Owner’s Manual
PRO-94 1000-Channel
Handheld Trunking Scanner
Please read before using this equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
Special Features ...................................................... 31
Delay .................................................................. 31
Turning Channel-Storage Banks On and Off ...... 31
Locking Out Channels ........................................ 32
Priority ................................................................ 32
Using the Keylock ............................................... 33
Using the Display Backlight ................................ 34
Using the Auto Backlight Display ........................ 34
Changing Search Speeds ................................... 34
Turning the Keytone Off/On ................................ 34
Turning the Battery Save Function Off/On .......... 35
Skipping Data Signals ........................................ 35
Receiving NWR-SAME and Weather Alert Signals .
35
Turning On the SAME Weather Alert Feature ..
36
SAME Signal Detection Updating ................ 36
NWR-SAME Alert Tone Test ........................ 37
NWR-SAME Code Detection Tests ............. 37
Trunking Operation .................................................. 38
Types of Trunking Systems ................................ 38
Setting the Scanner to the Trunking Mode ......... 39
Simultaneous Trunking ................................ 39
Setting Squelch for the Trunking Mode .............. 40
Storing Trunked Frequencies ............................. 40
Searching a Trunked Bank ................................. 42
Turning a Trunked Bank On or Off .............. 42
Skipping a Trunked Bank ............................ 43
Turning the Status Bit Ignore (S-Bit) On or Off .
43
Identifying a Trunked Frequency ................. 44
Selecting the EDACS Talk Group ID Format ....
44
EDACS Talk Group ID Range Search ......... 44
Using HOLD to Monitor an Active Talk Group ID
45
Temporarily Storing a Talk Group ID into the
Monitor ID Memory ...................................... 45
Locking Out Talk Group IDs ........................ 45
Unlocking a Single Talk Group ID ................ 46
Unlocking All Talk Group IDs ....................... 46
Using Trunk Scanning Scan Delay .............. 46
Monitoring Talk Group IDs ........................... 47
Channel Activity Bars ......................................... 47
Using Talk Group ID Lists ................................... 48
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Manually Storing Talk Group IDs in Talk Group
ID Lists ........................................................ 48
Entering EDACS Partial Talk Groups .......... 49
Moving Talk Group IDs to Talk Group ID Lists .
49
Scanning the Talk Group ID Lists ................ 50
Deleting a Stored Talk Group ID List ........... 50
Priority Talk Group ID Scanning .................. 50
Scanning Type I and Hybrid Trunked Systems .. 51
Selecting a Preset Fleet Map ...................... 54
Programming a Fleet Map .......................... 55
Programming the Base and Offset Frequencies
56
Programming a Hybrid System ................... 57
Turning On/Off the Motorola Disconnect Tone
Detect Function ........................................... 57
A General Guide to Scanning ................................. 58
Guide to Frequencies ......................................... 58
National Weather Frequencies ................... 58
Birdie Frequencies ...................................... 58
Guide to the Action Bands ................................. 59
Typical Band Usage .................................... 59
Primary Usage ............................................ 59
Band Allocation .................................................. 60
Frequency Conversion ....................................... 64
Troubleshooting ...................................................... 65
Resetting the Scanner ........................................ 68
Care and Maintenance ............................................ 69
Specifications .......................................................... 70
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ˆ Features
Your RadioShack 1000-Channel Handheld Trunking
Scanner is one of a new generation of scanners de-
®
signed to track Motorola Type I, Type II, hybrid ®analog
®
systems, (such as S®martnet and Privacy Plus ) plus
GE/Ericsson EDACS . Those systems are extensively
used in many 800 MHz, 900 MHz, and UHF communica-
tion systems.
Trunking communications systems let a large group of 2-
way radio users (or even different groups of 2-way radio
users) efficiently use a set of frequencies. Instead of se-
lecting a specific frequency for a transmission, the user
simply selects a talk group. The trunking system auto-
matically transmits the call on the first available frequen-
cy, and also sends (on a different frequency called a
data channel) a code that uniquely identifies that trans-
mission.
Since the trunking system might send a call and its re-
sponse on different frequencies, it is difficult to listen to
trunked communications using a regular scanner. The
scanner lets you select and monitor the data channel fre-
quency sent with a 2-way radio transmission, so you can
hear the call and response for that user and more easily
“follow” the conversation.
The scanner also lets you scan conventional transmis-
sions, and it is preprogrammed with service banks for
convenience. By pressing a single button, you can
quickly search those frequencies most commonly used
by public service and other agencies, without tedious
and complicated programming.
This scanner gives you direct access to over 37,000 ex-
citing frequencies, including police and fire departments,
ambulance services, and amateur radio services, and
you can change your selection at any time.
Your scanner also has these special features:
Triple-Conversion Circuitry — virtually eliminates any
interference from IF (intermediate frequency) images, so
you hear only the selected frequency.
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
5
20 Channel-Storage Banks — you can store up to 50
channels in each of 10 different banks, in two separate
groups, for a total of 1000 channels, so you can more
easily identify calls.
Five Scan Lists — you can store up to 50 trunking talk
group IDs in each trunk scanning bank.
Digital Weather Alert — uses the digital SAME (specific
area message encoding) signal transmitted with weather
alerts to identify the type of alert being issued.
Note: This scanner does not use the specific area fea-
ture of SAME. It responds to all alerts received.
Two-Second Scan Delay — delays scanning for about
2 seconds before moving to another channel, so you can
hear more replies that are made on the same channel.
Lock-Out Function — lets you set your scanner to skip
over specified channels or frequencies when scanning
or searching, and skip over talk group IDs when tracking
trunked systems.
Priority Channels — lets you program one channel in
each bank (20 in all) and then have the scanner check
that channel every 2 seconds while it scans the bank, so
you do not miss transmissions on those channels.
Five Service Banks — frequencies are preset in sepa-
rate police (fire/emergency), aircraft, ham, marine, and
weather banks, to make it easy to locate specific types of
calls.
Auto Backlight — automatically turns on the backlight
when the scanner receives signals.
Simultaneous Trunking Operation — allows the scan-
ner to trunk two trunking systems, Motorola and EDACS,
at the same time, as well as conventional systems.
Hypersearch — lets you set the scanner to search at
up to 300 steps per second in frequency bands with 5
kHz steps, compared to the normal search speed of 100
steps per second.
6
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
Hyperscan — the scanner automatically scans up to
50 channels per second to help you quickly find interest-
ing broadcasts.
Key Lock — lets you lock the scanner’s keys to help
prevent accidental changes to the scanner’s program-
ming.
Data Signal Skip — lets you set the scanner to skip
non-modulated or data signals (such as fax or modem
transmissions) during searches. This lets the scanner
avoid non-voice signals, making a search faster.
Disconnect Tone Detect — the scanner automatically
tunes to the trunking data channel when it receives a
disconnect transmission. You can turn this off, so you
can continuously monitor a channel with a weak trans-
mission where conversations are often disconnected.
Manual Access — lets you directly access any channel.
Liquid-Crystal Display — makes it easy to view and
change programming information.
Display Backlight — makes the scanner easy to read in
low-light situations.
Flexible Antenna with BNC Connector — provides ad-
equate reception in strong signal areas and is designed
to help prevent antenna breakage. Or, you can connect
an external antenna for better reception.
Monitor Memories — let you temporarily store up to 10
frequencies or talk group IDs.
Memory Backup — keeps the frequencies stored in
memory for an extended time if the scanner loses power.
Three Power Options — let you power the scanner us-
ing internal batteries, external AC power using an option-
al AC adapter/charger, or DC power using an optional
DC cigarette-lighter power cable.
Key Confirmation Tones — the scanner sounds a tone
when you perform an operation correctly, and an error
tone if you make an error.
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Battery Save — saves battery power when the scanner
does not detect any transmissions for more than 5 sec-
onds when a channel is manually selected.
Battery Low Alert — warns you when battery power
gets low.
Weather Alert Indicator — your scanner also functions
as a severe weather alert monitor.
Your scanner can receive these bands:
Frequency
Step
Range (MHz)
(kHz)
Transmission
29–29.7
29.7–50
5
5
10-m Ham Band
VHF Lo Band
50–54
5
6-m Ham Band
Aircraft Band
108–136.9750
137–144
144–148
148–174
216–224.9950
406–420
420–450
450–470
470–512
806–956
12.5
5
Military Land Mobile
2-m Ham Band
VHF Hi Band
5
5
5
1-m Ham Band
Federal Government
70-cm Ham Band
UHF Standard Band
UHF “T” Band
12.5
12.5
12.5
12.5
12.5
Public Service
“800” Band, except
cellular band
1240–1300
12.5
25-cm Ham Band
FCC NOTICE
Your scanner might cause radio or TV interference even
when it is operating properly. To determine whether your
scanner is causing the interference, turn off your scan-
ner. If the interference goes away, your scanner is caus-
ing it. Try the following methods to eliminate the
interference:
• move your scanner away from the receiver
• connect your scanner to an outlet that is on a differ-
ent electrical circuit from the receiver
8
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
• contact your local RadioShack store for help
Note: Mobile use of this scanner is unlawful or requires
a permit in some areas. Check the laws in your area.
SCANNING LEGALLY
Your scanner covers frequencies used by many different
groups including police and fire departments, ambulance
services, government agencies, private companies, am-
ateur radio services, military operations, pager services,
and wireline (telephone and telegraph) service provid-
ers. It is legal to listen to almost every transmission your
scanner can receive. However, there are some transmis-
sions you should never intentionally listen to. These in-
clude:
• telephone conversations (cellular, cordless, or other
private means of telephone signal transmission)
• pager transmissions
• any scrambled or encrypted transmissions
According to the Electronic Communications Privacy Act
(ECPA), as amended, you are subject to fines and possi-
ble imprisonment for intentionally listening to, using, or
divulging the contents of such a transmission unless you
have the consent of a party to the communication (un-
less such activity is otherwise illegal).
This scanner is designed to prevent reception of illegal
transmissions, in compliance with the law which requires
that scanners be manufactured in such a way as to not
be easily modifiable to pick up those transmissions. Do
not open your scanner’s case to make any modifications
that could allow it to pick up transmissions that it is not
legal to listen to. Doing so could subject you to legal pen-
alties.
We encourage responsible, legal scanner use.
Features
Download from Www.Somanuals.com. All Manuals Search And Download.
9
ˆ Preparation
You can power your scanner from any of three sources:
• internal batteries (not supplied)
• standard AC power (using an optional AC adapter)
• vehicle battery power (using an optional DC
adapter)
USING INTERNAL BATTERIES
You can power your scanner using four alkaline, lithium,
or rechargeable (Ni-Cd or Ni-MH) AA batteries (not sup-
plied). For the best performance and longest life, we rec-
ommend RadioShack batteries.
Using Non-Rechargeable Batteries
Follow these steps to install non-rechargeable batteries.
1. Turn VOLUME/OFF counterclockwise until it clicks to
make sure the power is turned off.
2. Slide up and hold the tab on the back of the scan-
ner, then pull up the battery compartment cover
from the top edge.
10
Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Before you install alkaline or any other non-
rechargeable batteries, use a pointed object such
as a ballpoint pen to set ALKALINE
JACK
NI-
CD inside the compartment to ALKALINE.
Warning: Set ALKALINE
JACK
NI-CD to NI-CD
for use only with nickel cadmium (Ni-Cd) or nickel
metal hydride (Ni-MH) rechargeable batteries.
Never attempt to recharge non-rechargeable batter-
ies. Non-rechargeable batteries can get hot or
explode if you try to recharge them.
4. Install two batteries in the compartment and two in
the cover as indicated by the polarity symbols (+
and –) marked inside those locations.
Cautions:
• Use only fresh batteries of the required size and
recommended type.
• Always remove old or weak batteries. Batteries
can leak chemicals that destroy electronic cir-
cuits.
• Do not mix old and new batteries, different types
of batteries (standard, alkaline, or rechargeable),
or rechargeable batteries of different capacities.
Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
11
5. Replace the cover, inserting the lower tabs first.
When BATT.Loflashes and the scanner beeps every
15 seconds, replace all four batteries.
Warning: Always dispose of old batteries promptly and
properly. Do not bury or burn them.
Using Rechargeable Batteries
You can also use four rechargeable batteries. Before
you use Ni-Cd or Ni-MH batteries, you must charge
them.
The scanner has a built-in circuit that lets you recharge
Ni-Cd and Ni-MH batteries while they are in the scanner.
To charge the batteries, set ALKALINE
JACK
NI-CD
to NI-CD, install the batteries in the scanner, and connect
an external AC or DC adapter to the scanner’s POWER
jack (see “Using AC Power” on Page 13 or “Using Vehi-
cle Battery Power” on Page 14).
Warning: Do not connect either adapter to the scanner if
non-rechargeable batteries (such as alkaline batteries)
are installed in the scanner and ALKALINE JACK NI-
CD is set to NI-CD, or if you are unsure of the switch’s po-
sition. Non-rechargeable batteries will get hot and can
even explode if you try to recharge them.
Before you use Ni-Cd or Ni-MH batteries for the first
time, charge them at least 24 hours to bring them to a
full charge.
Discharged batteries take about 10 to 18 hours to fully
recharge. If you use the scanner while the batteries are
charging, charging takes longer.
Notes:
• Ni-Cd batteries last longer and deliver more power if
you occasionally let them fully discharge. To do this,
simply use the scanner until it beeps every 15 sec-
onds and BATT.Loflashes.
• To prevent damage to Ni-Cd batteries, never charge
them in an area where the temperature is above
113°F (40°C) or below 40°F (4°C).
12
Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
Important: This scanner can use Ni-Cd
rechargeable batteries. At the end of a
Ni-Cd battery’s useful life, it must be re-
cycled or disposed of properly. Contact
your local, county, or state hazardous
waste management authorities for infor-
mation on recycling or disposal pro-
grams in your area or call 1-800-843-7422. Some
options that might be available are: municipal curbside
collection, drop-off boxes at retailers such as your local
RadioShack store, recycling collection centers, and mail-
back programs.
USING AC POWER
You can power the scanner using an 9V, 300 mA AC
adapter and a size H Adaptaplug™ adapter (neither sup-
plied). Both are available at your local RadioShack store.
Cautions:
You must use a Class 2 power source that
supplies 9V DC and delivers at least 300
mA. Its center tip must be set to negative
and its plug must fit the scanner’s POWER 9V 300MA
jack. Using an adapter that does not meet these
specifications could damage the scanner or the
adapter.
!
• Always connect the AC adapter to the scanner
before you connect it to AC power. When you finish,
disconnect the adapter from AC power before you
disconnect it from the scanner.
Follow these steps to use the scanner on AC power.
1. Turn VOLUME/OFF counterclockwise until it clicks to
make sure the power is turned off.
2. Insert the Adaptaplug into the AC adapter’s cord so
it reads TIP –. Insert the Adaptaplug into the scan-
ner’s POWER 9V 300MA jack.
3. Plug the AC adapter into a standard AC outlet.
If rechargeable batteries are installed and ALKALINE
JACK
NI-CD is set to NI-CD, the adapter powers the
Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
13
scanner and recharges the installed batteries at the
same time.
USING VEHICLE BATTERY POWER
You can power the scanner from a vehicle’s 12V power
source (such as cigarette-lighter socket) using a 9V, 300
mA DC adapter and a size H Adaptaplug (neither sup-
plied). Both are available at your local RadioShack store.
Cautions:
You must use a power source that sup-
plies 9V DC and delivers at least 300 mA.
Its center tip must be set to negative and
its plug must fit the scanner’s POWER 9V 300MA
jack. Using an adapter that does not meet these
specifications could damage the scanner or the
adapter.
!
• Always connect the DC adapter to the scanner
before you connect it to the power source. When
you finish, disconnect the adapter from the power
source before you disconnect it from the scanner.
• If batteries are installed, make sure the battery
switch inside the battery compartment is set to the
correct position (see “Using Internal Batteries” on
Page 10).
1. Turn VOLUME/OFF counterclockwise until it clicks to
make sure the power is turned off.
2. If the adapter has a voltage switch, set the switch to
9V.
3. Insert the Adaptaplug into the DC adapter’s cord so
it reads TIP –. Insert the Adaptaplug into the scan-
ner’s POWER 9V 300MA jack.
4. Plug the other end of the adapter into your vehicle’s
cigarette-lighter socket.
If rechargeable batteries are installed and ALKALINE
JACK
NI-CD is set to NI-CD, the adapter powers the
scanner and recharges the installed batteries at the
same time.
14
Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: If the scanner does not operate properly when
you use a DC adapter, unplug the adapter from the
cigarette-lighter socket and clean the socket to remove
ashes and debris.
CONNECTING THE ANTENNA
To attach the supplied
flexible antenna to the
connector on the top of
your scanner, align the
slots around the anten-
na’s connector with the
tabs on the scanner’s
BNC connector. Then
slide the antenna’s con-
nector down over the
scanner’s connector and
rotate the antenna con-
nector’s outer ring clockwise until it locks into place.
Connecting an Optional Antenna
The scanner’s BNC connector makes it easy to connect
a variety of optional antennas, including an external mo-
bile antenna or outdoor base station antenna. Your local
RadioShack store sells a wide selection of antennas.
Note: Always use 50-ohm, RG-58, or RG-8, coaxial ca-
ble to connect an outdoor antenna. If the antenna is over
50 feet from the scanner, use RG-8 low-loss dielectric
coaxial cable. If your antenna’s cable does not have a
BNC connector, your local RadioShack store carries a
variety of BNC adapters.
CONNECTING AN EARPHONE/
HEADPHONE
For private listening, you can plug an optional earphone
or mono headphones into the
jack on top of your
Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
15
scanner. This automatically disconnects the internal
speaker.
Listening Safely
To protect your hearing, follow these guidelines when
you use an earphone or headphones.
• Do not listen at extremely high volume levels.
Extended high-volume listening can lead to perma-
nent hearing loss.
• Set the volume to the lowest setting before you
begin listening. After you begin listening, adjust the
volume to a comfortable level.
• Once you set the volume, do not increase it. Over
time, your ears adapt to the volume level, so a vol-
ume level that does not cause discomfort might still
damage your hearing.
Traffic Safety
Do not use an earphone or headphones with your scan-
ner when operating a motor vehicle in or near traffic. Do-
ing so can create a traffic hazard and could be illegal in
some areas.
If you use an earphone or headphones with your scan-
ner, be very careful. Do not listen to a continuous broad-
cast. Even though some earphones/headphones let you
hear some outside sounds when listening at normal vol-
ume levels, they still can present a traffic hazard.
16
Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING AN EXTENSION
SPEAKER
In a noisy area, an optional extension speaker, posi-
tioned in the right place, might provide more comfort-
1
8
able listening. Plug the speaker cable’s / -inch (3.5-
mm) mini-plug into your scanner’s jack. Your local Ra-
dioShack store carries a selection of suitable speakers.
ATTACHING THE BELT CLIP
To make your scanner easi-
er to carry when you are on
the go, use the supplied
belt clip. Use a Phillips
screwdriver and the sup-
plied screws to attach the
clip to the scanner.
Preparation
Download from Www.Somanuals.com. All Manuals Search And Download.
17
ˆ About Your Scanner
We use a few simple terms in this manual to explain the
features of the scanner. Familiarize yourself with these
terms and the scanner’s features, and you can put the
scanner to work for you right away. Simply determine the
type of communications you want to receive, then set the
scanner to scan those communications.
The scanner scans conventional frequencies and trunk-
ed systems. For more information about trunked trans-
missions see “Trunking Operation” on Page 38.
A frequency, expressed in kHz or MHz, is the tuning lo-
cation of a station. To find active frequencies, you use
the search function or refer to a frequency reference
such as the included Trunking Frequency Guide.
Besides searching within a selected frequency range,
you can also search your scanner’s service banks. Ser-
vice banks are preset groups of frequencies categorized
by the type of services that use those frequencies. For
example, many amateur radio frequencies are located in
the HAM service bank.
When you search and find a desired frequency, you can
store it into a programmable memory location called a
channel. Channels are grouped into channel-storage
banks. The scanner has 500 channels in channel-
storage bank A and another 500 in channel-storage
bank B. Each bank of 500 is divided into ten 50-channel
sets. You can scan the channel-storage banks to see if
there is activity on the frequencies stored there.
Or, when you find a frequency, you can store it into a
temporary memory location called a monitor memory
until you decide whether or not to move it to a channel.
Just keep in mind — you search frequencies and scan
channels.
18
About Your Scanner
Download from Www.Somanuals.com. All Manuals Search And Download.
A LOOK AT THE KEYPAD
Key
Function(s)
HOLD (A/B)
Switches the bank groups; holds the fre-
quency search; holds the current ID in the
trunking mode.
SCAN
MAN
Scans the stored channels and scan lists.
Stops scanning and lets you directly enter a
channel number or frequency; manually
stores talk group IDs in scan lists.
PROG
Stores frequencies into channels; programs
the trunking frequency, fleet map, and ID
memories.
TRUNK
Turns trunk tracking on and off and stores
trunked frequencies.
SRC (LIMIT) Starts a limit search; searches a specified
frequency range for frequencies; searches
for another active ID during trunking opera-
tion.
ALT (DATA)
Turns on or off the data signal skip feature;
moves through menu settings while trunking;
turns on or off the NWR-SAME weather alert.
H/S
(PRIORITY)
Sets and turns on and off the priority and pri-
ority scanning feature; turns on and off
Hypersearch.
S/S (L-OUT) Lets you lock out selected channels or skip
specified frequencies during a search; lets
you lock out a selected ID while trunking.
Locks the keypad to prevent accidental pro-
(KEYLOCK)
gram changes; turns the display backlight on
and off.
About Your Scanner
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Key
Function(s)
DELAY
Programs a 2-second delay for the selected
channel, a limit search, or each service scan;
programs a 5-second delay while trunking.
Searches down through a selected frequency
range; selects options during programming;
changes the ID location number while trunk-
ing.
9
8
Searches up through a selected frequency
range; selects options during programming;
changes the ID location number while trunk-
ing.
Number
Keys
Each key has a single-digit label and a range
of numbers. Single-digit keys enter a chan-
nel, a frequency, or an ID number. The range
of numbers (51–100, for example) is used to
enter the channels of a memory bank.
• (MON/CLR) Stores frequencies into monitor memories
during a search; recalls frequencies from the
monitor memories when programming
a
channel; stores IDs into the monitor memo-
ries or selects options while trunking; enters
a decimal point or clears an incorrect entry.
E (SVC)
Starts a service bank search; enters frequen-
cies into channels; stores the talk group IDs
in the scan lists.
A LOOK AT THE DISPLAY
The display has indicators that show the scanner’s cur-
rent operating status. The display information helps you
understand how your scanner operates.
Bank Aor B— appears with numbers (1–10). Aor B
indicates the bank group. The numbers show which
channel-storage banks are turned on for scanning.
TRUNK— appears when you select the trunking opera-
tion and while you store a trunking frequency into a
channel.
P
— appears when you select a priority channel.
20
About Your Scanner
Download from Www.Somanuals.com. All Manuals Search And Download.
DATA— appears when the data skip function is active;
appears when the disconnect tone detect function is off
in the trunking mode.
SCAN— appears when you scan channels.
LIST — appears with numbers (1–5) during trunking.
Numbers with a bar under them show which ID scan list
banks are turned on for scanning.
SEARCH— appears during limit, direct, service, and ID
searches, and blinks when you monitor IDs.
PRI— appears when the priority feature is turned on.
HOLD — appears during limit, direct, service, and ID
searches, and ID monitor holds; flashes while the scan-
ner is temporarily monitoring a programmed ID.
DLY— appears when you select a delay.
L/O — appears when you manually select a channel
you locked out.
K/L(keylock) — appears when you lock the keypad.
Error— appears when you make an entry error.
BATTLo— alerts you when the battery power gets low.
MON — appears during search modes, ID search moni-
tor, program ID monitor, or when you select a monitor
memory. The number to the right of this indicator shows
the current monitor memory.
MAN— appears when you press MAN to directly enter a
channel number or frequency.
PGM— appears while you store a frequency into a chan-
nel, while you enter a frequency range during a limit
search, or when you program trunking frequencies, fleet
maps, or ID memories while trunking.
HYPER — appears while Hyperscan or Hypersearch is
active during a direct or limit search.
8 or 9 — appears during a limit, direct, or service
search, indicating the search direction.
About Your Scanner
Download from Www.Somanuals.com. All Manuals Search And Download.
21
S
— appears when the battery save function is active
(during conventional scanning only).
WXHAMMRNAIRPOL— appears along with an indica-
tor which shows the current service bank during a ser-
vice search.
ALERT— appears when the weather alert is turned on,
or flashes when the scanner detects an alert coded sig-
nal.
Mor E— indicate either a Motorola (M) trunking system
or EDACS (E) system.
CH — appears with a number to its left to indicate to
which channel the scanner is tuned to.
UNDERSTANDING BANKS
Service Banks
The scanner is preprogrammed with all the frequencies
allocated to the weather, ham, marine, aircraft, and po-
lice (fire/emergency) services. This helps you quickly
find active frequencies instead of doing a limit search
(see “Service Bank Search” on Page 27).
Channel Storage Banks
To make it easier to identify and select the channels you
want to listen to, all the channels are divided into main
bank Groups A and B. Each main bank group has 10
banks of 50 channels. Use each channel-storage bank
to group frequencies, such as those for the police de-
partment, fire department, ambulance services, or air-
craft (see “Guide to the Action Bands” on Page 59).
For example, the police department might use four fre-
quencies in your town while the fire department uses an
additional four. You could program the four police fre-
quencies starting with Channel 1 (the first channel in
bank 1), and program the fire department frequencies
starting with Channel 51 (the first channel in bank 2).
22
About Your Scanner
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitor Memories
The scanner also has 10 temporary memory locations
called monitor memories. Use these monitor memories
to temporarily store frequencies when you search
through an entire band (see “Searching For and Tempo-
rarily Storing Active Frequencies” on Page 25). You can
then move a frequency to a channel for permanent stor-
age. See “Moving a Frequency From a Monitor Memory
to a Channel” on Page 29.
While you are searching frequencies, the 10 numbers at
the top of the display indicate the 10 monitor memories.
MONappears and the flashing number beside it indicates
the currently active monitor memory.
About Your Scanner
Download from Www.Somanuals.com. All Manuals Search And Download.
23
ˆ Operation
TURNING ON THE SCANNER
AND SETTING SQUELCH
Note: Make sure the scanner’s antenna is connected
before you turn it on.
1. Turn SQUELCH fully counterclockwise.
VOLUME
SQUELCH
2. Turn VOLUME/OFF clockwise until it clicks and you
hear a hissing sound.
3. If the scanner is scanning, press MAN (manual) to
stop scanning, then turn SQUELCH clockwise until
the hissing stops.
STORING KNOWN FREQUENCIES
INTO CHANNELS
You can locate and store specific frequencies into chan-
nels for later use. To assist you in locating a desired fre-
quency from the scanner’s wide range, consider using a
frequency guide. Good references for active frequencies
are the RadioShack Police Call Guide including Fire and
Emergency Services, and Official Aeronautical Frequen-
cy Directory. We update these directories every year, so
be sure to get a current copy.
Note: To store trunked system frequencies, see “Storing
Trunked Frequencies” on Page 40.
Follow these steps to store frequencies into channels.
1. Press MAN and hold down A/B (HOLD) for about 2
seconds to select either main bank group. Enter the
channel number where you want to store a fre-
24
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
quency, then press PROG. The channel number
appears.
2. Use the number keys and • (MON/CLR) to enter the
frequency (including the decimal point) you want to
store.
3. Press E (SVC) to store the frequency into the chan-
nel.
Notes:
• If you entered an invalid frequency in Step 2,
Error appears and the scanner beeps three
times. Enter a valid frequency.
• The scanner automatically rounds the entered
number to the nearest valid frequency. For exam-
ple, if you enter 151.473 (MHz), your scanner
accepts it as 151.475.
Press DELAY to pause scanning 2 seconds after the
end of a transmission before scanning proceeds to
the next channel (see “Delay” on Page 31). The
scanner stores this setting in the channel.
4. To program the next channel in sequence, press
PROG and repeat Steps 2 and 3.
SEARCHING FOR AND TEMPORARILY
STORING ACTIVE FREQUENCIES
If you do not have a reference to frequencies in your ar-
ea, use a limit, direct, or service search (except weather
service search) to find a transmission. Also see “Guide
to the Action Bands” on Page 59.
Note: While doing a limit, direct, or service bank search,
press:
• DELAY if you want the scanner to pause 2 seconds
after a transmission ends before it proceeds to the
next frequency (see “Delay” on Page 31).
• DATA if you want the scanner to skip data signals
(such as fax or modem signals) and search only for
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
25
audio (voice) signals (see “Skipping Data Signals”
on Page 35).
Limit Search
A limit search lets you search within a specific range
of frequencies. -L-appears during a limit search.
1. Press PROG, then LIMIT (SRC). Lo and 29.000
MHz (or the previous low limit frequency) appear.
29.000 MHz is the low end of the scanner’s range.
2. Enter the frequency that is the lower limit of the
range you want to search (including the decimal
point), then press E.
3. Press LIMIT. Hiand 1300.000MHz(or the previ-
ous high limit frequency) appear. 1300.000 MHz is
the upper limit of the scanner’s range.
4. Enter the frequency that is the upper limit of the
range you want to search (including the decimal
point), then press E (SVC) again.
5. Press 9 to search from the upper to the lower limit,
or 8#to search from the lower to the upper limit.
6. When the scanner stops on a transmission, quickly
press either:
HOLD (A/B) to stop searching to listen to the trans-
mission. HOLDappears.
MON/CLR (•) to store the displayed frequency into
the current monitor memory.
7. To release the hold and continue searching, press
HOLD (A/B) or hold down 9 or 8 for at least 1 sec-
ond. Or, if you did not press MON/CLR (•), simply
press 8 or 9 to continue searching.
Direct Search
You can search up or down from the currently displayed
frequency using direct search. -d- appears during
searching until the scanner stops.
26
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Press MAN.
2. Enter the frequency you want to start from using the
number keys. (Press to enter a decimal point).
•
Notes:
• To start the search from a frequency already
stored in one of your scanner’s channels, press
MAN or PROG. Then use the number keys to
enter the channel number and then press MAN or
PROG again.
• If you enter an invalid frequency, the scanner dis-
plays Error.Press MON/CLR (•).
3. Press 9 to search down or 8 to search up from
the selected frequency. -d-, SEARCH, and 8 or
9 appear.
4. When the scanner stops on a transmission, quickly
press either:
HOLD to stop searching and listen to the transmis-
sion. HOLDappears.
MON/CLR to store the displayed frequency into the
current monitor memory.
5. To release the hold and continue searching, press
HOLD or hold down 8 or 9 for at least 1 second.
Or, if you did not press HOLD, simply press 8 or
9 to continue searching.
Note: To step through the frequencies while HOLD
appears, press 8 or 9.
Service Bank Search
You can search for weather, ham, marine, aircraft, or po-
lice (fire/emergency) transmissions without knowing the
specific frequencies used in your area. The scanner is
preprogrammed with all the frequencies allocated to
these services. To use this feature, press SVC(E).
SEARCH appears and the scanner searches starting
with the weather service bank. To select a different ser-
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
27
vice bank, repeatedly press SVC. A bar appears above
the selected bank.
When the scanner stops on a transmission, quickly
press either:
• HOLD to stop searching and listen to the transmis-
sion. HOLDappears.
• MON/CLR to store the displayed frequency into the
current monitor memory.
To release the hold and continue searching, press HOLD
(A/B) or hold down 8 or 9 for at least 1 second. Or, if
you did not press HOLD (A/B), simply press 8 or 9 to
continue searching.
Note: Because there are many different frequencies al-
located to fire and police departments, it can take sever-
al minutes to search all the service frequencies.
Search Skip Memory
You can skip up to 50 specified frequencies during a limit
or direct search and up to 20 specified frequencies dur-
ing a service bank search. This lets you avoid unwanted
frequencies or those already stored in a channel.
Note: You cannot skip frequencies during WX service
search.
To skip a frequency, press S/S (L-OUT) when the scanner
stops on the frequency during a limit, direct, or service
search. The scanner stores the frequency in memory
and automatically resumes the search.
To clear a single frequency from skip memory so the
scanner stops on it during a limit, direct, or service bank
search:
1. Press HOLD to stop the search.
2. Press 8 or 9 to select the frequency. L/O
appears.
3. Press S/S. L/Odisappears.
28
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
To clear all the skip frequencies at once while searching,
press HOLD, then hold down S/S until the scanner beeps
twice.
Notes:
• If you selected all frequencies to be skipped within
the search range, the scanner beeps 3 times and
does not search.
• If you select more than 50 frequencies to skip, each
new frequency replaces a frequency previously
stored, beginning with the first stored frequency.
• Press 8 or 9 to select a skipped frequency while
HOLD appears. L/O appears when you select a
skipped frequency.
LISTENING TO THE MONITOR
MEMORIES
Note: To listen to the monitor memories, the priority
channel feature must be turned off (see “Priority” on
Page 32).
To listen to the frequency stored in any one of the ten
monitor memories, press MAN, MON/CLR (•), then the
–
number of the desired monitor memory (0 9), or repeat-
edly press MON/CLR (•) to step through the monitor mem-
ories.
MOVING A FREQUENCY FROM A
MONITOR MEMORY TO A CHANNEL
1. Press MAN. MANappears.
2. Enter the number of the desired target channel
where you want to move the frequency that is stored
in the monitor memory, then press PROG. PGM
appears.
3. Press MON/CLR (•) then enter the number (0–9) of
the monitor memory containing the frequency.
4. Press E. The frequency transfers from the monitor
memory into the selected channel.
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
29
5. Repeat Steps 2–4 to store the remaining monitor
memory frequencies into channels, as necessary.
SCANNING THE STORED CHANNELS
To begin scanning channels, press SCAN. The scanner
scans through all non-locked channels in the activated
banks. (See “Locking Out Channels” on Page 32 and
“Turning Channel-Storage Banks On and Off” on
Page 31). When the scanner finds a transmission, it
stops on it. When the transmission ends, the scanner re-
sumes scanning.
Notes:
• If you have not stored frequencies into any chan-
nels, the scanner does not scan.
• If the scanner picks up unwanted partial, or very
weak transmissions, turn SQUELCH clockwise to
decrease the scanner’s sensitivity to these signals.
To listen to a weak or distant station, turn SQUELCH
counterclockwise.
• To ensure proper scanning, adjust SQUELCH until
the audio mutes.
• To scan in the trunk scanning mode, see “Trunking
Operation” on Page 38.
MANUALLY SELECTING A CHANNEL
You can continuously monitor a single channel without
scanning. This is useful if you hear an emergency broad-
cast on a channel and do not want to miss any details —
even though there might be periods of silence — or if
you want to monitor a specific channel.
To manually select a channel, press MAN, enter the
channel number then press MAN again.
Or, during scanning, if the radio stops at a channel you
want to listen to, press MAN one time. (Repeatedly
pressing MAN at this time causes the scanner to step
through the channels.) Press SCAN to resume automatic
scanning.
30
Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
ˆ Special Features
DELAY
Sometimes a user might pause before replying to a
transmission. To avoid missing a reply on a specific
channel, you can program a 2-second delay into any
channel or frequency. The scanner continues to monitor
the channel frequency for an additional 2 seconds after
the transmission stops before resuming scanning or
searching.
Depending on how the scanner is operating, follow one
of these steps to program a delay.
• If the scanner is scanning and stops on an active
channel where you want to store a delay, quickly
press DELAY before it continues scanning again.
DLYappears.
• If the desired channel is not selected, manually
select the channel, then press DELAY. DLYappears.
• If the scanner is searching, press DELAY while the
scanner is searching. DLYappears and the scan-
ner automatically adds a 2-second delay to every
frequency it stops on in that band.
To turn off the 2-second delay, press DELAY while the
scanner is monitoring a channel, scanning, or searching.
DLYdisappears.
TURNING CHANNEL-STORAGE
BANKS ON AND OFF
You can turn each channel-storage bank on and off.
When you turn off a bank, the scanner does not scan
any of the 50 channels in that bank.
While scanning, press the number key that corresponds
to the bank you want to turn on or off. Numbers appear
at the top of the display, showing the currently selected
banks.
Special Features
Download from Www.Somanuals.com. All Manuals Search And Download.
31
The scanner scans all the channels within the displayed
banks that are not locked out (see “Locking Out Chan-
nels”). The bank number flashes when the scanner
scans a channel that belongs to the bank.
Notes:
• You can manually select any channel within a bank,
even if that bank is turned off.
• You cannot turn off all banks. One bank must
always be active.
LOCKING OUT CHANNELS
You can increase the scanning speed by locking out
channels that have a continuous transmission, such as a
weather channel. To lock out a channel, manually se-
lect the channel, then press L-OUT(S/S). L/O ap-
pears.
Note: You can still manually select locked-out channels.
To remove the lockout from a channel, manually select
the channel, then press L-OUT(S/S). L/Odisappears.
To unlock all channels in the banks that are turned on,
press MAN to stop scanning, then hold down L-OUT(S/S)
until the scanner beeps twice.
PRIORITY
The priority feature lets you scan through the channels
and still not miss important or interesting calls on specific
channels. You can program one stored channel in each
bank as a priority channel (10 for the banks in Group A
and 10 for the banks in Group B). If the priority feature is
turned on, as the scanner scans the bank, it checks that
bank’s priority channel for activity every 2 seconds.
The scanner automatically designates each bank’s first
channel as its priority channel. Follow these steps to se-
lect a different channel in a bank as the priority channel.
1. Press PROG.
32
Special Features
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Enter the channel number you want to select as the
priority channel, then press PRIORITY (H/S). P
appears to the right of the selected channel number.
3. Repeat Steps 1 and 2 for the channel in each bank
you want to program as a priority channel.
To review all priority channels (in ascending order only),
press PROG, then repeatedly press PRIORITY to see the
numbers of the priority channels.
To turn on the priority feature, press PRIORITY during
scanning. PRI appears. Then the scanner checks the
designated priority channel every 2 seconds in each
bank. The bank number appears at the top of the dis-
play.
To turn off the priority feature, press PRIORITY. PRIdis-
appears.
Notes:
• The priority feature must be turned off to listen to the
monitor memories or to use the data skip feature.
• If you have locked out all priority channels,
LOCOUt appears when you activate the priority
feature. To unlock any desired priority channels, see
“Locking Out Channels” on Page 32.
USING THE KEYLOCK
To protect the scanner from accidental program chang-
es, turn on the keylock feature. When the scanner is
locked, the only controls that operate are SCAN, MAN,
KEYLOCK, VOLUME/OFF, and SQUELCH.
To turn on the keylock, hold down KEYLOCK until K/L
appears. To turn it off, hold down KEYLOCK until K/L
disappears.
Note: Using keylock does not prevent the scanner from
scanning channels.
Special Features
Download from Www.Somanuals.com. All Manuals Search And Download.
33
USING THE DISPLAY BACKLIGHT
To turn on the display light for easy viewing at night,
press
.The display lights for 15 seconds. To turn off
again.
the light sooner, press
USING THE AUTO BACKLIGHT
DISPLAY
You can set the scanner so the auto backlight turns on
for about 5 seconds when the scanner receives signals.
If you press a key (except
) within 5 seconds, the
display remains lighted for more than 15 seconds.
To turn auto backlight display on or off, turn off the scan-
ner. Then hold down
and turn on the scanner. on
AutLitbriefly appears when auto backlight is on. OFF
AutLitbriefly appears when auto backlight is off.
CHANGING SEARCH SPEEDS
Note: Hypersearch applies only to the 5 kHz step bands
(29–54 MHz, 137–174 MHz, and 216–224.9950 MHz).
The scanner has two search speeds.
Normal Search
Hypersearch
100 steps/second
300 steps/second
To switch between the normal and Hypersearch speeds
during limit search or direct search, press H/S. HYPER
appears during Hypersearch.
TURNING THE KEYTONE OFF/ON
1. Turn off the scanner.
2. While holding down L-OUT/S/S, turn on the scanner.
OFFbEEPappears.
To turn the key tone back on, repeat these steps. on
bEEPappears.
34
Special Features
Download from Www.Somanuals.com. All Manuals Search And Download.
TURNING THE BATTERY SAVE
FUNCTION OFF/ON
When the scanner is set to receive (monitor) a manually
selected channel, and it is not actively scanning, using
the battery save feature conserves energy.
To turn the battery save function off or back on, turn off
the scanner, then hold down PRIORITY and turn on the
scanner.
• OFF SAVE briefly appears when battery save has
been turned off.
• on SAVE briefly appears when battery save has
been turned on, and S appears.
When the battery save feature is active, the scanner re-
peatedly turns off the internal power for 1 second, then
1
2
turns it back on for about / second to check for a trans-
mission.
SKIPPING DATA SIGNALS
To prevent the scanner from stopping on channels that
consist of nonmodulated or data signals (such as fax or
modem transmissions) during a search or scan, turn on
the data skip feature. When the radio receives a data
signal and data skip is selected, the signal is ignored.
To turn on the data skip feature, turn off the priority fea-
ture if it is on (see “Priority” on Page 32), then press DA-
TA. DATA appears. To turn off the data skip feature,
press DATA again. DATA disappears.
Note: This feature does not apply to the air service band
as data signals are not generally found in this service.
RECEIVING NWR-SAME AND
WEATHER ALERT SIGNALS
In 1994, the National Oceanic and Aerospace Adminis-
tration (NOAA) began broadcasting alerts that include
digitally encoded data. Specific Area Message Encoding
(SAME) includes information which identifies the severity
of the alert. While this scanner does not encode specific
Special Features
Download from Www.Somanuals.com. All Manuals Search And Download.
35
geographical data, it does detect SAME signals and de-
code the alert level. The scanner displays this data as
codes corresponding to the levels of severity (L1, L2,
and L3).
Turning On the SAME Weather
Alert Feature
1. Press SVC (E) and select the weather search mode.
See “Service Bank Search” on Page 27.
2. Press ALT (DATA). ALERTappears. This mutes the
audio until the scanner receives a SAME-coded sig-
nal.
When the scanner receives a SAME-coded signal,
ALERTflashes and an associated “L” code (which indi-
cates the severity of the alert) appears, as well. The
scanner remains on the weather channel and the audio
turns on so you can hear the weather broadcast.
The scanner displays one of the following codes to indi-
cate the alert level.
L1: Warning
L2: Watch
L3: Statement
-----: Non-emergency
In addition to weather alerts, the scanner also receives
test and other event information. See “NWR-SAME
Code Detection Tests” on Page 37.
SAME Signal Detection Updating
When the scanner receives a SAME-coded signal, it re-
tains information about the most recent alert until you
turn off the power. Once the scanner detects an alert
code, ALERT flashes. To verify the specific alert level
(L1, L2, or L3) press SVC (E) to select the weather
search mode. Press ALT (DATA) to clear the alert.
36
Special Features
Download from Www.Somanuals.com. All Manuals Search And Download.
NWR-SAME Alert Tone Test
To hear and test the tones for the three alert levels,
press SVC (E) to select the weather service, then hold
down ALT for about 1 second. The tones sound in the or-
der L3, L2, then L1, and TEStflashes. Each alert code
appears as its tone sounds. Press any key to end the
test sequence.
NWR-SAME Code Detection Tests
The National Weather Service sends out daily, weekly,
and monthly test (and sometimes demonstration) sig-
nals, which let anyone with a receiver (such as the scan-
ner) verify that the equipment is working properly.
To find out the specific test schedule in your area, con-
tact your local NOAA or NWS office. Those offices are
usually listed in the telephone book under US Govern-
ment, Department of Commerce.
When ALERTappears, hold down ALT (DATA) for about
1 second. The frequency and TEStappear alternately.
When the scanner receives the test code, TEStalso ap-
pears.
To exit the test mode, press ALT (DATA) for about 1 sec-
ond.
Note: If an actual alert is sent, the scanner sounds the
appropriate tone and displays the corresponding alert
level.
Special Features
Download from Www.Somanuals.com. All Manuals Search And Download.
37
ˆ Trunking Operation
The scanner tracks transmissions that use the Motorola
Type I, Type II, hybrid, and Ericsson EDACS analog
trunking systems. The frequencies for many of the 800
MHz, 900 MHz, and EDACS public safety systems are
listed in the separate National Public Safety Trunked
System Frequency Guide included with your scanner.
TYPES OF TRUNKING SYSTEMS
This trunking scanner monitors two basic types of sys-
tems — the Motorola Type I/Type II or hybrid system,
and the Ericsson EDACS system. Instead of selecting a
specific frequency to transmit on, a trunked system
chooses one of several frequencies in a 2-way radio us-
er’s talk group when that user presses their PTT (push to
talk) control. Thus, trunking systems, in general, allocate
a few frequencies among many different users. Motorola
Type I and Type II systems achieve the same results in a
slightly different way. One important distinction between
these systems is the amount of data transmitted by each
radio when the operator pushes the PTT control. A Type I
system transmits the radio’s ID and its current affiliation
or the trunk system to which it belongs. A Type II system
only transmits the radio’s ID.
Why the difference? In Type I systems, each radio in the
trunk group individually transmits its own affiliation, while
the trunk system maintains a database that determines
each radio’s affiliation(s) in Type II systems.
Another difference between the systems is that Type I
systems are arranged in a fleet-subfleet hierarchy. For
example, it is possible for a city using a Type I system to
designate four fleets, each with eight subfleets.
The police department, fire department, utilities group,
and city administration could each be a separate fleet.
The police might decide to further divide its fleet into
subfleets, such as dispatch, tactical operations, detec-
tives, north, south, east, and west side patrols, and su-
pervisors. All the available police radios would then be
assigned to one of the police subfleets, letting the police
38
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
centralize their communications and control the type of
users on a single system. Determining the exact fleet-
subfleet hierarchy for a particular area is referred to as
fleet map programming.
The disadvantage of a Type I system is that the brief
burst of data sent when a user transmits must contain
the radio’s ID, its fleet information, and the subfleet infor-
mation as well. This is three times the amount of data a
Type II system radio sends. Since the data capacity of
Type I systems is limited and the total amount of data in-
creases with each user, Type I systems usually accom-
modate fewer users than Type II systems. Nevertheless,
Type I systems are still in use.
There are also hybrid systems which are a combination
of Type I and Type II. Your scanner is preset to monitor
Type II systems, but you can change to Type I or a hy-
brid of Type I and Type II systems by selecting a prepro-
grammed fleet map or creating a custom fleet map for
your area (see “Scanning Type I and Hybrid Trunked
Systems” on Page 51).
SETTING THE SCANNER TO THE
TRUNKING MODE
Simultaneous Trunking
The scanner allows you to track up to 10 systems at a
time. You can trunk scan or search and scan conven-
tional frequencies at the same time. You can also pro-
gram conventional frequencies in the same bank as
trunking systems.
After the scanner is finished checking activity in the
trunked system, it scans other conventional frequencies
in the bank. (Only trunking frequencies are programmed
in trunk mode.)
If a system is inactive for 1 second and there are no con-
ventional channels in the bank, the scanner starts scan-
ning the next selected trunk bank. If you turned DELAY
on, the scanner starts scanning the next trunk bank after
about 5 seconds.
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
39
To scan both trunking and conventional banks, select
the banks you wish to be active with trunking off, then
press TRUNK. The scanner begins scanning. To return
to conventional scanning, press TRUNK again.
SETTING SQUELCH FOR THE
TRUNKING MODE
Your scanner’s squelch setting is automatically adjusted
during trunking, which means it is not necessary to man-
ually adjust squelch while scanning trunked transmis-
sions. However, the squelch setting can affect how fast
your scanner acquires the data channel, and, in some in-
stances, can prevent your scanner from acquiring the
data channel at all.
We recommend you set SQUELCH fully clockwise before
selecting a trunked bank.
Note: Change this setting as needed for the best perfor-
mance in your area.
STORING TRUNKED FREQUENCIES
Follow these steps to select, program, and store trunked
frequencies.
1. Press PROG then TRUNK. TRUNKappears and one
or more bank numbers flash.
2. Press the number key (1–10) of the desired target
storage bank. Select one of the trunk systems by
repeatedly pressing 8 or 9 to select a trunking
system type, then press E (SVC). The scanner then
automatically selects the first channel in the
selected bank.
Note: You can select from the following six systems:
You See
E1
Trunk System
Motorola Type I, 800 MHz frequencies
EDACS frequencies
Ed
E2– 800
Motorola Type II, 800 MHz frequencies
40
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
You See
Trunk System
E2– 900
E2– Hi
Motorola Type II, 900 MHz frequencies
Motorola Type II, VHF frequencies
Motorola Type II, UHF frequencies
E2– UHF
3. Use the number keys to enter a valid frequency
within the trunk system, then press E (SVC). BANK
and the bank number, the channel number, and E
(EDACS) or M(Motorola) appears depending upon
the trunk system selected.
Notes:
• If you enter an invalid frequency (outside the
selected range), the scanner beeps, the channel
number flashes and Errorappears. If this hap-
pens, press MON/CLR ( ) to clear the frequency,
•
then repeat the entry.
• For EDACS systems, you must enter the fre-
quencies in logical channel number (LCN) order.
• If you try to enter a duplicate frequency in a bank,
the scanner beeps and the channel which was
previously stored appears.
• It is very important that you enter all the listed fre-
quencies for the selected agency in Step 3. Oth-
erwise, trunking will not occur when you press
SRC in Step 6.
4. Press either PROG or 8 to select the next channel
in the bank.
5. Repeat Steps 3 and 4 until you enter all desired fre-
quencies in that bank.
6. Press SCAN, then SRC to begin searching for the
trunk’s data channel and scan conventional fre-
quencies at the same time.
As the scanner looks through the frequencies, you
see them on the display. When the scanner finds
the controlling data channel, the scanner begins
trunking.
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
41
SEARCHING A TRUNKED BANK
Once the data channel is acquired, the scanner begins a
trunk search. With the search function, you will be able
to find all the active talk groups within the trunked sys-
tem. Press SCAN. You can switch to the trunk scan
mode from the trunk search mode. See “Scanning the
Talk Group ID Lists” on Page 50.
While scanning conventional frequencies, follow the
steps below to switch to the trunk mode after the scan-
ner finds the data channel.
1. Press TRUNK. The scanner begins scanning both
trunking and conventional banks.
2. Hold down SCAN for about 1 second. The scanner
switches to the trunk scan mode.
3. Hold down SRC for about 1 second. The scanner
switches to the trunk search mode.
Hint: While searching, you may not know exactly to
whom the talk group IDs are assigned until you listen
awhile. To locate talk group ID lists for your local police,
fire, and other agencies, refer to frequency guides avail-
able at your local RadioShack store or on internet sites
mine the type of agency you are listening to after a short
while, be it a police, fire, or emergency medical 2-way ra-
dio user. Once you have identified the type of service,
note the associated talk group ID of that unit for future
programming. See “Identifying a Trunked Frequency” on
Page 44. Determining the service associated with a talk
group ID might take awhile, but discovering the ID owner
of each signal is half the fun of trunk scanning!
Turning a Trunked Bank On or Off
Press DATA (ALT) during trunk scanning. The selected
trunked banks appear. Press the bank number (0–9), to
turn the desired bank on or off.
42
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Skipping a Trunked Bank
You can scan conventional frequencies programmed in
the same bank by holding down SRC (LIMIT) for about 2
seconds. If there is no conventional frequency, the scan-
ner scans the next bank.
Turning the Status Bit Ignore (S-Bit)
On or Off
You can set how your scanner works with status bits
(also called S-Bits), letting you control how the scanner
interprets and displays talk group IDs.
The last four bits of a Motorola Type II talk group ID (a
binary 16-bit code) are the status bits. In some systems,
status bits identify special situations (such as an emer-
gency status).
Your scanner is preset to assume that the status bits in a
talk group ID are set to 0 and ignores them. For exam-
ple, when the scanner receives the talk group ID
010111001110 0011, it reads the ID as 010111001110
0000 and converts the first 12 bits of the ID to 23776 (the
talk group ID). However, since the status bit value is 3
(0011 converted to decimal equals 3), the ID is actually
23779.
If you are scanning a Motorola Type I system and do not
have a fleet map for that system, you might have to turn
off status bit ignore in order to determine the proper fleet
map.
Important: If you are scanning any system other than a
Motorola Type I system, be sure status bit ignore is set
to ONor you will miss some transmissions.
Follow these steps to turn status bit ignore on or off.
1. Hold down SCAN until the current status bit ignore
setting (ONor OFF) appears.
2. Press 8 to select ON or 9 to select OFF, then
press E (SVC).
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Identifying a Trunked Frequency
While ID scanning (looking for IDs within a trunked sys-
tem) or performing an ID search, press 9 to see the
current trunked frequency. (The frequency flashes
twice.) Then hold down 9 until a confirmation tone
sounds and the ID and the frequency alternately appear.
To return to normal operation, press 9.
Selecting the EDACS Talk Group ID Format
The EDACS system uses two group ID formats: Decimal
and Agency-Fleet-Subfleet (AFS). If you use a list of IDs
shown in one format (for example AFS) and the ID you
want to receive is in the other format (for example, deci-
mal), press SVC (E) to switch to the decimal format. The
ID appears in decimal format. Eflashes on the display
when the decimal format is selected.
EDACS Talk Group ID Range Search
To search EDACS IDs faster, set a range for the Agency
or Fleet listings. Enter the Agency (or the Agency and
the Fleet) listing numbers using the number keys, then
press SRC (LIMIT). Note the following examples.
Example 1
Agency = 01
Press 0 1 . SRC (LIMIT)
01---appears during search.
Example 2
Agency = 01 Fleet = 01
Press 0 1 . 0 1 SRC (LIMIT)
01-01-appears during search.
To stop an ID range search, press SRC (LIMIT).
44
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Using HOLD to Monitor an
Active Talk Group ID
Follow these steps to stop scanning and keep the scan-
ner tuned to a desired ID.
1. Press HOLD (A/B). HOLDappears and the scanner
stays on the current ID.
2. If you want to listen to (and hold) a different ID, use
the number keys to enter that ID.
3. Press HOLD (A/B) again. HOLD flashes, then the
scanner monitors the ID.
4. Press SRC to resume searching for a data channel
(trunk scanning).
Temporarily Storing a Talk Group ID
into the Monitor ID Memory
To store a talk group ID into a temporary monitor memo-
ry, press MON/CLR (•). This lets you store the ID prior to
moving it into a list memory. Press SRC to resume
searching.
Note: To program the ID stored in the monitor ID memo-
ry into the ID scan list, see “Moving Talk Group IDs to
Talk Group ID Lists” on Page 49.
Locking Out Talk Group IDs
Many municipal and commercial services use trunk sys-
tems to transmit signals from such devices as water
meter transmitters, door alarms, and traffic signals.
Some signals are encrypted, as well, and most are not
voice signals. Since all these are assigned IDs just like
other users, you may want to lock out reception of these
ID signals. You can lock out up to 100 IDs at one time.
Note: If you lock out an ID while searching, it is also
locked out of the scan list(s). See “Using Talk Group ID
Lists” on Page 48.
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
45
To lock out an ID, press L-OUT (S/S) when the ID ap-
pears. The ID is locked out, and the next active ID ap-
pears.
Unlocking a Single Talk Group ID
1. Hold down L-OUT (S/S) until you hear two short
beeps.
2. Repeatedly press 8 or 9 to select the ID you
want to unlock.
3. Press L-OUT (S/S). The ID is unlocked, and the
next locked ID appears.
4. Press SRC (LIMIT) to resume the scanner’s previ-
ously selected function.
Unlocking All Talk Group IDs
Hold down L-OUT (S/S) while searching until you hear
two short beeps, then press E (SVC) to unlock all the IDs
at once. The scanner beeps twice. Press L-OUT/SS to re-
sume the search.
Note: When you unlock all the IDs, the scan list appears.
Press SCAN to scan the IDs stored in your scan lists or
press SRC (LIMIT) to resume the scanner’s previously se-
lected function. For more information about scan lists,
see “Using Talk Group ID Lists” on Page 48.
Using Trunk Scanning Scan Delay
Sometimes a user might pause before replying to a
transmission. You can set the scanner to hold on an ID
for 5 seconds to wait for a reply. That way, the scanner
continues to monitor the ID for 5 seconds after the trans-
mission stops before resuming scanning.
Press DELAY to turn trunk scanning scan delay on or off.
DLYappears when the scan delay is set to on.
Note: If you consistently miss responses even with scan
delay turned on, change the default system type or the
fleet map being used. See “Scanning Type I and Hybrid
Trunked Systems” on Page 51.
46
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Monitoring Talk Group IDs
You can use your scanner’s display to monitor the fre-
quencies/talk group IDs of a trunked system for activity.
While you cannot hear conversations in this mode, it is
an excellent way to determine which talk group IDs are
the most active. To set the scanner to monitor IDs, hold
down MON/CLR (•) until SEARCHand the channel num-
ber flash. All active group IDs appear in quick succes-
sion. To stop monitoring IDs, press SRC again.
Note: When you monitor IDs, any IDs you have locked
out also appear.
CHANNEL ACTIVITY BARS
Your scanner displays up to 20 channel activity bars for
the stored frequencies in a bank. These bars indicate the
activity taking place on a trunked system. By observing
these bars, you can see how many frequencies are be-
ing used and generally monitor how much communica-
tion traffic occurs.
Each frequency you store in a trunking bank has a corre-
sponding activity bar. However, there are only 20 bars
for a possible maximum of 50 frequencies. If the trunk
system contains more than 20 frequencies, some bars
will represent more than one frequency.
• If a bar appears steadily without any voice transmis-
sion, it represents the frequency in use as the data
channel.
• If a bar appears and flashes when an ID appears,
the bar represents the frequency being used by the
trunk system transmitter.
• If a bar appears without any voice transmission, the
channel is probably being used for a telephone
interconnect call or a private call, or the bar might
be a locked-out ID. Your scanner does not monitor
these types of calls.
• If the scanner is holding on an ID which is not being
used, the other activity bars turn on and off as other
groups use the system.
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
47
USING TALK GROUP ID LISTS
When you program trunked frequencies into a bank (see
“Storing Trunked Frequencies” on Page 40), your scan-
ner sets up five scan lists for that one bank in which you
can store your favorite IDs. Each list can contain up to
10 IDs, for a total of 50 IDs for each trunk scanning
bank. If you use all the banks as trunking banks, you can
store 1000 IDs.
Talk group ID lists help you to organize trunking system
users into categories. For example, you might use List 1
for police IDs, List 2 for fire department IDs, List 3 for
emergency medical service IDs, and so on. Once you
store all the IDs in a list, you can scan them just as you
scan conventional channels. You can program IDs into
talk group ID lists manually, during a search, or automat-
ically.
Manually Storing Talk Group IDs
in Talk Group ID Lists
1. Select the trunking bank you want to use (see
“Searching a Trunked Bank” on Page 42).
2. After the scanner begins trunk scanning, press
MAN. A number showing the current talk group ID
list appears at the top of the display, and bars
appear that show activity in other banks.
3. Press MAN again, then repeatedly press 8 or 9 to
select the talk group ID list location (shown at the
top of the display) where you want to store an ID.
Then press PROG.
4. Enter the type of ID you want to store, then press E.
To enter a Type I ID, use the number keys to enter
the block number and the fleet number, then press
. Enter the subfleet number and press E.
•
To enter an EDACS ID, use the number keys to
enter the agency number, then press . Next, enter
•
the fleet number and the subfleet number, then
press E.
48
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: To clear a mistake while entering an ID, press
0 then E, then start over at Step 1.
5. Repeatedly press PROG or 8 to select the next
scan list location you want to program. Then repeat
Step 4 to enter another ID.
6. When you finish, press E to store the entries.
Entering EDACS Partial Talk Groups
You can enter partial group numbers in an EDACS talk
group. By entering only the desired portion of a group,
you can select either 128, 8, or 1 talk group. For exam-
ple, you might program every talk group in a police de-
partment by pressing just four keys.
Note: You cannot use partial talk groups in decimal
mode. (See “Selecting the EDACS Talk Group ID For-
mat” on Page 44.)
You can program a specific talk group such as 01-011
into the scan list memory. In AFS mode, you can pro-
gram the talk groups for an entire agency by pressing
corresponding keys.
For example:
You Press
To Scan
01 . E
all 01 groups
01 . 01 E
all 01 talk groups within
the 01 agency
To lock out a large number of talk groups, press L-OUT
after entering an agency or an agency and fleet into
memory.
Note: In AFS mode, agency numbers range from 00–15.
Moving Talk Group IDs to
Talk Group ID Lists
1. Press MAN. MANappears.
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
49
2. Select the ID scan list location where you want to
store the IDs, then press PROG. PGMappears.
3. Press MON/CLR. A monitor ID appears.
4. Press E. The scanner stores the IDs into the
selected ID scan list.
Scanning the Talk Group ID Lists
Press SCAN to begin scanning the lists you have stored.
Note: If one or more of the IDs you stored are incorrect,
Error flashes twice and the scanner beeps several
times, then the scan list numbers appear at the top of the
display. To correct the entry, delete at least one of the in-
correct IDs (see “Deleting a Stored Talk Group ID List”).
To remove a scan list from active scanning, use the
number keys to enter the scan list’s number. The scan
list number turns off, and the IDs in that list are not
scanned.
Note: One of the five scan lists must always be active.
You cannot remove all of them.
To restore a scan list to active scanning, use the number
keys to enter the number of the list again.
Press SRC to return to the previously selected function.
Deleting a Stored Talk Group ID List
1. Press PROG. PGMappears.
2. Repeatedly press 8 or 9 to select the talk group
ID list location (shown at the top of the display) you
want to delete.
3. Press 0 then E.
Priority Talk Group ID Scanning
You can assign a priority to a favorite ID so during scan-
ning the scanner checks that ID more frequently than the
others in the list. Each of the five memory locations re-
50
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
served for storing lists (see “Using Talk Group ID Lists”
on Page 48) can have only one priority ID, and the ID as-
signed that priority in List 1 has the highest priority of all.
To assign a priority to an ID, press PROG. Enter the de-
sired ID number (list number and location number), then
press PRIORITY (H/S). Pappears.
To turn priority ID scanning on or off, repeatedly press
PRIORITY (H/S) during ID scanning or manual operation.
PRIappears when priority scanning is turned on.
Note: Priority ID scanning does not operate when priori-
ty IDs are locked out. See “Locking Out Talk Group IDs”
on Page 45.
SCANNING TYPE I AND HYBRID
TRUNKED SYSTEMS
Your scanner is preset to scan Type II system IDs. When
you scan trunked frequencies, each Type II user ID you
see appears as an even number without a dash (exam-
ple 2160). Your scanner can also scan Type I trunked
systems. Each Type I ID appears as a three- or four-digit
number, followed by a hyphen, followed by a one- or
two-digit number (example 200-14).
If you notice a mix of odd- and even-user IDs (examples
6477, 2160, 6481, 6144, and 1167), then you are proba-
bly monitoring either a Type I or hybrid (a combination of
Type I and Type II user IDs) system with the S-Bit func-
tion turned off (see “Types of Trunking Systems” on
Page 38 and “Turning the Status Bit Ignore (S-Bit)
On or Off” on Page 43).
Subfleet information is included with the frequency list
for a Type I system. To enter the provided map, see
“Programming a Fleet Map” on Page 55.
Note: To locate suitable fleet map information, review
If you do not already know the size codes used, you will
have to guess. Since you do not have to figure out all the
blocks at one time, this is not as hard as it might seem.
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
51
Select a size code for a block, then press SRC and listen
to the conversations. If you are receiving most of the re-
plies, then you have probably selected the right size
code and can program the next block of the map. There
are 16 preset fleet maps to choose from, and it is best to
start with these when setting up a Type I or hybrid trunk
scanning bank. If none of the following preset fleet maps
allow you to follow complete conversations, then you
probably need to program your own fleet map (see “Pro-
gramming a Fleet Map” on Page 55).
E1P1
E1P2
E1P3
Size
Size
Size
Block
Code
S11
S11
S11
S11
S11
S11
S11
S11
Block
Code
Block
Code
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
S4
0
1
2
3
4
5
6
7
S4
S4
S4
S4
S4
S4
S4
S4
S4
S4
S4
S4
S12
(S12)
S4
E1P4
E1P5
E1P6
Size
Size
Size
Block
Code
Block
Code
Block
Code
0
1
2
3
4
5
6
7
S12
(S12)
S4
0
1
2
3
4
5
6
7
S4
0
1
2
3
4
5
6
7
S3
S4
S10
S4
S12
(S12)
S4
S4
S4
S4
S12
(S12)
S12
(S12)
S4
S4
S4
S4
S4
S4
52
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
E1P7
E1P8
E1P9
Size
Size
Size
Block
Code
S10
S10
S11
S4
Block
Code
Block
Code
0
1
2
3
4
5
6
7
0
1
2
3
4
5
6
7
S1
0
1
2
3
4
5
6
7
S4
S4
S0
S0
S0
S0
S0
S0
S1
S2
S2
S4
S3
S4
S3
S4
S4
S4
S4
E1P10
E1P11
E1P12
Size
Size
Size
Block
Code
Block
Code
Block
Code
0
1
2
3
4
5
6
7
S0
S0
S0
S0
S0
S0
S4
S4
0
1
2
3
4
5
6
7
S4
S0
S0
S0
S0
S0
S0
S0
0
1
2
3
4
5
6
7
S0
S0
S0
S0
S0
S0
S0
S4
E1P13
E1P14
E1P15
Size
Size
Size
Block
Code
Block
Code
Block
Code
0
1
2
3
S3
S3
S11
S4
0
1
2
3
S4
0
1
2
3
S4
S4
S4
S11
S3
S10
S4
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
53
4
5
6
7
S4
S0
S0
S0
4
5
6
7
S4
4
5
6
7
S11
S0
S4
S12
(S12)
S12
(S12)
E1P16
Size
Block
Code
0
1
2
3
4
5
6
7
S3
S10
S10
S11
S0
S0
S12
(S12)
Selecting a Preset Fleet Map
1. Set the scanner for conventional scanning and
press PROG then TRUNK to select the bank to store
the fleet map.
2. Press a number key to select the bank to store the
fleet map.
3. Repeatedly press 8 or 9 to select E1, then press
E. A previously programmed trunked frequency
appears.
4. Press DATA (ALT).
5. Repeatedly press 8 or 9 to select the name of
the desired map (example E1P7). The prepro-
grammed fleet map appears.
6. Press E (SVC), then press SRC (LIMIT). The scanner
then searches for transmissions using the preset
map you chose.
54
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: When the scanner searches for transmissions,
you see Type I fleet and subfleet IDs such as 100-12,
100-9, 000-12, or 400-8.
How do you know if the preset map you selected is cor-
rect? Listen to find out if you are following complete con-
versations. If not, try another preset map.
Programming a Fleet Map
1. Set the scanner for conventional scanning. Press
PROG then TRUNK.
2. Press the number key of the bank where you want
to store the fleet map.
3. Repeatedly press8 or 9 until E1 appears, then
press E. A trunked frequency you previously pro-
grammed appears.
4. Press DATA. A preprogrammed fleet map appears.
5. Repeatedly press 8 or 9 until USr appears.
Then press E.
6. Press DATA.
7. Repeatedly press 8 or 9 to select the size code
for the first block, then press E. The next available
block appears.
Size Code
Block
8. Repeat Step 7 until you have selected a size code
for each desired block.
9. Press SRC (LIMIT). The scanner exits the trunking
programming mode, tunes the data channel, then
searches using the map you programmed.
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
55
Note: If you select size code S-12, S-13, or S-14, these
restrictions apply:
• S-12 can only be assigned to Blocks 0, 2, 4, or 6
• S-13 can only be assigned to Blocks 0 and 4
• S-14 can only be assigned to Block 0
Since these size codes require multiple blocks, you will
be prompted for the next available block when you pro-
gram a fleet map. For example, if you assign Block 0 as
S-12, the scanner prompts you for b2, the next block
available, instead of b1. If you assign Block 0 as S-14,
you would not see another prompt because S-14 uses
all available blocks.
Programming the Base and
Offset Frequencies
To properly track Motorola VHF and UHF trunked sys-
tems, you must program the applicable base and offset
frequencies for each system.
For a list of these frequencies and other scanner infor-
frequency resources.
1. Set the scanner for conventional scanning. Press
PROG then TRUNK.
2. Press the number key of the bank where you want
to store the base frequency.
3. Repeatedly press 8 or 9 to select E2-VHi or
E2-UHF, then press E. A previously programmed
trunked frequency appears.
4. Press DATA (ALT). The preset base frequency
appears.
5. Enter a desired frequency.
6. Press DATA (ALT). The preset offset frequency
appears.
56
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Enter the frequency using the number keys accord-
ing to the following guide:
• For Motorola Type II VHF, (E2-VHF Hi band) use
5kHz steps between 5 kHz – 100 kHz.
• For Motorola Type II UHF, (E2-UHF band) use
12.5kHz steps between 12.5 kHz – 100 kHz.
Programming a Hybrid System
A hybrid system is simply a Type I system with some of
its blocks designated as Type II blocks. To program a
hybrid system, follow the steps listed in “Programming a
Fleet Map” on Page 55. However, if you want a block to
be Type II, instead of pressing 8 or 9 to select the
size block (Step 7), enter size code S-0instead.
Turning On/Off the Motorola Disconnect
Tone Detect Function
While trunking a Motorola system, your scanner auto-
matically tunes to the data channel when it detects a dis-
connect tone (a code that tells the trunking system that
the transmitter has finished sending) on the voice chan-
nel.
You can manually turn off this function so the scanner
does not tune to the data channel under those condi-
tions. You might use this feature to listen to weak trans-
missions when conversations are generally disconnect-
ed.
To turn the disconnect tone detect function on or off, set
the scanner to trunk track then press SVC. The scanner
beeps and DATAflashes for about 5 seconds.
Notes:
• To set the scanner so it remains on the voice chan-
nel (even when a disconnect tone is transmitted or
there is no signal at all) set SQUELCH so you hear a
hissing.
Trunking Operation
Download from Www.Somanuals.com. All Manuals Search And Download.
57
• You cannot use the disconnect tone detect function
if you are programming a trunking frequency or a
fleet map.
To set the scanner to automatically tune to the data
channel once again when it detects a disconnect tone,
press SVC (E) .
ˆ A General Guide to
Scanning
Your scanner’s reception is mainly “line-of-sight.” You
usually cannot hear stations that are beyond the horizon.
GUIDE TO FREQUENCIES
National Weather Frequencies
162.400
162.425
162.450
162.475
162.500
162.525
162.550
Birdie Frequencies
Every scanner has birdie frequencies. Birdies are sig-
nals created by the scanner’s internal circuits. These
stray frequencies might interfere with broadcasts on the
same or similar frequencies. If you program one of these
frequencies, you hear only noise on that frequency. If the
interference is not severe, you might be able to turn
SQUELCH clockwise to cut out the birdie.
This scanner’s known birdie frequencies (in MHz) are:
41.6000
407.7625
415.0000
485.4625
906.4125
145.6000
407.8125
435.9250
489.2500
906.5875
165.3000
413.1750
455.7375
823.8000
926.7000
171.2500
413.2250
465.6500
899.2375
1290.7000
58
A General Guide to Scanning
Download from Www.Somanuals.com. All Manuals Search And Download.
GUIDE TO THE ACTION BANDS
Typical Band Usage
VHF Band
Low Range
29.00–50.00 MHz
6-m Amateur
U.S. Government
2-m Amateur
High Range
50.00–54.00 MHz
137.00–144.00 MHz
144.00–148.00 MHz
148.00–174.00 MHz
216.00–225.00 MHz
1-m Amateur
UHF Band
U.S. Government
70-cm Amateur
Low Range
FM-TV Audio Broadcast, Wide
Band
406.00–420.00 MHz
420.00–450.00 MHz
450.00–470.00 MHz
470.00–512.00 MHz
Public Service
806.00–823.93 MHz
851.00–856.00 MHz
Conventional Systems
Conventional/Trunked
Systems
Trunked Systems
Public Safety
856.00–861.00 MHz
861.00–866.00 MHz
866.00–868.93 MHz
896.11–902.00 MHz
902.00–928.00 MHz
935.00–940.00 MHz
940.00–941.00 MHz
941.00–944.00 MHz
High Range
33-cm Amateur
Private Trunked
General Trunked
Fixed Services
Studio-to-Transmitter
Broadcast Links
Private Fixed Services, Paging
25-cm Amateur
944.00–952.00 MHz
952.00–956.00 MHz
1240.00–1300.00MHz
Primary Usage
As a general rule, most of the radio activity is concentrat-
ed on the following frequencies:
VHF Band
Activities
Frequencies
Government, Police, and Fire
Emergency Services
Railroad
153.785–155.980 MHz
158.730–159.460 MHz
160.000–161.900 MHz
A General Guide to Scanning
Download from Www.Somanuals.com. All Manuals Search And Download.
59
UHF Band
Activities
Frequencies
Land-Mobile “Paired”
Frequencies
450.000–470.000 MHz
451.025–454.950 MHz
456.025–459.950 MHz
460.025–464.975 MHz
465.025–469.975 MHz
Base Stations
Mobile Units
Repeater Units
Control Stations
Note: Remote control stations and mobile units operate
at 5 MHz higher than their associated base stations and
relay repeater units.
BAND ALLOCATION
Use the following listing of the typical services within
your scanner’s frequency coverage to assist you to de-
cide which frequency ranges to scan. These frequencies
are subject to change, and might vary from area to area.
For a more complete listing, refer to the Police Call Ra-
dio Guide including Fire and Emergency Services, avail-
able at your local RadioShack store.
Abbreviations
Services
BIFC ................................... Boise (ID) Interagency Fire Cache
BUS .......................................................................... Business
CAP .................................................................. Civil Air Patrol
CB .................................................................... Citizens Band
CCA .............................................................. Common Carrier
CSB ..................................................... Conventional Systems
CTSB ..................................... Conventional/Trunked Systems
FIRE .............................................................. Fire Department
HAM ..................................................... Amateur (Ham) Radio
GOVT ..................................................... Federal Government
GMR ..................................................... General Mobile Radio
GTR ................................................................ General Trunked
IND .............................................................. Industrial Services
(Manufacturing, Construction, Farming, Forest Products)
MAR ................................................... Military Amateur Radio
MARI .................................................. Maritime Limited Coast
(Coast Guard, Marine Telephone,
Shipboard Radio, Private Stations)
MARS ...................................... Military Affiliate Radio System
MED ......................................... Emergency/Medical Services
MIL ...................................................................... U.S. Military
MOV ......................................... Motion Picture/Video Industry
NEW ........................................................ New Mobile Narrow
NEWS .............................. Relay Press (Newspaper Reporters)
OIL ......................................................... Oil/Petroleum Industry
POL ............................................................. Police Department
60
A General Guide to Scanning
Download from Www.Somanuals.com. All Manuals Search And Download.
PUB .................................................................. Public Services
(Public Safety, Local Government, Forestry Conservation)
PSB ...................................................................... Public Safety
PTR ................................................................. Private Trunked
ROAD ....................................... Road & Highway Maintenance
RTV ................................. Radio/TV Remote Broadcast Pickup
TAXI ..................................................................... Taxi Services
TELB ............................................................ Mobile Telephone
(Aircraft, Radio Common Carrier, Landline Companies)
TELC ............................................................. Cordless Phones
TELM .................................................. Telephone Maintenance
TOW ....................................................................... Tow Trucks
TRAN .................................................. Transportation Services
(Trucks, Tow Trucks, Buses, Railroad, Other)
TSB ............................................................... Trunked Systems
TVn ..................................................... FM-TV Audio Broadcast
USXX .................................................... Government Classified
UTIL ...................................................... Power & Water Utilities
WTHR .......................................................................... Weather
VERY HIGH FREQUENCY (VHF)
VHF Low Band—(29–50 MHz—in 5 kHz steps)
29.000–29.700 ................................................................. HAM
29.900–30.550 ....................................................... GOVT, MIL
30.580–31.980 .......................................................... IND, PUB
32.000–32.990 ....................................................... GOVT, MIL
33.020–33.980 ................................................ BUS, IND, PUB
34.010–34.990 ....................................................... GOVT, MIL
35.020–35.980 ..................................... BUS, PUB, IND, TELM
36.000–36.230 ....................................................... GOVT, MIL
36.250 ............................................................ Oil Spill Cleanup
36.270–36.990 ....................................................... GOVT, MIL
37.020–37.980 .......................................................... PUB, IND
38.000–39.000 ....................................................... GOVT, MIL
39.020–39.980 .................................................................. PUB
40.000–42.000 ............................................ GOVT, MIL, MARI
42.020–42.940 .................................................................. POL
42.960–43.180 ................................................................... IND
43.220–43.680 .............................................. TELM, IND, PUB
43.700–44.600 ............................................................... TRAN
44.620–46.580 ......................................................... POL, PUB
46.600–46.990 .................................................... GOVT, TELC
47.020–47.400 .................................................................. PUB
47.420 ..................................................... American Red Cross
47.440–49.580 .......................................................... IND, PUB
49.610–49.990 ........................................................ MIL, TELC
6-m Amateur Band—(50–54 MHz)
50.00–54.00 ..................................................................... HAM
Aircraft Band—(108–137 MHz)
108.00–121.490 ................................................................. AIR
121.500 ........................................................... AIR Emergency
121.510–136.000 ............................................................... AIR
U.S. Government Band (137–144 MHz)
137.000–144.000 .................................................... GOVT, MIL
2-m Amateur Band (144–148 MHz)
144.000–148.000 .............................................................. HAM
A General Guide to Scanning
Download from Www.Somanuals.com. All Manuals Search And Download.
61
VHF High Band (148–174 MHz)
148.050–150.345 ............................................. CAP, MAR, MIL
150.775–150.790 .............................................................. MED
150.815–150.980 ................................. TOW, Oil Spill Cleanup
150.995–151.475 .................................................. ROAD, POL
151.490–151.955 ...................................................... IND, BUS
151.985 ........................................................................... TELM
152.0075 ........................................................................... MED
152.030–152.240 ............................................................. TELB
152.270–152.480 ............................................ IND, TAXI, BUS
152.510–152.840 ............................................................. TELB
152.870–153.020 ..................................................... IND, MOV
153.035–153.725 .............................................. IND, OIL, UTIL
153.740–154.445 .................................................... PUB, FIRE
154.490–154.570 ...................................................... IND, BUS
154.585 .......................................................... Oil Spill Cleanup
154.600–154.625 .............................................................. BUS
154.655–156.240 ............................... MED, ROAD, POL, PUB
156.255–157.425 ..................................................... OIL, MARI
157.450 ............................................................................. MED
157.470–157.515 ............................................................. TOW
157.530–157.725 ...................................................... IND, TAXI
157.740 ............................................................................. BUS
157.770–158.100 ............................................................. TELB
158.130–158.460 ......................... BUS, IND, OIL, TELM, UTIL
158.490–158.700 ............................................................. TELB
158.730–159.465 ......................................... POL, PUB, ROAD
159.480 ............................................................................... OIL
159.495–161.565 ............................................................ TRAN
161.580–162.000 ............................................ OIL, MARI, RTV
162.0125–162.35 ........................................ GOVT, MIL, USXX
162.400–162.550 ........................................................... WTHR
162.5625–162.6375 .................................... GOVT, MIL, USXX
162.6625 ........................................................................... MED
162.6875–163.225 ...................................... GOVT, MIL, USXX
163.250 ............................................................................. MED
163.275–166.225 ........................................ GOVT, MIL, USXX
166.250 ........................................................ GOVT, RTV, FIRE
166.275–169.400 .................................................. GOVT, BIFC
169.445–169.505 ................................. Wireless Mikes, GOVT
169.55–169.9875 ........................................ GOVT, MIL, USXX
170.000–170.150 ............................... BIFC, GOVT, RTV, FIRE
170.175–170.225 ........................................................... GOVT
170.245–170.305 ............................................. Wireless Mikes
170.350–170.400 .................................................... GOVT, MIL
170.425–170.450 ............................................................. BIFC
170.475 ............................................................................. PUB
170.4875–173.175 ...................... GOVT, PUB, Wireless Mikes
173.225–173.5375 ............................. MOV, NEWS, UTIL, MIL
173.5625–173.5875 ........................ MIL Medical/Crash Crews
173.60–173.9875 ........................................................... GOVT
216.00–224.9950 .............................................................. HAM
ULTRA HIGH FREQUENCY (UHF)
U. S. Government Band (406–420 MHz)
406.125–419.975 ................................................ GOVT, USXX
70-cm Amateur Band (420–450 MHz)
420.000–450.000 .............................................................. HAM
62
A General Guide to Scanning
Download from Www.Somanuals.com. All Manuals Search And Download.
Low Band (450–470 MHz)
450.050–450.925 .............................................................. RTV
451.025–452.025 .................................. IND, OIL, TELM, UTIL
452.0375–453.00 .................... IND, TAXI, TRAN TOW, NEWS
453.0125–454.000 .................................................... PUB, OIL
454.025–454.975 ............................................................. TELB
455.050–455.925 .............................................................. RTV
457.525–457.600 .............................................................. BUS
458.025–458.175 .............................................................. MED
460.0125–460.6375 ....................................... FIRE, POL, PUB
460.650–462.175 .............................................................. BUS
462.1875–462.450 .................................................... BUS, IND
462.4625–462.525 ................................ IND, OIL, TELM, UTIL
462.550–462.925 .................................................... GMR, BUS
462.9375–463.1875 .......................................................... MED
463.200–467.925 .............................................................. BUS
FM-TV Audio Broadcast, UHF Wide Band (470–512 MHz)
(Channels 14 through 69 in 6 MHz steps)
475.750 .................................................................. Channel 14
481.750 .................................................................. Channel 15
487.750 .................................................................. Channel 16
511.750 ................................................................... Channel 20
Note: Some cities use the 470–512 MHz band for land/
mobile service.
Conventional Systems Band — Locally Assigned
851.0125–855.9875 .......................................................... CSB
Conventional/Trunked Systems Band — Locally Assigned
856.0125–860.9875 ........................................................ CTSB
Trunked Systems Band — Locally Assigned
861.0125–865.9875 ........................................................... TSB
Public Safety Band — Locally Assigned
866.0125–868.9875 .......................................................... PSB
33-cm Amateur Band (902–928 MHz)
902.0000–928.0000 .......................................................... HAM
Private Trunked
935.0125–939.9875 .......................................................... PTR
General Trunked
940.0125–940.9875 .......................................................... GTR
25-cm Amateur Band
1240.0000–1300.0000 ...................................................... GTR
A General Guide to Scanning
Download from Www.Somanuals.com. All Manuals Search And Download.
63
FREQUENCY CONVERSION
The tuning location of a station can be expressed in fre-
quency (kHz or MHz) or in wavelength (meters). The fol-
lowing information can help you make the necessary
conversions.
1 MHz (million) = 1,000 kHz (thousand)
To convert MHz to kHz, multiply the number of mega-
hertz by 1,000:
9.62 (MHz) × 1000 = 9620 kHz
To convert from kHz to MHz, divide the number of kilo-
hertz by 1,000:
2780 (kHz) ÷ 1000 = 2.780 MHz
To convert MHz to meters, divide 300 by the number of
megahertz:
300 ÷ 7.1 MHz = 42.25 meters
64
A General Guide to Scanning
Download from Www.Somanuals.com. All Manuals Search And Download.
ˆ Troubleshooting
If your scanner is not working as it should, these sugges-
tions might help you eliminate the problem. If the scan-
ner still does not operate properly, take it to your local
RadioShack store for assistance.
Problem
Possible Cause
Remedy
Scanner is on but SQUELCH is not
Adjust SQUELCH.
will not scan.
adjusted cor-
rectly.
Only one channel Store frequencies
or no channels
are stored.
into more than one
channel.
Scanner is totally No power.
inoperative.
Check the batteries
or make sure the
AC adapter or DC
adapter is con-
nected properly.
Recharge the
rechargeable bat-
teries or replace the
non-rechargeable
batteries.
The AC adapter
Be sure the
or DC adapter is
not connected.
adapter’s barrel
plug is fully plugged
into the 9V 300 mA
jack.
The scanner’s
display dims or
the scanner
Batteries are not
correctly
installed.
Make sure the bat-
teries are installed
properly.
sounds a tone
every 15–30 sec-
onds.
The batteries are
weak.
Recharge the
rechargeable bat-
teries or replace the
non-rechargeable
batteries.
Troubleshooting
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Possible Cause
Remedy
The keypad does The keylock func- To turn off the key-
not work.
tion is activated.
lock, press KEY-
LOCK until K/L
disappears.
BATT.Lo
flashes.
The batteries are
weak.
Recharge the
rechargeable bat-
teries or replace the
non-rechargeable
batteries.
Poor or no recep- Batteries are
Check the batteries
or make sure the
AC adapter or DC
adapter is con-
tion.
weak or com-
pletely dis-
charged.
nected properly.
An antenna is not Make sure an
connected or is
connected incor-
rectly.
antenna is con-
nected to the scan-
ner.
Error
appears.
Programming
error.
Re-enter the fre-
quency correctly,
including the deci-
mal point.
The scanner
Stored frequen-
Avoid storing fre-
locks on frequen- cies are the same quencies listed
cies that have an
unclear transmis- quencies.
sion.
as “birdie” fre-
under “Birdie Fre-
quencies” on
Page 58, or only lis-
ten to them manu-
ally.
66
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Possible Cause
Remedy
The scanner
does not track a
trunked system.
The transmis-
sion might not
use a system that
can be tracked by
your scanner.
Scan another trans-
mission.
The data fre-
quency is miss-
ing.
Find the data fre-
quency (see “Stor-
ing Trunked
Frequencies” on
Page 40).
The system you
are trying to track
is a Type I sys-
tem, and the
scanner is set to
scan Type II sys-
tems.
Set the scanner to
receive Type I
trunked frequen-
cies. See “Scanning
Type I and Hybrid
Trunked Systems”
on Page 51.
Scanner is set to
receive Type I
trunked frequen-
cies, but does
not scan them.
The fleet map
you have select-
ed or entered
might be incor-
rect.
Check the fleet map
and correct it if nec-
essary (see “Scan-
ning Type I and
Hybrid Trunked
Systems” on
Page 51 and “Pro-
gramming a Fleet
Map” on Page 55).
Scanner does
not acquire a
data channel.
SQUELCH is not
correctlyadjusted trunk scanning. See
for trunk scan-
ning.
Adjust squelch for
“Setting Squelch for
the Trunking Mode”
on Page 40.
The frequency
used for the data
channel is miss-
ing.
Press SRC to
search for the data
channel (see “Stor-
ing Trunked Fre-
quencies” on
Page 40).
Troubleshooting
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Possible Cause
Remedy
Missing replies to The system you
Set the scanner to
receive Type I
conversations.
are trying to track
is a Type I sys-
tem, and the
trunked frequen-
cies. See “Scanning
Type I and Hybrid
Trunked Systems”
on Page 51.
scanner is set to
scan Type II sys-
tems.
The selected
Try another preset
fleet map is incor- fleet map or pro-
rect.
gram your own fleet
map (see “Scanning
Type I and Hybrid
Trunked Systems”
on Page 51).
Not all of the
trunk’s frequen-
cies have been
entered.
Enter all of the
trunk’s frequencies
(see “Storing
Trunked Frequen-
cies” on Page 40).
Channel activity
bars are flashing
but no sound is
heard.
The transmis-
Scan for another
transmission.
sion might be a
private or tele-
phone intercon-
nect call. The
scanner does not
scan these types
of transmissions.
The ID shown is
not active.
Wait for the ID to
become active, or
scan another trans-
mission.
RESETTING THE SCANNER
If the scanner’s display locks up or stops operating prop-
erly, you might need to reset the scanner.
Caution: This procedure clears all the information you
have stored in the scanner. Before you reset the scan-
ner, try turning it off and on to see if it begins working
properly. Reset the scanner only when you are sure it is
not working properly.
68
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Turn off the scanner.
2. While holding down 2 and 9, turn on the scanner.
CLEARflashes for about 5 seconds as the scanner
clears its memory.
Note: Do not turn off the scanner again until CLEAR
stops flashing. Otherwise, the scanner might not clear its
memory properly.
ˆ Care and Maintenance
Your RadioShack 1000-Channel Handheld Trunking
Scanner is an example of superior design and crafts-
manship. The following suggestions will help you care
for your scanner so you can enjoy it for years.
Keep the scanner dry. If it gets wet, wipe
it dry immediately. Liquids might contain
minerals that can corrode the electronic
circuits.
Use and store the scanner only in normal
temperature environments. Temperature
extremes can shorten the life of electronic
devices, damage batteries, and distort or
melt plastic parts.
Keep the scanner away from dust and
dirt, which can cause premature wear of
parts.
Handle the scanner gently and carefully.
Dropping it can damage circuit boards
and cases and can cause the scanner to
work improperly.
Use only fresh batteries of the required
size and recommended type. Batteries
can leak chemicals that damage your
scanner’s electronic parts.
Wipe the scanner with a damp cloth occa-
sionally to keep it looking new. Do not use
harsh chemicals, cleaning solvents, or
strong detergents to clean the scanner.
Care and Maintenance
Download from Www.Somanuals.com. All Manuals Search And Download.
69
Modifying or tampering with the scanner’s internal
components can cause a malfunction and might inval-
idate its warranty and void your FCC authorization to
operate it. If your scanner is not performing as it
should, take it to your local RadioShack store for as-
sistance.
ˆ Specifications
Frequency Coverage: .................. 29–54 MHz (in 5 kHz steps)
108–136.975 MHz (in 12.5 kHz steps)
137–174 MHz (in 5 kHz steps)
216–224.995 MHz (in 5 kHz steps)
406–512 MHz (in 12.5 kHz steps)
806.0000–823.9375 MHz (in 12.5 kHz steps)
851.0000–868.9875 MHz (in 12.5 kHz steps)
896.1125–956.0000 MHz (in 12.5 kHz steps)
1240.0000–1300.0000 MHz (in 12.5 kHz steps)
Monitor Channels ................................................................... 10
Number of Banks ................................................................... 20
Sensitivity (AM/FM):
FM ............................................... 20 dB S/N at 3 kHz deviation)
29–54 MHz.....................................................0.5 µV
137–174 MHz ............................................... 0.5 µV
216–225 MHz ............................................... 0.6 µV
406–512 MHz ............................................... 0.5 µV
806–956 MHz ............................................... 0.6 µV
1240–1300 MHz ........................................... 4.0 µV
AM ............................................ 20 dB S/N at 60% modulation)
108–136.9875 MHz ...................................... 1.5 µV
Spurious Rejection (at 40.84 MHz) ................................. 50 dB
Selectivity:
10 kHz –6 dB
15 kHz –50 dB
IF Rejection (at 162.4 MHz) ............................................ 80 dB
Channels ........................................................................... 1000
Operating Temperature ................. –4° to 140°F (–2°0 to 60°C)
Scan Speed ............................................. 50 Channels/Second
Search Speed:
Normal ......................................................... 100 Steps/Second
70
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
Hypersearch ................................................ 300 Steps/Second
Service ................................................ 50 Frequencies/Second
Priority Sampling ...................................................... 2 Seconds
Delay Time ............................................................... 2 Seconds
IF Frequencies ...................... 380.7 MHz, 10.85 MHz, 450 kHz
Antenna Impedance ........................................................... 50Ω
Audio Output ............................................... 350 mW maximum
Built-in Speaker ........................................ 17/16 Inches (36 mm)
8Ω Dynamic Type
Maximum Current Drain ............................................... 180 mA
Power Requirements:
4 AA Alkaline Batteries (6.0 VDC),
or 4 AA Rechargeable Ni-Cd Batteries (4.8 VDC)
or Optional AC Adapter
or Optional DC Adapter
Current Drain:
Squelched ..................................................... 70 mA
Full Output ...................................................180 mA
Dimensions (HWD) .......................................... 6 × 23/5 × 13/4 in
(153 × 66 × 44 mm)
Weight (without antenna, batteries, belt clip) .................. 8.2 oz
(232 g)
Specifications are typical; individual units might vary. Specifica-
tions are subject to change and improvement without notice.
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
71
Limited Ninety-Day Warranty
This product is warranted by RadioShack against manufacturing defects in
material and workmanship under normal use for ninety (90) days from the
date of purchase from RadioShack company-owned stores and authorized
RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN,
RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED
WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FIT-
NESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO
THE DURATION OF THE WRITTEN LIMITED WARRANTIES CON-
TAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL
HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY
OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY,
LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR
PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY
BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO,
ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME,
DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPE-
CIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF Ra-
dioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts
or the exclusion or limitation of incidental or consequential damages, so
the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the prod-
uct and the RadioShack sales receipt as proof of purchase date to any Ra-
dioShack store. RadioShack will, at its option, unless otherwise provided
by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c)
refund the purchase price. All replaced parts and products, and products
on which a refund is made, become the property of RadioShack. New or
reconditioned parts and products may be used in the performance of war-
ranty service. Repaired or replaced parts and products are warranted for
the remainder of the original warranty period. You will be charged for repair
or replacement of the product made after the expiration of the warranty pe-
riod.
This warranty does not cover: (a) damage or failure caused by or attribut-
able to acts of God, abuse, accident, misuse, improper or abnormal usage,
failure to follow instructions, improper installation or maintenance, alter-
ation, lightning or other incidence of excess voltage or current; (b) any re-
pairs other than those provided by a RadioShack Authorized Service
Facility; (c) consumables such as fuses or batteries; (d) cosmetic damage;
(e) transportation, shipping or insurance costs; or (f) costs of product re-
moval, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
RadioShack Customer Relations,
200 Taylor Street, 6th Floor, Fort Worth, TX 76102
12/99
We Service What We Sell
Cat. No. 20-524
A
RadioShack
UBZZ01306ZA
A Division of Tandy Corporation
Fort Worth, Texas 76102
04A00
Printed in the Philippines
Download from Www.Somanuals.com. All Manuals Search And Download.
|