RDW459FI
Dishwasher
User Guide
&
Installation & Service Instructions
U109982 - 02
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.800-0101 - Introduction
1. Before You Start
At Time of Delivery
Check packaging and dishwasher immediately for signs of
transport damage. If the appliance is damaged DO NOT USE.
Contact your supplier or customer services.
If a Fault Occurs
If the appliance malfunctions, turn off the water supply and
disconnect the plug from the wall socket. If you cannot solve
the problem, contact your service centre.
Please dispose of packaging materials properly.
Only authorised persons should make repairs.
If the supply cord is damaged it must be replaced by the
manufacturer, service agents or authorized persons.
During Installation
•
Site the dishwasher and connect in accordance with the
installation instructions.
To maintain the efficiency and safety of this appliance we
recommend:
•
The dishwasher must not be connected to the electricity
supply while installation is being carried out.
•
Call only Service Centres authorized by the
manufacturer.
•
•
Ensure that the wiring is properly earthed.
•
Always use original spare parts.
The mains electricity supply must conform to the details
shown on the dishwasher nameplate.
Caring for the Environment
Disposing of your packaging
Your new dishwasher was protected by suitable packaging
while on its way to you. All of the materials used are
environmentally friendly for disposal and can be recycled.
Please make a contribution to protecting the environment by
disposing of the packaging appropriately.
•
•
Do not connect the dishwasher to the electricity supply
with an extension cable.
Built-under and built-in appliances should always be
installed under a continuous work surface attached to
adjacent cupboards. This will ensure that the appliance
is stable.
•
•
After the appliance has been installed, the mains plug
should be easily accessible.
Disposing of your old dishwasher
Old appliances still have some residual value. An
environmentally friendly method of disposal will ensure that
valuable raw materials can be recovered and used again.
During installation, the power supply cord must not be
excessively bent or flattened.
During Normal Use
•
When an appliance has reached the end of its working life
unplug it from the mains. Cut off the mains cable and dispose
of it together with the plug.
The dishwasher must only be used for washing
household dishes and cooking utensils.
•
•
This appliance cannot be installed outdoors.
Destroy the door locking mechanism so that children cannot
accidentally lock themselves in.
Do not place any heavy objects or stand on the door
when it is open. The appliance may tip forward.
This symbol on the product or its packaging
indicates that the product may not be treated as
household waste. Instead it should be handed
over your local community waste collection/
recycling centre.
•
•
•
The water inside the dishwasher is NOT suitable for
drinking.
ArtNo.000-019
Do not bin logo
Do not use solvents of any kind inside your dishwasher.
They could cause an explosion.
Open the door very carefully if the dishwasher is
operating.
By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the
environment and human health, which could otherwise be
caused.
•
•
Never touch the dishwasher with wet hands.
If the appliance is not operating properly or
maintenance is required, disconnect from the power
supply.
For more detailed information about recycling of this
product, please contact your local council, your household
waste disposal service or the shop where you purchased the
product.
•
•
Children should be supervised.
Keep detergents out of reach of children.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.800-0203 - Overview - RDW459 diswasher
2. Overview and Operation
Getting to Know Your Dishwasher
Dishwasher Interior (Fig.2-1)
Fig.2-1
�
�
�
�
�
�
1
2
6h 4h 2h
1
2
P
�
��
ArtNo.800-0120 - RDW459 annotated
A
B
C
D
E
Top sprayer
�
Upper rack
�
�
Upper spray arm
Cutlery basket
Lower rack
�
��
F
Control panel
Lower spray arm
Salt container cap
Washing filter
G
H
I
Detergent and rinse aid
dispenser
J
K
L
Water inlet hose
Drain hose
M
Power supply cord
Control Panel (Fig.2-2)
Fig.2-2
�
�
�
�
�
1
2
6h 4h 2h
1
2
P
�
�
�
�
A
B
C
ON-OFF indicator
D
E
½ load indicator light
Programme indicator
Programme button
G
H
I
Low salt indicator light
Delay indicator lights
Delay start button
ON-OFF button
½ load button
F
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Salt
Fig.2-3
The hardness of water varies from place to place. If hard water
is used in the dishwasher, deposits will form on the dishes
and utensils.
No.800-0203 -
salt indicator
The appliance is equipped with a special softener that uses a
salt specifically designed to eliminate lime and minerals from
the water.
Loading the salt into the container
Always use salt intended for use with dishwashers.
The salt container is located beneath the lower rack and
should be filled as follows:
Fig.2-4
1.
When the low salt indicator (Fig.2-3) lights, you must fill
the salt. Remove the lower rack and then unscrew and
remove the cap from the salt container.
Note: If you are filling the container for the first time, fill it
with water
2.
Place the end of the funnel (supplied) into the hole
and introduce about 2 kg of salt. It is normal for a small
amount of water to come out of the salt container.
Water Hardness
Salt
Autonomy
3.
Carefully screw the cap back on.
Clarke
degrees
Selector
position
Level
°dH
mmol/l
consumption (cycles/
IMPORTANT: To prevent the formation of rust, load the salt
cycle
2kg)
just before beginning a wash cycle.
1
2
3
4
0 - 14
14 -36
36 -71
> 71
0 -17
0 - 1.7
0
Adjusting salt consumption
18 - 44 1.8 - 4.4
45 - 89 4.5 - 8.9
–
MED
+
20
60
40
25
The dishwasher is designed to allow for adjusting the amount
of salt consumed based on the hardness of the water used.
This is intended to optimize and customize the level of salt
consumption so that it remains at a minimum.
40
> 89
> 8.9
60
Table 2-1
To adjust salt consumption:
1.
2.
Unscrew the cap from the salt container.
There is a ring on the container with an arrow on it
(Fig.2-4).
3.
If necessary, rotate the ring in an anticlockwise direction
from the ‘–‘ setting towards the ‘+’sign, based on the
hardness of the water being used.
It is recommended that adjustments be made in accordance
with Table 2-1.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Rinse Aid
Fig.2-5
This product makes dishes sparkle and helps them to dry
without spotting. The dispenser is located on the inside panel
of the door.
Loading the rinse aid
To load the rinse aid:
ArtNo.800-207 - Dispenser - Removing the rinp
1.
To open the dispenser, turn the cap in an anti-clockwise
direction and remove (Fig.2-5).
2.
Pour in the rinse aid, making sure not to overfill.
Fig.2-6
Regulate the amount of rinse aid used for each cycle by
turning the dose adjuster (Fig.2-6), located beneath the cap,
with a screwdriver.
There are 6 different settings the normal dosage setting is 3.
ArtNr -
Adjustting
IMPORTANT: Proper dosage of rinse aid improves drying.
If drops of water remain on the dishes or spotting occurs,
the dosage adjuster should be turned to a higher setting. If
the dishes have white streaks, turn the adjuster to a lower
setting.
Fig.2-7
Detergent
Detergent specifically intended for use with dishwashers
must be used. The dispenser must be refilled before the start
of each wash cycle following the instructions provided in the
‘Programme overview’. The detergent dispenser is located on
the inside panel of the door.
ArtNo.800-209 - Dispenser - Detergent compa
Loading the detergent
To load the detergent:
�
�
1.
2.
3.
4.
Open the cover on the dispenser by pressing the button
(Fig.2-7).
Fig.2-8
Pour the detergent for the wash cycle into compartment
‘A’ (Fig.2-8).
Pour the detergent for the prewash cycle into
compartment ‘B’ (Fig.2-8).
After the detergent has been placed in the dispenser,
close the cover and press down until it clicks in place.
ArtNo.800-210 - Dispenser - Loading the dete
Note: To allow the cover to close properly, remove any excess
detergent from the edges of the dispenser.
DO NOT use 3-in-1 or similar tablets when Rapid
Wash and Soak programmes are selected.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergent tablets explained
What you should not put into the
dishwasher
Classic Tabs
Cutlery and tableware manufactured in whole or part from
wood. They become faded and unsightly in appearance.
Furthermore the adhesives that are used are not suitable for
the temperature that occurs inside the dishwasher.
The tab contains Stain Soakers, which dissolve instantly to
soften really dried on food residues such as baked on egg and
cheese sauces.
The blue layer then works to break down and lift off food
remains while the white layer cleans all traces of dirt away for
a spotless and brilliant finish.
Delicate decorative glassware and vases, special antiques or
irreplaceable china. The decorative patterns on such items
will not be dishwasher-proof.
For best results, use with Rinse Aid and Special Salt.
Plastic objects that are not resistant to hot water, copper and
pewter utensils are also not suitable. Decorative patterns
printed or painted onto the surface of crockery, glasses, etc.,
aluminium and silver items tend to become discoloured or
faded if washed in the dishwasher.
Directions: Simply unwrap one tab and place in the detergent
dispenser of your dishwasher. For best results, use with Rinse Aid
and Special Salt.
3-in-1 Tabs
Some types of glass can become opaque in appearance after
they have been washed many times in a dishwasher. Highly
absorbent materials, such as sponges and towels should
never be placed in the dishwasher.
1.
2.
3.
The blue layer contains powerful detergent and Red
Stain Soaker speckles to soften and break down tough
dried-on stains.
The white layer, with its integrated salt function, softens
the water and prevents limescale whilst removing all
traces of residue.
IMPORTANT: Dishes or cutlery that have been soiled by
tobacco ash, wax, grease or paint, should not be put in the
dishwasher.
The 3-in-1 tabs contain a rinse aid ball to deliver a
spotless, streak free brilliant shine.
Damage to glassware and other dishes
Possible causes
Directions: Unwrap one tab and place in the detergent dispenser
of your dishwasher. No need to add additional salt or rinse aid.
The 3-in-1 tab’s salt-action is effective in soft, medium and hard
water up to 21dH (around 95% of households).
•
•
•
Type of glass or manufacturing process
Chemical composition of detergent
Water temperature and duration of dishwasher
programme.
5-in-1 Tabs
1.
The tablet is formulated with powerful detergent and
red Stain Soaker speckles to help penetrate and break
down the toughest baked-on and dried-on stains, even
tea stains.
Suggested remedy
•
Use glassware or porcelain dishes that have been
marked ‘dishwasher-proof’by the manufacturer.
•
Use a mild detergent that is described as ‘kind to dishes’.
If necessary, seek further information from detergent
manufacturers.
2.
3.
Using a rinse aid function, the tab is developed for a
spotless, streak-free sparkling shine.
In the white layer of the tablet, the 5-in-1 tab’s salt-
action prevents limescale deposits in your machine that
can result in residue on your glasses.
•
•
Select a programme with a low temperature and a short
duration.
To prevent damage, take glass and cutlery out of the
dishwasher as soon as possible after the programme has
ended.
4.
5.
Protector Action helps prevent permanent glass
corrosion, a source of cloudy glasses.
The tab gives extra cleaning power to help remove
encrusted stains for a complete clean.
Directions: Simply unwrap one tab and place in the detergent
dispenser of your dishwasher. The 5-in-1 tab’s salt-action
is effective in soft, medium and hard water up to 21dH
(approximately 95% of households).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Arranging Crockery, Glasses, etc. in the
Dishwasher
Fig.2-9
Before placing the dishes in the dishwasher, remove larger
food particles to prevent the filter from becoming clogged,
resulting in reduced performance.
If the pots and pans have baked-on food that is extremely
hard to remove, we recommend that they are soaked before
washed. This will eliminate the need for extra wash cycles.
Pull out the rack to load the dishwasher.
ower rack
Using the lower rack
We recommend that you place the most difficult to clean
items on the lower rack: pots, pans, lids, serving dishes and
bowls (Fig.2-9).
It is preferable to place serving dishes and lids on the sides of
the racks to avoid blocking the rotation of the top spray arm.
Fig.2-10
Pots, serving bowls, etc. must always be placed face down.
Deep pots should be slanted to allow the water to flow out.
WARNING!
�
Knives and other utensils with sharp points must
be loaded in the basket with their points down or
placed in a horizontal position.
�
�
ArtNo.800-0308 - Adjusting the ack
Using the upper rack
�
The upper rack is designed to hold more delicate and lighter
dishware, such as glasses, cups and saucers, plates, small
bowls and shallow pans (as long as they are not too dirty).
Fig.2-11
Fig.2-12
Position the dishes and cookware so that the spray of water
does not move them.
The upper rack can be adjusted for height (Fig.2-10). Undo
the retaining clips on the telescopic runners (A). Slide the rack
out (B), refit on the lower wheels and push back along the
runners (C). Close the retaining clips (D).
Adjust the upper basket to the higher level and you have
more space to accommodate taller pans and trays in the
bottom basket.
ArNo.800-0304 - Using the cup rac
Shelf
Lean tall glasses and those with long stems against the shelf.
DO NOT lean them against other items to be washed.
Place glasses, cups and small bowls on the additional cup
rack. The additional cup rack can be swivelled in or out as
required (Fig.2-11).
Knife rack
The knife rack clips onto the side of the top basket, giving you
the freedom to wash your large sharp knives separately and
out of harm’s way (Fig.2-12).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Dishes
Fig.2-13
Programme selection
The most appropriate programme can be identified by
comparing the type of crockery, cutlery, etc., as well as the
amount and condition of food remains, with the details
contained in Table 2-2, the wash cycle table.
The corresponding programme sequence, duration and
consumption details are shown in the right half of the table.
Fig.2-14
Example: Use the normal programme for dishes and utensils
that are heavily soiled.
Earn savings
P
If only a small number of dishes have been loaded into the
dishwasher, selecting a programme that operates at the next
lowest temperature will usually be sufficient.
ArtNo.800-0229 - RDW459 - Operation 2
Programme data
The stated programme data are based on standard operating
conditions. The values can vary considerably according to:
•
•
•
•
•
•
Different amounts of dishes
Temperature of mains water supply
Pressure of mains water supply
Ambient temperature
Fluctuations in mains voltage
Machine-related factors (e.g. temperature, water
volume)
Switching the dishwasher ON
1.
2.
3.
4.
Turn on the tap.
Open the door.
Set ON-OFF button to ON (Fig.2-13).
Press the programme button, the programme indicator
illuminates (Fig.2-14).
5.
If the door is closed, the programme indicator blinks
and the programme will start automatically.
End of programme
Six beeps will indicate that the wash cycle has finished and all
the programme indicators light.
Switching the dishwasher OFF
Several minutes after the programme has ended:
1.
2.
3.
Open the door.
Set the ON-OFF button to OFF.
Remove dishes, etc. when they have cooled down.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Interrupting the programme
Fig.2-15
A cycle that is underway can be modified if it has only been
running for a short time. Otherwise, the detergent may have
already been used, and the appliance may have already
drained the wash water. If this is the case the detergent
dispenser must be refilled; see ‘Loading the detergent’.
6h 4h 2h
To cancel a programme that is underway, carefully open
the door and press the programme button and hold it in for
about 3 seconds.
Fig.2-16
Caution! There is a risk of water coming out from
inside the appliance. DO NOT open the door fully
6h 4h 2h
6h 4h 2h
until the spray arm has stopped rotating.
�������
�������
When you open the door, the dishwasher will beep ten times
every thirty seconds.
6h 4h 2h
6h 4h 2h
If the appliance has already heated up or the hot water was
switched ON and then the appliance door opened, leave the
door ajar for several minutes and then close.
�������
��������
6hArtNo.8400h-02142- RhDW6012 - Operation 4 timer settings
6h 4h 2h
�������
��������
Delayed start programming
You can delay the start of a programme in increments of
2 hours up to 12 hours.
Fig.2-17
1.
2.
Switch dishwasher ON.
1
Immediately press the Delayed Start button (Fig.2-15),
the delayed start indicator lights, the start time for the
wash cycle can be delayed for 2, 4, 6, 8, 10 or 12 hours
(Fig.2-16).
2
0-021
3.
Press the Delayed Start button as many times as
necessary until the numerical display shows the
required delay.
4.
5.
6.
To cancel the time delay setting, pressing the Delayed
Start button until the delayed start indicator goes out.
Press programme button to choose the desired
programme.
If the door is closed, the delay indicator will blink and
the indicators will go out as the time counts down, the
programme will start until the delayed start indicator
goes out and the wash cycle begins.
½ Load Button
This function allows the dishwasher to wash dishes using only
the upper rack if there are not enough dishes for a full load.
This will allow you to save on water and energy consumption.
To select ½ load:
1.
Select the programme and then press the ½ load button
(Fig.2-17) – the ½ load indicator blinks.
2.
Close the door. The programme starts automatically.
To cancel the ½ load
1.
2.
Open the door slightly.
Press the programme button and hold it in for about
3 seconds.
Please keep in mind that the amount of detergent should also
be adapted to the ½ load.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Memory Function Module
If a power cut occurs while the selected washing program
is active, the program is not cancelled. The controls use a
microprocessor device to memorize the information about
the selected washing program. Once the power is returned
to the machine, the dishwasher will resume from the point it
was interrupted.
Cancelling or modifying a washing
program cycle
1.
To modify or cancel a washing cycle it is necessary
to reset the previous programming, by holding the
programme button for at least 3 seconds. The buzzer
will emit one short warning signal.
2.
If the reset operation was successful, a drain phase
will start. Once the drain phase has ended a new
programme can be selected.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.800-0303 - Care & maintenance - RDW459 dishwasher
3. Looking after your Dishwasher
Care
Fig.3-1
After Every Wash
After every wash, set the ON-OFF button to OFF and leave the
door slightly ajar so that moisture and odours are not trapped
inside.
No.800-0203 -
salt indicator
Before cleaning or performing maintenance isolate
from mains.
Overall condition of appliance
Check that no grease or scale has accumulated on the inside
of the dishwasher. If you discover any deposits: Clean the
interior of the dishwasher thoroughly with a detergent
solution.
Fig.3-2
Dishwasher salt
Check the LOW SALT indicator. Top up with salt, if required
(Fig.3-1).
Filters
The filters prevent larger particles of food in the water from
reaching the pump. These particles may occasionally block
the filters.
ArtNo.80ing the filter 1
When the appliance has finished washing, check the filters for
particles of food and, if required, clean.
Fig.3-3
After undoing the coarse micro-filter (Fig.3-2), the filter unit
can be removed (Fig.3-3). Remove any particles of food and
rinse the filters under running water.
Insert the filter unit and tighten the coarse micro-filter.
ArtNo.800-0502 - Cleaning the filter 2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Spray arms
Fig.3-4
Limescale and remnants of food in the washing water can
block the nozzles in the spray arms and the arm mountings.
Inspect the nozzles in the spray arms for blocked holes due to
remnants of food.
If necessary, pull the lower arm (Fig.3-4) upwards and lift it
off. Unscrew the upper spray arm (Fig.3-5).
ArtNo.800-0505 - Cleaning the lower spray arm
Clean both spray arms under running water.
Refit the spray arms. Ensure that the lower arm has
locked into place and the upper one is screwed tight.
Solvents or Abrasive Cleaning Products
To clean the exterior and rubber parts of the dishwasher, do
not use solvents or abrasive cleaning products. Rather, use
only a cloth and warm soapy water.
Fig.3-5
To remove spots or stains from the surface of the interior, use
a cloth dampened with water and a little white vinegar or a
cleaning product made specifically for dishwashers.
Moving the Appliance
If the appliance must be moved, try to keep it in a vertical
position. If absolutely necessary, it can be positioned on its
back.
Seals
One of the factors that cause odours to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning with a damp sponge will prevent this from
occurring.
��������������������������������������
When You Go on Holiday
When you go on holiday, it is recommended that you
run a wash cycle with the dishwasher empty and isolate
from the mains. Turn off the water supply and leave the
door of the appliance slightly ajar. This will help the
seals last longer and prevent odours from forming within
the appliance.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.800-0403 - Troubleshooting - RDW459 dishwasher
4. Troubleshooting
Resolving minor problems yourself
Fig.4-1
Experience has shown that you can resolve most problems
that occur during normal daily usage yourself, without having
to call out a service engineer. Not only does this save costs
but it also means that the appliance is available to use. The
following list of common occurrences and their remedies
should help you identify the causes of most problems.
��
��
��
��
��
Problems when the unit is switched on
Fig.4-2
Appliance does not start up
•
•
•
•
Fault with fuse in mains electricity supply.
Plug not inserted in wall socket.
Appliance door not closed properly.
��
��
Programme button has not been pressed. Water tap not
turned on.
•
Blocked strainer in water intake hose.
Fig.4-3
Caution: Remember that repairs should only
be carried out by a suitably qualified specialist.
Improper repairs can lead to considerable
equipment damage as well as danger to the user.
Problems with the appliance
��
��
Error display on the programme indicator
•
When the programme indicators A1 and A2 blink
(Fig.4-1). Have you checked if the door is closed
properly?
Fig.4-4
•
When the programme indicators A1, A2 and A3 blink
(Fig.4-2). Have you checked if: the water is turned on
and the hose is connected properly; the water supply
to the house is on and has sufficient pressure; the water
supply hose is crimped or bent, or the filter for the water
supply hose is clogged; the drain hose is too low.
��
•
When the programme indicators A1, A3 and A4 blink
(Fig.4-3). Have you checked if: the drain hose is
crimped or bent, or the drain hose is too high?
•
•
When the programme indicators A1 and A4 blink
(Fig.4-4). Have you checked if the drain hose is too low?
If, after these checks the dishwasher still does not
function or has any other error displayed, press the
programme button and hold it in for about 3 seconds,
then press the ON-OFF button to OFF. Wait a few
minutes then turn the dishwasher back on and try
again. If the dishwasher still does not function and/or
the problem persists, contact the nearest authorized
service centre and provide them with the following
information:
1.
2.
The nature of the problem.
The model type number (Mod...) and serial
number (S/N...), as indicated on the plate located
on the side of the inner part of the door.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Lower spray arm rotates with difficulty
The spray arm is blocked by small items or food remains.
•
•
•
•
•
•
Too many items in the rack.
•
Items in the rack were touching each other.
Not enough detergent was added to dispenser.
Selected wash programme was not intensive enough.
Rotation of spray arm obstructed by dishes, etc.
Lid in detergent compartment cannot be closed
•
•
Detergent compartment has been overfilled.
Mechanism is clogged with remnants of detergent.
Nozzles in spray arm are blocked by remnants of food.
Filters are blocked.
Indicator lamps do not extinguish after washing has
finished
•
•
Filters have been incorrectly fitted.
Waste water pump is jammed.
•
The ON-OFF button is still set to ON.
Remnants of detergent stuck inside dispenser
•
Compartment was damp when it was filled up with
detergent. Compartment must be dry before detergent
is added.
Plastic items are discoloured
•
•
Not enough detergent was added to dispenser.
Detergent has insufficient bleaching properties. Use a
detergent containing a chemical bleaching agent.
Water remains inside appliance after programme has
ended
White stains are left on crockery and glasses have a milky
appearance
•
•
•
Blockage or kind in drainage hose. Pump is jammed.
Filters are blocked.
•
Not enough detergent added to the dispenser
compartment. Amount of rinse-aid set too low.
The programme is still running. Wait for the programme
to end.
•
Although water is quite hard, no salt has been put in
appliance. Water softener set too low.
Problems during washing
•
•
Lid on salt container not screwed tight.
Unusual amount of foam
If you use a phosphate-free detergent, try a detergent
containing phosphates and compare results.
•
•
Normal washing up liquid has been poured into the
rinse-aid container.
Dishes, cutlery, etc. have not been dried
Excess amount of rinse aid. Remove any spilled rinse
aid with a cloth as it could otherwise lead to excessive
foaming during the next washing cycle.
•
Selected programme did not include drying function.
Amount of rinse-aid set too low.
•
Items were removed from dishwasher too soon.
Appliance stops suddenly while washing is taking place
Glasses have a dull appearance
•
•
Electricity supply to appliance has been cut off.
Water supply has been interrupted.
•
•
Amount of rinse-aid set too low.
Tea stains or traces of lipstick have not been completely
removed
Knocking sound can be heard while washing is taking
place
•
Detergent does not have a sufficient bleaching effect.
Washing temperature set too low.
•
A spray arm is knocking against the dishes inside the
appliance.
Traces of rust on cutlery
Rattling sound can be heard while washing is taking place
•
•
•
•
Cutlery is not rustproof.
•
Crockery has not been stacked properly inside the
appliance.
Salt content in washing water is too high.
Lid on salt container not screwed tight.
Salt spilt while filling container.
Knocking sound coming from inlet valves
•
This is caused by the way the water pipes have been
laid and it has no effect upon the way the appliance
functions.
Glasses become clouded and discoloured; coating cannot
be wiped off
•
Unsuitable detergent was used. Glasses are not
dishwasher-proof.
Problems with the dishes, cutlery, etc.
Remnants of food are stuck to the dishes, cutlery etc.
Smears left behind on glasses and cutlery; glasses have
acquired a metallic appearance
•
Dishwasher was not loaded properly. Jets of water could
not reach all parts of the dishes, etc.
•
Amount of rinse-aid set too high.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.800-0503 - Installation - RDW459 dishwasher
5. Installation
Positioning the Dishwasher
Fig.5-1
The dishwasher should be aligned to the front of the adjacent
cabinets, with allowance made for the door thickness. The
dishwasher has water supply and drain hoses that can be
positioned on either to the left or the right.
�
��
�
�
�
�
Before installing the dishwasher into a kitchen cabinet,
holes must not be drilled into the sides, or door, to avoid
compromising the performance and operation of the
appliance.
�
�
A plastic self-adhesive anti-condensation strip is supplied
with the dishwasher. Fix the strip to the underside of the
worktop, along the front edge (Fig.5-1).
Connect up the cold water supply, the drain hose and the
electrical connections (see below) then slide the dishwasher
into the cabinet opening. Make sure the unit sits on the
plastic skids supplied.
Fig.5-2
��������������������
Cold Water Connection
Connect the water supply hose (supplied loose) to the cold
water inlet at the rear. Connect the other end to a ¾“ BSP tap
connector (Fig.5-2). Make sure that the washers are in place
and that it is fastened securely in place.
�����������
IMPORTANT: If the water pipes are new or have not been
used for an extended period of time, run the water for
a while to make sure that the water is clear and free of
impurities BEFORE connecting to the dishwasher. Failure
to carry out this precaution may lead to the water inlet
becoming blocked and causing damage the appliance.
ArtNo.800-0101 - Cold water connection
������
Fig.5-3
Drain Hose Connection
Connect the drain hose the water outlet. Insert the hose into
a drainpipe with a minimum diameter of 40 mm, or let it
run into a sink, making sure to avoid bending or crimping. If
necessary, fit a siphon trap (U-bend) with a connecting piece.
The free end of the hose must be at a height of between 40-
100 cm and must not be immersed in water (Fig.5-3).
�����
����
WARNING! The connecting piece for the siphon trap
(U-bend) must be solidly fastened to the wall to
prevent the drain hose from moving and allowing
water to spill outside the drain (Fig.5-4).
Fig.5-4
������������������
��������������
�����
����
��������
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
Fig.5-5
The dishwasher must be installed by a qualified electrician,
in accordance with all relevant British Standards/Codes of
Practice (in particular BS 7671), or with the relevant national
and local regulations.
WARNING: THIS APPLIANCE MUST BE EARTHED
����������
All external wiring must comply with the IEE Regulations
for the Electrical Equipment of Buildings. Connection to the
electrical supply can be made with either a plug and socket
or be permanently wired via a double pole switch. The
dishwasher is supplied with a 3-core cable.
���������������
������������
Should the plug not fit the socket in your home, it should be
removed and replaced with a suitable plug.
W6
�������������
Note: If the plug is fitted is not suitable, it must be cut off and
disposed of properly. To avoid the risk of electrocution, the
plug must not be left where children might find it and plug it
into a supply socket.
Fig.5-6
Three pin plugs to BS 1363 with a capacity of not less than
13A must be used and fitted with a 13 amp fuse ‘ASTA’
approved to BS 1362.
�
After replacing the fuse the cover must be refitted. If the
cover is lost, the plug must not be used until a replacement
cover has been obtained from your supplier. The colour of the
correct fuse carrier is that of the coloured insert in the base of
the fuse recess, or stated elsewhere on the plug. Always state
this colour when ordering a replacement fuse carrier.
IMPORTANT: The wires in the mains lead are coloured in
accordance with the following code:
�
Green and yellow: EARTH
Blue:
NEUTRAL
LIVE
Brown:
Fig.5-7
Caution: The dishwasher plug must be accessible
even when the appliance is installed as a built-in
unit so that maintenance can be carried out safely.
�
�
Care for the external cable
•
Hold the plug, not the electrical cable, when
unplugging the dishwasher.
•
Make sure that the dishwasher does not trap the electric
cable.
ArtNo.800-0112 - Integrated
•
•
Do not step on the cable.
Avoid damage to the electric cable when moving the
dishwasher.
Damaged electrical cable
If the electrical cable is damaged or worn, switch off the
dishwasher and consult an authorized agent for replacement.
Levelling the Dishwasher
When the unit is in position, adjust the feet to level the
dishwasher. In any circumstance, the dishwasher should not
be inclined more than 2° otherwise the performance may be
affected.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
The adjustable feet allow the dishwasher to be raised up to
870 mm. If the space between the floor and the underside
of the work surface is more than 870 mm, the unit should be
positioned on suitable wooded spacers that should be fixed
to the floor (Fig.5-5).
Fig.5-8
Always use a spirit level to make sure that the appliance
is level left-to-right and front-to-back. If the appliance is
installed on carpet, ensure that there is clearance beneath the
appliance.
ArtNo.800-0111 - Marking
the plate position
Adjust the feet to raise and level the dishwasher to the correct
height (Fig.5-6). Using the tool supplied, adjust the rear feet
via the studs ‘A’ at the front of the appliance. Adjust the front
feet ‘B’ using the spanner provided.
Fig.5-9
To prevent damage to the floor surface, install the appliance
on the plastic skids supplied.
Fitting the Decor Door
Fixing the door panel fittings
ArtNo.800-0105 - Fitting the plastic hooks
Place the template supplied on the back face of the door
panel. Align the top of the template, as identified by the
‘A’arrow, with the top of the door and align the side of the
template with the left-hand edge of the door (Fig.5-7). Using
a pencil or bradawl, mark the positions of the holes closest
the door panel edge.
Fig.5-10
Repeat this step for the right-hand side of the door panel
using the other side of the template.
Align a mounting bracket with the two marks on the lower
left-hand part of the panel. Mark the remaining hole in the
top of the bracket (Fig.5-8) and then remove. Repeat for the
other side.
�
At the points marked, carefully drill 2mm holes to a maximum
depth of 10mm. Take care not to drill through to the front
face of the door panel.
�
Position the two brackets on the panel, with the tab facing
downwards. Using the screws supplied, fix the brackets to the
panel.
Secure the two plastic hooks to the holes at the top of the
ArtNo.800-0106 - Fitting the door
panel (Fig.5-9).
Mounting the door panel to the dishwasher
Insert the top plastic hooks into the slots on the dishwasher
front ‘A’. Carefully slide the panel up the channels until it
stops. Slide the panel downwards ‘B’, moving the bottom of
the panel door so that the bracket tabs locate into the slots in
the dishwasher front (Fig.5-10).
Fig.5-11
Align the top of the door panel with the adjacent cabinets.
Gently open the dishwasher door while supporting the door
panel. Secure the door panel using the screws supplied
(Fig.5-11). Cover the screw heads using the plastic caps
provided.
Note: If you have difficulties fitting the door (for example,
if doors are already fitted to adjoining cabinets) then pull
the dishwasher out slightly to allow for easier access for the
door tabs. With the door fitted, push the appliance back into
position.
ArtNo.800-0107 - Securing the door
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Securing the Dishwasher
Using the two screws supplied, secure the dishwasher to the
Fig.5-12
underside of the worktop (Fig.5-12).
For non-wooden worktops (e.g. marble) two brackets are
provided to allow the appliance to be secured to the sides
of the adjacent cabinets. Secure the appliance using the
two screws at the top of the chassis (Fig.5-13); adjust to the
correct width and then screw to the adjacent side panels
using suitable screws.
ArtNo.800-0114 - Securing the dishwasher
Adjusting the Door Springs
The door balance can be adjusted via two nuts accessed
through the two holes in the top of the front frame
(Fig.5-14). Using the tool supplied, adjust these until the
door remains just open under its own weight and is level
when open.
�������
Fig.5-13
Fitting the Plinth
Cut clearance in the plinth to allow the door to fully open and
seal edges with a suitable silicon sealant to prevent water
ingress (Fig.5-15).
�������
�������
���������
�������
ArtNo.800-0114 - Securing the dishwasher
���������
�������
Fig.5-14
ArtNo.800-011door spr
Fig.5-15
18
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.800-0603 - General information - RDW459 dishwasher
6. General Information
Measures must be taken to ensure that the units that are
subsequently re-sited as freestanding appliances cannot
topple over. This can be achieved by bolting the dishwasher
to the wall or fitting it under a continuous work surface, that
is screwed to the adjacent cupboards.
Fig.6-1
Information on comparability tests
implemented in compliance with
EN 50242
Appliance loaded in accordance with standard specifications.
Ar20 - RDW459 - Uck
Example of loaded dishwasher: See Figs.(6-1) and (6-2).
Capacity:
9 place settings
Light wash
5
Fig.6-2
Comparability programme:
Rinse-aid setting:
Detergent:
25g +5g
Height adjustable top-basket must be inserted in the
uppermost position. If the comparability tests do not fully
comply with EN 50242, e.g. degree of soiling, type of dishes
and cutlery, etc. contact the appliance manufacturer before
starting the test.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.800-0703 - Circuit diagram - RDW459 dishwasher
7. Circuit Diagram
�
�
�
N
L
�
�
F
�
CnL1
PS
�
1
�
IAQS
2
D-ED
EV½
�
�
�
�
ML
3
C
CnP3
EV1
�
1
2
3
4
5
6
7
8
CnP2
12
11
10
9
8
7
6
5
4
3
�
2
�
CnP1
1
�
ISS
4
3
2
1
�
�
�
ArtNo.800-703 - RDW459 - circuit diagram
�
Code Description
Code Description
A
B
C
D
E
F
G
H
I
Wiring box
K
L
Overflow switch
Washing pump
Inlet valve
Power switch
Power indicator
Display panel
Door switch
M
N
O
P
Salt missing switch
Temperature sensor
Control panel
Water level switch
Drain pump
Q
R
S
Heater relay
Dispenser
Temperature limiter
Heating element
Temperature limiter
½ load valve
Softener valve
J
T
20
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.800-0803 - Technical data - RDW459 dishwasher
8. Technical Data
INSTALLER: Please leave these instructions with the user.
DATA BADGE LOCATION: Inside face on the side of the door.
COUNTRY OF DESTINATION: GB/IE
Dimensions
���
���
���
���������
���
�������
��������������������
���
ArtNo.800-0128 - 45 dishwasher dimensions
Connections
Electric
220 – 240V 50Hz
Ratings
Energy efficiency class on a scale of A (more efficient) to G (less efficient)
Standard cycle used
A
Light wash
Energy consumption
0.80kWh
Cleaning performance class
Drying performance class
Capacity
A
A
9 place settings
Water consumption
14 litres
Estimated annual consumption
Noise level
Energy: 176kWh; Water: 3080 litres
52dB
10A
Maximum rated current
Maximum total electric load at 230V
2.15kW
21
Download from Www.Somanuals.com. All Manuals Search And Download.
DocNo.000-0001 - Back cover Rangemaster
����������������������������������������
ANo.000-0003 E logo
Download from Www.Somanuals.com. All Manuals Search And Download.
|