PJ X3241N
PJ WX3231N
DATA PROJECTOR
OWNER’S MANUAL
For safe and correct use, be sure to read “Before Using” before using the machine.
In the spaces provided below, record the Model and Serial No. located at the bottom of
your projector.
Model No.
Serial No.
Retain this information for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the sales representative or an experienced radio/TV technician for help.
RESPONSIBLE PARTY: Ricoh Americas Corporation
5 Dedrick Place, West Caldwell, NJ 07006
Phone: 973-88ꢀ-ꢀ000
CAUTION: Changes or modifications made to this equipment, not expressly approved by
Ricoh, or parties authorized by Ricoh, could void the user’s authority to operate
the equipment.
USA only
Notice:
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil
numérique de la classe B est conforme à la norme NMB-003 du Canada.
CANADA only
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND
INSTRUCTIONS GIVEN IN THIS OWNER’S MANUAL AND THOSE
MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE
REFERENCE.
This unit is fully transistorized and does not contain any parts that can be repaired by the
user.
WARNING: DO NOT REMOVE THE CABINET COVER, ORYOU MAY BE
EXPOSED TO DANGEROUS VOLTAGE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL ONLY.
1. Read Owner’s Manual
3. Source of Light
After unpacking this product, read
the owner’s manual carefully, and
follow all the operating and other
instructions.
Do not look into the lens while the
lamp is on. The strong light from
the lamp may cause damage to
your eyesight.
2. Power Sources
4. Ventilation
This product should be operated
only from the type of power source
which does not exceed the voltage
range specified on the rating label
and the power cord.
If you are not sure of the type
of power supply to your home,
consult your sales representative
or local power company.
Openings in the cabinet are
provided for ventilation and to
ensure reliable operation of the
product and to protect it from
overheating. These openings must
not be blocked or covered. Never
block an opening by placing the
product on a bed, sofa, rug or
other similar surface. Do not place
it in a built-in installation such as
a bookcase or rack, unless proper
ventilation is provided.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Heat
8. Be sure that you firmly
insert the plug into the wall
outlet.
The product should be situated
away from heat sources such as
radiators, heat registers, stoves,
or other products (including
Incorrect or faulty connections
may result in fire or electric shock.
Avoid using an unsound or loose
outlet.
amplifiers) that produce heat.
6. Water and Moisture
Do not use this product near water.
- for example, near a bath tub,
wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a
swimming pool and other similar
environments.
9. Power Cord Protection
Power cords should be routed
so that they are not likely to be
walked on or pinched by items
placed upon or against them,
paying particular attention to cords
at plugs, convenience receptacles,
and the point where they exit from
the product.
7. Cleaning
Unplug this product from the wall
outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners.
Always use a soft cloth for
cleaning.
10. Overloading
Do not overload wall outlets. To
reduce the risk of electric shock,
do not use the polarized plug with
an extension cord , receptacle, or
other outlet unless the blades can
be inserted completely with three-
wire grounding type to prevent
blade exposure. Failure to follow
these instructions may result in fire
or electric shock.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (Continued)
11. Lightning storms
14. Do not place the product
vertically
For added protection for this
product during a storm, or when it
is left unattended and unused for
long periods of time, unplug it from
the wall outlet. This will prevent
damage to the product due to
lightning and power-line surges.
Never operate this unit on AC
power during a thunderstorm. If
you see lightning or hear thunder,
never touch the unit, cables and/or
peripherals. An electric surge
caused by the storm, may result in
an electrical shock or damage to
the unit.
Do not use the product in the
upright position or any other
vertical positions to project the
pictures. It may fall which could
result in serious injury and/or
damage to the product.
15. Stack Inhibited
Do not stack other equipment on
this product and do not place this
product on other equipment. The
top and bottom surface of this
product increase in temperature
during normal use and may
damage the other unit.
12. Object and Liquid Entry
Never push objects of any kind into
this product through openings as
they may touch dangerous voltage
points or short-out parts that could
result in a fire or electric shock.
Never spill liquid of any kind on the
product.
16. Attachments
Do not use attachments not
recommended by the product
manufacturer.
Use of an incompatible
attachments could cause hazards
or damage to the product.
13. Do not place or keep the
projector within the reach
of the children.
It may fall or tip over, possibly
causing serious injury.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
17. Accessories
19. If glass components,
including lens and lamp,
should break, contact your
sales representative for
repair service.
Do not place this product on an
unstable cart, stand, tripod, bracket,
or table. The product may fall, causing
serious injury to a child or adult, and
serious damage to the product. A
product and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the product and cart
combination to overturn.
This product incorporates glass
components, including a lens and
a lamp.
If these should break, please
handle with care to avoid injury and
contact your sales representative
for repair service. Avoid any broken
pieces of glass since they may
cause injury. In the unlikely event
that the lamp ruptures, thoroughly
clean the area around the projector
and discard any edible items
placed in that area since they may
be contaminated.
S31ꢀ5A
18. Damage Requiring Service
Unplug this product from the wall
outlet and take the product to qualified
service personnel if you encounter
any of the following conditions:
a) The power supply cord or plug is
damaged.
b) Liquid has been spilled, or objects
have fallen into the product.
c) The product has been exposed to
rain or water.
20. Servicing
Do not attempt to service this
product yourself as opening or
removing covers may expose you
to dangerous voltage or other
hazards. Refer all servicing to
qualified service personnel.
d) The product does not operate
normally when following the
21. Do not place anything in
front of the lens while the
projector is operating
operating instructions. Adjust only
those controls that are covered by
the operating instructions since
an improper adjustment of other
controls may result in damage and
will often require extensive work by
a qualified technician to restore the
product to its normal operation.
e) The product has been dropped or
damaged in any way. (If the cabinet
should break, please handle with
care to avoid injury.)
Things placed in front of the lens
may overheat and burn or start a
fire.
If you want to temporarily stop the
projected image, use the mute on
the remote control.
f) The product exhibits a distinct
change in performance, which
indicates a need for service.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS (Continued)
22. Replacement Parts
25. Do not use the product
in a closed installation
location.
When replacement parts are
required, be sure the service
technician has used replacement
parts specified by the manufacturer
or have the same characteristics
as the original part.
Unauthorized substitutions may
result in fire, electric shock, or
other hazards.
Do not place the product in a box
or in any other closed installation
location. Otherwise it may overheat,
which could result in a risk of fire.
26. When using a wireless
LAN function:
(Only the replacement of the lamp
should be made by users.)
• Do not use near people
with heart pacemakers.
• Do not use near electronic
medical equipment, or in
hospitals or other medical
institutions.
• Do not use inside aircraft
or in places where the
wireless LAN function
could interfere with
23. Safety Check
Upon completion of any service
or repairs to this product, ask
the service technician to perform
safety checks to verify that the
product is in proper operating
condition.
24. Do not leave thermal-
paper documents or easily
deformed items on top
of the unit or near the air
exhaust for long periods of
time.
electromagnetic signals.
The electromagnetic interference
could cause a malfunction,
resulting in an accident.
27. If the use of a wireless
LAN function interferes
with another device’s
The heat from the unit could erase
the information on the thermal
paper, or cause deformation or
warping.
electromagnetic signals,
cease use immediately.
The electromagnetic interference
could cause a malfunction,
resulting in an accident.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER SUPPLY INFORMATION
If your line voltage is ꢀꢀ0 to ꢀ40 V, use one of the following types of cable/plug.
Plug
Plug
configuration Plug type
Line voltage
ꢀꢀ0 – ꢀ40 V
configuration Plug type
Line voltage
ꢀ00 – ꢀ40 V
Australian
ꢀ40 V
10 A
EURO
UK
Switzerland ꢀ00 – ꢀ40 V
ꢀꢀ0 – ꢀ40 V
ꢀ40 V
6 A
Use a 5 A fuse which is approved by
ASTA or BSI to BSI36ꢀ.
Always replace the fuse cover after
changing the fuse.
North American ꢀ00 – ꢀ40 V
ꢀ40 V
15 A
IMPORTANT PRECAUTIONS
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on the
lens and the crucial internal parts. Do not use the unit for at least ꢀ hours when there is an
extreme or sudden change in temperature to prevent the unit from possible damage.
Place and Manner of Installation
• Do not place in hot locations, such as near heating equipment. Doing so could cause a
malfunction, and shorten the life of the projector.
• Avoid locations with oil or cigarette smoke. These environments will dirty the optical parts,
shortening their lives, and darkening the screen.
• Do not use this product in the upright position or tilt it up or down by more than ꢀ0° from
level. Doing so may cause a failure or shorten the life of the product.
• Using this instrument near a TV or radio may cause interference to the images or audio
sound. If this happens, move it away from the TV or radio.
• In a high altitude location where air is thin, cooling efficiency is reduced so use the
projector with [Fan mode] set to [High].
•
Only plug the power cord into outlets rated for use within the power cord’s specified voltage
range. Do not overload extension cords or power strips as this can result in fire or electric shock.
• Route the power cable or the connecting cable away from where people could trip over it.
The projector may fall, which could result in serious injury and/or damage to the product.
• Be sure the power cord is easily reached for unplugging in case of emergency. Do not
place any obstacles near a wall outlet in which the cord is plugged.
Avoid Volatile Liquid
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or
plastic products touching the unit for a long time as they will leave marks on the finish.
Do not use a chemically saturated cloth on the unit.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS (Continued)
LCD Panel
• If the air filter is stained or clogged, the main unit inner temperature rises. As a result, the
life of the LCD is shortened and a malfunction may also occur.
Clean the air filter from time to time and replace it regularly. It is recommended that you
replace the filter at the time you replace the lamp. (Ask your sales representative where
the unit was purchased or your nearby service station about an air filter for replacement.)
EXEMPTION CLAUSES
• Ricoh Corporation bears no responsibility in the case of damages arising from natural
disaster such as earthquakes, lightning, etc., fire not liable to Ricoh Corporation, acts by
third parties, other accidents, or use under abnormal conditions including erroneous or
improper operation and other problems.
• Ricoh Corporation bears no responsibility for incidental damages (lost profit, work
interruption, corruption or loss of the memory contents, etc.) arising from the use of or the
inability to use this unit.
• Ricoh Corporation accepts no liability whatsoever for any damages arising from not
having followed the descriptions in this Owner’s Manual.
• Ricoh Corporation accepts no liability whatsoever for any damages arising from
malfunctions arising from combination with equipment or software that is not related to
Ricoh Corporation.
• Ricoh bears no responsibility for information being intercepted or leaked due to the use of
a wireless LAN, or any damages therefore.
OTHER INFORMATION
Copyrights
Showing or transmitting commercial imaging software or broadcast or cable-broad casting
programs with the purpose of other than the personal and private viewing, including
modifying images using the freeze or resize functions, or displaying with the varying
aspect ratio of the images, could violate the direct or indirect copyrights of the imaging
software or broadcast program, etc., if done without first consulting with the copyright
holder. For this reason, please take appropriate measures including obtaining a license
from the copyright holder, before performing one of the actions listed above.
Disposal
This product contains substances which are harmful to humans and the environment.
• The lamp contains mercury.
Please dispose of this product or used lamps in accordance with local regulations.
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as
household waste. By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service or
the shop where you purchased the product.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OTHER INFORMATION (Continued)
Trademarks
• VGA, SVGA, XGA, SXGA, UXGA and WXGA are trademarks or registered trademarks of
International Business Machines Corporation.
• Mac is a registered trademark of Apple Computer, Inc.
•
Microsoft, Windows, Windows ꢀ000, Windows XP, Windows Vista, Windows 7 and PowerPoint
are registered trademarks or trademarks of Microsoft Corporation in the U.S. and other countries.
• Adobe and Acrobat Reader are registered trademarks of Adobe Systems Incorporated.
• Contains technology by Sasken, Inc.
Copyright © ꢀ000-ꢀ010 Sasken, Inc. All rights reserved.
• All other brand and product names are trademarks or registered trademarks of their
respective companies.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI licensing LLC.
Notational Conventions Used in This Manual
• References to pages with related information are annotated as follows.
For example, if making a reference to page 36:
• The illustrations in this document are for reference purposes only and may not reflect
your package exactly.
REMOTE CONTROL BATTERIES
Warning
• Never throw batteries into a fire.
Using the batteries improperly may cause them to explode or leak and may result in serious injury.
If battery-leaking fluid contacts skin, wash the fluid off immediately with clean water and consult
a doctor. If the fluid spills on an instrument, avoid contact and wipe it off using tissue paper.Then
dispose of the used tissue paper as flammable garbage after moistening the tissue with water.
Notes
• Be sure to use AAA (LR03) size batteries.
• Dispose of batteries in a designated disposal area.
• Attention should be drawn to the environmental aspects of battery disposal.
• Do not mix different battery types or combine used batteries with new ones.
• If the remote control does not operate correctly, or if the operating range becomes
reduced, replace both batteries with new ones.
• If the batteries are dead or if you will not be using the remote control for a long time,
remove the batteries to prevent battery acid from leaking into the battery compartment.
• Following information is only for EU-member states:
[Disposal of batteries and/or accumulators]
The crossed out wheeled dust bin symbol indicates that batteries and/or
accumulators must be collected and disposed of separately from household waste.
If the battery or accumulator contains more than the specified values of lead
(Pb), mercury (Hg), and/or cadmium (Cd) defined in the Battery Directive
(ꢀ006/66/EC), then the chemical symbols for lead (Pb), mercury (Hg) and/or
cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.
By participating in separate collection of batteries, you will help to assure
the proper disposal of products and batteries and thus help to prevent
potential negative consequences for the environment and human health.
For more detailed information about the collection and recycling
programmes available in your country, please contact your local city office
or the shop where you purchased the product.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
CONTENTS ................................................................................................1ꢀ
Placement ...................................................................................................ꢀ1
Connection..................................................................................................ꢀ4
Turning the power on and off.......................................................................ꢀ6
Basic operations..........................................................................................ꢀ8
Using handy features ..................................................................................31
Resizing image ........................................................................................3ꢀ
Changing screen size ..............................................................................33
Setting the password ...............................................................................34
Using the menus 1 ......................................................................................36
The default setting menu .........................................................................4ꢀ
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus ꢀ ......................................................................................50
Computer settings....................................................................................56
The control setting menu .........................................................................57
Setting slideshow options ........................................................................58
Checking the projector status......................................................................60
Status display...........................................................................................60
Using the Network Projector .......................................................................61
Installing the applications............................................................................6ꢀ
Using the Network Utility.............................................................................64
Multiscreen function.................................................................................70
Easy Connect utility .................................................................................75
Operating the projector............................................................................79
Lamp replacement ......................................................................................91
Air filter cleaning..........................................................................................94
Lens and main unit cleaning .......................................................................95
Trouble indications.......................................................................................96
Troubleshooting...........................................................................................97
Specifications..............................................................................................99
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparations
Checking the package contents
Please make sure that the following items are included in the box, along with the main unit.
If any item is missing, immediately contact the store where you purchased the product.
(1)
(4)
(7)
(2)
(5)
(3)
(6)
(8)
(1) Remote control
(ꢀ) LR03 (SIZE AAA) batteries for remote control (ꢀ)
(3) CD-ROM
(5) RGB cable (3 m) [Note 1]
(6) Power cord [Note 1, ꢀ]
(7) Carrying bag
(8) Mouse remote control receiver
(4) Owner’s Manual
Notes
1: To maintain original performance, always use the supplied cables.
ꢀ: The shape and number of supplied power cords vary depending on the product destination.
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to
ship your projector. For maximum protection when shipping your projector, repack the set
as it was originally packed at the factory.
The Supplied CD-ROM
The supplied CD-ROM contains an owner’s manual which includes information not available
for the printed Owner’s manual (Getting started) and Projector Management Utility Manual
in Portable Document Format (PDF) in addition to each application software. Please use
Acrobat Reader 5 or later version to view the manual.
Adobe® Acrobat® Reader® or Adobe® Reader®
The supplied CD-ROM does not contain Acrobat® Reader®. If you cannot read PDF
files, please install Acrobat Reader software in your computer by downloading it from
the Adobe Systems website.
Viewing the manual
Double-click the PDF file in the folder with the name of a language on the CD-ROM.
Acrobat® Reader® launches, and the Owner’s Manual cover and list of bookmarks appear.
p.
Click a bookmark title to view that section of the manual. Click
to view a reference page
with related information. See the Help menu for more information about Acrobat® Reader®.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of each part on the main unit
(3)
(2)
(1)
(4) (5)
(6) (7) (8) (9)
(
10)(11) (12) (13
)
(
14
)
(
15)
(16) (15)(14)
Back
Front
Name
: Function
p.16
(1) Control panel
:
:
:
:
Operates the projector.
Adjusts screen size.
Adjusts screen focus.
(ꢀ) Zooming lever
(3) Focusing lever
(4) Lamp cover
(5) Air exhaust
(6) Air intake
Remove to replace lamp.
: Expels air that has grown hot inside the projector.
: Draws in air from outside the projector for internal cool
down.
(7) Lens cap
(8) Lens
:
Replace the cap when not using the projector to protect
the lens.
: Projects expanded image.
p.19
(9) Infrared remote sensor
:
Senses commands from the remote control.
: Connects the supplied power cord here.
(10
(11
(1ꢀ
(13
(14
(15
(16
)
)
)
)
)
)
)
AC IN socket
Terminals on the rear panel
Speaker
Antitheft lock slot
Foot adjuster release button
Foot adjuster
p.18
:
Connects external devices.
: Outputs audio sound.
: Attach a safety cable or any other antitheft device.
:
:
Press to set up or stow the foot adjuster.
Adjusts the vertical projection angle.
Air filter
: Prevents dirt and dust from getting into the inside of the
projector.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of each part on the control panel and remote control
Control panel
Remote Control
Remote control transmitter
(7)
(6)
(5)
(3)
(4)
(5)
(6)
(12)
(11)
(18)
(20)
(21)
(21)
(9)
(8)
(10)
(2)
(19)
(7)
(8)
Battery
cover
(1)
(1)
(15)
(16)
(17)
(13)
(14)
(4)
(3)
(2)
Name
: Main Function
Control panel
(1) ENTER button
(ꢀ) INPUT button
(3) MENU button
: Accepts the selected mode.
:
:
Selects input.
Displays menus.
(4) RETURN/MUTE button : Goes back one screen. Also, cuts off the picture and
(5) ON/STANDBY button/
ON/STANDBY indicator
(6) TEMP indicator
:
:
:
:
:
Turns the power on/off (standby).
Displays whether power is on or off (standby).
Lights when internal temperature is too high.
(7) LAMP indicator
Displays lamp mode.
(8) Selection button
Menu selections and adjustments, volume control and
keystone adjustment, etc.
Remote control
(1) ENTER button
(ꢀ) MENU button
: Accepts the selected mode.
:
:
:
:
:
Displays menus.
Turns the power on/off (standby).
(3) ON/STANDBY button
(4) AUTO SET button
(5) INPUT button
Performs auto-adjustment of input signals from computer.
Selects input.
(6) NETWORK button
Switches to network input mode.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Name
: Main Function
(7) RETURN button
(8) Selection button
: Goes back one screen.
:
Menu selections and adjustments, volume control and
keystone adjustment, etc.
(9) Mouse control button
:
:
:
:
Controls a mouse pointer.
®
(10)
(11)
(1ꢀ)
(13)
PAGE+ button
MUTE button
FREEZE button
Ten-Key button
Proceeds PowerPoint slides.
Cuts off the picture and sound temporarily.
Pauses image.
: Use as a ten-key pad with wireless LAN, from which
numbers and characters can be entered.
(
(
(
(
(
(
(
14
15
16
17
18
)
)
)
)
)
)
)
Remote control code switch
NCE button
:
Sets the code of remote control to that of the projector.
:
:
:
:
:
Changes picture mode.
SCREEN SIZE button
GUIDE button
Changes screen size.
Displays operation guide for slideshow.
RESIZE button
Enlarges image. p.32
Goes back PowerPoint® slides.
19
ꢀ0
PAGE- button
R-CLICK button
: Functions as right-click of a mouse. There are two R-
CLICK buttons. Either is usable.
(
ꢀ1
)
L-CLICK button
: Functions as left-click of a mouse. There are two L-CLICK
buttons. Either is usable.
Note
• For the remainder of this manual, buttons are referred to as follows:
Selection buttons
; ENTER button
⇒
⇒
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Names of the terminals on the rear panel
(1) (2) (3) (4)
(5)
(6) (7)
(8) (9)(10)
(11) (12)
Name
(1) USB terminal
(ꢀ) HDMI terminal
: Main Function
:
Connects a commercial USB memory device.
™
: Inputs digital signals from HDMI (High-Definition
Multimedia Interface) compatible digital source.
: Inputs audio signals from a computer or video equipment.
(Multiple use for COMPUTER 1 IN/ꢀ IN, VIDEO and S-
VIDEO)
(3) AUDIO IN terminal
(4) S-VIDEO terminal
: Inputs S video signals from video equipment.
(5) COMPUTER 1 IN (Y/PB/PR 1) terminal
: Inputs analog RGB signal from a computer or a
component video signal (Y/PB/PR) from video equipment.
(6) COMPUTER ꢀ IN (Y/PB/PR ꢀ) terminal/MONITOR OUT terminal
:
Inputs analog RGB signal from a computer or a
component video signal (Y/PB/PR) from video equipment.
It can also be used as MONITOR OUT terminal by the
switch of (7).
(7) Switch
:
Switches between COMPUTER ꢀ IN and MONITOR OUT.
(8) LAN terminal
(9) AC IN socket
: Connects a network cable.
: Connects the supplied power cord here.
: Outputs audio signals.
: Inputs video signals from video equipment.
: When operating the projector via a computer, connect
this to the controlling computer’s RS-ꢀ3ꢀC port.
(
(
(
10
11
1ꢀ
)
)
)
AUDIO OUT terminal
VIDEO terminal
CONTROL terminal
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing and using the remote control
Loading dry-cell batteries
Operating the remote
into the remote control
control
Point toward the projector’s infrared
remote sensor, and press any button
on the remote control.
1
Remove the battery cover.
• Operating the projector from the front
ꢀ
Insert the dry-cell batteries.
Be sure to align the plus and minus
ends of the batteries properly.
Approx.15°
Appr
o
x
.5
m
Note:
When operating the remote control
from behind the projector, the infrared
signal is reflected on the projecting
surface.The operating range therefore
may decrease depending on the
shape and material of the projecting
surface.
Two batteries (LR03, SIZE AAA) are used.
3
Replace the battery cover.
Dry-cell batteries
• Before using the batteries, be sure to observe the Safety Precautions described in
previous pages.
• Remove batteries from remote control when not using for extended periods.
• If the remote control stops working, or if its range decreases, replace all the batteries
with new ones. (ꢀ batteries (LR03 SIZE AAA))
• Keep the batteries away from the reach of children.
Batteries are choking hazards and can be very dangerous if swallowed. If the batteries
are swallowed, seek medical assistance immediately.
The remote control
• The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.
• Do not drop or bang.
• Do not leave in hot or humid locations.
• Do not allow it to get wet or place it on top of wet objects.
• Do not take it apart.
• In rare cases, ambient conditions could impede the operation of the remote control. If
this happens, point the remote control at the main unit again, and repeat the operation.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating a computer using the remote control
A computer can be operated using the projector’s remote control. This function is available
on any computer with the Windows® ꢀ000, Windows® XP, Windows Vista®, or Windows® 7
operating system, that is equipped with a USB port which can support USB ꢀ.0 (The mouse
remote control receiver is also supported on Mac OS X for the Mac). However, please note that
Ricoh does not guarantee the operation of all computers.
Connecting a computer
Connect the mouse remote control receiver (supplied) to a computer.
1
The remote control may fail to operate
if the mouse remote control receiver
is exposed to bright sunlight or
fluorescent lighting.
To USB port
In such a case, change position or
direction of the mouse remote control
receiver and retry.
Mouse remote control receiver
Operating a computer
Operate remote control’s buttons towards the mouse remote control receiver.
2
Moving the mouse pointer
Press the mouse control button in the direction you wish the mouse pointer to move.
To left click
Press the L-CLICK button (There are two L-CLICK buttons. Either is usable).
To right click
Press the R-CLICK button (There are two R-CLICK buttons. Either is usable).
To drag and drop
Holding down the L-CLICK button, move the mouse control button until the mouse
pointer is over the desired location, then release the L-CLICK button.
Using the computer’s page up [ ] and down [ ] function
↑
↓
Press the PAGE+ and PAGE- buttons to switch PowerPoint® slides.
Remote Control Top Remote Control Underside
R-CLICK
L-CLICK
L-CLICK
Mouse control
PAGE –
PAGE +
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
Placement
Placement Styles
As shown in the figures below, this device can be placed in 4 different styles.
The factory setting is “floor-mounted front projection.” Set the [Projection mode] in the
, in accordance with your needs.
Floor-mounted front projection
Floor-mounted rear projection
Ceiling-mounted front projection
Ceiling-mounted rear projection
WARNING
• Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS
when placing the unit. Attempting to clean and replace the lamp in a high location
by yourself may cause you to fall, resulting in injury.
• If you wish to mount the projector on the ceiling, be sure to ask your sales
representative before doing so. Mounting the projector on a ceiling requires special
ceiling brackets (sold separately) and specialized knowledge. Improper mounting
could cause the projector to fall, possibly resulting in injury and damage, to the unit.
•
If the projector is ceiling-mounted, install the breaker for turning off the power in
case of anomaly. Let everyone involved with the use of the projector know that fact.
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
Placement (Continued)
Projection Distance and Size
Use the figures, tables, and formulas below to determine the projection size and projection
distance. (Projection sizes are approximate values for full-size picture with no keystone
adjustment.)
PJ X3241N
Projection size (inches) - 0.890
a (min length) =
32.863
Projection size (inches) - 0.748
a (max length) =
Screen
27.363
As seen from above
Projection distance a
Projection
Height (H)
min length
max length
size
(zooming max) (zooming min)
90°
30 inches 0.89 m (ꢀ.9ꢀ ft.)
40 inches 1.19 m (3.90 ft.)
50 inches 1.49 m (4.89 ft.)
60 inches 1.80 m (5.91 ft.)
70 inches ꢀ.10 m (6.89 ft.)
80 inches ꢀ.41 m (7.91 ft.)
1.07 m (3.51 ft.) 6.50 cm (0.ꢀ1 ft.)
1.44 m (4.7ꢀ ft.) 8.70 cm (0.ꢀ9 ft.)
1.80 m (5.91 ft.) 10.90 cm (0.36 ft.)
ꢀ.17 m (7.1ꢀ ft.) 13.10 cm (0.43 ft.)
ꢀ.53 m (8.30 ft.) 15.ꢀ0 cm (0.50 ft.)
ꢀ.90 m (9.51 ft.) 17.40 cm (0.57 ft.)
As seen from the side
Lens center
90 inches ꢀ.71 m (8.89 ft.) 3.ꢀ6 m (10.70 ft.) 19.60 cm (0.64 ft.)
100 inches 3.0ꢀ m (9.91 ft.) 3.63 m (11.91 ft.) ꢀ1.80 cm (0.7ꢀ ft.)
1ꢀ0 inches 3.6ꢀ m (11.88 ft.) 4.36 m (14.30 ft.) ꢀ6.10 cm (0.86 ft.)
150 inches 4.54 m (14.90 ft.) 5.46 m (17.91 ft.) 3ꢀ.70 cm (1.07 ft.)
ꢀ00 inches 6.06 m (19.88 ft.) 7.ꢀ8 m (ꢀ3.88 ft.) 43.50 cm (1.43 ft.)
ꢀ50 inches 7.58 m (ꢀ4.87 ft.) 9.11 m (ꢀ9.89 ft.) 54.40 cm (1.78 ft.)
300 inches 9.10 m (ꢀ9.86 ft.) 10.94 m (35.89 ft.) 65.30 cm (ꢀ.14 ft.)
90°
a
a is the distance (m, feet) between the lens and the screen, and corresponds to a range of 0.89 m
(ꢀ.9ꢀ ft.) to 10.94 m (35.89 ft.). H is the height from the image bottom to the center of the lens.
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
PJ WX3231N
Projection size (inches) - 0.758
a (min length) =
a (max length) =
31.022
Projection size (inches) - 0.643
25.845
Screen
As seen from above
Projection distance a
Projection
min length
max length
size
(zooming max) (zooming min)
90°
30 inches 0.94 m (3.08 ft.)
40 inches 1.ꢀ7 m (4.17 ft.)
50 inches 1.59 m (5.ꢀꢀ ft.)
60 inches 1.91 m (6.ꢀ7 ft.)
70 inches ꢀ.ꢀ3 m (7.3ꢀ ft.)
1.14 m (3.74 ft.)
1.5ꢀ m (4.99 ft.)
1.91 m (6.ꢀ7 ft.)
ꢀ.30 m (7.55 ft.)
ꢀ.68 m (8.79 ft.)
As seen from the side
Lens center
80 inches ꢀ.55 m (8.37 ft.) 3.07 m (10.07 ft.)
90 inches ꢀ.88 m (9.45 ft.) 3.46 m (11.35 ft.)
100 inches 3.ꢀ0 m (10.50 ft.) 3.84 m (1ꢀ.60 ft.)
1ꢀ0 inches 3.84 m (1ꢀ.60 ft.) 4.6ꢀ m (15.16 ft.)
150 inches 4.81 m (15.78 ft.) 5.78 m (18.96 ft.)
ꢀ00 inches 6.4ꢀ m (ꢀ1.06 ft.) 7.71 m (ꢀ5.30 ft.)
ꢀ50 inches 8.03 m (ꢀ6.35 ft.) 9.65 m (31.66 ft.)
300 inches 9.65 m (31.66 ft.) 11.58 m (37.99 ft.)
90°
a
a is the distance (m, feet) between the lens and the screen, and corresponds to a range of 0.94 m
(3.08 ft.) to11.58 m (37.99 ft.).
The lens center is in the same level with an image bottom.
ꢀ3
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection
Before connection
• Read the owner’s manual of the device you are connecting to the projector.
• Some computers cannot be used with or connected to this projector.
Check for an RGB and an HDMI output terminal, supported signal
• Turn off the power of both devices before connecting.
•
The figure below shows sample connections. This does not mean that all of these devices
can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)
Video recorder,
DVD player, etc.
Computer
DVD video recorder, etc.
Conversion adapter
To audio
output
White (L)/
Red (R)
To audio
output
White (L)/
Red (R)
To
video
output
To
BNC-pin (not supplied)
To Y/CB/CR output
Green(Y)/Blue(CB)/
Red (CR)
S-video cable
(not supplied)
S-video
output
To RGB output
RGB cable
(supplied)
To audio
output
Video cable
(not supplied)
Monitor cable Mini
D-sub 15P-BNC
(not supplied)
Audio cable
(not supplied)
Audio cable
(not supplied)
Audio cable (not supplied)
HDMI™ cable
(not supplied)
Control
cable (not
supplied)
Audio cable
(not supplied)
Monitor
To RS-ꢀ3ꢀC
terminal
To audio input White
(L)/Red (R)
To HDMI™
terminal
DVD video recorder, etc.
Audio amplifier, etc.
It is necessary to switch
to MONITOR OUT by the
switch. p.18
Computer (for control)
* The connection for COMPUTER 1 IN terminal described here is also applicable for COMPUTER ꢀ IN terminal.
ꢀ4
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
• When COMPUTER ꢀ IN terminal is used as MONITOR OUT terminal, the signal which is
input to COMPUTER 1 IN terminal is output.
• Signals are output from MONITOR OUT terminal even in standby mode.
However, from AUDIO OUT terminal, no audio signal is output.
• A computer monitor cannot accept Y/PB/PR signals correctly.
• The AUDIO IN terminal can be used for devices connected to COMPUTER 1 IN terminal,
COMPUTER ꢀ IN terminal, VIDEO terminal and S-VIDEO terminal.
•
When an AUDIO OUT terminal is connected, sound is not output from the projector speaker.
• Output volume of AUDIO OUT terminal can be adjusted by the VOL button.
• Some devices may not operate properly when connecting with HDMI™.
• For optimal performance, it is recommended that you use an HDMI™ cable with the HDMI
Logo (
).To display a 1080p signal format, you will need a High Speed HDMI™
cable. A conventional HDMI™ cable may not work properly.
• When connecting a network cable, use a shielded cable.
ꢀ5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Turning the power on and off
Connect the power cord
Insert the power cord connector into
the AC IN socket of the projector.
1
2
Insert the power cord plug into a
wall or other power outlet.
The ON/STANDBY indicator flashes green and the
projector enters standby mode.
Power cord connector
(Supplied)
When [Network standby] is set to [On], the ON/
STANDBY indicator lights orange.
Turn the power on
1
Remove the lens cap.
Be sure to remove the lens cap when the power is turned on. If the cap is left on the
projector, it could become deformed due to heat.
Remote
control
Control panel
2
Press the ON/STANDBY button.
The power turns on with a beep sound (if the beep sound
is set to [On]), and the ON/STANDBY indicator flashes
orange, and then flashes green.When [Network standby]
is set to [On], the ON/STANDBY indicator flashes green.
After a moment, the start-up screen appears.
CAUTION
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyesight.
•
Do not block the air intake or exhaust. Doing so could cause a fire due to internal overheating.
Do not place your hands, face, or other objects near the air exhaust, the lamp cover or the
bottom of the unit. Doing so could result in injury and/or damage the object.
•
•
Notes
•
The start-up screen will disappear after a moment.You can also configure the system to
prevent the start-up screen from appearing.To do this, use the Display setting menu
• The first time you use the projector after purchase, after the start-up screen disappears,
p.28
the start menu is displayed
• When [Password] is [On], enter password then the start-up screen is displayed after the
Password entry screen disappears p.35
• Do not touch the lens directly with your hand.
.
.
If fingerprints or stains are left on the projection lens surface, they may interfere with the
projector’s ability to project images on the screen.
ꢀ6
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn the power off
Press the ON/STANDBY button.
1
When the beep sound setting is [On], the projector beeps, and a message appears,
confirming that you wish to shut off the power. To shut off the power, press the ON/
STANDBY button again. If you do not wish to shut off the power, wait for a while without
conducting any operations. The message will disappear after a moment and the
operation will no longer be valid.
Remote
control
2
Press the ON/STANDBY button again.
Control panel
When the beep sound setting is [On], the projector
beeps, and the screen disappears, but the internal
cooling fan continues to operate. The projector will
then go into standby mode.
During cooling, the ON/STANDBY indicator flashes.
While the indicator is flashing, the power cannot be
turned back on. There is no problem with unplugging
the power cord in this state.
3
Replace the lens cap.
After use, replace the lens cap.
Note
• The projector consumes about 4.5 W of power in standby. We recommend that you
unplug the power cord if you will not be using the projector for an extended period.
When [Network standby] is [On], it consumes about 8 W during standby.
Precautions
• If you wish to restart the projector again right after turning off the power, give the lamp
time (about 5 minutes) to cool before plugging it back in. If the lamp overheats, it may
fail to light.
• Right after turning off the power, the unit may become very hot, especially the air
exhaust, lamp cover or bottom of the unit. Please handle with care to avoid burn injuries.
ꢀ7
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic operations
Turn on the power.
Turn on the power by following the instructions in “Turn the power on”
1
p.26
.
Select the language and the lamp power during initial
startup.
2
When the projector is used for the first time after purchase, the start menu for
language selection, lamp power selection and configuration is displayed in English. (If
the screen is out of focus, adjust it according to the step .)
6
1
Use the
then press the
,
,
button to select the desired language and
or
button.
English
Polish
Japanese
French
German
Italian
Norwegian
Finnish
Czech
Chinese (simplified)
Chinese (traditional)
Korean
Spanish
Hungarian
Greek
Danish
Dutch
Rumanian
Indonesian
Thai
Arabic
Portuguese
Russian
Swedish
Turkish
The message for setup confirmation is displayed in the selected language.
Then, the menu for lamp power selection and configuration is displayed. It is
ꢀ
automatically set as Standard. To change the setting, follow the step
.
ꢀ
Use the or
button to select the lamp power and press the
button.
The lamp power, if selected, will be toggled without pressing the
button. The display
automatically disappears in a few seconds.
Notes
• When the projector is turned on the next time, the start menu will not appear upon
the start menu will be displayed the next time the power is turned on.
and Lamp power
• This owner’s manual assumes that English has been selected.
Activate the connected device.
Turn on and start the connected device such as a computer.
3
4
Press the INPUT button.
An image of the connected equipment is projected.
Each time you press the INPUT button, it switches to the input of the connected
equipment that is outputting video signals.
ꢀ8
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
the Input select menu appears if you press the INPUT button. The factory default
setting is [On].
• If the projector is in network input mode and no image is projected after you press
the INPUT button, check that the connected equipment is working, and press the
INPUT button again.
•
If no signal is being output from the connected equipment, pressing the INPUT button
does not change the input and “There is no other input signal.” message will appear.
Adjust projector placement angle.
5
You can adjust the placement angle and the height of the projected image using the
foot adjuster.
1
Lift up the front of the projector to
the desired angle, then press the
foot adjuster release button upward.
The foot adjuster extends. Release the
button to lock the position.
ꢀ
To fine adjust the angle, twist the
foot adjuster.
• To stow the foot adjuster, hold up the
projector while pressing the foot adjuster
release button, then slowly lower the
projector.
Note
• When [Auto keystone] is set to [On] in the Default setting 1 menu, the keystone
distortion will automatically be corrected based on the projector placement angle. If
you do not desire the automatic keystone correction, set [Auto keystone] to [Off].
Adjust the screen size and focus.
6
7
1
Use the zooming lever to adjust the screen size.
ꢀ
Use the focusing lever to adjust the focus.
Adjust the volume with the
buttons.
Front
The speaker volume can be adjusted when an audio signal is
being input.
ꢀ9
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic operations (Continued)
Precautions
•
•
Lamp characteristics may rarely cause the brightness to fluctuate slightly.
The LCD panel is manufactured using high precision technology. There may be black spots
(pixels that do not light) or bright spots (pixels that are constantly lit) on the panel. These
are intrinsic characteristics of the manufacturing technology and are not malfunctions.
Notes
• A lamp is a consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. The
lifetime of the lamp depends on conditions of use.
, any resolutions not
supported by this projector (XGA for X3ꢀ41N, WXGA for WX3ꢀ31N) will be expanded
or shrunk, which will slightly affect image quality. To view high-quality images, set the
computer’s external output to XGA for X3ꢀ41N, WXGA for WX3ꢀ31N.
• With some computer models having LCD or similar displays, displaying images
simultaneously on the projector and the monitor’s display may prevent the images from
displaying properly. If this happens, turn off the computer’s LCD display. For information
on how to turn off the LCD display, see the computer’s owner’s manual.
• A “No signal” message will appear if no signal is being input from the connected
equipment or if signal input is stopped while projecting.
• If a signal not supported by the projector is input, the “Unsupported signal” message
will appear.
• If an unavailable operation button is pressed, the
icon will appear with a beep sound
(if the beep sound is set to [On]).
• Moving pictures played back on computers using DVD software may appear unnatural
when projected with this projector. However, it is not a malfunction of the projector.
LCD Panels
LCD panels wear out. In order to prolong the lifetime of your LCD panel, take the
following precautions:
• To extend the lifetime of the LCD panel, always turn off the power when it is not in use,
and make sure that the lamp is off. Keeping the lamp off will also save electricity.
• If the air filter becomes dirty and clogged, the projector’s internal temperature will rise,
shortening the lifetime of the LCD panel and causing malfunctions. We recommend
• If the air filter becomes damaged, replace it. Contact your sales representative for a
new filter. If you continue to use the projector when its filter is damaged, dust and dirt
will enter the interior and this could cause the projector to stop working or break down.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Using handy features
Remote
control
Using auto setting (For computer input only)
This function automatically sets up the projector to the optimum state.
It sets up the sampling phase, frequency and screen position, etc., for
each type of input signal through a simple operation.
Press the remote control’s AUTO SET button.
The
icon will appear during processing.
You can also set it by selecting [Auto setting] in the Image
Notes
• The image may not be projected or auto adjustment/setting may not be performed
correctly for input signals other than those supported by the projector
• If auto setting fails adjustment, adjust it manually with [Position] in the Image
Correcting the keystone distortion
When the projector placement angle toward the screen is changed while projecting the
image, the picture will undergo keystone (trapezoidal) distortion.
This projector is capable of automatically correcting this keystone distortion based on
the projector’s placement angle.
Before correction
After correction
Remote
control
Adjusting Keystone distortion Manually
Control panel
Use the
buttons for manual keystone
adjustment.
Notes
• Depending on the amount of keystone
adjustment needed and the image content,
some information may be lost, or the picture
quality may suffer.
• Even if [Auto keystone] is set to [On], keystone distortion can be adjusted
manually. Note that if you change the position or angle of the projector, automatic
keystone correction will be performed again.
•
When [Auto keystone] is set to [On], the automatic keystone correction will be
performed each time the power is turned on.
•
Since keystone correction settings are memorized after the power has been turned
off, it is recommended that you first set [Auto keystone] to [Off]. Then if the projector
placement angle against the screen remains unchanged, the keystone adjustment
will also remain unchanged.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Using handy features (Continued)
Resizing image
The projected image can be resized (zoomed in/out).
Press the remote control’s RESIZE
button.
1
Each time you press the RESIZE
button, zoom ratio is up.You can keep
pressing it to enlarge the image further.
To zoom out, press the remote control’s RESIZE
button.
2
Each time you press the RESIZE
button, zoom ratio is
Remote
control
down.You can keep pressing it to reduce the image further.
(However, the image cannot be smaller than the original
size.)
1
2
4
3
To move the area to zoom in, use the
buttons.
You can keep pressing the button until reaching the desired
area.
3
4
When the image returns to the original size by pressing RESIZE
button several times, the zoom will be reset.
Pressing the RETURN button during resizing also resets the zoom.
Notes
• The
icon appears while resizing.
• Operating a function other than Mute will release resizing.
• As zooming is processed digitally, the image quality is degraded in larger zoom
ratio.
• During resizing or moving the zooming area, the image may be distorted.
3ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Cutting off the picture and sound temporarily
Remote
control
(Mute)
When you want to project the images of another projector or overhead
projector temporarily, this projector’s images and sound can be turned
off using the MUTE button.
Press the remote control’s MUTE button or the RETURN/
MUTE button on the projector control panel.
The picture and sound are cut off. (Pressing the MUTE button or
the RETURN/MUTE button again cancels the Mute function and
restores the picture and sound.)
The RETURN/MUTE button on the control panel cannot be used for
muting in the following situations:
• The projected image is resized.
• A menu is displayed.
• USB memory-input is selected.
• Network input mode is selected and no signal is input through the
network.
Notes
• The
icon will appear while mute is in effect.
• Operating any other function will also cancel the muting.
Changing picture mode
Remote
control
The projected image mode can be selected using the NCE button.
Press the remote control’s NCE button and select with the
buttons.
After selection, apply it by pressing the
button.
• For computer, HDMI, USB memory and Network-input images, the
following settings are available.
Dynamic/Standard/Photographic
• For Y/PB/PR, Video and S-video-input images, the following
settings are available.
Vivid/Standard/Cinema
Note
•
You can also change the picture mode using [NCE] of the Image
Remote
control
Changing screen size
The screen size for the projected image can be changed using the
SCREEN SIZE button.
Press the remote control’s SCREEN SIZE button.
Pressing the button switches in turn as follows:
X3ꢀ41N : Normal/Full/Thru/Wide
WX3ꢀ31N : Normal/Full/Thru/4:3 zoom
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Using handy features (Continued)
Notes
• Thru display is available for Computer (including HDMI-input images) and Network-
input images.
• Wide or 4:3 zoom display is available for Y/PB/PR (including HDMI-input images),
Video and S-video-input images.
•
• Using this function on commercial video software, broadcast or cable-broadcasting
except for the purpose of your private viewing and listening may infringe the
copyright protected by the copyright laws.
Freezing the image (Freeze)
This function is used to pause or freeze a video during a presentation.
Remote
control
Press the remote control’s FREEZE button.
The picture will pause. To release the freeze function, press the
FREEZE button again.
Notes
• The
icon will appear while the freeze function is in effect.
• Other operations will also release the freeze function.
• Even if an image is frozen on the projector, the pictures are running
on the video or other equipment.
• Using this function on commercial video software, broadcast or
cable-broadcasting except for the purpose of your private viewing
and listening may infringe the copyright protected by the copyright
laws.
Setting the password
How to change password
The default password is 000000.
Select [Password] in the Default setting 2 menu and press the
button.
or
1
2
3
Select [Password registration] and press the
The password entry screen is displayed.
button.
Enter the current password (6-digit number) using numeric keys of the
remote control.
• Enter [000000] (6 zeros) for the first change.
• The password is not displayed. Instead it appears as [******].
Enter a new password (6-digit number).
4
5
Re-enter the new password for confirmation.
Note
• Please do not forget your password or you will be unable to access the unit. If
that happens, you will need to contact your sales representative.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
How to set password (from [Off] to [On])
1
Select [Password] in the Default setting 2 menu and press the
button.
or
2
3
4
Select [Password setting] and press the
Select [On].
or
button.
Select [OK] and press the
button.
The password entry screen is displayed.
5
6
Enter the password using the numeric keys of the remote control.
The password setting will be set as [On].
How to operate when password is [On]
Turn on the power.
1
2
3
The lamp lights and the password entry screen appears.
Enter the password using the numeric keys of the remote control.
If the entered password is correct, the start-up screen appears and the projector
goes into normal operation. If the password is incorrect, a message will appear
prompting you to re-enter the password, and the password entry screen is displayed
again. If you enter an incorrect password more than 5 times, the projector will
automatically power off and enter standby mode.
Note
• When the password setting is [On], the password function will be enabled only
when the projector is restarted after the power cord has been unplugged.
The password that you set will not be enabled when restarting from standby mode
without unplugging the power cord.
How to set password (from [On] to [Off])
1
Select [Password] in the Default setting 2 menu and press the
button.
The password entry screen is displayed.
or
2
3
4
5
Enter the password using the numeric keys of the remote control.
Select [Password setting] and press the
Select [OFF].
or
button.
Select [OK] and press the
button.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus 1
You can call up on-screen menus, and conduct a number of adjustments and settings using
on the control panel of the main unit and remote control.
Setup using the Setting display
The menu shown below is for operation instructions purposes and might differ from the
actual display.
This will display the Setting display menu.
1. Press the MENU button
2. Select a Category
Select a category by using
There are 5 categories:
.
Displays the current
adjustments and
settings of the selected
category.
Items shown in gray
cannot be adjusted with
the current input source.
p.37
Image adjustment menu
p.39
p.42
p.43
p.45
Display setting menu
Default setting 1 menu
Default setting 2 menu
Status display menu
Press
or
to open the menu.
3. Adjustments & Settings
Item
Adjustment/Setting Value
These marks signify
the items can be
adjusted/set by using
These marks signify
that there are setting
These marks
signify that there
are options.
.
screens. Press
to display a list of
setting screens.
or
Press
or
to display a list of
options.
* When no item is
changed, press
These marks signify the items can
be selected from the list by using
.
.
After an item is selected, apply it by
Toggle items with
Select items with
Fix selection with
.
pressing
.
and press
.
.
• The figure shows displays given for operation instructions purposes. As the display may differ depending
on the item, refer to the following applicable pages for the menu item you desire.
• To return to previous item, press the RETURN button.
• When Network or USB memory input is selected, pressing the MENU button twice displays the Setting
display (2) menu.
4. End Press the MENU button once more.
(The menu will disappear automatically after 30 seconds, if no operation is conducted.)
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
•
Menu adjustments and settings will not be saved, if the power cable is disconnected or
the power goes out before the adjustments and settings have been completed and the
menu display has been closed.
The image adjustment menu
Use this menu to set or adjust image related items. Items that can be set or adjusted
are marked “Yes”, and those that cannot are marked “No”. (When an item is masked, it
indicates that you cannot select it using the current input.)
Item
Contrast
Description
Computer Y/PB/PR HDMI Video S-video Network USB memory
Adjust the image contrast.
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes Yes Yes Yes
Yes Yes Yes Yes
Yes
Yes
No
Lower
Higher
Adjust the brightness of the image.
Brightness
Color
Darker
Adjust the color of the image.
Lighter Deeper
Brighter
No
Yes Yes No
Adjust the sharpness of the image.
Sharpness
Noise
Yes
Yes Yes Yes Yes
Yes
Softer
Sharper
Set the function to reduce
reduction*1 screen noise.
No
Yes
Yes
No
Yes Yes No
No
On (Enable)
Off (Disable)
Switches the picture mode.
Press . Toggle the NCE
NCE
Yes
Yes Yes Yes Yes
Yes
. See
mode with
for details.
Adjust red of the image color.
Less red More red
Adjust green of the image color.
Less green More green
Adjust blue of the image color.
Less blue More blue
Set the black level with
US : NTSC (US) mode
JAPAN : NTSC (JAPAN) mode
R–level
G–level
B–level
Yes
Yes
Yes
Yes
Yes
Yes
Yes Yes Yes Yes
Yes Yes Yes Yes
Yes Yes Yes Yes
Yes
Yes
Yes
.
NTSC
mode*2
No
No
No
Yes Yes No
No
RGB input Set the RGB input range with
range*3
.
Standard : When black color
No
No
Yes
No
No
No
No
becomes lighter.
Full
:
When dark area
becomes too dark.
Automatically adjusts items
such as the sampling phase
depending on the type of
input signal.
Auto
setting
Yes
No
No
No
No
No
No
No
No
No
No
No
No
Equalizer Reduce noise on the screen.
Adjust with
Yes
.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus 1 (Continued)
Item
Description
Computer Y/PB/PR HDMI Video S-video Network USB memory
Press
using
then change mode
and adjust with
Position
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
Phase
Adjust to eliminate flicker.
Frequency
Adjust to eliminate periodic
patterns and flickering when
many fine vertical lines
appear on the screen.
Yes
No
No
No
No
No
No
H-position
Adjust the horizontal position
of the image.
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
V-position
Adjust the vertical position of
the image.
Clamp 1
Adjusts the clamp pulse
position.
Clamp 2
Adjusts the clamp pulse
width.
*1: [Noise reduction] may not work depending on signal type.
*ꢀ: [NTSC mode] can be displayed and adjusted only when the video signal is set to [NTSC] or
[NTSC4.43]. NTSC mode is set to JAPAN when the language is set to Japanese. It is set to US for
other languages.
*3: [RGB input range] can only be set with RGB signals via an HDMITM cable.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
The display setting menu
Use this menu to set screen display related items.
(The items in gray color cannot be set with the current input selection.)
Description
Item
Screen size Screen size setting
or : Enter setting]
X3241N
WX3231N : Normal/Full/Thru/4:3 zoom
[
[
:Selection]
[Enter:
]
: Normal/Full/Thru/Wide
Up/down
shift
Allows the projected images to shift vertically when the screen size setting is
selected Wide for X3ꢀ41N (within the range of 10ꢀ4 x 768) and 4:3 zoom for
WX3ꢀ31N (within the range of 1ꢀ80 x 800).
Lower the image
Raise the image
Blackboard When projecting on a non-screen surface, select a color in accordance with the
mode
projecting surface.
Press and switch with
Select one of the languages below to use for displaying the menu and messages
and
.
Off/Green/Black/Brown/Blue/Beige
Language
[
or : Enter setting]
[
:Selection]
[Enter:
]
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/
/ Indonesia /
/
Background Screen to display when there is no input signal
or : Enter setting] :Selection]
Logo/Blue/None
Display icons as function guides
[
[
[Enter:
]
Icon
On
On
Off
Off
Start-up
screen
Display start-up screen when power is turned on
User logo
Display a logo customized by the user for the start-up screen or when there is no
input signal.
[
or : Enter setting]
Logo registration
Display style
[
: Selection]
Press to display the registration menu.
Background
Black
Press
Yes
Blue
White
Logo confirmation
Reset logo
.
No
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus 1 (Continued)
Detailed description
[Screen size]
• Normal : Enlarges an input image to fit the screen without changing the aspect
ratio of video signals.
• Full
: Displays an input image in 10ꢀ4 × 768 dot resolution by enlarging it to
fill the entire screen. (X3ꢀ41N)
Displays an input image in 1ꢀ80 x 800 dot resolution by enlarging it to
fill the entire screen. (WX3ꢀ31N)
• Thru
• Wide
:
Displays an input image in the native resolution of the video signals. Thru display is
not available for Y/PB/PR, HDMI (Y/PB/PR signal), Video and S-Video-input images.
The larger image than the screen size will be displayed over the screen. The
input image may appear vertically long with some frequencies of video signals.
: Displays an input image in the center of the screen with a 16:9 aspect
ratio by enlarging it to fit the width of the screen. The upper and lower
portions of the image will be compressed.
(X3241N)
Wide display is not available for Computer, HDMI (RGB signal) and Network-
input images.
• 4:3 zoom : Displays an input image with a 4:3 aspect ratio by enlarging it vertically.
The enlarged image will be displayed over the screen. 4:3 zoom display is
not available for Computer, HDMI (RGB signal) and Network-input images.
(WX3231N)
• For Y/PB/PR and HDMI (Y/PB/PR signal) input, screen size setting function is not
available for the video signals with a 16:9 aspect ratio.
For the Network-input images, the size can be set only when the image is displayed.
•
• The size setting is not available when the projector is connected to your computer
using the Network Projector (Windows Vista®, Windows® 7) function. It may fail to
display the image to fill the entire screen with some input image sizes.
• For the USB memory-input images, the size cannot be set.
Note
• Using the screen size setting function on commercial video software, broadcast or
cable-broadcasting programs to display images with the varying aspect ratio except
for the purpose of your private viewing and listening may infringe the copyright
protected by the copyright laws.
[Up/down shift]
Shifts the projected image vertically when [Screen size] is set to [Wide] for X3ꢀ41N.
Shifts the projected image vertically when [Screen size] is set to [4:3 zoom] for WX3ꢀ31N.
[Blackboard mode]
Projects the image in colors similar to projecting on a screen.
Precaution
• The projected image may differ depending on the type, color, and material of the
blackboard and wall even if the selected color is the same as the projected screens.
[Background]
• RICOH is set for [Logo] by factory setting.
• If user’s logo has been registered, it is displayed when [Logo] is set for background.
[Start-up screen]
If user’s logo has been registered and this setting is [On], the logo is displayed at start-up.
[User logo]
Part of the image that is input from a computer is registered as a stationary picture
and is displayed it as a logo at start-up and when no signal is input.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
<Logo registration>
How to register user logo
Project a picture to register.
1
2
Select [User logo] in the Display setting menu, and press the
button.
or
Select <Logo registration> from the displayed menu list and press
3
4
the
button.
The registration area is displayed for confirmation. Select [OK]
and press the
button.
• If the picture does not fall within the display area, use the computer to scroll
the screen.
5
6
Select [Yes] to register and press the
Registration starts.
button.
• A message is displayed while registration is in process.
Notes
• You can register a logo when the input is set to Computer, HDMI (RGB signal),
Network or USB memory.
• For the Network-input, a logo can be registered only when the image is displayed.
• For the USB memory-input, a logo cannot be registered when a thumbnail list is
displayed.
• The area that can be registered is 51ꢀ x 384 dots for X3ꢀ41N and 640 x 400 dots
for WX3ꢀ31N at the center of the screen. To register a company logo, modify the
image within that space.
•
Only one logo can be registered. When a new image is registered, the old one is deleted.
• The time needed to register or display the image varies depending on the data size.
• Using this function on commercial video software, broadcast or cable-broadcasting
except for the purpose of your private viewing and listening may infringe the
copyright protected by the copyright laws.
<Display style>
Select the size of the registered logo.
: Displays the registered image in the original size at center of the screen.
: Displays the registered image by enlarging it fully within the screen.
(As processed digitally, the image quality is degraded.)
<Background>
Sets background color when [Center] is selected for the logo [Display style].
<Logo confirmation>
You can preview the registered logo.
<Reset logo>
You can reset the registered logo, display style and background to the factory
setting. (The logo set for the start-up screen and background is reset.)
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus 1 (Continued)
The default setting menu
This menu shows placement status and other settings.
Default setting 1 menu
Description
Item
Auto keystone Always corrects keystone distortion automatically.
On
Off
No signal
power off
Sets the time to wait for the power to be turned off after the last operation is
made with no input signal.
Off (not turned off)
30 min.
Off
Auto input
search
Sets whether the input with signals is only selected or not.
On
Network input Sets how to detect the Network input when Auto input search is [On].
Always
Normal
detection
Beep
Beeps when operation is made.
On
Off
Voice guide
Power on
Informs the operation status and abnormal conditions.
Off
Small
Loud
Sets whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the power cord is plugged in (Auto).
Manual
Auto
Off
Network standby
Lamp power
Switches on/off the network while the projector is in standby. On
Sets the lamp power.
Low
Standard
Input select menu
Input select
Detailed description
[Auto input search]
Computer 1
Y/PB/PR 1
Computer 2
Y/PB/PR 2
HDMI
Video
S-video
[On]: Automatically searches the signals that can be
projected, and switches input from the connected
device that outputs the video signals each
time the INPUT button is pressed. Input from a
connected device that outputs no video signals
is skipped.
[Off]: Displays the Input select menu.
Toggle with
buttons and press
button.
Network
USB memory
(The input without signals can be also selected.)
Note
• In normal operation, set [Auto input search] to [On].
Set to [Off] when you want to select the input
source from Input select menu, or if the image does
not appear properly.
/
shows whether signal is
input or not.
[Network input detection]
If [Always] is set, even while no images are being sent to the projector through the
Network input, the Network input will be selected when the Auto input search is [On].
If [Normal] is set, the Network input is selected only while images are being sent to
the projector through the Network input.
Note
• It is recommend that you set the [Network input detection] to [Normal] as long as
you do not use the Network input.
•
When the projector is in network input mode and [Network input detection] is set to
[Always], the projector does not switch to another input signal automatically even if [Auto
input search] is set to [On]. Press the INPUT button to switch to another input signal.
4ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
[Voice guide]
Even when you set the [Voice guide] to [Off], it still informs you of the abnormal
conditions.
[Power on]
If [Power on] is set to [Auto] and there is a power outage, the projector will come on
once power is restored.
[Network standby]
When [Network standby] is set to [On], the network is switched to the standby state as
the projector enters standby.While the network is in standby, the projector can be powered
on using the remote control function of the Network Utility. When [Network standby] is
set to [Off], the projector cannot be powered on with the remote control function of the
Network Utility.
[Lamp power]
When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling
fan noise gets quieter.
Default setting 2 menu
Description
Item
Projection
mode
Sets projection mode in accordance with Placement Style.
(Rear)
(Ceiling)
(Rear ceiling)
(Standard)
Fan mode
Sets the cooling fan speed.
Standard
High
Remote control When ꢀ projectors are used and controlled by the remote control respectively,
this menu sets the code for the projector and the remote control.
: Select from 1, 2
[
[
or : Enter setting]
:Select OK to end
[
]
[
: Confirm]
]
Press [Cancel] to return.
Key lock
Lock the control panel buttons.
: Select On/Off
[
[
or : Enter setting]
:Select OK to end
[
]
[
: Confirm]
]
Press [Cancel] to return.
Closed Caption Closed Caption settings.
Press or and switch with
and
.
Off/ CC1/ CC2/CC3/CC4/T1/T2/T3/T4
Reset all
Press . (The password and user logo are not reset.)
Resets all adjustments and settings to their factory settings. Yes
No
Password
Password setting
Press Password registration/Password setting
.
Detailed description
[Fan mode]
Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise
increases.) Set this option to use the projector at high altitude (over 1,500 meters
above sea level).
• Do not set Fan mode to [High] when using the projector at a lower altitude.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus 1 (Continued)
[Remote control]
Sets a remote control code from ꢀ types.You can set each code respectively for up to ꢀ
projectors. The factory setting is [1].
To switch codes, set the same code for the projector and the remote control.
A remote control code is applied after the setting is done.
• You cannot operate the remote control if the codes of the projector and the remote
control do not match.
Remote control code setting for remote control
Set the same remote control code switch as the projector.
[Key lock]
Avoid operating errors by locking the projector’s control panel buttons. (The remote
control operations are still available.)
Control panel operations are locked after the setting is done, and operations using the
control panel buttons are disabled.
• To release the key lock, set the [Key lock] to [Off] using the remote control.You
can also set the [Key lock] to [Off] by pressing the [RETURN/MUTE] button on
the projector for 10 seconds. (When operating the main unit, the LAMP and TEMP
indicators will glow orange for 3 seconds, and the projector will beep.) Note that
when Network or USB memory input is selected, the [Key lock] cannot be set to [Off]
with the [RETURN/MUTE] button on the projector.
[Closed Caption]
• Off
: Closed Caption is not displayed.
• CC1-CC4 : Displays the dialogue and narration of TV programs and videos that are
(Caption) closed captioned.
• T1-T4
:
Displays information not related to the current program, such as weather,
(Text)
stock data or the like, when it is provided by individual station.
Note
• This projector supports a special feature called closed captioning which allows
subtitles to be displayed at the bottom of the picture. This is pursuant to the
Regulations set forth by the US Federal Communications Commission (FCC). Due
to the different broadcasting or signaling system, it may not operate correctly in
other regions or countries where TV programs do not support closed captioning.
• Closed Caption may not appear correctly depending on the signal conditions or the
recording conditions of videotapes.
•
If the Text is not available, only a black rectangle background may appear on screen.
To prevent this from appearing, set the Closed Caption to [Off].
• When you switch channels of broadcasting programs or play a videotape using
“trick play” functions such as rewind or fast-forward, the operations in the connected
device may cause the Caption or Text to remain on the screen for a while.
• Closed Caption is available for Video and S-Video input images.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Displaying Information (Status display)
This displays information about the input signal, lamp use time, etc.
“Yes”: displayed, “No”: not displayed
Item
Input
Description
Computer Y/PB/PR HDMI Video S-video Network USB memory
Input source name
Yes
Yes
Yes
Yes Yes
Yes
Yes
Mode name RGB or HDMI signal mode [Note 1]
Yes
Yes
Yes
Yes
No
No
No
No
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Resolution
Frequency
Sync
Resolution (in dots)
Sync frequency
Sync signal polarity [Note ꢀ]
Signal format Y/PB/PR signal format
No
No
Yes
No
No
No
No
No
No
No
No
No
Video mode Color method of video signal
Yes Yes
Yes Yes
Lamp time
Time of lamp use [Note 3]
Yes
Yes
Yes
Yes
Yes
Lamp reset
count
The count for lamp
replacement
Yes
Yes
Yes
Yes Yes
Yes
Yes
Total time
The total time that this
projector is used.
Firmware version [Note 4]
Yes
Yes
Yes
Yes
Yes
Yes
Yes Yes
Yes Yes
Yes
Yes
Yes
Yes
Version
Notes
are shown.
ꢀ: Sync signal polarity shown as P (positive) or N (negative) for [H/V].
3: Displays [Lamp time] as an estimated measure of when the lamp should be replaced.
(Cannot be used as a counter of guaranteed lamp time.)
4: [Version] shows the version of the projector’s internal control program. This version
will be requested for customer service purposes.
Note
• The displayed information will not be refreshed if the status changes. To refresh the
information, dismiss the display, then display it again.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Network/USB memory
Before connecting via a network
Check your computer’s Operating System before you connect a projector
with your computer via a network.
This projector supports the Network Projector function of Windows Vista® and Windows® 7
features.
• If your computer’s Operating System is Windows Vista® or Windows® 7, and you intend
to use the Network Projector function for network connection, see “Connection using
®
®
p.46
the Network Projector (Windows Vista or Windows 7)”
Network Projector/Network Utility”
, “Setting up the
p.51
p.61
and “Using the Network Projector”
.
•
If your computer’s Operating System is Windows® ꢀ000 or Windows® XP, see “Connection
p.46
p.51
using the Network Utility
”
, “Setting up the Network Projector/Network Utility”
p.64
and “Using the Network Utility
”
.
Connection using the Network Projector (Windows Vista® or
Windows® 7)*
* Now referred to as “Network Projector.”
●
Functions
By using the Connect to a Network Projector wizard, you can connect to any
projectors which support the Network Projector function over a wireless or a wired
network.
You can make a presentation without any connection setting issues.
Notes
•
•
•
This function’s operation has been verified on the Ultimate and Business
editions of Windows Vista®, Professional and Ultimate editions of Windows® 7.
To communicate in Ad hoc mode with a computer over wireless LAN also
requires IP address settings.
In case the resolution of your computer is higher than that of the projector, your
computer must be set at lower resolution.
•
•
Transferring video images and audio sound is not available.
This function does not work while the projector is connected to your computer
using the Network Utility software.
Connection using the Network Utility
●
Functions
The following functions are available with the wired LAN, or via wireless LAN when
p.64
the LAN dedicated application software: [Network Utility]
projector is used.
included with this
1) Displaying a computer’s screen via the projector
The computer’s desktop screen can be sent, as well as the screens of a variety
of software applications, to the projector for display. Likewise, the sound being
played on a computer can also be sent to the projector. Using the Network Mouse
Controller function, you can operate your computer with the projector’s remote
control.
2) Displaying a JPEG file saved on a computer via the projector
JPEG files can be sent to the projector for display.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
3) Displaying a video image saved on a computer via the projector
Video files can be sent to the projector for image display. As well, the sound
stored in the video file is sent to the projector.
4) Displaying computer’s screens via projectors using the
Multiscreen function
This function allows users to display multiple screens by sending data to different
projectors from a single computer by setting up the virtual displays on the computer.
You can also send only the screens that you specify to the projector for display.
5) Operating the projector by means of a computer
Some of the same functions available from the remote control can be performed.
Note
• Network Utility is also operable with Windows Vista® or Windows® 7.
Communication mode
The wireless LAN of this projector supports both Ad hoc and Infrastructure
Communication modes.
Ad hoc communication mode
This is the transmission mode to communicate
between wireless LAN equipment.
This mode is applicable, for example, to a
presentation in the conference room, as it requires
no other facilities. This function can only be used if
the projector is in range of the computer’s wireless signals.
Ricoh does not guarantee the coverage of the radio wave in the form of figures. The
coverage varies depending on the performance of each wireless LAN equipment,
existence of obstacles or other wireless LAN equipment used by nearby working
groups, etc. The coverage is generally estimated on the assumption that wireless LAN
equipment be used in an unobstructed office or conference room.
Infrastructure communication mode
A mixed wireless and wired LAN can be created
To LAN
Internet, etc.
via wireless LAN access points. (Communications
between wireless LAN devices are also allowed.)
Connecting to the rest of the world via a wired
LAN or the Internet generally requires a high level
of security.
Hub
Wireless LAN
access point
Use the appropriate transmission mode for your
network environment.
Caution when using the wireless LAN functions
The Wireless LAN in this unit uses the ꢀ.4 GHz waveband. If there is a similar wireless
LAN in the area, or a wireless device using the ꢀ.4 GHz waveband, or a microwave oven,
the communication efficiency of this apparatus will be reduced, and may become unusable,
but it is not a fault. If this happens, check an area away from the current location that will
not cause radio interference to medical, industrial and public equipment, and change to
it, or stop using the unit.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the USB terminal
This projector can connect to a commercial USB memory device and a USB memory card
reader/writer that are USBꢀ.0 compliant, a digital camera or the like and display the JPEG
p.49
and MPEG files saved in those devices.
(Ricoh does not guarantee the operation of all USB ꢀ.0-compliant devices.)
To connect or disconnect a USB device, use the following procedure:
Connecting USB device
Plug in the USB device.
Make sure the orientation is correct then plug in the USB device until it is secure.
USB device
Disconnecting USB device
1
Switch the input to USB memory and press the MENU button twice to
display the Setting display (2), then select and run [Unplug device] in
the Slideshow setting menu.
The process for disconnecting a USB device starts.
ꢀ
The message “This USB device can be unplugged safely” appears on
the screen.
3
Unplug the USB device.
CAUTION
• Be sure to perform the above steps. Disconnecting a USB during operation may
cause a system malfunction or data corruption.
Notes
• A USB device can be plugged in even when the power is on.
• The projector may not recognize a supported USB device. If that happens, unplug
the USB device then plug it in again.
• The USB terminal does not support the supplied mouse remote control receiver or
a commercial mouse controller.
• A USB hub is not supported.
Precaution
• Disconnecting the power plug while the USB device is operating may cause a
malfunction or data corruption.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
USB memory devices
This projector can read JPEG, MPEG1, and MPEGꢀ (PS) files stored in a USB memory
device and display them on the screen.
This allows you to give presentations without a computer, create an advertising screen
board using the slideshow function, and more. (The projector cannot reproduce
animation effects such as those produced by Microsoft® PowerPoint®.)
The USB terminal
The USB terminal of the projector is USBꢀ.0 compliant and can connect with a USB
memory device, a USB memory card reader/writer, a digital camera and other similar
devices. For USB devices whose operation has been verified, please contact your sales
representative.
Note that this projector does not support all USB memory devices, USB card readers/
writers, and digital cameras.
Backing up data
Ricoh recommends that you back up the data saved in the USB memory device onto
your computer or storage device before use. Ricoh assumes no liability for losses
incurred by data lost through the use of this projector.
Supported files
(1) Supported file extensions are .jpg, .JPG, .jpeg, .JPEG, .mpg, .MPG, .mpeg, and
.MPEG.
(ꢀ) The maximum number including both folders and files is 51ꢀ.
(3) Some JPEG and MPEG files are not supported by this projector.
Regarding JPEG files, the limitations in (3) above can be alleviated by converting the
p.83
JPEG file with the supplied JPEG Conversion Tool
software application.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus 2
Setup using the Setting display (2)
Projector settings (Be sure to read this subsection.)
Using the factory settings as-is may suffer security damage, so be sure to change
the projector settings.
1. Press the MENU button twice
2. Select a Category
The Setting display (2) is displayed.
* Appears only when Network or USB memory input is selected.
Select a category by using
.
Displays the current settings
of selected category.
Item shown in gray cannot
be set with the currently set
conditions of the projector.
The following 5 categories are
available:
Network Projector
p.51
setup
Network utility
setup
p.51
p.57
p.58
p.60
Control setting
Slideshow setup
Status display
Press
or
to open the menu.
3. Make settings
Item
These marks signify the items can be
selected from the list by using
.
After an item is selected, apply it by
pressing
.
The figure shows a typical example. As the display may differ depending on the
item, use the following pages as a reference.
While the video file transfer function of Network Utility or the slideshow function is
in use, the background image of the Setting display (2) does not appear.
4. Back RETURN button
5. End Press the MENU button or RETURN button.
(The menu disappears 30 seconds after the last operation is conducted.)
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the Network Projector/Network Utility
If you select Network Utility, the following items can be set.
Category
Description
Item
Easy Connect
(USB memory)
LAN settings
Wireless
LAN
[Yes
No]
[Enter:
]
Mode: Ad hoc
Infrastructure
SSID: Specify a desired character string (1 to 3ꢀ characters).
[
: Move left or right one character.]
[
to
: Set a character.]
DHCP: Use
Not use
IP address: Enter using the numeric keys of the remote control.
: Move left or right one character.] to : Set a character.]
[
[
Subnet mask: Enter using the numeric keys of the remote control.
: Move left or right one character.] to : Set a character.]
[
[
Gateway: Enter using the numeric keys of the remote control.
[
: Move left or right one character.]
[
to
: Set a character.]
Confirm: [OK] [Cancel] [Enter:
]
Security
Network authentication: Network Authentication Setting
or : Enter setting] : Selection] [Enter:
[
[
]
None/Open/Shared/WPA-PSK/WPAꢀ-PSK
Encryption: Select an encryption type using the
Off/WEP/TKIP/AES
button.
buttons.
Key index: Select a desired number (1 to 4) using the
Network key: Specify a desired character string.
(WEP: 5 to 13 characters, or 10 to ꢀ6 digits in hexadecimal notation)
(TKIP/AES: 8 to 63 characters, or 64 digits in hexadecimal notation)
[
: Move left or right one character.]
Confirm: [OK] [Cancel] [Enter:
Reset all the wireless LAN settings.
[
to
: Set a character.]
]
Setting
Initialization
Confirm: [Yes]
[No]
[Enter:
]
LAN settings
DHCP: Use
Not use
Wired
LAN
IP address: Enter using the numeric keys of the remote control.
: Move left or right one character.] to : Set a character.]
[
[
Subnet mask: Enter using the numeric keys of the remote control.
: Move left or right one character.] to : Set a character.]
[
[
Gateway: Enter using the numeric keys of the remote control.
[
: Move left or right one character.]
[
to
: Set a character.]
Confirm: [OK] [Cancel] [Enter:
]
* To enter characters, use the numeric keypad on the remote control.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus 2 (Continued)
Category
Description
Item
Remote
control
Specify whether to allow the remote control of the projector from a computer.
Appli-
cation
Allowed
Allowed:
Presentation
Forbidden
The projector always accepts remote commands from a
computer.
Presentation: Accepts only the remote commands from the computer
by which an image is projected on the projector (Update
automatically) using Network Utility.
Forbidden:
Always ignores any remote commands from a computer.
WEB browser
Browser authentication: Switch on/off the password authentication for
access to the setting screen using the Projector
Configuration Tool.
On
Off
Password: Enter the password used to access the setting screen when the
Browser authentication is set to On. A character string (1 to 8
characters) can be specified as desired.
[
: Move left or right one character.]
[
to
: Set a character.]
Confirm: [OK] [Cancel] [Enter:
]
* To enter characters, use the numeric keypad on the remote control.
Character entry
Enter characters using numeric keys of the remote control. The character is entered with
a beep sound if the beep sound is set to [On].
Character entry mode
Remote
control
button
Items using characters, numbers, and symbols
(e.g., projector name and destination address)
Number only
“1” “.” “@” “-” “_”
“1”
“ꢀ” “A” “B” “C” “a” “b” “c”
“3” “D” “E” “F” “d” “e” “f”
“ꢀ”
“3”
“4” “G” “H” “I” “g” “h” “i”
“4”
“5” “J” “K” “L” “j” “k” “l”
“5”
“6” “M” “N” “O” “m” “n” “o”
“7” “P” “Q” “R” “S” “p” “q” “r” “s”
“8” “T” “U” “V” “t” “u” “v”
“6”
“7”
“8”
“9” “W” “X” “Y” “Z” “w” “x” “y” “z”
“0” “space!"#$%&'()*+,-./:;<=>?@[\]^_`{|}~”
Deletes one character.
“9”
“0”
Deletes one character.
5ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Details on individual items
• [Wireless LAN settings]
<Easy Connect (USB memory)>
This feature allows users to easily connect the projector to a computer over a network,
without making Wireless LAN settings using Network Utility.
<Mode>
Your projector is set to Ad hoc in the factory. Change the setting if you want to use the
projector in Infrastructure mode.
<SSID>
This is an ID code for connecting to specific individuals over a wireless LAN. This may
also be called “Network group” or “Network name”. Please read the following carefully.
Note: When you use Ad hoc communication mode, if there is a similar SSID network
group (for example, RDPJ1, RDPJꢀ, etc.) in the possible communication area,
it is possible that your projector name will not be displayed in the Network
Utility projector list column. If this is the case, set SSID to a completely different
character string.
Set the following items if you have set the communication mode to Infrastructure.
If you have set the communication mode to Ad hoc for Network Projector setting,
the following items should also be set.
<DHCP>
If you set DHCP to Use, the IP address of the projector is assigned automatically by the
DHCP server. If your network environment does not assign IP addresses automatically,
set DHCP to Not use, then set the following items IP address, Subnet mask and
Gateway manually.
<IP address>
When DHCP is set to Not use, consult with your network administrator for the settings
below and set the IP address manually.
An IP address is a unique number assigned to a terminal. The format is a string of four
dot-separated three-digit numbers. (Example: 111.11ꢀ.xxx.xxx)
Note: If you set the same IP address for wireless LAN with the one for wired LAN,
network function may fail to operate properly.
<Subnet mask>
A subnet mask is used to determine what subnet the IP address assigned to a terminal
belongs to. (Example: ꢀ55.ꢀ55.xxx.xxx)
Note: If you set the same subnet work for wireless LAN with the one for wired LAN,
network function may fail to operate properly.
<Gateway>
This value specifies the IP address of the device, such as a router, to be used to access
servers outside the network. (Example: 111.11ꢀ.xxx.xxx)
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus 2 (Continued)
• [Security for wireless LAN settings]
<Network authentication>
Set the authentication to enhance network security. Select a method identical to that of
the wireless LAN terminal to be connected with.
<Encryption>
Set Encryption according to the setting you made for Network authentication, as
follows.
When you have set Network authentication to Open or Shared, select WEP for
Encryption.
When you have set Network authentication to WPA-PSK/WPA2-PSK, select TKIP or
AES for Encryption.
Note: Network authentication is factory-set to None. If you use the projector with this
setting left unchanged, security may be compromised due to access by a third
party within the projector’s coverage.
<Key index>
When you have set Encryption to WEP, Key index must be set. By default, “1”
is selected. Select a key index identical to that of the wireless LAN terminal to be
connected with.
Note: Since the range of key index varies by product type (1 to 4 or 0 to 3), make
settings with attention.
<Network key>
When you have set Encryption to [WEP]:
• For use at an encryption level of 64-bit, specify a string of 5 arbitrary characters or a
string of 10 characters in hexadecimal notation.
• For use at the 1ꢀ8-bit level, specify a string of 13 arbitrary characters or a string of ꢀ6
characters in hexadecimal notation.
When you have set Encryption to [TKIP]/[AES]:
Specify a string of 8 to 63 arbitrary characters or a string of 64 characters in
hexadecimal notation.
Note 1: Alphabetic characters (A to F, a to f) used in hexadecimal notation are not
case sensitive; the uppercase characters and their lowercase equivalents are
handled to be identical.
Note ꢀ: The longer the strings of characters set for the Network key, the stronger the
encryption becomes, and hence the harder it will be for a third party to decipher
your communications. However, the setting of larger encryption may slow down
communication speed.
Note 3: To set a higher security level, specify a longer string of characters. For
higher security, avoid using a word found in a dictionary and change the key
sometimes.
<Setting initialization>
This item resets the wireless LAN settings to their factory defaults.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
• [Wired LAN settings]
<DHCP>
If you set DHCP to Use, the IP address of the projector is assigned automatically by the
DHCP server. If your network environment does not assign IP addresses automatically,
set DHCP to Not use, then set the following items IP address, Subnet mask and
Gateway manually.
<IP address>
When DHCP is set to Not use, consult with your network administrator for the settings
below and set the IP address manually.
An IP address is a unique number assigned to a terminal. The format is a string of four
dot-separated three-digit numbers. (Example: 111.11ꢀ.xxx.xxx)
Note: If you set the same IP address for wireless LAN with the one for wired LAN,
network function may fail to operate properly.
<Subnet mask>
A subnet mask is used to determine what subnet the IP address assigned to a terminal
belongs to. (Example: ꢀ55.ꢀ55.xxx.xxx)
Note: If you set the same subnet work for wireless LAN with the one for wired LAN,
network function may fail to operate properly.
<Gateway>
This value specifies the IP address of the device, such as a router, to be used to access
servers outside the network. (Example: 111.11ꢀ.xxx.xxx)
• [Application]
<WEB browser>
Browser authentication
Browser authentication and Password are factory-set to Off and no string,
respectively.You should set them as soon as possible.
Password
If you have forgotten your password, set it again using the menu on the main unit.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus 2 (Continued)
Note
• If you select [Network Projector] in the Setting display (2) menu, the same items
in [Network Utility] will be displayed except for the following ꢀ items.
1
[Easy Connect (USB memory)] feature is not available.
ꢀ
In the item [Application], [Password] and [Disconnect] are available as
follows.
Category
Item
Password
Disconnect Disconnect while transferring an image using Network Projector.
[Yes No] [Enter:
Description
Application
Set password
On
Off
]
p.51
See “Setting up the Network Projector/Network Utility”
to conduct
adjustments and settings for Network Projector.
Computer settings
Refer to your computer’s instruction manuals or wireless LAN adapter to perform the
following settings.
• Select Ad hoc (for some wireless LAN adapters, this is Peer-to-Peer Group).
• Set SSID (for some types of wireless LAN adapter, use Network name instead) as
the same as projector’s SSID (at factory shipment, this is set to RDPJ).
• If Encryption, Network authentication, Key index and Network key are set on
the projector, set to the same values.
Note
p.75
• The Easy Connect utility
allows users to easily connect the projector to
a computer over wireless networks, without making wireless LAN settings. For
Easy Connect support, the computer requires a wireless LAN environment that is
NDIS5.1 or higher driver compliant.
Refer to the user’s manual supplied with the wireless LAN adapter or the wireless
LAN embedded computer for more information.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
The control setting menu
This menu sets Projector name, Email function and PJLink function, etc. Select Control
p.50
setting in step ꢀ in “Projector settings”
. The following content will be displayed.
Description
Item
Projector Specify a desired character string (0 to 16 characters).
name
[
or
: Set a character.]
Press [Cancel] to return.
: Enter setting.]
[
: Move left or right one character.]
: Confirm] : Select OK to end]
[
to
[
[
Email
[
: E-mail setting]
[
: Select item]
Status notification: On
Off
SMTP server: Enter a character string using numeric keys of the remote
control.
Port number: Enter a character string using numeric keys of the remote
control.
Destination address: Enter a character string using numeric keys of the
remote control.
Confirm: [OK
: PJLink setting]
PJLink authentication: On
Cancel]
PJLink
[
[
: Select item]
Off
Password: Enter a character string (1 to 3ꢀ characters) using numeric keys of
the remote control.
Confirm: [OK
or : Enter setting.]
: Confirm
Cancel]
Wireless
network
[
[
[
: Select from Enabled, Disabled]
]
[
: Select OK to end]
Press [Cancel] to return.
Detailed description
• [Projector name]
This can be used to identify projectors when communicating with multiple projectors, or
if there is a possibility that another person who is out of communication range will be
using the same projector. It is recommended this is set to prevent incorrect transmission.
• [Email]
<Status notification>: Sends alarm information to the specified E-mail address when
an error such as lamp failure occurs.
<SMTP server>: Set an IP address of the SMTP server.
<Port number>: Enter a port number of the SMTP server.
<Destination address>: Enter within 60 characters. (Example: xxx@xxx.xxx)
• [PJLink]
<PJLink authentication>: Set whether or not to authenticate the user by password
when the projector is accessed via the PJLink-compliant Software Application. (Set [On]
or [Off].)
<Password>: Enter a password for confirmation when the above <PJLink
authentication> is set to [On].
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus 2 (Continued)
Precautions
• When purchased, <PJLink authentication> is set to [Off] and <Password> is not set
by factory setting.You are recommended to make authentication setting as soon as
possible.
• If you forget a password, set it again.
• [Wireless network]
If you set Wireless network to Disabled, the wireless LAN connection will be unusable.
Set Wireless network to Disabled when you do not wish to use the wireless LAN for
network connection.
Note
• The Email function does not support transmission to the SMTP server that requires
authentication.
Setting slideshow options
Slideshow is the function to allow users to display JPEG and MPEG image files saved
in a USB memory device.
If you select Slideshow, the following items can be set.
Category
Item
Description
Auto. demo
On
Off
Still
Image
(Select whether to automatically start a slide show when a USB
memory device is plugged.)
Interval
Select the slide show display interval.
or
: Begin a slide show. Use the
buttons to select.
5 sec./10 sec./30 sec./1 min./3 min./5 min./10 min.
Display effect Select the slide show display effect.
or : Begin a slide show. Use the
None / Wipe / Wipe / Wipe / Wipe
/ Cover / Cover / Cover
buttons to select.
/ Dissolve / Cover
Auto. start
On
Off
Movie
Image
(When a file is selected, start playing the file automatically.)
Repeat
On Off
(Play repeatedly after the end of playing)
Standard Continuous
Switch the form of a thumbnail list.
All File Off
Play icon
Common
Thumbnail
display
Unplug device Run when unplugging a USB device.
Yes No
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Details on individual items
Still Image
• [Auto. demo]
On: A slide show begins automatically when a USB memory device is inserted and
input switches to USB memory. At this time, the JPEG files in the root directory of
the USB memory device are used in the slide show. If the input has already been
switched to USB memory, the slide show begins automatically when the USB
memory device is inserted.
• To pause the slide show, press the
button. Pressing this button again allows
the slide show to begin. To stop the slide show, press the RETURN button.
Off: A list of thumbnails will be displayed when plugging in a USB memory device or
other similar devices. Select a desired file from the list.
Notes
• The Auto Demo function does not work when using a USB memory card reader/
writer to mount multiple media.
• The Auto Demo function is available for JPEG files only.
• [Interval]
You can set the display interval of time (in seconds or minutes) for slide shows to be
played automatically.
Note
• It may take time to display slide show with some files.
• [Display effect]
When playing a slide show, the projector can give various display effects or transitions
to each slide being displayed.
The transitions available are listed below:
• None
Displays each slide with no display effects.
• Wipe
Displays the next slide with a gradual upward (Wipe ), downward (Wipe ), to the left
↑
↓
(Wipe ), or to the right (Wipe ), over the current slide.
←
→
• Dissolve
Displays the next slide gradually in a certain fixed block pattern over the current slide.
• Cover
Displays the next slide as sliding upward (Cover ), downward (Cover ), to the left
↑
↓
(Cover ), or to the right (Cover ), over the current slide.
←
→
Movie Image
• [Auto. start]
On: Start playing a video file automatically when it is selected.
• [Repeat]
On: Repeat automatically from the beginning when the file reaches the end.
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the menus 2 (Continued)
Common
• [Play icon]
The slideshow icon can be displayed.
•
Standard
The projector handles the slideshow icon as follows depending on the “On/Off” setting
of Icon on the projector’s menu.
Icon On: The projector displays the icon upon the start of playing a slide show and
turns it off after a few seconds.
Icon Off: The projector does not display the icon.
Continuous
•
The projector keeps the icon displayed during the slide show.
• [Thumbnail display]
Select the form of a thumbnail list.
All: Displays a thumbnail preview of JPEG files, and if any JPEG files exist in the folder
displays the leading thumbnail image.
File: Displays only a thumbnail image of JPEG files. The thumbnail image of the JPEG
files in the folder is not displayed.
Off: Displays an icon without displaying thumbnail preview.
Note
• Thumbnail image of MPEG files cannot be displayed.
• [Unplug device]
Run when unplugging a USB memory device, a USB memory card reader/writer or a
digital camera and other similar devices.
Checking the projector status
Status display
To check the current status of the projector, select Status display in step ꢀ in “Projector
p.50
settings”
. The following items of information will then be displayed.
Application
The name of the application currently running on the projector is
displayed.
(Examples: Slideshow, Network Utility)
•
•
Details
When inputting from USB memory device
“Free space/Status” are displayed.
When inputting from network
For wireless LAN, “MAC address/Mode/Channel/SSID/
Encryption/IP address/Subnet mask/Gateway” are displayed.
For wired LAN, “Connection status/MAC address/IP address/
Subnet mask/Gateway” are displayed.
•
PJLink class is displayed.
Version
The firmware version number of the network feature and the USB
memory device feature is displayed.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Network Projector
Setting up the projector
Turn the projector power on.
Switch the input to Network.
Make sure to set the projector’s input to Network. If the other inputs are selected, the
projector will not be recognized by the computer.
1
2
A password will be displayed.
A password will be displayed only when [Password] is set to [On] in the Application
category of the Network Projector settings.
3
4
By referring to “Using the menus 2”, make the wireless LAN or wired
LAN settings.
Setting up the computer
Make the wireless LAN or wired LAN settings. Please see the help
function of your computer for details.
5
Open the [Connect to a Network Projector] wizard by clicking the [Start]
button, by clicking [All Programs], then clicking [Accessories], finally
clicking [Connect to a Network Projector].
6
Select the desired projector from the list or enter the projector address.
7
When the password is displayed in step
3
, enter the password.
8
Precaution
• Before connection, be sure that either setting described below has been applied to your
computer.
1) The screen resolution of your computer is set in the following resolution depending on
the projector you are using.
X3ꢀ41N : XGA (10ꢀ4 x 768 dots) or lower
WX3ꢀ31N : WXGA (1ꢀ80 x 800 dots) or lower
ꢀ) Windows Vista® SP 1 (Service Pack 1) has been installed on your computer or your
computer’s operating system is Windows® 7.
• For users of PJ WX3ꢀ31N
If you are unable to set the screen resolution to 1ꢀ80 x 800 with your computer
whose resolution is higher than 1ꢀ80 x 800, set it to lower than 1ꢀ80 x 800
resolution.
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the applications
If you want to use the projector’s internal wireless LAN function, install the Network Utility
on the supplied CD-ROM onto your computer.
System Requirements
Supported Operating System: Windows® ꢀ000, Windows® XP, Windows Vista® (Ultimate,
Business), Windows® 7 (Professional, Ultimate)
CPU:
RAM:
Pentium M 1 GHz or higher recommended
ꢀ56 MB or more recommended
Screen area (resolution): 10ꢀ4 by 768 dots recommended (X3ꢀ41N)
1ꢀ80 by 800 dots recommended (WX3ꢀ31N)
* The system requirements may vary depending on the conditions of use.
Notes
• The Windows® XP, Windows Vista® and Windows® 7 64-bit versions are not
supported.
• Some functions of applications may not be operational with Windows Vista® and
Windows® 7.
Application Types and Major Functions
Network Utility
This application is used for network connections. Use it to send the images from the
computer’s screen to your projector, and display on the screen. In addition, also use it to
transmit the sound being played on a computer to the projector.
JPEG Conversion Tool
Use to convert JPEG and other files into a format that can be displayed as a slide show
using a USB memory device.
How to install
Double-click setup.exe in the Network Utility or JPEG Conversion Tool folder on the
supplied CD-ROM. Follow the on-screen instructions.
If a message appears during installation, please respond to it to continue the installation
process.
When installation is finished, the following shortcuts will appear on your computer’s
desktop:
If a message reporting a firewall block appears, select “Allow access”.
Network Utility
Operations
Operations
→
p.64
JPEG Conversion Tool
→
p.83
6ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
How to uninstall
Uninstall [RICOH Network Utility] and [RICOH JPEG Conversion Tool] programs by
using a program removal utility found in the [Control Panel] on your computer.
Notes
• Your computer screen may temporarily go out during installation, but it is not an error.
• Before beginning installation or uninstallation, you need to log on as Administrator.
• For Windows Vista® and Windows® 7, an error message may appear at the end of
uninstallation when “automatic restart” is selected. However, this is not an error so that
the computer will restart itself and uninstallation process will be completed.
• When using the Network Utility under Windows Vista® or Windows® 7, you must login
as an administrator, or enter the password used at start up by a user with administrator’s
permissions.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Network Utility
Displaying a computer’s screen via the projector
Launch the Network Utility
software application.
1
When the Network Utility launches, the Screen
Image transmission mode window appears on
the computer screen.
To switch to the Screen Image transmission
mode window from another mode, click the
Screen Image icon
.
If a message reporting a firewall block appears,
select “Allow access”.
Select Transmission mode.
2
3
Click Update automatically or Update
manually. See step
Update automatically and Update manually.
6
for the descriptions of
Click the Advanced button.
The Screen Image: Advanced Settings dialog
appears. Set the dialog as shown below, as
necessary.
Interruption
•
Check the No Interruptions checkbox to
prevent other computers from interrupting the
projector, for example, during a presentation.
Window Display
•
Select the Place in Tasktray at the start
of transmission checkbox to iconify the
Network Utility and place it in the computer’s
tasktray when transmission initiated.
To display the window, double click this icon,
or right click and select Open from the popup
menu. Even with the Network Utility window
minimized, you can use the pop-up menu to
stop or resume transmission as described in
step
4
and later.
Transmission Mode (Image)
•
•
Selecting High quality improves the
quality of the projected image, but lowers
communication speed. Selecting High speed
has the opposite effect.
Transmission Mode (Sound)
Check the Transmit sound to a projector (Only when connected with one
projector) checkbox to transmit the sound being played on a computer to the projector.
Note: The sound can be sent when only one projector is connected.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Mouse Controller
•
Check the Control computer mouse pointer using remote control (Only when
connected with one projector) checkbox to control computer mouse pointer
with Mouse control button, PAGE+ button, PAGE - button, L-CLICK button and
R-CLICK button of the projector’s remote control.
Note 1: This function is available when only one projector is connected to computer.
Note ꢀ: When you use the Network Mouse Controller function, do not connect the
mouse remote control receiver to your computer. The function will fail to
operate properly.
Select the Transmission Image you
wish the projector to display.
4
5
Select Desktop
The computer screen image is transmitted as-is.
Select application window
Select a running application (e.g. Microsoft®
PowerPoint®), and send that application’s
window only.
The desktop and a list of running applications are displayed.
Select the desired application from this list. (If the desired
application is not on the list, launch it. Note that if too many
applications are running, it will consume the computer’s
resources, which could slow communication speed.)
Select the projector to be
transmitted.
A list of the names of the projectors you can use
will appear. (If a projector’s name is not specified,
its ID will be displayed instead.) Select the
checkbox of the projector you wish to transmit to
from this list. Then icon
is displayed on the
projector’s screen for a few seconds.
It is possible to select up-to four projectors.
Click the
button.
6
7
When “Update automatically” is selected in step
Screen images are sent consecutively after the
the sound being played on a computer can be sent to the projector.
When “Update manually” is selected in step
2
button is clicked. Besides,
2
A single screen image is sent when the
button is clicked.
To halt transmission from Update automatically, click the
button.
If the Network Utility icon has been placed in the tasktray, double click the icon to
display the window, then halt transmission, or right click the icon, and halt transmission.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Network Utility (Continued)
Notes
•
•
It may not be possible to transmit the images from a movie player or other video applications.
When using “Update automatically”, the transmitted image refresh rate depends on the
performance of the computer you are using and the surrounding radio wave environment.
• The projector screen may have a few differences from the computer screen.
• If you selected application window in step , if that application is not active (in use), the
4
image may not be correctly displayed by the projector.
• The projector ID is the MAC address of the wired LAN inserted into the projector.
• Playing contents protected by copyright is not supported.
• To transmit sound, press the
button then launch the application that plays the
contents including the sound. When you operate the projector using Windows Vista® or
Windows® 7, “Switching audio play device” window may be displayed after pressing
the start button of Network Utility. If this window is displayed, follow the instruction to
switch the audio play device, and then launch the application that plays the contents
including sounds.
• If no sound can be heard from the computer though the connection is stopped, re-
launch the application that plays the contents including the sound.
• Transmission may not be available depending on the sound type.
• Sound cannot be transmitted if multiple projectors are selected.
• The audio signals transmitted by a computer become mono.
• Network Mouse Controller function may not work properly depending on the network
condition.
Displaying a JPEG image saved on a computer via the
projector
Launch the Network Utility software
application.
1
The Screen Image transmission mode window
appears on the computer’s screen.
Click the JPEG File icon
.
2
3
The Network Utility window changes to JPEG File
transmission mode.
Click the Browse button, and select
the file to send.
Clicking the Browse button displays the Open
dialog box. Select the file to send, then click the
Open button.
The selected file is added to the pull-down list in
the Network Utility’s Transmission File field.
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the file to be sent from the
pull-down list of the Transmission
File field.
4
Click the Transmission File field’s
button to
display the pull-down list. Select the file to be sent
from this list.
A thumbnail of the selected file appears in the
Preview box. The file displayed here will be
transmitted.
Step
3
can be skipped.
The way that drag and drop the file to be sent from the desktop or Windows Explorer
into the Preview box is also available. In this case as well, the selected file is added to
the file pull-down list Transmission File field’s.
Select the projector to be
transmitted.
A list of the names of the projectors you can
use will appear. (If a projector’s name is not
specified, its ID will be displayed instead.) Select
the checkbox of the projector to be transmitted
5
6
to from this list. Then icon
is displayed on the
projector’s screen for a few seconds.
It is possible to select up-to four projectors.
Click the
button.
The selected file’s image is displayed by the projector.
Notes
• Only one file can be sent at a time. To send another file, repeat steps
4
and
6
.
• Selecting a file by drag and drop may not be available with Windows Vista® and
Windows® 7.
Displaying a video file saved on a
computer via the projector
Launch the Network Utility
software application.
1
The Screen Image transmission mode window
appears on the computer’s screen.
.
Click Movie File icon
2
The Network Utility window changes to Movie
File transmission mode.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Network Utility (Continued)
Click the Advanced button.
The Movie file: Advanced Settings dialog
appears. Set the dialog as shown below, as
necessary.
3
• Interruption
Check the No Interruptions checkbox to
prevent other computers from interrupting the
projector, for example, during a presentation.
• Transmission Mode (Sound)
Check the Transmit sound to a projector
(Only when connected with one projector)
checkbox to transmit the sound being played on
a computer to the projector.
• Autostart
Check the Start playing the file automatically
when starting transmission checkbox to
automatically start playing the video file when
connecting to the projector.
• Repeat
Check the Play repeatedly after the end of playing checkbox to automatically
repeat from the beginning when the file reaches the end.
Click the Browse button and select
the file to send.
4
Clicking on the Browse button displays the Open
dialog box. Select the file to send then click the
Open button.
The selected file is added to the pull-down list in
the Network Utility’s Select file field.
Select the file to send from the pull-
down list of the Transmission File
field.
5
Click the Transmission File field’s
button to display the
pull-down list. Select the file to send from this list.
A thumbnail of the selected file appears in the
Preview box. The file displayed here will be
transmitted.
Step
4
can be skipped.
The way that drag and drop the file to send from the desktop or Windows Explorer into
the Preview box is also available. In this case as well, the selected file is added to the
pull-down list.
Note
• You may not select a file by drag and drop with Windows Vista® and Windows® 7.
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Select the projector to transmit to.
6
A list of the names of the projectors you can
use will appear. (If a projector’s name is not
specified, its ID will be displayed instead.) Select
the checkbox of the projector to be transmitted
to from this list. Then icon
is displayed on the
projector’s screen for a few seconds.
It is possible to select only one projector.
Click the
button.
7
The selected file’s image is displayed by the projector and the Control window appears
as well.
Play the video file via the Control window.
8
The function of each button and box is as follows:
(Current position):
Indicates the playing position. Dragging the slider
can move the playing position.
(Play):
Starts playing the video file.
The picture is paused.
(Freeze):
(Stop):
Stops playing the video file.
(Volume):
Adjusts sound volume contained in the video file.
(Mute):
Cuts off picture and sound contained in the video file.
(Release mute):
Restores picture and sound contained in the
video file.
Notes
• Only one file can be sent at a time. To send another file, repeat steps
• MPEG/AVI/ASF/WMV files can be transmitted.
5
and
7
.
• Additional software may be required to play MPEGꢀ or ASF files.
• The update speed of the transmitted file depends on your computer’s performance and
the surrounding radio environment.
• The projector ID is the MAC address of the wired LAN mounted on the projector.
• The audio signals transmitted by a computer become mono.
• Playing contents protected by copyright is not supported.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Network Utility (Continued)
Displaying computer’s screens via projectors using the
Multiscreen function
Launch the Network Utility
software application.
1
The Screen Image transmission mode window
appears on the computer’s screen.
Click the Multiscreen icon
The Network Utility window changes to
Multiscreen transmission mode.
.
2
3
4
Select Transmission mode.
Click Update automatically or Update manually. See step
Update automatically and Update manually.
7
for the descriptions of
Click the Advanced button.
The Multiscreen: Advanced Settings dialog
appears. Set the dialog as shown below, as
necessary.
Window Display
•
Select the Place in Tasktray at the start
of transmission checkbox to iconify the
Network Utility and place it in the computer’s
tasktray when transmission initiated.
To display the window, double click this icon,
or right click and select Open from the popup
menu. Even with the Network Utility window
minimized, you can use the pop-up menu to
stop or resume transmission.
Transmission Mode (Image)
•
Selecting High quality improves the
quality of the projected image, but lowers
communication speed. Selecting High speed
has the opposite effect.
Transmission Mode (Sound)
•
Check the Transmit sound to a projector (Only when connected with one
projector) checkbox to transmit the sound being played on a computer to the
projector.
Note: The sound can be sent when only one projector is connected.
Note
• The multi screen function cannot be used with Windows 7.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Mouse Controller
•
Check the Control computer mouse pointer using remote control (Only when
connected with one projector) checkbox to control computer mouse pointer
with Mouse control button, PAGE+ button, PAGE - button, L-CLICK button and
R-CLICK button of the computer’s remote control.
Note 1: This function is available when only one projector is connected to computer.
Note ꢀ: When you use the Network Mouse Controller function, do not connect the
mouse remote control receiver to your computer. The function will fail to
operate properly.
Arrange the virtual display
layout.
5
Clicking the Display Properties button in
the Control window displays the window for
screen display settings.
1
Right click the desired virtual display
(Ricoh DPJ Secondary Display Driver) and
select Attached from the popup menu.
2
Allocate screen displays by drag and drop of
monitor icons.
3
4
Click OK button in the window for screen
display settings, then the Screen Layout
in the Control window will be updated
accordingly.
When you check Switch to the last
screen settings when using next time
the virtual display layout that has been set
will be memorized upon exit from Network
Utility and it will switch to the screen settings
the next time you use the Multiscreen feature.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Network Utility (Continued)
6
Select the projector to transmit to.
A list of the names of the projectors you can
use will appear. (If a projector’s name is not
specified, its ID will be displayed instead.)
Check the checkbox of the projector you wish to
transmit to from this list. And select the virtual
display number that you wish to transmit to from
the pull-down list in the Screen box. Then
icon marked with a number (corresponding to
the screen number) is displayed on the selected projector’s screen for a few seconds.
Up-to four projectors are available to select.
Click the
button.
7
When “Update automatically” is selected in step
3
Screen images are sent consecutively after the
button is clicked. Besides,
the sound being played on a computer can be sent to the projector.
When “Update manually” is selected in step
3
A single screen image is sent when the
button is clicked.
● Multiscreen Usage Examples
Example 1)
While projecting image data sent from your computer on a screen, you can also display
the other image data such as a presenter script on your computer so that you can give a
presentation without showing any image data which you do not wish to let other participants
see.
7ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Example 2)
Using only a single computer, you can make an effective presentation by displaying different
image data stored in the computer via multiple projectors (up to 4 projectors).
[When using ꢀ projectors]
[When using 4 projectors]
This projector is unable to display a divided
single image in large size by combining each
*
display sent by multiple projectors.
Notes
• The figures shown here are illustrated as projectors are connected to a computer via
wireless LAN, however, this also applies for the connection via wired LAN.
• Note the characteristics such as the brightness or the color tint of the projected image
may vary depending on each projector. This is not a malfunction.
CAUTION
When you use multiple projectors with Multiscreen feature, make sure to leave
sufficient space (more than 70 cm) between projectors. If you set the projector near
the air exhaust of the other projector, it may cause damage to other units due to heat.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Network Utility (Continued)
Notes
•
•
It may not be possible to transmit the images from a movie player or other video applications.
When using “Update automatically”, the transmitted image refresh rate depends on the
performance of the computer you are using and the surrounding radio wave environment.
• The projector screen may have a few differences from the computer screen.
• The projector ID is the MAC address of the wired LAN inserted into the projector.
• Playing contents protected by copyright is not supported.
• To transmit sound, press the
button then launch the application that plays the contents
including the sound.When you operate the projector using WindowsVista® or Windows® 7,
“Switching audio play device” window may be displayed after pressing the start button
of Network Utility. If this window is displayed, follow the instruction to switch the audio play
device, and then launch the application that plays the contents including sounds.
• If no sound can be heard from the computer though the connection is stopped, re-launch
the application that plays the contents including the sound.
• Transmission may not be conducted depending on the sound type.
• Sound cannot be transmitted if multiple projectors are selected.
• The audio signals transmitted by a computer become mono.
• Network Mouse Controller function may not work properly depending on the network
condition.
• If you make any changes in the screen display settings of the window without launching
Network Utility, the settings you made will be erased and not be reflected even if you
check Switch to the last screen settings when using next time checkbox.
• For multiscreen function, the images on the computer’s desktop can only be selected
to transmit for display. Note that the application software are not available to select as
transmission images.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
Easy Connect utility
This feature allows users to easily connect the projector to a computer over wireless
networks, without making Wireless LAN settings using Network Utility.
Launch the Network Utility software application and click the Tool button
the Wireless LAN Settings Utility dialog box. Select a desired connection mode in this
dialog box.
to bring up
How to set up with [Simple 1:1 connection]
• Setting on the projector
Turn the projector power on.
Switch the input to Network.
1
2
3
Press the
button on the projector control panel.
• Setting on the computer
Launch the Network Utility software
application.
4
When the Network Utility launches, the
Screen Image transmission mode window
appears on the computer screen.
Click the Tool button
.
5
6
The Wireless LAN Settings Utility dialog
box appears.
Select [Simple 1:1 connection] then
click OK.
The connection starts up.
When a connection confirmation message
appears, proceed as instructed in the
message.
When the connection is complete,
the computer screen image is
7
transmitted.
If the transmission does not start, uncheck the Confirm and immediately transmit
screen image checkbox.
Notes
• This operation is allowed only when the Transmission mode is set to Ad hoc in the
projector’s wireless LAN settings.
• The operation procedure of the projector setting and the computer setting can be altered
without affecting the connection setup, assuming the operation on each side is complete
within 60 seconds.
• Be sure to use Network Utility version 1.0 or later.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Network Utility (Continued)
How to set up with [USB memory connection]
Set up wireless LAN using a commercial USB memory device. For USB devices whose
operation has been verified, please contact your sales representative.
1)Copying the computer settings to the projector
• Setting on the computer
Insert the USB memory device into the
USB terminal slot on the computer.
1
Click the Tool button
of the
2
Network Utility to bring up the
Wireless LAN Settings Utility dialog
box. Select [USB memory connection]
and click OK.
The dialog box for [USB memory connection]
appears.
Select [Projector settings] and click OK,
then enter the required setting items and
click OK.
The setting information is saved to the USB memory
device.
3
4
Unplug the USB memory device from the computer.
To unplug the USB memory device, follow the instructions in the user’s manual
supplied with the USB memory device or the computer.
• Setting on the projector
Turn the projector power on.
Switch the input to Network.
5
6
7
Insert the USB memory device into the projector.
A message appears, notifying that the projector settings have been changed.
The projector name or the projector ID (MAC address of wired LAN)
will be displayed in the projector’s list in the Network Utility window.
8
76
Download from Www.Somanuals.com. All Manuals Search And Download.
2)Modifying the computer settings using the projector settings
• Setting on the projector
Turn the projector power on.
Switch the input to Network.
1
2
3
Press the MENU button twice, then select Easy Connect (USB
memory) in Network Utility settings from the Setting display (2) menu
and press the
button.
When a confirmation window appears, insert the USB memory device
into the projector.
4
5
ClickYes then press the
button.
The wireless LAN settings are saved to the USB memory device. When successfully
saved, a message appears.
Unplug the USB memory device.
6
• Setting on the computer
Launch the Network Utility software
application.
7
8
9
Insert the USB memory device into the
computer.
After a confirmation message appears,
make settings.
When the setting is complete, the projector name of the connected
projector or the projector ID (MAC address of wired LAN) is displayed
in projector’s list in the Network utility window.
Note
• This operation is allowed only when the Transmission mode is set to Ad hoc in the
projector’s wireless LAN settings. Be sure to use Network Utility version 1.0 or later.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Network Utility (Continued)
How to use [Profile settings]
This feature allows the user to save the computer’s wireless LAN settings.
This feature is useful when you need to change wireless LAN settings according to
where you use.
• Advanced setting
This feature allows the user to set details for Easy Connect settings. Make the following
settings as required in this dialog.
• Registering profile automatically
Check this checkbox to automatically register the settings of the Easy Connect as
profile setting data.
• Switching settings automatically at start-up
Check this checkbox to automatically switch to the last used wireless LAN settings
when launching the Network Utility.
• WEB browser
Where the computer and the projector are connected over the network, bring up the
window of Projector Configuration Tool by pressing the WEB browser button.
Precautions
• If the page is not displayed correctly, re-select the projector.
• When the network settings are changed, the network connection is disconnected. If
you wish to reconnect, set up the computer again.
Precaution
• The simple 1:1 connection, the USB memory connection and the profile setting may not
work normally depending on the type of the wireless LAN adapter and the wireless LAN
embedded computer. When such a case arises, use the Network Utility menu to make
necessary wireless LAN settings manually.
78
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating the projector
1
2
This function can be used with any projector input.
Launch the Network Utility software application.
The Screen Image transmission mode window appears on the computer’s screen.
Click the Remote
Control button.
The Remote Control window
appears.
As the Network Utility window is
still displayed, you can operate the
projector via the Remote Control
window, while using the Network
Utility’s functions.
While it is possible to use this function merely to operate the projector, closing the
Network Utility also closes the Remote Control window.
Select the projector to be operated.
3
4
In the Remote Control window, click the
button, and select the
desired projector from the pull-down list. When you make a selection, the
Remote Control window displays as shown in the right figure.
Only one projector can be selected. (It is not possible to operate multiple
projectors.)
Click the Remote Control window’s buttons.
The function of each button and box is as follows:
Power On:
Power Off: Turns projector power off.
Freeze: The picture is paused.
Input (box): Click the
Turns projector power on.
button, and select the desired input from the pull-down list.
Switches to the input selected in the Input box.
Go:
Mute:
Cuts off picture and sound. Click again to restore picture and sound.
Volume +/–: Adjust sound volume.
Resize Off
Restores the picture to its original size.
Resize +/–: Adjusts the enlargement ratio.
:
Move screen (up/down/left/right/diagonal)
To quit, click the
button on the Remote Control window.
5
Performing this does not close the Network Utility window.
To exit both the Network Utility and the Remote Control, click the
Network Utility window.
button on the
79
Download from Www.Somanuals.com. All Manuals Search And Download.
Projecting images stored in a USB memory device
Playing a slide show from a thumbnail list
With Auto. demo set to Off in “Setting slideshow options”, data readout begins when
a USB memory device is inserted and the input switches to USB memory. A list of
thumbnails will then appear on the screen.
The figure below is an example of this process:
Thumbnail list number
Current list No./Total number of lists
Current Folder Name
Current File Name
Operation Guide
Previous page exists
Orange frame: currently
selected file or folder
Folder
Thumbnail image of
first file in folder
JPEG file
MPEG file
Thumbnail
image of file
Next page exists
Symbols in the thumbnail list
Indicates that only folders are inside
the folder.
Indicates that there is no data to
be displayed in the folder.
Indicates that an unsupported
JPEG, MPEG or other file is
present.
Indicates that the first JPEG, MPEG
or other file is not supported.
When the Thumbnail display is set
to Off, the screen appears like this.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Plug a USB memory device.
1
2
Plug in a USB memory device according to the
p.48
procedure in “Connecting USB device”
.
The projector starts loading data from the USB
memory device and displays a thumbnail list on
the screen.
Searching for a target file
• Use the
buttons to move the orange frame over the desired file or
folder.
• If there are multiple pages of thumbnails, click the
button on the bottom row to
go to the next page, and the
button on the top row to go to the previous page.
• To open a folder, move the orange frame to the desired folder and press the
button.You can navigate down 5 levels using the same procedure. Pressing the
RETURN button returns you to the next/other upper level folder.
For JPEG files
Displaying slides
3
• Pressing the
button with a file selected displays the only images in that file in
full-screen view on the screen as a slide. Pressing the
play mode.
button begins automatic
• To return to the thumbnail list display screen, press the RETURN button.
4
5
Changing slides
Pressing the
buttons with a slide displayed changes slides.
(
: previous slide;
: next slide. These buttons are not available during an automatic
play.)
Rotating a slide
Pressing the
buttons with a slide displayed rotates the slide 90 degrees. The
rotation information is preserved as long as you remain in the current folder.
(
: Rotate left;
: Rotate right. These buttons are not available during an automatic
play.)
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Projecting images stored in a USB memory device (Continued)
For MPEG files
Displaying video
3
• Pressing the
button while a file is selected plays only the video image in full-
screen view. Pressing the
button again pauses the video image.
• To return to the thumbnail list display screen, press the RETURN button.
Fast-forwarding and rewinding video images
4
Pressing the
buttons while a video image is displayed fast-forwards or rewinds
the video image.
(
: Fast-forward; : Rewind)
Notes
• The thumbnail display and slide order are listed from the shortest file name to the
longest. If two file names have the same number of characters, they are ordered
numerically if numbers are used in the file name, and alphabetically otherwise.
• It is possible to give presentations without using a computer by converting presentations
created with Microsoft® PowerPoint® into JPEG files using the JPEG Conversion Tool,
p.83
and storing them on a USB memory device.
Note, however, that functions such as animation effects and hyperlinks cannot be used,
so the converted file should be tested before the actual presentation.
• Freeze function cannot be used during slide show or automatic play.
• A slide show is terminated when the input is switched to another.
• With some USB memory devices, the slideshow playback may stop midway. If you
encounter this, use another USB memory device because the current one is not
supported.
• Pressing the GUIDE button on the remote control with a slide or video image displayed
displays the slideshow operation guide.
• When you operate the projector using the USB memory card reader/writer, up to 4
media types are supported.
8ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the JPEG Conversion Tool
The JPEG Conversion Tool converts JPEG files not supported by the projector, image files
in other formats, Microsoft® PowerPoint® files, and other similar files into JPEG files. The
JPEG files converted with this tool can be displayed by sending them using the wireless
p.66
LAN
, or saving them on a USB memory device.
Launching the JPEG Conversion Tool
The window shown in the figure to the right appears on the
computer screen.
Drag the Image Quality Settings slider to the left or right to set
the image quality of the file after conversion. Lower values create
smaller files, but will lower the image quality. (It is not possible to
restore the quality of an image after it has been lowered.)
Converting an image file
This takes JPEG files created with compression formats not supported by the projector, for
example, Windows® metafiles (wmf), and bitmapped files (bmp), and converts into JPEG
files.
(1) In the Conversion Method field, select Converting image
(1)
file. (Status on launch)
(ꢀ) In the File settings field, click the Browse button for Original
Image File Name.
The Open dialog box appears.
(3) In the Open dialog box:
(ꢀ)
(5)
(a) Specify the location of the file to be converted; and
(b) In the Files of Type field, click the
button to select the
file format. A list of files of that format appear in the Open
dialog box.
(7)-(a)
(4) In the Open dialog box, select the file to convert, then
click the Open button.
(5) In the JPEG Conversion Tool window, in the File
settings field, select Browse for File name after
conversion. The Save As dialog box appears.
(6) In the Save As dialog box:
(3)-(a)
(4)
(3)-(b)
(a) Specify the location in which to save the converted
file;
(b) Enter a file name of up to 8 characters in the File
Name field; and
(c) Click the Save button.
(6)-(a)
(6)-(b)
(6)-(c)
(7) (a) In the JPEG Conversion Tool, click the Conversion
button.
(b) The resolution selection dialog box appears. Select a
desired resolution and click the OK button.
(c) A confirmation dialog box opens. Click Yes.
The computer converts the file. When it finishes a
message appears informing you that “a JPEG file has
been created”.
(7)-(b)
(7)-(c)
83
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the JPEG Conversion Tool (Continued)
Converting files created with Microsoft® PowerPoint®
This process provides presentations without using a computer by converting
presentation files created with Microsoft® PowerPoint® into JPEG files, storing them on a
USB memory device, and displaying them in a slide show.
• To use this conversion mode, Microsoft® PowerPoint® must be installed on the
computer.
• Only static images are supported by this process. Animation and audio are not
supported.
Presentation files created with Microsoft® PowerPoint® usually
consist of several slides. For this reason, the tool creates a
folder with the name specified in step (5), below, and file for
(1)
each slide is created in the folder (starting with slide001.jpg).
(ꢀ)
(1) In the Conversion Method field, select Converting PPT file.
(4)
(ꢀ) In the File settings field, click the Browse button for PPT
File Name.
The Open dialog box appears.
(9)-(a)
(3) In the Open dialog box:
(a) Specify the location of the file to be converted; and
(b) Select the PowerPoint® presentation file to convert,
(3)-(a)
then click the Open button.
(4) In the JPEG Conversion Tool window, in the File
(3)-(b)
settings field, click the Create button for New folder
name.
The Folder create dialog box appears.
(5) In the Folder create dialog box, in the Folder Name of
(5)
(6)
document of document field, specify a folder name of 1ꢀ
characters or less.
(8)-(a)
(6) In the Folder create dialog box, click the Selection button.
The Browse for Folder dialog box appears.
(7)-(a)
(7) In the Browse for Folder dialog box:
(a) Specify the location in which to save the folder; and
(b) Click the OK button.
(7)-(b)
(8) In the Folder create dialog box:
(a) Click the Create button.
A confirmation dialog box appears;
(b) Click the OK button.
(8)-(b)
84
Download from Www.Somanuals.com. All Manuals Search And Download.
(9) (a) In the JPEG Conversion Tool window, click the
Conversion button.
(b) The resolution selection dialog box appears. Select a
desired resolution and click the OK button.
(c) A confirmation dialog box opens. Click Yes.
The computer begins to convert the file. When it finishes,
a message appears informing you that “a JPEG file has
been created”.
(9)-(b)
(9)-(c)
Making a presentation with converted JPEG files
(1) Copy the folder created by the JPEG Conversion Tool, and/or its contents, onto a
USB memory device.
(ꢀ) Use step
1
in “Playing a slide show from a thumbnail list” p.80 to display a list
of thumbnails.
(3) Follow the instructions in step
2
in “Playing a slide show from a thumbnail list”
p.80
to find the thumbnail of the first slide, Slide001.jpg, and move the orange
frame to it. (Select Slide001.jpg)
(4) Press the
button on the remote control. An enlarged view of the first slide
appears on the screen. This starts the presentation.
(5) To continue to the next slide, click the remote control’s
previous slide, click the button.
button. To go back to the
85
Download from Www.Somanuals.com. All Manuals Search And Download.
How to use the JPEG Conversion Tool (Continued)
Creating a screen capture and converting it into a JPEG file
This function saves the current computer screen as a JPEG file.
(1) In the Conversion Method field, select Creating screen
capture.
(1)
(ꢀ) In the File settings field, click the Browse button for File
name after conversion.
The Save As dialog box appears.
(ꢀ)
(3) In the Save As dialog box:
(a) Specify the location in which to save the converted file;
(b) Enter a file name of up to 8 characters in the File Name
field; and
(4)-(a)
(c) Click the Save button.
(4) (a) In the JPEG Conversion Tool window, click the
Conversion button.
(3)-(a)
(b) The resolution selection dialog box appears. Select
a desired resolution and click the OK button.
(c) A confirmation message appears. Click Yes.
The computer creates a screen capture, and
converts it into a JPEG file in the specified location. When
it is finished, a message appears to tell you that
“a JPEG file has been created”.
(3)-(b)
(3)-(c)
(4)-(b)
(4)-(c)
Note
• The selected resolution in the dialog box will be the maximum resolution of the
converted image file. Specify the resolution in accordance with your projector’s
resolution.
86
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the projector using a Web browser
How to use the “Projector Configuration Tool”
The “Projector Configuration Tool” uses the Web server features of the projector to set
up the projector using the network.
When using the “Projector Configuration Tool”, set up the Network connecting the
projector and the computer.
p.60
See “Checking the projector status”
to display
1
2
information on the screen and write down the IP address.
Invoke Internet Explorer.
Internet Explorer Ver. 6.0,Ver. 7.0 or Ver. 8.0* is recommended. Enable the Javascript
functions.
* Ricoh does not guarantee the operation for later versions.
In the address bar, enter the IP address “http://xxx.xxx.xxx.
3
xxx/” recorded in step
1
above.
The Web browser will then display the following page.
Menu
Projector name
Projector ID
Note: If you use a proxy server, do not enable the proxy when accessing the above IP
address.
When the wireless LAN is set to use Ad hoc mode, use the WEB browser
function in the Wireless LAN Settings Utility dialog box of Network Utility.
Note
• This function can be enabled using the WEB Browser function in the Wireless LAN
Settings Utility dialog box of Network Utility without specifying the URL into the
browser’s address bar.
87
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the projector using a Web browser (Continued)
Select items from the menu on the left.
4
Settings:
Status Display:
Features:
Top:
Make settings for the Network or USB memory input menu.
Verify the projector state.
Shows the functions available with the Network or USB memory.
Returns you to the top page.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
Details on major items
• Settings
When Browser authentication has been set to On, access to the setup page requires
the input of the password.
The following settings are available for [Wireless LAN], [Wired LAN], [Control
settings] and [Slideshow].
• The items displayed on the screen can be set.
• Enter individual items and press the Execute button to update their setting.
• Status display
Displays some states of the projector.
Projector:
Displays the contents of status display in the Setting display.
Network/USB:
Displays the contents of status display of the Network or USB
memory input in the Setting display (ꢀ).
Maintenance:
Describes an error if it occurs, for example, when the lamp has
blown.
Notes
• Clicking the ? button opens a popup help window.
• The security items such as “Remote control” and “Browser authentication” cannot be
set.
89
Download from Www.Somanuals.com. All Manuals Search And Download.
90
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Lamp replacement
A lamp is a consumable item. If used for extended periods, images will appear dark, and
the lamp could burn out. This is characteristic of a lamp, and is not malfunction. (The
lifetime of the lamp depends on condition of use.) If this happens, replace it with a new one.
WARNING
• If the projector is mounted on the ceiling, it is strongly recommended that you
contact your sales representative when the lamp has to be exchanged. Do not
attempt to replace the lamp by yourself.
If you uncover the lamp while the projector is mounted on a ceiling, there may be
a danger of damage from falling pieces of glass if the lamp is broken, resulting
in possible injury. In addition, working at high elevations can also be potentially
hazardous. Do not attempt to replace the lamp by yourself.
• Always use lamp “PJ Replacement Lamp Type1” (sold separately) when
replacing the lamp.
Using a lamp other than the one specified may cause a malfunction or damage to
the unit due to the difference in the connector shape or the lamp rate.
CAUTION
• If you have been using the projector, the lamp will be very hot, and may cause
burn injuries.
Wait 1 hour or longer for the lamp to cool before replacing it.
• If the lamp should break, please handle with care to avoid injury due to broken
pieces and contact your sales representative for repair service.
91
Download from Www.Somanuals.com. All Manuals Search And Download.
Lamp replacement (Continued)
1
2
Unplug power cord.
Wait until lamp is sufficiently cooled.
Wait for at least 1 hour.
Outer lamp cover
3
Remove the outer lamp cover.
To remove the outer lamp cover, loosen the screw
on the side of the projector, and then slide the
cover out and up (as shown in the illustration).
Inner lamp cover
4
5
Remove the inner lamp cover.
To remove the inner lamp cover, fully remove both
screws, and then lift the cover (as shown in the
illustration). Be careful not to loose the screws.
Pull out the lamp.
Loosen the 3 lamp locking screws, pull up the
handle, and press the tab to remove the lamp.
Tab
Mount the new lamp.
Align the orientation, press down the new lamp
until the bottom is reached. Then lock it in
place using the 3 lamp locking screws.
6
9ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Inner lamp cover
7
Replace the inner lamp cover.
Reattach both screws removed in step
. Tighten the
4
screws until the inner lamp cover is fully immobile.
8
Replace the outer lamp cover.
Reseat the outer lamp cover by sliding it in the direction
Outer lamp cover
of the arrows (as shown in the illustration), and then
tighten the screw loosened in step .Tighten the screw
3
until the outer lamp cover is fully immobile. (The outer
lamp cover must be attached.)
9
Reset the lamp time.
See the lamp’s manual for instructions on resetting the
lamp time.
Notes and Precautions
• The [Lamp time] item in the Status display menu indicates the time of lamp use. (Use
it as a rough estimate or guide for lamp life.)
• Please replace the lamp after ꢀ000 hours of use if [Lamp power] in the Default setting
1 menu is set to [Standard], or after 3000 hours of use if [Lamp power] in the Default
setting 1 menu is set to [Low].
• There may be cases where the lamp stops working before the above mentioned period
expires or before the replacement message is displayed.
• Attach the outer lamp cover correctly so that it is secure and not loose. If it is not
attached correctly, the projector may fail to turn on or the lamp may fail to come on.
• Always replace the lamp with a new one.
•
The lamp is made out of glass. Do not touch the glass surface with your bare hands, bang
it, or scratch it. Since dirt, jolts, scratches and other similar particles may affect the lamp.
About lamp replacement messages
• The lamp replacement message displays an appropriate period based on the
use period selected in [Lamp power].
• When the replacement time approaches, “The lamp life is ending. Please
change the lamp.” message is displayed each time the power is turned on. The
display disappears when you press the
button.
Used Lamps
This projector’s lamp contains trace amounts of environmentally harmful inorganic
mercury. Be careful not to break used lamps, and dispose of them in accordance with
local regulations or contact your sales representative.
93
Download from Www.Somanuals.com. All Manuals Search And Download.
Air filter cleaning
The air filter prevents dust and debris from getting inside the projector. Never run the pro-
jector with the filter removed. It is recommended that you clean the air filter regularly.
• The message “Check the air filter for dirt.” is displayed every 100 hours. (Once the
usage time exceeds 100 hours, the message is displayed for about 30 seconds the first
time the power is turned on and an image is displayed. The message will disappear with
any operation.)
• Check the filter and if any debris is found, use the following cleaning procedure.
WARNING
• Request cleaning and maintenance of a ceiling-mounted unit from your sales
representative.
Attempting to clean or replace the filter in a high location by yourself may cause you
to fall, resulting in injury.
1
2
Unplug power cord.
Remove the air filter.
Pull out the air filter by holding the release knob
with your fingers as shown in the figure.
3
4
Clean the filter.
Carefully remove the dust and dirt from the air filter
with a vacuum cleaner or the like.
Replace the air filter.
Insert the air filter firmly until you hear a click.
Notes
• When dirt and dust build up in the air filter, the air circulation inside the projector is
affected and the internal temperature will rise, causing the projector to stop working or
malfunction.
• Push the air filter fully in. If the projector is used with the air filter only partially inserted,
dust and dirt will enter the interior and this could cause the projector to stop working or
break down.
• If you wash the air filer with water, make sure you dry it thoroughly before replacing it.
• If the air filter becomes damaged, replace it. Contact your sales representative for a new
filter. If you continue to use the projector when its filter is damaged, dust and dirt will enter
the interior and this could cause the projector to stop working or break down.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
Lens and main unit cleaning
WARNING
• Request cleaning and maintenance of a ceiling-mounted unit from your sales
representative. Attempting to clean the unit or replace the lamp in a high location by
yourself may cause you to fall, possibly resulting in injury.
Lens cleaning
• Clean the lens with a commercially available blower
and/or lens cleaner.
• The lens is easily scratched, so do not rub it with hard
objects, or strike it.
Main unit cleaning
• Always unplug the power cord before cleaning the main unit.
• Wipe dirt off the main unit gently using a soft cloth.
• Do not wipe the main unit with a damp cloth.
Doing so may allow water to get inside, resulting in
possible electric shock or unit failure.
• Do not use benzene, thinner or other similar
chemical solutions as they may deform or discolor
the unit or damage the paint surface.
• Do not use a chemically saturated cloth.
95
Download from Www.Somanuals.com. All Manuals Search And Download.
Others
Trouble indications
The indicator illuminates and a beep sounds to inform you of internal abnormalities.
No power
⇒
Problem with projector
• Unplug the power cord, and contact your sales representative.
(OFF)
Lamp went out during use, or won’t come on
Lamp temperature is high so that it is difficult to turn on, the
lifetime of the lamp has ended or the projector is malfunctioning.
• Unplug the power cord and wait for a short while, then turn the
power back on.
⇒
(Red
flashing)
(Red lit)
or
• If a lamp burns out, replace it with a new one.
(Red lit)
(Red lit)
(Red lit)
Power went out during use
Internal overheating, or the outside temperature is too high.
• Make sure the projector is placed so that the air intake and
exhaust are not blocked.
⇒
(Red
flashing)
• Unplug the power cord and wait for a short while, then turn the
power back on.
The
icon will appear before the power goes out.
Power went out during use
Problem with internal cooling fan.
• Unplug the power cord, and contact your sales representative.
⇒
(Green
flashing)
(Red lit)
(Red lit)
The
icon will appear before the power goes out.
Power went out during use, or power won’t come on
The lamp cover is not properly attached.
⇒
(Orange
flashing)
• Unplug the power cord, and reattach the lamp cover.
Power went out during use
Problem inside the projector.
• Unplug the power cord and wait for a short while, then turn the
power back on.
⇒
(Orange lit)
(Red lit)
• If the above action does not clear the problem, unplug the power
cord, and contact your sales representative.
The
icon will appear before the power goes out.
Note
• After there is an abnormal indication, the abnormal status remains until the power cord
is unplugged.
96
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you think something is wrong, check the followings before contacting customer service.
p.96
Please see “Trouble indications”
as well.
If This Happens
Check
No power
• Is the power cord plugged in? Is it connected to the projector?
p.96
Power goes out
during use
• Is the ambient temperature high?
p.96
• Is the air intake or air exhaust blocked?
No picture
No audio
• Is the input source selected correctly? (When [Auto input search]
• Are all the connected devices functioning properly?
• Are all the connected devices functioning properly?
p.100 p.101
Picture not
displayed
correctly
• Is the input signal supported by the projector?
• Is there something generating an abnormal video signal, for
instance the video tape?
p.95
Picture blurred
Part of picture
out of focus
• Is the lens dirty?
• Is the projection distance within the projector’s supported range?
•
Are the sharpness or sampling phase adjustments off?
Image is dark
Colors too light
Bad shading
• Is the screen dirty?
Control panel key
doesn’t work
97
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting (Continued)
If This Happens
Check
Remote control
doesn’t work
• Are the remote control’s batteries drained?
• Are there any obstructions between the remote control and
projector?
• Are there any fluorescent or other bright lights directed at the
projector’s infrared remote sensor?
USB device
images aren’t
projected
• Is the USB memory device inserted correctly?
• Is a USB memory device not supported by the projector inserted?
• Are there any JPEG or MPEG files saved on the USB memory
device?
•
Are the files in an unsupported format or too large for the projector?
For JPEG files, convert them with the supplied software
application.
The wireless LAN • Are the transmission mode, SSID, etc. properly configured?
doesn’t work
• Are there any obstructions between the computer and the
projector?
• Do your computer and operating system support the supplied
software application?
98
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
List of general specifications
Item
Specification
Consumption Power
ꢀ70 W
X3ꢀ41N: ꢀ.0 kg
WX3ꢀ31N: 1.9 kg
Weight
External Dimensions
(including protruding parts)
Cabinet material
ꢀ95 × 8ꢀ × 196 mm (W × H × D)
PC+ABS resin and PC resin (contains Mg alloy in some parts)
Conditions for usage environment Temp: 5°C to 35°C; relative humidity: 30% to 70%
Display method 3-panel transmission
Panel size
X3ꢀ41N: 0.7 type
WX3ꢀ31N: 0.59 type
TFT active matrix
LCD Panel
Drive system
Picture elements
X3ꢀ41N: 786,43ꢀ pixels (10ꢀ4 H × 768 V)
WX3ꢀ31N: 1,0ꢀ4,000 pixels (1ꢀ80 H × 800 V)
X3ꢀ41N
:
F=1.60
–
1.76 f=ꢀ1.5
–
ꢀ5.8 mm
Lens
WX3ꢀ31N: F=1.70 – 1.87 f=19.ꢀ – ꢀ3.0 mm
High-pressure mercury lamp (180 W)
30-300 inches
X3ꢀ41N: 0.89 m – 10.94 m
WX3ꢀ31N: 0.94 m – 11.58 m
1 W (Mono)
Lamp
Projection screen size
Projection distance
Speaker
COMPUTER 1 IN terminal Mini D sub 15 pin RGB / Y/PB / PR (dual use)
Mini D sub 15 pin
RGB / Y/PB / PR / MONITOR OUT (multiple use)
COMPUTER ꢀ IN terminal
HDMI™ terminal
S-VIDEO terminal
VIDEO terminal
HDMI
Mini DIN 4 pin
RCA Pin Jack, 1 V (p-p), 75
Ω
3.5 mm diameter stereo mini-jack: 1.5 V (rms), ꢀꢀ k or more
COMPUTER 1 IN / ꢀ IN/VIDEO/S-VIDEO (multiple use)
Ω
AUDIO IN terminal
AUDIO OUT terminal
CONTROL terminal
3.5 mm diameter stereo mini-jack
D sub 9 pin (RS-ꢀ3ꢀC)
USB ꢀ.0 High-speed enabled Type A;
Output voltage: +5 VDC; Supply current: 500 mA
10BASE-–T/100BASE-TX
USB terminal
LAN terminal *
When connecting a network cable, use a shielded cable.
*
Notes
• This model complies with the above specifications.
• Designs and specifications are subject to change without notice.
• This model may not be compatible with features and/or specifications that may be added
in the future.
Separately sold product
PJ Replacement Lamp Type1
PJ Replacement Air filter Type1
99
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications (Continued)
List of supported signals (Computer input)
This projector supports the following RGB signals. Note, however, that depending on the
computer model, the screen may show flicker or streaking. Please adjust the projector if
this happens.
Refresh rate
(Hz)
H-frequency
(kHz)
Clock
(MHz)
Resolution
Mode
7ꢀ0 x 400
640 x 480
7ꢀ0x400_85
VGA_60
85.039
59.940
7ꢀ.809
75.000
85.008
56.ꢀ50
60.317
7ꢀ.188
75.000
85.061
74.550
60.004
70.069
75.0ꢀ9
84.997
74.700
75.000
59.880
60.000
85.00ꢀ
60.0ꢀ0
75.0ꢀ5
85.0ꢀ4
59.978
60.000
65.000
70.000
75.000
85.000
37.9ꢀ7
31.469
37.861
37.500
43.ꢀ69
35.156
37.879
48.077
46.875
53.674
49.7ꢀ5
48.363
56.476
60.0ꢀ3
68.667
60.134
67.500
49.580
60.000
85.938
63.981
79.976
91.146
65.317
75.000
81.ꢀ50
87.500
93.750
106.ꢀ50
35.500
ꢀ5.175
31.500
31.500
36.000
36.000
40.000
50.000
49.500
56.ꢀ50
57.ꢀ83
65.000
75.000
78.750
94.500
79.857
108.000
83.300
108.000
148.500
108.000
135.000
157.500
1ꢀ1.750
16ꢀ.000
175.500
189.000
ꢀ0ꢀ.500
ꢀꢀ9.500
VGA_7ꢀ
VGA_75
VGA_85
800 x 600
SVGA_56
SVGA_60
SVGA_7ꢀ
SVGA_75
SVGA_85
MAC16"
83ꢀ x 6ꢀ4
10ꢀ4 x 768
XGA_60
XGA_70
XGA_75
XGA_85
MAC19"
115ꢀ x 864
SXGA1_75
WXGA_60
QuadVGA_60
QuadVGA_85
SXGA3_60
SXGA3_75
SXGA3_85
SXGA+
*
1ꢀ80 x 800
1ꢀ80 x 960
1ꢀ80 x 10ꢀ4
1400 x 1050
1600 x 1ꢀ00
UXGA_60
UXGA_65
UXGA_70
UXGA_75
UXGA_85
* : 1ꢀ80 x 800 is only available for WX3ꢀ31N
Note
•
Signals whose resolution exceeds the native resolution mentioned below will be compressed.
For this reason, some information may be lost and/or image quality may be affected.
X3ꢀ41N : 10ꢀ4 x 768 dots
WX3ꢀ31N : 1ꢀ80 x 800 dots
Download from Www.Somanuals.c1om0.0All Manuals Search And Download.
List of supported signals (Y/PB/PR input)
Signal format
fh(kHz)
15.73
31.47
15.63
31.ꢀ5
45.00
37.50
33.75
ꢀ8.13
67.50
56.ꢀ5
fv(Hz)
59.94
59.94
50.00
50.00
60.00
50.00
60.00
50.00
60.00
50.00
480i(5ꢀ5i)@60Hz
480p(5ꢀ5p)@60Hz
576i(6ꢀ5i)@50Hz
576p(6ꢀ5p)@50Hz
7ꢀ0p(750p)@60Hz
7ꢀ0p(750p)@50Hz
1080i(11ꢀ5i)@60Hz
1080i(11ꢀ5i)@50Hz
1080p(11ꢀ5p)@60Hz
1080p(11ꢀ5p)@50Hz
List of supported signals (Video, S-Video input)
Video mode
NTSC
PAL
SECAM
PAL-M
PAL-N
PAL-60
NTSC4.43
fh(kHz)
15.73
15.63
15.63
15.73
15.63
15.73
15.73
fv(Hz)
60
50
50
60
50
60
60
fsc(MHz)
3.58
4.43
4.ꢀ5 or 4.41
3.58
3.58
4.43
4.43
List of supported signals (HDMI input)
Since the resolutions or frequencies input from a computer or picture device vary and may
be different from the signals listed below, the images may not appear correctly or some
signal formats may not be detected properly and even it may fail to display the images. If that
happens, set your computer or the device so that an input signal listed below can be received.
Refresh rate or
V-frequency (Hz)
59.94
H-frequency
(kHz)
Clock
(MHz)
Resolution
Mode
7ꢀ0 x 480
7ꢀ0 x 576
480p(5ꢀ5p)
576p(6ꢀ5p)
7ꢀ0p(750p)
7ꢀ0p(750p)
1080i(11ꢀ5i)
1080i(11ꢀ5i)
1080p(11ꢀ5p)
1080p(11ꢀ5p)
VGA_60
VGA_7ꢀ
VGA_75
SVGA_60
SVGA_7ꢀ
SVGA_75
XGA_60
31.469
31.ꢀ50
45.000
37.500
33.750
ꢀ8.1ꢀ5
67.500
56.ꢀ50
31.469
37.861
37.500
37.879
48.077
46.875
48.363
56.476
60.0ꢀ3
49.580
63.981
65.317
ꢀ7.000
ꢀ7.000
74.ꢀ50
74.ꢀ50
74.ꢀ50
74.ꢀ50
148.50
148.50
ꢀ5.175
31.500
31.500
40.000
50.000
49.500
65.000
75.000
78.750
83.300
108.000
1ꢀ1.750
50.00
60.00
50.00
60.00
50.00
60.00
50.00
59.940
7ꢀ.809
75.000
60.317
7ꢀ.188
75.000
60.004
70.069
75.0ꢀ9
59.880
60.0ꢀ0
59.978
1ꢀ80 x 7ꢀ0
19ꢀ0 x 1080
640 x 480
800 x 600
10ꢀ4 x 768
XGA_70
XGA_75
WXGA_60
SXGA3_60
SXGA+
* 1ꢀ80 x 800
1ꢀ80 x 10ꢀ4
1400 x 1050
* : 1ꢀ80 x 800 is only available for WX3ꢀ31N
Download from Www.Somanuals.c1om0.1All Manuals Search And Download.
Specifications (Continued)
Pin assignment of COMPUTER 1 IN, COMPUTER 2 IN and
MONITOR terminals
Pin description
During RGB input During Y/PB/PR input
11
6
15
10
Pin No.
1
ꢀ
Video signal (R) Color difference signal (PR
Video signal (G) Luminance signal (Y)
)
3
Video signal (B) Color difference signal (PB)
4
GND
*
1
5
5
GND
*
6
7
8
9
10
11
1ꢀ
13
14
15
GND(R)
GND(G)
GND(B)
N.C
GND
GND
GND(PR)
GND(Y)
GND(PB)
Mini D sub 15 Pin connector
Input Signal
*
*
*
*
*
*
*
• RGB input
RGB signals:
0.7 V (p-p) 75
Ω
Horizontal sync signal: TTL level (Pos/neg polarity)
N.C
Vertical sync signal:
TTL level (Pos/neg polarity)
Horizontal sync signal
Vertical sync signal
N.C
• Y/PB/PR input
Y signal:
PB/PR signals:
1.0 V (p-p) 75
0.7 V (p-p) 75
Ω
Ω
Do not connect anything.
*
CONTROL terminal
Pin assignment
Pin No. Signal Name
Description
1
ꢀ
3
4
5
6
7
8
9
DCD
TXD
RXD
DTR
GND
DSR
RTS
CTS
RI
Data carrier detect
Sending data
Receiving data
Data terminal ready
Signal ground
Data set ready
Request to send
Consent to send
Ring indicator
D sub 9 pin connector
Download from Www.Somanuals.c1om0.ꢀAll Manuals Search And Download.
Interface format
1. Communication method
RS-ꢀ3ꢀC, 9600 bps, No Parity, Data Length: 8 bits;
Stop Bit Length: 1 bit
ꢀ. Communication format
3. Data format
STX (0ꢀ h)
Command (3 Byte)
ETX (03 h)
Only 1 command valid per communication.
For input commands, only ASCII-compliant all-
uppercase alphanumeric characters supported.
4. Replies
Acknowledge
ACK (06 h) CR(0 Dh) Data ... Normally ended
ACK (06 h) ESC(1 Bh)
NAK (15 h)
... Aborted
No acknowledge
If commands are to be sent consecutively, wait for the response from the projector
before sending the next command.
Main Commands
Item
Command
PON
Power on
Power off
POF
Icon display on
MO0
Icon display off
MO1
Auto setting (RGB input)
Status display on
Status display off
PAT
DON
DOF
Download from Www.Somanuals.c1om0.3All Manuals Search And Download.
©2011
EN US EN GB
Y007-6300
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Radio Shack Clock Radio 63 955 User Guide
Radio Shack Musical Instrument 32 2058 User Guide
RCA Universal Remote RCU1000B User Guide
Rival Toaster DC SWM169 User Guide
Ryobi Trimmer 725rE User Guide
Samsung Personal Computer DP500A2DK01UB User Guide
Sanyo Refrigerator FPW EXA225 User Guide
Schneider Electric Switch KVM0108A User Guide
Schneider Electric Welder ATV312 User Guide
Senco Music Pedal AST4 User Guide