;22/*\"%QTFNGUU"6GNGRJQPG
YKVJ"*GCFUGV",CEM
43-3533/3534/3541/3542/3543
10-Number Memory Dialing — lets you store up to 10
numbers (1 one-touch and 9 speed-dial) in memory for
easy dialing.
20 Channels — you can automatically select a clear
channel when you make or answer a call, or you can
manually change channels.
Ample Talk and Standby Time — the supplied battery
(when fully charged) provides about 7 hours of talk time or
14 days of standby time.
Page — lets you send a paging signal from the base to
the handset to page someone or locate the handset.
Quick Talk— lets you set the phone to answer a call by
simply lifting the handset from the base.
"+/2146#06"
#
#
If an icon appears at the end of a paragraph, go to the box on that
page with the corresponding icon for pertinent information.
— Warning — Important . — Caution
#
Rý
° — Hint ± — Note
OWNER’S MANUAL
Please read before using this equipment.
© 2002 RadioShack Corporation.
All Rights Reserved.
RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.
ENERGYSTAR and the ENERGYSTAR certification mark are registered US marks.
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Never push objects of any kind into this product through
cabinet slots as they may touch dangerous voltage
points or short out parts that could result in a risk of fire
or electric shock. Never spill liquid of any kind on the
product.
%106'065
s
n
Important Safety Instructions ..... 2
Introduction ................................ 4
Installation .................................. 4
Connecting and Charging the
i
t
c
u
r
t
s
In
ty
16. To reduce the risk of electric shock, do not disassemble
this product. Take it to a qualified service technician
when service or repair work is required. Opening or
removing covers may expose you to dangerous voltage
or other risks. Incorrect reassembly can cause electric
shock when the product is subsequently used.
Battery Pack ............................ 5
Setting the Ringer Tone .......... 6
Setting the Dialing Mode ......... 6
Operation ................................... 7
Making and Receiving Calls .... 7
Selecting the Channel ............. 7
Adjusting the Handset’s
Volume .................................... 7
Using Redial ............................ 7
Using Flash ............................. 7
Using Tone Services on a Pulse
Line ......................................... 8
Paging ..................................... 8
Using a Headset ..................... 8
Memory Dialing ....................... 8
Troubleshooting ....................... 10
Care .......................................... 11
Service and Repair .................... 11
Important Information ................ 11
FCC Statement ......................... 11
Lightning ............................... 12
f
a
S
t
n
t
r
o
p
Im
17. Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the
following conditions:
• When the power cord plug is damaged or frayed.
• If liquid has been spilled, into the product.
• If the product has been exposed to rain or water.
• If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions be-
cause improper adjustment of other controls may re-
sult in damage and will often require extensive work
by a qualified technician to restore the product to
normal operation.
• If the product has been dropped or the cabinet has
been damaged.
• If the product exhibits a distinct change in performance.
18. Avoid using a telephone (other than a cordless type)
during an electrical storm. There may be a remote risk
of electric shock from lightning.
19. Do not use the telephone to report a gas leak in the
vicinity of the leak.
$#66'4;"5#('6;"+05647%6+105".
1. Use only the appropriate type and size battery pack
specified in the instruction manual provided for this
product.
."%#76+10".
To reduce the risk of fire or injury,
read and follow these instructions.
2. Do not dispose of the battery pack in a fire. The cell
may explode. Check with local codes for possible
special disposal instructions.
3. Do not open or mutilate the battery pack. Released
electrolyte is corrosive and may cause damage to the
eyes or skin. It may be toxic if swallowed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Exercise care in handling the battery pack in order not
to short it with conducting materials such as rings,
bracelets, and keys. The battery or conductor may
overheat and cause burns.
"+/2146#06"
#
#
•
Cordless phones such as this
one require AC power to
operate. When the power is off,
you cannot make or receive
calls using your phone. To be
safe, you should also have a
phone that does not need AC
power to operate (not a cord-
less phone), so you can still
make and receive calls if there
is an AC power failure.
5. Charge the battery pack provided or identified for use
with this product only in accordance with the
instructions and limitations specified in the instruction
manual provided for this product.
6. Observe proper polarity orientation between the battery
pack and battery charger.
5#8'"6*'5'"+05647%6+105
•
When AC power is lost, the
phone loses the security
access-protection code con-
nection between the base and
the handset. When power is
restored, put the handset on
the base briefly to restore this
connection so you can use the
handset.
+0641&7%6+10
Thank you for purchasing the RadioShack 900 MHz Cord-
less Telephone. Your phone uses the 900 MHz band for less
interference, clearer sound, and greater range than 46/49
MHz cordless telephones. Its headset jack means you can
I
n
t
r
oduc
t
i
on
connect an optional headset for hands-free convenience.
#
•
Your phone operates on
standard radio frequencies as
allocated by the FCC. It is
possible for other radio units
operating nearby on similar
frequencies to unintentionally
intercept your conversation or
cause interference. This
+056#..#6+10
You can place the phone on a desk or table, or mount it on a
standard wall plate or directly on a wall. Select a location
that is:
possible lack of privacy can
occur with any cordless phone.
• near an accessible AC outlet
• near a telephone line jack
• out of the way of normal activities
."%#76+10".
You must use a Class 2
• away from electrical machinery, electrical appliances,
metal walls or filing cabinets, wireless intercoms,
alarms, and room monitors
power source that
!
supplies 9V DC and
delivers at least 210 mA. Its center
tip must be set to positive and its
• away from other cordless phones
The base’s location affects the handset’s range. If you have
a choice of several locations, try each to see which provides
the best performance..
plug must fit the phone's
DC IN 9V
jack. The supplied adapter meets
these specifications. Using an
adapter that does not meet these
specifications could damage the
phone or the adapter.
Your telephone connects directly to a modular telephone
line jack. If your telephone wiring does not have a modular
jack, you can update the wiring yourself using jacks and
adapters (available at your local RadioShack store or online
at RadioShack.com), or have the telephone company
update the wiring for you. You must use compatible modular
jacks that are compliant with Part 68 of FCC Rules. The
USOC number of the jack to be installed is RJ11C (or
RJ11W for a wall plate jack).
•
Always connect the AC adapter
to the phone before you connect it
to AC power. When you finish,
disconnect the adapter from AC
power before you disconnect it
from the phone.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
To mount the phone directly on a wall, you need two screws
(not supplied) with heads that fit into the keyhole slots on
15
16
the back of the base. Drill two holes 3 / inches (100 mm)
apart. Then thread a screw into each hole, letting the heads
1
8
extend about / inch (3 mm) from the wall.
1. Plug one end of the supplied modular cord (long for a
desktop or direct wall mounting, short for a wall plate)
into the TEL LINE jack on the bottom of the base.
2. Insert the supplied AC adapter’s barrel plug into the DC
IN 9V jack on the bottom of the base and route the
adapter’s cord through the strain relief slot on the base.
3. Route the adapter and modular cords
through the molded routing channels
on the back of the base as
Modular
Cord
shown here.
"+/2146#06"
#
#
4. For a wall plate, plug the other
end of the short modular cord into
The EPA certified
RBRC® Battery
Recycling Seal on
the nickel-cadmium
(Ni-Cd) battery
the wall plate jack.
AC Adapter Cord
5. For a wall plate or direct wall
mounting, align the base’s keyhole slots with the wall
plate studs or mounting screws and slide the base
down to secure it.
indicates RadioShack is voluntarily
participating in an industry
program to collect and recycle
these batteries at the end of their
useful life, when taken out of
service in the United States or
Canada. The RBRC program
provides a convenient alternative
to placing used Ni-Cd batteries
into the trash or the municipal
waste stream, which may be illegal
in your area. Please call 1-800-
THE-SHACK (1-800-843-7422) for
information on Ni-Cd battery
recycling and disposal bans/
restrictions in your area.
6. For a desktop or direct wall mounting, plug the other
end of the modular cord into a modular phone line jack.
n
o
7. Plug the adapter into a standard AC outlet.
t
a
l
l
a
t
%100'%6+0)"#0&"%*#4)+0)"6*'"$#66'4;"
s
In
2#%-
The phone comes with a rechargeable nickel-cadmium
battery pack in the handset, but not connected. Before using
your phone, you must connect the battery pack, then charge
it for about 15–20 hours.
#
1. Press down and slide off the battery compartment
cover in the direction of the arrow to remove it.
RadioShack’s involvement in this
program is part of the company’s
commitment to preserving our
environment and conserving our
natural resources.
2. Lift the battery pack out of the compartment.
3. Plug the battery pack’s connector into the socket in the
compartment (the connector fits only one way), then
place the battery pack in the compartment.
"9#40+0)
"
ý
R R
Dispose of the old battery pack
promptly and properly. Do not
burn or bury it. See “Battery Safety
Instructions” on Page 3 for
additional information on proper
battery handling.
4. Replace the cover.
To charge the battery pack, place the handset on the base.
The CHARGE/IN USE indicator on the base lights.
Recharge the battery pack when the handset beeps and
TALK/BATT flashes. R
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4'%*#4)+0)"6*'"$#66'4;"2#%-
• If the CHARGE/IN USE indicator does not light when
you place the handset on the base, be sure the battery
pack and AC adapter are correctly and securely con-
nected. Also, check the charging contacts on the hand-
set and the base. If the contacts are dirty or tarnished,
clean them with a pencil eraser.
• When you first use the phone after charging or
recharging the battery pack, the phone might not work
and you might hear an error tone. Return the handset
to the base for about 3 seconds to reset the security
access-protection code.
• If the battery pack becomes weak during a call, the
handset beeps every 3 seconds and TALK/BATT
flashes. When this happens, recharge the battery pack.
• If TALK/BATT does not light and the phone does not
work, recharge the battery pack. (The battery power
might be too low to light TALK/BATT.)
• About once a month, fully discharge the battery by
keeping the handset off the base until TALK/BATT
flashes. Otherwise, the battery pack loses its ability to
fully recharge.
• The handset loses its security access-protection code if
the battery pack is completely discharged. Place the
handset on the base to recharge the battery pack and
reset the code.
• If you are not going to use your phone for an extended
period, disconnect the battery pack. This increases the
battery pack’s usable life.
In
s
t
a
la
ti
The supplied battery pack should last for about a year. If the
battery pack does not hold a charge for more than 2 hours
after an overnight charge, replace it with a new 2.4-volt, 600
mAh battery pack with a connector that fits the socket in the
battery compartment. You can order a replacement battery
pack through RadioShack. Install the new battery pack and
charge it for about 15–20 hours. If you have trouble
replacing the battery pack, take the phone to your local
RadioShack for assistance.
o
n
5'66+0)"6*'"4+0)'4"610'
You can select either a high or low ringer tone setting on the
handset while the phone is not in use. Lift the handset and
press VOL/RING to hear the current ringer setting. Repeat-
edly press VOL/RING to select the desired ringer setting.
5'66+0)"6*'"&+#.+0)"/1&'
Your phone is set for tone dialing. If you have pulse service,
change the dialing mode. If you are not sure which type of
service you have, do this test.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Lift the handset and listen for a dial tone.
±"016'"±"
2. Press any number other than 0.±
Setting the Dialing Mode
If the dial tone stops, you have touch-tone service. If the dial
tone continues, you have pulse service.
•
If your phone system requires
that you dial an access code (9,
for example) before you dial an
outside number, do not dial the
access code.
To set the dialing mode, hold down FLASH until the phone
beeps and TALK/BATT flashes, then press # to set the phone
to pulse mode or TONE/∗ to set the phone to tone mode.
•
•
The phone exits setting mode if
a call or page is received, or if
12'4#6+10
you press
.
END
If the battery power becomes
too low, the dialing mode might
reset to tone. If you are on a
pulse line and cannot make a
call, try setting the dialing mode
to pulse.
/#-+0)"#0&"4'%'+8+0)"%#..5
To make a call, lift the handset and press TALK. To answer a
call, simply lift the handset. Or, if the handset is not in place
on the base, press TALK or any number key, #, or ∗. The
TALK/BATT indicator on the handset and the CHARGE/IN
USE indicator on the base light.
Making and Receiving Calls
If the handset is too far from the
base while the phone is in use,
To end a call, place the handset on the base or press END.
The TALK/BATT and CHARGE/IN USE indicators turn off. ±
pressing
might not disconnect
END
the phone. Hang up the handset on
the base.
5'.'%6+0)"6*'"%*#00'.
The phone scans 20 channels (frequency pairs used be-
tween the base and the handset) and automatically selects
a clear channel each time you make or receive a call.
Selecting the Channel
If the handset is too far from the
base, an error tone sounds and the
channel might not change. Move
closer to the base.
If you hear other conversations or you experience difficulty
hearing the conversation, press CHANNEL to select a
different channel. TALK/BATT flashes and the handset
beeps, followed by a brief pause as your phone searches
for a clear channel. ±
Using Redial
•
The redial memory holds up to
24 digits, so you can redial long-
distance as well as local
numbers.
#&,756+0)"6*'"*#0&5'6N5"81.7/'
To adjust the volume of the sound you hear through the
handset during a call, repeatedly press VOL/RING.
•
•
The redial memory also holds
pause entries (see “Entering a
Pause” on Page 9).
75+0)"4'&+#.
The redial memory does not
store a flash entry or any digits
You can quickly dial the last number you dialed. Lift the
handset and press PAUSE/REDIAL when you hear a dial
tone. ±
ino
you press before
(see
FLASH
“Using Flash” on Page 7).
preat
O
Using Flash
If you do not have any special
phone services, pressing
75+0)"(.#5*
FLASH performs the electronic equivalent of a switchhook
operation for special services, such as Call Waiting. For
example, if you have Call Waiting, press FLASH to answer
an incoming call without disconnecting the current call.
Press FLASH again to return to the first call. ±ý
FLASH
might disconnect the current call.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
75+0)"610'"5'48+%'5"10"#"27.5'".+0'
Some special services require tone signals (such as bank-
by-phone). If you have pulse dialing, you can still use these
special tone services.
1. Dial the service’s main number. When the service
answers, press TONE/∗. Any additional numbers you
dial are sent as tone signals. The phone’s dial mode
resets to pulse when you make or receive a call.
2. After you complete the call, return the handset to the
base or press END. The phone automatically resets to
the pulse mode.
2#)+0)
To send a page from the base to the handset or to locate
the handset when the phone is not in use, press PAGE on
the base. The handset beeps for about 1 minute. To stop
the page, press any key on the handset, place the handset
on the base, or press PAGE on the base again.
75+0)"#"*'#&5'6
You can make or answer calls with hands-free convenience
3
32
using an optional headset that has a / -inch (2.5-mm) plug.
Your local RadioShack store has a variety of headsets
available.
To connect the headset, gently flip open the rubber headset
jack cover on the side of the handset, then insert the
headset’s plug into the jack. ±
±"016'"±"
•
•
If you place the handset on the
base to recharge it while the
headset is connected, be sure
the handset seats properly.
With a headset connected, you can make or answer calls as
usual using the keys on the handset.
When you finish using the headset, disconnect it from the
handset and close the rubber cover to protect the jack.
You can use a handset holder
(available from RadioShack) to
hang the handset on your belt
for greater convenience when
using a headset.
/'/14;"&+#.+0)
You can store up to 10 phone numbers in memory, then dial a
stored number by entering its memory location number. You
can also dial a number stored in memory location number 1 by
pressing SPEED DIAL. Each number can be up to 16 digits.
O
•
•
Connecting a headset
disconnects the handset’s
earpiece and microphone.
perat
ion
on the handset also
VOL/RING
controls the headset’s volume.
5614+0)"#"07/$'4"+0"/'/14;
1. Lift the handset.
2. Press MEM. TALK/BATT blinks.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Enter the number and any tone and pause entries (see
“Using Tone Services on a Pulse Line” on Page 8 and
“Entering a Pause” on Page 9). ±
±"016'"±"
Storing a Number in Memory
4. Press MEM again, then enter the memory location
number (0–9) where you want to store the number. A
tone sounds to indicate that the number is stored.
•
An error tone sounds and the
phone exits the programming
mode if you wait more than 20
seconds between keypresses.
To replace a stored number, simply store a new one in its
place. Or, lift the handset and press MEM twice. Then press
the memory location number (0–9) you want to clear. A tone
sounds.
•
•
Each tone or pause entry uses
one digit of memory.
If you try to enter more than 16
digits, the phone beeps 5 times
and exits the programming
mode. Start over at Step 2 and
enter no more than 16 digits in
Step 3.
'06'4+0)"#"2#75'
In some telephone systems, you must dial an access code
(9, for example) and wait for a second dial tone before you
can dial an outside number. You can store the access code
with the phone number. However, you should also store a
pause after the access code to allow the outside line time to
connect. To enter a 2-second pause, press PAUSE/REDIAL.
You can add more pause entries for a longer pause.
Dialing a Memory Number
If you select an empty memory
location, the phone beeps 5 times.
&+#.+0)"#"/'/14;"07/$'4
To dial a number stored in memory, lift the handset and
press TALK. TALK/BATT lights. When you hear a dial tone,
press MEM and enter the memory location number for the
number you want to dial.
To dial a number stored in memory location 1, press SPEED
DIAL. You do not have to press TALK when you press
SPEED DIAL. ±
%*#+0/&+#.+0)"5'48+%'"07/$'45
For quick recall of numbers for special services (such as
bank-by-phone), store each group of numbers in its own
memory location.
Dial the service’s main number first. Then, when prompted
to enter the number, press MEM and enter the number for
the location where the additional information is stored.
ino
6'56+0)"5614'&"'/'4)'0%;"07/$'45
If you store an emergency service’s number (police
department, fire department, ambulance) and you choose to
test the stored number, make the test call during the late
evening or early morning hours to avoid peak demand
periods. Also, remain on the line to explain the reason for
your call.
preat
O
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6417$.'5*116+0)
T
r
2TQDNGO"
5WIIGUVKQPU
ubleshot
Low volume or
unusual sounds.
Someone has picked up another phone on
the same line. Hang up the other phone.
If you are using the headset, make sure
the headset’s plug is properly connected to
the jack.
ing
Severe noise inter-
ference.
Keep the handset away from computers,
remote control toys, wireless microphones,
alarm systems, intercoms, room monitors,
fluorescent lights, and electrical appli-
ances.
Move to another location or turn off the
source of interference.
Press
to change the channel.
CHANNEL
Hang up and redial the number.
Be sure the base’s phone line cord and AC
adapter are correctly and securely
connected.
The phone does not
work properly.
Be sure the battery pack in the handset is
connected and charged.
Return the handset to the base to reset the
security access-protection code.
The handset stops
working or works
poorly during a call.
Move the handset closer to the base.
Be sure the handset’s battery pack is
charged.
The handset’s range Be sure the handset’s and base’s antenna
has decreased and is not touching a metal surface.
the phone cannot be
operated at a useful
distance from the
base because the
signal becomes
weak or noisy.
The handset battery Check the charging contacts on the hand-
pack does not
charge.
set and base. If they are dirty, clean them
with a pencil eraser.
Be sure the battery pack is connected cor-
rectly.
Be sure the handset is properly seated on
the base.
The handset does
not ring or receive a
page.
Move the handset closer to the base.
Return the handset to the base to recharge
the battery pack.
Move the base away from other electrical
devices.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
If you still have problems, disconnect the phone. If other
phones on the same line work properly, the fault is in this
phone or its installation. If you cannot find the problem, take
the phone to your local RadioShack store for assistance.
%#4'
Keep the phone dry; if it gets wet, wipe it dry immediately.
Use and store the phone only in normal temperature
environments. Handle the phone carefully; do not drop it.
Keep the phone away from dust and dirt, and wipe it with a
damp cloth occasionally to keep it looking new.
5'48+%'"#0&"4'2#+4
If your phone is not performing as it should, take it to your
local RadioShack store for assistance. Modifying or
tampering with the phone’s internal components can cause
a malfunction and might invalidate its warranty and void
your FCC authorization to operate it.
Crae
+/2146#06"+0(14/#6+10
This telephone has been tested and found to comply with all
applicable UL and FCC standards.
(%%"56#6'/'06
Your phone complies with Part 68 of FCC Rules. You must,
upon request, provide the FCC registration number and the
REN to your telephone company. Both numbers are on the
bottom of your phone.
We have designed your phone to conform to federal regula-
tions, and you can connect it to most telephone lines. How-
ever, each phone (and each device, such as a telephone or
answering machine) that you connect to the telephone line
draws power from the telephone line. We refer to this power
draw as the device's ringer equivalence number, or REN on
the bottom of your phone.±
±"016'"±"
You must not connect your phone
to:
If you use more than one phone or other device on the line,
add up all of the RENs. If the total is more than five (three in
rural areas), your telephones might not ring. If ringer
operation is impaired, remove a device from the line.
•
•
•
coin-operated systems
party-line systems
In the unlikely event that your phone causes problems on
the phone line, the phone company can temporarily
discontinue your service. If this happens, the phone
company attempts to notify you in advance. If advance
most electronic key phone
systems
11
Download from Www.Somanuals.com. All Manuals Search And Download.
notice is not practical, the phone company notifies you as
soon as possible and advises you of your right to file a
complaint with the FCC.
Limited One-Year Warranty
This product is warranted by RadioShack against man-
ufacturing defects in material and workmanship under
normal use for one (1) year from the date of purchase
from RadioShack company-owned stores and autho-
rized RadioShack franchisees and dealers. EXCEPT
AS PROVIDED HEREIN, RadioShack MAKES NO EX-
PRESS WARRANTIES AND ANY IMPLIED WARRAN-
TIES, INCLUDING THOSE OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO THE DURATION OF THE
WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN,
RadioShack SHALL HAVE NO LIABILITY OR RE-
SPONSIBILITY TO CUSTOMER OR ANY OTHER
PERSON OR ENTITY WITH RESPECT TO ANY LIA-
BILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR
INDIRECTLY BY USE OR PERFORMANCE OF THE
PRODUCT OR ARISING OUT OF ANY BREACH OF
THIS WARRANTY, INCLUDING, BUT NOT LIMITED
TO, ANY DAMAGES RESULTING FROM INCONVE-
NIENCE, LOSS OF TIME, DATA, PROPERTY, REVE-
NUE, OR PROFIT OR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
EVEN IF RadioShack HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Also, the phone company can make changes to its lines,
equipment, operations, or procedures that could affect the
operation of this telephone. The telephone company notifies
you of these changes in advance, so you can take the
necessary steps to prevent interruption of your telephone
service.
.+)*60+0)
Your telephone has built-in protection circuits to reduce the
risk of damage from surges in telephone line and power line
current. These protection circuits meet or exceed the FCC
requirements. However, lightning striking the telephone or
power lines can damage your telephone.
Some states do not allow limitations on how long an im-
plied warranty lasts or the exclusion or limitation of inci-
dental or consequential damages, so the above
limitations or exclusions may not apply to you.
In the event of a product defect during the warranty pe-
riod, take the product and the RadioShack sales receipt
as proof of purchase date to any RadioShack store.
RadioShack will, at its option, unless otherwise provided
by law: (a) correct the defect by product repair without
charge for parts and labor; (b) replace the product with
one of the same or similar design; or (c) refund the pur-
chase price. All replaced parts and products, and prod-
ucts on which a refund is made, become the property of
RadioShack. New or reconditioned parts and products
may be used in the performance of warranty service.
Repaired or replaced parts and products are warranted
for the remainder of the original warranty period. You will
be charged for repair or replacement of the product
made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure
caused by or attributable to acts of God, abuse, acci-
dent, misuse, improper or abnormal usage, failure to fol-
low instructions, improper installation or maintenance,
alteration, lightning or other incidence of excess voltage
or current; (b) any repairs other than those provided by
a RadioShack Authorized Service Facility; (c) consum-
ables such as fuses or batteries; (d) cosmetic damage;
(e) transportation, shipping or insurance costs; or (f)
costs of product removal, installation, set-up service ad-
justment or reinstallation.
Lightning damage is not common. Nevertheless, if you live
in an area that has severe electrical storms, we suggest that
you unplug your phone when storms approach to reduce the
possibility of damage.
This warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state.
RadioShack Customer Relations,
200 Taylor Street, 6th Floor, Fort Worth, TX 76102
12/99
43-3533/3534/3541/3542/3543
UCZZ01367ZZ
RadioShack Corporation
Fort Worth, Texas 76102
06A02
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|