Part 5-Addjustingg display and using cord management
Route cords along articulating arms using cord management clips(7).
Articulating arms can be adjusted to position display into desired location.
Use wrench to tighten and loosen the tension screw. Do not overtighten
and do not loosen to the point the screws come out.
INSTALLATION GUIDE
Item No.::PSW771
8
9
7
Thank you for choosing our product
Pyle Audio
TV size range: 32"～50"
1600 63rd st , Brooklyn, NY, 11204
Maximum weight capacity: 40 kg /88lbs
Adjustable angle: 0°～12°
(718)236-8000
Warning
This product contains small items that could be a choking hazard if swallowed. Keep
these items away from young children!
www.pyleaudio.com
1.Make sure these instructions are read and completely understood before attempting
installation. If you are unsure of any part of this installation, contact a professional
installer for assistance.
MADE IN CHINA
CAUTION
2.The wall or mounting surface must be capable of supporting the combined weight of
the mount and the display; otherwise the structure must be reinforced.
3.Safety gear and proper tools must be used. A minimum of two people are required
for this installation. Failure to use safety gear can result in property damage, serious
injury or death.
This product was designed to be installed on wood stud walls and solid concrete walls.
Before installing make sure the supporting surface will support the combined load of the
equipment and hardware. Never exceed the Maximum Load Capacity. This product is
intended for indoor use only. Use of this product outdoors could lead to product failure or
personal injury.
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 1aa-Wood SStud Moouunting
Part 2bb-Attaacching brracketts to scrreen wiith reccessed back
Use wall plate(1) as a template, make sure it is level, and mark four mounting
holes along the center lines of the wood studs. Drill four 3/16”(5mm)dia.
holes 2”(50mm) deep. Level wall plate(1) and attach to wall with four long
bolts(J) and four washers(L). Tighten screws firmly. Do not overtighten.
Center brackets vertically on back of screen. Select the medium(F or G) or
large(H) screws. Attach brackets to screen using four selected screws,four
square washers(I) and four spacers(M) at the top and bottom of each bracket.
Tighten screws firmly. Do not overtighten.
Square washer(I)
M
I
Large hole for
M8 screws
F-H
Medium hole for
M5 and M6 screws
Stud finder
2”(50mm)
Wood stud
3/16”(5mm)
L
J
-3-
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
Part 2aa-Attaacching Brracketts To Scrreen Wiith Flaat Back
Part 1b--Concrette Wall MMoounting
Center brackets vertically on back of screen. Select the small(A or B),
medium(C or D) or large(E) screws. Attach brackets to screen using four
selected screws and four square washers(I) at the top and bottom of each
bracket. Tighten screws firmly. Do not overtighten.
Level wall plate and use wall as a template to mark four holes. Drill four
3/8” (10mm) dia. holes 2”(50mm) deep. Insert four anchors(K) into holes
and secure wall plate with four long bolts(J) and four washers(L). Tighten
bolts firmly. Do not overtighten.
Square washer(I)
I
Large hole for
M8 screws
2”(50mm)
A-E
Medium hole for
M5 and M6 screws
Φ3/8”(10mm)
Small hole for
M4 screws
Concrete Wall
K
L
J
-5-
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
|