EBZ3050RH
848-L2C-93A0 (909)
U
S
OWNER'S/OPERATOR'S
MANUAL
BACKPACK BLOWER
EBZ3050RH
WARNING
The engine exhaust from this
product contains chemicals
known to the State of California to
cause cancer, birth defects or
other reproductive harm.
WARNING
Before using our products,
please read this manual carefully
to understand the proper use of
your unit.
APPLICABLE SERIAL NUMBERS :
90100101 and up
US-1
Download from Www.Somanuals.com. All Manuals Search And Download.
EBZ3050RH
1. Parts location
U
S
1. Frame
2. Shoulder Strap
3. Spark Plug Cap
4. Throttle Lever
5. Net
6. Choke Lever
7. Air Cleaner
8. Volute Case
9. “CAUTION” Label
10. Elbow
11. Fuel Tank
12. Recoil Starter
13. Ignition Switch
14. Engine Cover
2. Specifications
■ MODEL EBZ3050RH
Dimensions (L x W x H) mm (in) ···············································································313x394x420 (12.3x15.5x16.5)
Dry Weight kg (lbs)······································································································································6.2 (13.7)
Fuel Tank Capacity liter (fl. oz)··················································································································1.08 (36.5)
Engine Type··········································································································Air cooled 2-cycle gasoline engine
3
Piston Displacement cm (cu. in)···············································································································29.5 (1.80)
Air Filter··················································································································································Dry Urethane
Carburetor (Diaphragm) valve type··················································································································Rotary
Ignition System····················································································································································C.D.I
Spark Plug························································································································NGK CMR7H (Noise-proof)
Muffler ·································································································································Spark arrester equipped
Operating Engine Speed rpm ················································································································3000 to 6500
Fuel Consumption liter/h (fl. oz/h) ·············································································································0.58 (19.6)
Average Air Volume (w/std Pipe) cu. m/min (cfm)······················································································10.7 (378)
Max. Air Volume (w/o Pipe) cu. m/min (cfm) ······························································································13.1 (463)
Max. Air Velocity m/sec (mph)····················································································································57.4 (128)
Emission Compliance Period hrs.·························································································································300
Noise Level (50 Feet ANSI B175.2-2000) dB(A) ·····································································································68
Specifications are subject to change without notice.
US-3
Download from Www.Somanuals.com. All Manuals Search And Download.
EBZ3050RH
3. Warning labels on the machine
(1) Read owner's manual before operating this machine.
(2) Wear head, eye and ear protection.
(3) Handling this machine improperly could result in
accidents causing serious injury or death. Read this
manual carefully and practice using the blower until you
are fully acquainted with all operations and have learned
to use it correctly.
(4) Severing of fingers or hand by fan blade.
Do not open or remove safety guards or nets while engine
is running.
(5) Thrown or blown object.
Stay a safe distance from the machine.
(6) Hot surface
Avoid contact the hot surface during and immediately
operation.
IMPORTANT
(6)
If warning label peel off or become soiled and impossible to read,
you should contact the dealer from which you purchased the
product to order new labels and affix them in the required
location(s).
WARNING
Never modify your machine.
We won't warrant the machine, if you use the remodeled
machine or you don't observe the proper usage written in the
manual.
4. Symbols on the machine
For safe operation and maintenance, symbols
■ EMISSION CONTROL
are carved in relief on the machine. According
to these indications, please be careful not to
make a mistake.
An emission control label is located on the machine.
EMISSION CONTROL INFORMATION
THIS ENGINE MEETS U.S. EPA AND CALIFORNIA
1
EXH/EVP REGS FOR 2009* S.O.R.E.
(a) The port to refuel the "MIX GASOLINE"
Position: Fuel tank cap
2
ENGINE FAMILY : 9HQZS.0294BK* DISPL.: 29cc
3
EMISSION CONTROL SYSTEM : EXH;EM/EVP;SP*
(b) The direction to close the choke
Position: Air cleaner body
COMPLIANCE PERIOD : 300 HOURS
REFER TO OPERATOR'S MANUAL FOR MAINTE-
NANCE, SPECIFICATIONS AND ADJUSTMENTS.
MANUFACTURED:
(c) The direction to open the choke
Position: Air cleaner body
USE JASO FD OR ISO L-EGD GRADE 50:1 OIL
*1: The year will be changed every year of manufacturing.
*2: The initial number will be changed every year of
manufacturing.
*3: SP : Sealed tank made of HDPE or PE.
US-4
Download from Www.Somanuals.com. All Manuals Search And Download.
EBZ3050RH
5. For safe operation
WARNING
3. The ignition system of your unit produces
an electromagnetic field of a very low
intensity. This field may interfere with some
pacemakers. To reduce the risk of serious
or fatal injury, persons with pacemaker
should consult their physician and the
pacemaker munufacturer before operating
this tool.
4. Do not allow other persons to be near the
blower when starting. Keep bystanders
and animals out of the work area.
Children, pets and bystanders should be a
minimum of 50 feet (15 meters) away
when you operate the blower.
5. Avoid using the blower where stable
footing and balance are not assured.
6. All blower service, other than the items
listed in the Owner's Manual, should be
performed by competent service
personnel. (E.g., if improper service to the
blower fan and muffler could cause a
hazardous failure.)
• The blower is used for blowing away
leaves and other debris on the ground.
When operating the blower, the
operater must stand with both feet
firmly on the ground.
Do not operate the blower while
standing on a ladder or a stand.
• Under no circumstances may the
design of the machine be modified
without the permission of the
manufacturer. Always use genuine
accessories and parts. Non-authorized
modifications and/or accessories or
parts can result in serious personal
injury or the death of the operator or
others.
• When planning your work schedule,
allow plenty of time to rest. Limit the
amount of time over which the product
is to be used continuously to
U
S
7. Always shut off the engine before setting it
down.
somewhere around 30 ~ 40 minutes per
session. Also try to keep the total
amount of work performed in a single
day under 2 hours or less.
8. Operate the blower only in well ventilated
areas. Never start or run the engine inside
a closed room or building and potentially
explosive atmosphere. Exhaust fumes
contain dangerous carbon monoxide.
9. Never to touch the spark plug or plug cord
while the engine is in operation. Doing so
may result in being subjected to an
electrical shock.
10. Never to touch the muffler, spark plug,
other metallic parts of the engine or
engine cover while the engine is in
operation or immediately after shutting
down the engine. These metallic parts
and engine cover reach high
■ Basic safety rules
1. Never operate a blower when you are
fatigued, ill, or upset, or under the
influence of madication that may make you
drowsy, or if you are under the influence of
alcohol or drugs.
2. Wear the following protective equipments
when operating the blower.
a: Approved ear protection to reduce the
risk of hearing loss.
b: Approved (ANSI Z87.1.) eye protection
and foot protection to reduce the risk of
injury associated with thrown objects.
c: Face filter mask in dusty conditions to
reduce the risk of injury associated with
the inhalation of dust.
d: Wear sturdy rubber-soled shoes or
shoes with some other form of anti-slip
protection to help protect you against
falling.
temperatures during operation and doing
so could result in serious burns.
11. To reduce the risk of injury associated
with contacting rotating parts, stop the
engine before installing or removing
attachments. Do not operate without net
in place. Always disconnect the spark
plug before performing maintenance or
accessing movable parts.
e: Wear thick anti-vibration gloves to
reduce the risk of whitefinger disease.
f: Do not wear loose clothing, scarves,
neck chains, unconfineed long hair, and
like to reduce the risk of injury
■ Before use
1. Each time before starting the engine,
inspect the entire unit to see if every part is
in good order and is securely tightened in
place. If any damage is found in the fuel
line, the exhaust line, or the ignition wiring,
do not use the blower until it has been
repaired.
associated with objects being drawn into
air intake and rotating parts.
Personal protective equipment cannot
eliminate the risk of injury but it will reduce
the degree of injury.
US-5
Download from Www.Somanuals.com. All Manuals Search And Download.
EBZ3050RH
5. For safe operation
If a breakdown has occurred, do not
operate the blower until the problem is
fixed.
4. After using blowers and other equipment,
CLEAN UP! Dispose of debris in trash
receptacles.
WARNING
2. Before starting operation, always make
sure to check if any obstacles are left
inside the volute case and net. The
obstacles may cause damage on fan
and volute case and serious injury.
3. Check to see if the shock-absorbing
rubber mount has become cracked or
otherwise damaged. Note that failing to
replace this rubber mount when it has
become cracked or damaged may
cause the engine to come loose from its
frame during use, thus resulting in
possible serious bodily injury. If
cracked, be sure to replace without
delay.
■ Transport
1. Drain the fuel from the fuel tank before
transporting or storing the blower.
2. Secure the unit carefully to prevent
movement when it is transported.
3. A unit that receives a strong shock during
transport and unloading may malfunction.
■ Fuel safety
1. Always use caution when handling fuel.
It is highly flammable. Wipe up all spills
and then move the blower at least 10 feet
(3 meters) from the fueling point before
starting the engine.
2. Eliminate all sources of sparks or flame
(i.e. smoking, open flames, or work that
can cause sparks) in the areas where fuel
is mixed, poured, or stored.
3. Do not smoke while handling fuel or while
operating the blower.
4. Do not refuel a hot engine.
5. Do not refuel a running engine.
6. Keep the handles dry, clean and free of oil
or fuel mixture.
7. Always store fuel in an approved container
designed for that purpose.
4. Check the work area that the blower will
be used in and remove or cover all
valuables that may be damaged by the
air blast or thrown debris.
■ Using the product
1. To reduce the risk of injury associated with
thrown objects.
a: Watch out for children, pets, open
windows or freshly washed cars, and
blow debris safely away.
b: Use the full blower nozzle extension so
the air stream can work close to the
ground.
c: Do not allow bystaders in work area.
d: Do not point the blower tube in the
direction of people or pets.
e: Always check to be sure that no debris
has been blown onto someone else's
property.
f: Pay attention to the direction of the
wind, do not work against the wind.
g: Never point a blower tube toward an
open flame to avoid the possibility of
igniting the unit, causing injury to
yourself or damage to surroundings.
■ Storage
1. Always store the blower and fuel so that
there is no risk of leakages or fumes
coming into contact with sparks or naked
flames from electrical equipment, electric
moters, relays/switches, boilers and the
like.
2. For longer period of storage, the fuel tank
should be emptied.
3. When storing the blower, choose a space
indoors free from moisture and out of the
reach of children.
2. To minimize blowing time.
a: Use rakes and brooms to loosen debris
before blowing.
b: In dusty conditions, slightly dampen
surfaces.
■ Avoid noise problem
c: Conserve water by using power blowers
instead of hoses for many lawn and
garden applications, including areas
such as gutters, screens, patios, grills,
porches and gardens.
IMPORTANT
Check and follow the local regulations as to
sound level and hours of operations
for blower.
1. Operate power equipment only at
reasonable hours not early in the morning
or late at night when people might be
disturbed. Comply with times listed in local
3. If you detect abnormal vibration or noise
during operaion, promptly stop the blower
and check whether something has broken.
US-6
Download from Www.Somanuals.com. All Manuals Search And Download.
EBZ3050RH
5. For safe operation
ordinances.
fasteners and rusted or damaged parts.
2. To reduce sound levels, limit the number of
Use special care around the fuel line, the
muffler, and the ignition wiring.
pieces of equipment used at any one time.
3. Operate power blowers at the lowest
possible throttle speed to do the job.
4. Check your equipment before operation,
especially the muffler, air intakes and air
filters.
4. When replacing the any other part, or any
lubricant, always be sure to use only
RedMax products or products which have
been certified by RedMax for use with the
RedMax product.
U
S
5. In the event that any part must be replaced
or any maintenance or repair work not
described in this manual must be
■ For protecting your body from vibration
performed, please contact a representative
from the store nearest RedMax authorized
servicing dealer for assistance.
6. Do not use any accessory or attachment
other than those bearing the RedMax mark
and recommended for the unit.
7. Under no circumstances should you ever
take apart the product or alter it in any
way. Doing so might result in the product
becoming damaged during operation or the
product becoming unable to operate
properly.
WARNING
Prolonged use of a blower, exposing the
operater to vibrations and cold may
produce whitefinger disease (Raynaud's
phenomenon), which symptoms are
tingling and burning sensations followed
by loss of color and numbness in the
fingers.
All factors which contribute to whitefinger
disease are not known, but cold weather,
smoking diseases or physical conditions
as well as long periods of exposure to
vibration are mentioned as factors.
In order to reduce the risk of whitefinger
disease, the following precautions are
strongly recommended.
■ Disposal
When disposing your machine, fuel or oil for
the machine, be sure to allow your local
regulations.
a: Keep your body warm. Never use
blower during rains.
b: Wear thick anti-vibration gloves.
c: Take more than 5 minutes of break in
warm place frequently.
d: Maintain a firm grip at all times, but do
not squeeze the handles with constant,
excessive pressures.
e: If you feel discomfort, redness and
swelling of your fingers or any other part
of your body, see a doctor before getting
worse.
■ Maintenance
1. In order to maintain your product in proper
working order, perform the maintenance
and checking operations described in the
manual at regular intervals.
2. Always be sure to turn off the engine and
disconnect the spark plug before
performing any maintenance or checking
procedures.
WARNING
The metallic parts and engine cover reach
high temperatures immediately after
stopping the engine.
3. Examine the blower at intervals for loose
US-7
Download from Www.Somanuals.com. All Manuals Search And Download.
EBZ3050RH
6. Set up
■ BLOWER TUBES
F1
1. Connect the blower and swivel joint
with flexible hose. Clamp both ends of
the flexible hose securely with the
hardware supplied with the unit.
2. Align the protrusion and the groove
provided on the tube ends and twist the
tube until connection is locked up.
NOTE
A light lubricant may be used to ease
assembly of flexible pipe to blower
elbow.
F2
■ THROTTLE LEVER
• Set up the clamp to the swivel and
tighten the screw on the clamp.
(1) Clamp
(2) Swivel
(3) Screw
F3
■ THROTTLE CABLE
1. First, lightly tighten the hose in the
middle of it by putting the band through
the hole (a).
2. Next, lightly tighten the cable by putting
the band through the hole (b).
(1) Hose
(2) Band
(3) Cable
US-8
Download from Www.Somanuals.com. All Manuals Search And Download.
EBZ3050RH
7. Fuel
FUEL
lines or fuel tank of the engine.
WARNING
NOTE
• Gasoline is very flammable. Avoid smoking or bringing any
flame or sparks near fuel. Make sure to stop the engine and
allow it cool before refueling the unit. Select outdoor bare
ground for fueling and move at least 10 ft (3 m) away from
the fueling point before starting the engine.
• Failures caused by operating engines on gasoline with octane
rating lower than 89 are not covered by the RedMax Two-
Stroke engine warranty.
U
S
WARNING
• Alternative Fuels (Not Gasoline)
Alternative fuels, such as E-15 (15% ethanol), E-20 (20%
ethanol), E-85 (85% ethanol) are NOT classified as gasoline
and are NOT approved for use in RedMax 2-stroke gasoline
engines. Use of alternative fuels will cause major engine
performance and durability problems such as: improper
clutch engagements, overheating, vapor lock, power loss,
lubrication deficiency, deterioration of fuel lines, gaskets
and internal carburetor components, etc... Alternative fuels
cause high moisture absorption into the fuel/oil mixture
leading to oil and fuel separation.
■ GASOLINE REQUIREMENTS
• All 2-Stroke RedMax Products are powered by RedMax
Professional-Commercial Duty, Hi-Performance, Hi-RPM, Air
Cooled 2-Stroke engines.
RedMax – Hi-Performance 2-stroke engines produce higher HP
outputs as compared to standard Home Owner Duty or Light
Commercial Duty production engines offered by most
manufacturers.
• Exhaust emission are controlled by the fundamental engine
parameters and components (eq., carburation, ignition timing
and port timing) without addition of any major hardware or the
introduction of an inert material during combustion.
• The RedMax Engines are registered and certified with CARB
(California Air Resources Board) and EPA (Environmental
Protection Agency) to operate on CLEAN Mid-grade 89 octane
or Premium, unleaded (lead-free) gasoline and RedMax Air-
Cooled "Max Life", Synthetic blend Premium two-stroke engine
oil mixed at 50:1 ratio.
■ OIL REQUIREMENTS
• Use only RedMax "Max Life", Synthetic blend Premium Air-
Cooled two-stroke engine oil or oil certified to ISO-L-EGD
(ISO/CD1378) standard AND one that is JASO-FD registered.
RedMax Air-Cooled "Max Life", Synthetic blend Premium two
stroke engine oil and ISO-L-EGD (ISO/CD1378) AND JASO-FD
oils are fully compatible with gasoline's containing 10% Ethanol.
RedMax Air-Cooled "Max Life", Synthetic blend Premium two
stroke engine oil and ISO-L-EGD (ISO/CD1378) AND JASO-FD
oils are Universal and should be mixed at 50:1 ratio for all 2
stroke air cooled engines sold in the past regardless of mixing
ratios specified in those manuals.
• Unleaded gasoline is recommended to reduce the
contamination of the air for the sake of your health and the
environment.
• If the oil is registered with JASO, the JASO Logo with FD and
registration number will be displayed on the container. The
highest JASO rating is "FD", which equals the ISO-L-EGD
rating. Lower ratings are "FC", "FB", and "FA".
• This Hi-Performance Air Cooled 2-stroke Engine requires the
[ R+M ]
use of Minimum 89 Octane
(Mid grade or Premium)
2
clean gasoline. Gasoline may contain maximum of 10% Ethanol
(grain alcohol) or up to 15% MTBE (Methyl tertiary-butyl ether).
Gasoline containing Methanol (Wood Alcohol) is NOT
approved.
NOTE
• Engine problems due to inadequate lubrication caused by
failure to use ISO-L-EGD certified and JASO FD registered oil
such as "MaxLife", RedMax Synthetic blend Premium 2-stroke
oil WILL VOID THE REDMAX TWO-STROKE ENGINE
WARRANTY.
• IF octane rating of the Mid Grade gasoline in your area is lower
than 89 Octane use Premium Unleaded Gasoline. The majority
of all 2-stroke engine manufacturers in the USA and Canada
recommend using gasoline with 89 Octane or higher.
WARNING
WARNING
• Gasoline with an octane rating lower than 89 will greatly
increase the engines operating temperature. Low octane
gasoline will cause detonation (knock) resulting in piston
seizures and major internal engine components damage.
• Poor quality gasolines or oils may damage sealing rings, fuel
• Do not use NMMA (National Marine Manufacturers
Association), BIA (Boating Industry Association), and TCW (two
cycle water cooled) oils designed for MoPeds or Outboard,
water cooled Marine Engines. Do not use API (American
Petroleum Institute), TC (Two Cycle) labeled oils. The API-TC
US-9
Download from Www.Somanuals.com. All Manuals Search And Download.
EBZ3050RH
7. Fuel
test standard has been discontinued by API in 1995 and it no
longer exists.
WARNING
1. Select flat and bare ground for fueling.
2. Move at least 10 feet (3 meters) away from the fueling point
before starting the engine.
3. Stop the engine before refueling the unit. At that time, be
sure to sufficiently agitate the mixed gasoline in the
container.
IMPORTANT
• Gasoline/Oil mixture Storage Recommendations
Store your gasoline or gasoline/oil mixture in a cool dry area in
a tightly sealed approved container to limit the entry of moisture
and additional air (oxygen). Moisture and air cause the
development of varnish and gum, making the fuel stale. Stored
gasoline and gasoline/oil mixture ages and loses its octane
rating and volatility. Do not mix more gasoline/oil than you
intend to use in 30 days, and 60 days when fuel stabilizer is
added. RedMax Air-Cooled "Max Life" Synthetic blend
Premium two-stroke engine oil "Contains fuel stabilizer" and
will automatically extend your gasoline/oil mixture life up to 60
days.
■ FOR YOUR ENGINE LIFE, AVOID
1. FUEL WITH NO OIL (RAW GASOLINE) – It will cause severe
damage to the internal engine parts very quickly.
2. GASOHOL – It can cause deterioration of rubber and/or plastic
parts and disruption of engine lubrication.
3. OIL FOR 4-CYCLE ENGINE USE – It can cause spark plug
fouling, exhaust port blocking, or piston ring seizure.
4. Mixed fuels which have been left unused for a period of
one month or more may clog the carburetor and result in the
engine failing to operate properly.
5. In the case of storing the product for a long period of time,
clean the fuel tank after rendering it empty. Next, Start the
engine and run the carburetor dry residual fuel.
6. In the case of scrapping the used mixed oil container, scrap it
only at an authorized depository site.
■ HOW TO MIX FUEL
RECOMMENDED MIXING RATIO
GASOLINE 50 : OIL 1
(when using RedMax Air-Cooled "Max
Life")
50:1 MIXING CHART
NOTE
GASOLINE
gal.
1
2
3
4
5
• As for details of quality assurance, read the description in the
section Limited Warranty carefully. Moreover, normal wear and
change in product with no functional influence are not covered
by the warranty. Also, be careful that, if the usage in the
instruction manual is not observed as to the mixed gasoline,
type of oil or fuel to be used. described therein, it may not be
covered by the warranty.
2-CYCLE OIL fl.oz
2.6
5.2
7.8 10.4 13
GASOLINE
liter
ml
1
2
3
4
5
2-CYCLE OIL
20
40
60
80
100
WARNING
• Pay attention to agitation.
1. Measure out the quantities of gasoline and oil to be mixed.
2. Put some of the gasoline into a clean, approved fuel container.
3. Pour in all of the oil and agitate well for 10seconds.
4. Pour in the rest of gasoline and agitate again for at least one
minute. As some oils may be difficult to agitate depending on oil
ingredients, sufficient agitation is necessary. Be careful that, if
the agitation is insufficient, there is an increased danger of early
piston seizure due to abnormally lean mixture.
5. Place a clear indication on the outside of the container to avoid
mixing up with gasoline or other containers that dont contain oil.
6. Indicate the contents on outside of container for easy
identification.
■ FUELING THE UNIT
1. Untwist and remove the fuel cap. Rest the cap on a clean
surface.
2. Put fuel into the fuel tank to 80% of the full capacity.
3. Fasten the fuel cap securely and wipe up any fuel spillage
around the unit.
US-10
Download from Www.Somanuals.com. All Manuals Search And Download.
EBZ3050RH
8. Operation
■ STARTING ENGINE
engine cover reach high
temperatures during operation and
doing so could result in serious
burns.
IMPORTANT
• Avoid operating the blower with the
flexible tube and swivel joint
disconnected. That will reduce the
cooling air and the engine could be
damaged by overheating.
U
S
6. Once the engine is running, gradually
open the choke if it was set closed, and
let the engine run at idle speed for a
minute to warm it up.
F6
1. Push the primer bulb until fuel flows out
in the clear tube. (F6)
NOTE
When the engine fails to start after
several attempts due to overchoking,
open the choke and repeat pulling the
rope.
(1) Primer Bulb
■ ADJUSTING IDLE SPEED (F10)
• The idling speed is set for 3000 rpm at
the factory. If it is necessary to adjust
the idle speed, use the adjustment
screw on the top side of carburetor.
F10
2. When the engine is cool, close the
choke. (F7)
F7
(1)
(1) Choke Lever
(2) CLOSE
(1) Idling Adjustment Screw
(3) OPEN
■ STOPPING ENGINE
F11
3. Set the ignition switch to the start
position. (F8)
4. Set the throttle lever in idling position.
(F8)
• Move the throttle lever to the idling
position and set the ignition switch to
the stop position. (F11)
F8
(3)
(1)
(1)
(1) Ignition Switch
(2)
(1) Full Throttle
(2) Idling
(3) Ignition Switch
5. To start, hold the top of the blower
firmly and hold the flame by your foot.
Pull the starter knob slowly until you
feel it engage and then give it a
vigorous strong pull. (F9)
F9
NOTE
If the engine won’t stop when setting
the ignition switch to the stop position,
close the choke lever and stop the
engine.
F12
In this case, please repair the machine
at your nealest servicing dealer. (F12)
IMPORTANT
• Avoid pulling the starter rope out to
its full extent and allowing the
starter rope to snap back. This will
prevent premature damage to the
starter.
(1) Choke Lever
(2) CLOSE
(3) OPEN
• Do not let a person stand near the
blower or the exhaust port.
• Never to touch the muffler, spark
plug, other metallic parts of the
engine or engine cover while the
engine is in operation or
immediately after shutting down the
engine. These metallic parts and
US-11
Download from Www.Somanuals.com. All Manuals Search And Download.
EBZ3050RH
9. Maintenance
Maintenance, replacement, or repair of the emission control device and
systems may be performed by any non-road engine repair establishment or
individual.
Daily
or
Before use
Every
25 hours
after
Every
50 hours
after
Every
100 hours
after
System/Compornent
Procedure
✔
✔
✔
Air Filter
Inspect/Clean
Inspect/Replace
Inspect/Replace
Inspect/Clean
Inspect/Clean
Inspect/Clean
Inspect/Clean
Inspect/Clean
Tighten
✔
✔
✔
Fuel Leaks
Fuel Filter
Fuel Line
Spark Plug
✔
Muffler
✔
Muffler Spark Arrester
Cooling System
Screws/Nuts/Bolts
Cylinder Exhaust Port
✔
✔
✔
Inspect/Clean
with dirt. The filter can be taken out of
the fueling port using a small wire hook.
Disconnect the filter assembly from the
fuel pipe and unhook the retainer to
disassemble it. Clean the components
with gasoline.
F15
WARNING
Make sure that the engine has stopped
and is cool before performing any
service to the blower. Contact with
rotating blower fan or hot muffler may
result in a personal injury.
(1) Screen
(2) Element
(3) Holder
(4) Retainer
■ AIR CLEANER
F13
• Check the air cleaner every 25 hours of
use or more frequently if used under
dusty conditions. A clogged air filter
may increase fuel consumption while
cutting down the engine power. Never
operate the blower without the air filter
or with a deformed filter element
because unfiltered dusty air may
quickly ruin the engine.
■ SPARK PLUG
• The spark plug may gather carbon
deposits on its firing end with
reasonable use. Remove and inspect
the spark plug every 25 hours and clean
the electrodes as necessary with a wire
brush. The spark gap should be
adjusted to .025 in (0.6~0.7mm).
• Plug manufacturers recommend
replacing the plug twice a year to avoid
unexpected plug failure in a job.
F16
CLEANING AIR FILTER:
1. Remove the air cleaner cover.
2. Use neutral detergent and warm water
to clean the filter element. After
cleaning, air dry the element
completely.
REPLACEMENT PLUG IS A NGK
CMR7H.
F14
3. Reinstall the filter.
Never forget to attach the screen. If the
screen is not attached, the cleaner will
not seal properly and the dusts come
into the cylinder.
IMPORTANT
• Note that using any spark plugs other
than those designated may result in the
engine failing to operate properly or in
the engine becoming overheated and
damaged.
(1) Element
(2) Screen
• To install the spark plug, first turn the
plug until it is finger tight, then tighten it
a quarter turn more with a socket
wrench.
■ FUEL FILTER
• A clogged fuel filter may cause poor
acceleration of the engine. Check
periodically to see if the filter is clogged
US-12
Download from Www.Somanuals.com. All Manuals Search And Download.
EBZ3050RH
9. Maintenance
■ MUFFLER
net. When air flow has dropped down
during operation, stop the engine and
inspect the air inlet net for blocking by
obstacles.
F19
WARNING
• Inspect periodically, the muffler for
loose fasteners, any damage or
corrosion. If any sign of exhaust
• Note that failure to remove any such
obstacles may result in the engine
becoming overheated and damaged.
U
S
leakage is found, do not use the blower
and have it repaired immediately.
• Note that failing to do so may result
in the engine catching on fire.
(1) Net
WARNING
Never use the blower without the net of
the blower. Before each use, check
that the net is attached in place and is
free from any damage.
IMPORTANT
• Before starting operation, always make
sure to check if the muffler is properly
held by two bolts (F17 (2)). (Fastening
Torque : 7 to 11 N·m)
• Also make sure that the spark arrester
and the diffuser are properly attached
with two bolts (F17 (1)). (Fastening
Torque : 2 to 3 N·m)
F17
■ IGNITION COIL AIR GAP
INSPECTION
• If the gap is out of standard or when
installing the coil or rotor, adjust the air
gap between the ignition coil and the
iron core of the rotor.
F20
• Even if one of four bolts is loose, it may
result in engine catching on fire.
Air Gap:
(1) Bolt
(2) Bolt
0.3 ~ 0.4mm
0.012 ~ 0.016"
(3) Spark arrester
(4) Diffuser
(1) Rotor
(2) Ignition coil
■ SPARK ARRESTER
• The muffler is equipped with a spark
arrester to prevent red hot carbon from
flying out of the exhaust outlet.
Periodically inspect and clean as
necessary with a wire brush. In the
State of California it is required by law
(Section 4442 of the California Pulic
Resources Code) to equip a spark
arrester when a gas powered tool is
used in any forest covered, bush
covered, or grass covered unimproved
land.
■ SHOLDER STRAP
F21
• If the shoulder strap is damaged it may
break during use, thus causing the
product to fall and resulting in personal
injury. Follow the instructions below to
replace the shoulder strap with new
one.
1. Hook the upper part of the shoulder
strap at the notch on the top of the
frame and pass it through the buckle as
shown in the figure, then secure it
firmly.
2. Put the hook at the lower part of the
shoulder strap in the strap installing
location at the bottom of the frame.
(1)
■ PROCEDURES TO BE PERFORMED
AFTER EVERY 100 HOURS OF USE
1. Remove the muffler, insert a
screwdriver into the vent, and wipe
away any carbon buildup. Wipe away
any carbon buildup on the muffler
exhaust vent and cylinder exhaust port
at the same time.
(2)
F18
(1) Buckle
(2) Frame
(3) Hook
2. Tighten all screws, bolts, and fittings.
(4) D-ring
■ AIR INLET NET
(3)
(4)
IMPORTANT
• Blowing air is taken in from the air inlet
US-13
Download from Www.Somanuals.com. All Manuals Search And Download.
EBZ3050RH
10. Storage
BEFORE STORING THE BLOWER:
1. Drain a fuel tank and push the primer
bulb until it becomes empty of fuel.
2 .Remove the spark plug and drop a
spoonful of 2-cycle oil into the cylider.
Crank the engine several time and
install the spark plug.
3. Store unit in a dry, dust free place, out
of the reach of children.
11. Disposal
• When disposing your machine, fuel or
oil for the machine, be sure to allow
your local regulations.
12. Troubleshooting guide
Case 1. Starting failure
CHECK
PROBABLE CAUSES
incorrect fuel
ACTION
drain it and with correct fuel
clean
fuel tank
fuel filter
➞
➞
➞
➞
➞
➞
➞
➞
➞
➞
➞
➞
fuel filter is clogged
out of normal range
spark plug is fouled/wet
plug gap is incorrect
disconnected
carburetor adjustment screw
sparking (no spark)
adjust to normal range
clean/dry
correct (GAP: 0.6 – 0.7 mm)
retighten
spark plug
Case 2. Engine starts but does not keep running/Hard re-starting.
CHECK
PROBABLE CAUSES
incorrect fuel or staled fuel
out of normal range
carbon is built-up
ACTION
drain it and with correct fuel
adjust to normal range
wipe away
fuel tank
➞
➞
➞
➞
➞
➞
➞
➞
➞
➞
carburetor adjustment screw
muffler,cylinder (exhaust port)
air cleaner
clogged with dust
wash
cylinder fin, fan cover
clogged with dust
clean
When your unit seems to need further service, please consult with our service shop in your area.
US-14
Download from Www.Somanuals.com. All Manuals Search And Download.
EBZ3050RH
FEDERAL AND CALIFORNIA EMISSIONS CONTROL WARRANTY
STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS
U
S
The EPA (U.S. Environmental Protection Agency), CARB (California Air Resources Board), Environment
Canada and RedMax are pleased to explain the emissions control system's warranty on your 2009 and later
small off-road engine. In U.S. and Canada, new equipment that use small off-road engines must be designed,
built, and equipped to meet the applicable Federal or Californian stringent anti-smog standards. RedMax must
warrant the emissions control system on your small off-road engine for the period listed below provided there
has been no abuse, neglect or improper maintenance of your equipment. Your emissions control system may
include parts such as carburetor, ignition system, catalytic converter, fuel tank, filters and other associated
components. Also, included may be hoses, belts, connectors, sensors, and other emission-related assemblies.
Where a warrantable condition exists, RedMax will repair your small off-road engine at no cost to you including
diagnosis, parts and labor.
MANUFACTURER'S WARRANTY COVERAGE
This emissions control system is warranted for two years or if the product qualifies for a longer warranty period
resulting from the type of use, that period shall prevail. If any emissions-related part on your equipment is
defective, the part will be repaired or replaced by RedMax.
OWNER'S WARRANTY RESPONSIBILITIES
As the small off-road engine owner, you are responsible for performance of the required maintenance listed in
your Owner's Manual. RedMax recommends that you retain all receipts covering maintenance on your small off-
road engine, but RedMax cannot deny warranty solely for the lack of receipts or your failure to ensure the
performance of all scheduled maintenance. As the small off-road engine owner, you should however be aware
that the RedMax may deny you warranty coverage if your small off-road engine or a part has failed due to
abuse, neglect, or improper maintenance or unapproved modifications.
You are responsible for presenting your small off-road engine to a RedMax distribution center or service center
as soon as the problem exists. The warranty repairs should be completed in a reasonable amount of time, not to
exceed 30 days. If you have any questions regarding your warranty coverage, you should contact RedMax at 1-
800-291-8251 or via e-mail at [email protected].
WARRANTY COMMENCEMENT DATE
The warranty period begins on the date the engine or equipment is delivered to an ultimate purchaser.
LENGTH OF COVERAGE
RedMax warrants to the ultimate purchaser and each subsequent owner that the engine or equipment is
designed, built, and equipped so as to conform with all applicable regulations adopted by EPA and CARB, and
is free from defects in materials and workmanship that causes the failure of a warranted part for a period of two
years.
WHAT IS COVERED
REPAIR OR REPLACEMENT OF PARTS Repair or replacement of any warranted part under the warranty
must be performed at no charge to the owner at a warranty station. Warranty services or repairs will be provided
at all RedMax distribution centers that are franchised to service the subject engines. Throughout the emissions
warranty period of two years, RedMax must maintain a supply of warranted parts sufficient to meet the expected
demand for such parts.
WARRANTY PERIOD Any warranted part that is scheduled for replacement as required in the maintenance
schedule, is warranted for the period of time prior to the first scheduled replacement point for that part. If the
part fails prior to the first scheduled replacement, the part will be repaired or replaced by RedMax at no cost.
Any such part repaired or replaced under warranty is warranted for the remainder of the period prior to the first
scheduled replacement point for the part. Any warranted part that is not scheduled for replacement as required
in the maintenance schedule, is warranted for two years or if the product qualifies for a longer warranty period
resulting from the type of use, that period shall prevail. If any such part fails during the period of warranty
coverage, it will be repaired and replaced by RedMax at no cost. Any such part repaired or replaced under the
US-15
Download from Www.Somanuals.com. All Manuals Search And Download.
EBZ3050RH
warranty is warranted for the remaining warranty period. Any warranted part that is scheduled only for regular
inspection in the maintenance schedule will be warranted for a period of two years. A statement in such written
instructions to the effect of "repair or replace as necessary" will not reduce the period of warranty coverage. Any
such part repaired or replaced under warranty will be warranted for the remaining warranty period.
DIAGNOSIS The owner must not be charged for diagnostic labor that leads to the determination that a
warranted part is in fact defective, provided that such diagnostic work is performed at a warranty station.
CONSEQUENTIAL DAMAGES RedMax is liable for damages to other engine components proximately caused
by a failure under warranty of any warranted part.
EMISSION WARRANTY PARTS LIST
1. Air-induction system*
2. Fuel system*
3. Ignition system*
4. Fuel tank, cap and lines as applicable*
*some components only covered up to point specified by maintenance schedule
WHAT IS NOT COVERED
All failures caused by abuse, neglect or improper maintenance are not covered.
ADD-ON OR MODIFIED PARTS
Add-on or modified parts that are not exempted by CARB or EPA may not be used. The use of any non-
exempted add-on or modified parts will be grounds for disallowing a warranty claim. RedMax will not be liable to
warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.
HOW TO FILE A CLAIM
If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest
authorized servicing dealer or contact RedMax at 1-800-291-8251 or via e-mail at [email protected].
WHERE TO GET WARRANTY SERVICE
Warranty services or repairs are provided through all RedMax authorized servicing dealers.
MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS
Any replacement part may be used in the performance of any warranty maintenance or repairs and must be
provided without charge to the owner. Such use will not reduce the warranty obligations of the manufacturer.
MAINTENANCE STATEMENT
The owner is responsible for the performance of all required maintenance, as defined in the operator's manual.
US-16
Download from Www.Somanuals.com. All Manuals Search And Download.
|