RCA Flat Panel Television PSP42300 User Guide

U
S
E
R ’  
S
M
A
N
U
A
L
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety Information  
TO REDUCETHE RISK OF ELECTRIC SHOCK, DO NOT REMOVE  
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.  
REFER SERVICINGTO QUALIFIED SERVICE PERSONNEL.  
WARNING  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
This symbol indicates “dangerous  
voltage” inside the product that  
presents a risk of electric shock or  
personal injury.  
This symbol indicates  
important instructions  
accompanying the product.  
FCC Information  
PRECAUTIONS  
Please read this manual carefully before using your  
Cinema Screen Monitor and keep the manual handy for  
future reference.  
FCC Regulations state that unauthorized changes or  
modifications to this equipment may void the  
user's authority to operate it.  
This equipment has been type tested and found to  
comply with the limits for a Class B Digital Device  
in accordance with the specifications in Part 15 of  
the FCC rules. These rules are designed to provide  
reasonable protection against radio and television  
interference in a residential installation. This  
equipment generates and can radiate radio  
frequency and, if not installed and used in  
WARNING  
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT  
EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO  
DO NOT USE THIS UNIT’S PLUG WITH AN  
EXTENSION CORD RECEPTACLE OR OTHER  
OUTLETS, UNLESS ALL PRONGS CAN BE FULLY  
INSERTED. REFRAIN FROM OPENING THE CABINET  
AS THERE ARE HIGH-VOLTAGE COMPONENTS  
INSIDE. REFER SERVICING TO QUALIFIED SERVICE  
PERSONNEL.  
accordance with the instructions, may cause  
harmful interference to radio communications.  
However, there is no guarantee that interference  
will not occur in a particular installation.  
If this equipment does cause interference to the  
radio or television reception (which you can  
determine by turning the equipment off and on), try  
to correct the interference by one or more of the  
following measures:  
INDUSTRY CANADA COMPLIANCE NOTICE  
This Class B digital apparatus meets all requirements of  
the Canadian Interference-Causing Equipment  
Regulations.  
Reorient or relocate the receiving antenna (that  
is, the antenna for the radio or television that is  
"receiving" the interference).  
DECLARATION OF CONFORMITY  
This device complies with Part 15 of the FCC rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference, and  
(2) this device must accept any interference received,  
including interference that may cause undesired  
operation.  
Change the position of the Cinema Screen  
display with respect to the radio or television  
equipment that is receiving the interference.  
Move the Cinema Screen display away from  
the equipment receiving the interference.  
Product: Cinema Screen Display  
Equipment Classification: Class B Computer Peripheral  
Model: PR42300  
Plug the Cinema Screen display into a different  
wall outlet so the receiver and the equipment  
are on different branch circuits.  
If these measures do not eliminate interference,  
please consult your dealer or an experienced radio/  
television technician for additional suggestions.  
Also, the Federal Communications Commission has  
prepared a helpful booklet, "How to Identify and  
Resolve Radio/TV Interference Problems." This  
booklet is available from the U.S. Government  
Printing Office, Washington D.C., 20402. Please  
specify stock number 004-000-00345-4 when  
ordering copies.  
We hereby declare that the equipment specified above  
conforms to the technical standards as specified in the  
FCC rules.  
Thomson Consumer Electronics, Inc.  
10330 N. Meridian St.  
Indianapolis, IN 46290  
Phone: 1-800-433-8974  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNINGS AND SAFETY PRECAUTIONS  
IMPORTANTTIPS: CARING FOR YOUR  
CINEMA SCREEN MONITOR  
The Cinema Screen monitor is designed and manufactured  
to provide long, trouble-free service. No maintenance other  
than cleaning is required. Use a soft dry cloth to clean the  
panel. Never use solvents such as alcohol or thinner to  
clean the panel surface.  
TO AVOID DAMAGE AND PROLONG OPERATING LIFE:  
1. Use only with 120V 50/60Hz AC power supply.  
Continued operation at line voltages greater than 120  
Volts AC will shorten the life of the unit, and might  
cause a fire hazard.  
The Cinema Screen display panel consists of fine picture  
elements (cells). Although the Cinema Screen display  
panels are produced with more than 99.99 percent active  
cells, there may be some cells that do not produce light or  
remain lit.  
2. Handle the unit carefully when installing it.  
3. Locate set away from heat, excessive dust, and direct  
sunlight.  
For operating safety and to avoid damage to the unit, read  
carefully and observe the following instructions.  
4. Protect the inside of the unit from liquids and small  
metal objects. In case of accident, unplug the unit and  
have it serviced by an authorized service center.  
To avoid shock and fire hazards:  
1. Provide adequate space for ventilation to avoid internal  
heat build-up. Do not cover rear vents or install in a  
closed cabinet or shelves.  
5. Do not hit or scratch the panel surface as this causes  
flaws on the surface of the screen.  
6. For correct installation and mounting it is strongly  
recommended to use a trained, authorized Cinema  
Screen dealer.  
The unit is equipped with cooling fans. If you install  
the unit in an enclosure, be sure there is adequate  
space at the top of the unit to allow hot air to rise and  
escape.  
7. Like all phosphor-based display devices, Cinema  
Screen monitors can be susceptible to uneven  
If the monitor becomes too hot, the overheat protector  
will be activated and the monitor will be turned off. If  
this happens, turn off the power to the monitor and un-  
plug the power cord. If the room where the monitor is  
installed is particularly hot, move the monitor to a  
cooler location, and wait for the monitor to cool for 60  
minutes.  
phosphor aging under certain circumstances. Certain  
operating conditions, such as the continuous display of  
a static image over a prolonged period of time, can  
result in uneven phosphor aging if proper precautions  
are not taken. To protect your investment in this Cinema  
Screen monitor, please adhere to the following  
guidelines and recommendations for minimizing the  
occurrence of uneven phosphor aging:  
If the problem persists, contact your Cinema Screen  
dealer for service.  
Always enable and use your computer’s screen saver  
function during use with a computer input source.  
2. Do not use the power cord plug with extension cords  
or outlets unless all prongs can be completely inserted.  
Display a moving image whenever possible.  
3. Do not expose unit to water or moisture.  
Always power down the monitor when you are  
finished using it.  
4. Avoid damage to the power cord, and do not attempt  
to modify the power cord.  
If viewing with a 4/3 aspect ratio for long periods of  
time, set side gray level at 3 or 4.  
5. Unplug unit during electrical storms or if unit will not  
be used over a long period.  
6. Do not open the unit which has potentially dangerous  
high voltage components inside. If the unit is damaged  
from opening the cabinet the warranty will be void.  
Moreover, there is a serious risk of electric shock.  
IF THE CINEMA SCREEN MONITOR IS IN LONG TERM  
USE OR CONTINUOUS OPERATION TAKE THE  
FOLLOWING MEASURES TO REDUCE THE LIKELIHOOD  
OF UNEVEN PHOSPHOR AGING:  
7. Do not attempt to service or repair the unit. TCE is not  
liable for any bodily harm or damage caused if  
unqualified persons attempt service or open the back  
cover. Refer all service to authorized Cinema Screen  
Service Centers.  
Lower the BRIGHTNESS and CONTRAST levels as  
much as possible without impairing image readability.  
Display an image with many colors and color  
gradations (i.e. photographic or photo-realistic images).  
Create image content with minimal contrast between  
light and dark areas (for example, white characters on  
black backgrounds). Use complementary or pastel  
color whenever possible.  
Avoid displaying images with few colors and distinct,  
sharply defined borders between colors.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Safety Information ............................................................1  
Warnings and Safety Precautions ................................................ 2  
IMPORTANT TIPS: Caring for Your Cinema Screen Monitor....... 2  
Getting Started .................................................................5  
Contents of the Package.............................................................. 6  
Attching the Ferrite Cores ........................................................... 6  
Part Names and Functions – Front View...................................... 7  
Part Names and Functions – Back View ...................................... 8  
Battery Installation ...................................................................... 9  
Connecting an HD Receiver ....................................................... 9  
The Back of the HD Receiver ................................................ 9  
Connecting Your VCR Or Laserdisc Player ................................ 10  
Connecting Your DVD Player ................................................... 10  
Connecting a Personal Computer.............................................. 10  
Connecting Components to the Cinema Screen Monitor........... 11  
Connecting External Speakers to the Cinema Screen Monitor ... 12  
A Quick Tour of the Remote Control ......................................... 13  
Using Your Remote Control ................................................. 15  
Inserting Batteries .............................................................. 15  
Programming the Remote .................................................... 15  
Find Out If You Need to Program the Remote.................... 15  
How to Program the Remote ............................................. 16  
Using Automatic Code Search ........................................... 16  
Using Direct Entry ............................................................. 17  
How To Use the Remote Control  
After You’ve Programmed It ................................................. 17  
Programmable Codes for the Remote Control ...................... 18  
The Menu System ...........................................................21  
Basic Operations ...................................................................... 22  
Power.................................................................................. 22  
Volume ............................................................................... 22  
Mute ................................................................................... 22  
Navigating the Menus ......................................................... 23  
On-Screen Menu Operation ..................................................... 23  
The PICTURE QUALITY Menu.................................................. 24  
Setting the Picture Mode ..................................................... 24  
Adjusting the Picture Settings in MEMORY Mode ................ 25  
Setting the Color Temperature ............................................. 26  
Reducing Noise in the Picture ............................................. 27  
The AUDIO Menu .................................................................... 28  
The SCREEN Menu ................................................................... 29  
Selecting a Viewing Size...................................................... 29  
Adjusting the Picture Position and Size................................ 30  
Auto Picture ........................................................................ 30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
The FUNCTION Menu ............................................................. 31  
On-Screen Displays............................................................. 31  
Adjusting the Position of the Menu Display ......................... 31  
Setting the POWER SAVER for Computer Images................. 32  
The POWER/STANDBY Indicator ........................................ 32  
Setting the Gray Level for the Sides of the Screen ................ 33  
Setting the Brightness Level with the  
PLE+INVERSE Feature ....................................................... 33  
Adjusting for Flickering with Film Mode.............................. 34  
Resetting to Default Values .................................................. 34  
The OPTIONS Menu ................................................................ 35  
Setting the Audio Inputs ...................................................... 35  
Setting the BNC Connectors ................................................ 35  
Setting a Computer Image to the Correct RGB  
Select Mode................................................................... 36  
Setting the Cinema Screen Monitor to the correct  
HD Receiver Mode ....................................................... 37  
Adjusting the Display in RGB3 Input Mode ......................... 37  
The SETUP Menu...................................................................... 38  
Confirming the Frequencies and Polarities of Input Signals.. 38  
Selecting the Language for the Menus ................................. 38  
Setting the Video Signal Format ........................................... 38  
The AUTOTUNING SETUP Menu ............................................ 39  
Autotuning the Component Buttons on he Remote Control....... 39  
SLEEP TIMER ............................................................................ 39  
Setting the Sleep Timer ........................................................ 39  
Cancelling the Sleep Timer................................................ 39  
Reference........................................................................41  
Installing the Cinema Screen Monitor ....................................... 42  
Attaching optional mounts or stand to the Cinema  
Screen monitor ................................................................. 42  
Connecting Your PC Or Macintosh Computer........................... 43  
Mini D-sub 15 Pin VGA Signal Composition ....................... 43  
Specifications ........................................................................... 44  
Troubleshooting ........................................................................ 45  
The Cinema Screen Monitor Menu System ............................... 46  
Supported Resolution................................................................ 48  
RCA Cinema Screen Display Limited Warranty ......................... 49  
Cinema Screen Accessories ...................................................... 50  
Index ........................................................................................ 51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup and connections  
GETTING STARTED  
setup and  
connections  
1
Welcome to the future!The Cinema Screen monitor  
combines advanced technology with sophisticated design to  
create a sleek, elegant monitor that fits unobtrusively into  
any environment – while still making a lasting impression.  
This first section contains all of the information you need to  
get your Cinema Screen monitor connected and set up.The  
rest of the manual gives you guidance in using the functions  
of your monitor, as well as technical information,  
The menu system  
2
3
troubleshooting, and warranty information.  
reference  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup and connections  
CONTENTS OF THE PACKAGE  
Cinema Screen monitor  
Power cord  
Ferrite cores  
RGB cable (Mini D-Sub 15-pin to Mini D-Sub 15- pin connector)  
Remote control unit with two AA batteries  
User’s manual  
It is highly recommended that you have your Cinema Screen monitor installed by a professional. If  
you are installing the monitor yourself, refer to the Reference section.  
NOTE: If you are planning on attaching the floor stand to your Cinema Screen monitor (and not the optional wall mount unit)  
you may want to use the safety metal fittings (provided) to give your monitor extra stability.  
The safety metal fittings attach to the back of the screen and can then be used to secure the monitor to the wall with strong wire.  
Contact your trained, authorized Cinema Screen dealer for professional installation.  
In order to conform to mandatory FCC standards, you must attach the supplied ferrite cores to both ends of the power cable  
(see below).  
If you are connecting a computer to the monitor, you must attach the ferrite cores to both ends of the DVI cable to meet  
FCC standards.  
ATTACHING THE FERRITE CORES  
Set the ferrite cores on the both ends of the DVI cable (not supplied), and one end of the power cable (supplied). Close the  
lid tightly until the clamps click. Use the band to secure the ferrite core (supplied).  
DVI cable  
(not supplied)  
band  
band  
connector  
core (small)  
core (small)  
band  
power cable (supplied)  
(monitor side)  
core (large)  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup and connections  
PART NAMES AND FUNCTIONS – FRONT VIEW  
POWER  
STANDBY  
VOLUME  
MENU• OK  
DOWN  
UP  
LEFT/-  
RIGHT/+  
INPUT  
GO BACK  
VOLUME  
DOWN  
POWER • STANDBY  
MENU • OK  
U
P
LEFT/-  
RIGHT/+  
INPUT • GO BACK  
1
2
3
5
6
4
1. MENU•OK – If no menu is displayed, brings up the  
menu. If a menu is displayed, press to select a  
highlighted option.  
4. INPUT • GO BACK – Switches the input, in the following  
order:  
2. VOLUME – Adjusts the volume. When an on-screen menu  
is being displayed, moves highlight up and down (  
and ).  
*Note: You can set up CMPNT1 or RGB2, but not both.  
When an on-screen menu is being displayed, returns  
you to the previous menu.  
3. LEFT/- AND RIGHT/- – When Zoom mode is on (press OK  
on the remote to turn ZOOM on and bring up the zoom  
icon) press Right/+ to enlarge the image or Left/- to  
reduce the image.  
5. POWER/STANDBY indicator When the power is on,  
the light is green. When the power is in Standby Mode,  
the light is red.  
When a menu is being displayed, used to navigate  
through menu ( and ).  
6.  
Turns the monitors power on and off.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup and connections  
PART NAMES AND FUNCTIONS – BACK V IEW  
RGB  
3
DIGITAL RGB  
+
LEFT  
-
-
RGB  
R
1
RIGHT  
+
C
R
PR  
G
B
Y
C
Y
B
PB  
EXTERNAL  
CONTROL  
H-SYNC  
V-SYNC  
L(MONO)  
R
REMOTE  
CONTROL  
CONTROL  
LOCK  
ON/  
VIDEO  
VIDEO  
VIDEO  
1
2
3
OFF  
L(MONO)  
R
Y
Y
C
C
B
R
P
P
B
R
L(MONO)  
R
+
LEFT  
-
-
RGB 3  
DIGITAL RGB  
6
7
RIGHT  
+
1
RGB 1  
EXTERNAL  
CONTROL  
1. EXT SPEAKER L and R Connect speakers here.  
R
C
R
PR  
2
G
B
Y
C
Y
2. EXTERNAL CONTROL This terminal is used when the  
Cinema Screen monitor is controlled by external  
equipment.  
B
PB  
8
REMOTE  
3
4
CONTROL  
H-SYNC  
V-SYNC  
CONTROL  
LOCK  
ON/  
OFF  
3. REMOTE CONTROL This jack is for connecting a wired  
remote, which is primarily for commercial applications.  
The remote included with your monitor is wireless and  
doesnt require connection to the monitor.  
L(MONO)  
R
VIDEO 1  
VIDEO 2  
VIDEO 3  
4. CONTROL LOCK When CONTROL LOCK is in the ON  
position, the buttons on the monitors control panel dont  
function.  
9
AC IN  
5
L(MONO)  
R
10  
11  
5. AC IN Connect the included power cord here.  
6. RGB3 (DVI 29pin) Inputs a digital RGB signal.  
7. RGB1 Connect HD receiver here.  
Y
Y
C
C
B
R
P
P
B
R
L(MONO)  
R
8. BNC SELECT –  
RGB2: Inputs the analog RGB signal.  
CMPNT2: Connect DVDs, Laserdiscs, etc. here.  
9. VIDEO 01, 2, 3 Connect VCRs, DVDs, Laserdiscs, etc.  
here.  
10. AUDIO1, AUDIO2, AUDIO3 Connect audio here.  
11. CMPNT1 Connect Laser discs, etc. here.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup and connections  
BATTERY INSTALLATION  
Remove the battery compartment cover from the back of the remote  
control.  
Insert batteries. Make sure the polarities (+ and -) are aligned correctly.  
Replace cover.  
CONNECTING AN HD RECEIVER  
RCA and PROSCAN HD (high definition) receivers come equipped with an  
RGB output jack for optimum quality. Using the RGB cable provided,  
connect the HD MONITOR OUT jack on the back of your HD receiver to  
the RGB1 (HD MONITOR IN)/AUDIO1 IN jack on the back of the Cinema  
Screen monitor.  
Installing the batteries  
If your HD receiver does not have the type of jack pictured on the right,  
connect your HD receiver using the component video jacks and RCA  
cable.  
For more information on HD receiver connections, see your HD receiver  
users manual.  
THE BACK OF THE HD RECEIVER  
RGB cable  
R
R
L
ACCESS CARD  
L
S-VIDEO HD MONITOR OUT  
VIDEO  
DIGITAL AUDIO  
OUTPUT  
VCR  
CONTROL  
AUDIO  
SATELLITE  
IN  
OUT TO TV ANTENNA B ANTENNA A  
IN IN  
PHONE JACK  
HD MONITOR OUT jack  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup and connections  
CONNECTING YOUR VCR OR LASERDISC PLAYER  
Use common RCA cables (not provided) to connect your VCR or laserdisc  
player to your Cinema Screen monitor. To connect your VCR or Laserdisc  
player:  
1. Turn off the power to the monitor and VCR or laser disc player.  
2. Connect one end of your RCA cable to the video output connector on  
the back of your VCR or laser disc player. Connect the other end to the  
video input on the monitor.  
3. Use standard RCA cables to connect the audio from your VCR or laser  
disc player to AUDIO2 input jacks on the monitor (if your VCR or laser  
disc player has this capability). Be careful to keep your right and left  
channel connections correct for stereo sound.  
RCA cables (audio/video cables) are sold as a bundled set.  
4. Turn on the Cinema Screen monitor and the VCR or laser disc player.  
NOTE: Refer to your VCR or laser disc player users manual for more  
information about your equipments video output requirements.  
CONNECTING YOUR DVD PLAYER  
To connect your Cinema Screen monitor to a DVD player:  
1. Turn off the power to the monitor and DVD player.  
2. Use a standard video cables to connect your DVD player to the  
CMNT1 input on the monitor, or use the DVD players S-Video output.  
(Use a standard S-Video cable to connect to the S-Video input on the  
Cinema Screen monitor.)  
3. Turn on the monitor and the DVD player.  
CONNECTING A PERSONAL COMPUTER  
If you are connecting a computer to the monitor, you must attach ferrite  
cores to both ends of the DVI cable to meet FCC standards (see page 6).  
If you have a computer with digital RGB output, connect it to the RGB3  
jack on the monitor.  
For IBM VGA (or compatible) or Macintosh (or compatible) connect to the  
RGB1 jack on the monitor.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup and connections  
CONNECTING COMPONENTS TO THE CINEMA SCREEN MONITOR  
Personal computer with a digital RGB output  
Signal cable (supplied)  
To Mini D-Sub 15 pin connector on the PlasmaSync 4210W  
RGB 3  
DIGITAL RGB  
RGB 1  
IBM VGA or Compatibles  
R
CR  
PR  
G
B
Y
Y
CB  
PB  
Macintosh or Compatibles  
RGB  
3
DIGITAL RGB  
H-SYNC  
V-SYNC  
RGB  
R
1
Monitor adapter for Macintosh  
C
R
PR  
G
B
Y
C
Y
B
PB  
H-SYNC  
V-SYNC  
L(MONO)  
R
L(MONO)  
R
VIDEO  
VIDEO  
VIDEO  
1
2
3
VIDEO 1  
VIDEO 2  
VIDEO 3  
L(MONO)  
R
Y
Y
C
B
P
B
C
R
P
R
L(MONO)  
R
L(MONO)  
R
VCR or Laser Disc Player  
Y
Y
CB  
PB  
CR  
PR  
L(MONO)  
R
DVD Player  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup and connections  
RGB  
3
DIGITAL RGB  
+
LEFT  
-
-
RGB  
R
1
RIGHT  
+
C
R
PR  
G
B
Y
C
Y
B
PB  
EXTERNAL  
CONTROL  
H-SYNC  
V-SYNC  
REMOTE  
L(MONO)  
R
CONTROL  
CONTROL  
LOCK  
ON/  
OFF  
VIDEO  
VIDEO  
VIDEO  
1
2
3
L(MONO)  
R
Y
Y
C
B
P
B
C
R
P
R
L(MONO)  
R
CONNECTING EXTERNAL SPEAKERS* TO THE CINEMA SCREEN MONITOR  
The Cinema Screen monitor doesnt have internal speakers, so in order to get sound you must connect external speakers.  
External speakers can reproduce sound from VIDEO or RGB signal sources.  
External speakers may be connected directly to the SPEAKERS terminals or indirectly by connecting a stereo system amplifier  
to the audio outputs.  
CAUTION: Unplug the monitor and all connected components before connecting external speakers. Use only speakers  
with 6 to 8-ohm impedance and a power output rating of 7 watts or more.  
To connect external speakers directly to the Cinema Screen monitor:  
1. Strip the ends of the speaker wires.  
2. Press down the tabs below the speaker terminals and insert the speaker wire and release the tab to secure the speaker  
wire connection.  
[a] Connect the right speaker (located at right side of the monitor when viewed from the front) positive (+) wire to RIGHT +.  
[b] Connect the right speaker negative () wire to RIGHT -.  
[c] Connect the left speaker negative () wire to LEFT.  
[d] Connect the left speaker positive wire (+) to LEFT+.  
*Not included  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup and connections  
A QUICK TOUR OF THE REMOTE CONTROL  
In alphabetical order  
ON•OFF  
VCR  
1
MONITOR  
ANTENNA In HD RCVR mode, switches the HD receiver between  
antenna A and antenna B.  
DVD VCR2  
MUTE  
AUX HD RCVR  
Arrows Use the arrows to navigate through the menu screens.  
WHO•MULTI  
AUX (auxiliary) You can program this button to control any one of the  
following: a cable box; most GE, RCA, and PROSCAN audio components;  
a laserdisc player; a VCR; or a satellite receiver. Press this button to operate  
the component youve programmed to work with the AUX button.  
H
CH+/CHChanges channels on the HD receiver when the remote is in  
HD receiver mode. When the Zoom mode is active, zooms in (CH+) or out  
(CH-).  
M
SLEEP  
GUIDE  
GO BACK  
INFO  
CINEMA Press to select one of four screen sizes to suit the type of input  
youre watching.  
OK  
O
NOTE: When watching the HD receiver, screen size is controlled  
through the HD receiver menu system.  
CLEAR  
MENU  
CLEAR Clears on-screen displays and returns you to normal viewing.  
3
1
4
2
CMPNT Toggles between CMPNT1 and CMPNT2 inputs.  
5
8
6
GO BACK In HD receiver mode, returns you to the previous channel.  
When in the menu system, returns you to the previous menu.  
9
7
INPUT  
ANTENNA  
0
GUIDE In HD receiver mode, brings up the on-screen program guide.  
INFO Brings up channel information.  
REVERSE  
RECORD  
PLAY FORWARD  
STOP  
PAUSE  
INPUT Changes the video input.  
CINEMA RGB  
CMPNT VIDEO  
MENU Brings up the on-screen menu.  
MONITOR Turns the power to the monitor on and puts the remote in  
Monitor mode so you are able to control the Cinema Screen display.  
SOURCE  
u
n
i
v
e
r
s
a
l
MUTE Reduces sound to an inaudible level.  
Numbers Use the number keys to make numerical entries.  
OK/ZOOM When in Monitor mode (press the MONITOR button) and  
using on-screen menus, press OK to select a highlighted menu function.  
When there are no on-screen menus displayed, press OK to bring up the  
zoom pointer. Position pointer on the part of the screen you want to zoom  
on, then use the CH+/- buttons to zoom in/out.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup and connections  
ONOFF Toggles power on and off for the components that you have  
programmed. For example, if you are in VCR mode, turns VCR on and off.  
ONOFF  
VCR  
1
MONITOR  
REVERSE, PLAY, FORWARD, STOP, PAUSE, RECORD (transport keys) Use  
with components programmed to work with your remote control (VCR,  
DVD player, audio components).  
DVD VCR2  
MUTE  
AUX HD RCVR  
RGB Depending on how you set up the Cinema Screen monitor, toggles  
WHOMULTI  
between RGB1, RGB2*, and RGB3.  
*Note: You can set up CMPNT1 OR RGB2, but not both. If CMPNT1 is  
set up, RGB2 will not appear when you use the RGB button.  
H
SLEEP Brings up the sleep timer, which is used to turn the monitor off  
automatically after a set amount of time.  
M
SLEEP  
GUIDE  
GO BACK  
INFO  
VCR1, VCR2, DVD, HD RCVR, MONITOR These are the component  
buttons used to put the remote control into the correct mode to operate  
that particular component. The correct video source must first be selected  
(VIDEO or RGB) or Autotuning must be set up.  
OK  
O
VOL /VOL  
Adjusts the volume.  
CLEAR  
MENU  
3
VIDEO Selects whatever component is hooked up to the video source  
inputs.  
1
4
2
5
8
6
WHOMULTI Brings up personal viewer profiles for some components.  
9
7
ZOOM IN When in zoom mode (press the MONITOR button an then the  
OK button to access zoom mode) enlarges the picture. When in zoom  
mode, use the arrow buttons to pan and scan the entire picture.  
INPUT  
ANTENNA  
0
REVERSE  
RECORD  
PLAY FORWARD  
ZOOM OUT When in zoom mode (press the MONITOR button an then  
the OK button to access zoom mode) decreases the size of the picture. If  
picture is distorted, zoom out to restore to normal.  
STOP  
PAUSE  
CINEMA RGB  
CMPNT VIDEO  
SOURCE  
u
n
i
v
e
r
s
a
l
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup and connections  
USING YOUR REMOTE CONTROL  
INSERTING BATTERIES  
1. Remove the battery compartment cover from the remote control.  
2. Insert batteries (included) as shown on the diagram inside the  
battery compartment.  
3. Replace the battery compartment cover.  
Use your remote control from a distance of about 7m/23 feet from the  
monitors remote control sensor and at a horizontal angle of within  
30°. The remote operates on line of sight, so if there is anything  
blocking the path between the remote and the remote control sensor  
on the front of the monitor, the remote may not work.  
Dont expose the remote control sensor on the front of the monitor  
to direct sunlight or strong artificial light.  
Installing the batteries  
Dont get the remote control wet.  
Avoid heat and humidity.  
When not using the remote for a long period of time, remove the  
batteries.  
PROGRAMMING THE REMOTE  
The universal remote control that came with your Cinema Screen  
monitor is already programmed to operate most RCA, GE, and  
PROSCAN VCRs, DVD players, laserdisc players, and satellite  
receivers. This remote is also capable of operating many other brands  
of remote-controllable electronic components, but you must program  
it to do so.  
POWER STANDBY  
INPUT SELECT  
VOLUME  
FIND OUT IFY OU NEED TO PROGRAM THE REMOTE  
To determine whether the universal remote needs to be programmed,  
turn on one of your components, such as a VCR. Point the remote  
control at the component and press the component button (for  
example, the VCR button). Now press the ONOFF button on the  
remote. If the component doesnt turn off, you need to program the  
remote control in order for it to operate that component.  
Approx.  
7m/23 ft.  
30° 30°  
VCR1  
ON OFF  
MONITOR  
DVD VCR2 AUX SAT CABLE  
MUTE  
WHO  
C
+
V
L
L
V
C
H
-
Z
ZZ  
SLEEP  
GO BACK  
INFO  
GUIDE  
OK  
MENU  
CLEAR  
1
4
7
2
5
8
0
3
6
9
INPUT  
ANTENNA  
REVERSE  
PLAY  
FORWARD  
RECORD  
STOP  
PAUSE  
C
I
N
E
M
A
V
G
A
Y
u
v
VIDEO  
SOURCE  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup and connections  
HOW TO PROGRAM THE REMOTE  
There are two ways to program the remote control: automatic code search  
and direct entry.  
USING AUTOMATIC CODE SEARCH  
1. Turn on the component you want the remote to operate (VCR, HD  
receiver, etc.)  
2. Press and hold the component button that corresponds to the  
component you want the remote to operate (VCR, HD receiver,, etc.).  
While you hold down the component button, press and hold ONOFF  
(when the red light on the remote turns on, release both buttons).  
3. Press PLAY (the red light on the remote starts flashing).  
The remote is searching the first set of component codes (there are  
several sets of codes). If the component you want to operate doesnt  
turn off automatically after 5 seconds, press PLAY again (the red light  
starts flashing again as the remote searches through the next set of  
codes).  
Continue pressing PLAY until the component turns off.  
ONOFF  
VCR  
1
MONITOR  
NOTE: If the component doesnt turn off after youve pressed the PLAY  
button 20 times, the component cant be programmed.  
DVD VCR2  
AUX HD RCVR  
4. Press REVERSE and wait 2 seconds. Repeat this step until the  
component turns back on.  
5. To finish, press and hold the STOP button until the red light on the  
remote turns off.  
Component Buttons  
These are the buttons you program to operate another  
component.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup and connections  
USING DIRECT ENTRY  
1. Turn on the component you want the remote to operate (the red light  
on the remote turns on).  
2. Look up the brand and code number(s) for the component on the code  
list on the following pages.  
3. Press and hold the component button that corresponds to the  
component you want the remote to operate (VCR, DVD, etc.).  
4. Enter the code from the code list. When you begin entering numbers,  
the red light on the remote turns off. When the last number is entered,  
the red light turns back on. If the incorrect code is entered, the red  
light will flash.  
5. Release the component button. The red light on the remote turns off.  
6. Press ONOFF to see if the component responds to the remote  
commands. If it doesnt, try pressing the component button and then  
ONOFF again.  
6. If you get no response, repeat these steps using the next code listed for  
your brand, until the component responds to the remote commands.  
HOW TO USE THE REMOTE CONTROL AFTER YOUVE  
PROGRAMMED IT  
Once the remote control has been programmed successfully, youre ready  
to use it to operate other components.  
1. Press one of the video source buttons to select a component (VIDEO or  
RGB) to operate.  
2. Press the component button (MONITOR, VCR, DVD, AUX, or HD  
RCVR) to use the Transport buttons (REVERSE, PLAY, FORWARD,  
STOP, PAUSE, and RECORD) to operate the component.  
3. Press ONOFF to turn the component on or off.  
NOTE: If you keep pressing buttons and nothing happens, you may  
have the wrong video source or wrong component selected. You must  
press the correct video source and the component button that matches  
the component you want to operate.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
setup and connections  
PROGRAMMABLE CODES FOR THE REMOTE CONTROL  
VCR  
Magnavox .......... 2021, 2022, 2062, 2063, 2104,  
2108, 2124  
Sylvania .... 2002, 2021, 2022, 2026, 2062, 2063,  
2065, 2124  
Admiral ........................................................ 2131  
Magnin ........................................................ 2013  
Symphonic ......................................... 2002, 2026  
Tandy ................................................. 2002, 2011  
Tashiko ........................................................ 2014  
Tatung ............................................... 2058, 2111  
TEAC .................... 2002, 2026, 2058, 2085, 2111  
Technics ............................................. 2021, 2109  
Teknika ...... 2002, 2014, 2021, 2026, 2100, 2129  
TMK ......................................... 2013, 2024, 2047  
Toshiba2015, 2049, 2051, 2055, 2065, 2093, 2116  
ToteVision.......................................... 2013, 2014  
Unitech ........................................................ 2013  
Vector Research ............ 2009, 2010, 2015, 2016  
Victor ........................................................... 2010  
Video Concepts ... 2009, 2010, 2015, 2016, 2113  
Videosonic ................................................... 2013  
Wards ....... 2002, 2013, 2014, 2015, 2021, 2023,  
2026, 2029, 2055, 2056, 2061, 2096, 2101, 2102,  
2103, 2107, 2116, 2131  
Adventura ................................................... 2026  
Marantz .... 2009, 2010, 2011, 2016, 2018, 2021,  
Aiko ............................................................. 2027  
2058, 2062,2064  
Aiwa .................................................. 2002, 2026  
Marta ........................................................... 2014  
Akai 2003, 2004, 2005, 2007, 2008, 2111, 2112,  
Masushita .................................................... 2021  
2113  
MEI............................................................... 2021  
American High ............................................ 2021  
Memorex ............ 2002, 2011, 2013, 2014, 2021,  
Asha ............................................................. 2013  
2023, 2026, 2104, 2131  
Audio Dynamics ................................ 2009, 2010  
MGA ........................................ 2029, 2065, 2113  
Audiovox ..................................................... 2014  
MGN Technology ........................................ 2013  
Bell & Howell .............................................. 2011  
Midland ....................................................... 2053  
Beaumark .................................................... 2013  
Minolta .................................... 2055, 2056, 2107  
Broksonic ........................................... 2012, 2025  
Mitsubishi ........... 2029, 2055, 2056, 2065, 2066,  
Calix ............................................................. 2014  
2067, 2069, 2070, 2071, 2072, 2073, 2074, 2106,  
2113, 2123  
Candle2013, 2014, 2015, 2016, 2017, 2018, 2019  
Canon ...................................... 2021, 2022, 2114  
Capehart............................................ 2020, 2110  
Carver .......................................................... 2062  
CCE..................................................... 2027, 2061  
Citizen ..... 2013, 2014, 2015, 2016, 2017, 2018,  
2019, 2027  
Montgomery Ward ........................... 2075, 2131  
Motorola ........................................... 2021,2131  
MTC ......................................... 2002, 2013, 2026  
Multitech ... 2002, 2013, 2016, 2026, 2053, 2061  
NEC ........... 2009, 2010, 2011, 2016, 2018, 2058,  
2064, 2076, 2078, 2079, 2111, 2123  
XR-1000 ................................... 2021, 2026, 2061  
Yamaha ..... 2009, 2010, 2011, 2018, 2058, 2111  
Zenith .................. 2004, 2098, 2104, 2119, 2128  
Colortyme .................................................... 2009  
Colt .............................................................. 2061  
Craig .............................. 2013, 2014, 2023, 2061  
Curtis-Mathes2000, 2002, 2009, 2013, 2016, 2018,  
2021, 2022, 2024, 2115  
Cybernex ..................................................... 2013  
Daewoo2015, 2017, 2019,2025, 2026, 2027, 2028,  
2110  
Nikko ........................................................... 2014  
Noblex ......................................................... 2013  
Olympus ...................................................... 2021  
Optimus ............................................. 2014, 2131  
Optonica...................................................... 2096  
Orion ........................................................... 2035  
Panasonic .. 2021, 2022, 2109, 2125, 2126, 2127  
Pentax .................. 2016, 2055, 2056, 2107, 2120  
Pentex Research .......................................... 2018  
Philco ............................. 2021, 2022, 2062, 2063  
Philips ............................ 2021, 2062, 2096, 2124  
Pilot ............................................................. 2014  
Pioneer ................ 2010, 2055, 2080, 2081, 2123  
Portland......................... 2016, 2017, 2019, 2110  
PROSCAN ........................................... 2000, 2001  
Protec .......................................................... 2061  
Pulsar ........................................................... 2104  
Quarter ........................................................ 2011  
Quartz ......................................................... 2011  
Quasar ..................................... 2021, 2022, 2125  
RCA 2000, 2001, 2003, 2013, 2021, 2055, 2056,  
2082, 2083, 2084, 2085, 2086, 2087, 2088, 2089,  
2090, 2091, 2107, 2115, 2120, 2125  
CABLE BOX  
ABC .. 5002, 5003, 5004, 5005, 5006, 5007, 5053  
Antronix ............................................ 5008, 5009  
Archer ............................ 5008, 5009, 5010, 5011  
Cabletenna .................................................. 5008  
Cableview .................................................... 5008  
Century ........................................................ 5011  
Citizen ......................................................... 5011  
Colour Voice ...................................... 5012, 5013  
Comtronics ........................................ 5014, 5015  
Contec ......................................................... 5016  
Eastern ......................................................... 5017  
Garrard ........................................................ 5011  
GC Electronics ............................................. 5009  
Gemini ..................................... 5018, 5019, 5049  
General Instrument .................................... 5003  
Hamlin ................. 5020, 5021, 5022, 5035, 5045  
Hitachi ......................................................... 5003  
Hytex ........................................................... 5002  
Jasco ............................................................ 5011  
Jerrold ....... 5003, 5005, 5007,5018, 5023, 5024,  
5046, 5053  
Magnavox ................................................... 5025  
Memorex ..................................................... 5026  
Movie Time.............................. 5002, 5027, 5028  
NSC .......................................... 5002, 5027, 5028  
Oak ........................................... 5002,5016, 5029  
Panasonic .......................................... 5048, 5052  
Paragon ....................................................... 5026  
Philips ....... 5011, 5012, 5013, 5019, 5025, 5030,  
5031, 5032  
Daytron ....................................................... 2110  
Dbx .................................................... 2009, 2010  
Dimensia...................................................... 2000  
Dynatech ........................................... 2002, 2026  
Electrohome ...................................... 2014, 2029  
Electrophonic .............................................. 2014  
Emerson2002, 2012,2014, 2015, 2021, 2024, 2025,  
2026, 2029, 2030, 2032, 2033, 2034, 2035, 2036,  
2037, 2038, 2039, 2040, 2041, 2042, 2044, 2045,  
2047, 2065, 2105, 2113, 2116, 2117, 2130  
Fisher ........ 2011, 2023, 2048, 2049, 2050, 2051,  
2052,2118  
Fuji ..................................................... 2021, 2119  
Funai .................................................. 2002, 2026  
Garrard ........................................................ 2026  
GE2000, 2001, 2013, 2021, 2022, 2053, 2115, 2120  
Goldstar ............... 2009, 2014, 2018, 2054, 2121  
Gradiente .................................................... 2026  
Harley Davidson .......................................... 2026  
Harman Kardon .......................................... 2009  
Harwood ..................................................... 2061  
Headquarter ................................................ 2011  
Hitachi ...... 2002, 2055, 2056, 2057, 2107, 2111,  
2120, 2122  
HI-Q ............................................................. 2023  
Instant Replay ............................................. 2021  
JCL................................................................ 2021  
JC Penney 2009, 2010, 2011, 2013, 2014, 2021,  
2022, 2055, 2056, 2058, 2059, 2060, 2107, 2118  
Jensen ...................................... 2055, 2056, 2111  
JVC ... 2009, 2010, 2011, 2018, 2058, 2111, 2123  
Kenwood ............ 2009, 2010, 2011, 2016, 2018,  
2058, 2111,2123  
KLH .............................................................. 2061  
Kodak ................................................ 2014, 2021  
Lloyd .................................................. 2002, 2026  
Logik ............................................................ 2061  
LXI ................................................................ 2014  
Radio Shack/Realistic .... 2002, 2011, 2013, 2014  
2021, 2022, 2023, 2026, 2029, 2049, 2050, 2096,  
2131  
Radix ............................................................ 2014  
Randex ......................................................... 2014  
Ricoh ............................................................ 2128  
Runco........................................................... 2104  
Samsung .... 2005, 2013, 2015, 2033, 2053, 2112  
Sanky ................................................. 2131, 2104  
Sansui ............................ 2010, 2092, 2111, 2123  
Sanyo ....................................... 2011, 2013, 2023  
Scott 2012, 2015, 2025, 2032, 2035, 2038, 2065,  
2093, 2116  
Pioneer .............................................. 5033, 5034  
Pulsar ........................................................... 5026  
RCA .......................................... 5047, 5049, 5052  
Realistic ............................................. 5009, 5049  
Regal.................................................. 5022, 5035  
Regency ....................................................... 5017  
Rembrandt .................................................. 5003  
Runco........................................................... 5026  
Samsung ............................................ 5014, 5034  
Scientific Atlanta .......... 5006, 5036, 5037, 5038  
Signal ................................................. 5014, 5018  
Sears2011, 2014, 2021, 2023, 2048, 2049, 2050,  
2051, 2055, 2056, 2107, 2118  
Sharp 2002, 2017, 2029, 2094, 2095, 2096, 2131  
Shintom ......................... 2004, 2056, 2061, 2098  
Shogun ........................................................ 2013  
Signature .......................................... 2002, 2131  
Singer ...................................... 2021, 2061, 2128  
Sony ........... 2002, 2004, 2098, 2099, 2119, 2128  
STS ..................................................... 2021, 2107  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setup and connections  
Signature ..................................................... 5003  
SATELLITE RECEIVER  
AUDIO  
SL Marx ........................................................ 5014  
Sprucer ........................................................ 5052  
Starcom ................................... 5007, 5018, 5053  
Stargate ............................................. 5014, 5018  
Starquest ..................................................... 5018  
Tandy ........................................................... 5040  
Teleview ...................................................... 5014  
Tocom ...................................... 5004, 5023, 5041  
Toshiba ........................................................ 5026  
Tusa .............................................................. 5018  
TV86 ............................................................. 5027  
Unika ....................................... 5008, 5009, 5011  
United Artists .............................................. 5002  
United Cable ............................................... 5053  
Universal........................ 5008, 5009, 5010, 5011  
Videoway .................................................... 5044  
Viewstar ........................ 5015, 5025, 5027, 5040  
Zenith ...................................... 5026, 5050, 5051  
Chapparal .......................................... 5056, 5057  
Drake ................................................. 5058, 5059  
GE ...................................................... 5000, 5001  
General Instuments ................ 5060, 5061, 5062  
Panasonic .................................................... 5075  
Primestar ..................................................... 5076  
PROSCAN ........................................... 5000, 5001  
RCA .................................................... 5000, 5001  
Realistic ....................................................... 5063  
Sony ............................................................. 5072  
STS1 ............................................................. 5064  
STS2 ............................................................. 5065  
STS3 ............................................................. 5066  
STS4 ............................................................. 5067  
Toshiba ........................................................ 5068  
Toshiba ........................................................ 5073  
Uniden ......................................................... 5069  
(For RCA and Dimensia brands only)  
AM/FM ......................................................... 4003  
Aux .............................................................. 4004  
Phono .......................................................... 4005  
CD ................................................................ 4007  
Tape ............................................................. 4006  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
This page intentionally left blank.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
setup and  
connections  
1
GETTING AROUND THE MENU SYSTEM  
There are several functions available for customizing the  
Cinema Screen monitor to suit your viewing environment.  
The Cinema Screen monitor’s on-screen menu system  
makes controlling the functions of your monitor simple.  
The menu system  
2
3
reference  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
BASIC OPERATIONS  
POWER  
To turn the monitor on and off:  
1. Plug the power cord into an active AC power outlet.  
2. Press the ON•OFF button on the remote control or the unit. The  
monitor’s POWER/STANDBY indicator turns green when the monitor  
is on.  
3. Press the ON•OFF button on the remote control or the unit to turn it  
off. The monitor’s POWER/STANDBY indicator turns red and the  
standby mode is set (only when turning off the unit with the remote  
control).  
VOLUME  
To adjust the volume:  
1. Press and hold the VOL  
button (on the remote control or the unit)  
to increase to the desired level.  
2. Press and hold the VOL  
button (on the remote control or the unit)  
to decrease to the desired level.  
Note: External speakers are required for sound.  
MUTE  
Press the MUTE button on the remote control to reduce the sound to an  
inaudible level. Press MUTE again to restore the sound.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
NAVIGATING THE MENUS  
You can adjust monitor options through the Cinema Screen monitors  
menu system. To access the main menu, press the MENU button on the  
remote control or MENUOK on the front of the monitor.  
GUIDE  
INFO  
OK  
O
There are a few things you need to know to navigate through the menu  
system. The navigation buttons are the set of arrow-shaped buttons in the  
middle of the remote (See illustration on right).  
CLEAR  
MENU  
Use the and buttons on the remote to move the menu highlight up and  
down.  
These are the buttons on the remote  
you use to navigate through the  
monitor’s on-screen menu system.  
Use the and buttons to move the highlight and change settings.  
Press the GO BACK button on the remote to return to a previous menu.  
You can return the Cinema Screen monitor to the factory settings at any  
time by using the RESET option in the OPTIONS menu. Remember, if you  
choose to reset, ALL settings will return to the factory settings.  
ON-SCREEN MENU OPERATION  
To access the main menu, press the MENU button on the remote. The  
MAIN MENU is displayed on the screen. The main menu contains a list of  
all the menus that control your monitor. To select a menu, use the up/down  
arrow buttons on the remote to highlight the desired menu. When the  
desired menu is highlighted, press the OK or MENU button to select.  
MAIN MENU  
PICTURE QUALITY  
AUDIO  
SCREEN  
Note: Different components use different types of input (RGB,  
video, etc). Some menu options apply to only one type of input, so  
they only appear when they apply to the currently active input. For  
example, the COLOR and TINT options in the PICTURE QUALITY  
menu only appear when you are adjusting standard video input  
(VIDEO1, VIDEO2, VIDEO3).  
FUNCTION  
OPTIONS  
SETUP  
AUTOTUNING SETUP  
SEL.  
OK  
EXIT  
This is the main menu with the PICTURE Quality  
option highlighted. Press OK to bring up the  
highlighted menu.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
THE PICTURE QUALITY MENU  
SETTING THE PICTURE MODE  
The Cinema Screen monitor has preset viewing modes that can be selected  
depending on your viewing environment. Each preset mode has the  
contrast, brightness and sharpness adjusted for a specific viewing situation.  
PICTURE QUALITY  
CONTRAST  
BLACK LEVEL  
SHARPNESS  
COLOR  
MEMORY This mode allows you to set and save your own picture  
adjustments.  
R
G
TINT  
SOFT Use this mode when watching your Cinema Screen in a dark  
room. Soft mode provides a darker, finer picture, like the screen in  
movie theaters. These settings are preset for you and cant be  
changed.  
PRESETS  
: MEMORY  
: NORMAL  
: LOW  
COLOR TEMP.  
NOISE REDUCE  
BRIGHT Use this mode when watching your Cinema Screen  
monitor in a bright room. This mode provides a picture with distinct  
differences between light and dark areas. These settings are preset for  
you and cant be changed.  
ADJ.  
RETURN  
SEL.  
This is the PICTURE Quality menu with the  
PRESETS option highlighted.  
NORMAL The factory default.  
To change the picture mode:  
1. From the main menu, select PICTURE QUALITY. The PICTURE  
QUALITY Menu will appear.  
2. Highlight the PRESETS option and press the key on the remote to  
select it. The PRESETS window appears.  
3. Use the  
button on the remote to select the desired mode. The  
mode switches as follows when the button is pressed:  
PRESETS  
: SOFT  
Note: If you dont push the button within 5 seconds, the current  
selection is set and the previous screen reappears.  
This is the PRESETS screen with SOFT as the  
current selection.  
Once youve selected the desired mode, press OK or MENU. The picture  
mode is now set and you are returned to the PICTURE QUALITY screen. If  
you are using MEMORY mode, you can manually adjust the picture  
settings (contrast, black level, and sharpness). You can continue adjusting  
settings in the PICTURE QUALITY menu, return to the main menu, or exit  
the menu system.  
To return to the main menu, press the GO BACK button on the remote. To  
exit the menu system, press CLEAR.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
ADJUSTING THE PICTURE SETTINGS IN MEMORY MODE  
In MEMORY mode, you can set and save the following picture  
adjustments:  
PICTURE QUALITY  
CONTRAST  
CONTRAST Changes the pictures contrast (between light and dark).  
BLACK LEVEL Makes the picture lighter or darker.  
SHARPNESS Changes the pictures sharpness.  
COLOR Changes color density (video input only).  
TINT Changes picture tint (video input only).  
BLACK LEVEL  
SHARPNESS  
COLOR  
R
G
TINT  
PRESETS  
: MEMORY  
: COOL  
: LOW  
COLOR TEMP.  
NOISE REDUCE  
COLOR TEMP Changes the color tone.  
ADJ.  
RETURN  
SEL.  
NOISE REDUCE (noise reduction)Removes extraneous information  
from the signal to make the picture clearer.  
This is the PICTURE QUALITY menu with the  
PRESETS option highlighted.  
NOTE: Only the contrast and brightness can be adjusted when a computer  
signal is used.  
Once you have selected MEMORY mode, you can adjust the picture  
settings. For example, to change the contrast setting:  
1. Use the or button to highlight the CONTRAST option. Press the  
button to select it. The CONTRAST window appears. Use  
buttons to adjust the contrast.  
and  
NOTE: If you dont push the or button within 5 seconds, the  
current setting is accepted and the previous screen reappears.  
2. Once the contrast is adjusted, press OK or MENU. The contrast is set  
and you are returned to the PICTURE QUALITY menu.  
CONTRAST  
3. Use the same procedure to adjust the black level and sharpness  
settings.  
4. When you are finished adjusting the picture settings, press GO BACK  
to return to the main menu or press CLEAR to exit the menu system.  
This is the CONTRAST screen.  
If the CONTROL NOT AVAILABLEmessage appears when you are  
trying to change the picture settings, make sure the preset mode is set to  
MEMORY. You can only change picture settings in MEMORY mode. The  
other modes are pre-set and cant be changed.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
SETTING THE COLOR TEMPERATURE  
The color temperature setting controls how warm (red) or cool (blue) your  
picture is. The COLOR TEMP option has 4 settings:  
Normal  
Warm  
Pro (lets you select settings individually)  
Cool  
For regular viewing, Normal, Warm or Cool is recommended. The PRO  
setting is generally used only for professional applications. To change the  
COLOR TEMP setting:  
COLOR TEMP.  
: PRO  
1. From the main menu, highlight and select the PICTURE QUALITY  
menu.  
This is the COLORTEMP. screen with PRO as the  
current selection.  
2. Use the arrow buttons on the remote to highlight the COLOR TEMP  
option. Press the button to select it. The COLOR TEMP screen  
appears.  
3. Use the and buttons to select the desired COLOR TEMP setting.  
The settings switch as follows:  
WHITE BALANCE  
GAIN  
RED  
NOTE: If you dont push the or button within 5 seconds, the  
current setting is accepted and the previous screen reappears.  
GREEN  
BLUE  
BIAS  
4. Once the desired color temp is selected, press OK or MENU. If you  
choose the PRO setting, the WHITE BALANCE screen appears. It allows  
individual setting of white and dark balance for each color (red, green and  
blue).  
RED  
GREEN  
BLUE  
GAIN This adjusts the color balance for light/bright colors.  
BIAS This adjusts the color balance for dark colors.  
To change the white balance GAIN setting:  
ADJ.  
RETURN  
SEL.  
This is theWHITE BALANCE screen with the  
RED GAIN option highlighted.  
1. Highlight the RED, GREEN or BLUE GAIN option. and press the  
button. The GAIN screen for that color appears.  
2. Adjust the balance using the and keys.  
NOTE: If you dont push the or button within 5 seconds, the  
current setting is accepted and the previous screen reappears.  
3. When you have the desired setting, press OK or MENU. The GAIN is  
adjusted and you are returned to the WHITE BALANCE screen.  
4. When you completed all the desired white balance adjustments, Press  
the GO BACK button to return to the PICTURE menu. You can  
continue adjusting picture settings, return to the main menu or press  
CLEAR to exit the menu system.  
RED  
This is the R-GAIN (red gain) screen.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
REDUCING NOISE IN THE PICTURE  
Noise is a term used to describe extraneous bits of information in the signal  
that affect the clearness of the picture. You can use the Noise Reduction  
(NOISE REDUCE) setting if your reception is poor or when playing video  
tapes that have poor picture quality.  
PICTURE QUALITY  
CONTRAST  
BLACK LEVEL  
SHARPNESS  
COLOR  
The NOISE REDUCE option has four settings, including OFF. The higher  
the setting, the stronger the effect. The settings switch as follows when the  
button is pressed:  
R
G
TINT  
PRESETS  
: MEMORY  
: WARM  
: HIGH  
COLOR TEMP.  
NOISE REDUCE  
ADJ.  
SEL.  
RETURN  
To change the noise reduction setting:  
This is the PICTURE QUALITY menu with the  
NOISE REDUCE (noise reduction) option  
highlighted.  
1. From the PICTURE QUALITY menu, highlight the NOISE REDUCE  
option, and select it by pressing the button. The NOISE REDUCE  
SCREEN is displayed.  
2. Use the and buttons to select the desired noise reduction setting.  
NOTE: If you dont push the or button within 5 seconds, the  
current setting is accepted and the previous screen reappears.  
3. When the desired setting is displayed, press OK to return to the  
PICTURE QUALITY menu. You can continue adjusting picture  
settings, return to the main menu, or press CLEAR to exit the menu  
system.  
NOISE REDUCE  
: HIGH  
This is the NOISE REDUCE (noise reduction)  
screen.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
THE AUDIO MENU  
The AUDIO menu allows you to adjust the treble, bass and left/right  
balance of your external speakers.  
AUDIO  
BASS  
TREBLE  
BALANCE  
BASS Changes the level of low frequency sound.  
L
R
TREBLE Changes the level of high frequency sound.  
BALANCE Changes the balance of the left and right speakers.  
MENU OPERATIONS  
To access the AUDIO menu:  
ADJ.  
SEL.  
RETURN  
1. From the main menu, highlight and select the AUDIO option. The  
AUDIO menu is displayed.  
This is the AUDIO menu with the BASS option  
highlighted. Press the rightarrow button to  
select it.  
2. Use the and arrow buttons on the remote to highlight an option  
(for example, BASS).  
3. Use the and buttons to adjust to the desired setting.  
4. You can continue adjusting audio settings, press GO BACK to return  
to the main menu, or press CLEAR to exit the menu system.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
THE SCREEN MENU  
The SCREEN menu allows you to set the monitor to automatically select  
the correct mode for viewing a particular movie and to change the  
positions of on-screen menus.  
SELECTING AV IEWING SIZE  
When viewing with a component other than your HD receiver, you can set  
the screen mode to one of four screen sizes to suit the type of input you are  
watching. Select the screen mode with the CINEMA button on the remote  
control. The screen sizes are as follows:  
FILL expands in both vertical and horizontal directions while the correct  
proportions are maintained. The picture is not distorted, just closer.  
NORMAL displays a picture with a 4:3 aspect ratio (standard video).  
Because this mode fills the screen vertically, but not horizontally, black  
bars will appear on the right and left sides of the picture.  
Fill  
Note: If viewing with a 4/3 aspect ratio for long periods of time,  
set side gray level at 3 or 4.  
FULL expands the picture in the horizontal direction only. This option  
corrects the aspect ratio of images that have been compressed or  
squeezed.”  
STADIUM expands in both the horizontal and vertical directions, but  
varies the amount of stretch depending on the picture the center of the  
picture is almost normal while the edges are considerably expanded. This  
mode is intended for watching video with a 4:3 aspect ratio on a wide  
screen.  
Normal  
Note: In stadium mode, only the V-position and H-position are  
displayed. You cant change the height and width.  
To change the viewing size:  
1. Press the CINEMA button on the remote control.  
2. The current viewing size will be displayed. Press the CINEMA button  
again to switch to the next size. The size switches as follows:  
Full  
Stadium  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
ADJUSTING THE PICTURE POSITION AND SIZE  
The SCREEN menu lets you adjust the position and size of the picture.  
SCREEN  
The first two options, V-POSITION and H-POSITION, adjust the placement  
of the picture on the screen. For example, if the picture is too far to the left,  
you can use the H-POSITION to move it to the right.To adjust the position  
of the picture on the screen:  
MODE  
: NORMAL  
V-POSITION  
H-POSITION  
V-HEIGHT  
H-WIDTH  
1. From the main menu, highlight and select the SCREEN option. The  
SCREEN menu is displayed.  
2. Use the and buttons to select the mode you want to change.  
3. When the desired mode is highlighted, press the button. The  
selected mode screen will be displayed.  
ADJ.  
SEL.  
RETURN  
The SCREEN menu with the MODE option  
highlighted.  
Use the arrow buttons to adjust the position of the picture.  
NOTE: If you dont push the an arrow button within 5 seconds, the  
current setting is accepted and the previous screen reappears.  
4. When youve adjusted to the desired setting, press the GO BACK  
button on the remote to return to the SCREEN menu.  
The V-HEIGHT and H-WIDTH options expand and contract the size of the  
picture to fill the screen. For example, if the picture is slightly wider than  
the screen, you can use the H-WIDTH option to shrink the picture  
horizontally.  
Note: These options are not available in STADIUM mode.  
To adjust the screen size:  
1. Select the desired option from the screen menu and press the  
button. The selected mode window will be displayed.  
2. Use the arrow buttons to adjust the size of the picture.  
NOTE: If you dont push an arrow button within 5 seconds, the  
current setting is accepted and the previous screen reappears.  
3. When youve adjusted to the desired setting, press OK to select and  
return to the SCREEN menu.  
SCREEN  
MODE  
: FULL  
V-POSITION  
H-POSITION  
V-HEIGHT  
H-WIDTH  
AUTO PICTURE  
The AUTO PICTURE function appears in the SCREEN menu only if you  
have a computer connected to the Cinema Screen display. When this  
feature is turned on, it automatically adjusts flickering and striped patterns  
in a computer image. If you want to adjust these manually:  
AUTO PICTURE  
FINE PICTURE  
PICTURE ADJ.  
: OFF  
1. Select the AUTO PICTURE option from the SCREEN menu. Press the  
button to turn AUTO PICTURE off. When AUTO PICTURE is  
turned off, the FINE PICTURE and PICTURE ADJ. options are  
displayed beneath it.  
ADJ.  
SEL.  
RETURN  
The AUTO PICTURE option only appears if  
you have a computer connected.  
2. Select an option and press the button. The screen for that option  
will be displayed. Use the and buttons to adjust that option.  
Press OK to return to the SCREEN menu.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
THE FUNCTION MENU  
The FUNCTION menu contains options that control on-screen displays  
(other than the menu system) and how the picture is displayed.  
FUNCTION  
: ON  
DISPLAY  
MENU ADJUST  
: 1  
ON-SCREEN DISPLAYS  
POWER SAVER : OFF  
On-screen displays (different than the menu system) appear by default to  
give you information about an option you have selected. For example,  
When you switch inputs the currently selected input name (for example,  
CMPNT1) is displayed on the screen. To turn on-screen displays off:  
GRAY LEVEL  
: 3  
PLE+INVERSE  
: AUTO  
RESET  
1. From the main menu, highlight and select the FUNCTION option.  
The FUNCTION menu is displayed.  
ADJ.  
RETURN  
SEL.  
2. Highlight and select the DISPLAY option. Use the button to toggle  
on-screen displays on or off.  
Note: Turning the DISPLAY option off does not affect on-screen  
menus. Menus cant be turned off.  
FUNCTION  
: ON  
3. You can continue setting options in the FUNCTION menu, press GO  
BACK to return to the main menu, or press CLEAR to exit the menu  
system.  
DISPLAY  
MENU ADJUST  
: 2  
POWER SAVER : OFF  
GRAY LEVEL  
PLE+INVERSE  
FILM MODE  
RESET  
: 3  
ADJUSTING THE POSITION OF THE MENU DISPLAY  
The on-screen menus can de displayed in different positions on the screen.  
There are a total of nine possible positions shown in the grid on the right.  
: AUTO  
: AUTO  
To adjust the position of the on-screen menus:  
ADJ.  
SEL.  
RETURN  
1. From the main menu, highlight and select the FUNCTION option.  
The FUNCTION menu is displayed.  
2. Highlight and select the MENU ADJUST option. Use the button to  
scroll through the menu positions As you press the button, the  
menu will move around to the different positions.  
3. When you have the menu in the desired position you can press the ➣  
or arrow to select another option in the FUNCTION menu, press  
GO BACK to return to the main menu, or press CLEAR to exit the  
menu system.  
1 2 3  
4 5 6  
7 8 9  
The number 2 position will display on-screen  
menus in the top center of your screen.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
SETTING THE POWER SAVER FOR COMPUTER IMAGES  
The POWER SAVER function can be used when the signal source to the  
monitor comes from a computer conforming to the VESA DPMS format.  
This function automatically reduces the monitors power consumption if  
no operation is performed for a certain amount of time. POWER SAVER  
can be turned on or off.  
FUNCTION  
: ON  
DISPLAY  
MENU ADJUST  
: 1  
POWER SAVER : ON  
GRAY LEVEL  
PLE+INVERSE  
FILM MODE  
RESET  
: 3  
If the computers power isnt turned on or if the computer and selector  
tuner are not properly connected, POWER SAVER is set to OFF.  
: AUTO  
: AUTO  
For instructions on using the computers power management function, see  
your computers operating manual.  
To turn the Cinema Screens POWER SAVER function on or off:  
ADJ.  
SEL.  
RETURN  
1. From the main menu, highlight and select FUNCTION. The  
FUNCTION menu is displayed.  
This is the FUNCTION menu with the  
POWER SAVER option highlighted.  
2. Highlight the POWER SAVER option.  
3. Use the button to toggle the setting ON or OFF.  
4. You can continue making adjustments in the FUNCTION menu,  
return to the previous menu by pressing the GO BACK button or  
press CLEAR to exit the menu system.  
The POWER/STANDBY indicator shows the status of the POWER SAVER  
function. See below for status and description.  
POWER/STANDBY INDICATOR  
POWER  
SAVER  
Mode  
POWER/  
STANDBY  
indicator  
Power Saver  
Operating Status  
Description  
Turning the Picture Back On  
Picture already on.  
On  
Green  
Yellow  
Red  
Not activated  
Activated  
Horizontal and vertical  
synchronizing signals are  
present from the computer.  
Standby  
Suspend  
Off  
No horizontal synchronizing  
signals are present from the  
computer.  
Use the keyboard or mouse.  
The picture reappears immediately.  
Activated  
No vertical synchronizing signals  
are present from the computer.  
Use the keyboard or mouse. The  
picture reappears, but more slowly  
than when in standby mode.  
Red  
Activated  
No horizontal and vertical  
synchronizing signals are present  
from the computer.  
Use the keyboard or mouse. The  
picture reappears, but more slowly  
than when in either standby or  
suspend mode.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
SETTING THE GRAY LEVEL FOR THE SIDES OF THE SCREEN  
The GRAY LEVEL function allows you to set the gray level for the sides of  
the screen where nothing is displayed (on the left and right sides of the  
screen when it is set to 4:3 size). The level can be adjusted from 0 to 15.  
The factory setting is 3 (dark gray).  
FUNCTION  
: ON  
DISPLAY  
MENU ADJUST  
: 1  
POWER SAVER : OFF  
NOTE: Repeated watching with the gray level set to black may  
effect the quality of your picture. To reduce the effects of uneven  
phosphor aging, set the gray level to 3 or 4.  
GRAY LEVEL  
: 9  
PLE+INVERSE  
: AUTO  
To adjust the gray level for the sides of the screen:  
RESET  
1. From the main menu, highlight and select FUNCTION. The  
FUNCTION menu is displayed.  
ADJ.  
SEL.  
RETURN  
2. Highlight the GRAY LEVEL option.  
This is the FUNCTION menu with the GRAY  
LEVEL option highlighted.  
3. Use the button to scroll through the levels.  
4. When the desired gray level is highlighted, press the button to  
return to the FUNCTION menu options. You can continue making  
adjustments within the FUNCTION menu, press GO BACK to return  
to the previous menu or press CLEAR to exit the menu system.  
NOTE: Repeated watching with the  
gray level set to black may effect the  
quality of your picture. To reduce the  
effects of uneven phosphor aging, set  
the gray level to 3 or 4.  
SETTING THE BRIGHTNESS LEVEL WITH THE  
PLE+INVERSE  
The PLE+INVERSE option contains two features in one. These features are  
used principally for PC operation.  
If viewing with a 4/3 aspect ratio for  
long periods of time, set side gray  
level at 3 or 4.  
The PLE (Peak Luminance Enhancement) function sets the luminance level  
to a fixed mode to reduce the effects of phosphor aging.  
The INVERSE function works in RGB mode only. INVERSE inverts the video  
signal, playing the image in a negative format.  
FUNCTION  
PLE+INVERSE has four options:  
DISPLAY  
: ON  
: 1  
AUTO luminance level (contrast) is normal.  
AUTO+ON normal contrast with inverse activated.  
LOCK dims picture to reduce phosphor aging.  
MENU ADJUST  
POWER SAVER : OFF  
GRAY LEVEL  
PLE+INVERSE  
FILM MODE  
RESET  
: 3  
: LOCK  
: AUTO  
LOCK+ON dims picture to reduce phosphor aging with inverse  
activated.  
The factory setting is AUTO. Setting the PLE+INVERSE option to LOCK  
dims the picture the contrast will be lower than normal.  
ADJ.  
RETURN  
SEL.  
To set the PLE level to LOCK:  
This is the FUNCTION option with the  
PLE+INVERSE option highlighted.  
1. From the main menu, highlight and select FUNCTION. The  
FUNCTION menu is displayed.  
2. Highlight the PLE+INVERSE option.  
3. Use the button to select LOCK.  
Setting PLE+INVERSE to LOCK is  
recommended if you are displaying  
stationary pictures.  
4. Press the button to return to the FUNCTION menu options. You  
can continue making adjustments within the FUNCTION menu,  
return to the previous menu or press MENU or CLEAR to exit the  
menu system.  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
ADJUSTING FOR FLICKERING WITH FILM MODE  
There is some amount of flickering that occurs in an image when it is  
transfered from film to video. Setting the Film Mode option to Auto will  
reduce flickering and improve the quality of video images.  
FUNCTION  
: ON  
DISPLAY  
MENU ADJUST  
: 1  
AUTO The display will recognize and correct any flickering that occurs in  
an image.  
POWER SAVER : OFF  
GRAY LEVEL  
PLE+INVERSE  
FILM MODE  
RESET  
: 3  
ON All images are displayed in film mode.  
OFF Film mode is off.  
: AUTO  
: ON  
To turn FILM MODE to AUTO:  
1. From the main menu, highlight and select FUNCTION. The  
FUNCTION menu is displayed.  
ADJ.  
RETURN  
SEL.  
This is the FUNCTION menu with the FILM  
MODE option highlighted.  
2. Highlight the FILM MODE option.  
3. Use the button to scroll through the three modes until the AUTO is  
displayed.  
4. Press the button to return to the FUNCTION menu optons. You can  
continue making adjustments within the FUNCTION menu, return to  
the previous menu by pressing GO BACK or press CLEAR to exit the  
menu system.  
RESET  
RESETTING TO DEFAULTV ALUES  
The RESET function allows you to reset all adjustments to the factory  
default settings. Remember, this will reset all adjustments you have made  
in all menus.  
RESET  
RETURN  
To reset to the factory default settings:  
1. From the main menu, highlight and select OPTIONS. The OPTIONS  
menu is displayed.  
2. Highlight the RESET function and press OK.  
3. The RESET screen is displayed.  
SEL.  
RETURN  
OK  
4. Use the or button to highlight the RESET option and press OK or  
MENU. The RESET screen will display the message NOW  
RESETTING. When the settings are restored to the factory default you  
are returned to the RESET screen.  
RESET  
When you are done, press GO BACK to return to the FUNCTION menu or  
pres CLEAR to exit the menu system.  
NOW RESETTING  
These are the RESET screens. Choose the  
RESET option if you want to reset ALL options  
in all menus back to the factory default.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
THE OPTIONS MENU  
SETTING THE AUDIO INPUTS  
OPTIONS  
AUDIO INPUT  
The Cinema Screens audio sources are programmable to the each of the  
displays video sources. For example, you can program AUDIO1 source to  
work with the RGB2 video source.  
AUDIO1  
: RGB1  
: VIDEO1  
: CMPNT1  
: RGB2  
: RGB  
This feature is generally used only for commercial applications.  
AUDIO2  
AUDIO3  
1. From the main menu, highlight and select OPTIONS. The OPTIONS  
menu is displayed.  
BNC SELECT  
RGB SELECT  
HD SELECT  
RGB3 ADJUST  
2. Highlight the one of the audio input options.  
: 1080A  
: 1  
3. Use the button to scroll through the available video sources. The  
modes scroll as follows:  
SEL.  
ADJ.  
RETURN  
This is the OPTIONS menu with the AUDIO1  
input option highlighted.  
4. When the desired mode is selected, press the button to return to  
the OPTIONS menu items. You can continue making adjustments  
within the OPTION menu, press GO BACK to return to the previous  
menu or press MENU or CLEAR to exit the menu system.  
OPTIONS  
SETTING THE BNC CONNECTORS  
By default, the BNC inputs are set to RGB1, or composite video. If the  
component you are connecting to the BNC jacks doesnt have composite  
video jacks, you can set the BNC inputs to act as component video.  
AUDIO INPUT  
AUDIO1  
: RGB1  
: VIDEO1  
: CMPNT1  
: CMPNT2  
: RGB  
AUDIO2  
AUDIO3  
BNC SELECT  
RGB SELECT  
HD SELECT  
RGB3 ADJUST  
1. From the main menu, highlight and select OPTIONS. The OPTIONS  
menu is displayed.  
: 1080A  
: 1  
2. Highlight the BNC SELECT option.  
ADJ.  
SEL.  
RETURN  
3. Use the button to toggle between RGB2 (composite) and CMPNT2.  
(component).  
This is the OPTIONS menu with the BNC  
SELECT option highlighted.  
4. Once youve selected the desired setting, press the button to return  
to the OPTIONS menu items or press CLEAR to return to the main  
menu.  
The factory defaults are as follows:  
RGB1 AUDIO1  
VIDEO INPUTS AUDIO 2  
COMPONENT INPUTS AUDIO3  
If you use the reset option, the settings will return to the factory default  
settings.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
SETTING A COMPUTER IMAGE TO THE CORRECT RGB  
SELECT MODE  
The RGB function allows you to select the correct viewing mode for the  
type of computer image you are displaying.  
OPTIONS  
AUDIO INPUT  
The RGB SELECT function has four modes:  
AUDIO1  
: RGB1  
: VIDEO1  
: CMPNT1  
: RGB2  
: VIDEO  
: 1080A  
: 1  
AUDIO2  
RGB Use this mode for normal computer images.  
AUDIO3  
VIDEO Use this mode to display video signal that has been converted to  
the RGB signal.  
BNC SELECT  
RGB SELECT  
HD SELECT  
RGB3 ADJUST  
WIDE Use this mode to prevent an image that is inputted from 852 dot X  
480 line signal with a vertical frequency of 31.72 KHz from being  
compressed horizontally.  
ADJ.  
RETURN  
SEL.  
DTV This mode is primarily used to optimize picture quality if you are  
using a generic-brand DTV receiver which output signal at 480P  
(progressive scan) lines.  
This is the OPTIONS menu with the RGB  
SELECT option highlighted.  
To change the RGB SELECT mode:  
1. From the main menu, highlight and select the OPTIONS menu. The  
OPTIONS menu is displayed.  
2. Highlight the RGB MODE option.  
3. Use the button to scroll through the mode choices. The settings  
switch as follows:  
4. When the desired mode is selected, press the button to return the  
the OPTIONS menu items. You can continue making adjustments  
within the OPTIONS menu, press GO BACK to return to the previous  
menu or press CLEAR to exit the menu system.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
SETTING THE CINEMA SCREEN MONITOR TO THE CORRECT  
HD RECEIVER MODE  
The HD SELECT function allows you to select the correct mode for the  
Cinema Screen monitor to work with your HD receiver. The default setting  
is 1080A. This is the correct setting for all RCA and PROSCAN HD  
receivers. If you have another brand of HD receiver, your picture may  
appear broken or off-center. If so, you need to switch HD SELECT modes.  
OPTIONS  
AUDIO INPUT  
AUDIO1  
: RGB1  
: VIDEO1  
: CMPNT1  
: RGB2  
: RGB  
AUDIO2  
AUDIO3  
1080A Use this option for RCA or PROSCAN HD receivers.  
1080B Use this option if you have any other brand of HD receiver.  
To change the receiver mode:  
BNC SELECT  
RGB SELECT  
HD SELECT  
RGB3 ADJUST  
: 1080A  
: 1  
1. From the main menu, highlight and select OPTIONS. The OPTIONS  
menu is displayed.  
ADJ.  
SEL.  
RETURN  
This is the OPTIONS menu with the HD  
SELECT option highlighted.  
2. Highlight the HD SELECT option.  
3. Use the button to select the desired mode (1080 A or 1080 B).  
4. When the desired number is selected, press the button to return the  
the OPTIONS menu items. You can continue making adjustments within  
the OPTIONS menu, press GO BACK to return to the previous menu or  
press MENU or CLEAR to exit the menu system.  
ADJUSTING THE DISPLAY IN RGB3 INPUT MODE  
OPTIONS  
If the picture is not stable in RGB3 mode, use the RG ADJUST feature to  
adjust it.  
AUDIO INPUT  
AUDIO1  
: RGB1  
: VIDEO1  
: CMPNT1  
: RGB2  
: RGB  
1. From the main menu, highlight and select OPTIONS. The OPTIONS  
menu is displayed.  
AUDIO2  
AUDIO3  
BNC SELECT  
RGB SELECT  
HD SELECT  
RGB3 ADJUST  
2. Highlight the RGB3 ADJUST option.  
3. Use the button to select the desired adjustment (1, 2 or 3). The  
choices scroll as follows:  
: 1080A  
: 2  
ADJ.  
SEL.  
RETURN  
This is the OPTIONS menu with the RBG3  
ADJ. option highlighted.  
4. When the desired number is selected, press the button to return the  
the OPTIONS menu items. You can continue making adjustments  
within the OPTIONS menu, press GO BACK to return to the previous  
menu or press MENU or CLEAR to exit the menu system.  
Note: When AUTO PICTURE is on, switch it off and back on again  
to return the display position to its original position.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
THE SETUP MENU  
The SETUP menu controls the way your monitor communicates.  
SETUP  
FREQUENCY  
MENU LANGUAGE  
COLOR SYSTEM  
CONFIRMING THE FREQUENCIES AND POLARITIES OF INPUT  
SIGNALS  
The FREQUENCY function is used to confirm the frequencies and polarities  
of the signals coming from a computer.  
To confirm frequencies and polarities:  
1. From the main menu, highlight and select the SETUP option. The  
SETUP menu is displayed.  
RETURN  
OK  
SEL.  
This is the SETUP menu with the  
FREQUENCY option highlighted.  
2. Highlight the FREQUENCY option and press OK.  
3. The FREQUENCY screen is displayed.  
Press GO BACK to return to the INFORMATION menu, or press  
CLEAR to exit the menu system.  
FREQUENCY  
H. FREQUENCY : 37.5KHz  
V. FREQUENCY : 75.0Hz  
SELECTING THE LANGUAGE FOR THE MENUS  
The menu display can be set to one of three lanuages: English, French or  
Spanish. The default is English. To change the default setting:  
H. POLARITY  
V. POLARITY  
: NEG.  
: NEG.  
1. From the main menu, highlight and select the SETUP option. The  
SETUP menu is displayed.  
2. Highlight the MENU LANGUAGE option. The MENU LANGUAGE  
screen is displayed.  
RETURN  
3. Use the button to scroll through the language choices. The settings  
switch as follows:  
This is the FREQUENCY screen.  
MENU LANGUAGE  
LANGUAGE  
: ESPANOL  
4. When the desired language is highlighted, press GO BACK to return  
to the SETUP menu. You can continue making adjustments within the  
SETUP menu, press GO BACK to return to the main menu, or press  
CLEAR to exit the menu system.  
˜
SETTING THEV IDEO SIGNAL FORMAT  
The COLOR SYSTEM option is used to set the video signal format.  
Different countries used different formats for video signals. The AUTO  
option automatically detects the correct video signal and sets the correct  
format. This setting should not be changed.  
ADJ.  
OK  
RETURN  
This is the MENU LANGUAGE screen with  
Spanish as the selected language.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
THE AUTOTUNING MENU  
AUTOTUNING THE COMPONENT BUTTONS ON THE  
REMOTE CONTROL  
The AUTOTUNING feature lets you easily program the component buttons  
on the remote to operate the components hooked up to the Cinema Screen  
monitor. To autotune your components to the buttons on the remote:  
AUTOTUNING SETUP  
HD RCVR BTN  
: RGB1  
SAT 2 BUTTON  
VCR1 BUTTON  
DVD BUTTON  
: NONE  
: VIDEO1  
: CMPNT1  
1. From the main menu, highlight and select the AUTOTUNING SETUP  
option. The AUTOTUNING SETUP menu is displayed.  
2. Highlight an option which corresponds to a component which youve  
connected. For example, if you have a DVD player connected,  
highlight the DVD BUTTON option.  
SEL.  
ADJ.  
RETURN  
This is the AUTOTUNE menu with the DVD  
BUTTON option highlighted.  
3. Use the button to scroll through the output choices. Select the  
choice which corresponds to the jacks you used to connect the DVD  
player. In the example illustration on the right, the DVD button on the  
remote will operate the component connected to the CMPNT1 jacks  
(the DVD player).  
4. When the desired option is displayed, press the button to return the  
the AUTOTUNING menu options. You can continue making  
adjustments within the OPTIONS menu, press GO BACK to return to  
the previous menu or press CLEAR to exit the menu system.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
The Menu System  
SLEEPTIMER  
The sleep timer is a feature that allows you to set the monitor to turn off  
after a prescribed amount of time. It can be set to turn the power off after  
30, 60, 90 or 120 minutes.  
SETTING THE SLEEP TIMER  
1. Press the SLEEP button on the remote to turn on the timer. The  
default is 30 minutes.  
2. Press the SLEEP button again to move to the next time increment.  
Press the SLEEP button until you get to the desired time.  
3. The timer starts when the Sleep display turns off.  
TO CHECK THE REMAINING TIME:  
1. Once the sleep timer has been set and the menu has turned off,  
press the SLEEP button once.  
2. The remaining time is displayed, then disappears after a few  
seconds.  
3. When five minutes remain, the remaining time appears until it  
reaches zero.  
CANCELLING THE SLEEP TIMER  
1. Press the SLEEP button twice in a row.  
2. The sleep timer is canceled.  
NOTE: After the power is turned off with the sleep timer, a slight  
current is still supplied to the monitor. If you do not plan to use  
the system for a long period of time, turn the power off with the  
remote or on the unit.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reference  
TECHNICAL INFORMATION  
setup and  
connections  
1
This section contains technical reference information  
about your Cinema Screen monitor, as well accessory  
and warranty information.  
The menu system  
2
3
reference  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reference  
INSTALLING THE CINEMA SCREEN MONITOR  
IMPORTANT  
• This device cannot stand on its own. Be sure to use a stand or original mounting unit.  
• For correct installation and mounting it is strongly recommended to use a trained, authorized Cinema Screen dealer.  
Failure to follow correct mounting procedures could result in damage to the equipment or injury to the installer.  
Product warranty does not cover damage caused by improper installation.  
ATTACHING OPTIONAL MOUNTS OR STAND TO THE CINEMA SCREEN MONITOR  
The Cinema Screen monitor can be mounted on the wall using an optional wall mount or you can attach a floor stand (also  
optional). For more information on mounting your Cinema Screen Display, see your Cinema Screen dealer.  
If you choose to use the optional wall mount, it can be attached to the Cinema Screen monitor in one of the following two  
ways:  
While it is upright.  
While it is laying with the screen face down. If you choose this option, lay the protective sheet that came wrapped  
around the monitor beneath the screen surface so it doesn’t get scratched.  
VENTILATION REQUIREMENTS FOR ENCLOSURE MOUNTING  
To allow heat to disperse, leave space between surrounding objects as shown on the diagram below when installing.  
WALL  
31mm (1.22”)  
31mm (1.22”)  
1110mm (43.7 ”)  
50mm (2”)  
WALL  
50mm (2”)  
VENTILATION SPACE AROUND UNIT  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reference  
CONNECTING YOUR PC OR MACINTOSH  
COMPUTER  
MINI D-SUB 15 PIN VGA SIGNAL  
COMPOSITION  
Connecting your PC or Macintosh computer to your  
Cinema Screen monitor will enable you to display  
computer images on the monitor. The Cinema Screen  
monitor supports the signals described on page 48.  
5
4
3
2
1
9
8
7
6
10  
15 14 13 12 11  
If you are connecting a computer to the monitor, you must  
attach the ferrite cores to both ends of the DVI cable to  
meet FCC standards (see page 6). To connect to a PC,  
Macintosh or compatible graphics adapter:  
Pin No.  
Signal to be connected  
RED  
1. Turn off the power to your monitor and computer.  
2. If your PC does not support XGA/SVGA/VGA you will  
need to install an XGA/SVGA/VGA graphics board.  
Consult your computer’s owner’s manual for your  
SXGA/XGA/ SVGA/VGA configuration. If you need to  
install a new board, see the manual that comes with  
your new graphics board for installation instructions.  
1
2
GREEN or sync. on Green  
BLUE  
3
4
No connection  
GND  
5
3. The Cinema Screen monitor provides signal  
compatibility with VESA 128021024@60MHz (SXGA).  
However, we recommend not using this resolution due  
to image readability on the monitor’s 853 X 480 native  
pixel resolution panel.  
6
RED (GND)  
GREEN (GND)  
BLUE (GND)  
No connection  
SYNC (GND)  
No connection  
SDA  
7
8
4. Use the signal cable that’s supplied to connect your PC  
or Macintosh computer to the Cinema Screen monitor.  
For Macintosh, you will need a monitor adapter (not  
supplied) to connect to your computer’s video port.  
9
10  
11  
12  
13  
14  
15  
5. Turn on the monitor and the computer.  
6. If the Cinema Screen monitor goes blank after a period  
of inactivity, it may be caused by a screen saver  
installed on the computer you’ve connected to the  
monitor.  
H. Sync  
V. sync  
SCL  
When using a Macintosh with the Cinema Screen  
monitor, the following three display standards are  
supported using the included Macintosh adapter : 13"  
fixed mode, 16" fixed mode, and 19" fixed mode. The  
13" fixed mode is recommended for the Cinema Screen  
monitor.  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reference  
SPECIFICATIONS  
Product Name  
1.18”  
41.3”  
2.32”  
PSP42300 Cinema Screen Monitor  
36.3"(H) X 20.4"(V) inches  
921(H) X 518.4(V) mm  
diagonal 42"  
Screen Size  
Aspect Ratio  
Resolution  
16 : 9  
853(H) X 480(V) pixels  
256 levels, 16,770,000 colors  
RGB, NTSC (3.584.43), PAL (B, G, M, N), PAL60,  
SECAM, HD*1, DVD*1, DTV*  
mini D-sub 15-pin  
Color Reproduction  
Input Signals  
RGB Input terminals  
Visual 1  
3.5”  
Visual 2  
BNC (R, G, B, H/CS, V) X1  
DVI-I 29-pin X 1*2  
Visual 3  
Video Input terminals  
Visual 1  
The features and specifications may be subject to change  
without notice.  
RCA-pin X 1  
Visual 2  
BNC X 1  
Visual 3  
S-Video: DIN 4-pin X 1  
* DTV input signals supported on this system  
DVD/HD/DTV  
Visual  
1080I (60 Hz)  
480P (60 Hz)  
480I (60 Hz)  
720P (60 Hz)  
RCA-pin (Y, PB[CB], PR[CR])  
Stereo RCA X 3  
Audio  
External Control  
Sound Output  
Power Supply  
Current Rating  
Power Consumption  
Dimensions (WxDxD)  
D-sub 9-pin X1 (RS-232C)  
7W+7W at 6 to 8 ohm  
AC120V 50/60Hz  
4.2A (maximum)  
395W (typical)  
1048 X 648 X 89mm (w/o stand)  
41.3 X 25.5 X 3.5 inches (w/o stand)  
1084 X 746 X 360mm (with stand)  
32 Kg/70.6 lbs. (w/o stand)  
0°C to 40°C/32°F to 104°F  
20 to 80%  
Net Weight  
Environmental Considerations  
Operating temperature  
Humidity  
0 to 1900m/0 to 6230 ft.  
Altitude  
-10°C to 50°C/14°F to 122°F  
10 to 90%  
Storage temperature  
Humidity  
0 to 3000m/0 to 9840 ft.  
Altitude  
Power on/off, Input source select,  
Volume up/down/OSM control  
Power Management, plug and play (DDCI,  
DDC2b, RGB3: DDC2b only)  
Remote control with two AA batteries, RGB  
cable (Mini D-sub 15 pin to Mini D-sub 15-pin  
connector), power cord, safety metal fitting,  
screw for safety metal fitting, User’s Manual  
UL approved (UL 1950, CSA 950)  
DOC Canada requirements  
Meets FCC class B requirements for home  
application  
Front Panel User Controls  
Other Features  
Accessories  
Regulations  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reference  
TROUBLESHOOTING  
Before requesting service, check the adjustments, operations, etc.  
Symptom  
Possible Problem  
Solutions  
• Is a connected component set directly in front  
or at the side of the monitor?  
Picture is disturbed.  
• Leave some space between the display and  
connected components.  
Sound is noisy.  
Remote control unit operates erroneously.  
• Remote control batteries may be dead.  
• Remote may be in wrong mode.  
The remote control does not work.  
• Replace both batteries with new ones.  
• Press component button for desired component.  
• Is the monitor’s power cord plugged into a  
power outlet?  
Monitor’s power does not turn on when the  
remote control’s power button is pressed.  
• Plug the monitor’s power cord into a power  
outlet.  
• Are all the monitor’s indicators off?  
• Press the power button on the monitor to turn  
on the power.  
• Is the remote control pointed at the monitor,  
or is there an obstacle between the remote  
control and the monitor?  
Monitor does not operate when the remote  
control’s buttons are pressed.  
• Point the remote control at the monitor’s  
remote control sensor when pressing buttons,  
or remove the obstacle.  
• Is direct sunlight or strong artificial light  
shining on the monitor’s remote control  
sensor?  
• Eliminate the light by closing curtains, pointing  
the light in a different direction, etc.  
• Remote control batteries may be dead.  
• Replace both batteries with new ones.  
• Is the monitor’s power cord plugged into a  
power outlet?  
No sound or picture is produced.  
• Plug the monitor’s power cord into a power  
outlet.  
• Is the source video connected and on?  
• Make sure source video (VCR, DVD, DTC) is  
connected and turned on.  
• Is the volume set at the minimum?  
• Is the mute mode set?  
Picture appears but no sound is produced.  
• Increase the volume.  
• Press the remote control’s mute button.  
• Connect the speakers properly.  
• Are the speakers properly connected?  
• Are the tint and colors properly adjusted?  
Tint is poor or colors are weak.  
Nothing appears on screen.  
• Adjust the tint and color (under PICTURE).  
• Return to factory reset.  
• Is the computer’s power turned on?  
• Is a video source connected?  
• Turn on the computer’s power.  
• Connect video source to the monitor.  
• Operate the computer (move the mouse, etc.).  
• Is the power manager function in the  
STANDBY or OFF mode?  
• Is the picture position adjusted correctly?  
Part of picture is cut off or picture is  
not centered.  
• Adjust the picture from the SCREEN menu.  
• Is the screen size adjusted correctly?  
Image is too large or too small.  
• Press the WIDE/AUTO WIDE button on the  
remote control and adjust properly.  
• Is the computer set at the correct resolution?  
• Is the HD receiver set to the correct mode?  
Picture is unstable.  
• Set to the proper resolution.  
• Set HD receiver to the correct mode (page 29).  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reference  
THE CINEMA SCREEN MONITOR MENU SYSTEM  
Main menu  
Sub menu  
CONTRAST  
BLACK LEVEL  
SHARPNESS  
COLOR  
Functions  
PICTURE QUALITY  
Adjusts the contrast.  
Adjusts the brightness.  
Adjusts the sharpness.  
Adjusts the color density (video input only).  
Adjusts the picture tint (video input only).  
Sets the picture mode according to the video environment.  
Adjusts the color temperature and white balance.  
Reduces noise visible in image.  
TINT  
PRESETS  
COLOR TEMP.  
NOISE REDUCE  
Sub menu  
BASS  
Main menu  
Functions  
AUDIO  
Sets the bass.  
TREBLE  
Sets the treble.  
BALANCE  
Sets the left/right balance.  
Main menu  
Sub menu  
V-POSITION  
H-POSITION  
V-HEIGHT  
Functions  
SCREEN  
Adjusts the vertical picture position of the picture on the screen.  
Adjusts the horizontal picture position of the picture on the screen.  
Adjusts the vertical size of the picure.  
Adjusts the horizontal size of the picure.  
When turned on, automatically adjusts for flickering and striped patterns.  
Adjusts for flickering in the picture.  
Adjusts for striped patterns in the picture.  
Functions  
H-WIDTH  
AUTO PICTURE  
FINE PICTURE  
PICTURE ADJ.  
Sub menu  
DISPLAY  
Main menu  
FUNCTION  
Turns the on-screen display on and off.  
Adjusts the vertical and horizontal position of the menu display.  
Sets the monitor for use as an energy-saving display when used with a computer.  
MENU ADJUST  
POWER SAVER  
GRAY LEVEL  
When viewing a picture with 4:3 aspect ratio, sets the luminance of both sides of  
the picture.  
PLE+INVERSE  
FILM MODE  
RESET  
Sets the brightness level to the minimum in VGA mode. Normally set to AUTO.  
When turned to AUTO, selects the correct viewing format.  
Resets ALL the settings to the factory default values.  
46  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reference  
Main menu  
Sub menu  
Functions  
OPTION  
AUDIO INPUT  
BNC SELECT  
RGB SELECT  
Allocates audio connectors.  
Sets BNC connectors to either composite or component video.  
Sets the appropriate mode for the computer image.  
RGB (VGA signals), VIDEO (Moving picture), WIDE (WIDE VGA) DTV.  
HD SELECT  
Sets correct mode for your HD digital receiver (1080 A or 1080 B).  
Adjusts the display position in RGB3 input.  
Functions  
RGB3 ADJUST  
Sub menu  
Main menu  
SETUP  
FREQUENCY  
Confirms the frequency and synchronizing polarities of the signal currently  
being inputted.  
MENU LANGUAGE Sets the language of the menus (English, French, or Spanish)  
COLOR SYSTEM  
Sub menu  
Sets the VIDEO format. Keep this set to AUTO.  
Main menu  
Functions  
AUTOTUNING SETUP  
HD RCVR BTN  
Autotunes the HD RCVR button on the remote control to the input that your  
HD receiver is hooked up to.  
SAT2 BUTTON  
VCR1 BUTTON  
DVD BUTTON  
Autotunes the SAT2 button on the remote control to the input that your  
satellite receiver is hooked up to.  
Autotunes the VCR button on the remote control to the input that your  
VCR is hooked up to.  
Autotunes the DVD button on the remote control to the input that your  
DVD player is hooked up to.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reference  
SUPPORTED RESOLUTION  
• When screen mode is NORMAL, each signal is converted to 640 dot X 480 line signal (except for *3).  
• When screen mode is FULL, each signal is converted to 853 dot X 480 line signal (except for *2).  
Notes:  
With Digital inputs some signals are not accepted.  
The sync may not be disturbed when non-standard signals other than the previously mentioned are input.  
When connecting a composite sync signal, use the HD terminal.  
Screen mode  
Vertical  
frequency (Hz)  
Vertical  
frequency (kHz)  
Model  
Dots X lines  
NORMAL  
FULL  
640 X 400  
640 X 480  
70.1  
59.9  
72.8  
75.0  
85.0  
100.0  
120.0  
60.0  
56.3  
60.3  
72.2  
75.0  
85.0  
100.0  
120.0  
60.0  
70.0  
75.0  
85.0  
100.0  
60.0  
66.6  
74.6  
74.9  
75.1  
31.5  
31.5  
37.9  
37.5  
43.3  
51.1  
61.3  
31.0  
35.2  
37.9  
48.1  
46.9  
53.7  
63.0  
75.7  
48.4  
56.5  
60.0  
80.5  
68.7  
64.0  
48.4  
56.5  
60.0  
68.7  
YES*1  
YES  
YES  
YES  
YES  
YES  
--  
YES*1  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
NO  
848 X 480*2  
800 X 600  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES*3  
YES  
YES  
YES  
YES  
*IBM PC/AT compatible computers  
1024 X 768  
NO  
1280 X 1024  
640 X 480  
832 X 624  
1024 X 768  
1152 X 870  
YES  
YES  
YES  
NO  
*Apple Macintosh  
NO  
*1 Displays only 400 lines with screen center of the vertical orientation located at the center.  
*2 Only when using a graphic accelerator board that is capable of displaying 848 X 480.  
*3 Aspect ratio is 5:4. This signal is converted to a 600 X 480 line signal.  
* IBM is a registered trademark of International Business Machines Corporation of the United States.  
* Macintosh is a registered trademark of Apple Computer, Inc. of the United States.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Reference  
RCA CINEMA SCREEN DISPLAY  
LIMITED WARRANTY  
WHAT YOUR WARRANTY COVERS:  
Any defect in materials or workmanship.  
FOR HOW LONG AFTER YOUR PURCHASE:  
One year for labor charges.  
One year for parts.  
The warranty period for rental units begins with the first rental or 45 days from date of shipment to the rental firm,  
whichever comes first.  
WHAT WE WILL DO:  
Exchange your unit with a new or, at our option, refurbished unit.  
HOW YOU GET YOUR UNIT REPAIRED:  
Call 1-800-433-8974 and have your units date of purchase and model/serial number ready.  
A representative will troubleshoot your problem over the phone.  
If the representative determines that you should receive service, they will provide you with the name(s) of the  
Authorized Cinema Screen Display Service Center in your area.  
Contact the Service Center and arrange for home service.  
Show the Authorized Service Center Representative your sales receipt or other evidence of purchase or first rental.  
The Authorized Service Center will repair your unit or make arrangements to deliver a new or refurbished unit and  
pick up your defective display all in one trip at no cost to you.  
WHAT YOUR WARRANTY DOES NOT COVER:  
Customer instruction. (Your Owners Manual clearly describes how to install, adjust, and operate your display. Any  
additional information should be obtained from your dealer.)  
Signal reception problems not caused by your Cinema Screen display.  
Damage from misuse or neglect.  
Batteries.  
A display purchased or serviced outside the U.S.A.  
Acts of Nature, such as but not limited to lightning damage.  
PRODUCT REGISTRATION:  
Please complete and mail the Product Registration Card packed with your unit. It will make it easier to contact you  
should it ever be necessary. The return of the card is not required for warranty coverage.  
HOW STATE LAW RELATES TO WARRANTY:  
This warranty gives you specific legal rights and you also may have other rights that vary from state to state.  
IF YOU PURCHASED YOUR DISPLAY UNIT OUTSIDE THE UNITED STATES:  
This warranty does not apply. Contact your dealer for warranty information.  
Service calls which do not involve defective materials or workmanship are not covered by this warranty. Costs of such  
service calls are the sole responsibility of the purchaser.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CINEMA SCREEN DISPLAY ACCESSORIES  
The Cinema Screen accessories listed below are available from your Cinema Screen Dealer. See your  
dealer for prices.  
CINEMA SCREEN ATTACHABLE SPEAKERS – SPK42  
CINEMA SCREEN DISPLAY STAND – PLB1  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
Symbols  
N
G
1080A 37  
1080B 37  
Navigating the menus 23  
Noise Reduction 27  
Number buttons 14  
Gain 26  
Go back button 13  
Gray level 33  
Guide button 13  
A
O
Antenna button 13  
Arrow buttons 13  
Audio input 35  
Audio menu 28, 46  
Automatic Code Search 16  
Auto picture 30  
H
OK button 14  
OnOff button 14  
On-screen Menus 23  
Display position 31  
Options menu 35, 47  
HD select 37  
HD RCVR button 14  
HD Receiver  
Connecting 9  
HD receiver 9  
HD Receiver Mode 37  
1080A 37  
Autotuning 39, 47  
Aux button 13  
P
Personal computer  
connecting 10, 11, 43  
Picture Quality menu 24, 46  
Picture mode  
B
1080B 37  
Balance 28  
Bass 28  
I
Batteries 9, 15  
Bias 26  
BNC select 35  
Black level 25  
Bright 24  
Memory 24  
Normal 24  
Preset 24  
Info button 13  
Input button 13  
Input Go Back 7  
Inserting batteries in the remote 15  
Installation 42  
Floor Stand 42  
Speakers 42  
Ventilation requirements 42  
Soft 24  
C
Picture position 30, 31  
PLE+INVERSE 33  
Power 22  
CH+/CH- button 13  
Cinema button 13  
Clear button 13  
CMPNT button 13  
Color system 38  
Components  
Connecting 11  
Computers  
Connecting 11, 43  
Contrast 25  
Power cord 6  
J
Power Saver 32  
Power/standby indicator 32  
Programming the remote 15  
Presets 24  
Jacks 8, 11  
AC IN 8  
External Speakers 8, 50  
External Control 8  
Video in/Audio in 8  
R
Reducing noise in the picture 27  
Remote Control  
L
Control Lock 8  
Automatic Code Search 16  
Buttons 13,14  
Codes 18  
inserting batteries 15  
Mute 22  
Navigating the Menus 23  
Programmable Codes 18  
Programming the Remote 16  
Resetting to default values 34  
RGB Select 36  
Language for the Menus 38  
Laser Disc Player 10  
D
Default values  
resetting 34, 46  
DTV 36  
DVD button 13  
DVD Player 10, 11  
M
Macintosh computer  
connecting 43  
Memory Mode 24  
Menu button 14  
Menu OK 7  
E
External control 8  
External Speakers 12, 50  
Menu display  
position 31  
S
Menu System 23, 46  
Mini D-sub 15 Pin VGA Signal Compo-  
sition 43  
Monitor button 14  
Mute 22  
F
Safety information 1, 2  
Safety metal fitting 6  
Screen menu 29, 46  
Ferrite cores 6  
Film mode 34  
Frequencies and Polarities of Input  
Signals 38  
Function menu 31, 46  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Index  
Specifications 44  
Stand  
using with Cinema Screen diaplay  
42, 50  
Screen size  
Fill 29  
Full 29  
Normal 29  
Video 36  
Viewing size  
selecting 29  
Volume 14, 22  
Vol+/- buttons 14, 22  
Stadium 29  
T
Setting the Color Temperature 26  
Setup menu 38, 47  
Sharpness 25  
Sleep button 14  
Sleep timer  
Cancelling 40  
Checking 40  
Setting 40  
W
TREBLE 28  
Troubleshooting 45  
Warranty 49  
Wide 36  
V
Z
VCR 10  
VCR1 button 14  
VCR2 button 14  
Ventilation Requirements 42  
Video button 14  
Zoom 7, 14  
Zoom in/Zoom out buttons 14  
Speakers 12, 50  
52  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Please do not send any products to the address listed in this manual or on the carton. This will only add delays in service for your product.  
10330 N. Meridian St.  
Indianapolis, IN 46290  
©2001 Thomson Consumer Electronics, Inc.  
Trademark(s) ® Registered  
Marca(s) Registrada(s)  
Printed in USA  
TOCOM 15730280  
Download from Www.Somanuals.com. All Manuals Search And Download.  

PYLE Audio Speaker PLMRBS10 User Guide
Radio Shack Universal Remote Wireless Remote Control System User Guide
RocketFish TV Mount RF TVMUC01 User Guide
Rose electronic Personal Computer MultiStation User Guide
Samsung Computer Drive HN M101MBB User Guide
Samsung Home Theater System HT E6500W User Guide
Schneider Electric Computer Hardware IP67 User Guide
Sears Dishwasher 6651359 User Guide
Sears Vacuum Cleaner 11317066 User Guide
Select Comfort Camping Equipment U 3000 User Guide