21-1649.fm Page 1 Thursday, August 5, 1999 11:33 AM
OWNER’S MANUAL
Cat. No. 21-1649
TRC-236
40-Channel 5-Watt
CB Walkie Talkie
with LED Display
Please read before using this equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 3 Thursday, August 5, 1999 11:33 AM
Power/Charging Jack — lets you power
your TRC-236 from an AC or DC power
source, so you can use the TRC-236 with-
out draining the batteries. And, lets you
charge nickel-cadmium batteries without
removing them from the TRC-236.
Note: To power your TRC-236 with inter-
nal batteries, you need eight AA alkaline
batteries or ten nickel-cadmium recharge-
able batteries (not supplied).
We recommend you record the TRC-
236’s serial number here. The serial
number is located on the walkie talkie’s
back panel:
3
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 4 Thursday, August 5, 1999 11:33 AM
FCC INFORMATION
The Federal Communications Commis-
sion (FCC) does not require you to have
a license to operate this walkie talkie.
However, the FCC does require that you
read and know Part 95 of FCC Rules.
These rules apply to the operation of a
Class D CB. We have provided a copy of
these regulations with your TRC-236.
Internal adjustments and/or modifications
can lead to illegal operation as defined by
Part 95 of FCC Rules. Such illegal opera-
tion can lead to very serious consequenc-
es.
To be safe and sure:
•
•
Never open your TRC-236’s case.
Never modify your TRC-236.
Your TRC-236 might cause TV or radio
interference even when it is operating
properly. To determine whether your
TRC-236 is causing the interference, turn
off your TRC-236. If the interference goes
away, your TRC-236 is causing it. Try to
eliminate the interference by:
•
Moving your TRC-236 away from the
TV or radio
•
Contacting your local RadioShack
store for help
Warning: Do not open your TRC-236 to
make any internal adjustments. Any inter-
nal adjustments should be made only by
authorized service personnel.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 5 Thursday, August 5, 1999 11:33 AM
CONTENTS
Powering the CB ................................ 6
Using the POWER Jack and
ALKALINE/NI-CD Switch .................. 6
Using Batteries ................................. 7
Testing the Battery Power .......... 10
Recharging Nickel-Cadmium
Batteries ..................................... 10
Using Vehicle Battery Power........... 12
Using AC Power ............................. 13
Connecting an Optional Antenna .... 15
Operation .......................................... 18
Receiving Transmissions and
Adjusting Squelch .......................... 18
Transmitting .................................... 20
CB Operation Tips ........................... 22
Common Uses for a CB Radio ....... 22
Business Uses ........................... 22
Personal Uses ........................... 22
Using Common 10-Codes .............. 23
CB Courtesy ................................... 25
Maximum Range ............................ 25
Troubleshooting ............................... 26
Maintenance ..................................... 27
Specifications .................................. 28
5
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 6 Thursday, August 5, 1999 11:33 AM
POWERING THE CB
You can power your TRC-236 from any of
these sources (none supplied):
• Eight AA alkaline batteries with the
two supplied dummy batteries
• Ten rechargeable AA nickel-
cadmium batteries
• 12-volt vehicle battery power using a
fused power cord
• Standard AC power using a power
supply
USING THE POWER JACK
AND ALKALINE/NI-CD
SWITCH
POWER
The
jack lets you connect an ex-
ternal power source (such as your vehi-
cle’s battery power or AC power), or
connect a battery charger to charge
nickel-cadmium batteries while they are in
the TRC-236.
AL-
The TRC-236 also has a slide switch (
KALINE/NI CD
-
) inside the battery com-
partment that you must set correctly,
depending on what power source you are
using and whether or not you want to
charge rechargeable batteries while they
are in the TRC-236.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 7 Thursday, August 5, 1999 11:33 AM
• Set it to ALKALINE before you con-
nect an external power source (vehi-
cle battery power or AC adapter) to
the POWER jack or while you are us-
ing internal batteries (alkaline or re-
chargeable).
• Set it to NI-CD only when you con-
nect a battery charger to the POWER
jack to charge the installed recharge-
able batteries.
Warning: To avoid injuring yourself or
damaging the TRC-236, connect a bat-
tery charger to the POWER jack only
when nickel-cadmium batteries are in-
stalled (see “Recharging Nickel-Cadmium
Batteries” on Page 10). Never try to re-
charge non-rechargeable batteries. They
could get very hot and explode.
Note: You can connect an external pow-
er source for power regardless of the type
of batteries you installed.
USING BATTERIES
You can power the TRC-236 from eight
AA alkaline batteries (such as Ra-
dioShack Cat. No. 23-552) with the two
supplied dummy batteries, or 10 re-
chargeable AA nickel-cadmium batteries
(such as Cat. No. 23-125).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 8 Thursday, August 5, 1999 11:33 AM
Cautions:
• Always use fresh, or freshly charged,
batteries of the required size and
recommended type.
• Do not mix old and new batteries,
different types of batteries (stan-
dard, alkaline, or rechargeable
nickel-cadmium), or rechargeable
batteries of different capacities.
Follow these steps to install the batteries.
1. If the TRC-236 is on, turn OFF/VOLUME
fully counterclockwise until it clicks to
turn it off.
2. Slide the strap on the back of the
TRC-236 through the buckle and the
battery compartment cover to re-
move it.
3. Slide the battery compartment cover
in the direction of the arrows to
remove it.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 9 Thursday, August 5, 1999 11:33 AM
4. Be sure ALKALINE/NI-CD inside the
battery compartment is set to ALKA-
LINE.
5. Put eight AA alkaline batteries and
the two supplied dummy batteries, or
ten AA nickel-cadmium batteries into
the battery compartment, as indi-
cated by the polarity symbols (+ and
–) marked inside.
Note: Before you use the TRC-236
with nickel-cadmium batteries, you
need to charge the batteries (see
“Recharging Nickel-Cadmium Batter-
ies” on Page 10).
6. Slide the strap on the back of the
TRC-236 through the battery com-
partment cover to reattach it.
7. Replace the battery compartment
cover.
Cautions:
• If you will not be powering the TRC-
236 from internal batteries for sev-
eral months, remove the batteries.
• Dispose of old batteries promptly
and properly.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 10 Thursday, August 5, 1999 11:33 AM
Testing the Battery Power
1. Turn on the TRC-236 by rotating
OFF/VOLUME clockwise until it clicks.
2. Hold down BATT TEST. If the indica-
tor lights, there is enough battery
power to operate the CB. If the indi-
cator is dim or does not light, replace
or recharge the batteries.
Recharging Nickel-Cadmium
Batteries
You can use a battery charger, Cat. No.
23-249 (not supplied), to charge or re-
charge nickel-cadmium batteries while
they are inside the TRC-236’s battery
compartment.
Do not use the TRC-236 while you are
charging the nickel-cadmium batteries.
Cautions:
• Use only the recommended battery
charger to recharge the batteries in
the TRC-236. Other chargers could
damage your TRC-236 or the batter-
ies.
• Be careful not to overcharge nickel-
cadmium batteries.
• To prevent damage to rechargeable
nickel-cadmium batteries, never
charge them in an area where the
temperature is above 90°F (32°C) or
below 40°F (4.5°C).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 11 Thursday, August 5, 1999 11:33 AM
Follow these steps to charge nickel-
cadmium batteries in the TRC-236.
1. If the TRC-236 is on, turn OFF/VOLUME
fully counterclockwise until it clicks to
turn it off.
2. Set ALKALINE/NI-CD inside the bat-
tery compartment to NI-CD (see “Us-
ing the Power Jack and Alkaline/NI-
CD Switch” on Page 6).
3. Connect the battery charger’s 5.5
mm outer diameter/2.1 mm inner
diameter barrel plug to the POWER
jack on the side of the TRC-236,
then plug the battery charger’s plug
into a standard AC outlet.
It takes about 24 hours to charge
new or fully discharged nickel-
cadmium batteries. Subsequent
charges take about 16 to 18 hours.
4. When charging is complete, unplug
the battery charger’s plug from the
AC outlet. Then disconnect the bat-
tery charger’s barrel plug from the
POWER jack.
5. If the TRC-236 is on, turn OFF/VOLUME
fully counterclockwise until it clicks to
turn it off. Then set ALKALINE/NI-CD
to ALKALINE.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 12 Thursday, August 5, 1999 11:33 AM
Note: You can use an external charger
(such as Cat. No. 23-134, not sup-
plied) to recharge the nickel-cadmium
batteries. After removing the batteries
from the TRC-236, follow the instructions
that come with the external charger.
Important: Your TRC-236 is capable of
using nickel-cadmium batteries. At the end
of the batteries’ useful life, they must be re-
cycled or disposed of properly. Contact
your local, county, or state hazardous
waste management authorities for informa-
tion on recycling or disposal programs in
your area. Some options that might be
available are: municipal curbside collec-
tion, drop-off boxes at retailers such as
your local RadioShack store, recycling col-
lection centers, and mail-back programs.
USING VEHICLE BATTERY
POWER
You can power your TRC-236 from your
vehicle’s cigarette-lighter socket with an
optional 12-volt DC fused power cord
(such as Cat. No. 270-1533).
Cautions:
• You must use a DC fused cord that
supplies 12 volts and delivers at
least 1200 milliamps of vehicle
power. Its center tip must be set to
positive, and its plug must correctly
fit the TRC-236’s POWER jack. The
recommended fused cord meets
these specifications. Using a fused
cord that does not meet these speci-
fications could damage the TRC-236
or the fused cord.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 13 Thursday, August 5, 1999 11:33 AM
• When you finish using the TRC-236,
unplug the fused cord from the ciga-
rette-lighter socket before you dis-
connect it from your TRC-236.
1. If the TRC-236 is on, turn OFF/VOL-
UME fully counterclockwise until it
clicks to turn it off.
2. Be sure ALKALINE/NI-CD inside the
battery compartment is set to ALKA-
LINE.
3. Insert the power cord’s 5.5 mm outer
diameter/2.1 mm inner diameter bar-
rel plug into the POWER jack.
4. Plug the power cord’s other end into
your vehicle’s cigarette-lighter socket.
Note: If the TRC-236 does not operate
when you use the DC power cord, unplug
the cord from the cigarette-lighter socket
and clean any ashes or debris from the
socket. If your TRC-236 still does not
work, check the fuse in the DC power cord
and replace it if necessary.
USING AC POWER
You can power your TRC-236 from stan-
dard AC power using an optional AC-to-
12 V DC power supply (such as Cat. No.
22-504) and an optional DC fused power
cord (such as Cat. No. 270-1533).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 14 Thursday, August 5, 1999 11:33 AM
Cautions:
• The power supply must be able to
deliver 12 volts and at least 1200 mil-
liamps of power. The recommended
power supply meets these specifica-
tions. Using a power supply that
does not meet these specifications
could damage the TRC-236 or the
power supply.
• You must use a DC fused cord that
supplies 12 volts and delivers at
least 1200 milliamps of power. Its
center tip must be set to positive,
and its barrel plug must correctly fit
the TRC-236’s POWER jack. The rec-
ommended fused cord meets these
specifications. Using a fused cord
that does not meet these specifica-
tions could damage the TRC-236 or
the fused cord.
• To help prevent an electrical short,
unplug the DC fused cord’s plug from
the AC adapter’s power socket be-
fore you unplug the cord’s barrel plug
from the TRC-236.
Follow these steps to connect the TRC-
236 to AC power.
1. If the TRC-236 is on, turn OFF/VOL-
UME fully counterclockwise until it
clicks to turn it off.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 15 Thursday, August 5, 1999 11:33 AM
2. Connect the DC fused cord’s 5.5 mm
outer diameter/2.1 mm inner diame-
ter barrel plug to the TRC-236’s
POWER jack.
3. Be sure ALKALINE/NI-CD inside the
battery compartment is set to ALKA-
LINE.
4. Plug the DC fused cord’s other end
into the power supply’s power socket.
5. Plug the power supply into a stan-
dard AC outlet, then turn on the pow-
er supply.
Note: If the TRC-236 does not operate
when you use the DC fused cord, turn the
power supply off, unplug the cord from the
power supply’s power socket, then clean
any debris from the socket. If your TRC-
236 still does not work, check the fuse in
the DC fused cord and replace it if neces-
sary.
CONNECTING AN
OPTIONAL ANTENNA
Your walkie talkie comes with a telescop-
ing antenna that is ideal for most applica-
tions. However, the walkie talkie’s EXT
ANTENNA jack makes it easy to connect
other types of antennas, too. For mobile
or base station use, you might want to
connect an optional external antenna.
Your local RadioShack store carries a
wide selection of external mobile or out-
door base-station antennas. Choose the
one that best meets your needs.
When deciding on a mobile or base-
station antenna and its location, consider
the following:
• The location of the antenna should
be as high as possible.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 16 Thursday, August 5, 1999 11:33 AM
• The antenna and antenna cable
should be as far as possible from
sources of electrical noise (appli-
ances, other radios, and so on).
• The antenna should be vertical for
the best performance.
Note: When connecting an optional an-
tenna, always use 50-ohm coaxial cable,
such as RG-58 or RG-8. For lengths over
50 feet, use RG-8 low-loss dielectric coax-
ial cable. If the coaxial cable’s connector
does not fit into the EXT ANTENNA jack,
you might also need a PL-259-to-phono
antenna plug adapter, such as Cat. No.
278-208. Your local RadioShack store car-
ries a wide variety of coaxial antenna ca-
ble and connectors.
Follow the installation instructions sup-
plied with the antenna, route the antenna
cable to the TRC-236, then connect it to
the EXT ANTENNA jack.
Cautions:
• Do not run the cable over sharp
edges or moving parts.
• Do not run the cable next to power
cables or other CB antenna cables.
• Do not run the cable through a vehi-
cle’s engine compartment or other
areas that produce extreme heat.
• Follow all cautions and warnings
included with the antenna.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 17 Thursday, August 5, 1999 11:33 AM
Warning: When installing or removing a
base station CB antenna, use extreme
caution. If the antenna starts to fall, let it
go! It could contact overhead power lines.
If the antenna touches the power line,
contact with the antenna, mast, cable or
guy wires can cause electrocution and
death! Call the power company to remove
the antenna. DO NOT attempt to do so
yourself.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 18 Thursday, August 5, 1999 11:33 AM
OPERATION
Before you use your TRC-236, we recom-
mend you read “CB Operation Tips” on
Page 22, which contains information to
help you use it effectively and courteously.
RECEIVING
TRANSMISSIONS AND
ADJUSTING SQUELCH
1. If you did not connect an external
antenna, fully extend the TRC-236’s
telescoping antenna and hold the
TRC-236 so the antenna is vertical.
Caution:
Unless an external an-
tenna is attached, if you do not fully
extend the antenna, the TRC-236’s
efficiency is reduced.
OFF/
2. Turn on the TRC-236 by turning
VOLUME
clockwise until you hear a
click and a hissing sound.
Note:
When you tune a channel, the
channel’s number appears or flashes
on the display for several seconds
then fades, to save battery power. To
continuously display the channel
DISPLAY
number, press and hold
the side of the TRC-236.
on
18
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 19 Thursday, August 5, 1999 11:33 AM
To redisplay the channel number for
several seconds, simply press and
release DISPLAY.
3. Repeatedly press CH s to select
higher channels, or CH t to select
lower channels. To move rapidly
through the channels, hold down CH
s or t.
4. Adjust OFF/VOLUME to a comfortable
listening level.
5. Adjust SQUELCH to cut out the back-
ground noise. Wait until there is no
signal on the channel, then slowly
turn SQUELCH clockwise until the
background noise stops.
Note: Do not turn SQUELCH too far
clockwise because you might also
cut out weak signals.
6. To turn off the TRC-236, turn OFF/
VOLUME toward OFF until it clicks.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 20 Thursday, August 5, 1999 11:33 AM
TRANSMITTING
1. Follow Steps 1–5 in “Receiving
Transmissions
and
Adjusting
Squelch” on Page 18.
2. To increase the transmitted signal
strength and increase the TRC-236’s
range, set POWER HI/LO on the side
of the TRC-236 to HI.
To decrease the transmitted signal
strength and save battery power, set
POWER HI/LO to LO.
3. Hold the TRC-236 2 to 3 inches from
your mouth. Hold down PUSH TO
TALK on the side of the TRC-236
and speak in a normal voice into the
microphone.
Micro-
phone
When you finish speaking, release
PUSH TO TALK.
Note: Do not speak too loudly when
transmitting. It does not make your
signal any stronger, and might distort
your transmission.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 21 Thursday, August 5, 1999 11:33 AM
Important: Channel 9 is reserved for
motorist assistance and for reporting
emergency information about acci-
dents, hazardous road conditions,
and so on. If you are using Channel
9, always give emergency messages
priority.
4. To turn off the TRC-236, turn OFF/
VOLUME toward OFF until it clicks.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 22 Thursday, August 5, 1999 11:33 AM
CB OPERATION TIPS
The following tips will help you get the
most enjoyment from your TRC-236.
COMMON USES FOR A CB
RADIO
Business Uses
•
•
•
Truck drivers and delivery personnel
can learn road and traffic conditions
and get assistance in locating desti-
nations. A walkie talkie is also good
company on those “long hauls.”
On construction crews, a walkie
talkie quickly pays for itself when you
are calling for additional materials or
coordinating the activities of differ-
ent work crews.
For security officers, a walkie talkie is
more than a convenience — it is a
must for both safety and efficiency.
Personal Uses
•
Keep in touch with home while driv-
ing to work, to the store, or to a
social activity. Let your family know
you are tied up in traffic or that you
will stop by the store on the way
home.
•
If you are a two-car (or more) family,
walkie talkies are great for communi-
cating with family members while
they are in their cars.
•
•
Contact friends or neighbors — find
out “what’s happening” or plan a get-
together.
Ever have car trouble or run out of
gas on the highway? What an assur-
ance it is to be able to radio for assis-
tance.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 23 Thursday, August 5, 1999 11:33 AM
•
Camping, fishing, and other sports
are more fun with a walkie talkie.
Locate a friend or find out “what’s
cooking” back at camp.
USING COMMON
10-CODES
Citizen’s band operators have largely
adopted the 10-codes for standard ques-
tions and answers. Their use permits fast-
er communication and better intelligibility
in noisy areas.
This table lists the codes adopted by the
Associated Public Safety Communica-
tions Officers (APCO).
Code
Meaning
10-1
Cannot understand your mes-
sage.
10-2
10-3
10-4
Your signal is good.
Stop transmitting.
Message received and under-
stood.
10-5
10-6
Relay information to _________.
I am busy.
10-7
Out of service.
10-8
In service.
10-9
Repeat last message.
Negative (No).
10-10
10-11
10-12
10-13
10-14
_____________ in service.
Stand by.
Report ___________ conditions.
Information.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 24 Thursday, August 5, 1999 11:33 AM
Code
Meaning
10-15
10-16
10-17
10-18
10-19
10-20
10-21
10-22
10-23
10-24
10-26
10-30
10-31
10-33
Message delivered.
Reply to message.
En route.
Urgent.
Contact __________.
My location is __________.
Call ________ by telephone.
Cancel last message.
Arrived at the scene.
Assignment complete.
Estimated time of arrival is ____.
Use caution.
Pick up.
Emergency traffic. Clear the
channel.
10-34
The time is _____.
Note: Although this table lists the 10-
codes’ meanings in the form of a state-
ment, they can also be phrased as ques-
tions (10-6: Are you busy?, 10-20: What is
your location?).
24
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 25 Thursday, August 5, 1999 11:33 AM
CB COURTESY
•
Wait for a pause in someone else’s
transmission before you ask for a
break.
•
If you do not receive an answer to
your call after a second attempt, sign
off and wait several minutes before
trying again.
•
•
Do not hold down PUSH TO TALK
when you are not talking. (This is
called dead keying.)
Assist callers with directions, infor-
mation about road conditions, and
any other reasonable requests.
MAXIMUM RANGE
The maximum range and quality of CB
transmissions vary depending on these
conditions:
•
•
Amount of power in the batteries
The surrounding terrain — moun-
tains and tall buildings limit the range
•
•
Weather conditions
The number of nearby CBs operating
on the same channel
To ensure maximum range, always keep
fresh alkaline batteries or fully charged
nickel-cadmium batteries in your TRC-
236 when using battery power.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 26 Thursday, August 5, 1999 11:33 AM
TROUBLESHOOTING
If your TRC-236 is not working as it
should, follow these suggestions to see if
you can eliminate the problem. If you can-
not, take it to your local RadioShack store
for assistance.
Symptom
Suggestion
Weak, bad,
or no recep-
tion.
Ensure the TRC-236
is turned on.
Ensure the volume is
turned up.
Ensure the telescop-
ing antenna is fully
extended or an exter-
nal antenna is
attached to the TRC-
EXT ANTENNA
236’s
jack.
Ensure the batteries
are not weak (see
“Testing the Battery
Power” on Page 10).
Ensure you are not
PUSH TO
pressing
TALK
.
Trouble with
transmis-
sion
Ensure the telescop-
ing antenna is fully
extended or an exter-
nal antenna is
attached to the TRC-
EXT ANTENNA
236’s
jack.
Ensure you are fully
PUSH TO
pressing
TALK
.
Ensure the batteries
are not weak (see
“Testing the Battery
Power” on Page 10).
26
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 27 Thursday, August 5, 1999 11:33 AM
MAINTENANCE
Your RadioShack TRC-236 40-Channel 5-
Watt CB Walkie Talkie with LED Display is
an example of superior design and crafts-
manship. The following suggestions will
help you care for your TRC-236 so you
can enjoy it for years.
Keep the TRC-236 dry. If it
gets wet, wipe it dry immedi-
ately. Liquids might contain
minerals that can corrode
the electronic circuits.
Handle the TRC-236 gently
and carefully. Dropping it
can damage circuit boards
and cases and can cause
the TRC-236 to work im-
properly.
Use and store the TRC-236
only in normal temperature
environments. Temperature
extremes can shorten the
life of electronic devices,
damage batteries, and dis-
tort or melt plastic parts.
Keep the TRC-236 away
from dust and dirt, which
can cause premature wear
of parts.
Wipe the TRC-236 with a
damp cloth occasionally to
keep it looking new. Do not
use harsh chemicals, clean-
ing solvents, or strong deter-
gents to clean the TRC-236.
Modifying or tampering with the TRC-236’s
internal components can cause a malfunc-
tion and might invalidate your TRC-236’s
warranty and void your FCC authorization
to operate it. If your TRC-236 is not per-
forming as it should, take it to your local
RadioShack store for assistance.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 28 Thursday, August 5, 1999 11:33 AM
SPECIFICATIONS
Receiver
Frequency Coverage ... 26.965 27.405 MHz
–
Sensitivity (Max.) ..... 0.5 V at 10 dB (S+N)/N
µ
Adjacent Channel Rejection ................. 45 dB
Squelch ........... Adjustable from 1 V to 1 mV
µ
Audio Output (10% THD) ................. 400 mW
Current Drain ............................... 85 300 mA
–
Transmitter
Frequency Coverage ... 26.965 27.405 MHz
–
Power Input (at 12V DC):
High ................................................. 5 W
Low .................................................. 2 W
Power Output:
High .............................................. 2.5 W
Low ................................................... 1 W
Spurious Emission .............................. –67 dB
Type of Modulation ..................................... A3
Frequency Tolerance .......................... 0.003%
Telescoping Antenna Impedance ............ 50
Ω
Antenna Length ..................................... 47 In.
(119.0 cm)
Current Drain:
High ........................................... 650 mA
Low ............................................. 450 mA
Dimensions (HWD) ................ 71/2 23/4 2 In.
×
×
(190 70 50 mm)
×
×
Weight ................................................ 14.1 oz
(399 g)
Specifications are typical; individual units
might vary. Specifications are subject to
change and improvement without notice.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 29 Thursday, August 5, 1999 11:33 AM
NOTES
29
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 30 Thursday, August 5, 1999 11:33 AM
30
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 31 Thursday, August 5, 1999 11:33 AM
31
Download from Www.Somanuals.com. All Manuals Search And Download.
21-1649.fm Page 32 Thursday, August 5, 1999 11:33 AM
Limited Ninety-Day Warranty
This product is warranted by RadioShack against manu-
facturing defects in material and workmanship under
normal use for ninety (90) days from the date of pur-
chase from RadioShack company-owned stores and au-
thorized RadioShack franchisees and dealers. EXCEPT
AS PROVIDED HEREIN, RadioShack MAKES NO EX-
PRESS WARRANTIES AND ANY IMPLIED WARRAN-
TIES, INCLUDING THOSE OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO THE DURATION OF THE
WRITTEN LIMITED WARRANTIES CONTAINED
HEREIN. EXCEPT AS PROVIDED HEREIN, Ra-
dioShack SHALL HAVE NO LIABILITY OR RESPONSI-
BILITY TO CUSTOMER OR ANY OTHER PERSON OR
ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR
DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY
USE OR PERFORMANCE OF THE PRODUCT OR
ARISING OUT OF ANY BREACH OF THIS WAR-
RANTY, INCLUDING, BUT NOT LIMITED TO, ANY
DAMAGES RESULTING FROM INCONVENIENCE,
LOSS OF TIME, DATA, PROPERTY, REVENUE, OR
PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES, EVEN IF Ra-
dioShack HAS BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES.
Some states do not allow the limitations on how long an
implied warranty lasts or the exclusion of incidental or
consequential damages, so the above limitations or ex-
clusions may not apply to you.
In the event of a product defect during the warranty pe-
riod, take the product and the RadioShack sales receipt
as proof of purchase date to any RadioShack store. Ra-
dioShack will, at its option, unless otherwise provided by
law: (a) correct the defect by product repair without
charge for parts and labor; (b) replace the product with
one of the same or similar design; or (c) refund the pur-
chase price. All replaced parts and products, and prod-
ucts on which a refund is made, become the property of
RadioShack. New or reconditioned parts and products
may be used in the performance of warranty service.
Repaired or replaced parts and products are warranted
for the remainder of the original warranty period. You will
be charged for repair or replacement of the product
made after the expiration of the warranty period.
This warranty does not cover: (a) damage or failure
caused by or attributable to acts of God, abuse, acci-
dent, misuse, improper or abnormal usage, failure to fol-
low instructions, improper installation or maintenance,
alteration, lightning or other incidence of excess voltage
or current; (b) any repairs other than those provided by a
RadioShack Authorized Service Facility; (c) consum-
ables such as fuses or batteries; (d) cosmetic damage;
(e) transportation, shipping or insurance costs; or (f)
costs of product removal, installation, set-up service ad-
justment or reinstallation.
This warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state.
RadioShack Customer Relations, Dept. W, 100 Throck-
morton St., Suite 600, Fort Worth, TX 76102
We Service What We Sell
3/97
RadioShack
A Division of Tandy Corporation
Fort Worth, Texas 76102
811080820B
3A8
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|