QSC(LP)-100
Four Channel Low Profile RS-232
Asynchronous Communications Adapter
for PCI bus
User's Manual
QUATECH, INC.
5675 Hudson Industrial Parkway
Hudson, Ohio 44236
TEL: (330) 655-9000
FAX: (330) 655-9010
Download from Www.Somanuals.com. All Manuals Search And Download.
2006, Quatech, Inc.
NOTICE
The information contained in this document cannot be reproduced in any
form without the written consent of Quatech, Inc. Likewise, any software
programs that might accompany this document can be used only in accordance
with any license agreement(s) between the purchaser andQuatech, Inc. Quatech,
Inc. reserves the right to change this documentation or the product to which it
refers at any time and without notice.
The authors have taken due care in the preparation of this document and
every attempt has been made to ensure its accuracy and completeness. In no event
will Quatech, Inc. be liable for damages of any kind, incidental or consequential,
in regard to or arising out of the performance or form of the materials presented in
this document or any software programs that might accompany this document.
Quatech, Inc. encourages feedback about this document. Please send any
written comments to the Technical Support department at the address listed on the
cover page of this document.
DOS, Windows 95/98/2000/ME, Windows NT are trademarks or registered trademarks of
Microsoft Corporation. OS/2 is a registered trademark of IBM Corporation. All other trademarks
or registered trademarks are property of their respective owners.
iii
QSC(LP)-100 User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
Manufacturer's Name:
Quatech Inc.
Manufacturer's Address:
5675 Hudson Industrial Parkway
Hudson, Ohio 44236 (USA)
Application of Council Directive:
89/336/EEC
Standards to which
Conformity is Declared:
* EN50081-1 (EN55022,
EN60555-2, EN60555-3)
* EN50082-1 (IEC 801-2,
IEC 801-3, & IEC 801-4)
Type of Equipment:
Equipment Class:
Product Name:
Information Technology
Equipment
Commercial, Residential, & Light
Industrial
PCI Quad Serial Communications
Card
Model Number :
QSC(LP)-100
iv
QSC(LP)-100 User's Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1 General Information
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2 Hardware Configuration
. . . . . . . . . . . . . . . . . . . . . . . . . 8
. . . . . . . . . . . . . . . . . . . . . . . 8
2.1 Factory Default Configuration
2.2 Enable Scratchpad Register (SPAD, J2)
. . . . . . . . . . . . . . 8
2.3 Force High-Speed UART Clock (X2, X4, or X8,
J3-J5)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3 Hardware Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4 Address Map and Special Registers
. . . . . . . . . . . 12
. . . . . . . . . . . . . 12
4.1 Base Address and Interrupt Level (IRQ)
4.2 Enabling the Special Registers
. . . . . . . . . . . . . . . . . . . . . . 13
4.3 Interrupt Status Register
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.4 Options Register
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4.4.1 Enhanced Serial Adapter Identification
. . . . . . . . . . . 14
4.4.2 Clock Rate Multiplier
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5 Windows Configurations
. . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1 Windows Millennium
5.2 Windows 2000
5.3 Windows 98
5.4 Windows 95
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.5 Using the "New Hardware Found" Wizard
5.6 Viewing Resources with Device Manager
. . . . . . . . . . 19
. . . . . . . . . . . . 21
5.6.1 Changing Resource Settings with Device Manager
. 24
6 Other Operating Systems
. . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.1 Windows NT
6.2 OS/2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
6.3 DOS and other operating systems
. . . . . . . . . . . . . . . . . . . 30
6.3.1 QTPCI.EXE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
7 External Connections
8 PCI Resource Map
9 Specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
10 Troubleshooting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
QSC(LP)-100 User's Manual
v
Download from Www.Somanuals.com. All Manuals Search And Download.
1 General Information
The Quatech, Inc. QSC(LP)-100 provides four RS-232 asynchronous serial
communication interfaces for Low Profile IBM-compatible personal computer
systems using the PCI expansion bus. The QSC(LP)-100 uses Quatech's new
Enhanced Serial Adapter design. Legacy serial port data rates are limited to a
maximum of 115,200 bits per second. Quatech Enhanced Serial Adapters can
achieve data rates as high as 921,600 bits per second.
As a PCI device, the QSC(LP)-100 requires no hardware configuration.
The card is automatically configured by the computer's BIOS or operating system.
The four serial ports share a single interrupt line and are addressed in a
contiguous block of 32 bytes. A special interrupt status register is provided to
help software to manage the shared interrupt.
The QSC(LP)-100's serial ports are implemented using 16550 Universal
Asynchronous Receiver/Transmitters (UARTs). These UARTs contain hardware
buffers (FIFOs) which reduce processing overhead and allow higher data rates to
be achieved.
The QSC(LP)-100 is supported under several popular operating systems
and environments. Contact the sales department for details on current software
offerings. Most device drivers are available for download from the Quatech world
QSC(LP)-100 User's Manual
6
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Hardware Configuration
The QSC(LP)-100 is automatically configured at boot time by the
computer's BIOS or operating system. There are no required switches or jumpers
to set for installation.
This chapter lists a number of optional jumper settings that control various
hardware features. Jumpers J2-J5 are grouped together at the end of the board
opposite the HD-44 connector. Any changes from the factory default should be
made before installing the QSC(LP)-100 in the computer.
2.1 Factory Default Configuration
Figure 2 shows the jumper configuration as shipped from the factory, with
two spare jumpers applied in neutral positions. Remove one or both and apply as
shown in following sections to set optional features.
SPAD
X8
J2
J3
J4
X4
X2
J5
Figure 2 --- Factory default jumper configuration
2.2 Enable Scratchpad Register (SPAD, J2)
In the default configuration, an Interrupt Status Register (see section 4.3)
and an Options Register (see section 4.4) replace the scratchpad (base address + 7)
of each UART. If the SPAD jumper is applied as in Figure 3, the UART
scratchpad registers are enabled, and the Interrupt Status Register and the Options
Register are not available.
SPAD
X8
J2
J3
J4
J5
X4
X2
Figure 3 --- Enable scratchpad registers
QSC(LP)-100 User's Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Force High-Speed UART Clock (X2, X4, or X8, J3-J5)
These jumpers force an increase of the UART input clock frequency by a
factor of two, four, or eight. This feature can allow legacy software to use baud
rates above 115,200 bits per second. It is also useful if the serial port device
driver does not directly support setting the higher baud rates through the Options
Register (see section 4.4).
If one of these jumpers is applied, it overrides any value written to the
Options Register to set the clock multiplier by software. The effective baud rate
will be either two, four, or eight times the value for which the UART itself is
programmed.
The factory default is none of these jumpers applied, which allows for
software control of the clock multiplier via the Options Register. The Options
Register powerup default is for a standard times-1 clock of 1.8432 MHz for
compatibility with standard serial ports.
SPAD
X8
J2
J3
J4
J2
J3
J4
SPAD
X8
X4
X4
X2
X2
J5
J5
Force times-two clock
Baud rates up to 230.4 kbps
Factory default
software control
J2
J3
J4
J2
SPAD
SPAD
X8
X4
X2
X8
X4
X2
J3
J4
J5
J5
Force times-eight clock
Force times-four clock
Baud rates up to 460.8 kbps
Baud rates up to 921.6 kbps
Figure 4 --- Clock multiplier jumper options
QSC(LP)-100 User's Manual
8
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Hardware Installation
1. Turn off the power of the computer system in which the QSC(LP)-100 is
to be installed.
2. Remove the system cover according to the instructions provided by the
computer manufacturer.
3. Make any desired optional jumper setting changes.
4. Install the QSC(LP)-100 in any empty PCI expansion slot. The board
should be secured by installing the Option Retaining Bracket (ORB)
screw.
5. Replace the system cover according to the instructions provided by the
computer manufacturer.
6. Attach and secure the cable connectors to the desired equipment.
7. Turn on the power of the computer system.
The output of the QSC(LP)-100 is a 44-pin D-connector. A cable is
provided to convert the D-44 into four standard male D-9 connectors with all
control signals provided to each port (RTS, DTR, CTS, DSR, DCD, and RI).
Clock multiplier/
scratchpad select
SPAD
X8
X4
X2
Figure 5 --- Jumper/connector locations
QSC(LP)-100 User's Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Address Map and Special Registers
This chapter explains how the four UARTs and special registers are
addressed, as well as the layout of those registers. This material will be of interest
to programmers writing driver software for the QSC(LP)-100.
4.1 Base Address and Interrupt Level (IRQ)
The base address and IRQ used by the QSC(LP)-100 are determined by the
BIOS or operating system. Each serial port uses 8 consecutive I/O locations. The
four ports reside in a single block of I/O space in eight byte increments, for a total
of 32 contiguous bytes, as shown in Figure 6.
Port
I/O Address Range
Serial 1
Serial 2
Serial 3
Serial 4
Base Address + 0
Base Address + 8
to Base Address + 7
to Base Address + 15
Base Address + 16 to Base Address + 23
Base Address + 24 to Base Address + 31
Figure 6 --- Port Address Map
All four serial ports share the same IRQ. The QSC(LP)-100 signals a
hardware interrupt when any port requires service. The interrupt signal is
maintained until no port requires service. Interrupts are level-sensitive on the PCI
bus.
The base address and IRQ are automatically detected by the device drivers
Quatech supplies for various operating systems. For cases where no device driver
is available, such as for operation under DOS, Quatech supplies the "QTPCI"
DOS software utility for manually determining the resources used. Seesection
6.3.1 for details.
QSC(LP)-100 User's Manual
10
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2 Enabling the Special Registers
The QSC(LP)-100 contains two unique registers, an Interrupt Status
Register and an Options Register. These registers are enabled when the SPAD
jumper (J6) is removed (factory default). They replace theUART Scratchpad
Register on accesses to register address 7.
The Interrupt Status Register and Options Register are accessed through
the scratchpad location of any UART. The DLAB bit of the UART (Line Control
Register, bit 7) is used to select between the two registers. The most recent write
of a DLAB bit in any UART selects between the two registers as shown in Figure
7.
Register selected for
DLAB Bit SPAD Jumper
address 7 accesses
0
1
X
removed
removed
applied
Interrupt Status Register
Options Register
Scratchpad Registers
Figure 7 --- DLAB bit selects between special registers
4.3 Interrupt Status Register
The read-only Interrupt Status Register can be used to quickly identify
which serial ports require servicing after an interrupt. Reading the Interrupt Status
Register will return the interrupt status of the entire QSC(LP)-100, as shown in
Figure 8. The individual bits are cleared as the interrupting ports are serviced.
The interrupt service routine should ensure that the interrupt status register reads
zero before exiting.
Bit
Description
0 (not used)
7 (MSB)
6
5
4
3
2
1
0
0 (not used)
0 (not used)
0 (not used)
Port 4 --- 1 if interrupt pending
Port 3 --- 1 if interrupt pending
Port 2 --- 1 if interrupt pending
Port 1 --- 1 if interrupt pending
Figure 8 --- Interrupt Status Register
QSC(LP)-100 User's Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
4.4 Options Register
The Options Register allows software to identify the QSC(LP)-100 as a
Quatech Enhanced Serial Adapter. It also allows software to set the UART clock
rate multiplier. Figure 9 shows the structure of the Options Register.
The powerup default of the Options Register is all bits zero.
Bit
Name
Description
ID bit 1
7 (MSB)
ID1
6
5
4
3
2
1
0
ID0
ID bit 0
-
(reserved, 0)
-
-
(reserved, 0)
(reserved, 0)
-
(reserved, 0)
RR1
RR0
Clock rate multiplier bit 1
Clock rate multiplier bit 0
Figure 9--- Options Register bit definitions
4.4.1 Enhanced Serial Adapter Identification
The ID bits are used to identify the QSC(LP)-100 as a Quatech Enhanced
Serial Adapter. Logic operations are performed such that the values read back
from these bits will not necessarily be the values that were written to them. Bit
ID1 will return the logical-AND of the values written to ID[1:0], while bit ID0
will return their exclusive-OR.
Software can thus identify a Quatech Enhanced Serial Adapter by writing
the ID bits with the patterns shown in the "write" column of Figure 10, then
reading the bits and comparing the result with the patterns in the "read" column.
Matching read patterns verify the presence of the Options Register.
Write
Read
ID1 ID0 ID1 ID0
0
0
1
1
0
1
0
1
0
0
0
1
0
1
1
0
Figure 10 --- ID bit write/read table
QSC(LP)-100 User's Manual
12
Download from Www.Somanuals.com. All Manuals Search And Download.
4.4.2 Clock Rate Multiplier
A standard RS-232 serial port operates at a clock speed of 1.8432 MHz.
In order to achieve higher data rates, Quatech Enhanced Serial Adapters can
operate at two times, four times or even eight times this standard clock speed.
This is controlled by the clock rate multiplier bits in the Options Register.
Software can determine the UART clock frequency by reading the clock
rate multiplier bits RR1 and RR0 in the Options Register as shown in Figure 11.
RR1 and RR0 can be set by writing to the Options Register if the X2, X4, and X8
jumpers (J3-J5) are all removed. If one of these jumpers is applied, the RR1 and
RR0 bits are forced to the appropriate value. Reading the Options Register will
always return the clock rate multiplier at which the board is operating.
Clock Rate
Multiplier
X1
(default)
X2
UART Clock
Frequency
Maximum Data
Rate
RR1 RR0
0
0
1.8432 MHz
115.2 kbaud
0
1
1
1
0
1
3.6864 MHz
7.3728 MHz
14.7456 MHz
230.4 kbaud
460.8 kbaud
921.6 kbaud
X4
X8
Figure 11 --- Rate Register bit definition
At powerup and reset, the Options Register is initialized to 0. The
QSC(LP)-100 will thus powerup in the x1 mode with software control of the
clock rate multiplier enabled as long as the X2, X4, and X8 jumpers are not
installed.
Software can control high baud rates through a combination of changing
the clock rate multiplier and the UART baud rate divisor. For example, a baud
rate of 230.4 kbps could be achieved by setting the clock rate multiplier to X2
mode (or by applying the X2 jumper) and setting a software application for 115.2
kbps.
QSC(LP)-100 User's Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Windows Configurations
5.1 Windows Millennium
1. After inserting the QSC(LP)- 100 for the first time the "Add New
Hardware Wizard" will begin. Select "Search for the best driver for your
device.". Check the "Removable media" and "Specify location" box.
Click the "Next" button.
2. Window will locate the proper INF file and copy the file from the CD.
Click the "Next" button.
3. The final dialog screen will verify the file copy from theCD.
Click the "Finish" button.
QSC(LP)-100 User's Manual
14
Download from Www.Somanuals.com. All Manuals Search And Download.
5.2 Windows 2000
1.
After inserting a QSC(LP)-100 for the first time, the "Add New
Hardware Wizard will appear at start up. Click the "OK" button.
2. The following dialog box will appear. Insert the Quatech COM CD
(shipped with the device). Click the "OK" button.
3.
4.
The following dialog box will display the appropriate INF file on the CD
in the drive. Click the "OK" button.
Window will copy the INF file from the CD and display a final dialog
indication that the process is complete. Click the "Finish" button.
QSC(LP)-100 User's Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3 Windows 98
1.
After inserting a QSC(LP)-100 for the first time, the "Add New
Hardware Wizard will appear at start up. Click the "Next" button.
2.
Select "Search for the best driver for your device".
Click the "Next" button.
3.
On the next dialog, select the "CD-ROM DRIVE" check box. Insert the
Quatech COM CD (shipped with the device) into the CD-ROM drive.
Click the "Next" button.
QSC(LP)-100 User's Manual
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4.
5.
The following dialog box will display the appropriate INF file on the
diskette in the drive. Click the "Next" button.
Window will copy the INF file from the diskette and display a final dialog
indication that the process is complete. Click the "Finish" button.
5.4 Windows 95
Windows 95 maintains a registry of all known hardware installed in your
computer. Inside this hardware registry Windows 95 keeps track of all of your
system resources, such as I/O locations, IRQ levels, and DMA channels. The
"Add New Hardware Wizard" utility in Windows 95 was designed to add new
hardware and update this registry.
An "INF" configuration file is included with the QSC(LP)-100 to allow
easy configuration in the Windows 95 environment.
5.5 Using the "New Hardware Found" Wizard
The following instructions provide step-by-step instructions on installing
the QSC(LP)-100 in Windows 95 using the "New Hardware Found" wizard.
1. After booting the computer with a newly-installed QSC(LP)-100, the
"New Hardware Found" dialog box will appear. If you have never
installed a Quatech PCI communications adapter before, the dialog box
may simply indicate that it has found a "PCI Card."
QSC(LP)-100 User's Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Select the radio button for "Driver from disk provided by hardware
manufacturer." Click the "OK" button to continue.
3. An "Install From Disk" dialog box should pop up. Insert the disk with the
Quatech INF files on it, select the correct drive letter, and click the "OK"
button. Windows 95 automatically browses the root directory for an INF
file that defines configurations for Multi-function Adapters. If no INF
files are found, click the "Browse" button and search the Win95 sub
directory on the installation disk. You are not required to select the file
name. After finding the directory containing the INF files, Windows 95
will choose the correct file.
4. The "New Hardware Found" dialog box will appear again, this time for an
"Unknown Device."
5. Again select the radio button for "Driver from disk provided by hardware
manufacturer." Click the "OK" button to continue.
6. Another "Install From Disk" dialog box will pop up. The path should
already be pointing to the Quatech disk. Click the "OK" button to
continue.
7. You should now see the "Copying Files" dialog box as Windows 95 copies
the driver files from the disk..
8. The installation utility will ask for your Windows 95 installation disks.
Serial communication ports require two drivers supplied by Microsoft to
function: SERIAL.VXD and SERIALUI.DLL. Insert the disk or CD and
click "OK".
NOTE:
You may be able to skip this step if you are certain that your system has the latest
version of these files installed. If you do not have your Windows 95 install disks
immediately available, click "OK" anyway. A dialog box appears with an option
to Skip the files. Click the Skip button and the files will not be installed. This is
all right if the latest version of these drivers are currently in the
\WINDOWS\SYSTEM directory.
9. The "New Hardware Found" dialog will repeat for each of the serial ports
on the QSC(LP)-100 as each port is registered with Windows 95.
10. Installation is complete.
5.6 Viewing Resources with Device Manager
QSC(LP)-100 User's Manual
18
Download from Www.Somanuals.com. All Manuals Search And Download.
The following instructions provide step-by-step instructions on viewing
resources used by the QSC(LP)-100 in Windows using the "Device Manager"
utility. Select Start|Help from within Windows for additional information on this
utility.
1. Double click the "System" icon inside the Control Panel folder. This
opens up the System Properties box.
2. Click the "Device Manager" tab located along the top of the System
Properties box. This lists all hardware devices registered inside the
Windows registry. Additional information is available on any of these
devices by click on the device name and then selecting the "Properties"
button.
3. Double click the device group "Multi-function Adapters". The
QSC(LP)-100 model name should appear in the list of Multi-function
adapters.
4. Double click the QSC(LP)-100 model name and a properties box should
open for the hardware adapter.
5. Click the "Resources" tab located along the top of the properties box to
view the resources Windows has allocated for the QSC(LP)-100 match
the hardware configuration. Because PCI is a true plug-and-play bus,
do not attempt to modify the configuration values listed. Click
"Cancel" to exit without making changes.
QSC(LP)-100 User's Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 12--- Windows Device Manager
6. The QSC(LP)-100 serial ports are also listed under the group Ports (COM
and LPT). Windows 95 does not assign COM1-COM4 to ports addressed
at nonstandard locations. The QSC(LP)-100 ports will be enumerated
starting with COM5 (or higher) even if lower logical numbers are
available.
7. Select any of the Quatech Serial Ports listed under the group Port (COM
and LPT) and click the "Properties" button. This action opens a properties
dialog for the specific COM port on the QSC(LP)-100.
8. Click the "Port Settings" tab and then click the "Advanced" button. The
QSC(LP)-100 driver will display a custom Advanced Port Settings control,
which allows the ports UART compatibility mode and FIFO threshold
levels to be configured. The threshold values of full-scale for the transmit
buffer and 3/4-scale for the receive buffer shown below are optimal for
most applications. Note that the FIFO option for each of the
QSC(LP)-100's two ports is configured independently.
QSC(LP)-100 User's Manual
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 13--- Windows Device Manager
9. Use the Logical COM Port names to access the serial ports on your
QSC(LP)-100 through your software applications. Note: The Logical
COM Port name is assigned to your ports by Windows . This name is
required by a Windows application when accessing a particular port.
QSC(LP)-100 User's Manual
21
Download from Www.Somanuals.com. All Manuals Search And Download.
5.6.1 Changing Resource Settings with Device Manager
1. Start the Windows 95/98/ME Device Manager.
2. Double click on the hardware class Multi-Port Serial Adapters to list
hardware devices in the class.
3. The QSC(LP)-100 “parent device” belongs to this hardware class. The
full device name for the QSC(LP)-100 is Quatech QSC(LP)-100:
Four-Port RS-232 Serial Adapter.
QSC(LP)-100 User's Manual
22
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Open the Properties dialog for the QSC(LP)-100 device, then click the
Resources tab to view the Input/Output Range and Interrupt Request
resource allocations. Do not change these settings without specific
instructions from a Quatech Technical Support Specialist. To exit
without saving changes, click the “cancel” button.
5. Open the Properties dialog for the QSC(LP)-100 device, then click the
Advanced tab to view the clock rate settings.
QSC(LP)-100 User's Manual
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Data Rate Multiplier
Clock Mode Max bps Description
Auto clock mode enables applications to
request any baud rate up to 921,600.
921,600 The hardware drivers will select the
correct clock multiplier based on the
baud rate requested
The X1 clock mode mimics a standard
COM port. The hardware drivers lock
115,200 the clock to the standard rate. The port
will run at the baud rate requested by
the application.
Auto
X1
The X2 clock mode locks the ports
hardware clock at double the standard
230,400 rate. The baud rate the port runs at will
always be double the rate requested by
the applications. This mode is useful
X2
QSC(LP)-100 User's Manual
24
Download from Www.Somanuals.com. All Manuals Search And Download.
for legacy applicattions which cannot
request baud rates over 115,200
The X4 clock mode locks the ports
hardware clock at four times the
standard rate. The baud rate the port
460,800 runs at will always be four times the rate
requested by the application. This mode
is useful for legacy applications which
cannot request baud rates over 115.200.
The X8 clock mode locks the ports
hardware clock at eight times the
X4
X8
standard rate. The baud rate the port
runs at will always be eight times the
rate requested by the application. This
921,600
mode is useful for legacy applications
which cannot request baud rates over
115.200.
6. Double click the hardware class Ports (Com and LPT). Each
Quatech PCI Serial Port listed in this class is a “child device” of the
QSC(LP)-100 “parent device.”
7. Open the Properties dialog for a COM port, then click the Port
Properties tab to view the settings for that port.
QSC(LP)-100 User's Manual
25
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Click the "Port Settings" tab and then click the "Advanced" button.
The QSC(LP)-100 driver will display a custom Advanced Port Settings
control, which allows the ports UART compatibility mode and FIFO
threshold levels to be configured. The threshold values of full-scale for
the transmit buffer and ¾-scale for the receive buffer are optimal for
most applications. Note that the FIFO option for each of the
QSC(LP)-100's four ports is configured independently.
QSC(LP)-100 User's Manual
26
Download from Www.Somanuals.com. All Manuals Search And Download.
QSC(LP)-100 User's Manual
27
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Other Operating Systems
Device drivers for Windows NT and OS/2 are also available for the
QSC(LP)-100. The board can be used under DOS and other operating systems as
well in many circumstances. The software described below can be downloaded
from the Quatech web site if it did not come with the board.
6.1 Windows NT
The Windows NT device driver is installed by running the SETUP
program. Up to 256 serial ports are supported. There is a command line-based
configuration utility which is used for adding PCI bus and ISA bus serial ports.
Please refer to the documentation included with the device driver for full
installation and configuration details.
6.2 OS/2
The OS/2 device driver supports up to 32 serial ports in a system.
Installation is a manual, but simple, process. Please refer to the documentation
included with the device driver for full installation and configuration details.
6.3 DOS and other operating systems
The QSC(LP)-100 is not a direct drop-in replacement for a legacy serial
port because its base address and IRQ cannot be fixed at values such as 3F8 hex,
IRQ 4 (COM1) or 2F8 hex, IRQ 3 (COM2), etc. Rather, the system BIOS assigns
the address and the IRQ in a plug-and-play fashion at boot time. Software which
is to use the QSC(LP)-100 must be able to accommodate any valid assignments of
these resources.
For Windows 95/98/2000/ME, Windows NT and OS/2, the Quatech
device drivers determine what the resource assignments are and proceed
accordingly. In other cases, however, the user must intervene. The discussion
below will center on DOS, but the concepts can be applied to other operating
systems as well.
Many DOS applications support user configuration of the base address and
IRQ of a serial port. Such applications can generally make use of the
QSC(LP)-100. Older applications, as well as some custom software, may use
hard-coded standard legacy serial port addresses. These applications will require
modifications if they are to use the QSC(LP)-100.
Custom applications for which the customer has source code can be
modified to make just a few PCI BIOS function calls to obtain all the necessary
configuration information. The PCI BIOS specification can be obtained from the
PCI Special Interest Group. Contact Quatech technical support for more
information.
QSC(LP)-100 User's Manual
28
Download from Www.Somanuals.com. All Manuals Search And Download.
6.3.1 QTPCI.EXE
Quatech's "QTPCI" utility supplies the information required when
modifying the serial port settings of the application. This program should be run
from real DOS, not in a Windows DOS box.
Figure 14 shows the Basic Mode display for the QSC(LP)-100 after the
"Q" key has been pressed. In this example, the QSC(LP)-100 uses I/O base
address FF80 hex and IRQ 11. The hardware revision of the QSC(LP)-100 is also
displayed. Pressing the "N" key will show similar information for all
non-Quatech PCI devices in the system, including those devices integrated on the
motherboard.
The QTPCI program is capable only of displaying the PCI configuration. It
cannot be used to make changes.
Figure 14 --- QTPCI.EXE Basic Mode display
QSC(LP)-100 User's Manual
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 15 shows the Expert Mode display for the QSC(LP)-100 after the
"Q" key has been pressed. The information from the Basic Mode display is
presented along with more details such as the Vendor and Device IDs, PCI Class
Code, size of memory and I/O regions, etc. Pressing the "N" key will show
similar information for all non-Quatech PCI devices in the system, including those
devices integrated on the motherboard. In this example, the "Base addr 0"
resource is reserved.
For users interested in even more details, PCI BIOS information can be
displayed by pressing the "B" key. Pressing the "I" key displays thePCI interrupt
routing table.
Figure 15 --- QTPCI.EXE Expert Mode display
QSC(LP)-100 User's Manual
30
Download from Www.Somanuals.com. All Manuals Search And Download.
7 External Connections
RS-232-C devices are classified by their function as either Data Terminal
Equipment (DTE) or Data Communication Equipment (DCE). Generally, data
terminal equipment is defined as the communication source and data
communication equipment is defined as the device that provides a communication
channel between two DTE-type devices.
Terminal
DTE
Modem
DCE
RS-232-C
RS-232-C
Telephone
line
Terminal
DTE
Modem
DCE
Figure 16 --- Use of DTEs and DCEs in a communications link
DTE- and DCE-type devices have complementary pinouts to allow
terminals and modems to be connected directly using a one-to-one cable as shown
in Figure 16. In many applications, DCEs are unnecessary, and in these cases a
cable called a "null modem cable" or "modem eliminator cable" is used to directly
connect two DTE-type devices. A typical null modem cable is also shown in
Figure 17.
(3)
(2)
(4)
(5)
(20)
(6)
(8)
(22)
(7)
(3)
(2)
(4)
(5)
(20)
(6)
(8)
(22) RI
(7)
RxD
TxD
RTS
CTS
DTR
DSR
DCD
RI
(3)
(2)
(4)
(5)
(20)
(6)
(8)
(22)
(7)
RxD
TxD
(3)
(2)
(4)
(5)
(20)
(6)
(8)
(22)
(7)
RxD
TxD
RTS
CTS
DTR
DSR
DCD
RI
TxD
RxD
CTS
RTS
DSR
DTR
DCD
RI
RTS
CTS
DTR
DSR
DCD
GND
GND
GND
GND
Typical DTE-to-DCE cable
Typical DTE-to-DTE null modem cable
Figure 17 --- Cabling requirements for RS-232-C devices
(cables using 25-pin connectors shown)
QSC(LP)-100 User's Manual
31
Download from Www.Somanuals.com. All Manuals Search And Download.
The QSC(LP)-100 is a DTE device which connects to peripheral
equipment through a single female D-44 connector, or using the adapter cable,
four male D-9 connectors. The standard serial port connections are listed in
Figure 18.
Port 1
Port 2
Port 3
Port 4
RS-232
Signal
D-44 D-9 D-44 D-9 D-44 D-9 D-44 D-9
TxD
RxD
RTS
CTS
DTR
DSR
DCD
RI
13
42
14
43
28
27
44
29
19
3
2
7
8
4
6
1
9
5
10
39
11
40
24
23
41
25
8
3
2
7
8
4
6
1
9
5
6
3
2
7
8
4
6
1
9
5
2
3
2
7
8
4
6
1
9
5
35
7
31
3
36
21
20
37
22
26
32
17
16
33
18
30
GND
Figure 18 --- QSC(LP)-100 connector pinouts
QSC(LP)-100 User's Manual
32
Download from Www.Somanuals.com. All Manuals Search And Download.
8 PCI Resource Map
Listed below are the PCI resources used by the QSC(LP)-100. Such
information may be of use to customers writing their own device drivers or other
custom software. A detailed description of the QSC(LP)-100's UARTs is
available on the Quatech web site.
(all numbers in hex)
PCI Vendor ID:
PCI Device ID:
0x135C
0x0170
Quatech, Inc.
QSC(LP)-100
PCI Class Code
Base class:
Subclass:
0x07
0x02
0x00
Simple communications controller
Multiport serial controller
Interface:
IRQ sourced by:
Base address 0:
Base address 1:
Base address 2:
INTA#
0x80 bytes Memory Reserved region
0x80 bytes I/O
0x20 bytes I/O
Reserved region
Serial ports:
Port 1 at offset 0x00
Port 2 at offset 0x08
Port 3 at offset 0x10
Port 4 at offset 0x18
QSC(LP)-100 User's Manual
33
Download from Www.Somanuals.com. All Manuals Search And Download.
9 Specifications
Bus interface:
PCI, 32-bit bus, Universal Voltage Signaling
IBM-compatible computers
Dimensions:
approx. 5.0" x 3.7"
Serial ports
Controller:
16550 with 16-byte FIFOs
Interface:
One female D-44 connector
Four male D-9 connectors
using adapter cable
Transceivers:
ICL3245CA
High-level output:
Low-level output:
Switching speed
+5V min
-5V max,
Power requirements
Temperature:
Humidity:
+5.0 volts: approx. 250 mA
operating 0° to 70°
storage -50° to 80°
10% to 90%
QSC(LP)-100 User's Manual
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Maximum Load (pF)
Data Rate
(kbaud)
4%
trans
time
N/A
100
330
800
10%
trans
time
100
430
900
15%
trans
time
300
670
1100
3300
20%
trans
time
430
900
1630
4300
25%
trans
time
470
1100
2000
4800
921.6
460.8
230.4
115.2
1570
Note 1: The signal transition time ratio is defined as the percentage of the
unit interval or bit time (the inverse of the data rate) that is occupied by the
signal transitioning from -3V to +3V. The EIA/TIA-232-E standard
defines a maximum signal transition time ratio of 4%; most RS-232
receivers will recognize signal transitions with much larger ratios. With a
4% signal transition time ratio, EIA/TIA-232-E is limited to a theoretical
data rate of 200 kbaud. If maximum signal transition time ratio is
extended to 10%, 15%, 20%, or even 25%, the maximum data rate
achievable using EIA/TIA-232-E can be increased past 200 kbaud.
Note 2: A typical value for capacitance per foot of standard cable is 50
pF/ft.
QSC(LP)-100 User's Manual
35
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Troubleshooting
Listed here are some common problems and frequent causes of those
problems. If the information here does not provide a solution, contact Quatech
technical support.
Any unauthorized repairs or modifications will void the QSC(LP)-100's warranty.
Computer will not boot up.
1. Is the QSC(LP)-100 properly inserted? Remove the card and try again.
Perhaps try a different expansion slot.
2. Ensure that an ISA-bus card is not using the same IRQ that the PCI BIOS
tries to assign to the QSC(LP)-100. Most computers have BIOS setup
options to reserve IRQs for either ISA or PCI use. Try reserving the IRQ
for the ISA card. The BIOS will automatically choose a different IRQ for
the QSC(LP)-100. An address conflict is unlikely because most PCI-based
computers will assign I/O addresses in such a way that they cannot conflict
with ISA-bus devices.
3. The QSC(LP)-100 may be defective. Contact technical support for
instructions.
Cannot communicate with other equipment.
1. Are the cable connections correct? Are the cables securely attached?
2. Is the software configured with the correct base address and IRQ
information for the QSC(LP)-100? (This is mainly a DOS issue.)
3. Is the device driver installed?
4. If you are trying to communicate with another DTE, a null-modem cable
will be required.
5. If possible, use a loopback connector to test the port. This connector
needs to connect the following sets of signals on a D-9 connector:
TxD and RxD (pins 2 and 3)
RTS and CTS (pins 7 and 8)
DCD, DTR, DSR, and RI (pins 1, 4, 6 and 9)
QSC(LP)-100 User's Manual
36
Download from Www.Somanuals.com. All Manuals Search And Download.
QSC(LP)-100
User's Manual
Revision 1.12
November 2006
P/N: 940-0180-112
QSC(LP)-100 User's Manual
i
Download from Www.Somanuals.com. All Manuals Search And Download.
|