Q See DVR 9004 User Guide

QR, QSDR, and 9004 Series  
Port Forwarding Instructions  
1
STEP 1. Select DHCP from the Type  
drop-down menu,  
STEP 2. Click on APPLY  
STEP 3. Select EXIT.  
NOTE! The DVR and PC must be connected to the same router.  
2
3
STEP 4. Restart the DVR.  
UPNP  
OFF  
Things you will need to know :  
1. The make and model of the router.  
PICTURE 3  
2. If you changed the default router login, then you will need to know the user name and  
password for that router.  
3. The IP address for the router.  
Once the DVR has restarted, reopen the  
Network Setup window and the IP address  
of the DVR will now be listed.  
4. You will be forwarding ports 80, 9000 and 18004.  
SECTION 1: FIND OUT THE IP ADDRESS OF DVR  
To nd out the IP of DVR for your DVR do the following:  
Forward ports 80 and 9000 to this IP  
address.  
Using the mouse, right-click and then select  
Main Menu in the pop-up menu.  
PICTURE 4  
If you are going to access the DVR from a  
smart phone you will also need to go the  
Mobile Setup and set up the DVR for smart  
phone access.  
Go to the Main Menu and click on the  
DEVICES icon.  
Then click on the MOBILE icon.  
PICTURE 5  
PICTURE 1  
Enter the User Name and Password you  
wish to use when accessing the DVR via a  
smartphone.  
Select NETWORK in the Main Menu  
window.  
Smartphones will access the DVR using port  
18004. This port will need to be forwarded  
along with ports 80 and 9000.  
PICTURE 2  
PICTURE 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Click on ADD CUSTOM.  
SECTION 3: DOWNLOAD SIMPLE PORT FORWARDING PROGRAM  
Download the FREE Simple Port Forwarding program from:  
Click on Download on Mirror 7 to download and install this program.  
PICTURE 11  
Once the program is installed, go to the  
Windows Start Menu (Windows icon in  
the lower left of your monitor) and look for  
Simple Port Forwarding in the program list.  
Click on the program to launch it.  
PICTURE 14  
Input the required information:  
Name: (You can name your DVR if you wish)  
Type: TCP  
Start Port: 80  
End Port:80  
PICTURE 12  
IP add: IP of DVR obtained in Step 1.  
Once Simple Port Forwarding has launched, select your router from the list. The default  
Router IP and Login information will automatically come up. If you have previously changed  
the login information, then you will have to enter it manually  
Click on ADD  
PICTURE 15  
Repeat for port 9000, and also for 18004 to allow smartphone access.  
PICTURE 13  
Click on “+” at the bottom to open the window allowing you to set your ports.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
You will now be returned to the main window of the program. The ports you added will now  
show on the list. Click on Update Router at the bottom.  
If for some reason, a port or ports that you forwarded are not listed in the Router and if you  
see a message in the Scripts list on the left side of the window stating that the port already  
exists (Red box in Picture 18), then you will need to change the Port 80 to 85 in the DVR  
and start over again.  
PICTURE 18  
Once you receive the DONE message that the ports have been successfully forwarded, test  
if the ports are working by clicking on item number 7 in the Check List - Test that the ports  
now work.  
PICTURE 16  
You will see the “Updating is in progress” message. Please wait until you see it say DONE at  
the bottom.  
PICTURE 17  
PICTURE 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Click on Begin.  
SECTION 4: SETTING UP DMZ IN ROUTER 2  
If you receive a message stating that the port is online and can be reached, then you have set  
it up correctly.  
NOTE! You will only need to proceed with this section if you detected a  
second router in Section 2.  
STEP 1. Login into Router 1 by putting  
the IP of Router 1 into the Internet  
Explorer browser, as in the example  
shown in Picture 21 where the IP  
address of Router 1 is 192.168.0.1  
STEP 2. Find the status page on the  
router settings that shows the WAN/  
Internet IP address and write it down  
this WAN IP address.  
STEP 3. Log into the Router 2 by putting  
the IP of Router 2 into the Internet  
Explorer browser, as in example  
shown in Picture 21 where the IP  
address of Router 2 is 192.168.1.1  
STEP 4. Find the DMZ page in the router  
settings.  
STEP 5. Enter the WAN IP for Router 1  
into the DMZ page and enable DMZ.  
PICTURE 21  
PICTURE 20  
NOTE! If you do not have a DMZ setting in the router, check to see if there  
To connect to your DVR from the Internet, you will need to put the Internet IP address shown  
is a Bridge setting. If so, then use the Bridge setting instead of DMZ.  
after “Your Internet Address:” message into the browser or access program window.  
STEP 6. Save your changes.  
If you are forwarding any other port instead of port 80, then you need to put that ports num-  
ber at the end of the address.  
You have forwarded the ports on the router to which the DVR is connected, to the IP address  
of the DVR, and set the primary router to pass the connection to this router.  
Example: if you use port 85, you will need to enter: http://75.14.251.43:85  
Instructions for using the ASee software on your smartphone can be found on the CD that  
came with your DVR, or it can be downloaded by clicking on the links below:  
Windows Mobile:  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Quantum Medical Alarms 9412 9112 A User Guide
Radio Shack Electronic Keyboard LK 1261 User Guide
Radio Shack MP3 Player Accessories 12 636 User Guide
Radio Shack Universal Remote TOUCHSCREEN REMOTE User Guide
RCA Microwave Oven RMW1167 User Guide
RedMax Edger HEZ2401S CA User Guide
Ryobi Chainsaw P545 User Guide
Samsung MP3 Player YP P2 User Guide
Samsung Printer ML 4500 User Guide
Sega Video Game Console 999 1108 User Guide