43-1104.fm Page 1 Wednesday, August 18, 1999 8:05 AM
Cat. No. 43-1104
OWNER’S MANUAL
Please read before using this equipment.
ET-1104
900 MHz Digital Spread Spectrum
Cordless Telephone
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 3 Wednesday, August 18, 1999 8:05 AM
This telephone has been tested and
found to comply with all applicable UL
and FCC standards.
We recommend you record your
phone’s serial number here. The num-
ber is on the bottom of the base.
Important:
Serial Number __________________
• Cordless phones such as this one
require AC power to operate. When
the AC power is off, you cannot dial
out or receive incoming calls using
your ET-1104. To be safe, you
should also have a phone that does
not need AC power to operate (not a
cordless phone) so you can still
make and receive calls if there is an
AC power failure.
Warning: To prevent fire or shock
hazard, do not expose this product
to rain or moisture.
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
• When AC power is lost, the ET-1104
loses the security access-protection
code connection between the base
and the handset. When power is re-
stored, put the handset on the base
briefly to restore this connection so
you can use the handset.
This symbol is intended to alert you to
the presence of uninsulated danger-
ous voltage within the product’s enclo-
sure that might be of sufficient
magnitude to constitute a risk of elec-
tric shock. Do not open the product’s
case.
This symbol is intended to inform you
that important operating and mainte-
nance instructions are included in the
literature accompanying this product.
!
3
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 4 Wednesday, August 18, 1999 8:05 AM
READ THIS BEFORE
INSTALLATION
FCC STATEMENT
Your telephone complies with Part 68 of
FCC Rules. Upon request, you must
provide the phone’s FCC registration
number and REN to your telephone
company. These numbers are on the
bottom of the base.
We have designed your phone to con-
form to federal regulations and you can
connect it to most phone lines. However,
each device that you connect to the tele-
phone line draws power from the line.
We refer to this power draw as the
phone’s ringer equivalence number, or
REN. The REN is on the bottom of your
phone.
Note: You must not connect your tele-
phone to:
• coin-operated systems
• party-line systems
If you use more than one phone or other
device on the line, add up all the RENs.
If the total is more than five, your phones
might not ring. In rural areas, a total
REN of three might impair ringer opera-
tion. If ringer operation is impaired, re-
move one of the devices from the line.
• most electronic key phone systems
4
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 5 Wednesday, August 18, 1999 8:05 AM
CONTENTS
Installation ............................................................................................................... 6
Mounting the Phone ........................................................................................... 6
On a Desk Top ............................................................................................. 6
On a Wall Plate ............................................................................................ 7
Directly on the Wall ...................................................................................... 8
Connecting and Charging the Battery Pack ..................................................... 10
Setting the Dialing Mode .................................................................................. 11
Setting the Ringer’s Tone and Volume ............................................................. 12
Operation ............................................................................................................... 13
Making and Receiving Calls ............................................................................. 13
Setting the Handset Volume ............................................................................. 13
Using Redial ..................................................................................................... 13
Using Mute ....................................................................................................... 14
Using Flash ...................................................................................................... 14
Using Tone Services on a Pulse Line ............................................................... 14
Paging .............................................................................................................. 15
Memory Dialing ................................................................................................ 15
Storing a Number in Memory ..................................................................... 15
Entering a Pause ....................................................................................... 16
Dialing a Memory Number ......................................................................... 16
Chain-Dialing Service Numbers ................................................................. 17
Testing Stored Emergency Numbers ......................................................... 17
Using a Headset ............................................................................................... 17
Troubleshooting .................................................................................................... 18
Care and Maintenance .......................................................................................... 20
Replacing the Battery Pack .............................................................................. 21
The FCC Wants You to Know ........................................................................... 22
Lightning ........................................................................................................... 22
5
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 6 Wednesday, August 18, 1999 8:05 AM
INSTALLATION
On a Desk Top
MOUNTING THE PHONE
Follow these steps when you place the
base on a desk or table.
You can place the ET-1104’s base on a
desk or table, mount it on a standard
wall plate, or mount it directly on a wall.
Choose a location that is:
1. Insert the bracket’s tabs into the
base’s upper tab slots, then press
down on the bracket’s clips and in-
sert them into the clip slots.
• near an AC outlet
• near a modular telephone line jack
• out of the way of normal activities
Clip Slots
Clips
• away from electrical machinery,
electrical appliances, metal walls or
filing cabinets, wireless intercoms,
alarms, and room monitors
• away from other cordless phones
Upper Tab Slots
The base’s location affects the hand-
set’s range. If you have a choice of sev-
eral locations, try each to see which
provides the best performance.
2. Plug one end of the supplied long
modular cord into the TEL LINE jack
on the back of the base.
Caution: The supplied RadioShack AC
adapter was designed specifically for
your ET-1104. Use only the supplied
adapter.
Notes:
3. Plug the cord’s other end into a
modular phone line jack.
• Your telephone connects directly to
a modular telephone line jack. If
your phone line jack is not modular,
you can update the wiring yourself,
using jacks and adapters available
at your local RadioShack store. Or,
you can let the phone company up-
date the wiring for you.
• The USOC number of the jack to be
installed is RJ11C, or RJ11W for a
wall plate jack.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 7 Wednesday, August 18, 1999 8:05 AM
4. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack on
the back of the base.
Lower
Tab
Slots
Tabs
Clip Slots
5. Route the adapter’s cord through
the strain relief slot on the bracket.
2. Plug one end of the supplied short
modular cord into the TEL LINE jack
on the back of the base.
Strain
Relief Slot
6. Plug the adapter into a standard AC
outlet.
3. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack on
the back of the base.
7. Lift the base’s antenna to a vertical
position.
4. Route the adapter’s cord through
the narrow groove on the bottom of
the bracket.
On a Wall Plate
1. Insert the bracket’s tabs into the
base’s lower tab slots, then press
down on the bracket’s clips and in-
sert them into the clip slots.
Narrow
Groove
7
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 8 Wednesday, August 18, 1999 8:05 AM
5. Plug the modular cord into the wall
plate jack, then align the bracket’s
keyhole slots with the wall plate
studs and slide the base downward
to secure it.
1. Drill two holes 315/16
inches (100 mm)
apart. Then thread a
screw into each hole,
letting the heads ex-
3/16"
3
tend about /16 inch (5
mm) from the wall.
15/16"
3
2. Insert the bracket’s tabs into the
base’s lower tab slots, then press
down on the bracket’s clips and in-
sert them into the clip slots.
6. Plug the adapter into a standard AC
outlet.
Lower
Tab
Slots
Tabs
7. Press and lift out the handset hold-
er, rotate it 180×, then snap it back
into place.
Clip Slots
3. Plug one end of the supplied long
modular cord into the TEL LINE jack
on the back of the base.
8. Lift the base’s antenna to a vertical
position.
Directly on the Wall
For this mounting method, you need two
flat-head screws (not supplied) with
heads that fit into the keyhole slots on
the bottom of the base.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 9 Wednesday, August 18, 1999 8:05 AM
4. Route the modular cord through the
wide groove on the bottom of the
bracket.
7. Align the keyhole slots with the
mounting screws and slide the base
downward to secure it.
Wide
Groove
5. Insert the supplied AC adapter’s
barrel plug into the DC IN 9V jack on
the back of the base.
8. Plug the modular cord into a modu-
lar phone line jack.
9. Plug the adapter into a standard AC
outlet.
6. Route the adapter’s cord through
the narrow groove on the bottom of
the bracket.
Narrow
Groove
10. Press and lift out the handset hold-
er, rotate it 180×, then snap it back
into place so it holds the handset.
11. Lift the base’s antenna to a vertical
position.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 10 Wednesday, August 18, 1999 8:05 AM
To charge the battery pack, place the
handset on the base either face-up or
face-down. The CHARGE indicator on
the base lights.
CONNECTING AND
CHARGING THE BATTERY
PACK
The ET-1104 comes with a rechargeable
nickel-cadmium battery pack in the
handset but not connected. Before using
your phone, you must connect the bat-
tery pack and then charge it for about 24
hours.
CHARGE Indicator
When the handset beeps and the LOW
BATT indicator on the handset flashes,
recharge the battery pack.
1. Press down and slide off the cover
as shown.
Notes:
• When you first use the phone after
charging or recharging the battery
pack, you might hear an error tone
(3 short beeps) or the phone might
2. Unfasten the plastic retainer strap
and lift the battery pack out of the
compartment. Plug the battery
pack’s connector into the socket in
the compartment. The connector fits
only one way.
TALK
not work when you press
. If
this happens, return the handset to
the base for a few seconds. This re-
sets the security access-protection
code.
• If the battery pack gets completely
discharged or the base loses power
while the handset is away from it,
the security access-protection code
needs to be reset. To reset the secu-
rity code, place the handset on the
base. If it was the handset that lost
power, leave the handset on the
base to charge the battery pack.
3. Place the battery pack inside the
compartment and fasten the retainer
strap.
• If the CHARGE indicator flickers
rapidly when you place the handset
on the base, be sure the battery
pack and AC adapter are correctly
and securely connected.
4. Replace the cover.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 11 Wednesday, August 18, 1999 8:05 AM
Also, check the charging contacts
on the handset and the base. If the
contacts are dirty or tarnished, clean
them with a pencil eraser.
pack from your local RadioShack
store (see “Replacing the Battery
Pack” on Page 21).
SETTING THE DIALING
MODE
DIAL MODE
Set
on the back of the base
for the type of service you have. If you
are not sure which type you have, once
the battery pack is fully charged, do this
test.
DIAL MODE
T
1. Be sure
(tone).
is set to
• If the battery pack becomes weak
during a call, you hear a beep every
4 seconds and the LOW BATT indi-
cator flashes. Recharge the battery
pack.
• About once a month, fully discharge
the battery pack by keeping the
handset off the base until the LOW
BATT indicator flashes. Otherwise,
the battery pack loses its ability to
fully recharge.
TALK
2. Lift the handset, press
listen for a dial tone.
, and
0
3. Press any number other than .
Note: If your phone system requires
that you dial an access code (9, for
example) before you dial an outside
number, do not press the access
code either.
• If the LOW BATT indicator does not
light and the phone does not work,
recharge the battery pack. (The bat-
tery power might be too low to light
the indicator.)
If the dial tone stops, you have
DIAL
touch-tone service. Leave
MODE
• If you are not going to use your
phone for an extended period of
time, disconnect the battery pack.
This increases the battery pack’s
usable life.
T
set to .
If the dial tone continues, you have
DIAL MODE
P
pulse service. Set
(pulse).
to
• The supplied battery pack should
last for about a year. When the bat-
tery pack loses its ability to fully re-
charge, order a replacement battery
11
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 12 Wednesday, August 18, 1999 8:05 AM
SETTING THE RINGER’S
TONE AND VOLUME
You can set four ringer tones and a high
and low volume for each.
To change the tone, lift the handset and
FLASH
press
. Then, enter the ringer
tone number (1–4) using the number
keys. The selected tone sounds briefly.
To hear and change the ringer volume
VOL
setting, press
s or t.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 13 Wednesday, August 18, 1999 8:05 AM
OPERATION
MAKING AND RECEIVING
CALLS
SETTING THE HANDSET
VOLUME
To make a call, lift the handset and
press TALK. The TALK indicator on the
handset and the IN USE indicator on the
base light. When you hear a dial tone,
dial the number.
You can choose one of four volume set-
tings for the handset. To change the vol-
ume, press VOL s or t during a call.
USING REDIAL
You can quickly dial the last number di-
aled. When you hear a dial tone, simply
press REDIAL.
To answer a call, simply lift the handset
from the base. If the handset is away
from the base, you can press any key to
answer a call.
Notes:
The ET-1104 scans 20 channels (fre-
quency pairs used between the base
and the handset) and automatically se-
lects a clear channel each time you
make or receive a call.
• The redial memory holds up to 32
digits, so you can redial long-
distance as well as local numbers.
• The redial memory also holds pause
entries. See “Entering a Pause” on
Page 16.
Note: If the handset is too far from the
base, the channel might not be clear.
Move closer to the base and try making
the call again.
• The redial memory does not store a
flash entry or any digits you press
after FLASH (see “Using Flash” on
Page 14).
To end a call, place the handset on the
base or press TALK.
TALK to hang up and
Note: If you press
the phone does not disconnect, press
TALK again while holding the handset
closer to the base, or place the handset
on the base.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 14 Wednesday, August 18, 1999 8:05 AM
USING MUTE
USING TONE SERVICES
ON A PULSE LINE
To talk to someone in the room without
the person on the other end of the
phone line hearing your conversation,
Some special services, such as bank-
by-phone, require tone signals. If you
have pulse service, you can still use
these special tone services by following
these steps.
MUTE
press
es.
. The MUTE indicator flash-
DIAL MODE
P
1. Be sure
is set to
(
)
pulse .
2. Dial the service’s main number.
3. When the service answers, press
TONE
(
). Any additional numbers
you dial are sent as tone signals.
MUTE
Press
again to resume your
phone conversation.
M
1
M2
M
3
M4
USING FLASH
FLASH
performs the electronic equiva-
4. After you complete the call, return
the handset to the base or press
lent of a switchhook operation for spe-
cial services, such as Call Waiting.
TALK
. The phone automatically re-
sets to the pulse mode.
For example, if you have Call Waiting,
FLASH
press
to answer an incoming call
without disconnecting the current call.
FLASH
Press
call.
again to return to the first
Note: If you do not have any special
FLASH
phone services, pressing
disconnect the current call.
might
14
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 15 Wednesday, August 18, 1999 8:05 AM
Storing a Number in Memory
PAGING
Note: An error tone sounds and the
phone exits the storing process if you
wait more than 30 seconds between
each key press.
To page the person who has the hand-
set or to locate the handset when the
PAGE
phone is not in use, press
on the
base. The handset beeps for about 15
seconds. To stop the beeping sooner,
1. Lift the handset.
TALK
press
on the handset twice or
PAGE
on the base.
MEM
. The TALK/MUTE LOW
2. Press
BATT indicator blinks.
3. Enter the number and any tone
mode changes or pause entries
(see “Entering
Page 16).
a
Pause” on
Notes:
• Make sure you press
stop the handset from beeping. If
TALK
twice to
Notes:
TALK
you press
dial tone.
only once, you get a
Each number you store can be up to
16 digits long.
• If you receive a call while the page
is sounding, the handset stops
beeping and starts ringing.
If you try to enter more than 16 dig-
its, the phone sounds an error tone
and exits the storing process. Start
over at Step 2.
Each tone or pause entry uses one
digit of memory.
MEMORY DIALING
The ET-1104 can store four telephone
numbers in speed dial memory, and you
can dial these numbers by pressing a
single button. You can also store up to
20 more numbers that you can dial by
entering a two-digit memory location
number.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 16 Wednesday, August 18, 1999 8:05 AM
4. To assign the number to a speed di-
al button, press MEM, then press a
speed dial button (M1–M4).
To delete a stored number, lift the hand-
set and press MEM twice, then enter the
memory location number (01–20) or
press the speed dial button (M1–M4) you
want to clear. The handset sounds a
long beep to signal that the memory lo-
cation is clear.
M2
M 3
M 4
M
1
Entering a Pause
To store the number in a standard
memory location, press MEM, then
enter the two-digit memory location
number (01–20).
In some telephone systems, you must
dial an access code (9, for example) and
wait for a second dial tone before you
can dial an outside number. You can
store the access code with the phone
number. However, you should also store
a pause after the access code to allow
the outside line time to connect. To en-
ter a 2-second pause, press PAUSE. For
a longer pause, press PAUSE additional
times.
The handset sounds a long beep to
indicate that the number is stored.
5. For each stored number, write the
person’s or company’s name next to
the appropriate location number on
the supplied memory directory stick-
er. (Use a pencil in case you need to
change the number later.) Peel the
backing off the sticker and attach it
to the phone.
Dialing a Memory Number
To dial a number assigned to a speed
dial button, simply press the button (M1–
M4) for the number you want to dial.
(You do not need to press TALK first.)
To replace a stored number, simply store
a new one in its place.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 17 Wednesday, August 18, 1999 8:05 AM
To dial a number stored in a standard
memory location, press TALK. When
you hear a dial tone, press MEM and en-
ter the two-digit memory location num-
ber for the number you want to dial.
USING A HEADSET
You can talk with hands-free convenience
using an optional headset that has a /32-
inch (2.5-mm) plug. Contact your local
RadioShack store for a suitable headset.
3
If you select an invalid memory lo-
Note:
cation (for example 3 instead of 03), the
phone sounds an error tone. Press MEM
again and re-enter the memory location
number.
To connect the headset, open the rub-
ber cover marked
on the side of the
handset, then insert the headset’s plug
into the jack.
Chain-Dialing Service Numbers
For quick recall of numbers for special
services (such as alternate long dis-
tance or bank-by-phone), store each
group of numbers in its own memory lo-
cation.
:
Notes
• Connecting a headset disconnects
the handset’s earpiece and micro-
phone.
Dial the service’s main number first.
Then, at the appropriate place in the
call, press the memory location button
(M1–M4), or press MEM and enter the
memory location number (01–20), for
the stored information.
• VOL on the handset also controls
the connected headset’s volume.
• If you place the handset on the base
while the headset is connected, be
sure the handset seats properly.
Testing Stored Emergency
Numbers
With a headset connected, you can
make or answer calls as usual using the
keys on the handset.
If you store an emergency service’s
number (police department, fire depart-
ment, ambulance) and you choose to
test the stored number, make the test
call during the late evening or early
morning hours to avoid peak demand
periods. Also, remain on the line to ex-
plain the reason for your call.
You can use a handset holder (available
from your local RadioShack store) to
hang the handset on your belt for greater
convenience.
When you finish using the headset, dis-
connect it and close the rubber cover to
protect the jack.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 18 Wednesday, August 18, 1999 8:05 AM
TROUBLESHOOTING
We do not expect you to have any problems with your ET-1104, but if you do, the fol-
lowing suggestions might help.
Problem
Suggestion
The phone does not work or works
poorly.
Be sure the base’s phone line cord and AC
adapter are correctly and securely con-
nected, and the battery pack in the handset
is charged.
Return the handset to the base for a few
seconds to reset the security access-pro-
tection code.
The handset stops working or works
poorly during a call.
Move the handset closer to the base.
Lift the base’s antenna to a fully vertical
position.
Be sure the handset’s battery pack is
charged. (If the battery pack power is too
low, it does not have enough power to light
the LOW BATT indicator.)
Low volume or unusual sounds.
Severe noise interference.
Someone has picked up another phone on
the same line. Hang up the other phone.
Keep the handset and base away from
computers, remote control toys, wireless
microphones, alarm systems, intercoms,
room monitors, fluorescent lights, and elec-
trical appliances.
Move to another location or turn off the
source of interference.
Hang up and redial the number.
The phone cannot be operated at a
useful distance from the base
because the signal becomes weak or
noisy (handset’s range has
decreased).
Lift the base’s antenna to a fully vertical
position.
Be sure neither the handset or base
antenna is touching a metal surface.
Recharge the battery pack.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 19 Wednesday, August 18, 1999 8:05 AM
Problem
Suggestion
The handset battery pack does not
charge.
Check the charging contacts on the hand-
set and base. If they are dirty, clean them
with a pencil eraser.
Be sure the battery pack is properly con-
nected.
Be sure the handset is properly seated on
the base.
Handset does not ring or receive a
page.
Lift the base’s antenna to a fully vertical
position.
Move the handset closer to the base.
Move the base away from other electrical
devices.
Recharge the battery pack.
If you still have problems, disconnect the phone. If other phones on the same line
work properly, the fault is in this phone or its installation. If you cannot find the prob-
lem, take your ET-1104 to your local RadioShack store for assistance.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 20 Wednesday, August 18, 1999 8:05 AM
CARE AND MAINTENANCE
Your ET-1104 900 MHz Digital Spread Spectrum Cordless Telephone is an example
of superior design and craftsmanship. The following suggestions will help you care for
your ET-1104 so you can enjoy it for years.
Keep the ET-1104 dry. If it gets wet, wipe it dry immediately. Liquids
might contain minerals that can corrode the electronic circuits.
Use and store the ET-1104 only in normal temperature environments.
Temperature extremes can shorten the life of electronic devices, dam-
age batteries, and distort or melt plastic parts.
Keep the ET-1104 away from dust and dirt, which can cause premature
wear of parts.
Handle the ET-1104 gently and carefully. Dropping it can damage cir-
cuit boards and cases and can cause the ET-1104 to work improperly.
Use a battery pack of the required size and recommended type. Batter-
ies can leak chemicals that damage your ET-1104’s electronic parts.
Wipe the ET-1104 with a damp cloth occasionally to keep it looking
new. Do not use harsh chemicals, cleaning solvents, or strong deter-
gents to clean the ET-1104.
Modifying or tampering with the ET-1104’s internal components can cause a malfunc-
tion and might invalidate it’s warranty and void your FCC authorization to operate it. If
your ET-1104 is not performing as it should, take it to your local RadioShack store for
assistance. If the trouble is affecting the telephone lines, the phone company can ask
you to disconnect your ET-1104 until you have resolved the problem.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 21 Wednesday, August 18, 1999 8:05 AM
REPLACING THE
BATTERY PACK
If you follow the instructions in “Connect-
ing and Charging the Battery Pack” on
Page 10, the battery pack should last
about one year. If the battery pack does
not hold a charge for more than 2 hours
after an overnight charge, replace it with
a new 3.6-volt, 600 mAh battery pack
with a connector that fits the socket in
the battery compartment. You can order
a replacement battery pack through your
local RadioShack store.
4. Replace the cover.
Cautions:
• You must use a replacement battery
pack of the same size and type.
• Do not dispose of the battery pack in
a fire because it might explode.
Install the new battery pack as de-
scribed below, then charge it for about
24 hours.
• Do not open or mutilate the battery
pack.
Note: To avoid losing phone numbers
stored in memory, try to install and begin
charging the new battery pack within 3
minutes.
• Be careful not to short the battery
pack by touching the connector’s
pins with conducting materials, such
as rings, bracelets, and keys. The
battery pack or conductor might
overheat and burn.
1. Press down and slide off the cover
as shown.
If you have trouble replacing the battery
pack, take the phone to your local Ra-
dioShack store for assistance.
Important: This product contains a re-
chargeable nickel-cadmium
battery
2. Unfasten the plastic retainer strap
and lift the battery pack out of the
compartment, then gently pull on the
battery connector to disconnect it.
pack. At the end of the battery pack’s
useful life, it must be recycled or dis-
posed of properly. Contact your local,
county, or state hazardous waste man-
agement authorities for information on
recycling or disposal programs in your
area. Some options that might be avail-
able are: municipal curb-side collection,
drop-off boxes at retailers such as your
local RadioShack store, recycling collec-
tion centers, and mail-back programs.
3. Insert the new battery pack’s con-
nector into the socket in the com-
partment, place the battery pack into
the compartment, and refasten the
retainer strap.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 22 Wednesday, August 18, 1999 8:05 AM
If you cannot eliminate the interference,
the FCC requires that you stop using
your phone.
THE FCC WANTS YOU TO
KNOW
In the unlikely event that your phone
causes problems on the phone line, the
phone company can temporarily discon-
tinue your service. If this happens, the
phone company attempts to notify you in
advance. If advance notice is not practi-
cal, the phone company notifies you as
soon as possible and advises you of
your right to file a complaint with the
FCC.
Some cordless telephones operate on
frequencies that might cause interfer-
ence to nearby TVs and VCRs. To mini-
mize or prevent such interference, the
base of the cordless telephone should
not be placed near or on top of a TV or
VCR.
LIGHTNING
Also, the phone company can make
changes to its lines, equipment, opera-
tions, or procedures that could affect the
operation of this telephone. The tele-
phone company notifies you of these
changes in advance, so you can take
the necessary steps to prevent interrup-
tion of your telephone service.
Your telephone has built-in lightning pro-
tection to reduce the risk of damage
from surges in telephone line and power
line current. This lightning protection
meets or exceeds FCC requirements.
However, lightning striking the tele-
phone or power lines can damage your
telephone.
Your phone might cause TV or radio in-
terference even when it is operating
properly. To determine whether your
phone is causing the interference, turn
off your phone. If the interference goes
away, your phone is causing it. Try to
eliminate the interference by:
Lightning damage is not common. Nev-
ertheless, if you live in an area that has
severe electrical storms, we suggest
that you unplug your phone during
storms to reduce the possibility of dam-
age.
• moving your phone away from the
receiver
• connecting your phone to an AC
outlet that is on a different electrical
circuit from the receiver
• contacting your local RadioShack
store for help
22
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 23 Wednesday, August 18, 1999 8:05 AM
NOTES
23
Download from Www.Somanuals.com. All Manuals Search And Download.
43-1104.fm Page 24 Wednesday, August 18, 1999 8:05 AM
Limited One-Year Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for one (1) year from the date of purchase from RadioShack company-owned
stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED
IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY
LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFOR-
MANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, IN-
CLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS
OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDEN-
TAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Some states do not allow the limitations on how long an implied warranty lasts or the exclusion of in-
cidental or consequential damages, so the above limitations or exclusions may not apply to you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, Dept. W, 100 Throckmorton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
8A8
Printed in the Philippines
Download from Www.Somanuals.com. All Manuals Search And Download.
|