63-1090
The main unit requires three AA alkaline batteries
and the remote sensor requires two AAA alkaline
batteries for power. None are supplied; all are
available at RadioShack or online at
1. Remove the battery compartment covers from the
main unit and remote sensor, respectively. If you are
using more than one sensor, select a different channel
for each sensor by switching CHANNEL 1 2 3.
RESET
large display wireless
indoor/outdoor thermometer
Thank you for purchasing your Large Display Wireless
Indoor/Outdoor Thermometer from RadioShack. You can
mount it on a wall or place it on a flat surface using the
included stand. Your thermometer can collect and display
indoor and outdoor temperature and humidity readings
from up to three sensors, and forecast weather.
2. Place the appropriate batteries in each compartment,
following the polarity symbols (+ and -) marked
inside.
For best results, always install batteries
NOTE
in the remote sensor first, and then in the
main unit.
CHANNEL 1 2 3
RESET
3. Reset each unit and replace the battery compartment
covers.
SNOOZE
ꢀ
and ꢁ
Increase or decrease
setting and activate or
deactivate the Atomic
Clock.
on flat surfaces
Place the main unit indoors and the remote sensor
outdoors. Place them on flat surfaces using their
respective stands (included).
MODE
Use to change the
display and settings.
wall mounting
1. Select an indoor wall for your main unit and an
Keyhole
Slot
outdoor wall for your remote sensor.
((•))
2. Remove the stands from the main unit and
remote sensor, respectively.
Set alarm or view alarm
status.
Weather Forecast and
Barometric Trend Area
2. Drill a hole in the wall.
3. Thread a screw (not supplied) into the hole,
letting it extend about 3/16” from the wall.
ꢀ
Turn alarm on or silence
it for 24 hours.
4. Fit the head of the screw into the appropriate
keyhole slot.
Outdoor Temeprature
and Humidity Area
Stand
CHANNEL
Switch remote sensors.
MEMORY
View current, maximum,
and minimum
Indoor Temperature and
Humidity Area
This clock shows the current time and the day
of week in English, French, German, Italian,
or Spanish. The US Atomic Clock in Boulder,
Colorado, automatically updates the information
when the main unit is within 932 miles of a signal.
Initial reception takes 2—10 minutes. It is initiated
when you first set up the unit and whenever you
press RESET. Once complete, the reception icon
will stop blinking.
setting your alarm
This product is equipped with a 2-minute
crescendo alarm.
temperature and
humidity readings.
Clock and Alarm Area
1. Press ((•)) to switch to the alarm display.
PRESSURE
Change pressure
measurement units.
2. Press and hold ((•)) again for 2 seconds. The
alarm hour digits blink.
3. Press UP or DOWN to change settings. Press
((•)) to confirm.
°C/°F
Select temperature
units.
1. Press and hold MODE for 2 seconds. The time
zone blinks.
activating your alarm
Press ꢀ to activate or deactivate the alarm. ꢀ
shows in the clock and alarm area when the alarm
is activated.
2. Press MODE to select the time zone, hour,
minute, year, month, day, and language. Press
ꢀor ꢁto set your desired setting. Press
MODE to confirm.
silencing your alarm
When the alarm sounds, it will continue for 2
minutes. Press SNOOZE to silence it for 8 minutes.
Or, press ꢀ to turn it off until the next day.
The language options are E (English),
F (French), D (German), I (Italian), and
S (Spanish).
NOTE
• The time zone options are PA (Pacific),
CE (Central), MO (Mountain), and EA (Eastern).
• Press MODE to toggle between Clock with
Seconds and Clock with Weekday display.
If no button is pressed, the alarm will
automatically silence after 2 minutes. It will then
sound again after 8 minutes.
main unit and stand
user’s guide
remote sensor
wire stand
Please read this user’s guide before
installing, setting up and using your new product.
Download from Www.Somanuals.com. All Manuals Search And Download.
|