’ :
-
PHD50300
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Information
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates “dangerous
voltage” inside the product that
presents a risk of electric shock
or personal injury.
This symbol indicates
important instructions
accompanying the product.
Precautions
FCC Information
Please read this manual carefully before using your Monitor and
keep the manual handy for future reference.
•
FCC Regulations state that unauthorized changes or
modifications to this equipment may void the user's authority
to operate it.
WARNING
•
This equipment has been type tested and found to comply
with the limits for a Class B Digital Device in accordance
with the specifications in Part 15 of the FCC rules. These
rules are designed to provide reasonable protection against
radio and television interference in a residential installation.
This equipment generates and can radiate radio ferquency
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO DO
NOT USE THIS UNIT’S PLUG WITH AN EXTENSION
CORD RECEPTACLE OR OTHER OUTLETS, UNLESS ALL
PRONGS CAN BE FULLY INSERTED. REFRAIN FROM
OPENING THE CABINET AS THERE ARE HIGH-VOLTAGE
COMPONENTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Industry Canada Compliance Notice
This Class B digital apparatus meets all erquirements of the
Canadian Interference-Causing Equipment Regulations.
If this equipment does cause interference to the radio or
television reception (which you can determine by turning the
equipment off and on), try to correct the interference by one
or more of the following measures:
Declaration of Conformity
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
•
Reorient or relocate the receiving antenna (that is,
the antenna for the radio or television that is
"receiving" the interference).
•
Change the position of the monitor with erspect to
the radio or television equipment that is erceiving
the interference.
Product: Cinema Screen Display
Equipment Classification: Class B Computer Peripheral
Model: PHD50300
•
•
Move the monitor away from the equipment
receiving the interference.
We hereby declare that the equipment specified above confomr s to
the technical standards as specified in the FCC rules.
Plug the monitor into a diferent wall outlet so the
receiver and the equipment are on different branch
circuits.
Thomson multimedia Inc.
10330 N. Meridian St.
Indianapolis, IN 46290
Phone: 1-800-433-8974
If these measures do not eliminate interference, please
consult your dealer or an experienced radio/television
technician for additional suggestions. Also, the Federal
Communications Commission has prepared a helpful
booklet, "How to Identify and Resolve Radio/TV Intefrerence
Problems." This booklet is available from the U.S.
Cable TV Installer: This reminder is provided to call your
attention to Article 820-40 of the National Electrical Code (Section
54 of the Canadian Electrical Code, Part 1) which porvides
guidelines for proper grounding and, in particular, specifies that
the cable ground shall be connected to the gor unding system of
the building as close to the point of cable entry as practical.
Government Printing Office, Washington D.C., 20402. Please
specify stock number 004-000-00345-4 when ordering copies.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warnings and Safety Precautions
IMPORTANT TIPS: Caring for Your
Monitor
The monitor is designed and manufactured to provide
long, trouble-free service. No maintenance other than
cleaning is required. Use a soft dry cloth to clean the
panel. Never use solvents such as alcohol or thinner to
clean the panel surface.
To avoid damage and prolong operating life:
1. Use only with 120V 50/60Hz AC power supply.
Continued operation at line voltages greater than 120
Volts AC will shorten the life of the unit, and might
cause a fire hazard.
The display panel consists of fine pictuer elements (cells).
Although the display panels are produced with more than
99.99 percent active cells, there may be some cells that do
not produce light or remain lit.
2. Handle the unit carefully when installing it.
3. Locate set away from heat, excessive dust, and direct
sunlight.
For operating safety and to avoid damage to the unit,erad
carefully and observe the following instructions.
4. Protect the inside of the unit for m liquids and small
metal objects. In case of accident, unplug the unit and
have it serviced by an authorized service cente.r
To avoid shock and fire hazards:
1. Provide adequate space for ventilation to avoid
internal heat build-up. Do not cover erar vents or
install in a closed cabinet or shelves.
5. Do not hit or scratch the panel sufrace as this causes
flaws on the surface of the screen.
The unit is equipped with cooling fans. If you install
the unit in an enclosure, be sure there is adequate
space at the top of the unit to allow hot air to rise and
escape.
6. For correct installation and mounting it is storngly
recommended to use a trained, authorized deale.r
7. Like all phosphor-based display devices, monitors can
be susceptible to uneven phosphor aging under certain
circumstances. Certain operating conditions, such as
the continuous display of a static image over a
If the monitor becomes too hot, the ovehreat protector
will be activated and the monitor will be tunred off. If
this happens, turn off the power to the monitor and
un-plug the power cord. If the room where the
monitor is installed is particularly hot, move the
monitor to a cooler location, and wait for the monitor
to cool for 60 minutes.
prolonged period of time, can result in uneven
phosphor aging if proper precautions are not taken. To
protect your investment in this monito,r please adhere
to the following guidelines and recommendations for
minimizing the occurrence of uneven phosphor aging:
If the problem persists, contact your dealer for service.
•
Always enable and use your computer’s sceren saver
function during use with a computer input soucre.
2. Do not use the power cord plug with extension cords
or outlets unless all prongs can be completely inserted.
•
•
Display a moving image whenever possible.
3. Do not expose unit to water or moistuer.
Always power down the monitor when you aer
finished using it.
4. Avoid damage to the power cord, and do not attempt
to modify the power cord.
•
If viewing with a 4/3 aspect ratio for long periods of
time, set side gray level at 3 or 4.
5. Unplug unit during electrical storms or if unit will not
be used over a long period.
6. Do not open the unit which has potentially dangeorus
high voltage components inside. If the unit is damaged
from opening the cabinet the warranty will be void.
Moreover, there is a serious risk of electric shock.
If the monitor is in long term use or
continuous operation take the following
measures to reduce the likelihood of uneven
phosphor aging:
7. Do not attempt to service or erpair the unit. Tmm is
not liable for any bodily harm or damage caused if
unqualified persons attempt service or open the back
cover. Refer all service to authorized Service Centers.
•
Lower the BRIGHTNESS and CONTRAST levels as
much as possible without impairing image eradability.
•
Display an image with many colors and color
gradations (i.e. photographic or photo-realistic
images).
•
•
Create image content with minimal contrast between
light and dark areas (for example, white characters on
black backgrounds). Use complementary or pastel
color whenever possible.
Avoid displaying images with few colors and distinct,
sharply defined borders between colors.
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Safety Information ................................................................................... 1
Warnings and Safety Precautions ...................................................................................2
IMPORTANT TIPS: Caring for Your Monitor ...................................................................2
Getting Started ......................................................................................... 5
Contents of the Package ..................................................................................................6
Part Names and Functions – Front View .........................................................................7
Part Names and Functions – Back View ..........................................................................8
Battery Installation...........................................................................................................9
Connecting an HD Receiver .............................................................................................9
The Back of the HD Receiver .....................................................................................9
Connecting Your VCR Or Laserdisc Player.....................................................................10
Connecting Your DVD Player .........................................................................................10
Connecting a Personal Computer ..................................................................................10
Connecting Components to the Monitor......................................................................11
Connecting External Speakers to the Monitor.............................................................12
A Quick Tour of the Remote Control .............................................................................13
Using Your Remote Control .....................................................................................15
Inserting Batteries..............................................................................................15
Programming the Remote .......................................................................................15
Find Out If You Need to Program the Remote ................................................15
How to Program the Remote ............................................................................16
Using Automatic Code Search...........................................................................16
Using Direct Entry ..............................................................................................17
How To Use the Remote Control
After You’ve Programmed It ...................................................................................17
Programmable Codes for the Remote Control.......................................................18
The Menu System ................................................................................... 21
Basic Operations .............................................................................................................22
Power ........................................................................................................................22
Volume ......................................................................................................................22
Mute..........................................................................................................................22
Navigating the Menus .............................................................................................22
The Multi-Screen Feature ........................................................................................23
Selecting the Input Signals to be displayed .....................................................24
On-Screen Menu Operation ....................................................................................24
The PICTURE QUALITY Menu .........................................................................................25
Setting the Picture Mode.........................................................................................25
Adjusting the Picture Settings in MEMORY Mode.................................................26
Setting the Color Temperature................................................................................27
Reducing Noise in the Picture .................................................................................28
The AUDIO Menu............................................................................................................29
The SCREEN Menu ..........................................................................................................30
Selecting a Viewing Size ..........................................................................................30
Adjusting the Picture Position and Size ..................................................................31
Auto Picture..............................................................................................................31
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
The FUNCTION Menu......................................................................................................32
On-Screen Displays ...................................................................................................32
Adjusting the Position of the Menu Display ..........................................................32
Setting the POWER SAVER for Computer Images ..................................................33
The POWER/STANDBY Indicator ..............................................................................33
Setting the Gray Level for the Sides of the Screen ................................................34
Adjusting for Flickering with Film Mode ................................................................34
Adjusting the Display in RGB3 Input Mode ............................................................35
Setting the Screen Saver ..........................................................................................35
Setting the PLE ...................................................................................................35
Turning Orbiter On ............................................................................................36
Setting the Inverse .............................................................................................36
Resetting to Default Values .....................................................................................37
The OPTIONS Menu ........................................................................................................38
Setting the Audio Inputs .........................................................................................38
Setting the BNC Connectors ....................................................................................38
Setting a Computer Image to the Correct RGB
Select Mode .....................................................................................................39
Setting the Monitor to the correct
HD Receiver Mode...........................................................................................40
Setting the Picture Size for RGB input signals........................................................40
The SETUP Menu.............................................................................................................41
Confirming the Frequencies, Polarities, mode
and resolution of Input Signals.........................................................................41
Selecting the Language for the Menus ..................................................................42
Setting the Video Signal Format .............................................................................42
The AUTOTUNING SETUP Menu ....................................................................................43
Autotuning the Component Buttons on he Remote Control................................43
SLEEP TIMER....................................................................................................................44
Setting the Sleep Timer............................................................................................44
Cancelling the Sleep Timer................................................................................44
Other Information .................................................................................. 45
Installing the Monitor ....................................................................................................46
Attaching optional mounts or stand to the Cinema
Screen monitor ......................................................................................................46
Connecting Your PC Or Macintosh Computer ..............................................................47
Mini D-sub 15 Pin VGA Signal Composition ...........................................................47
Specifications ..................................................................................................................48
Troubleshooting..............................................................................................................49
The Monitor Menu System ............................................................................................50
Supported Resolution ....................................................................................................52
RCA Limited Warranty....................................................................................................54
Accessories ......................................................................................................................56
Index ................................................................................................................................57
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Connections and Setup
Chapter Overview:
• Contents of the Package
• Part Names and Functions
• Battery Installation
• Connections
• A Quick Tour of the Remote Control
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
Contents of the Package
Cinema Screen monitor
Power cord
Ferrite cores
RGB cable (Mini D-Sub 15-pin to Mini D-Sub 15- pin connector)
Remote control unit with two AA batteries
User’s manual
It is highly recommended that you have your monitor installed by a professional. If you are installing
the monitor yourself, refer to the Reference section.
NOTE: If you are planning on attaching the floor stand to your monitor (and not the optional wall mount unit) you may
want to use the safety metal fittings (porvided) to give your monitor extra stability.
The safety metal fittings attach to the back of the sceren and can then be used to secuer the monitor to the wall with storng wire.
Contact your trained, authorized dealer for por fessional installation.
In order to conform to mandatory FCC standards, you must attach the supplied ferrite coers to both ends of the power
cable (see below).
If you are connecting a computer to the monito,r you must attach the ferrite coers to both ends of the DVI cable to meet
FCC standards.
Attaching the ferrite cores
Set the ferrite cores on the both ends of the DVI cable (supplied), and one end of the power cable (supplied). Close the lid
tightly until the clamps click. Use the band (supplied) to secuer the ferrite core.
DVI cable
(not supplied)
band
band
connector
core (small)
core (small)
band
power cable (supplied)
(monitor side)
core (large)
6
Chapter 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
Part Names and Functions – Front View
POWER
•
STANDBY
VOLUME
DOWN
MENU• OK
UP
LEFT/
-
RIGHT/
+
INPUT • GO BACK
VOLUME
OWN
POWER • STANDBY
MENU • OK
D
UP
LEFT/ -
RIGHT/ +
INPUT • GO BACK
1
2
3
5
6
4
1.
2.
3.
MENU•OK – If no menu is displayed, brings up the
menu. If a menu is displayed, perss to select a
highlighted option.
4.
INPUT • GO BACK – Switches the input, in the following
order:
VOLUME – Adjusts the volume. When an on-sceren
menu is being displayed, moves highlight up and down
(▲ and ▲).
*Note: You can set up CMPNT1 or RGB2, but not both.
When an on-screen menu is being displayed, returns
you to the previous menu.
LEFT/- AND RIGHT/- – When Zoom mode is on (perss OK
on the remote to turn ZOOM on and bring up the
zoom icon) press Right/+ to enlarge the image or Left/-
to reduce the image.
5. POWER/STANDBY indicator – When the power is on,
the light is green. When the power is in Standby
Mode, the light is red.
When a menu is being displayed, used to navigate
through menu ( and
).
6.
– Turns the monitor’s power on and of.
Chapter 1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
Part Names and Functions – Back View
VIDEO
VIDEO
1
2
VIDEO
3
L(MONO)
R
Y
Y
CB
PB
CR
PR
L(MONO)
R
RGB
R
1
CR
PR
G
B
Y
Y
CB
PB
H-SYNC
V-SYNC
L(MONO)
R
RGB
3
DIGITAL RGB
CONTROL
LOCK
on
off
REMOTE
CONTROL
EXTERNAL
CONTROL
VIDEO 1
VIDEO 2
3
VIDEO 3
L(MONO)
R
1
Y
Y
C
B
P
P
B
5
6
1. EXT SPEAKER L and R – Connect speakers heer.
2. AC IN – Connect the included power codr here.
3. VIDEO 1, 2, 3 – Connect VCRs, DVDs, Lasedriscs, etc. here.
4. AUDIO1, AUDIO2, AUDIO3 – Connect audio heer.
5. CMPNT1 – Connect Laser discs, etc. heer.
6. RGB1 – Connect HD receiver here.
C
R
R
L(MONO)
R
RGB 1
4
R
C
R
PR
G
B
Y
Y
C
B
PB
7
7. BNC SELECT –
H-SYNC
V-SYNC
RGB2: Inputs the analog RGB signal.
CMPNT2: Connect DVDs, Laserdiscs, etc. here.
L(MONO)
R
8. RGB3 (DVI 29pin) – Inputs a digital RGB signal.
9. CONTROL LOCK – When CONTROL LOCK is in the ON position, the buttons on the
monitor’s control panel don’t function.
RGB 3
8
DIGITAL RGB
10. REMOTE CONTROL – This jack is for connecting a wierd remote, which is primarily for
commercial applications. The remote included with your monitor is wierless and doesn’t
require connection to the monitor.
CONTROL
LOCK
9
on
off
REMOTE
CONTROL
10
11. EXTERNAL CONTROL – This terminal is used when the monitor is contorlled by external
equipment.
EXTERNAL
CONTROL
11
8
Chapter 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
Battery Installation
•
•
•
Remove the battery compartment cover from the back of the remote
control.
Insert batteries. Make sure the polarities (+ and -) aer aligned
correctly.
Replace cover.
Connecting an HD Receiver
Installing the batteries
RCA and PROSCAN HD (high definition) erceivers come equipped with an
RGB output jack for optimum quality. Using the RGB cable porvided,
connect the HD MONITOR OUT jack on the back of your HDerceiver to
the RGB1 (HD MONITOR IN)/AUDIO1 IN jack on the back of the
monitor.
If your HD receiver does not have the type of jack pictuerd on the right,
connect your HD receiver using the component video jacks and RCA
cable.
For more information on HD receiver connections, see your HD receiver
user’s manual.
The Back of the HD Receiver
RGB cable
R
R
L
ACCESS CARD
L
S-VIDEO HD MONITOR OUT
VIDEO
DIGITAL AUDIO
OUTPUT
VCR
CONTROL
AUDIO
SATELLITE
IN
OUT TO TV ANTENNA B ANTENNA A
IN IN
PHONE JACK
HD MONITOR OUT jack
Chapter 1
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
Connecting Your VCR Or Laserdisc
Player
Use common RCA cables (not provided) to connect your VCR or lasedr isc
player to your monitor. To connect your VCR or Laserdisc player:
1. Turn off the power to the monitor and VCR or laser disc playe.r
2. Connect one end of your RCA cable to the video output connector
on the back of your VCR or laser disc playe.rConnect the other end
to the video input on the monito.r
3. Use standard RCA cables to connect the audio form your VCR or
laser disc player to AUDIO2 input jacks on the monitor (if your VCR
or laser disc player has this capability). Be caerful to keep your right
and left channel connections correct for stereo sound.
RCA cables (audio/video cables) are sold as a bundled set.
4. Turn on the monitor and the VCR or laser disc playe.r
NOTE: Refer to your VCR or laser disc player user’s manual for more
information about your equipment’s video output requirements.
Connecting Your DVD Player
To connect your monitor to a DVD player:
1. Turn off the power to the monitor and DVD playe.r
2. Use a standard video cables to connect your DVD player to the CMNT1 input on the monit,or
or use the DVD player’s S-Video output. (Use a standard S-Video cable to connect to the S-
Video input on the monitor.)
3. Turn on the monitor and the DVD playe.r
Connecting a Personal Computer
If you have a computer with digital RGB output, connect it to the RGB3 jack on the monit.or
For IBM VGA (or compatible) or Macintosh (or compatible) connect to the RGB1 jack on the
monitor.
10
Chapter 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
Connecting Components to the Monitor
VIDEO 1
VIDEO 2
VIDEO 3
L(MONO)
R
VCR or Laser Disc Player
Y
Y
CB
PB
CR
PR
L(MONO)
R
DVD Player
VIDEO
VIDEO
1
2
VIDEO
3
L(MONO)
R
Signal cable (supplied)
To Mini D-Sub 15 pin connector on the
PlasmaSync 4210W
Y
Y
CB
PB
CR
PR
RGB 1
L(MONO)
R
RGB
R
1
CR
PR
G
B
Y
Y
R
CR
PR
CB
PB
H-SYNC
V-SYNC
L(MONO)
R
G
B
Y
Y
RGB
3
DIGITAL RGB
IBM VGA or Compatibles
CONTROL
LOCK
on
off
CB
PB
REMOTE
CONTROL
EXTERNAL
CONTROL
H-SYNC
V-SYNC
L(MONO)
R
Macintosh or Compatibles
Monitor adapter for Macintosh
RGB 3
DIGITAL RGB
Personal computer with a digital RGB output
CONTROL
LOCK
on
off
REMOTE
CONTROL
EXTERNAL
CONTROL
Chapter 1
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
VIDEO
VIDEO
1
2
VIDEO
3
L(MONO)
R
Y
Y
C
B
P
P
B
C
R
R
L(MONO)
R
RGB
R
1
C
R
PR
G
B
Y
Y
C
B
PB
H-SYNC
V-SYNC
L(MONO)
R
RGB
3
DIGITAL RGB
CONTROL
LOCK
on
off
REMOTE
CONTROL
EXTERNAL
CONTROL
Connecting External Speakers* to the Monitor
The monitor doesn’t have internal speakers, so in order to get sound you must connect extenral speakers. External speakers
can reproduce sound from VIDEO or RGB signal sources.
External speakers may be connected directly to the SPEAKERS terminals or indirectly by connecting a stereo system
amplifier to the audio outputs.
CAUTION: Unplug the monitor and all connected components before connecting external speakers. Use only speakers
with 6 to 8-ohm impedance and a power output rating of 7 watts or more.
To connect external speakers directly to the monitor:
1. Strip the ends of the speaker wiers.
2. Press down the tabs below the speaker temr inals and insert the speaker wire and release the tab to secure the speaker
wire connection.
[a] Connect the right speaker (located at right side of the monitor when viewed ofrm the front) positive (+) wire to
RIGHT +.
[b] Connect the right speaker negative (–) wier to RIGHT -.
[c] Connect the left speaker negative (–) wier to LEFT–.
[d] Connect the left speaker positive wire (+) to LEFT+.
*Not included
12
Chapter 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
A Quick Tour of the Remote Control
In alphabetical order
ON•OFF
VCR1
MONITOR
ANTENNA When the remote is in HD RCVR mode, switches the HD
receiver between Antenna A and Antenna B.
DVD VCR2
MUTE
AUX HD RCVR
WHO•MULTI
Arrows Use the arrows to navigate through the menu screens and moves
the Zoom pointer in Zoom mode.
AUX (auxiliary) You can program this button to control any one of the
following: a cable box; most GE, RCA, and PROSCAN audio components;
a laserdisc player; a VCR; or a satellite erceiver. Press this button to
operate the component you’ve programmed to work with the AUX button.
H
M
SLEEP
GUIDE
GO BACK
INFO
CH+/CH– Changes channels on the HD erceiver when the remote is in
HD receiver mode. When the Zoom mode is active, zooms in (CH+) or
out (CH-).
OK
O
CINEMA Press to select one of four sceren sizes to suit the type of input
you’re watching.
CLEAR
MENU
NOTE: When watching the HD receiver, screen size is controlled
through the HD receiver menu system.
3
1
4
2
CLEAR Clears on-screen displays and returns you to normal viewing.
5
8
6
CMPNT Toggles between CMPNT1 and CMPNT2 inputs.
9
7
INPUT
ANTENNA
GO BACK In HD receiver mode, returns you to the previous channel.
When in the menu system, returns you to the previous menu.
0
REVERSE
RECORD
PLAY FORWARD
GUIDE In HD receiver mode, brings up the on-screen program guide.
INFO Brings up channel information.
STOP
PAUSE
CINEMA RGB
CMPNT VIDEO
INPUT Changes the video input.
MENU Brings up the on-screen menu.
SOURCE
MONITOR Turns the power to the monitor on and puts theermote in
Monitor mode so you are able to control the monitor.
u
n
i
v
e
r
s
a
l
MUTE Reduces sound to an inaudible level.
Numbers Use the number keys to make numerical entries.
OK/ZOOM When in Monitor mode (perss the MONITOR button) and
using on-screen menus, press OK to select a highlighted menu function.
When there are no on-screen menus displayed, press OK to bring up the
zoom pointer. Using the arrow buttons, position pointer on the part of the
screen you want to zoom on, then use the CH+/- buttons to zoom in/out.
Chapter 1
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
ON•OFF Toggles power on and of for the components that you have
programmed. For example, if you are in VCR mode, turns VCR on and
off.
ON•OFF
VCR1
MONITOR
REVERSE, PLAY, FORWARD, STOP, PAUSE, RECORD (transport keys)
Use with components programmed to work with your remote control
(VCR, DVD player, audio components).
DVD VCR2
MUTE
AUX HD RCVR
WHO•MULTI
RGB Depending on how you set up the monito,rtoggles between RGB1,
RGB2*, and RGB3.
*Note: You can set up CMPNT2 OR RGB2, but not both. If CMPNT2 is
set up, RGB2 will not appear when you use the RGB button.
H
M
SLEEP Brings up the sleep time,r which is used to turn the monitor off
automatically after a set amount of time.
SLEEP
GUIDE
GO BACK
INFO
VCR1, VCR2, DVD, HD RCVR, MONITOR These are the component
buttons used to put the remote control into the correct mode to operate
that particular component. The correct video source must first be selected
(VIDEO or RGB) or Autotuning must be set up.
OK
O
CLEAR
MENU
VOL</VOL> Adjusts the volume.
3
1
4
2
VIDEO Selects whatever component is hooked up to the video soucre
inputs.
5
8
6
9
7
WHO•MULTI When in Monitor mode, activates the multi-sceren feature.
The Multi-screen feature allows you to select a sceren mode for viewing a
single picture, side-by-side pictures, or picture-in-picture (PIP). Brings up
personal viewer profiles for some components.
INPUT
ANTENNA
0
REVERSE
RECORD
PLAY FORWARD
ZOOM IN When in zoom mode (perss the MONITOR button an then
the OK button to access zoom mode) enlagres the picture. When in zoom
mode, use the arrow buttons to pan and scan the entier picture.
STOP
PAUSE
CINEMA RGB
CMPNT VIDEO
ZOOM OUT When in zoom mode (perss the MONITOR button an then
the OK button to access zoom mode) decerases the magnification of the
picture. If picture is distorted, zoom out to erstore to normal.
SOURCE
u
n
i
v
e
r
s
a
l
14
Chapter 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
Using Your Remote Control
Inserting Batteries
1. Remove the battery compartment cover from the remote control.
2. Insert batteries (included) as shown on the diagram inside the battery
compartment.
3. Replace the battery compartment cover.
Use your remote control from a distance of about 7m/23 feet form the
monitor’s remote control sensor and at a horizontal angle of within 3°0.
The remote operates on line of sight, so if theer is anything blocking the
path between the remote and the remote control sensor on the front of
the monitor, the remote may not work.
Installing the batteries
•
Don’t expose the remote control sensor on the front of the monitor
to direct sunlight or strong artificial light.
•
•
•
Don’t get the remote control wet.
Avoid heat and humidity.
When not using the remote for a long period of time, ermove the
batteries.
Programming the Remote
The universal remote control that came with your monitor is alerady
programmed to operate most RCA, GE, and PROSCAN VCRs, DVD
players, laserdisc players, and satellite receivers. This remote is also
capable of operating many other brands of ermote-controllable electronic
components, but you must program it to do so.
Find Out If You Need to Program the Remote
POWER STANDBY
INPUT SELECT
VOLUME
To determine whether the universal remote needs to be programmed,
turn on one of your components, such as a VCR. Point theermote control
at the component and press the component button (for example, the VCR
button). Now press the ON•OFF button on the ermote. If the component
doesn’t turn off, you need to program the remote control in order for it to
operate that component.
Approx.
7m/23 ft.
30° 30°
VCR1
ON OFF
MONITOR
DVD VCR2 AUX SAT CABLE
MUTE
WHO
C
H
+
V
L
L
V
C
H
-
Z
ZZ
SLEEP
GO BACK
INFO
GUIDE
OK
MENU
CLEAR
1
4
7
2
5
8
0
3
6
9
INPUT
ANTENNA
REVERSE
PLAY
FORWARD
RECORD
STOP
PAUSE
C
I
N
E
M
A
V
G
A
Y
u
v
VIDEO
SOURCE
Chapter 1
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
How to Program the Remote
There are two ways to program the remote control: automatic code search and direct entry.
Using Automatic Code Search
1. Turn on the component you want the ermote to operate (VCR, HD
receiver, etc.)
ON•OFF
VCR
1
MONITOR
2. Press and hold the component button that corersponds to the
component you want the remote to operate (VCR, HD receiver, etc.).
While you hold down the component button, perss and hold
ON•OFF (when the red light on the remote turns on, release both
buttons).
DVD VCR2
AUX HD RCVR
Note:AutomaticCodeSearchcan’tbeusedwiththeAUXbutton.
3. Press PLAY (the red light on the remote starts flashing).
The remote is searching the first set of component codes (theer are
several sets of codes). If the component you want to operate doesn’t
turn off automatically after 5 seconds, press PLAY again (the red light
starts flashing again as the remote searches through the next set of
codes).
Component Buttons
These are the buttons you program to operate another
component.
Continue pressing PLAY until the component turns off.
NOTE: If the component doesn’t turn off after you’ve pressed the PLAY
button 20 times, the component can’t be programmed.
4. Press REVERSE and wait 2 seconds. Repeat this step until the
component turns back on.
5. To finish, press and hold the STOP button until the erd light on the
remote turns off.
16
Chapter 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
Using Direct Entry
1. Turn on the component you want the ermote to operate (the red light on the remote turns
on).
2. Look up the brand and code number(s) for the component on the code list on the following
pages.
3. Press and hold the component button that corersponds to the component you want the ermote
to operate (VCR, RCA DVD, etc.).
4. Enter the code from the code list. When you begin entering numbers, theerd light on the
remote turns off. When the last number is enteerd, the red light turns back on. If the incorrect
code is entered, the red light will flash.
5. Release the component button. The red light on the remote turns off.
6. Press ON•OFF to see if the component ersponds to the remote commands. If it doesn’t, try
pressing the component button and then ON•OFF again.
6. If you get no response, repeat these steps using the next code listed for your brand, until the
component responds to the remote commands.
How To Use the Remote Control After You’ve Programmed It
Once the remote control has been programmed successfully, you’re ready to use it to operate
other components.
1. Press one of the video source buttons to select a component (VIDEO or RGB) to operate.
2. Press the component button (MONITOR, VCR, DVD, AUX, or HD RCVR) to use therTansport
buttons (REVERSE, PLAY, FORWARD, STOP, PAUSE, and RECORD) to operate the component.
3. Press ON•OFF to turn the component on or of.
NOTE: If you keep pressing buttons and nothing happens, you may have the wrong video
source or wrong component selected. You must select the correct video source and the
component button that matches the component you want to operate.
Chapter 1
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
Programmable Codes for the Remote Control
VCR (VCR1, VCR2 or AUX button)
Magnavox .......... 2021, 2022, 2062, 2063, 2104,
2108, 2124
Sylvania .... 2002, 2021, 2022, 2026, 2062, 2063,
2065, 2124
Admiral ........................................................ 2131
Adventura ................................................... 2026
Aiko ............................................................. 2027
Aiwa .................................................. 2002, 2026
Akai 2003, 2004, 2005, 2007, 2008, 2111, 2112,
2113
Magnin ........................................................ 2013
Marantz .... 2009, 2010, 2011, 2016, 2018, 2021,
2058, 2062,2064
Marta ........................................................... 2014
Masushita .................................................... 2021
MEI............................................................... 2021
Memorex ............ 2002, 2011, 2013, 2014, 2021,
2023, 2026, 2104, 2131
MGA ........................................ 2029, 2065, 2113
MGN Technology ........................................ 2013
Midland ....................................................... 2053
Minolta .................................... 2055, 2056, 2107
Mitsubishi ........... 2029, 2055, 2056, 2065, 2066,
2067, 2069, 2070, 2071, 2072, 2073, 2074, 2106,
2113, 2123
Montgomery Ward ........................... 2075, 2131
Motorola ........................................... 2021,2131
MTC ......................................... 2002, 2013, 2026
Multitech ... 2002, 2013, 2016, 2026, 2053, 2061
NEC ........... 2009, 2010, 2011, 2016, 2018, 2058,
2064, 2076, 2078, 2079, 2111, 2123
Symphonic ......................................... 2002, 2026
Tandy ................................................. 2002, 2011
Tashiko ........................................................ 2014
Tatung ............................................... 2058, 2111
TEAC .................... 2002, 2026, 2058, 2085, 2111
Technics ............................................. 2021, 2109
Teknika ...... 2002, 2014, 2021, 2026, 2100, 2129
TMK ......................................... 2013, 2024, 2047
Toshiba2015, 2049, 2051, 2055, 2065, 2093, 2116
ToteVision.......................................... 2013, 2014
Unitech ........................................................ 2013
Vector Research ............ 2009, 2010, 2015, 2016
Victor ........................................................... 2010
Video Concepts ... 2009, 2010, 2015, 2016, 2113
Videosonic ................................................... 2013
Wards ....... 2002, 2013, 2014, 2015, 2021, 2023,
2026, 2029, 2055, 2056, 2061, 2096, 2101, 2102,
2103, 2107, 2116, 2131
American High ............................................ 2021
Asha ............................................................. 2013
Audio Dynamics ................................ 2009, 2010
Audiovox ..................................................... 2014
Bell & Howell .............................................. 2011
Beaumark .................................................... 2013
Broksonic ........................................... 2012, 2025
Calix ............................................................. 2014
Candle2013, 2014, 2015, 2016, 2017, 2018, 2019
Canon ...................................... 2021, 2022, 2114
Capehart............................................ 2020, 2110
Carver .......................................................... 2062
CCE..................................................... 2027, 2061
Citizen ..... 2013, 2014, 2015, 2016, 2017, 2018,
2019, 2027
XR-1000 ................................... 2021, 2026, 2061
Yamaha ..... 2009, 2010, 2011, 2018, 2058, 2111
Zenith .................. 2004, 2098, 2104, 2119, 2128
Colortyme .................................................... 2009
Colt .............................................................. 2061
Craig .............................. 2013, 2014, 2023, 2061
Curtis-Mathes2000, 2002, 2009, 2013, 2016, 2018,
2021, 2022, 2024, 2115
Cybernex ..................................................... 2013
Daewoo2015, 2017, 2019,2025, 2026, 2027, 2028,
2110
Nikko ........................................................... 2014
Noblex ......................................................... 2013
Olympus ...................................................... 2021
Optimus ............................................. 2014, 2131
Optonica...................................................... 2096
Orion ........................................................... 2035
Panasonic .. 2021, 2022, 2109, 2125, 2126, 2127
Pentax .................. 2016, 2055, 2056, 2107, 2120
Pentex Research .......................................... 2018
Philco ............................. 2021, 2022, 2062, 2063
Philips ............................ 2021, 2062, 2096, 2124
Pilot ............................................................. 2014
Pioneer ................ 2010, 2055, 2080, 2081, 2123
Portland......................... 2016, 2017, 2019, 2110
PROSCAN ........................................... 2000, 2001
Protec .......................................................... 2061
Pulsar ........................................................... 2104
Quarter ........................................................ 2011
Quartz ......................................................... 2011
Quasar ..................................... 2021, 2022, 2125
RCA 2000, 2001, 2003, 2013, 2021, 2055, 2056,
2082, 2083, 2084, 2085, 2086, 2087, 2088, 2089,
2090, 2091, 2107, 2115, 2120, 2125
Cable Box (AUX or HD RCVR button)
ABC .. 5002, 5003, 5004, 5005, 5006, 5007, 5053
Antronix ............................................ 5008, 5009
Archer ............................ 5008, 5009, 5010, 5011
Cabletenna .................................................. 5008
Cableview .................................................... 5008
Century ........................................................ 5011
Citizen ......................................................... 5011
Colour Voice ...................................... 5012, 5013
Comtronics ........................................ 5014, 5015
Contec ......................................................... 5016
Eastern ......................................................... 5017
Garrard ........................................................ 5011
GC Electronics ............................................. 5009
Gemini ..................................... 5018, 5019, 5049
General Instrument .................................... 5003
Hamlin ................. 5020, 5021, 5022, 5035, 5045
Hitachi ......................................................... 5003
Hytex ........................................................... 5002
Jasco ............................................................ 5011
Jerrold ....... 5003, 5005, 5007,5018, 5023, 5024,
5046, 5053
Magnavox ................................................... 5025
Memorex ..................................................... 5026
Movie Time.............................. 5002, 5027, 5028
NSC .......................................... 5002, 5027, 5028
Oak ........................................... 5002,5016, 5029
Panasonic .......................................... 5048, 5052
Paragon ....................................................... 5026
Philips ....... 5011, 5012, 5013, 5019, 5025, 5030,
5031, 5032
Daytron ....................................................... 2110
Dbx .................................................... 2009, 2010
Dimensia...................................................... 2000
Dynatech ........................................... 2002, 2026
Electrohome ...................................... 2014, 2029
Electrophonic .............................................. 2014
Emerson2002, 2012,2014, 2015, 2021, 2024, 2025,
2026, 2029, 2030, 2032, 2033, 2034, 2035, 2036,
2037, 2038, 2039, 2040, 2041, 2042, 2044, 2045,
2047, 2065, 2105, 2113, 2116, 2117, 2130
Fisher ........ 2011, 2023, 2048, 2049, 2050, 2051,
2052,2118
Fuji ..................................................... 2021, 2119
Funai .................................................. 2002, 2026
Garrard ........................................................ 2026
GE2000, 2001, 2013, 2021, 2022, 2053, 2115, 2120
Goldstar ............... 2009, 2014, 2018, 2054, 2121
Gradiente .................................................... 2026
Harley Davidson .......................................... 2026
Harman Kardon .......................................... 2009
Harwood ..................................................... 2061
Headquarter ................................................ 2011
Hitachi ...... 2002, 2055, 2056, 2057, 2107, 2111,
2120, 2122
HI-Q ............................................................. 2023
Instant Replay ............................................. 2021
JCL................................................................ 2021
JC Penney 2009, 2010, 2011, 2013, 2014, 2021,
2022, 2055, 2056, 2058, 2059, 2060, 2107, 2118
Jensen ...................................... 2055, 2056, 2111
JVC ... 2009, 2010, 2011, 2018, 2058, 2111, 2123
Kenwood ............ 2009, 2010, 2011, 2016, 2018,
2058, 2111,2123
KLH .............................................................. 2061
Kodak ................................................ 2014, 2021
Lloyd .................................................. 2002, 2026
Logik ............................................................ 2061
LXI ................................................................ 2014
Radio Shack/Realistic .... 2002, 2011, 2013, 2014
2021, 2022, 2023, 2026, 2029, 2049, 2050, 2096,
2131
Radix ............................................................ 2014
Randex ......................................................... 2014
Ricoh ............................................................ 2128
Runco........................................................... 2104
Samsung .... 2005, 2013, 2015, 2033, 2053, 2112
Sanky ................................................. 2131, 2104
Sansui ............................ 2010, 2092, 2111, 2123
Sanyo ....................................... 2011, 2013, 2023
Scott 2012, 2015, 2025, 2032, 2035, 2038, 2065,
2093, 2116
Pioneer .............................................. 5033, 5034
Pulsar ........................................................... 5026
RCA .......................................... 5047, 5049, 5052
Realistic ............................................. 5009, 5049
Regal.................................................. 5022, 5035
Regency ....................................................... 5017
Rembrandt .................................................. 5003
Runco........................................................... 5026
Samsung ............................................ 5014, 5034
Scientific Atlanta .......... 5006, 5036, 5037, 5038
Signal ................................................. 5014, 5018
Sears2011, 2014, 2021, 2023, 2048, 2049, 2050,
2051, 2055, 2056, 2107, 2118
Sharp 2002, 2017, 2029, 2094, 2095, 2096, 2131
Shintom ......................... 2004, 2056, 2061, 2098
Shogun ........................................................ 2013
Signature .......................................... 2002, 2131
Singer ...................................... 2021, 2061, 2128
Sony ........... 2002, 2004, 2098, 2099, 2119, 2128
STS ..................................................... 2021, 2107
18
Chapter 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections and Setup
Signature ..................................................... 5003
SL Marx ........................................................ 5014
Sprucer ........................................................ 5052
Starcom ................................... 5007, 5018, 5053
Stargate ............................................. 5014, 5018
Starquest ..................................................... 5018
Tandy ........................................................... 5040
Teleview ...................................................... 5014
Tocom ...................................... 5004, 5023, 5041
Toshiba ........................................................ 5026
Tusa .............................................................. 5018
TV86 ............................................................. 5027
Unika ....................................... 5008, 5009, 5011
United Artists .............................................. 5002
United Cable ............................................... 5053
Universal........................ 5008, 5009, 5010, 5011
Videoway .................................................... 5044
Viewstar ........................ 5015, 5025, 5027, 5040
Zenith ...................................... 5026, 5050, 5051
Satellite Receiver
(HD RCVR or AUX button)
Audio (AUX button only)
(For RCA and Dimensia brands only)
Chapparal .......................................... 5056, 5057
Drake ................................................. 5058, 5059
GE ...................................................... 5000, 5001
General Instuments ................ 5060, 5061, 5062
Panasonic .................................................... 5075
Primestar ..................................................... 5076
PROSCAN ........................................... 5000, 5001
RCA .................................................... 5000, 5001
Realistic ....................................................... 5063
Sony ............................................................. 5072
STS1 ............................................................. 5064
STS2 ............................................................. 5065
STS3 ............................................................. 5066
STS4 ............................................................. 5067
Toshiba ........................................................ 5068
Toshiba ........................................................ 5073
Uniden ......................................................... 5069
AM/FM ......................................................... 4003
Aux .............................................................. 4004
Phono .......................................................... 4005
CD ................................................................ 4007
Tape ............................................................. 4006
Chapter 1
19
Download from Www.Somanuals.com. All Manuals Search And Download.
This page intentionally left blank.
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
The Menu System
Chapter Overview:
• Basic Operations
• The Picture Quality Menu
• The Audio Menu
• The Screen Menu
• The Function Menu
• The Options Menu
• The Setup Menu
• The Auto Tuning Menu
• The Sleep Timer
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
Basic Operations
Power
To turn the monitor on and of:
1. Plug the power cord into an active AC power outlet.
2. Press the ON•OFF button on the ermote control or the monitor button on the unit. The
monitor’s POWER/STANDBY indicator turns green when the monitor is on.
3. Press the ON•OFF button on the remote control or the unit to turn it off. The monitor’s
POWER/STANDBY indicator turns red and the standby mode is set (only when tunring off the
unit with the remote control).
Volume
To adjust the volume:
1. Press and hold the VOL > button (on theermote control or the unit) to increase to the desired
level.
2. Press and hold the VOL < button (on theermote control or the unit) to decrease to the
desired level.
Note: External speakers are required for sound.
Mute
Press the MUTE button on the ermote control to reduce the sound to an inaudible level. Perss
MUTE again to restore the sound.
Navigating the Menus
You can adjust monitor options through the monitor’s menu system. To
access the main menu, press the MENU button on the ermote control or
MENU•OK on the front of the monitor.
GUIDE
INFO
OK
O
There are a few things you need to know to navigate thorugh the menu
system. The navigation buttons are the set of arrow-shaped buttons in
the middle of the remote (See illustration on left).
CLEAR
MENU
Use the L and L buttons on the remote to move the menu highlight up
and down.
These are the buttons on the remote
you use to navigate through the
monitor’s on-screen menu system.
Use the
and
buttons to move the highlight and change settings.
Press the GO BACK button on the ermote to return to a previous menu.
You can return the monitor to the factory settings at any time by using
the RESET option in the FUNCTION menu. Remembe,rif you choose to
reset, ALL settings will return to the factory settings.
22
Chapter 6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
The Multi-Screen Feature
The Multi-Screen feature is used to show either a single pictuer or two pictures on the screen at the
same time.
SINGLE – Displays a single picture on the screen.
SIDE BY SIDE – Displays two pictuers from different input signals side-by-side.
PICTURE IN PICTURE – Displays two pictuers from different input signals; one fills the sceren and
one appears in a window on top of the other pictuer.
To use the Multi-Screen feature:
1. Press the WHO•MULTI button on the remote to select a mode.
2. If side-by-side mode or picture-in-picture mode has been selected, use the left/right arorw
buttons to position the subscreen as shown below.
Side-By-Side
Picture-in-Picture
Picture-in-picture
(window on the left):
VIDEO1 is the active
picture.
Side-by-side 1:
VIDEO1 is the
active picture.
VIDEO2
VIDEO1
VIDEO2
VIDEO1
main screen
subscreen
Picture-in-picture
(window on the right):
VIDEO1 is the active
picture.
Side-by-side 2:
VIDEO1 is the
active picture.
VIDEO2
VIDEO1
subscreen
VIDEO2
VIDEO1
main screen
subscreen
3. The active picture (indicated in the above illustrations by the double box) is the pictuerthat is
affected be remote actions and menu selections. To switch the active picture, press the OK
button. Press the OK button again to change back to the other pictuer.
Note: Changing the active picture doesn’t change the size or location of the pictures.
Chapter 6
23
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
Selecting the Input Signals to be displayed
To change the input signals displayed in multisceren operations:
1. Press the MULTI button to activate the Multiscreen function. Press the
OK button to make the desired picture active.
2. Press the RGB, VIDEO or CMPNT button to change the input signal.
The INPUT•GO BACK button on the for nt of the monitor can also
be used to change input selection.
VIDEO1
VIDEO2
VIDEO1
VIDEO2
The top screen shows VIDEO1 as the
active picture. The bottom screen shows
VIDEO2 as the active picture.
On-Screen Menu Operation
To access the main menu, press the MENU button on the ermote. The MAIN MENU is displayed on
the screen. The main menu contains a list of all the menus that conotrl your monitor. To select a
menu, use the up/down arrow buttons on the remote to highlight the desired menu. When the
desired menu is highlighted, press the OK or MENU button to select.
Note: Different components use different types of input (RGB, video, etc). Some menu
options apply to only one type of input, so they only appear when they apply to the currently
active input. For example, the COLOR and TINT options in the PICTURE QUALITY menu only
appear when you are adjusting standard video input (VIDEO1, VIDEO2, VIDEO3).
24
Chapter 6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
The Picture Quality Menu
Setting the Picture Mode with the PRESETS Option
The monitor has preset viewing modes that can be selected depending on your viewing
environment. Each preset mode has the contrast, brightness and sharpness adjusted for a specific
viewing situation.
•
•
MEMORY – This mode allows you to set and save your own pictueradjustments.
SOFT – Use this mode when watching your Monitor in a darkorom. Soft mode provides a
darker, finer picture, like the screen in movie theaters. These settings aer preset for you and
can’t be changed.
•
•
BRIGHT – Use this mode when watching your monitor in a brightorom. This mode provides a
picture with distinct differences between light and dark areas. These settings are preset for you
and can’t be changed.
NORMAL – The factory default.
To change the picture mode:
1. From the main menu, select PICTURE QUALITY. The PICTURE
QUALITY Menu will appear.
MAIN MENU
PICTURE QUALITY
AUDIO
2. Highlight the PRESETS option and press the
select it. The PRESETS window appears.
key on the remote to
SCREEN
FUNCTION
OPTIONS
3. Use the
button on the remote to select the desired mode. The
mode switches as follows when the button is pressed:
SETUP
AUTOTUNING SETUP
Note: If you don’t push the button within 5 seconds, the current
selection is set and the previous screen reappears.
SEL.
OK
EXIT
This is the main menu with the PICTURE
QUALITY option highlighted. Press OK to
bring up the highlighted menu.
Once you’ve selected the desired mode, press OK or MENU. The pictuer
mode is now set and you aer returned to the PICTURE QUALITY screen.
If you are using MEMORY mode, you can manually adjust the pictuer
settings (contrast, black level, and sharpness). You can continue adjusting
settings in the PICTURE QUALITY menu, erturn to the main menu, or
exit the menu system.
To return to the main menu, press the GO BACK button on the ermote.
To exit the menu system, press CLEAR.
Chapter 6
25
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
Adjusting the Picture Settings in MEMORY Mode
In MEMORY mode, you can set and save the following pictuer adjustments:
CONTRAST – Changes the picture’s contrast (between light and dark).
BLACK LEVEL – Makes the picture lighter or darker.
SHARPNESS – Changes the picture’s sharpness.
COLOR – Changes color density (video input only).
TINT – Changes picture tint (video input only).
COLOR TEMP – Changes the color tone.
NOISE REDUCE – (noise reduction)– Removes extraneous information from the signal to make the pictuer clearer.
NOTE: Only the contrast and brightness can be adjusted when a computer signal is used.
Once you have selected MEMORY mode, you canadjust the picture settings. For example, to change the contrast setting:
1. Use the L or L button to highlight the CONTRAST option. Perss the
button to select it. The CONTRAST window appears. Use and
buttons to adjust the contrast.
PICTURE QUALITY
CONTRAST
BLACK LEVEL
SHARPNESS
COLOR
NOTE: If you don’t push the or button within 5 seconds, the
current setting is accepted and the previous screen reappears.
R
G
TINT
2. Once the contrast is adjusted, press OK or MENU. The contrast is set
and you are returned to the PICTURE QUALITY menu.
PRESETS
: MEMORY
: NORMAL
: LOW
COLOR TEMP.
NOISE REDUCE
3. Use the same procedure to adjust the black level and sharpness
settings.
ADJ.
RETURN
SEL.
4. When you are finished adjusting the picture settings, press GO BACK
to return to the main menu or perss CLEAR to exit the menu system.
This is the PICTURE QUALITY menu with the
PRESETS option highlighted.
If the “CONTROL NOT AVAILABLE” message appears when you are
trying to change the picture settings, make sure the preset mode is set to
MEMORY. You can only change picture settings in MEMORY mode. The
other modes are pre-set and can’t be changed.
CONTRAST
This is the CONTRAST screen.
26
Chapter 6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
Setting the Color Temperature
The color temperature setting controls how warm (red) or cool (blue) your
picture is. The COLOR TEMP option has 4 settings:
Normal
Warm
Pro (lets you select settings individually)
Cool
COLOR TEMP.
: PRO
For regular viewing, Normal, Warm or Cool is recommended. The PRO
setting is generally used only for porfessional applications. To change the
COLOR TEMP setting:
This is the COLOR TEMP. screen with PRO as
the current selection.
1. From the main menu, highlight and select the PICTURE QUALITY
menu.
2. Use the arrow buttons on the remote to highlight the COLOR TEMP
WHITE BALANCE
option. Press the
appears.
button to select it. The COLOR TEMP sceren
GAIN
RED
3. Use the
and
buttons to select the desired COLOR TEMP setting.
GREEN
BLUE
BIAS
The settings switch as follows:
RED
GREEN
BLUE
NOTE: If you don’t push the or button within 5 seconds, the
current setting is accepted and the previous screen reappears.
ADJ.
RETURN
SEL.
4. Once the desired color temp is selected, press OK or MENU. If you
choose the PRO setting, the WHITE BALANCE sceren appears. It allows
individual setting of white and dark balance for each color (erd, green
and blue).
This is the WHITE BALANCE screen with the
RED GAIN option highlighted.
GAIN This adjusts the color balance for light/bright colors.
BIAS This adjusts the color balance for dark colors.
To change the white balance GAIN setting:
1. Highlight the RED, GREEN or BLUE GAIN option and perss the
button. The GAIN screen for that color appears.
2. Adjust the balance using the and
keys.
NOTE: If you don’t push the or button within 5 seconds, the
current setting is accepted and the previous screen reappears.
RED
3. When you have the desired setting, press OK or MENU. The GAIN is
adjusted and you are returned to the WHITE BALANCE screen.
This is the R-GAIN (red gain) screen.
4. When you completed all the desired white balance adjustments,
Press the GO BACK button to erturn to the PICTURE menu. You can
continue adjusting picture settings, return to the main menu or perss
CLEAR to exit the menu system.
Chapter 6
27
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
Reducing Noise in the Picture
Noise is a term used to describe extraneous bits of infomr ation in the signal that afect the
clearness of the picture. You can use the Noise Reduction (NOISE REDUCE) setting if your
reception is poor or when playing video tapes that have poor pictuer quality.
The NOISE REDUCE option has four settings, including OF.F The higher the setting, the stornger
the effect. The settings switch as follows when the button is pressed:
To change the noise reduction setting:
PICTURE QUALITY
CONTRAST
1. From the PICTURE QUALITY menu, highlight the NOISE REDUCE
option, and select it by pressing the
SCREEN is displayed.
button. The NOISE REDUCE
BLACK LEVEL
SHARPNESS
COLOR
2. Use the
setting.
and
buttons to select the desired noise reduction
R
G
TINT
PRESETS
: MEMORY
: WARM
: HIGH
NOTE: If you don’t push the or button within 5 seconds, the
current setting is accepted and the previous screen reappears.
COLOR TEMP.
NOISE REDUCE
3. When the desired setting is displayed, press OK to return to the
PICTURE QUALITY menu. You can continue adjusting picture
settings, return to the main menu, or perss CLEAR to exit the menu
system.
ADJ.
SEL.
RETURN
This is the PICTURE QUALITY menu with the
NOISE REDUCE (noise reduction) option
highlighted.
NOISE REDUCE
: HIGH
This is the NOISE REDUCE (noise reduction)
screen.
28
Chapter 6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
The Audio Menu
The AUDIO menu allows you to adjust the terble, bass and left/right balance of your extenral
speakers.
BASS – Changes the level of low ferquency sound.
TREBLE – Changes the level of high ferquency sound.
BALANCE – Changes the balance of the left and right speakers.
Menu Operations
To access the AUDIO menu:
1. From the main menu, highlight and select the AUDIO option. The
AUDIO
AUDIO menu is displayed.
BASS
2. Use the L and L arrow buttons on the remote to highlight an option
TREBLE
BALANCE
L
(for example, BASS).
R
3. Use the
and
buttons to adjust to the desierd setting.
4. You can continue adjusting audio settings, perss GO BACK to return
to the main menu, or press CLEAR to exit the menu system.
ADJ.
SEL.
RETURN
This is the AUDIO menu with the BASS option
highlighted. Press the right arrow button to
select it.
Chapter 6
29
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
The Screen Menu
The SCREEN menu allows you to set the monitor to automatically select
the correct mode for viewing a particular movie and to change the
positions of on-screen menus.
Selecting a Viewing Size
When viewing with a componentother than your HD receiver*, you can
set the screen mode to one of four sceren sizes to suit the type of input
you are watching. Select the screen mode with the CINEMA button on
the remote control. The screen sizes are as follows:
FILL expands in both vertical and horizontal dierctions while the correct
proportions are maintained. The picture is not distorted, just close.r
Fill
NORMAL displays a picture with a 4:3 aspect ratio (standadr video).
Because this mode fills the screen vertically, but not horizontally, black
bars will appear on the right and left sides of the pictuer.
Note: If viewing with a 4:3 aspect ratio for long periods of time,
set side gray level at 3 or 4.
FULL expands the picture in the horizontal direction only. This option
corrects the aspect ratio of images that have been comperssed or
horizontally “squeezed.”
STADIUM expands in both the horizontal and vertical dierctions, but
varies the amount of stretch depending on the picture – the center of the
picture is almost normal while the edges are considerably expanded.
This mode is intended for watching video with a 4:3 aspect ratio on a
wide screen.
Normal
Note: In Stadium mode, only the V-position and H-position are
displayed. You can’t change the height and width.
To change the viewing size:
1. Press the CINEMA button on the ermote control.
Full
2. The current viewing size will be displayed. Perss the CINEMA button
again to switch to the next size. The size switches as follows:
*Note: When viewing with an HD receiver, use the receiver’s screen format
selections to set the proper ratio.
Stadium
30
Chapter 6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
Adjusting the Picture Position and Size
The SCREEN menu lets you adjust the position and size of the pictuer.
The first two options, V-POSITION and H-POSITION, adjust the placement of the pictuer on the
screen. For example, if the picture is too far to the left, you can use the H-POSITION to move it to
the right. To adjust the position of the pictuer on the screen:
1. From the main menu, highlight and select the SCREEN option. The
SCREEN
SCREEN menu is displayed.
MODE
: NORMAL
2. Use the L and L buttons to select the mode you want to change.
V-POSITION
H-POSITION
V-HEIGHT
H-WIDTH
3. When the desired mode is highlighted, press the
selected mode screen will be displayed.
button. The
Use the arrow buttons to adjust the position of the pictuer.
NOTE: If you don’t push the an arrow button within 5 seconds, the
current setting is accepted and the previous screen reappears.
4. When you’ve adjusted to the desired setting, press the GO BACK
button on the remote to return to the SCREEN menu.
ADJ.
SEL.
RETURN
The SCREEN menu with the MODE option
highlighted.
The V-HEIGHT and H-WIDTH options expand and contract the size of
the picture to fill the screen. For example, if the picture is slightly wider
than the screen, you can use the H-WIDTH option to shrink the pictuer
horizontally.
Note: These options are not available in STADIUM mode.
To adjust the screen size:
1. Select the desired option from the screen menu and press the
button. The selected mode window will be displayed.
SCREEN
MODE
: FULL
2. Use the arrow buttons to adjust the size of the pictuer.
V-POSITION
H-POSITION
V-HEIGHT
H-WIDTH
NOTE: If you don’t push an arrow button within 5 seconds, the
current setting is accepted and the previous screen reappears.
3. When you’ve adjusted to the desired setting, press OK to select and
return to the SCREEN menu.
AUTO PICTURE
FINE PICTURE
PICTURE ADJ.
: OFF
ADJ.
SEL.
RETURN
Auto Picture
The AUTO PICTURE option only appears if you
have a computer connected.
The AUTO PICTURE function appears in the SCREEN menu only if you
have a computer connected to the monito.r When this feature is turned
on, it automatically adjusts flickering and striped pattenrs in a computer
image. If you want to adjust these manually:
1. Select the AUTO PICTURE option from the SCREEN menu. Press the
button to turn AUTO PICTURE off. When AUTO PICTURE is
turned off, the FINE PICTURE and PICTURE ADJ. options aer
displayed beneath it.
2. Select an option and press the
will be displayed. Use the and
button. The screen for that option
buttons to adjust that option.
Press OK to return to the SCREEN menu.
Chapter 6
31
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
The Function Menu
The FUNCTION menu contains options that contor l on-screen displays (other than the menu
system) and how the picture is displayed.
FUNCTION
On-Screen Displays
DISPLAY
: ON
: 1
On-screen displays (different than the menu system) appear by default to
give you information about an option you have selected. For example,
When you switch inputs the currently selected input name (for example,
CMPNT1) is displayed on the screen. To turn on-screen displays off:
MENU ADJUST
POWER SAVER : OFF
GRAY LEVEL
FILM MODE
RGB3 ADJ.
SCREEN SAVER
RESET
: 3
:
:
ON
1. From the main menu, highlight and select the FUNCTION option.
The FUNCTION menu is displayed.
1
2. Highlight and select the DISPLAY option. Use the button to toggle
on-screen displays on or of.
ADJ.
RETURN
SEL.
Note: Turning the DISPLAY option off does not affect on-screen
menus. Menus can’t be turned off.
3. You can continue setting options in the FUNCTION menu, perss GO
BACK to return to the main menu, or perss CLEAR to exit the menu
system.
FUNCTION
: ON
DISPLAY
MENU ADJUST
: 2
POWER SAVER : OFF
Adjusting the Position of the Menu Display
The on-screen menus can de displayed in diferent positions on the
screen. There are a total of nine possible positions shown in the grid on
the right.
GRAY LEVEL
FILM MODE
RGB3 ADJ.
SCREEN SAVER
RESET
: 3
: ON
: 1
To adjust the position of the on-sceren menus:
ADJ.
SEL.
RETURN
1. From the main menu, highlight and select the FUNCTION option.
The FUNCTION menu is displayed.
2. Highlight and select the MENU ADJUST option. Use the button to
scroll through the menu positions As you perss the
menu will move around to the different positions.
button, the
3. When you have the menu in the desierd position you can press the
L or LLarrow to select another option in the FUNCTION menu,
press GO BACK to return to the main menu, or perss CLEAR to exit
the menu system.
1 2 3
4 5 6
7 8 9
The number 2 position will display on-screen
menus in the top center of your screen.
32
Chapter 6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
FUNCTION
: ON
Setting the POWER SAVER for Computer Images
DISPLAY
The POWER SAVER function can be used when the signal soucre to the
monitor comes from a computer conforming to the VESA DPMS format.
This function automatically reduces the monitor’s power consumption if
no operation is performed for a certain amount of time. POWER SAVER
can be turned on or off.
MENU ADJUST
: 1
POWER SAVER : ON
GRAY LEVEL
FILM MODE
RGB3 ADJ.
SCREEN SAVER
RESET
: 3
: ON
: 1
If the computer’s power isn’t turned on or if the computer and selector
tuner are not properly connected, POWER SAVER is set to OFF.
For instructions on using the computer’s power management function,
see your computer’s operating manual.
ADJ.
SEL.
RETURN
This is the FUNCTION menu with the POWER
SAVER option highlighted.
To turn the monitor’s POWER SAVER function on or of:
1. From the main menu, highlight and select FUNCTION. The
FUNCTION menu is displayed.
2. Highlight the POWER SAVER option.
3. Use the
button to toggle the setting ON or OF.F
4. You can continue making adjustments in the FUNCTION menu,
return to the previous menu by pressing the GO BACK button or
press CLEAR to exit the menu system.
The POWER/STANDBY indicator shows the status of the POWER SAVER
function. See below for status and description.
POWER/STANDBY indicator
POWER
SAVER
Mode
POWER/
STANDBY
indicator
Power Saver
Operating Status
Description
Turning the Picture Back On
Picture already on.
On
Green
Yellow
Red
Not activated
Horizontal and vertical
synchronizing signals are
present from the computer.
Standby
Suspend
Off
Activated
No horizontal synchronizing
signals are present from the
computer.
Use the keyboard or mouse.
The picture reappears immediately.
Activated
No vertical synchronizing signals
are present from the computer.
Use the keyboard or mouse. The
picture reappears, but more slowly
than when in standby mode.
Red
Activated
No horizontal and vertical
synchronizing signals are present
from the computer.
Use the keyboard or mouse. The
picture reappears, but more slowly
than when in either standby or
suspend mode.
Chapter 6
33
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
FUNCTION
Setting the Gray Level for the Sides of the Screen
DISPLAY
: ON
: 1
The GRAY LEVEL function allows you to set the gray level for the sides of
the screen where nothing is displayed (on the left and right sides of the
screen when it is set to 4:3 size). The level can be adjusted ofrm 0 to 15.
The factory setting is 3 (dark gray).
MENU ADJUST
POWER SAVER : OFF
GRAY LEVEL
FILM MODE
RGB ADJ.
: 9
:ON
:1
NOTE: Repeated watching with the gray level set to black may effect
the quality of your picture. To reduce the effects of uneven phosphor
aging, set the gray level to 3 or 4.
SCREEN SAVER
RESET
To adjust the gray level for the sides of the sceren:
ADJ.
SEL.
RETURN
1. From the main menu, highlight and select FUNCTION. The
FUNCTION menu is displayed.
This is the FUNCTION menu with the GRAY
LEVEL option highlighted.
2. Highlight the GRAY LEVEL option.
3. Use the
button to scroll through the levels.
NOTE: Repeated watching with the
gray level set to black may effect the
quality of your picture. To reduce the
effects of uneven phosphor aging, set
the gray level to 3 or 4.
4. When the desired gray level is highlighted, press the
button to
return to the FUNCTION menu options. You can continue making
adjustments within the FUNCTION menu, press GO BACK to return to
the previous menu or press CLEAR to exit the menu system.
If viewing with a 4:3 aspect ratio
for long periods of time, set side
gray level at 3 or 4.
Adjusting for Flickering with Film Mode
There is some amount of flickering that occurs in an image when it is
transferred from film to video.
ON All images are displayed in film mode.
OFF Film mode is of.
To turn FILM MODE ON:
FUNCTION
1. From the main menu, highlight and select FUNCTION. The
FUNCTION menu is displayed.
DISPLAY
: ON
: 1
MENU ADJUST
2. Highlight the FILM MODE option.
POWER SAVER : OFF
3. Use the
displayed.
button to scroll through the three modes until ON is
GRAY LEVEL
FILM MODE
RGB3 ADJ.
SCREEN SAVER
RESET
: 3
: ON
:
1
4. Press the
button to return to the FUNCTION menu options. You
can continue making adjustments within the FUNCTION menu, erturn
to the previous menu by pressing GO BACK or press CLEAR to exit
the menu system.
ADJ.
RETURN
SEL.
This is the FUNCTION menu with the FILM
MODE option highlighted.
34
Chapter 6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
FUNCTION
: ON
Adjusting the Monitor in RGB3 Input Mode
If the picture is not stable in RGB3 mode, use the RGB3 ADJUST featuer
to adjust it.
DISPLAY
MENU ADJUST
: 1
POWER SAVER : OFF
1. From the main menu, highlight and select OPTIONS. The OPTIONS
menu is displayed.
GRAY LEVEL
FILM MODE
RGB3 ADJ.
SCREEN SAVER
RESET
: 3
: ON
2. Highlight the RGB3 ADJUST option.
:
1
3. Use the
button to select the desired adjustment (1, 2 or 3). The
choices scroll as follows:
ADJ.
RETURN
SEL.
This is the FUNCTION menu with the RGB3
ADJ. option highlighted.
4. When the desired number is selected, press the
button to return to
the FUNCTION menu items. You can continue making adjustments
within the FUNCTION menu, press GO BACK to return to the
previous menu or press MENU or CLEAR to exit the menu system.
Note: When AUTO PICTURE is on, switch it off and back on again
to return the display position to its original position.
Setting the SCREEN SAVER
The SCREEN SAVER option contains three features in one. These features
are used principally for PC operation.
FUNCTION
DISPLAY
: ON
: 1
MENU ADJUST
The PLE (Peak Luminance Enhancement) function sets the luminance
level to a fixed mode to erduce the effects of phosphor aging.
POWER SAVER : OFF
GRAY LEVEL
FILM MODE
RGB3 ADJ.
SCREEN SAVER
RESET
: 3
The ORBITER (Peak Luminance Enhancement) moves the image aorund
the screen intermittently to reduce the effects of phosphor aging.
: ON
:
1
The INVERSE function works in RGB mode only. INVERSE inverts the
video signal, playing the image in a negative fomr at.
ADJ.
RETURN
SEL.
Setting the PLE
PLE has two options:
This is the FUNCTION menu with the SCREEN
SAVER option highlighted.
AUTO – luminance level (contrast) is nomr al.
LOCK – dims picture to reduce phosphor aging.
The factory setting is AUTO. Setting the PLE option to LOCK dims the
picture – the contrast will be lower than nomr al.
Setting PLE to LOCK is
recommended if you are displaying
stationary pictures.
To set the PLE level to LOCK:
1. From the main menu, highlight and select FUNCTION. The
FUNCTION menu is displayed.
2. Highlight the PLE option.
3. Use the
button to select LOCK.
4. Press the
button to return to the FUNCTION menu options. You
can continue making adjustments within the FUNCTION menu,
return to the previous menu or press MENU or CLEAR to exit the
menu system.
Chapter 6
35
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
SCREEN SAVER
Turning ORBITER on
The factory setting for ORBITER is OFF. To turn ORBITER ON:
PLE
: AUTO
: ON
ORBITER
INVERSE
1. From the main menu, highlight and select FUNCTION. The
FUNCTION menu is displayed.
: OFF
2. Highlight the SCREEN SAVER option (the SCREEN SAVER menu is
displayed).
3. Highlight the ORBITER option.
4. Use the
button to select ON.
5. Press the
button to return to the FUNCTION menu options. You
ADJ.
RETURN
SEL.
can continue making adjustments within the FUNCTION menu,
return to the previous menu or press MENU or CLEAR to exit the
menu system.
This is the SCREEN SAVER menu with the
ORBITER option highlighted.
Setting the INVERSE
INVERSE has three options:
ON – The picture is alternatively displayed as a positive and negative
image.
OFF – INVERSE is of.
WHITE – The screen turns white.
The factory setting is OFF. To change the INVERSE mode:
1. From the main menu, highlight and select FUNCTION. The
FUNCTION menu is displayed.
2. Highlight and select the SCREEN SAVER option.
3. Highlight the INVERSE option.
4. Use the
button to select your choice.
5. Press the
button to return to the FUNCTION menu options. You
can continue making adjustments within the FUNCTION menu,
return to the previous menu or press MENU or CLEAR to exit the
menu system.
36
Chapter 6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
RESET
Resetting to Default Values
RESET
The RESET function allows you to erset all adjustments to the factory
default settings. Caution: this will reset all adjustments you have
made in all menus, including autotuning configuration settings.
RETURN
To reset to the factory default settings:
1. From the main menu, highlight and select FUNCTION. The
FUNCTION menu is displayed.
2. Highlight the RESET function and press OK.
3. The RESET screen is displayed.
SEL.
RETURN
OK
4. Use the L or L button to highlight the RESET option and perss OK
or MENU. The RESET screen will display the message NOW
RESETTING. When the settings are restored to the factory default
you are returned to the RESET screen.
RESET
When you are done, press GO BACK to return to the FUNCTION menu
or pres CLEAR to exit the menu system.
NOW RESETTING
These are the RESET screens. Choose the
RESET option if you want to reset ALL
options in all menus back to the factory
default.
Chapter 6
37
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
The Options menu
Setting the Audio Inputs
The monitor’s audio sources are programmable to the each of the monitor’s video soucres. For
example, you can program AUDIO1 source to work with the RGB2 video soucre.
This feature is generally used only for commecrial applications.
1. From the main menu, highlight and select OPTIONS. The OPTIONS
OPTIONS
AUDIO INPUT
menu is displayed.
AUDIO1
: RGB1
: VIDEO1
: CMPNT1
: RGB2
: RGB
2. Highlight the one of the audio input options.
AUDIO2
3. Use the
button to scroll through the available video sources. The
AUDIO3
modes scroll as follows:
BNC SELECT
RGB SELECT
HD SELECT
PICTURE SIZE
: 1080A
:
ON
4. When the desired mode is selected, press the
button to return to
the OPTIONS menu items. You can continue making adjustments
within the OPTION menu, press GO BACK to return to the previous
menu or press MENU or CLEAR to exit the menu system.
SEL.
ADJ.
RETURN
This is the OPTIONS menu with the AUDIO1
input option highlighted.
The factory defaults are as follows:
• AUDIO1 – VIDEO1
• AUDIO 2 – CMPNT1
• AUDIO3 – RGB1
If you use the reset option in the FUNCTION menu, the settings will
return to the factory default settings listed above.
OPTIONS
AUDIO INPUT
AUDIO1
: VIDEO1
: CMPNT1
: RGB1
Setting the BNC Connectors
AUDIO2
AUDIO3
If the component you are connecting to the monitor doesn’t have
composite video jacks, you can set the BNC inputs to act as component
video inputs.
BNC SELECT
RGB SELECT
HD SELECT
PICTURE SIZE
: CMPNT2
: RGB
: 1080A
1. From the main menu, highlight and select OPTIONS. The OPTIONS
menu is displayed.
:
ON
ADJ.
SEL.
RETURN
2. Highlight the BNC SELECT option.
This is the OPTIONS menu with the BNC
SELECT option highlighted.
3. Use the
button to toggle between RGB2 (composite) and
CMPNT2. (component).
4. Once you’ve selected the desired setting, press the
button to
return to the OPTIONS menu items or perss CLEAR to return to the
main menu.
38
Chapter 6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
Setting a Computer Image to the Correct RGB
Select Mode
The RGB SELECT function allows you to select the corerct viewing mode
for the type of computer image you aer displaying.
The RGB SELECT function has six modes:
AUTO – Automatically selects the most suitable mode for displaying the
input signal.
STILL – Use this mode to display VESA standadr signals (still image from a
computer).
MOTION – Use this mode for moving images form a computer. Converts
the signal to RGB signal for best viewing.
WIDE1– Prevents horizontal compression when the input signal is 852 dot
X 480 line signal with a horizontal ferquency of 31.7kHz.
WIDE2 – Prevents horizontal compression when the input signal is 848
dot X 480 line signal with a horizontal ferquency of 31.0kHz.
DTV – This mode is primarily used to optimize pictuer quality if you are
using a generic-brand DTV receiver which outputs signal at 480P
(progressive scan) lines.
To change the RGB SELECT mode:
OPTIONS
AUDIO INPUT
1. From the main menu, highlight and select the OPTIONS menu. The
OPTIONS menu is displayed.
AUDIO1
: VIDEO1
: CMPNT1
: RGB1
AUDIO2
2. Highlight the RGB SELECT option.
AUDIO3
3. Use the
button to scroll through the mode choices. The settings
BNC SELECT
RGB SELECT
HD SELECT
PICTURE SIZE
: RGB2
switch as follows:
: AUTO
: 1080A
AUTO
STILL
MOTION
WIDE1
WIDE2
DTV
:
ON
ADJ.
RETURN
SEL.
4. When the desired mode is selected, press the
button to return to
This is the OPTIONS menu with the RGB
SELECT option highlighted.
the OPTIONS menu items. You can continue making adjustments
within the OPTIONS menu, press GO BACK to return to the previous
menu or press CLEAR to exit the menu system.
Chapter 6
39
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
Setting the Monitor to the correct HD Receiver Mode
The HD SELECT function allows you to select the corerct mode for the monitor to work with your
HD receiver. The default setting is 1080A. This is the corerct setting for all RCA and PROSCAN HD
receivers. If you have another brand of HD erceiver, your picture may appear broken or off-center.
If so, you need to switch HD SELECT modes.
1080A – Use this option for RCA or PROSCAN HDerceivers.
1080B – Use this option if you have any other brand of HDerceiver.
To change the receiver mode:
1. From the main menu, highlight and select OPTIONS. The OPTIONS menu is displayed.
2. Highlight the HD SELECT option.
OPTIONS
AUDIO INPUT
3. Use the button to select the desired mode (1080 A or 1080 B).
AUDIO1
: VIDEO1
: CMPNT1
: RGB1
: RGB2
: RGB
4. When the desired number is selected, press the button to return to
the OPTIONS menu items. You can continue making adjustments
within the OPTIONS menu, press GO BACK to return to the previous
menu or press MENU or CLEAR to exit the menu system.
AUDIO2
AUDIO3
BNC SELECT
RGB SELECT
HD SELECT
PICTURE SIZE
: 1080A
ON
Setting the Picture Size for RGB Input
ADJ.
SEL.
RETURN
The PICTURE SIZE option is used to adjust the pictuer size when the
input signal is RGB. Use this featuer for graphic arts and checking
photos. In TRUE mode, there is no distortion of the pictuer. In NORMAL
mode, the picture will be scaled vertically but will keep the corerct
aspect ratio.
This is the OPTIONS menu with the HD
SELECT option highlighted.
OPTIONS
ON – When the picture size option is on and in NORMAL mode, the
picture is scaled to fill the sceren vertically while horizontally keeping the
correct aspect ratio. In FULL mode, the horizontal will be scaled to fit the
screen.
AUDIO INPUT
AUDIO1
: VIDEO1
: CMPNT1
: RGB1
: RGB2
: RGB
AUDIO2
AUDIO3
BNC SELECT
RGB SELECT
HD SELECT
PICTURE SIZE
OFF – When the picture size option is of, TRUE mode displays the
picture pixel-for-pixel, exactly the size of the image. If FULL mode, the
image is scaled to fit the sceren.
: 1080A
:
ON
Note: When using a DTC100 HD receiver, the only available mode is
FULL. The picture will be scaled to fill the screen.
ADJ.
SEL.
RETURN
This is the OPTIONS menu with the PICTURE
SIZE option highlighted.
40
Chapter 6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
The Setup Menu
The SETUP menu controls the way your monitor communicates.
Confirming the Frequencies, Polarities, Mode and Resolution of
Input Signals
The FREQUENCY function is used to confimr the frequencies, polarities, mode and resolution of
the signals coming from a computer.
To confirm frequencies, polarities, mode and resolution:
1. From the main menu, highlight and select the SETUP option. The
SETUP
SETUP menu is displayed.
FREQUENCY
2. Highlight the FREQUENCY option and press OK.
3. The FREQUENCY screen is displayed.
MENU LANGUAGE
COLOR SYSTEM
Press GO BACK to return to the SETUP menu, or perss CLEAR to exit
the menu system.
RETURN
OK
SEL.
This is the SETUP menu with the FREQUENCY
option highlighted.
FREQUENCY
H. FREQUENCY : 37.5KHz
V. FREQUENCY : 75.0Hz
H. POLARITY
V. POLARITY
: NEG.
: NEG.
MODE
:
:
8
RESOLUTION
640 X 480
RETURN
This is the FREQUENCY screen.
Chapter 6
41
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
Selecting the Language for the Menus
The menu display can be set to one of there languages: English, French or Spanish. The default is
English. To change the default setting:
1. From the main menu, highlight and select the SETUP option. The
MENU LANGUAGE
LANGUAGE
SETUP menu is displayed.
2. Highlight the MENU LANGUAGE option. The MENU LANGUAGE
screen is displayed.
˜
: ESPANOL
3. Use the
button to scroll through the language choices. The
settings switch as follows:
4. When the desired language is highlighted, press GO BACK to return
to the SETUP menu. You can continue making adjustments within
the SETUP menu, press GO BACK to return to the main menu, or
press CLEAR to exit the menu system.
ADJ.
OK
RETURN
This is the MENU LANGUAGE screen with
Spanish as the selected language.
Setting the Video Signal Format
The COLOR SYSTEM option is used to set the video signal fomrat.
Different countries used different formats for video signals. The AUTO
option automatically detects the correct video signal and sets the corerct
format. This setting should not be changed.
42
Chapter 6
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
The Autotuning Menu
Autotuning the Component buttons on the Remote Control
The AUTOTUNING feature lets you easily program the component buttons on the ermote to operate
the components hooked up to the monito.rTo autotune your components to the buttons on the
remote:
1. From the main menu, highlight and select the AUTOTUNING SETUP
AUTOTUNING SETUP
option. The AUTOTUNING SETUP menu is displayed.
HD RCVR BTN
: RGB1
2. Highlight an option which corresponds to a component which
you’ve connected. For example, if you have a DVD player
connected, highlight the DVD BUTTON option.
AUX BUTTON
VCR1 BUTTON
DVD BUTTON
: NONE
: VIDEO1
: CMPNT1
3. Use the
button to scroll through the output choices. Select the
choice which corresponds to the jacks you used to connect the DVD
player. In the example illustration on the right, the DVD button on
the remote will operate the component connected to the CMPNT1
jacks (the DVD player).
SEL.
ADJ.
RETURN
4. When the desired option is displayed, press the
button to return
This is the AUTOTUNING SETUP menu with
the DVD BUTTON option highlighted.
to the AUTOTUNING menu options. You can continue making
adjustments within the OPTIONS menu, press GO BACK to return to
the previous menu or press CLEAR to exit the menu system.
Chapter 6
43
Download from Www.Somanuals.com. All Manuals Search And Download.
The Menu System
Sleep Timer
The sleep timer is a feature that allows you to set the monitor to tunr off after a prescribed amount
of time. It can be set to tunr the power off after 30, 60, 90 or 120 minutes.
Setting the Sleep Timer
1.Press the SLEEP button on the ermote to turn on the timer. The default is 30 minutes.
2.Press the SLEEP button again to move to the next time incerment. Press the SLEEP button
until you get to the desired time.
3.The timer starts when the Sleep display disappears form the screen.
To check the Remaining Time:
1.Once the sleep timer has been set and the menu has tunred off, press the SLEEP button
once.
2.The remaining time is displayed, then disappears after a few seconds.
3.When five minutes remain, the remaining time appears until it reaches zero.
Cancelling the Sleep Timer
1.Press the SLEEP button twice in a orw.
2.The sleep timer is canceled.
NOTE: After the power is turned off with the sleep timer, a slight current is still supplied
to the monitor. If you do not plan to use the system for a long period of time, tnurthe
power off with the remote or on the unit.
44
Chapter 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Other Information
Chapter Overview:
• Installation
• Connecting Your PC or Macintosh
Computer
• Specifications
• Troubleshooting
• The Menu System
• Supported Resolution
• Limited Warranty
• Accessory Information
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
REFERENCE
Installing the Cinema Screen Monitor
IMPORTANT
• This device cannot stand on its own. Be sure to use a stand or original mounting unit.
• For correct installation and mounting it is strongly recommended to use a trained, authorized Cinema Screen
dealer.
Failure to follow correct mounting procedures could result in damage to the equipment or injury to the installer.
Product warranty does not cover damage caused by improper installation.
Attaching optional mounts or stand to the Cinema Screen monitor
The Cinema Screen monitor can be mounted on the wall using an optional wall mount or you can attach a floor stand (also
optional). For more information on mounting your Cinema Screen Display, see your Cinema Screen dealer.
If you choose to use the optional wall mount, it can be attached to the Cinema Secern monitor in one of the following two
ways:
• While it is upright.
• While it is laying with the sceren face down. If you choose this option, lay the portective sheet that came wrapped
around the monitor beneath the screen surface so it doesn’t get scratched.
Ventilation requirements for enclosure mounting
To allow heat to disperse, leave space between surorunding objects as shown on the diagram below when installing.
WALL
50mm (2”)
50mm (2”)
1240mm (48.8”)
WALL
50mm (2”)
46
Chapter 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
REFERENCE
Connecting Your PC Or Macintosh
Computer
Mini D-sub 15 Pin VGA Signal
Composition
Connecting your PC or Macintosh computer to your
Cinema Screen monitor will enable you to display
computer images on the monitor. The Cinema Screen
monitor supports the signals described on page 48.
5
4
3
2
1
9
8
7
6
10
15 14 13 12 11
To connect to a PC, Macintosh or compatible graphics
adapter:
1. Turn off the power to your monitor and compute.r
2. If your PC does not support XGA/SVGA/VGA you will
need to install an XGA/SVGA/VGA graphics board.
Consult your computer’s owner’s manual for your SXGA/
XGA/ SVGA/VGA configuration. If you need to install a
new board, see the manual that comes with your new
graphics board for installation instructions.
Pin No.
Signal to be connected
RED
1
2
GREEN or sync. on Green
BLUE
3
3. The Cinema Screen monitor provides signal
compatibility with VESA 128021024@60MHz (SXGA).
However, we recommend not using this resolution due to
image readability on the monitor’s 853 X 480 native pixel
resolution panel.
4
No connection
GND
5
6RED
7
(GND)
4. Use the signal cable that’s supplied to connect your
PC or Macintosh computer to the Cinema Sceren monitor.
For Macintosh, you will need a monitor adapter (not
supplied) to connect to your computer’s video port.
GREEN (GND)
BLUE (GND)
No connection
SYNC (GND)
No connection
SDA
8
9
5. Turn on the monitor and the compute.r
10
11
12
13
14
15
6. If the Cinema Screen monitor goes blank after a
period of inactivity, it may be caused by a sceren saver
installed on the computer you’ve connected to the
monitor.
H. Sync
When using a Macintosh with the Cinema Sceren
monitor, the following three display standards are
supported using the included Macintosh adapter : 13" fixed
mode, 16" fixed mode, and 19" fixed mode. The 13" fixed
mode is recommended for the Cinema Screen monitor.
V. sync
SCL
Chapter 7
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
REFERENCE
Specifications
Product Name
1.89”
48.8”
43.5”
2.31”
PHD50300 Cinema Screen Monitor
43.5"(H) X 24.5"(V) inches
1106(H) X 622(V)mm
Screen Size
diagonal 50"
Aspect Ratio
16 : 9
Resolution
1365(H) X 768(V) pixels
256 levels, 16,770,000 colors
RGB, NTSC (3.58 4.43), PAL (B, G, M, N),
PAL60, SECAM, HD*1, DVD*1, DTV*
Color Reproduction
Input Signals
RGB Input terminals
RGB 1
4.2”
mini D-sub 15-pin
RGB 2
BNC (R, G, B, H/CS, V) X1
DVI-I 29-pin X 1*2
RGB 3
The features and specifications may be subject to change
without notice.
Video Input terminals
Video 1
Video 2
RCA-pin X 1
BNC X 1
* HD/DVD/DTV input signals supported on this system
Video 3
S-Video: DIN 4-pin X 1
RCA-pin (Y, PB[CB], PR[CR])
Stereo RCA X 3
DVD/HD/DTV
480P (60 Hz)
525P (60 Hz)
625P (60 Hz)
720P (60 Hz)
480I (60 Hz)
525I (60 Hz)
625I (60 Hz)
720I (60 Hz)
1080I (60 Hz)
Audio
External Control
Sound Output
D-sub 9-pin X1 (RS-232C)
7W+7W at 6 ohm
Power Supply
AC120V 50/60Hz
Current Rating
5.9A (maximum)
Power Consumption
Dimensions (WxDxD)
595W (typical)
1240 X 766 X 107mm (w/o stand)
48.8 X 30.2 X 4.2 inches (w/o stand)
1240 X 826 X 400mm (with stand)
46 Kg/101.3 lbs. (w/o stand)
Net Weight
Environmental Considerations
Operating temperature
Humidity
0°C to 35°C/32°F to 95°F
20 to 80%
Altitude
0 to 1900m/0 to 6230 ft.
Storage temperature
Humidity
-10°C to 50°C/14°F to 122°F
10 to 90%
Front Panel User Controls
Power on/off, Input source select
Volume up/down/OSD control
Power Management, plug and play (DDCI,
DDC2b, RGB3: DDC2b only)
Remote control with two AA batteries, RGB
cable (Mini D-sub 15 pin to Mini D-sub 15-pin
connector), power cord, safety metal fitting,
screw for safety metal fitting, User’s Manual
UL approved (UL 1950, CSA 950)
DOC Canada requirements
Other Features
Accessories
Regulations
Meets FCC class B requirements for home
application
48
Chapter 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
REFERENCE
Troubleshooting
Before requesting service, check the adjustments, operations, etc.
Symptom
Possible Problem
Solutions
• Is a connected component set directly in front
or at the side of the monitor?
Picture is disturbed.
• Leave some space between the display and
connected components.
Sound is noisy.
Remote control unit operates erroneously.
• Remote control batteries may be dead.
• Remote may be in wrong mode.
The remote control does not work.
• Replace both batteries with new ones.
• Press component button for desired component.
• Is the monitor’s power cord plugged into a
power outlet?
Monitor’s power does not turn on when the
remote control’s power button is pressed.
• Plug the monitor’s power cord into a power
outlet.
• Are all the monitor’s indicators off?
• Press the power button on the monitor to turn
on the power.
• Is the remote control pointed at the monitor,
or is there an obstacle between the remote
control and the monitor?
Monitor does not operate when the remote
control’s buttons are pressed.
• Point the remote control at the monitor’s
remote control sensor when pressing buttons,
or remove the obstacle.
• Is direct sunlight or strong artificial light
shining on the monitor’s remote control
sensor?
• Eliminate the light by closing curtains, pointing
the light in a different direction, etc.
• Remote control batteries may be dead.
• Replace both batteries with new ones.
• Is the monitor’s power cord plugged into a
power outlet?
No sound or picture is produced.
• Plug the monitor’s power cord into a power
outlet.
• Is the source video connected and on?
• Make sure source video (VCR, DVD, DTC) is
connected and turned on.
• Is the volume set at the minimum?
• Is the mute mode set?
Picture appears but no sound is produced.
• Increase the volume.
• Press the remote control’s mute button.
• Connect the speakers properly.
• Are the speakers properly connected?
• Are the tint and colors properly adjusted?
Tint is poor or colors are weak.
Nothing appears on screen.
• Adjust the tint and color (under PICTURE).
• Return to factory reset.
• Is the computer’s power turned on?
• Is a video source connected?
• Turn on the computer’s power.
• Connect video source to the monitor.
• Operate the computer (move the mouse, etc.).
• Is the power manager function in the
STANDBY or OFF mode?
• Is the picture position adjusted correctly?
Part of picture is cut off or picture is
not centered.
• Adjust the picture from the SCREEN menu.
• Is the screen size adjusted correctly?
Image is too large or too small.
• Press the WIDE/AUTO WIDE button on the
remote control and adjust properly.
• Is the computer set at the correct resolution?
• Is the HD receiver set to the correct mode?
Picture is unstable.
• Set to the proper resolution.
• Set HD receiver to the correct mode (page 29).
Chapter 7
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
REFERENCE
The Monitor Menu System
Main menu
Sub menu
CONTRAST
BLACK LEVEL
SHARPNESS
COLOR
Functions
PICTURE QUALITY
Adjusts the contrast.
Adjusts the brightness.
Adjusts the sharpness.
Adjusts the color density (video input only).
Adjusts the picture tint (video input only).
Sets the picture mode according to the video environment.
Adjusts the color temperature and white balance.
Reduces noise visible in image.
TINT
PRESETS
COLOR TEMP.
NOISE REDUCE
Sub menu
BASS
Main menu
Functions
AUDIO
Sets the bass.
TREBLE
Sets the treble.
BALANCE
Sets the left/right balance.
Main menu
Sub menu
V-POSITION
H-POSITION
V-HEIGHT
Functions
SCREEN
Adjusts the vertical picture position of the picture on the screen.
Adjusts the horizontal picture position of the picture on the screen.
Adjusts the vertical size of the picure.
Adjusts the horizontal size of the picure.
When turned on, automatically adjusts for flickering and striped patterns.
Adjusts for flickering in the picture.
Adjusts for striped patterns in the picture.
Functions
H-WIDTH
AUTO PICTURE
FINE PICTURE
PICTURE ADJ.
Sub menu
DISPLAY
Main menu
FUNCTION
Turns the on-screen display on and off.
Adjusts the vertical and horizontal position of the menu display.
Sets the monitor for use as an energy-saving display when used with a computer.
MENU ADJUST
POWER SAVER
GRAY LEVEL
When viewing a picture with 4:3 aspect ratio, sets the luminance of both sides of
the picture.
FILM MODE
When turned to AUTO, selects the correct viewing format.
Adjusts the display position in RGB3 input.
RGB3 ADJUST
SCREEN SAVER
Used principally for PC operation.
PLE sets the luminance level to a fixed mode to reduce the effects of
phosphor aging.
ORBITER moves the image around the screen intermittantly to reduce the
effects of phosphor aging.
INVERSE works in RGB mode only. Inverts the video signal, playing the image
in a negative format.
RESET Resets ALL the settings to the factory default values.
50
Chapter 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
REFERENCE
Main menu
Sub menu
Functions
OPTIONS
AUDIO INPUT
BNC SELECT
RGB SELECT
Allocates audio connectors.
Sets BNC connectors to either composite or component video.
Sets the appropriate mode for the computer image.
RGB (VGA signals), VIDEO (Moving picture), WIDE (WIDE VGA) DTV.
HD SELECT
Sets correct mode for your HD digital receiver (1080 A or 1080 B).
Sets the picture size for RGB input.
PICTURE SIZE
Main menu
Sub menu
Functions
SETUP
FREQUENCY
Confirms the frequency and synchronizing polarities of the signal currently
being inputted.
MENU LANGUAGE Sets the language of the menus (English, French, or Spanish)
COLOR SYSTEM
Sets the VIDEO format. Keep this set to AUTO.
Main menu
Sub menu
Functions
AUTOTUNING SETUP
HD RCVR BTN
Autotunes the HD RCVR button on the remote control to the input that
your HD receiver is hooked up to.
AUX BUTTON
VCR1 BUTTON
DVD BUTTON
Autotunes the SAT2 button on the remote control to the input that your
satellite receiver is hooked up to.
Autotunes the VCR button on the remote control to the input that your
VCR is hooked up to.
Autotunes the DVD button on the remote control to the input that your
DVD player is hooked up to.
Chapter 7
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
REFERENCE
Supported Resolution
• When screen mode is NORMAL, each signal is converted to 640 dot X 480 line signal (except for *3).
• When screen mode is FULL, each signal is converted to 853 dot X 480 line signal (except for *2).
Notes:
• With Digital inputs some signals are not accepted.
• The sync may not be disturbed when non-standard signals other than the previously mentioned are input.
• When connecting a composite sync signal, use the HD terminal.
Screen mode
Vertical
Sync Polarity
Horizontal Vertical Horizontal
Presence
Vertical
RGB
Horizontal
select*5
Dots X lines
frequency frequency
Model
NORMAL
TRUE
FULL
(16:9)
(kHz)
(Hz)
(4:3)
640 X 400
640 X 480
70.1
59.9
72.8
75.0
85.0
100.4
120.4
60.0
60.0
56.3
60.3
72.2
75.0
85.1
99.8
120.0
60.0
70.1
75.0
85.0
100.6
75.0
56.2
60.0
59.9
60.0
75.0
85.0
60.0
65.0
70.0
75.0
66.7
74.6
74.9
75.1
60.0
71.2
72.0
31.5
31.5
37.9
37.5
43.3
51.1
61.3
31.0
31.7
35.2
37.9
48.1
46.9
53.7
63.0
75.7
48.4
56.5
60.0
68.7
80.5
67.5
45.1
47.7
48.3
64.0
80.0
911
NEG
NEG
NEG
NEG
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
– –
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
– –
YES*2
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
YES
YES
– –
– –
– –
– –
– –
– –
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES*3
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
– –
STILL
– –
STILL
– –
NEG
NEG
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
NEG
NEG
NEG
NEG
NEG
NEG
– –
– –
NEG
NEG
848 X 480
852 X 480*1
800 X 600
POS
POS
WIDE2
WIDE1
STILL
STILL
– –
– –
– –
– –
– –
STILL
– –
STILL
– –
NEG
NEG
POS
POS
POS
POS
POS
POS
POS
POS
POS
POS
POS
POS
*IBM PC/AT
compatible
computers
POS
POS
1024 X 768
NEG
NEG
YES*3
YES*3
YES*3
YES*3
YES*3
YES
NEG
NEG
POS
POS
POS
POS
NEG
NEG
– –
1152 X 864
1280 X 768
1360 X 765
1376 X 768
1280 X 1024
POS
POS
STILL
WIDE1
WIDE1
WIDE2
STILL
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
POS
POS
YES
YES
YES
POS
POS
NEG
POS
POS
POS
YES*4
YES*4
YES*4
YES
POS
POS
POS
POS
1600 X 1200
75.0
81.3
87.5
93.8
35.0
49.7
60.2
68.7
64.6
75.1
78.1
POS
POS
POS
POS
YES
YES
YES
YES
POS
POS
POS
POS
640 X 480
832 X 624
1024 X 768
1152 X 870
1280 X 1024
Sync on G
Sync on G
Sync on G
Sync on G
NEG
Sync on G
Sync on G
Sync on G
Sync on G
NEG
*Apple
– –
– –
– –
– –
– –
– –
YES
Macintosh*6
YES*3
YES
YES*4
YES*4
YES*4
Work Station
(EWS4800)
Work Station
(HP)
YES
YES
– –
YES
YES
– –
NEG
NEG
1280 X 1024
1152 X 900
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
– –
66.0
76.0
76.1
60.0
60.0
61.8
71.1
81.1
49.7
63.9
C Sync
C Sync
C Sync
– –
C Sync
C Sync
C Sync
– –
YES
YES
YES
YES
YES
YES
YES
– –
– –
– –
– –
– –
Work Station
(SUN)
– –
– –
– –
– –
– –
1280 X 1024
1024 X 768
1280 X 1024
YES*4
YES*3
YES*4
Work Station
(SGI)
IDC-3000G
PAL625P
– –
– –
768 X 576
640 X 480
50.0
59.9
31.4
31.5
NEG
NEG
NEG
NEG
YES
YES
YES
YES
YES*7
YES*7
YES*7
YES*7
– –
MOTION
– –
NTSC525P
52
Chapter 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
REFERENCE
*1 Only when using a graphic accelerator board that is capable of displaying 848 X 480.
*2 Aspect ratio is 5:4. This signal is converted to a 600 X 480 line signal.
*3 The picture is displayed in the original ersolution.
*4 The aspect ratiois 5:4. This signal is converted to a 900 dot X by 768 line signal.
*5 Normally the RGB SELECT mode is set automatically. If the pictuer is not displayed properly, set the mode for the input signals listed in the table.
*6 To connect the monitor to a Macintosh compute,ruse a D-sub 15-pin monitor adaptor with your computer’s video port. If your computer has a D-sub
15-pin connector, use an RGB cable.
*7 Other Screen modes are also available.
Notes:
•
•
•
•
•
When the input signals comply with the ersolution listed in the table above, the position and size of the pictuermay need to be adjusted.
When a 1280 X 1024 line signal or a 1600 dot X 1200 line signal is input, the picteurwill be compressed.
This monitor has a resolution of 1365 dot X 768 line. It isercommended that the input signal be XGA, wide XGA, or equivalent.
Some signals are not accepted with digital input.
The synch may be disturbed when a nonstandadr signal other than those previously mentioned is input.
•
If you are connecting a composite synch signal, use the HD temr inal.
* IBM is a registered trademark of International Business Machines Corporation of the United States.
* Macintosh is a registered trademark of Apple Computer, Inc. of the United States.
Chapter 7
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
REFERENCE
RCA Plasma Monitor
Limited Warranty
What your warranty covers:
•
Defects in materials or workmanship.
For how long after your purchase:
•
One year from date of purchase for labor.
•
One year from date of purchase for parts.
The warranty period for rental units begins with the first erntal or 45 days from date of shipment to the erntal firm,
whichever comes first.
What we will do:
Pay an Authorized Service Center the labor chagres to repair your unit.
Pay an Authorized Service Center for the new, or at our option,erfurbished replacement parts required to repair your unit.
How you get service:
•
•
•
Call 1-800-433-8974 and have your unit’s date of pucrhase and model/serial number ready.
A representative will troubleshoot your problem over the phone.
If the representative determines that you should receive service, they will provide you with the name(s) of the Authorized
Service Center in your area.
•
Contact the Service Center and arrange for home or pick up,erpair, and return service, provided that your unit is located
within the geographic territory covered by an Authorized Service Cente.r If not, you must take your unit to the Service
Center location at your own expense, or pay for the cost the Service Center may chgaer to transport your unit to and form
your home.
•
Proof of purchase in the form of a bill of sale or erceipted invoice which is evidence that the porduct is within the
warranty period must be presented to obtain warranty service. For erntal firms, proof of first rental is also required.
What your warranty does not cover:
•
Customer instruction. (Your Owner’s Manual describes how to install, adjust, and operate your unit. Any additional
information should be obtained from your dealer.)
•
•
•
•
•
•
•
•
Installation and related adjustments.
Damage resulting from non-approved installation methods.
Signal reception problems not caused by your unit.
Damage from misuse or neglect.
Batteries.
A television that has been modified or incorporated into other porducts.
A unit purchased or serviced outside the U.S.A.
Acts of nature, such as but not limited to lightning damage.
Product Registration:
•
Please complete and mail the Product Registration Card packed with your unit. It will make it easier to contact you
should it ever be necessary. The erturn of the card is not required for warranty coverage.
54
Chapter 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
REFERENCE
Limitation of Warranty:
•
THE WARRANTY STATED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PRODUCT. ALL OTHER
WARRANTIES, EXPRESS OR IMPLED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE) ARE HEREBY DISCLAIMED. NO VERBAL OR WRITTEN INFORMATION
GIVEN BY THOMSON MULTIMEDIA INC., ITS AGENTS OR EMPLOYEES SHALL CREATE A GUARANTY OR IN ANY
WAY INCREASE THE SCOPE OF THIS WARRANTY.
•
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER. THOMSON MULTIMEDIA INC. SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS
OR IMPLIED WARRANTY ON THIS PRODUCT. THIS DISCLAIMER OF WARRANTIES AND LIMITED WARRANTY
ARE GOVERNED BY THE LAWS OF THE STATE OF INDIANA. EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE
ON THIS PRODUCT IS LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE.
How State Law relates to warranty:
•
Some states do not allow the exclusion nor limitation of incidental or consequential damages, or limitations on how long
an implied warranty lasts, so the above limitations or exclusions may not apply to you.
•
This warranty gives you specific legal rights, and you also may have other rights that varyofmr state to state.
If you purchased your unit outside the United States:
•
This warranty does not apply. Contact your dealer for warranty infomration.
Service calls which do not involve defective materials or workmanship are not covered by this warranty. Costs
of such service calls are the sole responsibility of the purchaser.
Chapter 7
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Accessories
The accessories listed below are available from your Cinema Screen Dealer. See your dealer for prices.
Attachable Speakers – SPK50
Monitor Stand – PLB50
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Symbols
G
N
1080A 39
1080B 39
Gain 27
Navigating the menus 23
Noise Reduction 28
Number buttons 14
Go back button 13
Gray level 34
Guide button 13
A
Antenna button 13
Arrow buttons 13
Audio input 38
Audio menu 29, 50
Automatic Code Search 16
Auto picture 31
O
H
OK button 14
HD select 40
HD RCVR button 14
HD Receiver
Connecting 9
HD receiver 9
HD Receiver Mode 40
1080A 40
On•Off button 14
On-screen Menus 23
Display position 32
Options menu 38, 51
Orbiter 36
Autotuning 43, 51
Aux button 13
P
B
1080B 40
Personal computer
connecting 10, 11, 47
Picture-in-picture 23
Picture Quality menu 25, 50
Picture mode
Bright 25
Memory 25
Normal 25
Preset 25
Balance 29
Bass 29
Batteries 9, 15
Bias 27
BNC select 38
Black level 26
I
Info button 13
Input button 13
Input • Go Back 7
Inserting batteries in the remote 15
Installation 46
C
Floor Stand 46
CH+/CH- button 13
Cinema button 13
Clear button 13
CMPNT button 13
Color system 41
Components
Connecting 11
Computers
Connecting 11, 47
Contrast 26
Speakers 46
Ventilation requirements 46
Inverse 36
Soft 25
Picture position 31, 32
PIP 23
PLE 34
Polarities of Input Signals 41
Power 22
J
Jacks 8, 11
AC IN 8
External Speakers 8, 55
External Control 8
Video in/Audio in 8
Power cord 6
Power Saver 33
Power/standby indicator 33
Programming the remote 15
Presets 25
Control Lock 8
L
D
R
Language for the Menus 42
Laser Disc Player 10
Default values
Reducing noise in the picture 28
Remote Control
Automatic Code Search 16
Buttons 13,14
resetting 37, 50
DVD button 13
DVD Player 10, 11
M
Codes 18
inserting batteries 15
Mute 22
Navigating the Menus 23
Programmable Codes 18
Programming the Remote 16
Resetting to default values 37
Resolution of Input Signals 41
RGB Select 39
Macintosh computer
connecting 47
Memory Mode 25
Menu button 14
Menu • OK 7
E
External control 8
External Speakers 12, 55
Menu display
position 32
F
Film mode 34
Frequencies of Input Signals 41
Function menu 32, 50
Menu System 23, 50
Mini D-sub 15 Pin VGA
Signal Composition 47
Mode of Input Signals 41
Monitor button 14
Multi-screen 23
Mute 22
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
S
Safety information 1, 2
Safety metal fitting 6
Screen Saver 35, 50
Screen menu 30, 50
Screen size
Fill 30
Full 30
Normal 30
Stadium 30
Setting the Color Temperature 27
Setup menu 41, 51
Sharpness 26
Sleep button 14
Sleep timer
Cancelling 44
Checking 44
Setting 44
Speakers 12, 55
Specifications 48
Stand
using with Cinema Screen diaplay 55
T
TREBLE 29
Troubleshooting 49
V
VCR 10
VCR1 button 14
VCR2 button 14
Ventilation Requirements 46
Video button 14
Video 39
Viewing size
selecting 30
Volume 14, 22
Vol+/- buttons 14, 22
W
Warranty 54
Wide 39
Z
Zoom 7, 14
Zoom in/Zoom out buttons 14
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Please do not send any products to the address listed in this manual or on the carton. This will only add delays in service for your product.
ThomsonmultimediaInc.
10330 N. Meridian St.
Indianapolis, IN 46290
©2001 Thomson multimedia Inc.
Trademark(s) ® Registered
Marca(s) Registrada(s)
Printed in USA
TOCOM 15739310
Download from Www.Somanuals.com. All Manuals Search And Download.
|