Radio Shack Universal Remote Wireless Remote Control System User Guide

61-2576.fm Page 1 Wednesday, September 8, 1999 1:50 PM  
Cat. No. 61-2576  
OWNER’S MANUAL  
Please read before using this equipment.  
Wireless Remote Control System  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 3 Wednesday, September 8, 1999 1:50 PM  
PLUG ‘N POWER PRECAUTIONS  
Turning lights and appliance on and off by remote control  
is a great convenience, but there can be some unexpect-  
ed consequences. For example, you might unknowingly  
turn on an empty coffee pot in another room, and it could  
be damaged by overheating or could even start a fire.  
You might also turn on an electric heater in another room  
when flammable materials are close to the heater. Again,  
damage or a fire could result.  
To prevent such problems, carefully plan what you want  
to control (as described in this manual) and keep a chart  
of your system handy. You must always be aware of what  
you are controlling.  
SAFETY PRECAUTIONS  
• Before using the product, please follow and adhere  
to all warnings, safety and operating instructions  
located on the product and in the owner's manual.  
Save all instructions for future use.  
• Do not attempt to control lights or appliances that  
exceed the ratings of the modules. If you want to  
control lights or appliances that exceed the ratings of  
the standard modules, see your local RadioShack  
store for information.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 4 Wednesday, September 8, 1999 1:50 PM  
• Use extreme care when controlling potentially dan-  
gerous products as part of your Plug ’N Power sys-  
tem. Use a separate unit code exclusively for such  
appliances.  
• If you want to control fluorescent, mercury vapor,  
sodium, or low voltage lights, see your local  
RadioShack store for assistance.  
• Do not use Lamp Dimmer Modules to control light fix-  
tures that have built-in dimmers.  
• Do not use Wall Switch or 3-Way Switch Modules to  
replace switches that control wall outlets or non-  
lighting devices.  
• The Wall Switch and Outlet Modules require direct  
connection to your house wiring. If you are not famil-  
iar with typical house wiring installation, we suggest  
that you have these types of modules professionally  
installed. In any case, be sure that the electricity is  
turned off at the circuit breaker or fuse panel while  
you are installing one of these modules.  
• Low-voltage electricity flows through the circuit con-  
trolled by a Wall Switch Module even when the switch  
is off. This is necessary for proper operation of the  
Wall Switch Module. You can completely turn off the  
electricity by sliding the switch's disable slide switch  
to off.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 5 Wednesday, September 8, 1999 1:50 PM  
CONTENTS  
Plug ‘N Power Precautions ..................................... 3  
Safety Precautions ................................................. 3  
How Plug ‘N Power Works ......................................... 6  
Setting Codes ......................................................... 6  
House Code ..................................................... 7  
Unit Code ......................................................... 8  
Placing the Control Center Module ........................ 9  
Preparation ................................................................ 10  
Installing Batteries ................................................ 10  
Setting the System ............................................... 11  
Setting up Additional Modules .............................. 13  
Setting the Module Codes .................................... 16  
Connecting Lights and Appliances to Modules .... 17  
Controlling Additional Modules ............................. 18  
Dimming or Brightening Lights Connected  
to Modules ............................................................ 20  
Local Control of Modules ...................................... 20  
Adding Another Center ......................................... 21  
Adding Other Controllers ...................................... 22  
Troubleshooting ........................................................ 24  
Care and Maintenance .............................................. 27  
Intercom Systems ................................................. 28  
Power Interruptions .............................................. 29  
FCC Statement ..................................................... 30  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 6 Wednesday, September 8, 1999 1:50 PM  
HOW PLUG ‘N POWER WORKS  
Plug ’N Power controllers such as your Wireless Remote  
Control System send high frequency signals through your  
household wiring. The remote control sends radio fre-  
quency signals to the control system’s receiver, which re-  
transmits the signals over your house wiring to other Plug  
’N Power modules.  
1
9
A
I
13  
5
M
E
1
1
1
5
3
1
5
3
1
3
5
1
3
5
1
1
7
1
1
7
9
9
UNIT  
UNIT  
A
A
O
C
O
C
M
E
M
E
K
G
K
G
I
I
HOUSE  
HOUSE  
APPLIANCE MODULE  
Be sure to carefully read this manual and the instructions  
that come with the modules. They are designed to help  
you get the most from your Plug ’N Power system.  
SETTING CODES  
Two different types of codes — house codes and unit  
codes — let you control many different modules or  
groups of modules within your home. It is important that  
you understand how these codes are used before you set  
up your system.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 7 Wednesday, September 8, 1999 1:50 PM  
House Code  
The house code is a master code for a  
Plug ’N Power system. You must set the  
remote control center mode and all the  
modules it controls to the same house  
code. There are 16 codes to choose from  
(A through P).  
A
I
O
C
G
M
E
K
You can operate two or more independent Plug ’N Power  
systems in your home by using a different house code for  
each system. Of course, each system must have its own  
controller and modules.  
You can control the same modules from two or more con-  
trollers by setting all the modules and controllers to the  
same house code.  
The different house codes also help to prevent interfer-  
ence between your Plug ’N Power system and other re-  
mote control systems in your neighborhood.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 8 Wednesday, September 8, 1999 1:50 PM  
Unit Code  
Each Wireless Remote Control Center  
can operate up to 16 different modules or  
groups of modules. Every module has a  
unit code dial with settings from 1 through  
16. You can set the control center to con-  
trol any module or group of modules set  
to the same house code.  
1
9
15  
13  
11  
3
7
5
The unit code dial on the control center sets the code for  
the outlet on the control center. It can be set to respond  
to unit codes 1 through 16. However, the remote control  
can be set to control modules 1–8 or 9–16 by setting its  
slide switch accordingly. The control center will respond  
to all 16 unit codes and retransmit them to the Plug ’N  
Power modules.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 9 Wednesday, September 8, 1999 1:50 PM  
PLACING THE CONTROL CENTER  
MODULE  
Because the control center’s module is a receiver and  
also a transmitter, you need to consider the best location  
for its installation.  
If you only want to use the control center module to con-  
trol something plugged into it, then connect it to an outlet  
near the lamp or appliance you want to control. However,  
if you want to control other Plug ’N Power modules  
through the control center receiver, consider a location  
where it can receive the signals from the remote control  
more easily.  
Some houses have aluminum-clad insulation that might  
act as a barrier to radio signals, depending on where the  
control center module is located. You might find that you  
can activate the control center receiver from a greater  
distance if you place it in your garage, which is usually  
not as insulated as the rest of the house.  
If your house is large, you can increase the transmitting  
range by adding multiple Wireless Remote Control Sys-  
tems.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 10 Wednesday, September 8, 1999 1:50 PM  
PREPARATION  
INSTALLING BATTERIES  
Your remote control requires four AAA batteries (not sup-  
plied) for power. For the best performance and longest  
life, we recommend RadioShack alkaline batteries.  
Cautions:  
• Use only fresh batteries of the required size and rec-  
ommended type.  
• Do not mix old and new batteries, different types of  
batteries (standard, alkaline, or rechargeable), or  
rechargeable batteries of different capacities.  
Follow these steps to install batteries.  
1. Use your fingernail or another object to lift up the bat-  
tery compartment cover to remove it.  
2. Place the batteries in the compartment as indicated  
by the polarity symbols (+ and ) marked inside.  
3. Replace the cover.  
When the remote control stops operating properly, re-  
place the batteries.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 11 Wednesday, September 8, 1999 1:50 PM  
Warning: Dispose of old batteries promptly and properly.  
Do not burn or bury them.  
Caution: If you do not plan to use the remote control for  
a month or more, remove the batteries. Batteries can  
leak chemicals that can destroy electronic parts.  
SETTING THE SYSTEM  
1. Use a small screwdriver to set the house code dials  
on both the remote control and the control center  
receiver to the same letter. If you already own other  
Plug ’N Power accessories and are adding the Wire-  
less Remote Control Center to your system, set both  
house codes to the same letter as the rest of your  
system.  
2. Set 18/916 on the remote control to the desired  
setting. For example, if you want to control mod-  
ules 1–8, set 18/916 to 18.  
3. Plug the light or appliance to be controlled into the  
AC outlet on the bottom of the control center’s  
receiver, then plug the receiver into a standard AC  
outlet.  
4. Be sure the light or appliance is turned on.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 12 Wednesday, September 8, 1999 1:50 PM  
5. Press ON/OFF on the receiver to make sure the light  
or appliance turns on and off.  
6. If 18/916 on the remote control is set to 916,  
press the button under ON or OFF next to 1 and 9  
(labeled on your remote) to turn the light or appliance  
on or off.  
7. Use your fingernail or another object to remove the  
clear cover over the label on the remote, and write  
down the location of each Plug ’N Power module you  
are using with the system on the label. Then press  
the clear cover back onto the remote.  
8. Press the button under ON next to 1 and 9 on the  
remote control to turn on the light or appliance  
plugged into the control center module. Or, press the  
button under OFF next to 1 and 9 on the remote con-  
trol to turn off the light or appliance.  
So far, we have described how to control just one light or  
appliance that is plugged into the Wireless Remote Con-  
trol Center. However, you can control up to 16 lights and  
appliances by using additional lamp modules, appliance  
modules, and wall switch modules.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 13 Wednesday, September 8, 1999 1:50 PM  
SETTING UP ADDITIONAL MODULES  
The following are types of Plug ’N Power modules avail-  
able from RadioShack. We include a brief description  
here, but be sure to read and follow the instructions that  
come with each module. Other types of modules are also  
available. If you have special Plug ’N Power needs, ask  
for assistance at your local RadioShack store.  
Appliance Modules (Cat. No.  
61-2681B) — These modules  
have a two prong plug and are  
designed to control small appli-  
ances, rated up to 15 amps resis-  
tive (such as coffee pots). You  
can also use them to control mo-  
1
3
tors up to  
/
horsepower and  
lamps that do not exceed 500  
watts.  
Universal Appliance Modules (Cat. No. 61-2684B) —  
These modules have the same features as the Appliance  
Module, but also provide connections for appliances that  
have 3-prong grounded plugs. You must plug these mod-  
ules into 3-prong grounded AC outlets.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 14 Wednesday, September 8, 1999 1:50 PM  
Lamp Dimmer Modules (Cat. No. 61-2682) — These  
modules are designed to control lamps, and you can dim  
the connected lamps from a Plug ’N Power controller.  
You can connect incandescent lamps of up to 300 watts  
to these modules.  
Lamp Dimmer Modules respond to the ALL LIGHTS ON  
command. Use the module only for incandescent lamps.  
Some devices might be damaged by the use of the dim-  
mer circuit (even if you don't dim the module). Do not use  
this module with lights that have built-in dimmers.  
Wall Switch Modules (Cat. No. 61-  
2683C) — These modules replace  
an existing wall switch. You can  
control incandescent lighting of up  
to 500 watts with one of these mod-  
ules, and you can also manually  
control the lights. Wall Switch Mod-  
ules also respond to the ALL  
LIGHTS ON command.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 15 Wednesday, September 8, 1999 1:50 PM  
Caution: Do not use Lamp Dimmer modules, Wall  
Switch Modules, or 3-Way Wall Switch Modules with fluo-  
rescent lighting.  
3-Way Wall Switch Modules  
(RSU 11911039) — These  
modules are similar to Wall  
Switch Modules, except that  
they are designed to control a  
light that is presently con-  
trolled from two different wall  
switches. 3-Way Wall Switch  
Modules come with a com-  
panion switch to replace the  
second existing switch.  
3-Way Wall Switch Modules respond to the ALL LIGHTS  
ON command and can control incandescent lighting of up  
to 500 watts. You also have manual control from both  
wall switches.  
Low-voltage electricity flows through the circuit controlled  
by a Wall Switch Module even when the switch is off.  
This is necessary for proper operation of the Wall Switch  
Module. You can completely turn off the electricity by set-  
ting the Wall Switch Module's disable switch to off (to the  
left).  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 16 Wednesday, September 8, 1999 1:50 PM  
Wall Outlet Modules (Cat. No. 61-  
2685) — These modules completely  
replace existing wall outlets, but you  
can only control the top outlet from a  
Plug ’N Power controller. The bottom  
outlet is always on.  
You can connect appliances or lamps  
that draw a total of up to 1800 watts to  
the outlet module. Because you might  
use the outlet module to control an appliance, these mod-  
ules do not respond to the ALL LIGHTS ON command.  
Caution: Do not use a Wall Outlet Module to replace an  
outlet that is controlled by a wall switch. You will lose  
control of the module if the wall switch is inadvertently  
turned off.  
SETTING THE MODULE CODES  
Set the house code dials on all the modules you want the  
Wireless Remote Control System to control to the same  
letter as you set on the control center receiver and re-  
mote control (A through P).  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 17 Wednesday, September 8, 1999 1:50 PM  
Set the selector switch dial on the remote control to 1–8 if  
you want to control the lamp and appliance set from 1 to  
8, or control from 9 to 16 if you set the selector switches  
to 9–16.  
CONNECTING LIGHTS AND  
APPLIANCES TO MODULES  
After setting the desired house codes and selector  
switch, place the supplied labels in the boxes next to the  
buttons on the remote control to remind you of what each  
button controls.  
Set the power switch on the light or appliance to the ON  
position. Then plug the light or appliance into the receiver  
and plug the receiver into an outlet.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 18 Wednesday, September 8, 1999 1:50 PM  
Follow the procedure in “Controlling Additional Modules”  
to test each receiver module. See “Intercom Systems” on  
Page 28 if your system does not work properly.  
CONTROLLING ADDITIONAL  
MODULES  
1. Set the remote control's slide switch to the group of 8  
modules you want to control (1–8 or 9–16). For exam-  
ple, if you set the switch to 1–8, the buttons on the  
remote control will control modules set to 1 through  
8.  
Notes:  
• Button 1 can also turn the receiver module on or  
off.  
• One side of the supplied label has numbers for  
modules 1 through 8 printed on it, and the other  
side has numbers for modules 9 through 16. Use  
the side of the label that matches your installation.  
2. Install additional Plug ’N Power modules (sold sepa-  
rately) as desired, following the instructions included  
with them.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 19 Wednesday, September 8, 1999 1:50 PM  
Caution: Be sure to turn off the power at the main  
circuit breaker panel before installing Wall Switch  
Modules or Wall Outlet Modules.  
3. Set the house code dial on all your Plug ’N Power  
modules to the same letter as you set on the remote  
control module.  
4. Set the unit code dial on your Plug ’N Power modules  
to a number between 1 and 8 (or 9 and 16 if you set  
the selector switches on the Remote Control to 9-16).  
5. To turn the Plug ’N Power modules on or off, press  
the corresponding button on the remote control for  
modules set to that unit code.  
The first button on the remote control always controls the  
control center receiver, and all 16 buttons will control oth-  
er Plug ’N Power modules set to codes 1 through 16.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 20 Wednesday, September 8, 1999 1:50 PM  
DIMMING OR BRIGHTENING LIGHTS  
CONNECTED TO MODULES  
Turn on the module by pressing the button on the remote  
control that corresponds to the module's unit code. Then  
press  
or  
on the remote control to dim or bright-  
en the light. Hold the button down until you see the de-  
sired brightness level.  
Note: Because the control center only turns a lamp/appli-  
ance on or off, you cannot use the control center receiver  
to dim/brighten a lamp/appliance connected to it.  
LOCAL CONTROL OF MODULES  
Even through your lights and appliances are connected  
to Plug ’N Power modules, you can still turn most of them  
on locally using their power switches.  
• For most products, simply turn the power switch off  
and back on again.  
• For three-way lamps, you might have to turn the  
lamp's switch several times before the light turns on.  
• You cannot manually turn on instant-on TVs or  
remote controlled TVs that are connected to Plug ’N  
Power modules.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 21 Wednesday, September 8, 1999 1:50 PM  
• You always have manual control of Wall Switch Mod-  
ules by simply using their on/off buttons.  
1
9
A
I
13  
5
M
E
ON  
OFF  
ADDING ANOTHER CENTER  
You can also add additional remote controls (available at  
your local RadioShack store) to your system. For exam-  
ple, you could place a remote control in each room or  
even in your car, so you can easily turn on/off modules  
set to unit codes 116 from any location.  
You can also control the control center receiver and other  
system modules from another type of Plug ’N Power con-  
troller (see “Adding Other Controllers” on Page 22). By  
adding a Timer/Controller or Clock Radio/Timer to the  
system, you can program modules to turn on or off auto-  
matically at set times.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 22 Wednesday, September 8, 1999 1:50 PM  
ADDING OTHER CONTROLLERS  
You can easily increase the size and flexibility of your  
Plug ’N Power system by adding more modules or other  
Plug ’N Power controllers.  
Mini Remote Control Center (Cat. No. 61-2677C ) —  
D
lets you instantly control up to eight Plug ’N Power mod-  
ules and dim lights, too. This controller also has ALL  
LIGHTS ON and ALL UNITS OFF controls.  
Keychain-Remote Light/Appliance Switch (Cat. No.  
61-2663  
) — lets you individually turn lights or appli-  
A
ances on or off from any location in your home.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 23 Wednesday, September 8, 1999 1:50 PM  
Wireless Home Security System (Cat. No. 49-2551A)  
— lets you work with a total of 16 wireless sensor trans-  
mitters, lamp modules, motion detectors, and other ac-  
cessories to customize your home security system.  
Programmable Control Center & Timer (Cat. No. 61-  
2470) — lets you control up to eight groups of lights or  
appliances anywhere in your house using Plug ’N Power  
modules, plus a timer you can use to pre-program events  
to take place while you are away.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 24 Wednesday, September 8, 1999 1:50 PM  
TROUBLESHOOTING  
If your system is not working as it should, try these sug-  
gestions.  
Symptom  
Suggestion  
The remote control  
does not turn the con-  
trol center receiver on  
or off.  
Make sure the red light on the  
remote control lights when you  
press a button.  
The batteries in the remote con-  
trol might be weak. Replace the  
batteries.  
Make sure the house code dials  
on the remote control and control  
center module are set correctly.  
Make sure that 1-8/9-16 on the  
remote control is set correctly.  
Make sure that you have power to  
the AC outlet and the light or  
appliance is turned on.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 25 Wednesday, September 8, 1999 1:50 PM  
Symptom  
Suggestion  
The control center  
module does not turn  
on or off using another  
type of Plug ’N Power  
controller.  
Try plugging the control center  
receiver and the other Plug ’N  
Power controller into the same AC  
outlet. If it does not work in any  
AC outlet even when connected  
to the same duplex (top and bot-  
tom) of the AC outlet, replace the  
control center receiver. If it works  
in some AC outlets but not in oth-  
ers, contact your local  
RadioShack store for help.  
You cannot control  
other Plug ’N Power  
modules from your  
remote control.  
Make sure the red light on the  
remote control lights when you  
press a button.  
The batteries in the remote con-  
trol might be weak. Replace the  
batteries.  
Make sure the house code dials  
on the remote control and control  
center module are set correctly.  
Make sure that 1-8/9-16 on the  
remote control is set correctly.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 26 Wednesday, September 8, 1999 1:50 PM  
Symptom  
Suggestion  
You cannot control  
other Plug ’N Power  
modules from your  
remote control  
Make sure that you have power to  
the AC outlet and the light or  
appliance is on.  
Plug another Plug ’N Power con-  
troller and the modules into the  
same AC outlet, then try to control  
the modules again. If your control-  
ler is the only one you have, use  
an extension cord to plug the con-  
trol center receiver and your other  
Plug ’N Power module into the  
same AC outlet. If the module still  
does not work, replace the mod-  
ule.  
(continued).  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 27 Wednesday, September 8, 1999 1:50 PM  
CARE AND MAINTENANCE  
Your RadioShack Plug ’N Power Wireless Remote Con-  
trol System is an example of superior design and crafts-  
manship. The following suggestions will help you care  
for your system so it will serve you for years.  
Keep the system dry. If it gets wet, wipe it  
dry immediately. Liquids might contain min-  
erals that can corrode the electronic circuits.  
Use and store the system only in normal  
temperature environments. Temperature ex-  
tremes can shorten the life of electronic de-  
vices, damage batteries, and distort or melt  
plastic parts.  
Keep the system away from dust and dirt,  
which can cause premature wear of parts.  
Handle the system gently and carefully.  
Dropping it can damage circuit boards and  
cases and can cause the system to work im-  
properly.  
Use only fresh batteries of the required size  
and recommended type. Batteries can leak  
chemicals that damage your system’s elec-  
tronic parts.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 28 Wednesday, September 8, 1999 1:50 PM  
Wipe the system with a damp cloth occa-  
sionally to keep it looking new. Do not use  
harsh chemicals, cleaning solvents, or  
strong detergents to clean the system.  
Modifying or tampering with the system’s internal com-  
ponents can cause a malfunction and might invalidate  
its warranty and void your FCC authorization to operate  
it. If your system is not performing as it should, take it to  
your local RadioShack store for assistance.  
INTERCOM SYSTEMS  
Intercom systems which send voice signals over existing  
electrical wiring may interfere with the ability to control  
other modules from your control center when the inter-  
com is in use. If the intercom system has its own sepa-  
rate wiring, it will not cause a problem. Intercoms will not  
interfere with the ability to control the control center from  
the remote control.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 29 Wednesday, September 8, 1999 1:50 PM  
POWER INTERRUPTIONS  
When the power is restored after an outage, Lamp Mod-  
ules and Wall Switch Modules will normally be OFF. You  
can use the remote control to turn Lamp and Wall Switch  
modules on after a power failure. Appliance modules (in-  
cluding the control center receiver) have a latching relay  
mechanism and will stay as they were before the inter-  
ruption.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 30 Wednesday, September 8, 1999 1:50 PM  
FCC STATEMENT  
This equipment generates and uses radio frequency en-  
ergy, and if not installed and used properly, that is, in  
strict accordance with the manufacturer's instructions,  
may cause interference to radio and television reception.  
It has been type tested and found to comply with the lim-  
its for remote control security devices in accordance with  
the specifications in sub-parts C and E of Part 15 of FCC  
Rules. These limits provide reasonable protection against  
radio and TV interference in a residential area. However,  
your equipment might cause TV or radio interference  
even when it is operating properly. To eliminate interfer-  
ence, you can try one or more of the following corrective  
measures:  
• reorient or relocate the receiving antenna  
• increase the distance between the equipment and  
the radio or TV  
• use outlets on different electrical circuits for the  
equipment and the radio or TV  
Consult your local RadioShack store if the problem still  
exists.  
You must use shielded interface cables with this equip-  
ment.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 31 Wednesday, September 8, 1999 1:50 PM  
NOTES  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
61-2576.fm Page 32 Wednesday, September 8, 1999 1:50 PM  
Limited Ninety-Day Warranty  
This product is warranted by RadioShack against manufacturing defects in  
material and workmanship under normal use for ninety (90) days from the date  
of purchase from RadioShack company-owned stores and authorized Ra-  
dioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, Ra-  
dioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED  
WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FIT-  
NESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO  
THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED  
HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO  
LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PER-  
SON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE  
CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF  
THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY,  
INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM  
INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR  
PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUEN-  
TIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POS-  
SIBILITY OF SUCH DAMAGES.  
Some states do not allow the limitations on how long an implied warranty lasts  
or the exclusion of incidental or consequential damages, so the above limita-  
tions or exclusions may not apply to you.  
In the event of a product defect during the warranty period, take the product  
and the RadioShack sales receipt as proof of purchase date to any Ra-  
dioShack store. RadioShack will, at its option, unless otherwise provided by  
law: (a) correct the defect by product repair without charge for parts and labor;  
(b) replace the product with one of the same or similar design; or (c) refund the  
purchase price. All replaced parts and products, and products on which a re-  
fund is made, become the property of RadioShack. New or reconditioned parts  
and products may be used in the performance of warranty service. Repaired  
or replaced parts and products are warranted for the remainder of the original  
warranty period. You will be charged for repair or replacement of the product  
made after the expiration of the warranty period.  
This warranty does not cover: (a) damage or failure caused by or attributable  
to acts of God, abuse, accident, misuse, improper or abnormal usage, failure  
to follow instructions, improper installation or maintenance, alteration, lightning  
or other incidence of excess voltage or current; (b) any repairs other than  
those provided by a RadioShack Authorized Service Facility; (c) consumables  
such as fuses or batteries; (d) cosmetic damage; (e) transportation, shipping  
or insurance costs; or (f) costs of product removal, installation, set-up service  
adjustment or reinstallation.  
This warranty gives you specific legal rights, and you may also have other  
rights which vary from state to state.  
RadioShack Customer Relations, 200 Taylor Street, 6th Floor,  
Fort Worth, TX 76102  
04/99  
We Service What We Sell  
09A99  
Printed in China  
Download from Www.Somanuals.com. All Manuals Search And Download.  

PYLE Audio Stereo Amplifier PTA3 User Guide
Renesas Computer Hardware REG10J0083 0100 User Guide
Revolabs Home Security System 01 HDEXEC NM User Guide
RocketFish Headphones RF WHD200 User Guide
Rockford Fosgate Stereo Amplifier 4 CHANNEL AMPLIFIER User Guide
Rosewill Computer Drive RX81US HT 25A BLK User Guide
Samsung Clothes Dryer DV50F9A8GVP User Guide
Samsung Microwave Oven CE282DNT User Guide
Samsung Projector Accessories S19A350B User Guide
Sears Treadmill 831297940 User Guide