90 Gas
Users Guide
&
Installation Instructions
U1 215 02
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Minute Tour
Be safe
You need clean fresh air - so does your cooker. Burner flames produce exhaust gases, heat and
moisture. Make sure that the kitchen is well ventilated: keep natural ventilation holes open or
install a powered cooker hood that vents outside. If you have several burners on or use the cooker
for a long time, open a window or turn on an extractor fan. For more detail see the Installation
Instructions.
We recommend you read pages 20 & 21 if you have not used a gas cooker before.
We describe some basic guidelines on how to use a gas cooker safely.
Gas and Electricity on
Make sure that the gas supply is turned on and that the cooker is wired in and switched on.
The cooker needs electricity.
Peculiar smells
When you first use your cooker it may give off a slight odour. This should stop after a little use.
HOTPLATE BURNERS More about the burners on page 8
Make sure flames are under the
pans. Using a lid will help the
contents boil more quickly.
The drawing by each knob
indicates which burner that knob
controls. Push in and turn a
Adjust the flame height to suit
by turning the knob. On this
cooker the low position is
3
1
2
beyond high, not between high and
off. The small flame marks the ‘low
position’. Turn the knob towards it
after the contents of a pan have
boiled.
knob to the large flame symbol ( )
and press the igniter button or light
with a match.
Pans and kettles with concave bases
or down turned base rims should not
be used.
Simmering aids, such as
asbestos or mesh mats, are
NOT recommended. They will
Avoid using unstable and
misshapen pans that may tilt
easily and pans with a very
small base diameter e.g. milk pans,
single egg poachers. The minimum
pan diameter recommended is
120mm (about 43/4").
The Wok burner is designed to
provide even heat over a large
area. It is ideal for large pans
and stir frying. For heating smaller
pans the smaller burners may be
more efficient.
4
5
6
reduce burner performance and
could damage the pan supports.
2 Minute Tour continues over the page...
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Minute Tour - continued
THE GRIDDLE
The griddle fits a single pan
support, front to back. It is
designed for cooking food on
directly. Don’t use pans of any
Position the griddle over the
hotplate burners resting on the
pan support. The griddle can be
lightly brushed with cooking oil
before use. Light the hotplate
burners. Adjust the flame heights to
suit.
Don’t put it crossways - it will
not fit properly and will be
unstable.
2
1
3
Don’t put it on the Wok burner - it is
not designed to fit the Wok burner
pan support.
kind on it. The griddle surface is non-
stick and metal cooking utensils (e.g.
spatulas) will damage the surface.
Use heat resistant plastic or wooden
utensils.
Always leave space around the
griddle for the gases to escape.
Never fit two griddles side by
side. Large pans should also be
spaced well apart. The maximum
pan base diameter is 250mm (10in).
Preheat the griddle for a
maximum of 5 minutes before
5
4
adding food. Leaving it longer
may cause damage. The controls
can be turned to a lower position
simply by turning the control knobs
towards the lower position marked
with the small flame symbol.
The Griddle
Use the following heat settings as a guide for griddle cooking.
High/medium:
Drop scones, Bacon, Chops, Steak, Burgers.
Medium/low:
Potato cakes, Eggs, Fish cakes.
Experience will soon familiarise you with the correct setting to use for cooking. After cooking allow the
griddle to cool before cleaning.
Don’t put it on the Wok burner - it is not designed to fit the Wok burner pan support.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
THE GRILL More about the grill on page 8
CAUTION: Accessible parts may be hot when the grill is in use. Young children should be
kept away.
The burner does not glow red -
food cooks from the heat of the
flame. The first time you light
Remove the pan from the
bottom of the grill compartment.
After placing your food on the
grill tray pan, slide the grill pan
onto the side supports just
1
2
3
the grill there may be a little smoke
given off - this is perfectly normal.
below the burners. Make sure it is
pushed right in and touches the back
stop.
Natural gas cookers
LP gas cookers
Press in the grill knob, turn to
the large flame symbol ( ) and
press the igniter button or light
with a match.
The grill has a special safety device with stops the flow of gas to the grill
if the flame goes out. Turn the knob to the large flame symbol ( ). Press
in the grill knob. This lets gas through to the burner. Keep holding the
4
4
knob pressed in and press the igniter button or light with a match. Keep
holding the button for about 10 seconds
If when you let go of the control knob the burner goes out, the safety device
has not held in. Turn off the grill and wait one minute then try again this time
holding in the control knob for slightly longer.
The low position, marked with
the small flame symbol, is
beyond high, not between high
and off.
For best results preheat for 2
minutes with the grill pan in
position. After placing your food
The grill pan grid can be turned
over to give two grilling
positions.
5
6
7
on the grill pan grid, slide the grill pan
onto the side supports just below the
burners. Adjust the flame height to
suit by turning the knob.
Never close the grill door when
the grill is on.
Make sure it is pushed right in and
touches the back stop.
2 Minute Tour continues over the page...
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Minute Tour - continued
THE MAIN (GAS) OVEN More about the oven on page 9
The Main oven in your cooker
use the our special ‘Heatflow’
system.
Turn the control knob back to
the Mark you wish to cook on
and for best results pre-heat the
Push in and turn the knob
controlling the oven to Gas Mark
9. The oven will light
3
2
1
Because the oven burner is not
hidden under the oven base you will
see the burner flames at the back of
the oven - this is perfectly normal.
Initially the gas will burn with a small
flame but after approximately one
minute the flame will become larger
indicating that the oven is full on.
oven for 15 minutes before placing
your dishes in it.
automatically.
Dishes placed above the central
position will be cooked at
approx. one gas Mark higher,
dishes cooked below approx. one
gas Mark lower. You can therefore
cook dishes requiring different gas
Marks at the same time.
Dishes cooking on the central
shelf will cook at the gas mark
indicated on the knob.
6 MSloorewabocuotoslkowincgooking on
5
4
page 9.
The ‘S’ setting is a very low
temperature for slow cooking,
overnight or while you are out or at
work. The ‘S’ setting can also be
used for keeping food warm.
Handyrack (Main Oven)
More about the Handyrack on page 9.
Oven light
The Handyrack fits to the left hand
oven door only. Food cooking on it
is easy to attend to, because it’s
accessible when the door is open.
It can be fitted at two different
heights. One of the oven
shelves must be removed
and the other positioned to
suit.
Press the button to turn on the Main
oven light.
To fit the Handyrack, locate one side of it on
the door bracket.
If the oven light fails, turn off the
power supply before you change
the bulb. See the
‘Troubleshooting’ section for
details on how to change an oven
light bulb.
Then spring the other side out to clip it onto
the other bracket.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
THE TALL OVEN (ELECTRIC) More about the tall oven on page 9
Turn the oven knob to the
temperature you need.
The oven indicator light will glow
until the oven has reached the
temperature you selected. It will
When cooking foods with high
water content (e.g. oven chips)
there may be some steam
1
4
2
3
then cycle on and off during cooking.
visible at the grille at the rear of the
hotplate. This is perfectly normal.
The fan in the oven circulates
hot air continuously, which
means faster more even
The fan only setting. The fan
circulates air inside the oven but
the heating element is not
turned on. This setting is useful for
defrosting small quantities frozen
foods.
5
cooking.
The recommended cooking
temperatures for a fanned oven are
generally lower than a non-fanned
oven.
Whole chickens and large joints of
meat should be defrosted in the
refrigerator.
THE CLOCK More about the clock on page 12
To set the time of day
You can use the timer to turn the
ovens on and off. Check clock is set
to time of day.
Press and hold as above. At the same time, press (-) or (+)
until the correct time shows. Don’t forget it’s a 24 hour clock.
If you make a mistake or press the wrong button, turn off the
power supply for a minute or two and start again.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The hotplate burners
The Ovens
You should read ‘hotplate burners’ in the ‘2
Minute Tour’ before all the following
information
You should read ‘the oven’ in the
‘2 Minute Tour’ before all the following
information
If a burner flame goes out, turn the control knob
off and leave it for one minute before relighting it.
The wire shelves should always be pushed firmly
to the back of the oven.
You can remove the burner parts for
cleaning, see page 14.
Baking trays with food cooking on them should
be placed level with the front edge of the oven’s
wire shelves. Other containers should be placed
centrally. Keep all trays and containers away
from the back of the oven, as overbrowning of
the food may occur.
You should wipe the enamel top surface of the
cooker around the hotplate burners as soon as
possible after spills occur. Try to wipe them off
while the enamel is still warm.
For even browning, the maximum recommended
size of a baking tray is 325mm (123/4") by 305mm
(12") for the main oven and 230mm (9”) by
320mm (121/2”) for the Tall oven.
Avoid using unstable and misshapen pans that
may tilt easily and pans with a very small base
diameter e.g. milk pans, single egg poachers.
The minimum pan diameter recommended is
120mm (about 43/4"). Smaller pans will be
unstable.
When the oven is on, don’t leave the door open
for longer than necessary, otherwise the knobs
may get very hot.
Pans and kettles with down turned base rims
should not be used.
The Grill
• Always leave a ‘fingers width’ between dishes
on the same shelf This allows the heat to
circulate freely around them.
You should read ‘grill’ in the 2 Minute Tour’
before all the following information
Never close the grill door while the grill is
on.
• To reduce fat splashing when you add
vegetables to hot fat around a roast, dry them
thoroughly or brush lightly with cooking oil.
• Where dishes may boil and spill over during
cooking, place them on a baking tray.
Don’t leave the grill on for more than a few
moments, without the grill pan underneath it.
The Main (gas) oven
The oven is protected by a safety cut off, which
reduces the supply of gas to the oven if the
flames go out, e.g. an interruption to the mains
supply.
For best results, especially on toast, preheat the
grill with the grill pan in the cooking position for
two minutes before use.
• Plates can be warmed in the oven on the ‘S’
setting. The ‘S’ setting can be used to keep
foods hot for 3-4 hours after ‘normal’ cooking,
without drying out or overbrowning.
The grill trivet can be removed and the
food placed on it while you are waiting
for the grill to preheat.
The grill pan grid can be turned over to give two
grilling positions.
• The Cook & Clean oven liners (see Cleaning
your cooker) work better when fat splashes
are avoided. Cover meat when cooking.
• Sufficient heat rises out of the oven while
cooking to warm plates in the grill
You can brown the top of dishes cooked in the
oven, under the grill. Remove the grill trivet and
place the dish onto the base of the grill pan.
Slide the grill pan along the floor of the grill
cavity.
compartment.
• If you want to brown the base of a pastry dish,
preheat the baking tray for 15 minutes before
placing the dish in the centre of the tray.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
The Tall (electric) oven
The Handyrack
Cooking high moisture content foods can
create a ‘steam burst’, when the oven
door is opened. When opening the oven
stand well back and allow any steam to
disperse.
You should read ‘the oven’ in the
‘2 Minute Tour’ before all the following
information
The Handyrack should only be used with the
supplied meat tin which is designed to fit it. Any
other vessel could be unstable.
Main Oven shelves
The maximum weight which can be held by the
Handyrack is 5.5kg (12lb)
When the Handyrack is used in its highest
position, other dishes can be cooked on the
bottom shelf position of the oven or standing on
the base of the oven
When the Handyrack is used in its lowest
position, other dishes can be cooked on the
second shelf position of the oven or standing on
the base of the oven.
the shelf guard should be at the back pointing upwards
The oven shelves can be easily removed and
refitted.
Tall oven shelves
The tall oven is supplied with four normal
cooking shelves
and a plate warming shelf.
When using the tall oven you can cook on all
four shelves at the same time; but make sure
they are well spaced out to allow the hot air to
circulate.
The oven control settings and
cooking times given over the page
are intended to be used only as a
guide. Individual tastes may require
the temperature to be altered to
provide a preferred result.
To refit the shelf, line up the shelf with a groove
in the oven side and push the shelf back until the
ends hit the shelf stop. Lift up the front so the
shelf ends clear the shelf stops, and then lower
the front so that the shelf is level and push it fully
back.
Always leave at least one runner
space between shelves when 2 tier
cooking. Place baking trays,
individual cake tins or baking dishes
centrally on the oven shelf. For best
results pre-heat the oven for 15mins
(Main oven) or until the oven
indicator light goes out (Tall oven).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Oven cooking guide
GAS SHELF POSITION APPROXIMATE COOKING TIME
MARK FROM TOP
Meat
Beef (no bone)
3
3-4
3-4
30-35mins. per 500g.+30-35 mins.
20-25mins. per 500g.+20-25 mins.
30-35mins. per 500g.+30-35 mins.
25-30mins. per 500g.+25-30 mins.
35-40mins. per 500g.+35-40 mins.
25-30mins. per 500g.+25-30 mins.
Thoroughly thaw frozen joints
before cooking. Meat may be
roasted at Mk. 7 and the cooking
time adjusted accordingly. For
stuffed and rolled meats, add
approx. 10 min. per 500g. or
cook at Mk. 6 or 20min, then
Mk. 3 for the remainder.
6
Lamb
3
6
3
6
3-4
3-4
2-3
3-4
Pork and Veal
Poultry
Chicken (2.3kg)
Turkey (4.5kg)
(over 4.5kg)
3
6
3
6
3
6
3
6
3-4
3-4
3-4
3-4
4
20-25mins. per 500g.+20-25 mins.
15-20mins. per 500g.+15-20 mins.
25-30mins. per 500g.+25-30 mins.
20mins. per 500g.+20 mins.
20mins. per 500g.+20 mins.
15mins. per 500g.+15 mins.
25-30mins. per 500g.
For stuffed poultry, you could
cook at Mk. 6 for 20mins. and
then Mk.3 for remainder. Don’t
forget to include the weight of the
stuffing. For fresh or frozen
prepacked poultry, follow
instructions on the pack.
4
Thoroughly thaw frozen poultry
before cooking.
Duck/ duckling
4
4
20mins. per 500g.
Casseroles
Yorkshire Pudding
Fish
1-2
7
3-4
2
2-4 hours according to recipe.
Large tin 30-35 mins. Individual, 10-20 mins.
5
5
2
2
Fillets 15-20 mins. Whole 15-20mins. per 500g.
Steaks according to thickness.
Cakes
Very rich fruit
1
4
45-50mins. per 500g. of mixture.
When two tier cooking leave at
Christmas/ wedding etc.
least one runner space between
shelves. Position the baking tray
with the front edge along the
front of the oven shelf.
Fruit 180mm tin
Fruit 230mm tin
Madeira 180mm
Queen cakes
Scones
2
2
3
5
7
4
2 to 21/2 hours.
Up to 31/2 hours.
80-90 mins.
4
4
Rich fruit cakes made with self-
raising flour should be cooked on
Mk.4 for the first half hour at
least and then finished at the
setting shown.
2 & 4 or 3
2 & 4 or 3
15-25 mins.
10-15 mins.
Victoria sandwich
180mm tin
4
4
2 & 4 or 3
2 & 4 or 3
20-30mins.
30-40 mins.
230mm tin
Desserts
If cooking more than one tart at
the same time, swap them over
at approx. 25 mins. For even
browning the maximum size of
baking tray recommended is
320mm x 305mm. This ensures
free heat circulation.
Shortcrust tarts
Fruit pies
6
6
2 & 4
2-3
2-3
2-3-4
2-3-4
3
40-60 mins. on pre-heated tray.
35-45 mins.
Tartlets
6
10-20 mins. according to size.
20-40 mins. according to size.
20-40 mins. according to size.
11/2 to 2 hrs.
Flaky/rough puff
Puff pastry
7
8
If cooking a two tier load, when
the top tray is removed, the tray
in the lower position should be
raised to the higher shelf, or the
trays interchanged, for the
Meringues
‘S’
3
Baked egg custard
3
45-60 mins.
Baked sponge
pudding
5
3
3
40-45 mins.
2-3 hrs.
remaining cooking time.
Milk pudding
1-2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Tall Oven cooking guide
Oven
Food
Fish
Temperature
Approximate Cooking Time
180°C
Fillets 15-20mins.
180°C
180°C
Whole 10mins.per 500g + 10mins.
Steaks according to thickness.
ROAST MEATS
Beef with bone
150°C
190°C
150°C
190°C
170°C
190°C
150°C
190°C
20-25mins. per 500g + 20-25mins.
15-20mins. per 500g + 15-20mins.
30-35mins. per 500g + 30-35mins.
20-25mins. per 500g + 20-25mins.
30-35mins. per 500g + 30-35mins.
25-35mins. per 500g + 25-30mins.
35-40mins. per 500g + 35-40mins.
25-30mins. per 500g + 25-30mins.
Beef without bone
Lamb
Pork
Stuffed and rolled - Add approx. 10 mins. per 500g to above cooking times or cook at 200°C for 20mins. then 160°C
for remainder.
Thoroughly thaw frozen joints and poultry before cooking.
POULTRY
Chicken
150°C
190°C
150°C
200°C
20-25mins. per 500g + 20-25mins.
15-20mins. per 500g + 15-20mins.
20-25mins. per 500g + 20-25mins.
15-20mins. per 500g + 15-20mins.
Turkey
Stuffed Poultry - Cook at 200°C or at 200°C for 20mins. then 160°C for remainder.
Prepacked (fresh or frozen) follow packers cooking times
THOROUGHLY THAW FROZEN POULTRY BEFORE COOKING
CASSEROLE
140°C
200°C
2-4hrs according to recipe.
YORKSHIRE PUDDING
Large tin 30-35mins. Individual 10-20mins.
CAKES
Very Rich Fruit
Rich fruit (180mm)
Madeira (180mm)
Queen Cakes
Scones
140°C
145°C
150°C
170°C
200°C
170°C
45-50mins. per 500g mixture
21/2-3hrs.
80-90mins.
15-25mins.
10-15mins.
Victoria Sandwich
20-30mins.
PASTRIES
Plate Tart
Fruit Pie
190°C
190°C
190°C
200°C
200°C
100°C
45-50mins. Interchange after 25mins.
35-40mins.
Tartlets
15-20mins. according to size.
20-40mins. according to size.
20-30mins.
Puff Pastry
BREAD
MERINGUES
2-21/2hrs
PUDDINGS
Baked Egg Custard
Baked sponge pudding
Milk pudding
150°C
180°C
150°C
45mins.-1hr.
40-45mins.
2-3hrs.
500g is approximately 1lb (1lb 2oz)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Beef rare
medium
60°C/ 140°F
71°C/ 160°F
‘S’ (Slow) cooking (Main oven)
well done 77°C/ 170°F
82°C/ 180°F
The ‘S’ setting is a low temperature
setting.
Lamb
Pork fresh
cured
Poultry
Veal
88°C/ 190°F
77°C/ 170°F
90°C/ 195°F
77°C/ 170°F
You can cook on ‘S’ throughout, or use a 30
minute ‘boost’ period at gas mark 6 and then ‘S’
cook.
When roasting joints, poultry or pot
roasting, always cook at Mark 6 for 30
minutes at the beginning of the cooking
period.
Cooking using the timer
The timer can be used to turn just one oven or
both on and off automatically. The start and stop
time must be the same for both ovens but
different cooking temperatures can be set.
You can ‘S’ cook for periods of 6 to 12 hours.
This technique is particularly useful if you want to
cook a dish overnight or while you are out at
work during the day.
If you want to turn one of the ovens on at
the same time as the timer is set for
automatic cooking, you must wait until
the timer has turned on the oven/ ovens
first. Then you can adjust either of them
manually in the normal way.
Frozen foods must be thoroughly thawed
out before ‘S’ cooking.
Whole poultry should not be cooked on ‘S’.
Chicken casseroles are fine.
Casseroles must be brought to boiling
point on the hotplate immediately before
‘S’ cooking.
You can set the oven to turn on any time over
the following 24 hour period.
If you want to cook more than one dish,
choose dishes which require
Poultry and rolled joints should not be stuffed
before cooking. The stuffing should be cooked
separately. Poultry and pork should be cooked in
the top half of the oven, and other meats not
lower than shelf position 4.
approximately the same time. However,
dishes can be ‘slowed down’ slightly by
using small containers and covering
them with aluminium foil, or ‘speeded up’
slightly by cooking smaller quantities or
placing in larger containers.
A roasting joint should be covered with
cooking foil, or with a roasting bag to
reduce shrinkage and retain juices.
Very perishable foods such as pork or fish
should be avoided if a long delay period is
planned, especially in hot weather.
Should further browning be necessary, uncover
the meat and increase the temperature to Mark 4
for a short period.
Don’t place warm food in the oven.
Don’t use an oven already warm.
Don’t use if an adjoining oven is warm.
Cut root vegetables into small pieces
unless cooking whole, e.g. jacket
potatoes.
Avoid using wine or beer if there is a delay
period, as fermentation may take place.
Cover dishes tightly with a lid or foil to prevent
evaporation and transfer of flavour.
To avoid curdling, cream should be
added to dishes just before serving.
Once the oven has been loaded and the
‘S” setting is in operation resist the
temptation to open the oven door. Heat
will be lost and the cooking time
extended.
Fresh vegetables which may discolour during a
delay period should be coated in melted fat or
immersed in a water and lemon juice solution.
Fruit pies, custard tarts or similar wet mixtures on
top of uncooked pastry are only satisfactory if
there is a short delay period. Dishes containing
leftover cooked meat or poultry should not be
cooked automatically if there is a delay period.
A meat thermometer is recommended for
checking that a joint or poultry is sufficiently
cooked. Insert the probe through the thickest
part of the meat. The temperatures to be
expected are as follows.-
Whole poultry must be thoroughly
defrosted before placing in the oven.
Check that meat and poultry are fully
cooked before serving.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
The clock
To set the correct time of day.
To start and stop the oven automatically
See the ‘2 Minute Tour’ at the beginning of this
guide.
Before you set the clock, you must have two
numbers clearly in mind.
The ‘cook period’, which is the period of time you
want the oven to cook.
To time something that’s cooking
(minute minder)
The ‘stop time’, which is the time of day you want
the oven to stop cooking.
You cannot set a start time directly - this is set
automatically by setting the cooking period and
stop time.
Press and hold as above. At the same time press
(-) or (+) until the time you want to cook for is
shown, as below.
Press and hold as above. At the same time press
(-) or (+) until your required ‘cook period’ shows.
You can check time remaining by pressing
and cancel the beeper by pressing
Then press and hold as above. At the same time
press (-) or (+) until your required ‘stop time’
shows.
To stop automatically
AUTO will show in the display.
Set the oven to the required temperature. When
your cooking is finished the beeper sounds.
TURN THE OVEN KNOB TO 0 FIRST, then
Use when you have started the oven manually.
press once to stop the beep, press again to
return to manual cooking.
If you are out, don’t worry about the beeper going
off, it stops after a while. When you return, TURN
THE OVEN KNOB TO 0 FIRST, then press
twice, to return to manual cooking.
Press and hold as above. At the same time press
(-) or (+) until your required ‘Stop Time’ shows.
AUTO will show in the display. When your
cooking is finished the beeper sounds. TURN
THE OVEN KNOB TO 0 FIRST, then press
AUTO is showing, you want to reset to
manual cooking.
once to stop the beep, press again to return to
manual cooking.
When cancelling an automatic setting, any
cooking time already set must be returned to 0.00
before you can return to manual, by pressing the
button.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning your cooker
Hotplate burners
Essential information
Before thorough cleaning isolate the electricity
supply. Remember to switch on the electricity
Some models have a separate trim ring, which fits
on the burner head.
The burner heads and caps can be removed for
cleaning. Make sure they are absolutely dry before
replacing.
supply before use.
Never use paint solvents, washing
soda, caustic cleaners, biological
powders, bleach, chlorine based
bleach cleaners, coarse abrasives or
salt. Don’t mix different cleaning
products - they may react together
with hazardous results.
The LH hotplate
Recommended cleaning materials are
shown in the chart below.
If you want to move your cooker for cleaning,
see the section called ‘Moving your cooker’.
All parts of the cooker can be cleaned with hot
soapy water - but take care that no surplus
When refitting the burner head, make sure that the
notch lines up with the electrode or hole in the
base. Check that the burner head is level and that
the cap is fitted centrally on the burner head.
The Wok burner
The Wok burner is a little more complicated but it
also can be taken apart for cleaning.
‡ Indicates how to clean after the oven linings
have been removed. See opposite page for how
to remove the oven linings
* VEA is the Vitreous Enamel Association. Look
for aerosols with the VEA label.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
When reassembling the Wok burner, turn over
the large base ring and find the ‘D’ shaped area.
cloth. The oven doors should only be cleaned
with a soft cloth wrung out in clean hot soapy
water.
Cookers with window doors
On some models the oven door front panel can
be taken off so that the glass panels can be
cleaned. If the top edge of the oven door of your
cooker has a line of holes and there are screws
in the side edges then it can be taken apart for
cleaning.
Move the cooker forward to gain access to the
sides (see the ‘Moving the cooker’ section of
these instructions).
Turn the head until the ‘D’ matches the one on
the burner base. Turn the head over and place it
on the burner base. To fit the small inner burner,
find the larger electrode notch in the burner rim.
Line this up with the white ignition electrode and
place the inner burner on the large base ring.
Open the oven door slightly and remove the front
panel fixing screws from the door sides (two
each side).
some window doors only
Carefully lift off the outer door panel. The inside
face of the glass panels can now be cleaned -
take care not to disturb or wet the door
insulation. Please note that the door is triple
glazed but the inner two panels are fixed and
should not be separated. After cleaning carefully
refit the outer door panel and replace the side
fixing screws.
Now fit the two trim rings, making sure that they
are sitting down properly.
Grill
The Main Oven
The face of the grill burner will darken with use -
this is perfectly normal. Any fat or grease will
burn off. Do not try to clean it - the small holes
could get blocked and affect burner performance.
Cleaning is easier if carried out while the oven is
still warm. Before cleaning, cover the burner to
prevent the burner holes becoming blocked.
The inside of the oven and inner door panel can
be cleaned using any cleaner bearing the
Vitreous Enamel Association (VEA) label.
The grill pan and grid should be washed in hot
soapy water. Stubborn particles may be removed
from the grid by using a nylon brush.
Take care not to disturb the oven thermostat
temperature sensor at the top of the oven
opening.
Control Panel and Doors
Avoid using any abrasive cleaners including
cream cleaners, e.g. Cif, on brushed Stainless
Steel surfaces. For best results use a liquid
detergent e.g. Domestos Multi Surface Cleaner.
The control panel and control knobs should only
be cleaned with a soft cloth wrung out in clean
hot soapy water - but take care that no surplus
water seeps into the appliance. Wipe with a
clean dampened cloth then polish with a dry
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Before cleaning the oven, cover the burner at the
rear to stop the holes getting blocked as you
clean. If they are accidentally blocked, clean
them out with thin wire, such as fuse wire.
Removing the Oven Linings
The lining panels can be removed for cleaning
and for cleaning behind. Remove the shelves
first.
The enamelled oven burner trim (supplied with
some models only) can be removed for cleaning.
The oven burner trim hooks onto the front of the
oven burner bracket.
Each side of the oven is fixed with four fixing
screws. You don’t have to remove the screws to
remove the oven linings. Lift each side panel
upwards and they will slide off the screws. Then
pull them forwards.
When refitting make sure that the trim is in the
middle of the front of the oven burner bracket.
Once the linings are removed, the oven enamel
interior can be cleaned.
The Tall Oven
To clean the oven sides slide out the shelves,
unhook the supports from the oven sides and lift
out.
The Main Oven side linings
The oven has removable oven side lining panels
that have been coated with special enamel that
partly cleans itself. This does not stop all marks
on the lining, but helps to reduce the amount of
manual cleaning needed.
The self cleaning panels work better
above gas Mark 6. If you do most of your
cooking below this temperature,
occasionally remove the panels and wipe
with a lint free cloth and hot soapy water.
The panels should then be dried and
replaced and the oven heated at Gas
Mark 7 for about one hour. This will
ensure the self cleaning panels are
working effectively.
Don’t use steel wool (Brillo) or any other
materials that will scratch the surface. Don’t use
oven cleaning pads.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Moving your cooker
Switch off the electricity supply.
The cooker is heavy, two people may be
required to move it. There are two
levelling rollers at the back and also two
screw down levelling feet at the front.
Open the grill door and right hand oven door so
that you can get a good grip on the bottom of the
fascia panel as you move the oven. Lift the front
of the cooker slightly and pull forward.
Do not move the oven by pulling the door
handles or knobs.
Move the oven a bit at a time, checking behind it
to make sure the gas hose is not caught. Make
sure both electricity and gas cables have
sufficient slack to move the cooker forward as
you go along.
If a stability chain is fitted, release it as
you ease the cooker out. Don’t forget to
refit it when you replace the cooker.
When you replace the cooker, again check
behind to make sure that the electricity and gas
cables are not caught or trapped.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Food is cooking too slowly, too quickly, or burning
Cooking times may differ from your previous oven. The oven control settings
and cooking times are intended to be used only as a guide. Individual tastes
may require the gas mark to be altered one gas Mark either way, to get the
results you want. Try cooking at a higher shelf position and/or higher Mark.
Oven cooking times and temperatures may need to be increased when other
burners are in use. Are the Main oven burner ports blocked with spilt food?
The oven is not cooking evenly
Do not use a tin or baking tray larger than 340mm x 305mm in the main oven or
232mm x 321mm in the Tall oven.
If you are cooking a large item, be prepared to turn it round during cooking.
If more than one shelf is used, check that space has been left for the heat to
circulate. When a baking tray is put into the oven, make sure the front edge is
level with the front of the shelf.
Check that the door seal is not damaged and that the door catch adjusted so
that the door is held firmly against the seal.
NB the seal is intended to have a gap at the bottom of the door
A dish of water when placed on the shelf should be the same depth all over.
(For example, if it is deeper at the back, then the back of the cooker should be
raised up or the front lowered). If the cooker is not level arrange for your
supplier to level it for you.
Oven not coming on when turned on manually
Problems with the burner (main oven)
Are the oven burner ports blocked with spilt food? Are the burner flames
starting low and then rising to full height?
Electrical Problems
Is the power on? Is the clock illuminated? If not there may be something wrong
with the power supply. Is the clock flashing 0.00? If so set it to the correct time
of day. Has the Timer been set to AUTO by mistake? If AUTO is showing on the
clock display, press the ‘cook period’ button and reduce any set cooking time
showing to 0.00, with the (+) and (-) buttons. Press the button twice.
If this does not solve the problem contact a service person.
Oven not coming on when automatic cooking
Timer set correctly but oven knob left OFF by mistake?
Oven temperature getting hotter as the cooker gets older
If turning the knob down has not worked or only worked for a short time then
you may need a new thermostat. This should be fitted by a service person.
Steam is coming from the Tall oven
When cooking foods with a high water content (e.g. oven chips) there may be
some steam visible at the rear grille. Take care when opening the oven door as
there may be a momentary puff of steam when the oven door is opened. Stand
well back and allow any steam to disperse.
The Tall oven fan is noisy
The note of the oven fan may change as the oven heats up - this is perfectly
normal.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Grill Ignition faulty
Is the power on? Is the clock illuminated? If not there maybe something wrong
with the power supply. See ‘power supply’ section further on.
Grill not cooking properly
Are you using the pan and trivet supplied with the cooker? Is the pan being
used on the runners, not the floor of the compartment? Is the grill tray pushed
fully back to stop?
Hotplate ignition or hotplate burners faulty
Is the power on? Is the clock illuminated? If not there maybe something wrong
with the power supply.
See ‘power supply’ section further on.
Are the sparker (ignition electrode) or burner slots blocked by debris?
Is the burner trim correctly located?
Are the burner caps correctly located?
See the section entitled ‘Cleaning’
Hotplate burners will not light
If only one or all the hotplate burners will not light, make sure that the parts have
been replaced correctly after wiping or removing for cleaning.
Check that there is not a problem with your gas supply. You can do this by
making sure that other gas appliances you may have are working.
Do the burners spark when you push the button? If not check the power is on -
is the clock illuminated?
The Main oven light is not working
The bulb has probably blown. You can buy a replacement bulb (which is not
covered under the guarantee) from a good electrical shop. Ask for an Edison
screw fitting 15w 240v lamp, FOR OVENS. It must be a special bulb, heat
resistant to 300 °C. See the HELP leaflet for spares by mail order.
There is a glass cover over the bulb which has to be removed before you can
replace the bulb.
Turn off the power supply.
Unscrew the bulb cover by turning anticlockwise and unscrew the bulb. Screw in
the new bulb and refit the bulb cover.
Power supply. You think there may be a problem with it
First check the socket by trying out another piece of electrical equipment in it.
If that works, replace the fuse in the cooker plug. Use a 13 amp fuse.
Power failure
In the event of a failure in the electrical supply the grill and hotplate may be lit
using a match. The ovens however cannot be used either manually or
automatically until power is restored.
Oven ignition faulty (Main gas oven)
Is the power on? Is the clock running? - if not there may be something wrong
with the power supply.
See the section on ‘Checking the power supply’.
Check that the electrode and burner slots are not blocked by debris.
Has the Timer been set to auto by mistake, or after power cut?
Has the Timer been set correctly but oven tap not left OFF by mistake?
19
Download from Www.Somanuals.com. All Manuals Search And Download.
General Safety Instructions
The cooker must be installed by a CORGI
registered engineer in accordance with the
installation instructions. The installation must
comply with the relevant regulations and also the
local gas and electricity supply companies
requirements.
Take care when touching cooker, to minimize the
possibility of burns, always be certain that the
controls are in the OFF position and that it is cool
before attempting to clean the cooker.
Use dry oven gloves when applicable -
using damp gloves might result in steam
burns when you touch a hot surface.
Never operate the cooker with wet
hands.
IF YOU SMELL GAS
Don’t turn electric switches on or off.
Do not use a towel or other bulky cloth in place
of a glove. They might catch fire if they touch a
hot surface.
Don’t smoke
Don’t use naked flames
Do turn off the gas at the meter or cylinder
Do open doors and windows to get rid of the gas
Call your gas supplier.
Clean with caution. If a wet sponge or
cloth is used to wipe spills on a hot
surface, be careful to avoid steam burns.
Some cleansers can produce noxious
fumes if applied to a hot surface.
If you are using natural gas in the UK ring British
Gas - Trans Co on
Do not use unstable saucepans and position the
handles away from the edge of the hotplate.
0800 111 999
Babies, toddlers and young children
should not be allowed near the cooker at
any time. They should never be allowed
to sit or stand on any part of the
appliance. Teach them not to play with
controls or any other part of the cooker.
This appliance is designed for domestic
cooking only. Use for any other purpose
could invalidate any warranty or liability
claim.
The use of a gas cooking appliance results in the
production of heat and moisture in the room in
which it is installed. Ensure that the kitchen is
well ventilated: keep natural ventilation holes
open or install a mechanical ventilation device,
(mechanical extractor hood).
Never store anything of interest to children in
cabinets above a cooker - children climbing on
the cooker to reach them could be seriously
injured.
Clean only parts listed in this guide.
In the interests of hygiene and safety the cooker
should be kept clean at all times as a build up in
fats and other food stuff could result in a fire.
Prolonged intensive use of the appliance may
call for additional ventilation, for example
opening a window, or more effective ventilation,
for example increasing the level of mechanical
ventilation where present.
Always keep combustible wall coverings or
curtains etc. a safe distance away from your
cooker.
The cooker should be serviced by a qualified
service engineer and only approved spare parts
used. Have the installer show you the location of
the cooker control switch. Mark it for easy
reference. Always allow the cooker to cool and
then switch off at the mains and before cleaning
or carrying out any maintenance work, unless
specified otherwise in this guide.
Do not spray aerosols in the vicinity of the
cooker while it is in on.
Do not store or use combustible
materials, or flammable liquids in the
vicinity of this appliance.
Do not use water on grease fires. Never pick up
a flaming pan. Turn the controls off. Smother a
flaming pan on a surface unit by covering the
pan completely with a well fitting lid or baking
tray. If available use a multipurpose dry chemical
or foam-type fire extinguisher.
All parts of the cooker become hot with
use and will retain heat even after you
have stopped cooking.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Never leave the hotplate unattended at
high heat settings. Pans boiling over can
cause smoking and greasy spills may
catch on fire.
Do not use aluminium foil to cover shelves,
linings or the oven roof.
Make sure that your kitchen is well
ventilated at all times. Use extractor fans
or hoods when fitted.
Never wear loose-fitting or hanging clothes while
using the appliance. Be careful when reaching
for items stored in cabinets over the hotplate.
Flammable material could be ignited if brought in
contact with a hot surface unit and may cause
severe burns.
Never heat unopened food containers. Pressure
build up may make container burst and cause
injury.
The cooker is designed for cooking foods
only and must not be used for any other
purpose.
Take great care when heating fats and
oils, as they will ignite if they get too hot.
The oven should NOT be used for heating the
kitchen, not only does this waste fuel but the
control knobs may become overheated.
Use a deep fat thermometer whenever possible
to prevent overheating fat beyond the smoking
point.
When the oven is on DO NOT leave the
oven door open for longer than
necessary.
Never leave a chip pan unattended.
Always heat fat slowly, and watch as it
heats. Deep fry pans should be only one
third full of fat. Filling the pan too full of
fat can cause spill over when food is
added. If you use a combination of oils or
fats in frying, stir them together before
heating, or as the fats melt.
The specification of this cooker should not be
altered.
This appliance is heavy, take care when
moving it.
When the cooker is not in use ensure that the
control knobs are in the off position.
Foods for frying should be as dry as possible.
Frost on frozen foods or moisture on fresh foods
can cause hot fat to bubble up and over the
sides of the pan. Carefully watch for spills or
overheating of foods when frying at high or
medium high temperatures. Never try to move a
pan of hot fat, especially a deep fat fryer. Wait
until the fat is cool.
When the grill is on, do not use the top of
the flue (the slot along the back of the
cooker) for warming plates, dishes,
drying tea towels or softening butter.
When using an electrical appliance near the
hotplate, be sure that the cord of the appliance
does not come into contact with the hotplate.
If you find a crack in the Warmer surface
immediately disconnect the appliance
from the supply and arrange for its repair.
Take care that no water seeps into the appliance
Only certain types of glass, glass-
ceramic, earthenware or other glazed
containers are suitable for hotplate
cooking; others may break because of
the sudden change in temperature.
Do not allow anyone to climb, stand or
hang on any part of the cooker.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Dear Installer
Before you start your installation, please complete the details BELOW.
If your customer has a problem relating to your installation they will be
able to contact you easily.
Thank you
Installer’s Name
Installer’s Company
Installer’s Telephone number
22
Download from Www.Somanuals.com. All Manuals Search And Download.
You must be aware of the following
safety requirements & regulations
Provision of Ventilation
Prior to installation, ensure that the local distribution
conditions (nature of the gas and gas pressure) and
the adjustment of the appliance are compatible.
This appliance is not connected to a combustion
products evacuation device. Particular attention shall
be given to the relevant requirements regarding
ventilation.
This appliance shall be installed in accordance with
the regulations in force and only in a well ventilated
space. Read the instructions before installing or using
this appliance.
The room containing the cooker should have an air
supply in accordance with BS 5440 Part 2 : 2000. All
rooms require an openable window or equivalent,
while some rooms require a permanent vent in
addition to the openable window. The cooker should
not be installed in a bedsitting room with volume less
than 20m3. If it is installed in a room of volume less
than 5m3 an air vent of effective area 100cm2 is
required; if it is installed in a room of volume between
5m3 and 10m3, an air vent of effective area 50cm2 is
required; while if the volume exceeds 11m3, no air
vent is required.
In the UK the regulations and standards are as
follows:-
In your own interest and that of safety, it is law that all
gas appliances be installed by competent persons.
CORGI registered installers undertake to work to safe
and satisfactory standards. Failure to install the
appliance correctly could invalidate any warranty or
liability claims and lead to prosecution. The cooker
must be installed in accordance with
All relevant British Standards / Codes of
Practice, in particular BS 5440 Part 2 2000,
For Natural Gas - BS 6172 : 1990 and BS
6891 : 1998
If there are other fuel burning appliances in the same
room, BS 5440 Part 2 : 2000 should be consulted to
determine the requisite air vent requirements.
For LP Gas - BS 5482-1:1994 (when the
installation is in a permanent dwelling), BS
5482-2:1977, (when the installation is in a
caravan or other non permanent dwelling),
or BS 5482-3:1999 , (when the installation
is in a boat).
Location of Cooker
The cooker may be installed in a kitchen/kitchen diner
but NOT in a room containing a bath or shower.
NOTE:
An appliance for use on LPG shall not be installed
in a room or internal space below ground level.
e.g. in a basement.
The Gas Safety (Installation and Use)
regulations 1998.
The relevant Building / IEE regulations.
This appliance is designed for domestic cooking only.
Use for any other purpose could invalidate any
warranty or liability claim.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
You will need the following equipment to complete the
cooker installation satisfactorily
STABILITY BRACKET
If the cooker is to be
supplied with gas through
a flexible hose, a stability
bracket or chain must be
fitted.
GAS PRESSURE
TESTER
FLEXIBLE GAS HOSE
Must be in accordance
with the relevant
standards. For LP Gas it
should be suitable for
LPG, capable of 50mbar
pressure, 70°C
MULTIMETER
(for electrical checks)
These are not supplied
by with the cooker but
are available at most
builders merchants.
temperature rise and carry
a red stripe, band or label
You will also need the following tools:
1. Electric drill
2. Masonry drill bit
(only required if fitting the cooker on a stone or concrete floor)
3. Rawlplugs
(only required if fitting the cooker on a stone or concrete floor)
4. Steel tape measure
5. Cross head screwdriver
6. Flat head screwdriver
7. 4mm & 3mm Allen keys
8. Spirit level
9. Pencil
10. Adjustable spanner
11. Screws for fitting stability bracket
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the parts
Positioning the Cooker
The diagrams below show the minimum recommended
distance from the cooker to nearby surfaces.
Griddle plate
3 pan supports
Meat tin
The hotplate surround should be level with, or above,
any adjacent work surface. Above hotplate level a gap of
75mm should be left between each side of the cooker
and any adjacent vertical surface.
Grill pan and trivet
For non-combustible surfaces (such as unpainted metal
or ceramic tiles) this can be reduced to 25mm.
A minimum space of 650mm is required between the top
of the hotplate and a horizontal combustible surface.
Handyrack
2 main oven shelves
*Any cooker hood should be installed in accordance with
the hood manufacturer’s instructions.
Tall oven shelves & shelf
supports.
Plinth
For safety reasons curtains must not be fitted
immediately behind the cooker.
We recommend a gap of 910mm between units to allow
for moving the cooker. If a flush fit is required, fit the
cooker up to the unit at one side then fit the unit the
other side.
A clearance of 130mm is required if the cooker is near a
corner of the kitchen to allow the oven doors to open.
Unpacking the Cooker
Do not take any packaging off the cooker until it is
directly in front of the place it is to be installed (unless it
will not fit through a door in its outer packaging).
Cut the banding straps and lift the cardboard box off
the cooker, LEAVING THE COOKER STANDING ON
THE BASE PACKAGING. See the loose unpacking
sheet.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Moving the Cooker
The cooker is very heavy. Take great care.
We recommend two people manoeuvre the cooker.
Ensure that the floor covering is firmly fixed, or
removed to prevent it being disturbed when moving the
cooker around. You will need the levelling tool.
From the back tilt the cooker forward and remove the
rear half of the polystyrene base pack.
Carefully push the cooker backwards close to its final
position leaving just enough space to get behind it.
Take care not to damage the power cable.
Repeat from the front and remove the front half of the
poly base.
LOWER THE TWO REAR ROLLERS.
First fit the levelling tool on the hexagonal adjusting nut
as shown below.
Do not use the door handles or control knobs to
manoeuvre the cooker. Use the hotplate and griddle
bowl areas. Remove the pack base tray.
Levelling
You are recommended to use a spirit level on a shelf in
one of the ovens to check for level.
Make 10 complete (360º) turns clockwise. (This means
turning and removing the levelling tool 20 times).
Place the cooker in its intended position taking care not
to twist it within the gap between the kitchen units as
damage may occur to the cooker or the units.
The front feet and rear rollers can be adjusted to level
the cooker. To adjust the height of the rear of the
cooker use the levelling tool supplied to turn the
adjusting nuts at the front bottom corners of the cooker.
To set the front feet turn the bases to raise or lower.
Fit the Handles
Remove the 4mm Allen screws from the doors with the
hexagon key tool. Use the screws to fit the door
handles.
Make sure you lower BOTH REAR ROLLERS. There
are two adjusting nuts, one for each roller, at both the
front bottom corners of the cooker. Open the grill door
and the Tall oven door. Grip under the facia panel and
lift the front of the cooker.
The handles should be above the fixings.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas Connection
The Gas supply needs to terminate with a down facing
bayonet. The rear cover boxes limit the position of the
supply point.
Because the height of the cooker can be adjusted and
each connection is different it is difficult to give precise
dimensions. Ideally the house supply bayonet should
be in the shaded area shown in the diagram. Although
a 900mm hose can be used, a 1250mm hose will allow
slightly more flexibility in the positioning of the bayonet
and make moving the cooker easier. The hose should
be fitted so that both inlet and outlet connections are
vertical so that the hose hangs downwards.
Remove the 4mm Allen screws from the top corners of
the fascia and fix the front handrail in position.
Fitting a stability bracket
A stability bracket or chain (not supplied with the
cooker) should be fitted when the cooker is connected
to a flexible gas supply.
When fitting a stability bracket read these instructions
together with the leaflet supplied with the bracket.
view from the rear
A
B
position for gas supply connector
appliance gas inlet
The connector is located just below the hotplate level
at the rear of the cooker.
For Natural Gas the flexible hose must be in
accordance with B.S.669.
For LP Gas it should be capable of 50mbar
pressure, 70°C temperature rise and carry a red
stripe, band or label.
If in doubt contact, your supplier.
1. Place the cooker in its intended position and level
the cooker.
Screw connect the threaded end of the hose into the
gas inlet in the underside of the connector block on the
back of the cooker.
After completing the gas connection, check the cooker
is gas sound with a pressure test. When checking for
gas leaks do not use washing up liquid - this can
corrode. Use a product specifically manufactured for
leak detection.
2. Draw a pencil line 100mm from the front edge of the
levelling feet.
3. Mark the centre line for the bracket by measuring
450mm from the left hand side of the cooker.
4. Lower front roller and move cooker forward.
5. Measure back from pencil line 550mm to locate
front edge of the bracket. Fix the bracket to the
floor.
Pressure testing
6. Measure the height from floor level to engagement
edge in back of cooker. Add 3mm to this dimension
and assemble the stability bracket to this height.
(i.e. from floor level to underside of the top member)
and ensure the bracket does not foul the oven
burner assembly.
The gas pressure can be measured at the injector of
one of the LH hotplate burners. Remove the pan
support, burner head and caps. The injector is now
accessible.
For Natural Gas cookers the pressure should be
20mbar.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
For LP Gas cookers the pressure should be
29mbar for Butane
37mbar for Propane.
Re-check. If the resistance is still greater than l (ohm)
there may be a problem, consult a qualified electrical
engineer.
Reassemble burner top, making sure it is reassembled
in the correct way on the burner body.
POLARITY CHECK
The cooker must be connected to the power supply.
Your meter should be set on 300V ac scale.
Electrical Connection
Test at the cooker terminal block:
WARNING: THIS COOKER MUST BE EARTHED.
All external wiring must comply with the IEE
1. Test leads from L to N. Your meter should read
approx. 220-240V ac.
Regulations for the Electrical Equipment of Buildings.
Connection to the electrical supply can be made with
either a plug and socket or be permanently wired via a
double pole switch. The cooker is supplied with a 3
core cable 2m long. If a replacement cable is fitted it
must be 250v high temperature PVC (85°C), 1mm2.
Should the plug not fit the socket in your home, it
should be removed and replaced with a suitable plug.
Note: If a plug is fitted which is not suitable, it must be
cut off and disposed of properly. To avoid the risk of
electrocution, the plug must not be left where children
might find it and plug it into a supply socket.
2. Test leads from L to E. Your meter should read
approx. 220-240V ac.
3. Test leads from N to E. Your meter should read
approx. 0-15V ac.
If the readings are different from these values there is
an electrical fault. Rectify any fault and repeat the test.
If necessary repeat the test at the supply system
socket/spur - if the fault also occurs at this stage then
there is a house system fault which requires attention
by the Electrical Authority.
The customer should be warned NOT to use the
appliance until this examination has been carried out.
Three pin plugs to BS1363 with a capacity of not less
than 13A must be used and fitted with a 13 amp fuse
‘ASTA’ approved to BS 1362.
Grill check
After replacing the fuse the cover must be refitted. If
the cover is lost, the plug must not be used until a
replacement cover has been obtained from your
supplier. The colour of the correct fuse carrier is that of
the coloured insert in the base of the fuse recess, or
stated elsewhere on the plug. Always state this colour
when ordering a replacement fuse carrier.
IMPORTANT The wires in the mains lead are coloured
in accordance with the following code:-
GREEN AND YELLOW: EARTH
Open the grill compartment door.
Natural gas models
Press in the grill knob, turn to the large flame symbol
( ) and press the igniter button or light with a match.
LP gas models
LP gas models have an FSD with stops the flow of gas
to the grill if the flame goes out. Turn the knob to the
large flame symbol ( ). Press in the grill knob. This lets
gas through to the burner. Keep holding the knob
pressed in and press the igniter button or light with a
match. Keep holding the button for about 10 seconds
BLUE: NEUTRAL
BROWN: LIVE
The wires should be connected into the terminal of
your plug as shown:
If when you let go of the control knob the burner goes
out, the safety device has not held in. Turn off the grill
and wait one minute then try again this time holding in
the button for slightly longer.
Hotplate check
Check each burner in turn. Push in each knob and turn
it to the large flame symbol. Press the IGN button,
release the button when the burner lights.
Fitting the oven burner trim
(main gas oven only - supplied with
some models only)
Electrical checks
EARTH CONTINUITY CHECK
The cooker must be disconnected from the power
supply. Set your meter to (ohm) on the X1 scale and
adjust to zero if necessary.
Test the leads from any of the cooker’s earth points
(e.g. inside electric box cover) - to the earth pin on the
cooker’s plug - resistance should be less than
The loose oven burner trim hooks onto the front of the
oven burner bracket.
l
(ohm). If it is not, check all the earth wires for
continuity. Check that all contacts are clean and tight.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Push in and turn one of the oven knobs to Mark 9, the
timer will run until the ‘cook period’ starts, when the
oven solenoid will open and the burner will light
automatically. The cooking symbol ( ) will show. At
the end of the ‘cooking period’ the solenoid will close,
the oven burner will go out and the beeper will sound
(the beeper may be stopped by pressing the timer (
)
button). The flashing (AUTO) symbol is a reminder to
reset to manual operation. Pressing the reset’ button
(
) once to stop the beep and a second time to return
to manual, turn off the oven knob.
CONTROL KNOB (THERMOSTAT) CHECK
Set timer to manual. Check each oven in turn. Push in
and turn the control knob to Mark 9. A series of sparks
will occur at the oven electrode and when the oven
burner lights the sparking will stop. A small flame will
appear on the oven burner, but as this flame is
‘sensed’ by the flame supervision device, the gas flow
will come on full after a short delay. Heat each oven for
10 minutes at Mark 9 then turn to Mark 1 and check
that the flame size has reduced. Turn off each oven
and check that the oven burner goes out.
Main Oven check
The clock must be set to the time of day before the
ovens will work.
Tall oven
Turn on the Tall oven and check that it heats up.
Fitting the plinth
Loosen the 3 screws along the front bottom edge of the
cooker. Hook the central keyhole over the central
screw. Twist and fit each end keyhole over their
respective screws. Tighten the fixing screws.
Press and hold as above.
At the same time, press - or + until the correct time
shows.
Don’t forget it’s a 24 hour clock.
If you make a mistake or press the wrong button, turn
off the power supply for a minute or two and start
again.
CONTROL KNOB (THERMOSTAT) CHECK
If (AUTO) is flashing, press and release the manual
(
) button. Check each oven in turn. Push in and turn
the control knob to Mark 9. A series of sparks will occur
at the oven electrode and when the oven burner lights
the sparking will stop. A small flame will appear on the
oven burner, but as this flame is ‘sensed’ by the flame
supervision device, the gas flow will come on full after
a short delay. Heat each oven for 10 minutes at Mark 9
then turn to Mark 1 and check that the flame size has
reduced. Turn off each oven and check that the oven
burner goes out.
TIMER AND SOLENOID CHECK
Automatic Operation of Timer: The gas supply to each
oven can be controlled by the timer. Set a ‘cooking
period’ time by pressing and releasing the (
and using the + button to give a time of 2 minutes. By
pressing and releasing the ‘stop time’ button (
stop time is displayed. Add 3 minutes to this time by
using the + button. The display will automatically
change to show the time of day, the cooking symbol
) button
Customer care
Please complete your details in the inside cover of this
Guide. Then replace this Installation Guide back in the
Customer Care Pack in the correct position. Please
inform the user how to operate the cooker and hand
over the Customer Care Pack.
) the
(
) will go out and (AUTO) will show.
Thank you.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Circuit Diagram
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
This cooker is designed for use on either :-
NATURAL GAS (Cat I2H ) at 20mbar or
LP GAS (Cat I3+ ) Butane 29mbar / Propane 37mbar.
NB: THE NATURAL GAS AND LP GAS VERSIONS OF THESE COOKERS ARE DIFFERENT MODELS
AND CANNOT BE CONVERTED FROM ONE GAS FAMILY TO THE OTHER.
INSTALLER: Please leave these instructions with the User.
DATA BADGE LOCATION:
Country of Destination: GB/IE
Gas
Cooker back, serial number repeater badge below oven door opening.
Electric
Natural Gas
Butane
Propane
20mbar
29mbar
37mbar
220 - 240V 50Hz
(See appliance data badge for test pressures)
Dimensions
Overall height
minimum 893mm maximum 920mm
900mm See ‘Positioning of Cooker’
Overall width
Overall depth
648mm
Space for fixing
Minimum space above hotplate
See ‘Positioning of Cooker’
650mm
Connections
Gas:
Electric
220 - 240V 50Hz
Rp 1/2 at rear right-hand side
Ratings
Natural Gas
L.P. Gas
Injector
Injector
Hotplate
Wok burner
3.5kW internal 80
external 129
3.0kW 134
Medium Burners 1.7kW 109
3.5kW(246g/h)
internal 54
external 77
Large Burner
3.0kW (210g/h) 87
1.7kW (119g/h) 68
Small Burner
Main Oven
Tall Oven (electric)
1.0kW 75
3.2kW 237
2.5kW
1.0kW (70g/h)
2.9kW (224g/h) 85
2.5kW
51
Grill
2.73kW 190
2.73kW (192g/h) 85
Gas burner inputs based on Gross Calorific Value
Total electrical load 2.6kW approx.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|