheet metal strips extending from the  
vent cap assembly into the outer wall of the  
vent pipe. Use the two sheet metal screws  
provided to connect the strips to the pipe  
section. See Diagram 6.  
Galvanized pipe is desirable above the roof-  
line due to its higher corrosion resistance.  
Continue to add pipe sections through the  
flashing until the height of the vent cap meets  
the minimum height requirements specified  
Diagram 2  
Note: Applysealant"Mill-Pac"toinnerpipe  
and high temperature silicone seal-  
ant to outer pipe on every twist-lock  
joint.  
Diagram 5  
Roof Pitch  
Minimum Vent Height  
3) A Firestop spacer must be installed in the  
floor or ceiling of every level. To install the  
Firestop spacer in a flat ceiling or wall, cut a  
10inchsquarehole.Frametheholeasshown  
in Diagram 3 and install the firestop.  
Feet  
2
Meters  
0.61  
0.61  
0.61  
0.76  
0.99  
1.22  
1.52  
1.83  
2.13  
2.29  
2.44  
flat to 7/12  
over 7/12 to 8/12  
over 8/12 to 9/12  
over 9/12 to 10/12  
over 10/12 to 11/12  
over 11/12 to 12/12  
over 12/12 to 14/12  
over 14/12 to 16/12  
over 16/12 to 18/12  
over 18/12 to 20/12  
over 20/12 to 21/12  
2
2
Diagram 6  
2.5  
3.25  
4
5
6
9) Install wall thimble in  
the center of the 10"  
square and attach  
with wood screws  
7
7.5  
8
(Diagram 7).  
Diagram 3  
Diagram 7  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21  
INSTALLATION  
in Diagram 5 or local codes. Note that for  
steep roof pitches, the vertical height must be  
increased. A poor draft, or down drafting can  
resultfromhighwindconditionsnearbigtrees  
oradjoiningrooflines,inthesecases,increas-  
ing the vent height may solve the problem.  
4) Separatethe2halvesofthewallthimbleand  
securely fasten the one with the tabs to the  
outside wall making sure that the tabs are  
on top and bottom. Fasten the other thimble  
half to the inside wall. The thimble halves  
slip inside each other and can be adjusted  
for 2 x 4 or 2 x 6 walls. The liners must slip  
over the collars a minimum of 1-3/8".  
Note: To make the  
installation more  
aesthetically pleas-  
ing, we recommend  
framing out a square  
to mount the termi-  
nal to.  
7) Ensure vent is vertical and secure the base  
of the flashing to the roof with roofing rails,  
slide storm collar over the pipe section and  
seal with a mastic.  
5) Slip the assembled liner and termination  
assembly through the thimble making sure  
the termination cap faces up (there are  
markings on the cap that show which way  
is up). This will position the termination cap  
with proper down slope for draining water.  
Fasten the cap to the outer wall with the 4  
supplied screws.  
8) Install the vertical termination cap by twist-  
Note: If installing termination on a siding  
covered wall, furring strips must be  
used to ensure that the termination  
is not recessed into the siding.  
locking it.  
Note: Anyclosetsorstoragespaces,which  
the vent passes through must be  
enclosed.  
2) Level the fireplace and fasten it to the fram-  
ing using nails or screws through the nailing  
strips.  
Offset Chart  
6) Pull the centre 4"(100mm) liner and outer  
6-7/8"(175mm) liner out enough to slip over  
the flue collars of the fireplace. (You may  
wish to cut the liner shorter to make it more  
workable.) Do not bend liner more than  
90o.  
3) Assemble the vent assembly by applying  
Mill Pac to the 4"(100mm) inner collar of the  
terminationand slippingthe4"(100mm)liner  
over it at least 1-3/8" (35mm). Fasten with  
the3screws(drillingpilotholeswillmakethis  
easier). Apply Mill Pac or high temperature  
silicone to the 6-7/8"(175mm) flex pipe and  
slip it over the 6-7/8" outer collar of the vent  
terminal at least 1-3/8"(35mm) and fasten  
with the 3 screws.  
7) Apply Mill Pac over the fireplace inner collar  
and slip the 4"(100mm) liner down over it  
and attach with 3 supplied screws.  
8) Do the same with the 6-7/8"(175mm) liner.  
9) Applyabeadofsiliconebetweenthethimble  
and termination and around the outer edge  
of the terminal at the wall in order to keep  
the water out.  
NOTE: Horizontal sections must be sup-  
ported at intervals not exceeding 3  
feet (0.9 meter). (Flame picture and  
performance will be affected by sags  
in the liner).  
IMPORTANT: Do not locate termination  
hood where excessive snow or ice buildup  
may occur. Be sure to check vent termi-  
nation area after snow falls, and clear to  
prevent accidental blockage of venting  
system. When using snow blowers, make  
sure snow is not directed towards vent  
termination area.  
INSTALLATION  
PROCEDURES  
for UltraGlow Direct Vent  
System (Flex)  
1) Locate the unit in the framing, rough in the  
gas (preferably on the right side of the unit)  
and the electrical (Junction block is on the  
left side) on the left. Locate the centerline of  
the termination and mark wall accordingly.  
Cut a 10"(254mm) hole in the wall (inside  
dimension).  
Note: A 1-1/2"(38mm) clearance around  
the liner must be maintained except  
that only a 1" (25mm) clearance is  
needed at the termination end. We  
recommend framing a 10"(254mm)  
x 10"(254mm) (inside dimensions)  
hole to give structural rigidity for  
mounting the termination.  
22  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
The manifold pressure is controlled by a  
regulator built into the gas control, and should  
be checked at the pressure test point.  
For USA installations follow local codes and/or  
the current National Fuel Gas Code, ANSI  
Z223.1.  
G36D-NG System Data  
For 0 to 4500 feet altitude  
Burner Inlet Orifice Sizes:  
#42  
Note:Toproperlycheckgaspressure,both  
inletandmanifoldpressuresshould  
becheckedusingthevalvepressure  
ports on the valve.  
When using copper or flex connectors use only  
approved fittings. Always provide a union so  
that gas lines can be easily disconnected for  
servicing. Flare nuts for copper lines and flex  
connectors are usually considered to meet this  
requirement.  
Max. Input Rating 26,000 Btu/h  
Min. Input Rating 13,100 Btu/h  
Supply Pressure  
min.5.0" w.c.  
1) Make sure the valve is in the "OFF" posi-  
tion.  
Manifold Pressure  
(High)  
Important:Alwayscheckforgasleakswitha  
soapandwatersolutionorgasleakdetector.  
Do not use open flame for leak testing.  
3.8"+/- 0.2"w.c.  
2) Loosen the "IN" and/or "OUT" pressure  
tap(s), turning counterclockwise with a  
1/8" wide flat screwdriver.  
Log Set: Ceramic fibre, 7 per set.  
Vent System: Simpson Dura-Vent Direct  
Vent System or UltraGlow Direct  
Vent System (Flex)  
3) Attach manometer to "IN" and/or "OUT"  
PILOT ADJUSTMENT  
pressure tap(s) using a 5/16" ID hose.  
Periodically check the pilot flames. Correct  
flame pattern has three strong blue flames:  
1 flowing around the thermopile, 1 around  
the thermocouple and 1 flowing across the  
burner (it does not have to be touching the  
burner).  
4) Light the pilot and turn the valve to "ON"  
position.  
G36D-LP System Data  
5) The pressure check should be carried out  
withtheunitburningandthesettingshould  
be within the limits specified on the safety  
label.  
For 0 to 4500 feet altitude  
Burner Inlet Orifice Sizes:  
#53  
Note: If you have an incorrect flame pat-  
tern, contact your Regency dealer  
for further instructions.  
Max. Input Rating 26,000 Btu/h  
Min. Input Rating 13,800 Btu/h  
6) When finished reading manometer, turn  
off the gas valve, disconnect the hose and  
tighten the screw (clockwise) with a 1/8"  
flat screwdriver. Note: Screw should be  
snug, but do not over tighten.  
Supply Pressure  
min.12.0" w.c.  
Manifold Pressure  
(High)  
11"+/- 0.2" w.c.  
S.I.T. VALVE DESCRIPTION  
Log Set: Ceramic fibre, 7 per set.  
Vent System: Simpson Dura-Vent Direct  
Vent System or UltraGlow Direct  
Vent System (Flex)  
1) Gas cock knob  
2) Manual high/low adjustment  
3) Pilot Adjustment  
4) Thermocouple Connection - option  
5) Outlet Pressure Tap  
6) Inlet Pressure Tap  
7) Pilot Outlet  
8) Main Gas Outlet  
9) Alternative TC Connection  
Point  
HIGH ELEVATION  
This unit is approved in Canada for altitude 0  
to 4500 ft. (CAN1 2.17-M91) with the orifice  
supplied.  
Incorrectamepatternwillhavesmall,prob-  
ably yellow flames, not coming into proper  
contact with the rear burner or thermopile  
or thermocouple.  
GAS LINE  
INSTALLATION  
The gas line can be brought through either the  
right or the left side of the appliance. The gas  
valve is situated on the right hand side of the  
unit and the gas inlet is on the right hand side  
of the valve.  
GAS PIPE PRESSURE  
TESTING  
Note: If the gas line is being installed from  
the left side, be sure to leave room to  
accommodate servicing of the fan.  
The appliance must be isolated from the gas  
supply piping system by closing its individual  
manual shut-off valve during any pressure  
testing of the gas supply piping system at test  
pressures equal to or less than 1/2 psig. (3.45  
kPa). Disconnectpipingfromvalveatpressures  
over 1/2 psig.  
The gas line connection may be made of rigid  
pipe, copper pipe or an approved flex connec-  
tor. (If you are using rigid pipe, ensure that the  
valvecanberemovedforservicing.)Sincesome  
municipalities have additional local codes it is  
alwaysbesttoconsultwithyourlocalauthorities  
and the CAN/CGA B149 installation code.  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
INSTALLATION  
CONVERSION KIT FROM NATURAL GAS TO PROPANE MODEL #290-969  
FOR G36D USING SIT 820 NOVA GAS VALVE  
THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER  
IF IN DOUBT DO NOT DO THIS CONVERSION !!  
8) Remove burner orifice with a 1/2" wrench  
and discard. Use another wrench to hold  
on to the elbow behind the orifice.  
Conversion Kit Contains:  
Qty. Part #  
1
Description  
910-018 SIT Conversion Kit-50%  
Turndown LP  
1
1
1
1
1
1
910-037 LP Injector (Pilot Orifice)  
904-345 Burner Orifice #53  
908-255 Decal "Converted to Propane"  
908-528 Red "PROPANE" label  
908-529 5/32" Allen Key  
918-165 Instruction Sheet  
Burner Orifice  
1) Shut off the gas supply.  
9) ReinstallnewburnerorificeLPstamped#53  
and tighten.  
2) Remove the louvers (and bay door if it is  
installed).  
10) Remove and discard the 3 pressure regula-  
tor mounting screws (A), pressure regulator  
tower (B) and diaphragm (C).  
3) Open the flush door and remove the door.  
4) Remove the logs and embers.  
11) Insure that the rubber gasket (D) is properly  
positioned and install the new HI/LO pres-  
sure regulator assembly to the valve using  
the new screws (E) supplied with the kit.  
Tighten screws securely.  
5) Remove the 2 screws holding the Burner  
Assembly to the firebox base. Push the  
Burner Assembly to the left and lift out.  
12) Reverse steps 5) to 2).  
13) Attach clear label "This unit has been con-  
verted to Propane" near or on the serial #  
decal. Attach white label "This valve has  
been converted from NG to LPG using SIT  
conversion Kit Code 0.907.202" onto the  
valve.  
Remove the 2 screws, push Burner  
Assembly to the left and lift out.  
6) Pull off the pilot cap to expose the pilot  
orifice.  
14) Replace yellow "Natural Gas" label with red  
"Propane" label  
15) Check for gas leaks.  
16) Check inlet and outlet pressures.  
17) Check operation of flame control.  
18) Checkforproperameappearanceandglow  
on logs.  
7) Unscrew the pilot orifice with the allen key  
and replace with the LP pilot orifice in the  
kit and replace pilot cap.  
24  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
LOG SET INSTALLATION  
Read the instructions below carefully and refer to the diagrams. If logs are broken do not use the unit until they are replaced. Broken  
logs can interfere with the pilot operation.  
The gas log kit (Part # 780-930) contains the following pieces:  
a) 02-75 Rear Log  
902-277  
902-237  
902-242  
902-239  
902-241  
902-238  
902-240  
b) 02-55 Middle Left Log  
c) 02-50 Front Left Log  
d) 02-53 Center Left Log  
e) 02-51 Front Bottom Log  
f) 02-54 Center Right Log  
g) 02-52 Middle Right Log  
h) Embers  
02-75  
02-51  
902-156  
i) Vermiculite  
902-179  
02-55  
02-52  
02-75  
Bracket  
Bracket  
Notch  
02-51  
Notch  
02-50  
02-53  
02-54  
02-51  
5) Position Log 02-53 across the cutouts in Logs 02-75 and 02-51 with  
The "02" refer numbers (i.e. 02-75) are  
molded into the rear of each log.  
the notch on the left side of the log fitting into the 2nd grate tab.  
1) Carefully remove the logs from the box and unwrap them. The logs  
are fragile, handle with care - do not force into position.  
02-53  
2) Sprinkle the vermiculite all over the top of the base brick panel.  
3) Place Log 02-75 on the rear log support pins with the flat side to the  
02-75  
02-51  
back.  
2nd Grate Tab  
Cutouts  
02-75  
02-51  
02-53  
Support Pins  
4) Place Log 02-51 on the front right side of the burner. Push the back  
of the log against the 2 brackets with the notch on the bottom right  
side of the log fitting into the right side of the grate.  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
8) Place Log 02-52 between Logs 02-51 and 02-75 and on the indenta-  
6) Position Log 02-54 across the cutouts in Logs 02-51 and 02-53. The  
tion on Log 02-54. The bottom right end sits behind the rear grate  
tab.  
notch in the bottom right end fitting against the 5th grate tab.  
02-75  
02-52  
02-54  
02-51  
02-53  
02-51  
02-54  
Log indentation  
Photo shows rear grate tab. Log  
02-51 was removed to show the posi-  
02-52  
tioning of Log 02-52.  
02-54  
Rear  
Grate Tab  
02-54  
5th Grate Tab  
9) Sit Log 02-50 on the front left side of the burner. Push the back of  
the log against the 2 front brackets with the notch on the bottom of  
the log fitting into the first grate tab.  
7) Place the bottom left front edge of Log 02-55 against the rear bracket  
on the burner tray and rest the log on the cutout on Log 02-53.  
02-75  
02-50  
02-55  
02-53  
02-51  
02-53  
Front Brackets  
02-55  
Rear Bracket  
Cutouts  
02-50  
Notch  
02-53  
26  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
10) Place the embers on the front of the burner tray in the places shown  
11) Test fire to ensure proper light off (make sure flame flows smoothly  
from one end of burner to the other). If there is any flame hesitation,  
check that area for any blockage of the burner ports.  
on the photos below.  
12) Install flush glass as per instructions in manual.  
Place embers in these 3 locations  
on the burner tray.  
02-51  
02-54  
Do not block the burner holes in this area  
adjacent to the Log 02-54  
02-75  
02-55  
02-51  
02-50  
02-54  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
Use the hook to pull the spring out until you  
can put the hook into the slot on the bottom  
door bracket. Repeat for 2nd spring. See  
diagram 3.  
Flush Louvers  
STANDARD FLUSH  
DOOR  
The standard flush door comes with a black  
frame. To install the frame, simply hook the top  
door flange onto the top of the unit and swing  
the door towards the unit, diagram 1.  
1) Install each top by clipping the louver lip  
onto the top louver brackets ensuring that  
each individual louver is centered from side  
to side.  
2) The bottom louver has a hinge that is at-  
tached (2 screws per hinge) to the lip on  
bottom of the unit.  
3) Open the bottom louver. Pull the Burner  
ON/OFF control box from inside the bottom  
of the fireplace and position the slots in the  
bracket over the 2 screws on the left side  
of the bottom louver. Push down to lock into  
place. Tighten the screws.  
Diagram 3  
To remove the flush door, reverse the above  
steps.  
Optional Flush Trim  
Attach the round magnets to the back of the top  
trim piece and to the bottom trim piece, then at-  
tach trim to the top and bottom of Flush door.  
Diagram 1  
Note: Top and bottom louvers are  
different.  
Be careful that the glass gasket does not roll up;  
there must be a gap between the gasket and  
the door lip to ensure that the door sits securely  
on the unit. Diagram 2.  
Diagram 2  
28  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
Option 1:  
REMOTE CONTROL  
Option 3:  
WALL THERMOSTAT  
Option 2:  
WALL SWITCH  
A wall thermostat may be installed if desired,  
connect the wires as per the wiring diagram.  
Use the table below to determine the maximum  
wire length.  
1) Runthewirethroughtherightorleftsideinlet  
UsetheUltraGlowRemoteControlKit approved  
for this unit. Use of other systems may void  
your warranty.  
opening. Be careful not to damage wire.  
Note: We recommend a maximum of 15'  
of wire but if you wish to go with a  
longer run, use the Thermostat Wire  
Table.  
Note:Preferableifthethermostatisinstalled  
on an interior wall.  
The remote control kit comes with a hand held  
transmitter, a receiver and a wall mounting  
plate.  
UltraGlow offers an optional programmable  
thermostat or basic wall thermostat but any  
250-750 millivolt rated non-anticipator type  
thermostat that is CSA, ULC or UL approved  
may be used.  
2) Connectthewiretothewallswitchandinstall  
1) Choose a convenient location on the wall  
to install the receiver and the receptacle  
box (protection from extreme heat is very  
important). Run wires from the fireplace  
to that location. Use the Thermostat Wire  
Table.  
into the receptacle box.  
CAUTION  
Do not connect millivolt  
wall switch wire to a 120V wire.  
CAUTION  
Do not connect millivolt  
wall thermostat wires  
to a 120V wire.  
2) Connect the two wires to the gas valve. See  
diagram below.  
Thermostat Wire Table  
Recommended Maximum Lead Length  
(Two-Wire) When Using Wall  
Thermostat (CP-2 System)  
Wire Size  
Max. Length  
CAUTION  
14 GA.  
16 GA.  
18 GA.  
20 GA.  
22 GA.  
50 Ft.  
32 Ft.  
20 Ft.  
12 Ft.  
9 Ft.  
Do not connect millivolt remote  
control wires to a 120V wire.  
3) Install3AAAalkalinebatteriesintransmitter  
and 4 AA alkaline batteries in the receiver.  
Install the receiver and its cover in the wall.  
Switch the remote receiver to "remote"  
mode. The remote control is now ready for  
operation.  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
29  
INSTALLATION  
WIRING DIAGRAM  
This heater does not require a 120VA.C. supply for operation. In case of a power failure, the burner switch and the optional remote control/thermostat  
will continue to operate.  
(Do not cut the ground terminal off under any circumstances.)  
Caution: Ensure that the wires do  
not touch any hot surfaces and are  
away from sharp edges.  
CAUTION: Label all wires prior  
to disconnection when servic-  
ing controls. Wiring errors can  
cause improper and dangerous  
30  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION  
INSTALLING THE OPTIONAL FAN  
120 Volt AC power is needed for the fan switch  
and blower. Athree wire power cord is provided  
to be plugged into the receptacle.  
Note: A 120 Volt AC power cord can be in-  
stalled at rough-in stage so that the  
powerisavailable.Athreewirepower  
cord can be used.  
To Remove the Fan  
1) Shut the power off.  
2) Reverse the above instructions.  
Unit must be grounded at all times. Do  
not cut the ground terminal off under any  
circumstances.  
5) If the left spring was unhooked in step 3),  
hook it back into the bracket. Take care not  
toclipanywires.Attachtheadhesivebacked  
wire holder clip (Part #910-199) onto the  
stove base.  
Note: The bearings are lubricated for life.  
Do not lubricate them. Make sure  
you vacuum the fan area on a regular  
basis.  
1) Shut the power off.  
2) Open the bottom louver door.  
3) Slide the fan in towards the rear of the unit  
and slip it over the two mounting studs.  
Ensure that the fan blades do not rub  
against the valve tubing.  
Optional: If you require extra space to slide the fan to the back, the left spring can be unhooked  
from the bracket.  
4) Plug the fan to the receptacle as shown in  
the wiring diagram below.  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING INSTRUCTIONS  
2) Turn gas control knob so indicator points  
OPERATING  
INSTRUCTIONS  
to "OFF" position and allow 5 minutes for  
any gas in the combustion chamber to  
escape.  
DO NOT BURN THE APPLIANCE  
WITHOUT THE GLASS FRONT IN  
PLACE.  
During the first few fires, a white film  
1) Read and understand these instructions  
3) Turn gas control knob counterclockwise  
so indicator points to the "PILOT" position.  
Depressthegascontrolknobfully.Depress  
the igniter button several times until the  
pilotlights.Afterapproximatelyoneminute,  
releasethegascontrolknob.Thepilotame  
should continue to burn. If the pilot does  
not remain lit, repeat operation allowing a  
longer period before releasing gas control  
knob.  
may develop on the glass front as part  
of the curing process. The glass should  
be cleaned or the film will bake on and  
become very difficult to remove. Use a  
non-abrasive cleaner and NEVER clean  
the glass while it is hot.  
before operating this appliance.  
2) Check to see that all wiring is correct and  
enclosed to prevent possible shock.  
3) Check to ensure there are no gas leaks.  
4) Make sure the glass in the door frame is  
properly positioned. Never operate the ap-  
pliance with the glass removed.  
AERATION  
4) When the pilot stays lit, turn the gas knob  
further counterclockwise to the "ON" posi-  
tion.  
ADJUSTMENT  
5) Verify that the venting and cap are unob-  
structed.  
The air shutter can be adjusted by moving the  
adjustingwireupordown.Thewireisaccessed  
through the bottom louver opening. Open the  
air shutter for a blue flame or close for a yel-  
lower flame. The burner aeration is factory set  
but may need adjusting due to either the local  
gas supply or altitude.  
6) Ensure that the brick panels are installed.  
5) Use the wall switch, thermostat or remote  
control to turn on the unit.  
7) Verify log placement. If the pilot cannot be  
seen when lighting the unit, the logs have  
been incorrectly positioned.  
6) Rotate the flame height regulator to adjust  
the flame height higher or lower.  
8) The unit should never be turned off, and on  
again without a minimum of a 60 second  
wait.  
Minimum Air Shutter Opening:  
3/16"  
1/2"  
Natural Gas  
Propane  
SHUTDOWN  
PROCEDURE  
CAUTION:Carbonwillbeproducedifairshutter  
is closed too much.  
1) Use the wall switch, thermostat or remote  
control to turn off the main burner.  
Note: Any damage due to carboning  
resulting from improperly setting  
theaerationcontrolsisNOTcovered  
under warranty.  
2) Turn the main gas control clockwise to the  
"OFF" position to turn off the pilot.  
3) Turn off all electric power to appliance if  
Note: AerationAdjustmentshouldonlybe  
performedbyanauthorizedRegency  
Installer at the time of installation or  
service.  
service is to be performed.  
FIRST FIRE  
LIGHTING  
Therstreinyourstoveispartofthepaintcur-  
ing process. To ensure that the paint is properly  
cured, it is recommended that you burn your  
fireplace for at least four (4) hours the first time  
before you use it with the fan on.  
PROCEDURE  
IMPORTANT  
To ignite or reignite the pilot,  
you must first release the ten-  
sion springs below the door.  
When first operated, the unit will release an  
odour caused by the curing of the paint, the  
burning off of any oils remaining from manufac-  
turing. Smoke detectors in the house may go  
off at this time. Open a few windows to ventilate  
the room for a couple of hours.  
Adjustment Wire: push to close or  
pull to open aeration cap.  
Only when the pilot holds, without pressure  
being applied to the control knob, reapply the  
tension springs to the door. The unit must  
not be operated with the tension springs  
unattached.  
Closed - Tall yellow  
Open - Short Blue  
The glass panel may require cleaning after the  
unithascooleddown. DONOTATTEMPT  
TO CLEAN THE GLASS WHILE IT  
IS HOT.  
IMPORTANTGascockknobcannotbeturned  
from "PILOT" to "OFF" unless it is partially  
depressed.  
Note: When the glass is cold and the appli-  
anceislit,itmaycausecondensation  
andfogtheglass.Thiscondensation  
is normal and will disappear in a few  
minutes as the glass heats up.  
1) Turn burner OFF using "ON/OFF" switch.  
32  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATING INSTRUCTIONS  
Copy of the Lighting Plate Instructions  
NORMAL OPERATING  
SOUNDS OF GAS  
APPLIANCES  
It is possible that you will hear some sounds  
fromyourgasappliance.Thisisperfectlynormal  
due to the fact that there are various gauges  
and types of steel used within your appliance.  
Listedbelowaresomeexamples.Allarenormal  
operatingsoundsandshouldnotbeconsidered  
as defects in your appliance.  
Burner Tray:  
The burner tray is positioned directly under the  
burner tube(s) and logs and is made of a differ-  
ent gauge material from the rest of the firebox  
and body. Therefore, the varying thicknesses of  
steelwillexpandandcontractatslightlydifferent  
rates which can cause "ticking" and "cracking"  
sounds. You should also be aware that as there  
are temperature changes within the unit these  
sounds will likely re-occur. Again, this is normal  
for steel fireboxes.  
Pilot Flame:  
While the pilot flame is on it can make a very  
slight "whisper" sound.  
Gas Control Valve:  
As the gas control valve turns ON and OFF, a  
dullclickingsoundmaybeaudible,thisisnormal  
operation of a gas regulator or valve.  
Unit Body/Firebox:  
Different types and thicknesses of steel will  
expand and contract at different rates resulting  
in some "cracking" and "ticking" sounds will be  
heard throughout the cycling process.  
MAINTENANCE  
INSTRUCTIONS  
1) Alwaysturnoffthegasvalvebeforecleaning.  
For relighting, refer to lighting instructions.  
Keep the burner and control compartment  
clean by brushing and vacuuming at least  
once a year. When cleaning the logs, use a  
soft clean paint brush as the logs are fragile  
and easily damaged.  
2) Clean appliance and door with a damp  
cloth (never when unit is hot). Never use  
an abrasive cleaner. The glass should be  
cleaned with a gas fireplace glass cleaner.  
The glass should be cleaned when it  
starts looking cloudy.  
3) The heater is finished in a heat resistant  
paintandshouldonlyberefinishedwithheat  
resistant paint. UltraGlow uses StoveBright  
Paint - Metallic Black #6309.  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
33  
MAINTENANCE  
4) Make a periodic check of burner for proper  
position and condition. Visually check the  
flameoftheburnerperiodically,makingsure  
the flames are steady; not lifting or floating.  
If there is a problem, call a qualified service  
person.  
Clean any fingerprints off before turning the  
unit on. If the top louvers start to discolour,  
check the door gasket seal and replace if  
necessary.  
WARNING:Donotoperatetheappliance  
withtheglasspanelsremoved,cracked  
or broken. Replacement of the glass  
panels should be done by a licensed  
or qualified service person.  
LOG REPLACEMENT  
5) The appliance and venting system must be  
inspected before use, and at least annually,  
byaqualifiedeldserviceperson,toensure  
that the flow of combustion and ventilation  
air is not obstructed.  
Caution: Wear gloves when removing  
damaged or broken glass.  
The unit should never be used with broken logs.  
Turn off the gas valve and allow the unit to cool  
before opening door and carefully remove the  
logs. (The pilot light generates enough heat to  
burn someone.) If for any reason a log should  
need replacement, you must use the proper  
replacement log. The position of these logs  
must be as shown in the diagrams under Log  
Installation.  
Flush Glass Replacement  
Removetheushdoorfront(asperinstructions  
onpage28).Removethe4glassclipsfromeach  
corner.Slideinthenewreplacementglass.Push  
the4glassclipsbackontotheframe. Theglass  
must have gasketing around it.  
Note: Never operate the appliance with-  
out the glass properly secured in  
place.  
6) Donotusethisapplianceifanyparthasbeen  
under water. Immediately call a qualified  
service technician to inspect the appliance  
andtoreplaceanypartofthecontrolsystem  
and any gas control which has been under  
water.  
Note: Improperpositioningoflogsmaycre-  
ate carbon build-up and will severely  
alter the unit's performance which is  
not covered under warranty.  
7) Verify operation after servicing.  
THERMOPILE/  
THERMOCOUPLE  
General Vent Maintenance  
1) Open the bottom louvers.  
Conduct an inspection of the venting system  
semi-annually.Recommendedareastoinspect  
as follows:  
2) Loosenthethermocoupleorthermopilewith  
a 7/16" wrench.  
1) Check the Venting System for corrosion in  
areas that are exposed to the elements.  
These will appear as rust spots or streaks,  
and in extreme cases, holes. These com-  
ponents should be replaced immediately.  
3) Disconnect thermocouple by loosening nut  
from the valve with a 9mm wrench. Dis-  
connect thermopile by loosening 2 screws  
marked TP on the valve.  
4) Drop the thermocouple or thermopile down  
2) Remove the Cap, and shine a flashlight  
down the Vent. Remove any bird nests, or  
other foreign material.  
from the bracket and pull it out of the unit.  
5) Reinstall the new ones in reverse order.  
3) Checkforevidencesofexcessivecondensa-  
tion, such as water droplets forming in the  
innerliner,andsubsequentlydrippingoutthe  
joints, Continuouscondensationcancause  
corrosion of caps, pipe, and fittings. It may  
becausedbyhavingexcessivelateralruns,  
toomanyelbows,andexteriorportionsofthe  
system being exposed to cold weather.  
GLASS GASKET  
If the glass gasket requires replacement use  
a tadpole glass gasket for the Flush Front (Part  
# 936-155).  
4) Inspectjoints, toverifythatnopipesections  
or fittings have been disturbed, and conse-  
quently loosened. Also check mechanical  
supports such as Wall Straps, or plumbers'  
tape for rigidity.  
DOOR GLASS  
Your UltraGlow stove is supplied with high tem-  
perature,5mmtemperedglassthatwillwithstand  
the highest heat that your unit will produce. If  
your glass requires cleaning, we recommend  
using an approved glass cleaner available at all  
authorized dealers. Do not use abrasive materi-  
als. Do not clean the glass when hot.  
GOLD-PLATED  
OR BRASS TRIM  
The 24 carat gold plated or brass finish on the  
trim requires little maintenance, and need only  
be cleaned with a damp cloth. DO NOT use  
abrasivematerialsorchemicalcleaners,asthey  
may harm the finish and void the warranty.  
In the event that you break your glass by impact,  
purchase your replacement from an authorized  
UltraGlow dealer only, and follow our step-by-  
step instructions for replacement.  
34  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
11) Removethe12Phillipsheadscrewssecuring  
REMOVING VALVE  
1) Shut off the gas supply.  
2) Remove louvers.  
INSTALLING VALVE  
the valve tray assembly in place.  
1) Attach the valve to the valve bracket with  
the 4 (m5x8 metric) screws provided.  
2) Reconnect the "gas out" flare fitting with an  
3) Open and remove the flush door.  
4) Remove logs.  
11/16" wrench.  
3) Reconnect the "gas out" flare nut with a  
13/16" wrench.  
5) Remove the burner assembly by removing  
the two Phillips head screws.  
4) Install piezo ignitor push button assembly  
and reconnect wire.  
Valve Tray Assembly  
screws  
5) Reconnectthequickdropoutthermocouple  
nut with a 9mm wrench.  
12) Lift the entire assembly out.  
6) Reconnect the pilot tube nut with a 7/16"  
wrench.  
7) Scrapeofftheoldgasketfromtheoorofthe  
firebox and from the valve tray assembly.  
8) Install a new gasket and reinstall the valve  
6) Remove the burner assembly by sliding left  
tray assembly.  
and out.  
Note: Failure to install a new gasket may  
severely affect the appliance per-  
formance.  
9) Reinstall the 12 hold down screws.  
10) Hook up the 2 TP and 2 TH wires to the  
appropriate connections on the valve.  
7) Remove the rear log stand by removing the  
11) Reinstall the bottom brick panel and the  
2 screws.  
front log stand.  
Rear Log Stand  
Screws  
12) Install burner assembly  
13) Undo the pilot tube from the valve with a  
13) Hook up the gas line and check for gas  
leaks with a soap and water solution or a  
gas leak detector. (Do not use open flame  
for leak testing.)  
7/16" wrench.  
14) Undo the quick drop out thermocouple nut  
on the valve with a 9mm (metric) wrench.  
14) Fire up the unit temporarily  
15) Remove the Piezo ignitor wire and push  
button assembly.  
15) Check the manifold pressure.  
16) Undo the "gas out" flare nut with a 13/16"  
16) Reinstall the logs and base panels as  
wrench.  
needed.  
8) Lift out the bottom base panel.  
17) Undo the "gas out" flare fitting with an 11/16"  
17) Close the door and replace the louvers.  
wrench.  
18) Fire up the unit again and check for proper  
18) Remove the 4 Phillips head screws from  
the sides of the valve bracket and remove  
valve.  
flame appearance and glow on logs.  
Hint:  
If you are using black pipe, ensure  
that there is a union by the valve,  
otherwise removal will be almost  
impossible.  
Verify proper operation  
after servicing.  
9) Disconnect the inlet gas line.  
10) Disconnect the 2 TP wires and the 2 TH  
wires from the valve.  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
35  
PARTS LIST  
G36D MAIN ASSEMBLY  
Part #  
Description  
Part #  
Description  
1) 948-253 Door Handle  
2) 510-026 Hinge Bracket - Left/Right  
3) 948-045 Chain  
27)  
28)  
29)  
30)  
34)  
35)  
*
*
*
*
*
*
Outer Flue Collar  
Inner Flue Collar Assy  
Flue Mounting Plate  
Gasket for Flue Collar  
Firebox Tray  
4) 948-115 Spring  
6) 430-129 Receptacle Box Mount  
7) 910-429 Box - Receptacle  
8) 910-428 Duplex Receptacle  
9) 910-430 Cover - Receptacle  
10) 904-687 Clamp Connector  
Thermodisc Bracket  
910-882 Wire-Harness-Valve to Burner  
331-917 Fan & Speed Control Assy  
(120 Volts) Optional  
20) 510-033 Top Nailing Strip  
21) 510-064 Side Nailing Strip  
42) 910-331/P Fan Motor  
50) 510-994 Optional Rigid Pipe Adaptor  
101) 690-022 Cover Plate - Outer Box Side  
23) 780-011 Standoff - Top  
24) 780-013 Standoff - Side/Back  
918-156 Manual  
290-969 Conversion Kit - NG to LP  
*Not available as a replacement part.  
36  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS LIST  
G36D BURNER ASSEMBLY & LOG SET  
Description  
Part #  
52) 910-190  
Piezo Ignitor & Nut  
53) 780-021  
786-574/P  
786-576/P  
Gasket - Valve Access Plate NG/LP  
Valve Assy - Natural Gas  
Valve Assy - Propane  
56)  
*
Valve Tray - NG/LP  
57) 910-378  
910-380  
Valve - S.I.T. - Natural Gas  
Valve - S.I.T. - Propane  
Valve Bracket  
58)  
*
65)  
*
Pilot Bracket  
66) 910-038  
910-039  
Pilot Assy - S.I.T. - 3 Flame NG  
Pilot Assy - S.I.T. - 3 Flame LP  
Pilot Holder  
67)  
*
68) W840470  
904-430  
Pilot Assembly Gasket  
Orifice #42 - Natural Gas  
Orifice #53 - Propane  
Orifice Gasket  
904-345  
936-170  
69)  
*
Firebox Base  
75)  
76)  
*
*
Deflector - Left  
Deflector - Right  
79) 786-525  
Burner Assy - NG/LP  
83)  
*
Rear Log Support Bracket  
Log Set  
85) 780-930  
86)  
*
Pilot Deflector  
*Not available as a replacement part.  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS LIST  
G36D FLUSH FRONT ASSEMBLY  
Part #  
Description  
131) 510-934 Flush Glass Trim (Set) - Brass  
510-947 Flush Glass Trim (Set) - Steel  
510-932 Flush Glass Trim (Set) - Gold  
132) 904-196 Magnet (1" Round)  
133) 780-069 Flush Louver - Top - Black  
134) 786-520 Assembly - Bottom - Black  
135) 940-334/P Glass - Tempered  
137) 904-691 U-Clip  
139) 936-155 Glass Gasket (Tadpole)  
140) 948-042 Spring Hinge - Black  
*Not available as a replacement part.  
38  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY  
UltraGlow products, are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully  
inspects each unit thoroughly before it leaves our door. UltraGlow is pleased to extend this one year warranty to the original purchaser  
of a UltraGlow product. This warranty is not transferable.  
The Warranty: One Year  
Covered under the agreement are the following components: Combustion chamber, heat exchanger, burner tubes, logs, embers, glass (thermal  
breakage) and all gold plating (against defective manufacture).  
The above will be covered for parts and labour for one year. Electrical components such as blowers, fan motor, switches, wiring, thermodiscs,  
remote control, thermopiles, thermocouples, pilot assemblies, and gas valves are covered for one year from the date of purchase.  
Conditions:  
Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at FPI's option, through an accredited  
distributor or agent provided that the defective part be returned to the distributor or agent Transportation Prepaid, if requested.  
It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned  
to FPI and evaluated for manufacturer defect.  
The authorized selling dealer is responsible for all in-field service work carried out on your FPI product. FPI will not be liable for results or costs of  
workmanship from unauthorized service persons or dealers.  
At all times FPI reserves the right to inspect product in the field which is claimed to be defective.  
All claims must be submitted to FPI by authorized selling dealers. It is essential that all submitted claims provide all of the necessary information  
including customer name, purchase date, serial #, type of unit, problem, and part or parts requested, without this information the warranty will be  
invalid.  
Exclusions:  
This Warranty does not extend to or include paint, door or glass gasketing or trim.  
At no time will FPI be liable for any consequential damages which exceed the purchase price of the unit. FPI has no obligation to enhance or modify  
any unit once manufactured. ie. as products evolve, field modifications or upgrades will not be performed.  
FPI will not be liable for travel costs for service work.  
Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this  
warranty policy.  
Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy.  
The warranty will not extend to any part which has been tampered with or altered in any way, or in our judgment has been subject to misuse,  
improper installation, negligence or accident, spillage or downdrafts caused by environmental or geographical conditions, inadequate ventilation,  
excessive offsets, negative air pressure caused by mechanical systems such as furnaces, fans, clothes dryer, etc.  
Freight damage to stoves and replacement parts is not covered by warranty and is subject to a claim against the freight carrier by the dealer.  
FPI will not be liable for acts of God, or acts of terrorism, which cause malfunction of the appliance.  
Performance problems due to operator error will not be covered by this warranty policy.  
Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorization from  
FPI, may nullify your warranty on this product.  
Simpson Dura-Vent venting components are covered by Simpson Dura-Vent Inc. warranty.  
Any alteration to the unit which causes sooting or carboning that results in damage to the interior / exterior facia is not the responsibility of FPI.  
* Subsidy according to job scale as predetermined by FPI.  
UltraGlow G36D Zero Clearance Direct Vent Gas Fireplace  
Download from Www.Somanuals.com. All Manuals Search And Download.  
39  
Register your UltraGlow online at  
Installer: Please complete the following information  
Dealer Name & Address:______________________________________________  
___________________________________________________________________  
Installer: ___________________________________________________________  
Phone #: ___________________________________________________________  
Date Installed: ______________________________________________________  
Serial No.:__________________________________________________________  
© Copyright 2006, FPI Fireplace Products International Ltd. All rights reserved.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Printed in Canada  

Radio Shack Welding System 22 508 User Guide
Raypak Network Card C 5 User Guide
RCA Universal Remote RCU300 User Guide
Riccar Vacuum Cleaner RC 1100 User Guide
Roland Drums TD 9KX User Guide
Samsung Oven BT62CDBFST User Guide
Samsung Printer ML 4550 User Guide
Sanyo CRT Television DS27425, DS32225 User Guide
Sanyo Portable CD Player cdp 195 User Guide
Seiko Group Printer BP 6000 User Guide