Samsung Security Camera SPD 2700 User Guide

37X/33X/27X Ultra-Low Light SPEED DOME CAMERA

SPD-3700T/3700/3310/2700 User’s Manual

Before installing and operating the camera, please read this user’s manual carefully.

English

Download from Www.Somanuals.com. All Manuals Search And Download.

The lightning flash with an arrowhead symbol, within an equilateral triangle is

intended to alert the user to the presence of uninsulated “dangerous voltage”

within the product's enclosure that may be of sufficient magnitude to constitute

a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user

to the presence of important operating and maintenance (servicing) instructions

in the literature accompanying the appliance.

INFORMATION-This equipment has been tested and found to comply with

limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference

at his own expense.

WARNING

- CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE

MANUFACTURER COULD VOID THE USER'S AUTHORITY TO OPERATE

THE EQUIPMENT.

- TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS PRODUCT TO RAIN OR MOISTURE.

CAUTION : To prevent electric shock and risk of fire hazards:

- The installation for this apparatus should be by a qualified service person

and should conform to all local codes.

- Do NOT use power sources other than Class 2 power source.

- Carefully push the unlock buttons to prevent injury due to falling of this

apparatus.

This installation should be made by a qualified service person and

should conform to all local codes.

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

■

Sequence Setting …………………………………………………………48

•

Features ………………………………………………………………………… 6

Cautions for Using Auto Track (SPD-3700T) ………………………… 7

Warnings & Cautions ……………………………………………………… 9

Components and Accessories …………………………………………… 12

Component Names and Functions……………………………………… 13

Installing Your Camera……………………………………………………… 15

▶

Power On Resume & MD Dwell Time ………………………………………… 48

Preset ………………………………………………………………………………… 49

Swing SEQ …………………………………………………………………………… 53

Group SEQ …………………………………………………………………………… 54

Tour SEQ ……………………………………………………………………………… 55

PTZ Trace …………………………………………………………………………… 56

Auto Run……………………………………………………………………………… 57

■

Speed Dome Camara and Appliances Wiring Diagram ……… 15

Communication DIP Switch Settings (SW2)……………………… 17

P/T Setting ………………………………………………………………… 58

▶

Pan/Tilt Limit ………………………………………………………………………… 58

Area Setting ………………………………………………………………………… 59

Area Masking ……………………………………………………………………… 60

Prop. P/T ……………………………………………………………………………… 61

Digital Flip …………………………………………………………………………… 62

Image Hold…………………………………………………………………………… 63

Auto Track1 ………………………………………………………………………… 64

Auto Track2 ………………………………………………………………………… 66

▶

Protocol Settings …………………………………………………………………… 17

Baud Rate Settings………………………………………………………………… 18

Communication Method Settings ……………………………………………… 18

Communication Response Settings …………………………………………… 18

Termination Settings ……………………………………………………………… 18

Camera Backup Settings ………………………………………………………… 19

■

Camera ID DIP Switch Settings (SW1) …………………………… 19

Camera ID Chart …………………………………………………………………… 20

On-Ceiling Mount Type Installation Example …………………… 29

▶

•

OSD Setting …………………………………………………………………… 68

Alarm Setting ………………………………………………………………… 69

Initialization Setting…………………………………………………………73

Status Check…………………………………………………………………… 75

Product Specifications……………………………………………………… 76

•

Interface Symbols …………………………………………………………… 32

Operating Your Camera …………………………………………………… 33

Functional Description……………………………………………………… 37

■

Camera Setting …………………………………………………………… 37

▶

Focus and Zoom …………………………………………………………………… 37

White Balance ……………………………………………………………………… 39

Exposure……………………………………………………………………………… 40

Backlight……………………………………………………………………………… 41

AGC …………………………………………………………………………………… 44

SSNR(Samsung Super Noise Reduction) …………………………………… 45

Day & Night ………………………………………………………………………… 46

Others ………………………………………………………………………………… 47

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Cautions for Using Auto Track (SPD-3700T)

Features

The following cautions are for the Auto Track function built-in with the SPD-3700T;The SPD-

3700/3310/2700 do not have Auto Track.

A/F 37x/33x/27x Optical Zoom

Smart P/T

To use Auto Track to its full potential, please read and be aware of the following cautions.

Neglecting the cautions may cause unsatisfactory performance of the tracking function as

well as camera malfunctions.

The built-in 37x(SPD-3700T/37-0)/33x(SPD-3310)/27x

(SPD-2700) optical zoom lens with auto-focus is combined

with a 12x digital zoom, providing a maximum of 444x/

396x/324x zoom.

The Smart P/T function automatically adjusts the

control speed of the Pan and Tilt functions according to

the current zoom power. It is useful to adjust the

functions manually for detailed controls when

monitoring a high-powered zoom.

• Auto Track is specifically to track down unknown intruders. It is not be suitable to monitor

a crowd.

• If the camera is not safely secured, tracking errors may occur.

• If the camera lens is smeared with foreign substances, snow flakes, or raindrops, the

camera may incur unsatisfactory performance in the tracking function. For optimal

performance, please install the camera in an environment safe from contamination, and

clean the camera lens on regular basis.

• If the tracking function shows poor performance at nighttime or under low light

circumstances, use the Sens-Up function.

Versatile Protocol Processing

Day & Night

This camera supports a total of 8 types of communication

protocols: Samsung Techwin, Pelco-D, Pelco-P, Samsung

Electronics, Panasonic, Honeywell, AD and Vicon.

With its daytime & nighttime switch and Sens-Up

functions based on the ICR (Infrared Cut filter Removal)

method, the camera provides high quality pictures

regardless of whether it is day or night.

* Sens-Up increases the CCD sensitivity by electrically

extending the camera’s exposure time.

Wide Range Auto Security

Functions

- Auto Tracking(SPD-3700T Only) : A moving object or a

person can be tracked and recorded automatically by

the camera with its Pan, Tilt, and Zoom functions.

- Multiple Preset Function Saving : Up to 13 camera

image properities can be saved individually to provide

high quality pictures.

- Image Holding : When moving between presets in Group

and Tour functions, using this Preset Freeze function

holds the image status and helps the screen observer

relieve visual fatigue.

- PIZ Trace : Patterns operated with the joystick can be

saved and replayed by users.

- Swing : Using the Swing function commands the

camera to move between 2 selected locations,

monitoring the route.

* Day & Night enables you to select between color and

B/W modes depending on the lighting conditions.

• Auto Track may have errors at times when pronounced shadows are created: e.g. sunrise

and sunset.

OSD (On Screen Display)

• The camera may catch and follow unintended movements – car traffic or swaying tree

branches – during the Auto Track operation.To prevent and correct such errors, adjust the

installation direction and angle of the camera, or use Zone Settings (Mask) (page 67).

• Adjust the installation direction and angle of the camera, or use Zone Settings also under

the following conditions:With excessively bright light sources, under flickering lights, or if

the camera displays internal reflections.

• When using Auto Track, it is recommended to adjust the tracking object size to 1/4 of the

screen.

• This feature may not perform as expected depending on the situation and circumstances.

Samsung Techwin is not responsible for injuries and financial damage caused by the

situation described above.

The camera IDs, camera preset numbers, preset names,

area names, and camera operation status are displayed

on the monitor, allowing set up of various camera

functions through the OSD menu screen.

Preset Position Saving and Loading

Up to 255 preset positions can be set. Using this

function saves and brings up the camera feed of a

selected monitoring location.

- Group Search : Maximum 255 Preset positions are

toured in order.

- Tour Search : Maximum 6 Group Search functions are

toured in order.

Camera Backup

Digital Flip

This is to back up the camera’s sequence information

and presets. This is useful when the camera or its

install base are damaged or malfunctions occur.

The Digital Flip function is useful to monitor moving

objects or people passing directly under the camera.

When an object or a person passes directly under the

camera, its tilt monitor follows the object or person over

100 degrees to the other side of the tilt area without

panning. The screen inversion starting to occur at 100

degrees or higher is digitally adjusted.

Area Masking

If a monitoring location includes a highly private area,

the area can be selectively masked on the screen.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Samsung Techwin cares for the environment at all product manufacturing

stages to preserve the environment, and is taking a number of steps to provide

customers with more environment-friendly products. The Eco mark represents

Samsung Techwin's will to create environment-friendly products, and indicates

that the product satisfies the EU RoHS Directive.

Warnings & Cautions

Warnings

Stop using the camera if smoke or

abnormal heat is detected.

Do not install on your own.

Warnings & Cautions

This information is provided to ensure your safety and to prevent any losses, financial or

otherwise. Please read it carefully and use the product accordingly.

* For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as

an aerial ladder while providing after-sales service shall be at your expense.

* Unplug the power plug when thunder crashes or lightning flashes to prevent fire and damage to the product.

This installation should be made by a qualified service

person. Installing this product on your own may result in

fire or electric shock. For the installation service, contact

the retail shop where you bought the product.

May cause fire.

* This product is support equipment for a security system. Therefore, we can't compensate for material losses and/or

personal injuries by robbery, fire, natural disaster, or anything of the sort.

Warning/Caution/Special Mark Messages

Do not install in high humidity or in a

place that may be exposed to oil or gas.

Do not install on an unsubstantial wall

that may be subject to vibrations.

Ignoring this information may

result in material loss and/or

result in material loss and/or slight

serious personal injuries, including

injuries.

death.

Indicates “Prohibited”.

Indicates “No Disassembly”.

May cause product malfunctions, electric shocks, and fire.

May cause the product to fall.

Do not handle the power plug

with wet hands.

Do not disassemble the camera or

insert foreign subjects.

May cause electric shock.

May cause fire and damage to the product.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Warnings & Cautions

Detailed Warnings and Cautions

Cautions

- Avoid operating the camera for long durations under high temperatures and in high

humidity. Excessive heat can shorten the lifespan of the camera components.

Do not install under extreme

temperature conditions.

Do not install under unstable

lighting conditions.

- Do not install or place the camera near any heat sources.

- Subjecting the dome cover to physical shock may damage the camera and cause water

leakage into it.

- Do not place the camera facing direct sunlight or other intense light sources. Strong lights

such as spotlights can cause distortions—blooming and smear—as well as discolorations

on the screen by heating up the color filter of the camera.They also may cause internal

reflections of the camera, leading to operational malfunctions.

- Do not drop the camera or subject it to physical shock or vibration; this can cause serious

damage to the camera.

- When installing the camera near a power line, make sure to keep at least 1 meter distance

from the power line, or earth an additional metal pipe to separate the camera from the

power source.

Use only under temperature conditions between -0ºC

and +50ºC to prevent low graphics quality and product

malfunctions. When using in high temperature conditions,

provide good ventilation.

Severe lighting changes or flickering may hinder normal

camera operation.

Do not drop the camera or subject

it to physical shock.

Never keep the camera face to direct

sunlight or any other strong lights.

- This camera is to install on the ceiling. Installing it on the ground or a unleveled location

may cause product malfunctions and shorten its lifespan.

- This camera is provided with separate indoor and outdoor housings.When installing it in

an outdoor environment, use the outdoor housing.

- Avoid installing and operating the camera in the following places.

∙ Places whose temperature exceed the camera’s recommended range. (Indoor: -10℃ ~

50℃, Outdoor: Refer to the housing manual)

∙ Places where drastic temperature changes occur: e.g. Near an air conditioner.

May cause product malfunctions.

May cause critical damage to the CCD.

∙ Places that are exposed to steam, oil, and inflammable substances: e.g. Inside a kitchen.

∙ Places that are exposed to radioactivity, X-rays, strong electric waves, and electro-

magnetic waves.

Do not install in a place that may be

exposed to rain, water, or radioactivity.

Avoid touching the camera lens.

∙ Places that are exposed to outdoor air contaminants: e.g. Dust and car exhaust.

∙ Places in high humidity.

∙ Places that are exposed to corrosive gas: e.g. Next to the sea.

- Smeared and dusty dome covers decrease the picture and video quality. Clean the dome

cover and camera lens on a regular basis.

- Remove the plastic wrap on the dome cover only after the camera installation is complete.

- This camera is not equipped with a power switch. Plug in the camera only after the

installation is complete.

The lens is the most important component of the camera.

Be careful not to smear it with fingerprints.

Water leakage into the camera may cause damage.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Component Names and Functions

Components and Accessories

* Components

Front

Side

Power Adapter (AC 24V, Peak 2.5A)

User’s Manual

* Accessories

The following items are sold separately from the camera.

Housings

STH-380PO

Ultra Low-

Temperature

Heavy

STH-370PO

Low-

Temperature

Heavyweight

(-20℃~50℃)

STH-370PI

Indoor Housing

(-10℃~50℃)

(-40℃~50℃)

STH-370PEV

Flush-Mount

Indoor Housing

(-10℃~50℃)

STH-360PO

Low-

Temperature

Lightweight

(-20℃~50℃)

Bottom

Unlock Button

SW2: Communication DIP Switch

SW1: ID DIP Switch

Safety Wire Holder

Brackets

STB-350PPM

Parapet Mount

STB-340PCM

Corner Mount

STB-330PPM

Pole Mount

STB-25PF

Indoor Flange

STB-30PF

Indoor Flange

STB-370PC

Surface-mount

Install Base

STB-496PPV

Ceiling Bracket

STB-270PWV

Wall Bracket

STB-270B

Setup Box

Notes

ꢀ•ꢀꢀForꢀtheꢀDIPꢀswitchꢀsettings,ꢀpleaseꢀreferꢀtoꢀtheꢀ“InstallingꢀYourꢀCamera”ꢀonꢀPageꢀ17.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing Your Camera

Component Names and Functions

Speed Dome Camara and Appliances Wiring Diagram

Camera Wiring Interface Board (Sold Separately)

For the camera wiring, please refer to the picture below.

Connecting with Samsung Techwin’s “Stand Alone DVR”

The camera’s wiring interface board is equipped to a housing that is sold separately.

Video Output

· RS-485 :

Camera

D+

Stand Alone DVR

T(TX)+

Alarm

D-

T(TX)-

ꢀSVR-1680/1660/1645/960/

Alarm Output

·RS-422 :

Fan Heater

Connector

Camera

D+

Stand Alone DVR

T(TX)+

D-

T(TX)-

Alarm Input

ꢀSVR-945

TXD+

TXD-

R(RX)+

R(TX)-

Power Supply

Communications and AUX

ꢀSVR-940/450

ꢀSVR-1650/1640A/950E

Connecting with the Samsung Techwin Controller SCC-3100A

AC24V 2.5A

Power Input

Ground

·RS-485 :

SCC-3100A

Refer to the below Control

Signal Connection chart

Data Box PORT1

RX+

RX-

AUX Output

Camera

TX+

TX-

D+

D-

Control Signal Connection

Notes

· RS485 Communications

Controller

Camera

or DVR

ꢀ•ꢀꢀTheꢀmaximumꢀpowerꢀcapacityꢀofꢀtheꢀbuilt-inꢀ

relay is 30VDC/2A, 125VAC/0.5A, and

250VAC/0.25A.

ꢀ•ꢀꢀConnectingꢀtheꢀpowerꢀconnectorꢀandꢀGNDꢀ

incorrectly to the NC/NO and COM ports may

cause a short circuit and fire, damaging the

camera.

SCC-3100A

Data Box PORT1

·RS-422 :

D+

D-

TXD+

TXD-

Camera

TX+

TX-

· RS422 Communications

Camera

RX+

RX-

Controller

or DVR

TXD+

D+

D-

TXD-

TX+

TX-

D+

D-

TXD+

TXD-

RXD+

RXD-

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing Your Camera

Note!

Communication Protocol DIP Switch Settings (SW2)

* The following DVR models support all functions of the camera.

- 16Ch : SVR-1680/1660/1645/1650E/1640A

- 9Ch : SVR-960/945/950E

- 4Ch : SVR-440

* The following DVR models support only the Pan,Tilt, Zoom, and Focus functions of

the camera.

- 9Ch : SVR-940

- 4Ch : SVR-450

SW2 Pin No. Purpose

1~4

5~6

Protocol Settings

Baud Rate Settings

Transfer Method (RS-485/422) Settings

Response Mode Settings

Backup Mode Settings 1

Termination Settings

* Memo

10~11

MEMO

Backup Mode Settings 2

ꢀ•

Protocol Settings

Select a communication protocol for the camera

Protocol

Samsung

Pelco-D

SW2-#1

OFF

SW2-#2

OFF

SW2-#3

OFF

SW2-#4

OFF

Pelco-P

Samsung Elec.

Panasonic

Vicon

Honeywell

Reserved

OFF

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing Your Camera

ꢀ•

Baud Rate Settings

ꢀ•

Camera Backup Settings

Select the transfer speed of a selected communication protocol.

These settings are useful when the camera or its install base are damaged or malfunctions

occur.When replacing the camera or its install base, you can transfer existing presets and

sequence information to the replacement using these settings.

No.

Baud Rate(BPS)

2,400

SW2-#5

SW2-#6

OFF

4,800

Backup Function

SW2- #9

SW2- #12

OFF

9,600

OFF

→

Backup(IB D)

OFF

19,200

OFF

→

Backup(D IB)

OFF

Backup Disable

- Backup(IB→D) : Enables transferring the current camera's sequence information to a new

camera.

ꢀ•

Communication Method Settings

- Backup(D→IB) : Enables transferring the current camera's sequence information to a new

install base.

Select a communication method for the camera.

Function

Transfer Mode Switch

OFF

RS-485(2Wire)

*IB: Install base, D: Dome Camera

SW2- #7

RS-422(4Wire)

Notes

ꢀ•ꢀꢀToꢀuseꢀaꢀthirdꢀpartyꢀcontrollerꢀwithꢀthisꢀproduct,ꢀpleaseꢀcontactꢀourꢀAfter-SalesꢀServiceꢀorꢀ

Technology Department.

ꢀ•

Communication Response Settings

ꢀ•ꢀꢀADꢀProtocolꢀControlꢀMethod

- Input Camera OSD: 3+Auxiliary On

- Output Camera OSD: 3+Auxiliary Off

- Enter: IRIS Open

- ESC: IRIS Close

Select a communication response method for the camera and controller: Response or No

Response.

Function

OFF

SW2- #8

Response Mode Switch

Response

No Response

ꢀ•ꢀꢀForꢀmoreꢀinformationꢀaboutꢀtheꢀprotocols,ꢀreferꢀtoꢀourꢀofficialꢀwebsite.

Camera ID DIP Switch Settings (SW1)

ꢀ•

Termination Settings

To set up camera IDs, refer to the “Camera ID Chart” next.

To prevent the attenuation of communication signals between the camera and controller, 2

cameras in a longest distance for the camera and controller communication loop must be

set up with the termination settings.

Camera Input Position

Termination of Longest Path

On the Path

SW2- #10

SW2- #11

OFF

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing Your Camera

SW1-#1

OFF

SW1-#2

OFF

SW1-#3

OFF

SW1-#4

SW1-#5

OFF

SW1-#6

SW1-#7

OFF

SW1-#8

OFF

ꢀ•

Camera ID Chart

SW1-#1

ON/OFF

OFF

SW1-#2

OFF

SW1-#3

OFF

SW1-#4

OFF

SW1-#5

OFF

SW1-#6

OFF

SW1-#7

OFF

SW1-#8

OFF

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing Your Camera

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

SW1-#1

OFF

SW1-#2

OFF

SW1-#3

SW1-#4

OFF

SW1-#5

SW1-#6

OFF

SW1-#7

SW1-#8

OFF

SW1-#1

OFF

SW1-#2

OFF

SW1-#3

OFF

SW1-#4

OFF

SW1-#5

OFF

SW1-#6

OFF

SW1-#7

OFF

SW1-#8

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

OFF

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing Your Camera

171

SW1-#1

OFF

SW1-#2

OFF

SW1-#3

OFF

SW1-#4

SW1-#5

OFF

SW1-#6

SW1-#7

OFF

SW1-#8

SW1-#1

OFF

SW1-#2

OFF

SW1-#3

OFF

SW1-#4

OFF

SW1-#5

SW1-#6

OFF

SW1-#7

SW1-#8

214

215

216

217

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

255

OFF

212

213

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing Your Camera

Preparing and Installing Camera Bracket

Preparing Adapter and Cables

– Power Adapter

Power adapter has the capacity of AC24V 2.5A.

For the installation guidelines for the brackets and housings, refer to the user’s manual

enclosed with the bracket or housing that is sold separately.

Camera Wiring Diagram 1

•

– Video Cable

A BNC coaxial cable shown in the picture is required to connect Speed Dome’s video

output terminal to the monitor.

Distance

500m or shorter

500m or longer

Recommended Cable Specification

5C2V Coaxial Cable

7C2V Coaxial Cable

– Communications Cable

For the camera to communicate with the controller, a RS-485/422 communications line is

required.To ensure the quality of long distance communications and the accuracy of the

overall communications, using a twisted pair cable such as UTP Cable is recommended.

* Caution!

Depending on the camera’s environment, the communications distance may vary.

Notes

ꢀ•ꢀꢀNeitherꢀtheꢀvideoꢀnorꢀcommunicationsꢀcableꢀisꢀenclosedꢀwithꢀtheꢀcamera.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing Your Camera

Camera Wiring Diagram 2

•

On-Ceiling Mount Type Installation Example

1.Attaching Template and Installing STB-370PC

Attach the enclosed template to the ceiling, then drill a hole in the ceiling according to the

diameter marked on the template. Drop the camera cables down from the ceiling through

the hole. Next, install the exposed bracket STB-370PC to the ceiling as shown in the

picture.Before installing the exposed bracket, open the hinged door at the bottom of the

bracket as shown in the picture. Hold the knob on the hinged door to open.

Template

Knob

2.Wiring Terminal Cables

Connect the cables to the terminal block on the

hinged door. For the location of the wiring pins,

please refer to the “Camera Wiring Diagram”

on Page 14. Once the wiring is successful, close

the hinged door.

Notes

ꢀ•ꢀꢀDoꢀnotꢀconnectꢀtheꢀcameraꢀtoꢀaꢀpowerꢀoutletꢀuntilꢀtheꢀinstallationꢀisꢀcomplete.ꢀSupplyingꢀ

power in the middle of the installation may cause fire or damage the product.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Installing Your Camera

3. Setting Up Camera DIP Switches

✽

To attach or detach the camera, refer to the picture.

DIP switches for communication and ID protocols are located on the bottom of the

camera. For the switch settings, refer to the dip switch settings of this manual.

* Attaching the camera: Hold up the camera and push it to the mount as shown in the

picture. Push the camera until you hear a “click”.

* Detaching the camera:To detach the camera, pull the camera downward while pushing

the unlock buttons on the camera upward.

ID(SW1)

Protocol(SW2)

Unlock Button

UNLOCK

5. Connecting Camera Safety Cable and Attaching Camera

Carefully attach the camera to the mount following the alignment guide marks as shown

in the picture. First hook the camera's safety cable on the mount, and then attach the

camera.

To attach the

camera

To detach the

camera

Alignment

Direction

Guides

Safety

Cable

Alignment

Direction

Guides

Alignment

Directions

✽

To attach the camera to the mount, refer to the alignment guide marks as shown in the picture.

Notes

ꢀ•ꢀꢀMakeꢀsureꢀtoꢀfirstꢀhookꢀtheꢀcamera'sꢀsafetyꢀcableꢀtoꢀtheꢀmountꢀbeforeꢀproceeding.ꢀ

Otherwise you may be exposed to serious injury caused by a fallen camera.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating Your Camera

Interface Symbols

• Motion Detection Standby/Operation Display :

• OSD Menu Screen :

- When in standby mode, the " " in the upper right of the screen blinks and then

changes to " " if motion is detected.

• Alarm Input Port Status Display :

- "①","②","③" and "④" in the upper right of the screen blink.

• Current Alarm Port Display According to Input Alarm Ports(Priority) :

- Only one of " ꢁ"," ꢂ"," ꢃ"," ꢄ" in the upper right of the screen blinks.

• Preset Number Display Settings :

Camera Setting

Focus & Zoom

Sub Menu Available

①

Sub Menu Not Available

ꢂ White Balance

ATW

---

- '*' : If a preset number is already available

- 'H' : If a preset location is the camera’s home position

Operating Your Camera

- 'T' : If a preset location is the camera’s Auto Track starting point (SPD-3700T Only)

• If an OSD Menu has Sub Menus :

- The color of the circle around the menu number shows as embossed, e.g. "①".

• If an OSD Menu Does Not Have Sub Menus :

- The circle around the menu number shows as engraved, e.g. "ꢁ".

• Panning and Tilting

- Use the joystick of the controller or its direction buttons.

• Controlling Zoon

- Move the joystick clockwise (Tele) or counterclockwise (Wide), or use the Zoom

button.

• Accessing Screen Menus

- Press the Menu or OSD button on the controller.

Motion Detect

✽

For more detailed information about controls using a third party controller or a DVR, refer to the

user’s manual of the product.

• PTZ Function Screen :

Alarm Input

OSD Commands, Function Chart, and Menu Controls

ID=001

ꢁ①②③④

This dome camera can be operated using two methods: Using hot keys on its dedicated

controller, or accessing the OSD (On Screen Display) on the video output.The OSD menu

commands are as follows:

Area Display

Area1 Area Name

Command

Function

Move the joystick up/down/left/right

Enter/Focus Far

ESC/Focus Near

Moves the OSD menus up/down/left/right, respectively.

Selects a menu and allows access to the sub menus.

Cancels a command and moves back to an upper-level menu.

Sequence Status

Preset Info

G-SEQ1

PRESET=001 Preset Name

P:300 T:040 10X

Dome Cover Setting

Before optimizing the camera focus settings for the dome cover shape, please select the

dome cover type on the camera’s main menu. (Refer to Page 48)

• Preset Number Setting Screen :

Dome Cover Setting

Installation Type

Preset Edit

Preset=011* (1~255)

Outer

Inner

None

Dome cover type for outdoor housings except the indoor flush model.

Default dome cover type including the indoor flush model.

When using the camera without a dome cover.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating Your Camera

*OSD Menu Chart

③Group SEQ. Group1~6

④Tour SEQ. ①Setting②Execute③Clear

⑤PTZ Trace Trace1~4

①Setting②Execute③Clear

Default

One Shot AF

Auto

①Focus Mode

Auto/Manual/One Shot AF

①Replay②Memorize

Off/Home/Preset/Swing/Group/

Tour/Trace/A.Pan

①Focus

&Zoom

Mode

Auto/Tracking/Off

Slow/Medium/Fast Fast

②Zoom Tracking

③Digital Zoom

②

①Mode

Off

Speed

⑥Auto Run

Sequence

Setting

Off/2X/3X/4X/5X/.../12X

ATW/INDOOR/OUTDOOR/AWC

Off

AT W

117

Auto

F1.6

---

②Time

1~60(Sec), 1~60(Min)

30 Sec

⑦Power On

Resume

②White

Balance

On/Off

AWB Mode

Red

Blue

Manual

⑧MD Dwell

Time

①Off

②On

①Brightness

②Iris

0~100

Auto

Manual

1~60(Sec),1~60(Min)

①Position

②On/Off

①Position

②On/Off

30 Sec

Off

①Pan Limit

②Tilt Limit

Iris Level

①Pan/Tilt

Limit

③Exposure

③Shutter

④Sens-Up

①Off

---/A.FLK/Manual

Sens-Up Limit

X2/X4...X256

Off

Auto/Off

Auto(X2)

②Area Setting Area1~8

①Name/②Position/③On/Off

Off

Low

③Area

Mask1~8

Masking

①Position/②On/Off

Off

Level

Low/High

0~10

②HLC

④Back Light

Mask Color

Up/Down/Left/Right/

Increase/Decrease

④Prop.P/T

⑤Digital Flip

On/Off

①Camera

Setting

③User

⑥Image Hold On/Off

①Auto Track

Off

Off/Low/Medium/High

Medium

5 dB

Medium

⑤AGC

Manual

Level

5~41

On/Off

②Camera Height 2.5m~30m

Off

③P/T

Setting

⑥SSNR

Off/Low/Medium/High

2.5 m

Small

High

Off

Auto

③Object Size

④Sensitivity

⑤Zoom Control

⑥Auto Release

⑦Auto Return

⑧Lost Mode

Small/Medium/Large

Burst Level

0~100

Burst On/Off

Mode

Color

High/Medium/Low

Off/One Shot/Continuous

Off/10sec~5min

Off/1sec~5min

Stop/Research/Zoom Out

①Position

⑦Day

&Night

⑦Auto Track 1

⑧Auto Track 2

B/W

Duration

Slow/Fast

Fast

5 Sec

Dwell Time

5/7/10/15/20/30/40/60 Sec

Internal

Line Lock

Stop

Sync

Internal

Line Lock Phase

②Mode(Alarm/

Mask)

③On/Off

Stabilizer

Image Adj.

On/Off

Off

Inner

①Zone Setting

Zone1~8

Mask

⑧Others

①Preset

①Sharpness On(0~32)/Off

②Color

Off

0~100

②Indicator

③Target Lock

①Camera ID On/Off

Off/On/Pointer/Target

On/Off

Freeze

On/Off　

Dome Cover

Inner/Outer/None

①Setting②Edit③Home Position④Execute⑤Clear

⑥Status

②Camera

Name

①On/Off

②Edit

①Pan Swing

②Swing SEQ. ②Tilt Swing

③P&T Swing

①Setting②Execute③Clear

③Preset

Number

On/Off

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Operating Your Camera

Functional Description

④Preset

Name

①On/Off

②Edit

Camera Setting

Off

1. Focus and Zoom Settings

1.1 Focus Mode and Digital Zoom Setting Menu

⑤Sequence

Status

⑥Area Name On/Off

On/Off

④OSD

Setting

Off

▶

Main Menu/Camera Setting/Focus & Zoom

⑦PTZ

On/Off

Position

Focus Mode :

- Auto : Performs continuous auto-focus.

- Manual : Changes the camera mode to Manual Focus.

- One Shot AF :Auto-focuses the camera once after the

Pan,Tilt, or Zoom function is used.

⑧Language

①Alarm

Enable

English/Chinese/Fran ais/Deutsch/Espa ol/Italiano

English

Off

Main Menu

On/Off

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

①In1

MOD:NC/NO/OFF

Priority:1~4　

SEQ:Preset/Swing/Group/Tour/

A.Pan/Trace/Off

②In2

③In3

④In4

Out1~2

②Alarm Input

Off

Digital Zoom :

Enables the maximum digital zoom.

Setting the digital zoom to 12X provides a total zoom of

444x(SPD-3700T/3700)/396x(SPD-3310)/324x(SPD-2700).

⑤Alarm

Setting

1~4,MD,TRK

Off/On/Momentary

1~60(Sec),

③Alarm

Output

Status

Time1~2

Dwell Time

1~60(Min),

1~60(Hour)

➡

①On/Off

②Time

On/Off

1~60(Sec), 1~60(Min)

Off

④Aux. Output

Camera Setting

①Power On

Reset

①

ꢂ

③

④

ꢅ

ꢆ

⑦

⑧

Focus & Zoom

White Balance

Exposure

Back Light

AGC

Cancel/Execute

Off,1~7Days

Notes

ATW

②Factory

Default Set

③Camera

Default Set

④Auto

Refresh

⑤Auto Track

Default

ꢀ•ꢀꢀUnlikeꢀtheꢀopticalꢀzoom,ꢀtheꢀgraphicsꢀqualityꢀofꢀtheꢀ

digital zoom decreases as its zoom power increases.

ꢀ•ꢀꢀTheꢀauto-focusꢀfunctionꢀmayꢀnotꢀoperateꢀnormallyꢀ

under the following conditions :

- When background illumination is low

- While Slow-Shutter is in operation

⑥Initialize

⑦Status

Medium

SSNR

Off

Day & Night

Others

Cancel/Execute

- If the zoom level is set too high

- When background illumination is too high

- If a long distance object and a close distance object

appear together within a monitoring area

- If there is no contrast, e.g. the sky or a wall

- If the camera is facing a thin horizontal line

ꢀ•ꢀꢀAutoꢀFocusꢀfocusesꢀonꢀanꢀobjectꢀinꢀtheꢀcenterꢀofꢀtheꢀ

screen; objects around the screen edges may not be

properly in focus.

➡

Focus & Zoom

ꢁ

②

③

Focus Mode

ONE SHOT AF

Zoom Tracking

Digital Zoom OFF

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

2. White Balance

1.2 Zoom Tracking

▶

Main Menu/Camera Setting/Focus & Zoom/Zoom Tracking

Main Menu/Camera Setting/White Balance

Through this menu you can set up the camera’s focus mode

when zooming.

The White Balance menu adjusts the balance of the screen

colors under different lighting conditions.

Main Menu

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Mode :

- ATW :Adjusts the screen color automatically.

- Indoor :Adjusts the screen color to be optimal in an

indoor environment.

- Outdoor :Adjusts the screen color to be optimal in an

outdoor environment.

- AWC :Adjusts the screen color to be optimized to the

current lighting and monitor conditions. Using this

setting may require an readjustment if the lighting

conditions changes.

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

- Auto :Auto-focuses when zooming.

- Tracking : Focuses manually when zooming.

- Off : Disable the focus modes when zooming. (Full

manual mode)

Status

Speed :

Status

- Slow/Fast :Adjusts the zooming speed.

➡

Camera Setting

➡

- MANUAL : Enables customization the Red and Blue gains.

①

ꢂ

③

④

ꢅ

ꢆ

⑦

⑧

Focus & Zoom

White Balance

Exposure

Back Light

AGC

SSNR

Day & Night

Others

Camera Setting

ATW

①

ꢂ

③

④

ꢅ

ꢆ

⑦

⑧

Focus & Zoom

White Balance

Exposure

Back Light

AGC

ATW

Medium

OFF

Medium

SSNR

Day & Night

Others

➡

Focus & Zoom

ꢁ

②

③

Focus Mode

Zoom Tracking

Digital Zoom OFF

ONE SHOT AF

Notes

White Balance may not work properly under the following conditions.

ꢁWhen the color temperature of the environment surrounding the subject is out of the

control range.(e.g. Clear sky or sunset)

➡

ꢂWhen the ambient illumination of the subject is dim.

Zoom Tracking

ꢃ If the camera is directed towards a fluorescent light or is installed in a place where

illumination changes dramatically, White Balance adjustments may not deliver

consistent results.

ꢁ

②

Mode

AUTO

FAST

Speed

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

3. Exposure

4. Backlight

4.1 Backlight Mode Settings

▶

Main Menu/Camera Setting/Exposure

▶

Main Menu/Camera Setting/Back Light

The Exposure settings are to control the camera’s exposure

meter.

Main Menu

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Unlike other cameras, Samsung Techwin’s unique SV-IV DSP

chip gives you a clear image of the subject even with bright

backlight.

Main Menu

Brightness : Adjusts the screen brightness.

(Over 50: Brighter, Under 50: Darker)

Iris :

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

- Auto :Automatically adjusts the exposure meter.

- Manual : Enables manual adjustment of the exposure

meter. (Over 50: Brighter, Under 50: Darker)

Shutter : Controls the camera’s electronic shutter.

- --- :The shutter speed is fixed at 1/60 for NTSC and 1/50

for PAL. Operates when Iris is on the Auto Mode.

- ESC :Adjusts the shutter speed automatically according

to the screen brightness. Operates when Iris is on

the Manual Mode.

- A.FLK : Select this setting when you experience picture

flickering. Flickering can happen when artificial

lighting frequencies clash with camera frame rates.

- Manual : Enables manual adjustment of the shutter speed.

Sens-Up :

Back Light Mode

- Off : Disables the Backlight mode.

- HLC :Activates the High Light Compensation mode.

- User :Activates a user defined backlight compensation

mode.

Status

➡

Camera Setting

➡

①

ꢂ

③

④

ꢅ

ꢆ

⑦

⑧

Focus & Zoom

White Balance

Exposure

Back Light

AGC

Camera Setting

ATW

①

ꢂ

③

④

ꢅ

ꢆ

⑦

⑧

Focus & Zoom

White Balance

Exposure

Back Light

AGC

ATW

OFF

Medium

OFF

SSNR

- Auto :Automatically detects light levels and maintains a

clear picture at night or under low-light conditions.

- Sens-Up Limit :Adjusts to the maximum-powered zoom

per frame.

Medium

Day & Night

Others

SSNR

Day & Night

Others

➡

Notes

Exposure

ꢁ

ꢂ

ꢃ

ꢄ

Brightness

Iris

Shutter

Sens-Up

050

AUTO

---

ꢀ•ꢀꢀForꢀoptimalꢀperformanceꢀofꢀtheꢀA.FLKꢀmode,ꢀavoidꢀ

using the mode in conjunction with Backlight.

ꢀ•ꢀꢀWhileꢀtheꢀInternalꢀSyncꢀmodeꢀisꢀinꢀeffect,ꢀsettingꢀtheꢀ

shutter to '---' and facing the camera directly to a

bright light source may cause poor camera

performance.

AUTO

ꢀ•ꢀꢀSens-UpꢀisꢀdisabledꢀwhenꢀtheꢀshutterꢀisꢀinꢀManualꢀorꢀ

A.ꢀFLKꢀmode.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

4.2 HLC

4.3 User Area Setting

▶

Main Menu/Camera Setting/Back Light/HLC

▶

Main Menu/Camera Setting/Back Light/User

The HLC settings selectively eliminates high lights in a limited

environment such as the entrance to an apartment parking lot

or gas station, and is useful to detect a small objects like car

license plates.

HLC is disabled during the daytime.While monitoring

nighttime car traffic, if car headlamps reflect too bright lights

on the screen, the camera automatically eliminates the

headlamp lights and adjusts the colors of the license plate

accordingly.

Main Menu

You can selectively choose a screen area to see objects within

the area more clearly than others.

Main Menu

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Four-direction Joystick Controls :

- Moving the joystick in all four directions—upward,

downward, left, and right—adjusts the location and size

of a selected area.

Zoom Control :

- Zoom Tele : Enlarges the size of a selected area.

- Zoom Wide : Reduces the size of a selected area.

Status

➡

Camera Setting

HLC Masking Area

Camera Setting

①

ꢂ

③

④

ꢅ

ꢆ

⑦

⑧

Focus & Zoom

White Balance

Exposure

Back Light

AGC

SSNR

Day & Night

Others

①

ꢂ

③

④

ꢅ

ꢆ

⑦

⑧

Focus & Zoom

White Balance

Exposure

Back Light

AGC

SSNR

Day & Night

Others

ATW

HLC

Medium

USER

Medium

➡

Limit

➡

HLC Setting

Adjusts the HLC sensitivity level.

Mask Color

Adjusts the mask color on the highlighted area.

ꢁ

ꢂ

Limit

Mask Color

Medium

↑:Up↓:Down ←:Left →:Right

W:Decrease T:Increase

Notes

ꢀ•ꢀꢀEvenꢀifꢀHLCꢀisꢀon,ꢀcarꢀlicenseꢀplatesꢀmayꢀnotꢀbeꢀdetectableꢀdependingꢀonꢀtheꢀlocationꢀandꢀ

angle of the camera as well as the lighting condition.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

5. AGC

6. SSNR (Samsung Super Noise Reduction)

▶

Main Menu/Camera Setting/AGC

▶

Main Menu/Camera Setting/SSNR

AGC (Automatic Gain Control) adjusts the camera’s gain

control and the screen brightness if the camera has captured

an object under low-light conditions.

SSNR significantly reduces the amount of low luminance noise.

Main Menu

- Off : Disables the noise reduction function.

- Low : Reduces only a small amount of noise, but generates

almost no afterimage.

- Medium :The most commonly used mode. Reduces a suitable

amount of noise while generating a subtle

afterimage.

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

The Off, Low, Medium, High, and Manual modes are available.

- High : Reduces noise significantly, but generates obvious

afterimages.

Status

➡

Camera Setting

➡

Camera Setting

①

ꢂ

③

④

ꢅ

ꢆ

⑦

⑧

Focus & Zoom

White Balance

Exposure

Back Light

AGC

①

ꢂ

③

④

ꢅ

ꢆ

⑦

⑧

Focus & Zoom

White Balance

Exposure

Back Light

AGC

ATW

OFF

Medium

SSNR

Day & Night

Others

Day & Night

Others

Notes

ꢀ•ꢀꢀSSNRꢀisꢀdisabledꢀwhenꢀtheꢀAGCꢀmodeꢀisꢀturnedꢀoff.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

7. Day & Night

8. Others

▶

Main Menu/Camera Setting/Day & Night

▶

Main Menu/Camera Setting/Others

Sync

: Enables selecting Internal Synchronization or the

Main Menu

The Day & Night function allows the camera to switch

between the Color and B/W modes.

Main Menu

external Line Lock. (SPD-3700T not supported)

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

- Internal : Synchronizes the camera’s output timing to the

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Modes

internal crystal.

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

- Line Lock : Synchronizes the camera’s output timing to

the AC adapter power to synchronize multiple

cameras.This option is useful when using a

switch such as Matrix Switcher.

- Auto : Operates in Color mode most times, and switches

to B/W mode if a low light level is detected during

nighttime.

- Color : Operates in Color mode at all times.

- B/W : Operates in B/W mode at all times. By using the

Burst On/Off sub menu, burst signals can be

retained or disabled.

Status

- Line Lock Phase : Enables setting the adapter’s

synchronization phase between 0 and

360°.

Status

➡

Stabilizer

: The Stabilizer compensates for any small

movements of the camera caused by due to

the wind and other reasonsor other causes.

Camera Setting

✽ If the camera is in B/W mode and connected to equipment

that requires external sync through burst signals, set the

Burst On/Off option to “On.”

①

ꢂ

③

④

ꢅ

ꢆ

⑦

⑧

Focus & Zoom

White Balance

Exposure

Back Light

AGC

SSNR

Day & Night

Others

①

ꢂ

③

④

ꢅ

ꢆ

⑦

⑧

Focus & Zoom

White Balance

Exposure

Back Light

AGC

SSNR

Day & Night

Others

ATW

Notes

OFF

Medium

Duration

OFF

Medium

ꢀ•ꢀꢀTheꢀStabilizerꢀusesꢀtheꢀdigitalꢀzoomꢀandꢀmayꢀcauseꢀ

low picture quality.

ꢀ•ꢀꢀTheꢀStabilizerꢀisꢀdisabledꢀifꢀtheꢀambientꢀlightꢀisꢀtooꢀ

low.

ꢀ•ꢀꢀTheꢀStabilizerꢀisꢀdisabledꢀifꢀtheꢀfieldꢀofꢀviewꢀhasꢀveryꢀ

low or no contrast, e.g. The sky or a white wall.

The camera’s light sensitivity is adjustable as in the chart

below.The camera’s ambient light diversion performance

may vary depending on its environment.

Color -> B/W

2.5 Lux

B/W -> Color

4 Lux

Fast

➡

Slow

0.8 Lux

6 Lux

Others

Image Adj

Day & Night

- Sharpness : Sharpens outlines of an image.

- Color :Adjusts the color density of an image.

ꢁ

ꢂ

③

ꢄ

ꢅ

Sync

INTERNAL

OFF

Dwell Time

①

ꢂ

③

Mode

COLOR

Stabilizer

Image Adj

Freeze

The duration of both the lighting conditions can be

customized to let the camera divert between the daytime

and nighttime settings.

Duration

Dwell Time

FAST

Freeze

: Stops or reanimates an image.

0.5 SEC

Dome Cover

OFF

Inner

These settings are to optimize the camera’s focused object

position according to the dome cover type.

- Inner : Default dome cover type including the indoor flush

model. (Factory Release Mode)

Dome Cover

Notes

ꢀ•ꢀꢀTheꢀAutoꢀmodeꢀisꢀdisabledꢀwhenꢀAGCꢀisꢀturnedꢀoff.ꢀThisꢀfunctionꢀisꢀonlyꢀavailableꢀwhenꢀ

the Color or B/W mode is selected.

ꢀ•ꢀꢀUsingꢀB/Wꢀmodeꢀunderꢀsunlightꢀorꢀaꢀhalogenꢀlampꢀmayꢀdecreaseꢀtheꢀfocusingꢀ

- Outer : Dome cover type for outdoor housings except the

indoor flush model.

performance.

- None :When using the camera without a dome cover.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

Sequence Setting

10. Preset

10.1 Preset Location Saving

9. Power On Resume and MD Dwell Time

▶

Main Menu/Sequence Setting/Preset/Setting

▶

Main Menu/Sequence Setting

This function enables the memorization of a selected location

and activates the Pan,Tilt, and Zoom functions at that location.

Saved locations can be recalled using the Preset Execute

command.

Main Menu

Power On Resume

Main Menu

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

This is useful when the power is disconnected and

reconnected due to power failures or other power

interruptions.

If the camera was performing a sequence action prior to a

power disconnection, the camera automatically resumes

the action when the power is reconnected.

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Setting Up Preset Numbers

Selecting the Preset Setting menu brings up a screen as

shown below. Move the joystick in all four directions to

select the desired number.

Status

MD Dwell Time

Status

➡

When Motion Detection under the Preset Edit menu is

selected, MD Dwell Time performs the Tour or Group

function.

While the camera is performing a sequence action, if

motion is detected from a selected preset location, the

camera pauses the sequence action operation and starts

monitoring the location instead for a duration that is set

under the MD Dwell Time menu.

Preset Setting

Preset = 001 (255)

➡

Sequence Setting

①

②

③

④

⑤

⑥

ꢇ

ꢈ

Preset

①

②

③

④

⑤

⑥

ꢇ

ꢈ

Preset

Swing SEQ

Group SEQ

Tour SEQ

Swing SEQ

Group SEQ

Tour SEQ

Saving Preset Locations

Selecting a preset number and pressing the Enter key

redirects the menu to the screen shown below.

Using the joystick, adjust the location of the Pan and Tilt

functions and then set the Zoom and Focus command.

In Preset Settings, the Zoom and Focus command is

controllable only by the Zoom command.To switch

between Zoom and Focus, use the Preset 1 and 2

commands as shown below.

PTZ Trace

Auto Run

PTZ Trace

Auto Run

If the motion is no longer detectable or the duration

expires, the camera aborts the monitoring operation and

then resumes the sequence action.

Power On Resume

MD Dwell Time

Power On Resume

MD Dwell Time

OFF

➡

Preset

ꢁ

ꢂ

ꢃ

ꢄ

ꢅ

Setting

Edit

Execute

Clear

Status

Preset Setting Z>Z00M

1+PST:ZOOM 2+PST:FOCUS

Use W/T Preset

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

10.3 Preset Name Setting

10.2 Preset Edit

▶

Main Menu/OSD Setting/Preset Name/Edit

▶

Main Menu/Sequence Setting/Preset/Edit

Using this function, you can add names to preset locations.

up to 12 characters.

Once a name is entered, use the joystick and the Enter key to

perform the Set command and save the name.

You can edit the 13 preset items such as Pan/Tilt location,

Zoom and Focus, which are selected among camera functions.

Main Menu

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

①

②

Camera Setting

Sequence Setting

PTZ

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Recalls saved locations using the Preset Settings command.

....

Focus Mode

➡

Refer to the section entitled Setting Up Your Camera.

Sequence Setting

Brightness

Status

①

②

③

Preset

Swing SEQ

Group SEQ

Refer to the section entitled Setting Up Your Camera.

➡

Iris

OSD Setting

....

Refer to the section entitled Setting Up Your Camera.

➡

①

②

③

④

Camera ID

Backlight

Camera Name

Preset Number

Preset Name

Preset

Refer to the section entitled Setting Up Your Camera.

ꢁ

ꢂ

③

ꢄ

ꢅ

ꢆ

Setting

Edit

Home Position

Execute

Clear

Status

Day & Night

....

Refer to the section entitled Setting Up Your Camera.

OFF

After Act

➡

Enables setting up an automatic action after the camera

arrives at a selected preset location.

- TRACK : Commands the camera to perform the Auto

Tracking function.

- MD : Commands the camera to perform the Motion

Detection function.

Preset Name

ꢁ

ꢂ

ON/OFF

Edit

OFF

➡

Preset Edit

Preset = 001* (1~255)

Preset Edit

➡

- None : Select this when no action is desired.

Preset = 001* (1~255)

Preset Edit

[001]

Scene Adj

➡

Enables setting the Shutter,AGC, SSNR, Sens-Up,White

Balance, and Stabilizer functions. For more information

about interface terminology, please refer to the section

entitled Setting Up Your Camera.

ꢁ

ꢂ

ꢃ

ꢄ

⑤

ꢆ

ꢇ

⑧

PTZ

271/045/1X

ONE SHOT AF

050

PSET Name 001[

]

Focus Mode

Brightness

Iris

Back Light

Day & Night B/W

0123456789()[]#&%/~-=_

AUTO

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz

äöÖüÄÜàâçéèêëîïôûôùÿñÑáí

óúÀÂÇÉÈÊËïïÔßŒæÑÛÙŸÁÍÓÚÂ

ABC->中文1 BACK SPACE CLR SET

After Act.

Scene Adj.

OFF

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

11. Swing SEQ

10.4 Preset Execution/Deletion/Memory Check

▶

Main Menu/Sequence Setting/Swing SEQ

▶

Main Menu/Sequence Setting/Preset

Home Position

Sets one of the currently configured preset positions as the

home position.

The Swing function commands the camera to move between 2

selected locations, monitoring the route.

Main Menu

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Pan Swing

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Execute

Activates the Pan function for the Swing operation.

Tilt Swing

Recalls a saved preset location.

Activates the Tilt function for the Swing operation.

Clear

P&T Swing

Deletes the selected preset location.

Status

Activates both the Pan and Tilt functions for the Swing

operation.

Status

Opens a map of saved preset locations.

An area saved as a preset location is displayed with the

➡

Swing Settings/Execute/Clear

Sequence Setting

- Settings : Each of the Swing menus have sub menus with

'■' icon.

①

②

③

④

⑤

⑥

ꢇ

ꢈ

Preset

the settings.

①

②

③

④

⑤

⑥

ꢇ

ꢈ

Preset

Swing SEQ

Group SEQ

Tour SEQ

Swing SEQ

Group SEQ

Tour SEQ

➡

Preset Status

Pan Swing

001 :

021 :

041 :

061 :

081 :

101 :

121 :

141 :

161 :

□□□□□ □□□□□ □□□□□ □□□□□

PTZ Trace

Auto Run

①

②

③

Setting

Execute

Clear

PTZ Trace

Auto Run

□□□□□ □□□□□ □□□□□ □□□□□

Power On Resume

MD Dwell Time

Power On Resume

MD Dwell Time

OFF

➡

Pan Swing Setting

Swing SEQ

Preset

[001]←→[***]

①

②

③

Pan Swing

ꢁ

ꢂ

③

ꢄ

ꢅ

ꢆ

Setting

Tilt Swing

P&T Swing

Edit

➡

SPEED=64 (1~64)

Home Position

Execute

Clear

OFF

DWT =003(1~128)(s)

Preset Status

181 :

201 :

221 :

241 :

□□□□□ □□□□□ □□□□□ □□□□□

Select 2 preset locations by using the joystick.

Speed indicates the camera’s movement speed. DWT indicates

the camera’s duration of stay at a preset location.

- Execute: Executes the Swing operation.

□□□□□ □□□□□ □□□□□ □□□□□

Status

- Clear: Deletes data in the Swing memory.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

12. Group SEQ

13. Tour SEQ

▶

Main Menu/Sequence Setting/Group SEQ

▶

Main Menu/Sequence Setting/Tour SEQ

Selecting Group SEQ recalls a group of multiple preset

locations in a consecutive manner.A group can contain up to

255 preset locations.

Main Menu

Selecting Tour SEQ recalls groups of preset locations in a

consecutive manner. Up to 6 groups can be listed for this

function.

Main Menu

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Setting

Settings

Using the joystick, enter desired preset numbers into the

PSET section. DWT indicates the camera’s duration of stay

at a preset location. SPD shows the camera’s movement

speed by 64 different levels.

Selecting the Settings menu brings up the following screen.

Using the joystick, you can enter desired group numbers to

the Group section. DWT indicates the camera’s standby

time before a new group is recalled.

Status

➡

Group SEQ 1

Sequence Setting

Tour SEQ

Sequence Setting

PSET DWT(s) SPD

①

②

③

④

⑤

⑥

ꢇ

ꢈ

Preset

Group

DWT(s)

003

001: *** : 003 : 64

002: *** : 003 : 64

003: *** : 003 : 64

004: *** : 003 : 64

005: *** : 003 : 64

006: *** : 003 : 64

007: *** : 003 : 64

①

②

③

④

⑤

⑥

ꢇ

ꢈ

Preset

Swing SEQ

Group SEQ

Tour SEQ

PTZ Trace

Auto Run

01: *

02: *

03: *

04: *

05: *

06: *

Swing SEQ

Group SEQ

Tour SEQ

PTZ Trace

Auto Run

003

Power On Resume

MD Dwell Time

OFF

Power On Resume

MD Dwell Time

OFF

➡

Execute

➡

Group SEQ

Executes the group operation.

Clear

Deletes the selected group.

Clear

Tour SEQ

①

②

③

④

Group 1

Group 2

Group 3

Group 4

Deletes the selected group.

ꢁ

ꢂ

ꢃ

Setting

Execute

Clear

....

➡

Group SEQ 1

ꢁ

ꢂ

ꢃ

Setting

Execute

Clear

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

14. PTZ Trace

15. Auto Run

▶

Main Menu/Sequence Setting/PTZ Trace

▶

Main Menu/Sequence Setting/Auto Run

Maximum 4 patterns of the manual operation paths (for Pan,

Tilt, Zoom and Focus) are memorized and replayed.

Main Menu

If there is no controller operation by the user for a certain time,

the sequence operation designated by the user will be

executed.

Main Menu

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Replay

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Replays a route saved by the Trace function. Use the Stop

button to stop the replay.

Mode

- Home :Auto run Home Position (Refet to the Preset

Menu.)

Memorize

Up to 120 seconds of a memory can be saved.The memory

duration varies depending on the difficulty level of the PTZ

Trace action. If the memory capacity is full, the Over

message appears and the memorization action is

terminated.

- Preset :Auto run a selected preset number.

- Swing :Auto run a selected Swing mode.

- Group :Auto run a selected Group mode.

- Tour :Auto run a selected Tour mode.

- Trace :Auto run a selected trace mode.

- A.Pan :Auto run a 360-degree pan.To activate the

panning command, you need to set up the

camera's tilt angle and auto pan speed manually.

Status

➡

Sequence Setting

①

②

③

④

⑤

⑥

ꢇ

ꢈ

Preset

①

②

③

④

⑤

⑥

ꢇ

ꢈ

Preset

Swing SEQ

Group SEQ

Tour SEQ

Swing SEQ

Group SEQ

Tour SEQ

PTZ Trace

Auto Run

Time

PTZ Trace

Auto Run

Enables setting up an Auto Run duration. (The duration can

be 1~60 seconds, or 1~60 minutes.)

Power On Resume

MD Dwell Time

Power On Resume

MD Dwell Time

OFF

➡

PTZ Trace

Auto Run

①

②

③

④

Trace 1

Trace 2

Trace 3

Trace 4

ꢁ

ꢂ

Mode

Time

OFF

30 SEC

➡

PTZ Trace 1

ꢁ

ꢂ

Replay

Memorize

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

P/T Setting

17. Area Setting

▶

Main Menu/P/T Setting/Area Setting

16. Pan/Tilt Limit

▶

Main Menu/P/T Setting/Pan/Tilt Limit

The moving ranges in the Pan/Tilt directions can be limited.

Position

The Area Setting menu enables selecting certain locations in

the course of the Pan and Tilt operation, and then display the

areas with the OSD (On Screen Display) texts when the camera

passes through them. Up to 8 areas can be selected.

Main Menu

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Main Menu

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Area Name

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Selecting the Position menu brings up the following screen

if it is for the Pan Limit setting. Move the joystick left and

right to select a movement range from the starting point to

the end.

You can add names to selected areas. Names can be up to

12 characters and can be entered via the joystick and the

Enter key. Once a name is entered, use the joystick and the

Enter key to perform the Set command and save the name.

Status

➡

Status

P/T Setting

Start Limit

End Limit

Area Name 001[

0123456789()[]#&%/~-=_

]

①

②

③

ꢄ

ꢅ

ꢆ

⑦

⑧

Pan/Tilt Limit

Area Setting

Area Masking

Prop. P/T

Digital Flip

Image Hold

➡

P/T Setting

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz

äöÖüÄÜàâçéèêëîïôûôùÿñÑáí

óúÀÂÇÉÈÊËïïÔßŒæÑÛÙŸÁÍÓÚÂ

ABC->中文1 BACK SPACE CLR SET

⇨

OFF

①

②

③

ꢄ

ꢅ

ꢆ

⑦

⑧

Pan/Tilt Limit

Area Setting

Area Masking

Prop. P/T

Enter: Set

ESC: Exit

Enter: Set

ESC: Exit

Auto Track1

Auto Track2

Digital Flip

Image Hold

The following picture shows the Tilt Limit setting.

Move the joystick left and right to select a movement

range from the starting point to the end.

OFF

Position

➡

Auto Track1

Auto Track2

As shown in the picture below, move the joystick to select

the upper left corner and lower right corner of an area.

Area Setting

①

②

③

④

Area 1

Area 2

Area 3

Area 4

Start Limit

End Limit

➡

Start Position

End Position

Pan/Tilt Limit

①

②

Pan Limit

⇨

....

⇨

Tilt Limit

➡

Pan/Tilt Limit

Enter: Set

ESC: Exit

Enter: Set

ESC: Exit

Area 1

Enter: Set

ESC: Exit

Enter: Set

ESC: Exit

ꢁ

ꢂ

ꢃ

Area Name

On/Off

①

②

Position

ON/OFF

Position

ON/OFF

On/Off

Cancels or activates the Pan/Tilt Limit functions.

OFF

Cancels or activates the display function of selected areas.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

18. Area Masking

19. Prop. P/T

▶

Main Menu/P/T Setting/Area Masking

▶

Main Menu/P/T Setting/Prop. P&T

If a monitoring location includes a highly private area, the area

can be selectively excluded from monitoring.

Main Menu

This commands the camera to change the Pan and Tilt speed

automatically according to the current zoom power. Moving

the joystick clockwise (Tele) slows down and counterclockwise

(Wide) accelerates the Pan and Tilt speed, allowing detailed

adjustments.

Main Menu

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Position

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

As shown in the picture below, move the joystick to select

the upper left corner and lower right corner of an area.

Turning this “Off” executes the function the optical 1x zoom

speed regardless of how high a the zoom power is.

Status

Start Position

End Position

Status

➡

P/T Setting

⇨

P/T Setting

①

②

③

ꢄ

ꢅ

ꢆ

⑦

⑧

Pan/Tilt Limit

Area Setting

Area Masking

Prop. P/T

①

②

③

ꢄ

ꢅ

ꢆ

⑦

⑧

Pan/Tilt Limit

Area Setting

Area Masking

Prop. P/T

Enter: Set

ESC: Exit

Enter: Set

ESC: Exit

Digital Flip

Image Hold

Digital Flip

Image Hold

On/Off

OFF

Cancels or activates the Area Masking function.

Auto Track1

Auto Track2

Auto Track1

Auto Track2

➡

Area Setting

①

②

③

④

Mask 1

Mask 3

Mask 4

....

➡

Mask 1

ꢁ

ꢂ

Position

ON/OFF

OFF

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

20. Digital Flip

21. Image Holding

▶

Main Menu/P/T Setting/Digital Flip

▶

Main Menu/P/T Setting/Image Hold

When the camera is moving between preset locations, this

function stops a previous camera feed until the camera

reaches the next location.This is useful to help the screen

observer keep sharp eyes and to monitor multiple locations

within a network.

Digital Flip is useful to monitor a moving object or a person

passing directly under the camera.

Main Menu

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

When an object or a person passes directly under the camera,

the camera tilt monitor follows the object or person over 100

degrees to the other side of the tilt area without panning.The

screen inversion occurs at 100 degrees or higher and is

digitally adjusted.

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Status

➡

P/T Setting

①

②

③

ꢄ

ꢅ

ꢆ

⑦

⑧

Pan/Tilt Limit

Area Setting

Area Masking

Prop. P/T

①

②

③

ꢄ

ꢅ

ꢆ

⑦

⑧

Pan/Tilt Limit

Area Setting

Area Masking

Prop. P/T

Digital Flip

Image Hold

Digital Flip

Image Hold

OFF

Auto Track1

Auto Track2

Auto Track1

Auto Track2

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

Auto Release

22. Auto Track 1 (SPD-3700T Only)

▶

Enables setting a maximum duration to follow an object.When the duration expires, the camera

Main Menu/P/T Setting/Auto Track1

stops following the object and returns to the start position to follow another objects.

This function is available only with the SPD-3700T.

This commands the camera to automatically follow a moving

object or a person on the screen.

Auto Return

Main Menu

- Off : Commands the camera to stay on a last spot instead of returning to the initial position.

- Time Setting : Sets a duration for the camera to standby upon the Auto Release expiration and

then return to the start position.

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Auto Track

Lost Mode

On/Off:Turns Auto Track on or off.

Sets up an action for the camera in case the object it is following goes out of the detection

range.

- Stop : Commands the camera to stop and abort tracking at the spot where its object

Camera Height

Adjusts the height of the camera.Tracking performance

may decrease if the camera height is not adjusted properly.

Status

disappeared.

➡

Object Size

- Research : Commands the camera to stop and standby at the spot where its object

P/T Setting

Sets a maximum zoom power to zoom in on an object if

the Zoom function is used for the tracking operation.

- Small : Zooms in on a tracking object up to 1/4 of the

screen height.

- Medium : Zooms in on a tracking object up to 2/4 of the

screen height.

disappeared.

- Zoom-Out : Commands the camera to zoom out and look for a new object in case its current

object disappears.

①

②

③

ꢄ

ꢅ

ꢆ

⑦

⑧

Pan/Tilt Limit

Area Setting

Area Masking

Prop. P/T

Digital Flip

Image Hold

OFF

- Large : Zooms in on a tracking object up to 3/4 of the

screen height.

Auto Track1

Auto Track2

Sensitivity

The object detection sensitivity is adjustable. Lower the

sensitivity if the camera catches a swaying tree branch,

raindrops, or snowflakes during the Auto Track operation.

➡

Auto Track 1

ꢁ

ꢂ

ꢃ

ꢄ

ꢅ

ꢆ

ꢇ

ꢈ

Auto Track

OFF

Zoom Control

Camera Height

Object Size

Sensitivity

Zoom Control

Auto Release

Auto Return

Lost Mode

02.5M

SMALL

HIGH

OFF

The function’s zoom control settings are as follows.

- Off : Disables the Zoom control.

- One Shot : Performs the Zoom control once during the

Motion Detection and Auto Track operations.

Depending on the movement detection, the

camera performs the Zoom control multiple

times.

OFF

STOP

- Continuous : Performs the Zoom control continuously.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

- Target : Indicates the camera’s target for the Auto Track operation; when a moving object is

detected, a square grid appears and surrounds the object.

23. Auto Track 2 (SPD-3700T Only)

▶

Main Menu/P/T Setting/Auto Track2

Target Lock

This function is available only with the SPD-3700T.

Auto Track 2 provides Auto Track related settings other than

the ones programmed in the Auto Track 1 menu.

Target Lock is useful to select and follow an object using the Auto Track mode while operating

the camera with the joystick.Target Lock can be turned On or Off.

To activate the Auto Track mode, turn on Target Lock, select an object to follow, and then press

Enter.

Main Menu

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Zone Setting

- Position : Enables designating certain areas as zones for

the Auto Track operation.The setting procedures

are the same as for Area Mask.

- Mode :Two modes are available: Mask and Alarm. When

Mask is selected, the camera does not follow the

object entering the masked zone. This is useful if

the camera catches swaying objects such as tree

branches and flags during the Auto Track peration.

When Alarm is selected, the camera activates an

alarm if an object enters the zone.

Status

➡

P/T Setting

①

②

③

ꢄ

ꢅ

ꢆ

⑦

⑧

Pan/Tilt Limit

Area Setting

Area Masking

Prop. P/T

Notes

- On/Off :Activates or deactivates the Zone function.

ꢀ•ꢀꢀAutoꢀTrackꢀisꢀspecificallyꢀtoꢀtrackꢀdownꢀintruders.ꢀThus,ꢀitꢀmayꢀnotꢀbeꢀsuitableꢀtoꢀmonitorꢀaꢀ

crowd.

ꢀ•ꢀꢀIfꢀtheꢀcameraꢀisꢀnotꢀsafelyꢀsecured,ꢀtrackingꢀerrorsꢀmayꢀoccur.

ꢀ•ꢀꢀIfꢀtheꢀcameraꢀlensꢀisꢀsmearedꢀwithꢀforeignꢀsubstancesꢀorꢀisꢀscratched,ꢀanꢀerrorꢀmayꢀ

occur causing the camera to not behave as expected.

ꢀ•ꢀꢀTheꢀcameraꢀmayꢀnotꢀfollowꢀanꢀobjectꢀorꢀtrackingꢀerrorsꢀmayꢀoccurꢀunderꢀtheꢀfollowingꢀ

conditions:

∙ If the contrast between an object and the background is low

∙ If the camera lens is smeared with foreign substances, e.g. raindrops or snowflakes

∙ If the lighting is changing dramatically

∙ If many movements around an object are detected

∙ If an object moves vertically on the optic angle of the camera

∙ If an object passes directly under the camera

∙ If an object creates inconsistent light levels, e.g. the object is too shiny or flickering

∙ In environments where there are light reflections causing internal reflections of camera,

e.g. windows, shiny road surfaces, and backlights

∙ If an object moves behind large and tall objects, e.g. telephone poles

∙ If an object moves too quickly

Digital Flip

Image Hold

OFF

Track Zone

① Zone 1

Zone 1

Auto Track1

Auto Track2

① Position

② Zone 2

③ Zone 3

④ Zone 4

⑤ Zone 5

⑥ Zone 6

⑦ Zone 7

⑧ Zone 8

② Mode

MASK

OFF

③ ON/OFF

⇨

➡

Auto Track 2

①

ꢂ

ꢃ

Zone Setting

Indicator

OFF

Target Lock

Indicator

Indicates objects with icons on the screen.

- Off : Disables the Indicator function.

- On : Indicates both the pointer and target.

- Pointer : Indicates the indicator when following an object

using the joystick; shows as a cross in the center

of the screen.

∙ If the camera is vibrating

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

OSD Setting

Alarm Setting

24. OSD Setting

25. Alarm Setting

25.1. Setting Up Alarm Input

▶

Main Menu/OSD Setting

▶

Main Menu/Alarm Setting/Alarm Input

Camera ID

Main Menu

Displays or hides Camera ID in the upper left of the screen.

Camera Name

Add a name to the camera. (First check the Note.)

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Alarm Enable

Main Menu

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

- On/Off : Enables or disables the Alarm function.

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

MOD

Preset Number

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Enables selecting an Alarm Input method.

- NO (Normally Open)

Displays or hides Preset Numbers on the screen.

Preset Name

Status

Add names to preset locations. (First check the Note.)

IN 1.2.3.4

Sequence Status

Displays or hides the status of a sequence action that is in

progress.

➡

Status

OSD Setting

⇨

➡

①

②

③

ꢄ

ꢅ

ꢆ

⑦

⑧

Camera ID

Area Name

Camera Name

Preset Number

Preset Name

Alarm Setting

ALM GND

ALARM ON

Displays or hides the Area Name for the Area Settings on

the screen.

ꢁ

②

③

④

Alarm Enable

Alarm Input

Alarm Output

Aux Output

OFF

ALARM OFF

PTZ Position

Sequence Status ON

Area Name

PTZ Position

Language

OFF

English

Displays or hides the status of the Pan,Tilt, and Zoom

operation that is in progress.

Language

- NC (Normally Closed)

➡

Enables changing the system language.This camera

supports English, Chinese, French, German, Spanish, and

Italian.

ALM MOD P SEQ. NO

IN 1.2.3.4

ALM GND

ꢁ

ꢂ

ꢃ

ꢄ

IN1 OFF 1

IN2 OFF 2

IN3 OFF 3

IN4 OFF 4

OFF

XXX Name 001[

0123456789()[]#&%/~-=_

]

ALM GND

✽

When selecting the Camera Name and Preset

Name, the screen displays the Left keypad.

ABCDEFGHIJKLMNOPQRSTUVWXYZ

abcdefghijklmnopqrstuvwxyz

äöÖüÄÜàâçéèêëîïôûôùÿñÑáí

óúÀÂÇÉÈÊËïïÔßŒæÑÛÙŸÁÍÓÚÂ

ABC->中文1 BACK SPACE CLR SET

ALARM OFF

ALARM ON

Names can be up to 12 characters and can be

entered via the joystick and the Enter key. Once a

name is entered, use the joystick and the Enter key

to perform the Set command and save the name.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

25.2. Alarm Output

Notes

▶

Main Menu/Alarm Setting/Alarm Output

ꢀ•ꢀꢀAsꢀshownꢀinꢀtheꢀpictureꢀabove,ꢀtheꢀAlarmꢀInputꢀmustꢀbeꢀenteredꢀwithꢀtheꢀOpenꢀandꢀCloseꢀ

switch signals. Supplying power without entering the signals may damage the product.

Setting 1,2

Main Menu

Enables selecting an Alarm Output method.

- 1, 2, 3, 4, and MD on the menu selection indicate the

alarm input port and motion detection input. Up to 4

alarm inputs can be set for each MD (Motion Detection)

and TRK (Auto Track). 1 alarm output port can be used for

more than 2 alarm inputs along with ones for MD and

TRK.

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

P (Priority)

Set the priority of Alarm Inputs. If more than one alarm is simultaneously activated,

the alarm with the highest priority activates before the others. Once the alarm is canceled, the

next highest priority alarm activates.

SEQ

Status

✽The TRK function becomes activated only if the Zone mode

under Zone Settings under Auto Track 2 is set to Alarm.

Enables setting up a sequence action for the camera in response to an alarm.Available

sequence actions are Preset, Swing, Group,Tour,Trace and A.Pan.

➡

Timer

Alarm Setting

Enables selecting an Alarm Output method.

- On : Retains an alarm output for a set duration from a

minimum of 1 second to a maximum of 60 hours

upon the alarm occurrence.

ꢁ

②

③

④

Alarm Enable

Alarm Input

Alarm Output

Aux Output

OFF

- Momentary : Retains an alarm output only until the alarm

is canceled.

✽The Alarm Output is equipped with a relay circuit.The

operation of the alarm output port is as shown in the

diagram below.

➡

Alarm Output

ꢁ

ꢂ

ꢃ

ꢄ

Setting1

Setting2

Timer

□1 □2 □3 □4

1 OFF

□

TRK

Timer

1 OFF

COM

⇨

Alarm Out OFF

Alarm Out ON

Notes

ꢀ•ꢀꢀConnectingꢀtheꢀpowerꢀconnectorꢀandꢀGNDꢀincorrectlyꢀtoꢀtheꢀNC/NOꢀandꢀCOMꢀportsꢀmayꢀ

cause a short circuit and fire, damaging the camera.

ꢀ•ꢀꢀTheꢀmaximumꢀpowerꢀcapacityꢀofꢀtheꢀbuilt-inꢀrelayꢀisꢀ30VDC/2A,ꢀ125VAC/0.5A,ꢀandꢀ

250VAC/0.25A. Operating the camera beyond the capacity may decrease the camera’s

lifespan and damage it.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

25.3. Aux Output

Initialize

▶

Main Menu/Alarm Setting/Aux Output

26. Initialization Menu

▶

Main Menu/Initialize

AUX Output menu is to operate the camera’s peripheral

devices such as lamps and sirens through the controller and

switches as well as through network communications.

Main Menu

Power On Reset

Main Menu

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Restarts the camera.

Factory Default

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

On/Off

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Enables resetting the camera to its factory default settings.

When the mode is selected, all custom data such as preset

locations is deleted from the camera.

Use this function if it is necessary to reset the settings of

the camera.

- Cancels or activates the Aux function.

Time

Enables setting up a duration for the Aux output when the

Aux command is transmitted from the controller.A

duration can be selected from a minimum of 1 second to a

maximum of 60 minutes.

Status

➡

Camera Default

➡

Alarm Setting

This mode can be used if the camera module has been

replaced and you want to keep the camera's existing

settings for the new module.

To do reset the camera, first replace the old module with a

new camera module.When the replacement is properly

installed, turn on the module, then execute this command.

Initialize

ꢁ

②

③

④

Alarm Enable

Alarm Input

Alarm Output

Aux Output

OFF

①

②

③

ꢄ

⑤

Power On Reset

COM

⇨

Factory Default

Camera Default

Auto Refresh

AUX Off

AUX On

OFF

➡

Auto Refresh

Auto Track Default

AUX Output

Enables optimizing the status of the camera’s built-in

electric circuits and components on a regular basis. (A

regular operation can be scheduled.)

ꢁ

ꢂ

On/Off

Time

OFF

00 SEC

This mode can be used to maintain and repair the current

settings of the camera when anomalous operations occur:

e.g.The camera happened to directly face a light source, or

the settings have been canceled after the camera

repeatedly rotated in all four directions for a long time to

monitor a specific location.

Notes

ꢀ•ꢀꢀConnectingꢀtheꢀpowerꢀconnectorꢀandꢀGNDꢀincorrectlyꢀtoꢀtheꢀAuxꢀterminal’sꢀNOꢀandꢀCOMꢀ

ports may cause a short circuit and fire, damaging the camera.

ꢀ•ꢀꢀTheꢀmaximumꢀpowerꢀcapacityꢀofꢀtheꢀbuilt-inꢀrelayꢀisꢀ30VDC/2A,ꢀ125VAC/0.5A,ꢀandꢀ

250VAC/0.25A. Operating the camera beyond the capacity may decrease the camera’s

lifespan and damage it.

The default setting is Off.

- Off, 1~7 Days: Selecting Off disables Auto Refresh and but

automatically executes it after 1~7 Days days has passed.

action once the refresh is complete.

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional Description

Operating Your Camera

✽Auto Refresh takes approximately 10 seconds to finish. If Auto Refresh activates in the middle of a

sequence action, the camera pauses the sequence action and performs an Auto Refresh, then

resumes the sequence action once the refresh is complete.

Status

27. Status

▶

Main Menu/Status

Auto Track Default

Enables resetting the Auto Track settings.

Displays the settings and version of the dome camera.

Cam Model

Main Menu

①

②

③

④

⑤

⑥

ꢇ

Camera Setting

Sequence Setting

P/T Setting

OSD Setting

Alarm Setting

Initialize

Indicates the model name of the camera.

Cam Version

Indicates the software version of the camera.

Dome Version

Indicates the version of the camera control board.

CON Protocol

Status

Indicates the status of the current protocol.

Dome ID

➡

Camera Status

Dome Camera ID

Controller

CAM MODEL

= 37PC

CAM VERSION = 2.3

Indicates the settings of the current communications mode.

Track Version

DOME VERSION = 0.10

CON PROTOCOL = SAMSUNG TW

Indicates the Auto Track software version of the camera.

DOME ID

= 001

CONTROLLER

= Simplex-9600

TRACK VERSION= 0.10

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Product Specification

Sens-up

On/Off (Selectable limit ~ 256X )

LOW/MEDIUM/HIGH/MANUAL/OFF

ATW/INDOOR/OUTDOOR/AWC/MANUAL

AUTO(NTSC:1/60~120,000sec, PAL:1/50~120,000sec)/MANUAL/A.FLK

SPD-3700T

SPD-3700

SPD-3310

SPD-2700

Gain Control

White Balance

Electronic Shutter

Serial Com.

Protocol

Alarm

Digtal Flip

Operating Temperature/

Humidity

Storage Temperature/

Humidity

Input Voltage

Power Consumption

External Dimensions

(Ø×D)

Imaging Device

TV Standard

Total Pixels

1/4 inch, Super HAD color CCD

NTSC / PAL

NTSC:811(H) x 508(V) / PAL:795(H) x 596(V)

NTSC:768(H) x 494(V) / PAL:752(H) x 582(V)

2:1 Interlace

RS-422/485

Effective Pixels

Samsung Techwin, Pelco-D, Pelco-P, Panasonic, Honeywell,AD,Vicon, Samsung Electronics

Scanning System

Synchronization

Horizontal Scan Rate

Vertical Scan Rate

Horizontal Resolution

4 In, 2 Out, 1 Aux

ON/OFF

Internal

Internal/External(AC Line Lock)

NTSC:15.734 KHz / PAL:15.625 KHz

NTSC:59.94 Hz / PAL: 50 Hz

℃

-10 to +50 / 20% to 80% RH

550 TV Line(Color)/680 TV Line(B/W)

0.4 Lux @ F1.6 ( Color ), 0.001Lux @ F1.6 (Sens-up 256X)

℃

-20 to +60 / 20% to 95% RH

Min. Illumination

0.02 Lux @ F1.6 ( B/W )

AC24V 10%

Max. 13W

S/N (Y Signal)

Video Output

50 dB

Max. 15W

CVBS:1.0Vp-p/75Ω

33X (Optical),

27X(Optical),

12X(Digital)

3.5~94.5mm

(F1.6~2.9)

Ø155×243.4mm

2Kg

Zoom Ratio

37X (Optical),12X (Digital)

12X (Digital)

3.5~115.5mm

(F1.6 ~3.6)

Weight

Focal Length

3.5~129.5mm (F1.6 ~3.9)

Min. Object Distance

1.9m

H:55.5°(Wide)

~1.77°(Tele)

V:42.5°(Wide)

~1.33°(Tele)

H:55.5°(Wide)

~2.24°(Tele)

V:42.5°(Wide)

~1.79°(Tele)

H:55.5°(Wide)~1.59°(Tele)

V:42.5°(Wide)~1.19°(Tele)

Angular Field

of view

Focus

Zoom Speed

IRIS

AUTO / MANUAL / ONE-SHOT

2.5sec

AUTO/MANUAL

Lens Initialization

Auto Tracking

Horizontal

Built-In

360° Endless

Rotation Angle

Horizontal

Manual:0.024°/sec ~120°/sec, Preset 500°/sec

Rotation Speed

Vertical Rotation Angle

Vertical Rotation Speed

Preset Position

Preset Accuracy

Camera ID

-5° ~ 185°

Manual:0.024°/sec ~120°/sec, Preset 500°/sec

255

0.1°

255

Day & Night

Backlight

Motion Detection

Stabilizer

AUTO / COLOR / BW

USER / HLC / OFF

ON/OFF

Privacy Mask

SSNR

ON/OFF (8 Areas)

LOW/MEDIUM/HIGH/OFF

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

DECLARATION OF CONFORMITY

MEMO

Application of Council Directive(s)

EMC-Directive 92/31 EEC and its amendments

Manufacturer's Name

Manufacturer's Address

ꢀ

SAMSUNG TECHWIN CO., LTD

42,ꢀSUNGJU-DONGꢀCHANGWON-CITY,

KYUNGNAM,ꢀKOREA,ꢀ641-716

ꢀ

European Representative Name

European Representative Address

Equipment Type/Environment

Model Name

Dome Camera

SPD-3700T/3700/3310/2700

S8110001

Beginning Serial NO.

YearꢀofꢀManufactureꢀꢀ

Conformance to

2008.11.29

EN 55022 : 2006

EN 50130-4 : 2003

We, the undersigned, hereby declare that the equipment specified above conforms

to the above Directive(s).

Manufacturer SAMSUNG TECHWIN CO., LTD

Signature

Legal Representative in Europe

Signature

FullꢀNameꢀꢀ

Positionꢀꢀ

Placeꢀ

FullꢀNameꢀꢀ

Positionꢀꢀ

Placeꢀꢀ

HANꢀSEUGꢀKIMꢀ

QUALITYꢀCONTROLꢀMANAGERꢀꢀ

CHANGWON,ꢀKOREAꢀ

2008.11.29

Date

SPEED DOME CAMERA

User’s Manual

SPEED DOME CAMERA

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Radio Shack Radio 22CH GMRS FRS User Guide
Radio Shack TV Antenna 15 1867 User Guide
RCA Flat Panel Television 37LA30RQ User Guide
Remington Hair Clippers SCC 100R User Guide
Rogue Audio Stereo Amplifier TEMPEST II User Guide
Samsung Clothes Dryer DV520 User Guide
Samsung Digital Camera Digimax 200 User Guide
Sanyo CRT Television DS13390, DS19390, DS25390 User Guide
Sanyo Security Camera VCC MC500P User Guide
Sears Lawn Mower 91725004 User Guide