43-3911
preparing your phone
choosing your settings
20-Number Memory
Speakerphone
Your phone’s display is protected by a plastic label
during shipping. Peel off the label before using your
phone.
After you install your batteries, system information
5. Repeat Step 4 to store the minute, month and date.
To reset the language, contrast, area code and
time/date settings:
appears in the display, followed by E for English, F for
French and S for Spanish.
1. Repeatedly press REVIEW or to select the
desired display language and press DELETE to
store it. If you do not select a language within a few
seconds, the system defaults to English.
Thank you for purchasing your 20-Number Memory
Speakerphone from RadioShack. It combines a
speakerphone and a Caller ID unit in one system. It
shows the caller’s telephone number (and name, if
available in your area), and the date and time of each
call, as provided by your local telephone company to
Caller ID service subscribers.
installing batteries
1. Hold down DELETE and press . LCD CONTRAST
Insert three AAA alkaline
batteries (not supplied).
displays.
2. Repeat Step 1 above to reset each setting.
When
appears or the
2. When LCD CONTRAST appears in the display, repeat
display becomes dim,
replace the batteries.
step 1 to select one of the six settings.
3. When 000 SET AREA CODE displays and the 0
flashes, repeatedly press REVIEW or until the
first digit of your area code appears. Press DELETE
to store it. Repeat for each digit of your area code.
battery notes:
REVIEW /
Scroll up or down
to set the desired
language, LCD
contrast, area code,
and time/date.
Also lets you scroll
through all numbers
• When replacing batteries, be
what’s included
sure to put in new batteries
within one minute of removing the old ones. If not, your
time and date will be lost.
NOTE: If you do not press a button, the system automatically
sets the area code to 000.
20-Number Memory Speakerphone
Stand
• Use only fresh batteries of the required size and
recommended type.
• Do not mix batteries of different sizes or chemistries.
• Always remove old or weak batteries. Batteries can leak
chemicals that can damage electronic parts.
in your Caller ID
memory.
4. Press REVIEW or to set the hour, and press
Index Card
Long Modular Cord
Coiled Handset Cord
3 Index Cards
Short Modular Cord
Mounting Bracket
User’s Guide
Flip open the clear cover
DELETE to store it.
and use the supplied index
card inside to record the
stored numbers.
NOTE: If you do not press a key, the system automatically
sets the time to 12:00 PM 1/01.
VOL-/VOL+ – controls the
CALL BACK – dial
a phone number in
the Caller ID record.
MEM – stores a
phone downward to secure it.
6. Use a coin to turn the handset hook 180°.
mounting and connecting the phone
volume of the sound through
number in an indirect
memory location (0-9).
1. Press and pull out the stand from the base.
your handset and speakerphone.
2. Connect the handset to your phone using the coiled
handset cord, and then fit the cable in the groove as
shown below.
3. Align the mounting bracket’s round tabs with the holes
on the base, then slide the mounting bracket upward to
snap it into place.
Handset Hook
• Your telephone connects directly to a modular phone
line jack. If your phone line jack is not a modular jack,
you can update the wiring yourself using adapters and
jacks from your local RadioShack store. Or, call your
telephone company to update the wiring for you.
SPEAKER – press
to switch between
the handset and
speakerphone
M1-M10 – store 10
numbers and dial them
with the touch of a
button.
4. Connect one end of the short modular cord into LINE,
and the other end to the wall plate jack.
• The USOC number of the jack to be installed is RJ11C.
5. Fit the keyhole slots over the wall plate studs. Slide the
for convenient
hands-free use.
When a headset
is conneted, press
SPEAKER to make
or answer calls. To
end a call, press
SPEAKER again.
OPT/P (Option/
Pause) – press to
select different dialing
options based on
the number you are
calling.
Use the stand to place
your phone on a desk.
Mounting Bracket
LINE
RINGER VOLUME HI/
LOW/OFF
Set ringer’s volume to
HI or LOW as desired.
Set to OFF for no sound.
STORE – press to
store numbers in
memory locations. See
“Memory Dialing”.
HEADSET
For hands-free
conversation when
the phone is placed
on the desk, connect
an optional headset
HOLD – press to
REDIAL
MUTE – press to keep
the other party from
hearing you. To resume
the conversation,
MODE T/P/TB
See “setting the dialing
mode”.
put a call on hold.
To resume the call,
press the switchhook
or lift the handset.
– press to
redial the last
number you
dialed.
FLASH – press to
answer another call if
you have Call Waiting.
with a 3/ -inch
32
release MUTE.
(2.5mm) plug into
the HEADSET jack.
RINGER R1/R2
Set to R1 for a high number of rings
or R2 for a lower number of rings.
Please read this user’s guide before
installing, setting up and using your new product
Coiled Handset Cord
Download from Www.Somanuals.com. All Manuals Search And Download.
|