FormsMaster 8000se
Series
Operator’s Manual
©Printek, Inc. 2003
1517 Townline Road
Benton Harbor, MI 49022
269-925-3200
Download from Www.Somanuals.com. All Manuals Search And Download.
This equipment has been tested and found to comply with the limits for a Class A
Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference in which case the user will be
required to correct the interference at his own expense.
The user is cautioned that any changes or modifications not expressly approved by
the party responsible for compliance could void the user's authority to operate the
equipment.
This digital apparatus does not exceed the Class A limits for radio noise emissions as
set out by the ICES-003 standard, of the Canadian Department of Communications.
Cet appareil numérique n’émet pas de bruits radioélectroiques depassant les limites
de Classe A prescrites dans la norme NMB-003 Édictée par le Ministre des
Communications du Canada.
Acknowledgments:
IBM and Proprinter are registered trademarks of International Business Machines
Co.; DEC is a registered trademark of Digital Equipment Corporation; Epson is a
registered trademark of Seiko Epson; QMS is a registered trademark of Quality Micro
Systems, Inc.; IGP is a registered trademark of Printronix Corp.; Printek is a registered
trademark of Printek, Inc.
Specifications are subject to change without notice.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Read all setup and operating instructions before
proceeding with operation.
Operate printer only on a firm, solid surface.
Do not operate in an enclosure unless properly ventilated. Make sure no
ventilation openings are blocked or obstructed, which may result in the
printer overheating.
Do not operate near a heat source.
No user-serviceable parts inside. Refer service or repairs
to a qualified service professional.
Use of genuine Printek replacement parts is required to warrant proper,
safe operation.
Any alteration or modification of this device voids the user warranty and
may make the product unsafe to operate.
The printhead and motors get hot during use. Wait until they cool before
touching them.
Make certain the printer is disconnected from AC power before removing
any covers or performing any required cleaning or maintenance.
Connecting this printer to an ungrounded receptacle can result in electrical
shock.
Never place the printer near inflammable or explosive substances. Do not
operate near liquid or spill liquid into the printer at any time.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Lesen Sie vor der Inbetriebnahme die Aufbau- und
Bedienungsanleitung.
Der Drucker muss zum Betrieb auf einer festen, soliden Oberfläche stehen.
Betreiben Sie den Drucker nicht in einem kleinen, geschlossenen Raum, es
sei denn dieser wird ordnungsgemäß belüftet. Achten Sie darauf, dass die
Lüftungen nicht blockiert oder versperrt sind, denn dies kann zum
Überhitzen des Druckers führen.
Nehmen Sie den Drucker nicht in der Nähe einer Wärmequelle in Betrieb.
Enthält keine Teile, die vom Bediener instandgesetzt
werden können. Bitte wenden Sie sich bei Instandsetzung oder Reparatur
an qualifiziertes Kundendienstpersonal.
Die Verwendung von echten Printek Ersatzteilen ist notwendig, um
ordnungsgemäßen, sicheren Betrieb zu gewährleisten.
Änderungen oder Modifikationen dieses Geräts machen die Garantie
ungültig und können den sicheren Betrieb des Produkts gefährden.
Während des Druckens werden Druckerkopf und Motoren heiß. Warten
Sie, bis sich die Teile abgekühlt haben, bevor Sie sie berühren.
Vergewissern Sie sich, dass der Drucker nicht mehr an die Stromquelle
angeschlossen ist, bevor Sie Abdeckungen abnehmen oder das Gerät
reinigen bzw. warten.
Schließen Sie diesen Drucker nicht an eine ungeerdete Steckdose an; dies
kann zum Elektroschock führen.
Setzen Sie den Drucker niemals in die Nähe von feuer- oder
explosionsgefährlichen Stoffen. Betreiben Sie den Drucker nicht in der
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Nähe von Flüssigkeiten und lassen Sie keine Flüssigkeiten in den Drucker
gelangen.
TABLE OF CONTENTS
INTRODUCTION
Models and Options
Manual Contents
1
1
2
GETTING STARTED
Installation
5
5
Interface Set Up
6
7
8
9
9
RS-232C Serial Interface
Parallel Interface
Ethernet 10/100BaseT
Wireless Ethernet Print Server
Installing the Ribbon Cartridge
Why Use Only Printek® Brand Ribbons
Ribbon Installation
10
10
12
Loading Paper
15
15
16
FormsMaster 8000se Single Tractor Model
FormsMaster 8003se TriTrak™ Model
Printer Self-Test
19
DAILY OPERATION
Introduction
21
21
Control Panel Features
LCD Display and Online Indicator
Control Panel Buttons
22
22
24
Selecting and Loading Forms
27
27
27
Selecting a Form Already Loaded in the Tractors
Loading a New or Different Form In the Tractors
Ejecting And Tearing Off A Form
32
Installing a New Ribbon Cartridge
Removing the Old Ribbon Cartridge
Installing the New Ribbon Cartridge.
34
34
35
Aligning Print
36
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Error Conditions
Check Paper
38
38
39
39
39
39
40
40
40
40
No Paper to Load
Too Much Paper to Unload
Selected Form is Not Loaded
No Ribbon or Wrong Ribbon
Ribbon Lid Open
Paper Door Open
Change Ribbon
Other Errors
PRINTER CONFIGURATION
41
Introduction To Setup
Setup Buttons
41
41
42
42
42
43
43
Entering Setup
Using the MENU Button
Using the SUBMENU Button
Using the ITEM and VALUE Buttons
Exiting Setup
Forms Menu
44
45
Forms Menu Items
Interface Menu
51
51
52
57
Entering the Interface Menu
RS-232C Serial Interface Items
Parallel/LAN Interface Items
Options Menu
ImagerPlus Graphic Card
Test Menu
60
65
69
FORM CONSTRUCTION
Form Construction
Form Layout Considerations
73
73
74
MAINTENANCE AND TROUBLESHOOTING
Error Messages
Preventive Maintenance
75
75
76
76
Obtaining Service
ADVANCED SETUP FEATURES
Security Menu
79
79
USING REMOTE SETUP
83
83
83
Remote Setup via Windows Application
Remote Setup via Generic Text File
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE OPTIONAL SETUP MODULE
Introduction
91
91
Setup Module Installation
91
PRINTER RESET CONDITIONS
95
CONTROL CODE AND ESCAPE SEQUENCE
SUMMARIES
97
97
98
Genicom 3840 and 3410 Emulation
ANSI x3.64 Emulation
Epson FX Emulation
IBM Proprinter Emulation
LA-120/210 EMULATION
Simple TTY Emulation
Printek Emulation
99
101
102
103
104
ASCII CHARACTER TABLES
SPECIFICATIONS
105
111
117
GLOSSARY OF TERMS
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Thank you for purchasing a Printek FormsMaster 8000se Series
Printer. This printer has been designed to provide years of service handling
your most demanding printing requirements.
The FormsMaster 8000se Series printers offer higher throughput than all
other printers in its class. In addition, an easy to use front panel combined
with the ability to store ten different form configurations makes handling
multiple forms as simple as a button press for the operator.
Models and Options
The FormsMaster 8000se and the FormsMaster 8003se differ only in the
number of tractor paths available, one path or three.
Options available for both models include:
·
·
·
·
·
·
·
Ethernet 10/100BaseT Print Server
Wireless Ethernet Print Server
Imager Bar Code Co-processor
ImagerPlus Bar Code Co-processor
Print Stand (required for reduced sound levels)
Internal FormsCutter
Setup Module
1
Download from Www.Somanuals.com. All Manuals Search And Download.
I N T R O D U C T I O N
Manual Contents
*Unless specifically noted, all instructions and information herein is
valid for all models in the 8000se series.
·
GETTING STARTED provides instructions for installation, setting up
the computer interface, installing the ribbon cartridge, loading paper,
and performing a printer self-test.
·
DAILY OPERATION provides more detailed descriptions of the
features that are used most frequently. These include the “every day”
buttons and indicators on the control panel, selecting or loading new
forms, ejecting forms, changing the ribbon cartridge, aligning print with
preprinted forms, and causes for common error conditions.
·
PRINTER CONFIGURATION provides detailed information on how
to use Setup to permanently store parameters for each of the ten
forms, parameters for the standard and optional interfaces, and
parameters for other options.
·
·
SPECIFYING FORMS provides tips for form construction and layout.
MAINTENANCE AND TROUBLESHOOTING lists more serious
error messages than discussed in the Daily Operation section,
preventive maintenance, and how to obtain service.
·
·
·
ADVANCED SETUP FEATURES provides information on how to set
menu security.
USING REMOTE SETUP describes how to “set up” default
parameters from a host computer.
USING THE SETUP MODULE describes how the optional Setup
Module can be used to copy Setup parameters from one printer to
another.
·
·
PRINTER RESET CONDITIONS describes the state of the printer
after power up or reset.
CONTROL CODE AND ESCAPE SEQUENCE SUMMARIES lists
the commands supported for each printer emulation.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
·
ASCII CHARACTER TABLES show the characters for each
character set.
·
·
SPECIFICATIONS lists the operating ranges and ratings of the printer.
GLOSSARY OF TERMS provides definitions for terms used in this
manual.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
This chapter will use the fewest possible steps to get the first time user up
and running quickly. You will be guided through the following steps:
·
·
·
·
·
Finding a suitable location and installing the printer
Setting up a host interface if necessary
Installing the ribbon cartridge
Loading paper
Performing a printer self-test
Installation
Before installation, a suitable site must be chosen. Suitable sites include
offices, computer rooms, and most factory environments. The Printek
FormsMaster printers have been designed to be rugged, heavy duty
printers. As such, they will handle most harsh environments, but should not
be placed in direct sunlight or in areas that will exceed the rated
temperature, humidity, or power requirements. For details, refer to
“SPECIFICATIONS” on page 111.
Once a site has been selected, the printer should be placed on a Printek
Print Stand. The Printek print stand is especially recommended for the
FormsMaster 8003se and is required to meet the low noise rating of the
printer. Of course, another sturdy print stand or table with a slotted top for
feeding paper into the bottom of printer may be used.
The print stand should be located in an area large enough to provide easy
access to both the front of the printer and the rear for accessing printed
output. Unpack the printer as described in the “FormsMaster 8000se
Unpacking Instructions” and place the printer on the print stand.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D
Note: Placing the printer on the print stand is best accomplished
with two people. Proper lifting technique should be observed.
Caution: Before connecting or turning on power, make sure that all
shipping materials have been removed. These materials include
a cardboard brace with a foam insert that secures the print head
(open the ribbon lid to access), a cardboard brace placed at the
rear of the printer and a cardboard brace placed over the
tractor shuttle in the 8003se (open the paper door on the front
of the unit to access).
Refer to UNPACKING
INSTRUCTION in the box for more details.
Next, connect the power cord supplied with the printer to the printer and an
appropriate power outlet. Now connect the computer cable(s) to the
appropriate interface. The picture below shows the location of the standard
Parallel and RS-232C interface connectors on the rear panel of the printer.
PARALLEL I/O
SERIAL I/O
Interface Connectors on Rear of Printer
Interface Set Up
Depending upon which interface is being used to connect the printer to the
host computer, some set up may or may not be required. This is true of the
6
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D
standard parallel or serial ports and any optional interface that may be
installed.
The factory default settings for each interface should work well for most
installations. However, the following paragraphs provide some basic
information about each interface and also refer to the page number in the
Configuration chapter where all the details for each interface are described.
If you need to make changes to the default settings, please refer to
“Introduction to Setup” on page 41 for instructions on how to access the
printer’s Setup menus.
Once you are comfortable that the interface settings match those required
by your computer, proceed to the next section, “Installing the Ribbon
Cartridge” on page 10.
RS-232C Serial Interface
This interface uses a 25 pin “D” connector as described below. The default
settings are 9600 baud, 8 data bits, 1 stop bit, and no parity with hardware
handshake on pin 11. The default printer emulation is Epson. For a
complete description of all the default settings for this interface, refer to
page 52.
Pin Signal
1
2
3
4
5
6
7
8
Chassis ground.
Transmit data. (Printer output).
Receive data. (Printer input).
Request to send (set). (Printer output).
Clear to send (ignored). (Printer input).
Data set ready (ignored). (Printer input).
Signal ground.
Carrier detect (ignored). (Printer input).
11 Printer busy. (Printer output).
20 Data terminal ready. (Printer output).
RS-232C Serial Interface Connector
7
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D
Parallel Interface
This interface uses the standard 36 pin parallel connector as shown below.
The default printer emulation is Epson. For a complete description of all the
default settings for this interface, refer to page 57.
Pin Signal
Pin Signal
____________________
_______________________
1 DATA STROBE
19 DATA STROBE RTN
10 ACKNOWLEDGE
28 ACKNLG RETURN
2 DATA 1
11 BUSY
20 DATA 1 RETURN
29 BUSY RETURN
3 DATA 2
12 PAPER ERROR
21 DATA 2 RETURN
13 SELECT
________________
4 DATA 3
22 DATA 3 RETURN
14 AUTO FEED
16 ±0V
5 DATA 4
23 DATA 4 RETURN
17 CHASSIS GROUND
6 DATA 5
24 DATA 5 RETURN
18 +5V at 200mA Max.
______
31 INIT
7 DATA 6
25 DATA 6 RETURN
30 INIT RTN
_________
32 FAULT
8 DATA 7
26 DATA 7 RETURN
35 +5V LOGIC HIGH
______________
9 DATA 8
36 SELECT IN
27 DATA 8 RETURN
Parallel Interface Connector
8
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D
Ethernet 10/100BaseT
This interface uses a standard RJ-45 connector and the default printer
emulation is Epson. For a complete description of all the default settings for
this interface, refer to Parallel/LAN Interface Items on page 57. For
additional software installation and operational information, please refer to
the Troy XCD Quick Install Manual shipped with the unit
Wireless Ethernet Print Server
This interface is intended to be used for 802.11b wireless connectivity. It
may also be used with conventional CAT-5 twisted pair wiring, using the
standard RJ-45 connector. The interface automatically senses when a
CAT-5 connection is present and will disable the wireless capability.
For additional software installation and operational information, please refer
to the Printek Wireless Ethernet Print Server Manual shipped with the unit.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D
Installing the Ribbon Cartridge
The Printek FormsMaster printer has been designed to make installing
Printek brand ribbons a simple, clean process. Unlike other printers, there
is no need to touch the ribbon fabric or deal with difficult to position ribbon
guides. The following sections explain why the use of Printek brand ribbons
should be important to you and will guide you through installing the ribbon
cartridge.
Why Use Only Printek® Brand Ribbons
REORDER NUMBER 90729
FOR NEAREST DISTRIBUTOR
CALL 1-800-368-4636
Printek® Brand Ribbon Label
Printek brand ribbons can be identified by the above label on each ribbon.
There are many reasons to use only Printek brand ribbons in your
FormsMaster 8000se series printer. First of all, using only Printek
brand ribbons will automatically extend the print head warranty to
two years.
The reason this is possible is that Printek brand ribbons are manufactured to
much higher quality standards than those offered by other manufacturers.
This provides not only longer print head life, but also longer ribbon life… 23
million characters as compared to only 15 million characters from some
generic ribbons.
Remember that using only Printek brand ribbons is important because the
wear that is started and the contamination that remains from even one
inferior ribbon will continue to damage the print head. Also, damage to
other printer components which is caused by the use of non-Printek ribbons
will not be covered by the printer’s warranty.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D
Using inferior ribbons would be like using poor quality fuel in your
automobile. Premature engine failure and poor performance leading up to
the failure would be the best you could expect.
Other useful features available only with the use of Printek brand ribbons
are that the printer will not allow printing if a ribbon is not installed, and the
printer will alert the operator when a ribbon needs to be changed.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D
Ribbon Installation
1. Open the ribbon lid on top of the printer and position the print head
for ribbon loading by lifting the ribbon loading handle as indicated in
the following picture.
Opening the Ribbon Loading Handle
2. Remove the new ribbon from its plastic bag and make sure the
ribbon fabric is taut by turning the knob on top of the ribbon
cartridge in a counterclockwise direction as indicated by the arrow
on the cartridge.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D
3. With the right hand end of the ribbon tilted down, insert the tab on
the end of the cartridge into the opening in the ribbon tray.
Installing the Ribbon Cartridge
4. Now lower the left end of the cartridge down while guiding the
ribbon fabric between the nose of the print head and the ribbon guide
pins. Continue to lower the cartridge until the tab on the left end of
the cartridge snaps into place.
Ribbon Guided Between the Print Head
and Guide Pins
13
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D
5. Finally, lower the ribbon loading handle to its original position.
Closing the Ribbon Load Handle
6. Close the ribbon lid on top of the printer.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D
Loading Paper
When shipped from the factory, the basic configuration for all ten forms is
an eleven inch form, six lines per inch, and ten characters per inch. If the
forms you are loading do not match these requirements, please refer to the
“PRINTER CONFIGURATION” chapter on page 41 and review the
“Introduction to Setup” and “Forms Menu” sections.
Please refer to the appropriate section below for loading paper in the
FormsMaster 8000se or FormsMaster 8003se.
FormsMaster 8000se Single Tractor Model
1. Make sure the printer is powered on and that the printer is off line
(ONLINE indicator flashing red).
2. Lift open the paper door on the front of the printer to expose the
paper feed tractors as shown below.
FormsMaster 8000se Tractors
3. Open the doors on each tractor.
4. Feed the paper up through the bottom of the printer and position the
holes in the edge of the paper over the pins in the left tractor while
15
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D
making sure that the paper will not extend above the top of the
tractors. Then close the tractor door.
Note: The left tractor position is not adjustable. If it is necessary
to adjust where printing begins, refer to “Aligning Print”
in the “Daily Operation” section of this manual.
5. Now position the paper in the right tractor in the same fashion. If
necessary, the position of the right tractor may be adjusted. To do
so, move the lever on the side of the tractor down to unlock the
tractor and slide the tractor sideways on the shafts. If necessary, the
paper guides between the tractors may be slid in either direction to
accommodate the form width. Make sure that the guides are spaced
evenly between the tractors.
After the paper is placed in the tractor and the door is closed,
position the tractor far enough to the right so that there is no buckle in
the paper between the tractors, but not so tight that the holes in the
paper are distorted. Lock the tractor in place by returning the lever
to the up position.
6. Close the paper door.
7. Press the LOAD button.
8. Place the printer on line by pressing the ONLINE button.
FormsMaster 8003se TriTrak™ Model
The following instructions will guide you through loading all three tractor
paths.
1. Make sure the printer is powered on and that the printer is off line
(ONLINE indicator flashing red).
2. Press the UNLOAD button to move the tractor shuttle forward to the
load position.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D
3. Lift open the paper door on the front of the printer to expose the
paper feed tractors as shown in the following picture.
FormsMaster 8003se Tractors
Loading the Front Tractors
4. Open the doors on each tractor.
5. Feed the paper up through the bottom of the printer and position the
holes in the edge of the paper over the pins in the left tractor while
making sure that the paper will not extend above the top of the
tractors. Then close the tractor door.
Note: The left tractor position is not adjustable. If it is necessary
to adjust where printing begins, refer to “Aligning Print”
in the “DAILY OPERATION” section of this manual.
6. Now position the paper in the right tractor in the same fashion. If
necessary, the position of the right tractor may be adjusted. To do
so, move the lever on the side of the tractor down to unlock the
tractor and slide the tractor sideways on the shafts. If necessary, the
paper guides between the tractors may be slid in either direction to
accommodate the form width. Make sure that the guides are spaced
evenly between the tractors.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D
After the paper is placed in the tractor and the tractor door is closed,
position the tractor far enough to the right so that there is no buckle in
the paper between the tractors, but not so tight that the holes in the
paper are distorted. Lock the tractor in place by returning the lever
to the up position.
Loading the Center Tractors
7. Tilt the front tractors forward by pulling the green lever on the right
hand side of the front tractor assembly forward.
8. Repeat steps 4 through 6 above.
Front Tractors Tilted Forward for Access to Center Tractors
Loading the Rear Tractors
9. Tilt the center tractors forward by pulling the green lever on the
center tractor assembly forward.
10. Repeat steps 4 through 6 above.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D
Selecting Which Form to Print
11. Close the paper door.
12. Press the FORM SELECT button until the desired form is displayed
and then press the LOAD button. The printer will now move the
selected form into position for printing.
13. Place the printer on line by pressing the ONLINE button.
Printer Self-Test
The printer performs many self diagnostics each time power is turned on. If
you wish to perform an actual printing test, use the following steps.
1. Make sure the printer is powered on with ribbon and paper loaded.
2. Take the printer off line (the ONLINE indicator will be flashing red).
3. Press the SETUP/MENU button four times to display TESTMENU
on the front panel.
4. Press either of the ITEM buttons until TestModeis displayed on the
top line.
5. Press either of the VALUE buttons until BarberPoleis displayed on
the bottom line.
6. Press the ONLINE button.
7. The printer will now exit Setup and begin printing a rotating character
pattern. To stop or restart printing the test pattern, press the ONLINE
button.
8. To take the printer out of the test mode, stop the test by pressing the
ONLINE button.
9. Press the SETUP/MENU button four times to display TESTMENU.
10. Press either of the ITEM buttons until Test Modeis displayed on the
top line.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
G E T T I N G S T A R T E D
11. Press either of the VALUE buttons until Off is displayed on the
bottom line.
12. Press the ONLINE button.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
DAILY OPERATION
Introduction
This chapter describes how to use the “everyday” features of the
FormsMaster 8000se. The items covered are:
Control Panel Features – describes the most commonly used
features of the printer’s control panel.
Selecting and Loading Forms – describes how to insert paper
or forms into the tractors and how to inform the
printer of which forms are “loaded”.
Ejecting and Tearing Off a Form – describes how to remove
printed documents from the printer.
Installing
a
New Ribbon Cartridge – describes first time
installation of the ribbon cartridge.
Aligning Print – describes how to precisely align where data is
printed on a form.
Common Error Conditions – describes errors that may occur
during normal printing operations.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
Control Panel Features
The following picture shows the printer’s control panel. The control panel
consists of a two line LCD display, an ONLINE status indicator, nine push
button switches or “buttons”, and a speaker. Each of these items is
described below
FORM
SELEC
T
FOR
M
FEED
MENU
ITEM
SETU
ON
LI
LCD
DISPLAY
ALIGN
PRINT
SUB-
MENU
VALUE
Control Panel
LCD Display and Online Indicator
LCD Display
This two line by sixteen character display is used
to convey several types of information. When the
printer is on line and printing, or ready to print,
the display will show the currently selected
tractor path and the form currently loaded in that
path. When the printer is off line, the display will
continue to show this information, additional
information based upon other buttons being
pressed by the operator, or error conditions such
as “Check Paper”.
ONLINE Status
This is a multicolored LED which is used to
display the following information:
Indicator LED
Green:
The printer is on line and ready to print.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
Flashing Green:
Flashing Red:
The printer is in the process of going back on
line. Typically occurs after a new form has been
loaded while the printer is confirming which forms
are loaded in the tractors.
The printer is currently off line and cannot print.
This may be due to the operator taking the printer
off line or the printer may have detected an error
condition, such as running out of paper, which
requires operator intervention. If due to an error
condition, the cause of the error will periodically
be shown on the LCD display. After the cause
of an error condition has been resolved, press the
ONLINE button to clear the error. This will also
place the printer back on line and allow printing
to resume.
Yellow:
The printer is in the process of exiting the Setup
mode and saving Setup values, or the printer is
currently busy performing an operation with the
optional Setup Module.
Flashing Yellow:
The user has pressed the SETUP button and
entered the Setup mode (may be exited by
pressing the ONLINE button after the desired
changes have been made). For more
information, see the chapter on “Printer
Configuration”.
Audible Alarm:
This device produces various tones to alert the
operator when different error conditions occur.
It may also be used to produce a tone when a
bell character (ASCII BEL) is received from a
host computer.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
Control Panel Buttons
ONLINE
This button toggles the printer between the on line
and off line state. When the printer is on line, it
may be printing or may begin printing at any time.
To stop the printing or prevent printing from
starting, use this button to take the printer off line
(see “ONLINE Status Indicator” above). The
printer must be off line in order to use the other
control panel buttons.
This button is also used to place the printer back
on line following any error condition (ONLINE
indicator is flashing Red), such as paper out.
When pressed to go on line, the printer will first
attempt to clear any errors. For example, if there
is a paper out condition, the printer will attempt
to load the form in the currently selected tractors
and, if successful, go on line.
FORM FEED/LOAD
This button performs a number of different form
feeding functions. The printer will automatically
select the correct function to perform based upon
the current position of the form.
LOAD:
·
Loads the form that has been selected with
the FORM SELECT button.
If a the selected form is already recognized
as “loaded” in the tractors, the printer will
position the tractors if necessary
(FormsMaster 8003se) and advance the
form to the print position.
If the selected form is not currently
considered to be loaded in the tractors
(display shows <Not Loaded>),this button
will change the status of this form to “loaded”
24
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
and the bottom line of the display will show
the path(s).
FORM FEED:
·
If a form is currently loaded and perhaps
partially printed, this button will advance the
bottom of the current form to the tear bar so
that it may be torn off.
·
If a form has already been advanced to the
tear bar, this button will advance the next
form to the tear bar.
FORM SELECT
/UNLOAD
This button is used to access up to ten different
forms which have been previously configured
with the Setup menus (see the chapter on Printer
Configuration for more information).
When this button is pressed, one of two functions
will be performed.
UNLOAD:
·
If a form is currently in position to be
printed, this button will pull the form down
until the top of the form is below the top of
the tractors. In the FormsMaster 8003se
this will also cause the tractor shuttle to
move forward for easy access to all tractors.
FORM SELECT:
·
If the form has already been pulled down to
the tractors as described above, this button
will cycle through all the available form
choices. Forms which are not considered to
be “loaded” in the tractors will flash <not
loaded>on the bottom line of the display.
In the FormsMaster 8003se the not loaded
message will alternate with the tractor path
assigned to that form. For more information,
see the following section on “Selecting and
25
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
Loading Forms”.
ALIGN PRINT
This button will access the horizontal and vertical
print adjustment settings for the currently selected
form.
When ALIGN PRINT is pressed, the horizontal
adjustment is shown first. Pressing the VALUE
buttons will move the print position on the line left
or right by 0.01 inches for each press of a button
as indicated on the display. The arrows to the
side of the number will indicate the direction the
print will be moved.
To access the vertical adjustment, press either
ITEM button. Pressing the VALUE buttons will
now move the print up or down on the page by
0.01 inches for each press of a button as
indicated on the display. The arrow to the right
of the number will indicate the direction the print
will be moved.
For a more detailed description, see “Aligning
Print” later in this chapter.
SETUP
This button is used to set up the various operating
parameters of the printer for forms, interfaces,
etc. This button is not used on a daily basis. For
more information see the chapter on “PRINTER
CONFIGURATION”.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
Selecting and Loading Forms
Note: A form is not considered “loaded” by merely placing the
form in the tractors. To prevent printing on the wrong
form, the printer must be made aware of what form(s)
are currently loaded. When a new form is placed in the
tractors, the form must be “loaded” using the control
panel as described in the next section, “Loading a New
or Different Form in the Tractors”.
Selecting a Form Already Loaded in the Tractors
To select a form that is already loaded in the tractors, take the printer off
line and press the FORM SELECT button until that form is displayed (a form
that is not considered to be loaded will flash <Not Loaded>on the
bottom line of the display). The form selection will be displayed as FORM
0through FORM 9or as the actual name of the form if that has been set
up.
To position the form for printing, you may press the FORM FEED button
which will position the form, or you may press the ONLINE button which will
both position the form and place the printer on line.
Loading a New or Different Form In the Tractors
This section describes how to “load” a form in the tractors. This involves
physically placing the paper or form in the tractor mechanism and then
informing the printer that the new form is present.
Select the Form to be Loaded
1. Take the printer off line by pressing the ONLINE button. The ONLINE
indicator should now be flashing red.
2. Press the FORM SELECT/UNLOAD button. This will move the current
form from the print position down to the tractors for removal. In the
27
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
case of the FormsMaster 8003se this will also move the shuttle
forward for easy access to all tractor paths.
3. Continue to press the FORM SELECT button until the desired form
name is shown on the top line of the display. The form name will be
FORM 0 through FORM 9 or the actual name of the form if the
name has been set in Setup. If the desired form is not considered to
be “loaded” by the printer, <Not Loaded> will flash on the
bottom line of the display. In the case of the FormsMaster 8003se
the not loaded message will alternate with the path(s) that this form is
to be loaded in.
Loading the Form in the Tractors
4. Open the paper door on the front of the printer. This will provide
access to the tractors as shown below. If your printer is a
FormsMaster 8000se, only one set of tractors will be available and
you may skip ahead to step 6.
FormsMaster 8003se tractors
5. Depending upon which path(s) the new form is to be placed in, you
may need to tilt the front and/or center tractors forward as shown.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
FormsMaster 8003se with front and center
tractors tilted forward.
6. Open the tractor doors and remove the old form.
FormsMaster 8003se with rear path empty
7. If the new form is a different width than the previous form, unlock the
right tractor and move it to approximately the new position. Note
that the left tractor position is fixed and may not be moved.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
8. Place the left edge of the new form in the left tractor with the holes
aligned with tractor pins. Make sure that the top edge of the form
does not extend above the top of the tractors.
Paper positioned in left tractor.
9. Close the left tractor door.
10. Now position the paper in the right tractor in the same fashion. If
necessary, the position of the right tractor may be adjusted. To do
so, move the lever on the side of the tractor down to unlock the
tractor and slide the tractor sideways on the shafts. If necessary, the
paper guides between the tractors may be slid in either direction to
accommodate the form width. Make sure that the guides are spaced
evenly between the tractors.
After the paper is placed in the tractor and the door is closed,
position the tractor far enough to the right so that there is no buckle in
the paper between the tractors, but not so tight that the holes in the
paper are distorted. Lock the tractor in place by returning the lever
to the up position.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
New form loaded in tractors
Informing the Printer That the New Form is Loaded
11. Press the LOAD button. The display will now show that the new form
has been “loaded”.
12. If your printer is a FormsMaster 8003se you may repeat the above
steps to load additional forms at this time.
13. Close the paper door.
14. Make sure the correct form to be positioned for printing is selected
and press either the LOAD button or the ONLINE button. The LOAD
button will position the form for printing but will not place the printer
on line. The ONLINE button will both position the form and place the
printer on line. Note that the first time the printer is placed on line
after a new form is loaded, the form(s) currently known to be loaded
by the printer will scroll across the display as the printer goes on line.
The operator should observe the forms displayed to confirm that the
correct forms are recognized as loaded.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
Ejecting And Tearing Off A Form
When most print jobs complete, they will command the paper to be
positioned at the top of the next form so that the printer is ready for the next
job. This is, however, dependent solely upon how the programmer chose
to write your particular application software. If your software does position
the paper at the top of the next form, the printer will automatically position
the form at the tear bar as shown in the following picture.
Bottom of form at tear bar
If your form is positioned as shown, you may skip the next section on
positioning and proceed with “Tearing off a Form”.
Positioning the Form for Tear Off
1. If your print job has completed and the form is not positioned as
shown above, take the printer off line by pressing the ONLINE button
(indicator will change from green to flashing red).
2. Press the FORM FEED button. This will automatically position the
form at the tear bar and you may tear off the form as described
below.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
Tearing off a Form
1. Make sure the printer is off line (indicator flashes red when off line)
by pressing the ONLINE button if necessary. This will prevent the
printer from pulling the paper down to start printing the next job while
you are tearing off this one.
2. Pull the paper toward the front of the printer and toward one side of
the printer as shown.
Tearing off a form
3. Place the printer back on line with the ONLINE button (indicator
changes to green). The form will automatically be pulled down into
position for printing the next time the printer receives data to be
printed.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
Installing a New Ribbon Cartridge
Removing the Old Ribbon Cartridge
1. Open the ribbon lid on top of the printer and position the print head
for ribbon loading by lifting the ribbon loading handle as indicated in
the following picture.
Opening the Ribbon Loading Handle
34
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
2. Grasp the left end of the ribbon cartridge and lift it up and toward the
rear of the printer as shown below.
Removing the Old Ribbon Cartridge
3. Lift the right end of the ribbon and remove the ribbon from the
printer.
Installing the New Ribbon Cartridge.
Note: The use of Printek brand ribbons is recommended for increased
ribbon life and print head life. The use of only Printek brand
ribbons is required for the extended print head warranty. For
details, see “Why Use Only Printek Brand Ribbons” in the
“GETTING STARTED” chapter.
4. Remove the new ribbon from its plastic bag and make sure the
ribbon fabric is taut by turning the knob on top of the ribbon
cartridge in a counterclockwise direction as indicated by the arrow
on the cartridge.
5. Install the new ribbon by reversing the above removal process. For
a more detailed installation description, see “Installing the Ribbon
Cartridge” on page 10.
6. Close the ribbon lid and place printer back on line.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
Aligning Print
When a new form is loaded into the printer for the first time, it may be
necessary to adjust where printing begins. This depends upon how the
software that controls the printing was written. If the software was written
to perform its own character and line spacing relative to the edges of the
form, then adjustment may not be necessary. If the print position needs to
be adjusted, the following discussion will describe how this is accomplished.
Note that the alignment for the selected form is permanently stored in the
printer’s memory and does not have to be readjusted each time the form is
loaded.
To align print on a particular form, select that form with the FORM SELECT
button and then press the ALIGN PRINT button. If the form selected is
named “Invoices”, the display would now show the following.
Aligning Print
On INVOICES
After a short time, the display would change to show that you can now
MOVE PRINT left or right. Be sure to remember that you are moving
where the print is placed on the page.
MOVE
Left/Right
PRINT
¬0.00”®
The VALUE buttons will move the print left or right in 1/100th inch
increments. Note that the left and right arrows will change according to
which way the print has been moved from the normal print position. The
maximum distance print may be moved is 9.99 inches in either direction.
To move the print vertically on the page, press either of the ITEM buttons
and the display will change to the following.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
MOVE
Down/Up
PRINT 0.00”
×
The VALUE buttons will move the print down or up in 1/100th inch
increments. Note again that the arrow will change according to the
direction the print is to be moved from the normal print position. The
maximum distance print may be moved is 9.99 inches in either direction.
Example
In this example, a number needs to be printed in a box on a preprinted
form. This form could be a packing list, an invoice, or a check. The first
time the page is printed, the number misses the box as shown below.
12345
In this case, the print needs to be moved to the right and down. To
accomplish this, press ALIGN PRINT and access the Left/Rightoption.
First move the print to the right using the VALUE buttons. It appears that
the text needs to move about three characters. If the text is being printed at
10 cpi (characters per inch), this would be 0.30 inches. After making this
adjustment the display would look as follows.
MOVE
Left/Right
PRINT
¾0.30”®
If you were to print this form now, it would appear as follows, showing that
the print still needs to be moved down.
12345
To move the print down, access the Down/Upoption by pressing either of
the ITEM buttons. It appears that the print needs to be moved down nearly
the height of the characters. These characters are approximately 0.10
inches tall, so move the print down about 0.08 inches. The display should
look as follows.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
MOVE
Down/Up
PRINT
0.08”
¯
Now when the form is printed again, the text will be printed in the box as
shown here.
12345
Common Error Conditions
Whenever the printer detects an error condition, it will automatically go off
line. User correctable errors are “flashed” on the display. These errors can
typically be recovered from without loss of data and are listed in this section
of the manual.
Other errors which typically result in loss of data are considered fatal errors.
These errors display the word ERROR on the top line of the display and do
not flash. These errors are listed in the “Troubleshooting” section of this
manual.
Check Paper
This error is caused either by running out of paper or by a paper jam. The
printer will attempt to determine the cause of a paper problem and
accompany the “Check Paper” message with “Paper Out”,
“Paper Jam”, or “Paper Out/Jam”.
It is not necessary to press the UNLOAD button. If your printer is a
FormsMaster 8003se, you may access the tractor path with the error by
simply tilting any tractors in front of that path forward (see “Loading the
Center Tractors” on page 18).
If the error is caused by a paper jam, remove the jammed form. If the form
remaining in the tractors has tears along the top edge, remove it from the
tractors, tear it off, and place the next form in the tractors.
If the error is caused by running out of paper, simply place a new box in the
print stand and place the first form in the tractors.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
Finally, place the printer back on line by pressing the ONLINE button.
This will automatically load the new form and begin printing. Depending
upon how the printer has been set up, the printer may start printing where it
left off or it may start at the beginning of the page where the error occurred
and reprint the entire page. See “Paper Out Fault Action” on page 61 for
more information.
No Paper to Load
This error occurs when the LOAD button has been pressed and there is no
paper or form in the tractors. Place paper in the tractors and press LOAD
again.
Too Much Paper to Unload
This error occurs when the UNLOAD button has been pressed and there is
paper present too far beyond the tear bar. This error serves as a warning
that you may be putting forms that have already been printed on back into
the printer. Tear off any printed forms past the tear bar and press UNLOAD
again. This error also occurs if the LOAD button has been pressed and the
current form cannot be unloaded.
Selected Form is Not Loaded
This error occurs when ONLINE has been pressed and the currently selected
form is displaying <Not Loaded>. Either press LOAD to load the
selected form or select a different form and then press ONLINE.
No Ribbon or Wrong Ribbon
This error occurs when the printer is attempting to go on line and cannot
detect the presence of a ribbon cartridge. This may be due to the ribbon
not actually being present in the printer, or the ribbon may not be installed
properly.
This error may also occur when attempting to use a non-Printek brand
ribbon. Before attempting to use a ribbon brand other than Printek, please
read “Why Use Only Printek® Brand Ribbons” on page 10. Then if you
do decide to use non-Printek brand ribbons, refer to “Ribbon Checking”
on page 64.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
D A I L Y O P E R A T I O N
Ribbon Lid Open
This error occurs when ONLINE has been pressed and the ribbon lid has
been left open. Close the lid and press ONLINE again.
Paper Door Open
This error occurs when ONLINE has been pressed and the paper door has
been left open. Close the door and press ONLINE again.
Change Ribbon
This message is periodically displayed when a ribbon has reached the end
of its useful life and indicates that a new Printek ribbon should be installed.
This error is merely a reminder to change the ribbon and does not force the
printer off line.
Other Errors
If other errors occur, it is possible that they may not be resolved without the
aid of
a
factory trained service technician. Please refer to the
“Maintenance and Troubleshooting” section on page 75.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTER CONFIGURATION
Introduction To Setup
The FormsMaster 8000se series printers feature simple, easy to use menus
for setting the various operating parameters for the printer. The parameters
available in these menus usually only need to be set one time, either when
the printer is first installed or perhaps when a new form is to be used.
These values are stored in nonvolatile memory, which means that they will
remain set even if the printer is turned off. Following this introduction are
complete, detailed descriptions of each menu item.
Setup Buttons
For your convenience, the SETUP button and the other buttons used while
in the Setup mode are labeled in yellow on the control panel. Once in
Setup, these buttons are the MENU, SUBMENU, ITEM, and VALUE buttons.
The ONLINE indicator will flash yellow whenever the printer is in the Setup
mode as a reminder to use the yellow labels. The buttons used for Setup
are shown below.
FORM
SELEC
T
FOR
M
FEED
MENU
ITEM
SETU
ON
L
LCD
DISPLAY
SUB-
MENU
ALIGN
PRINT
VALUE
Control Panel Setup Buttons
While in Setup, the placement of the text on the LCD display indicates
which button or buttons to use to change what is displayed. In nearly all
cases, you should use the button or buttons closest to the item you wish to
change. To change what is on the top line, use the top buttons. To change
what is on the bottom line, use the bottom buttons. To change what is on
the left end of the line, use the left button. To use what is on the right end of
41
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
the line, use the right buttons. Note also that the menu system works on a
“what you see is what you get” basis. This means that whatever value is last
displayed for an item is the value that will be saved when Setup mode is
exited.
Entering Setup
To enter Setup, simply take the printer off line and press the SETUP button.
The ONLINE indicator will begin to flash yellow and the display will
temporarily show the following.
Entering
Setup Menus
After the above message has been shown, the display will change to the first
menu available, which is the FORMS MENUas shown below. In this case
the display will also show the first submenu which will be the form that was
selected when Setup was pressed.
FORMS MENU
Form 0
Using the MENU Button
At this time you may select a different menu by pressing the MENU button
(closest to where FORMS MENUis displayed). Other menus available are
the INTERFACE MENU, the OPTIONS MENU, and the TEST
MENU. This button will also display an option for exiting Setup. If you do
not wish to exit Setup at this time, press the button indicated for Noand
continue to press the MENU button to select the desired menu. The MENU
button may be pressed at any time to select a different menu.
Using the SUBMENU Button
The SUBMENU button selects additional menus that are related to the
selected menu. For instance, if the FORMS MENUhas been selected, the
SUBMENU button (closest to where the form number is displayed) will
42
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
select which form (Form 0through Form 9) is to be set up. Note that
not all menus have submenus. If no submenu is available, the bottom line
will be blank and the SUBMENU button will not be used.
Using the ITEM and VALUE Buttons
Once the correct menu and submenu (if available) is selected, pressing
either of the ITEM buttons will cause the various items and their current
values to be displayed. Note that the items and their values are right
justified and are thus controlled by the buttons to the right of the display.
To scroll through the items available, use the ITEM buttons. To change the
value of the displayed item, use the VALUE buttons to step through the
possible choices. Remember to leave the correct value displayed before
selecting a different item or menu, since “what you see is what you get”
when Setup Mode is exited.
Exiting Setup
Two methods of exiting Setup are available. If you wish to exit Setup and
remain off line, press the MENU button to display the following option.
¬No
Setup
¬Yes
Exit
Menus?
Pressing the button indicated for No will allow you to make additional menu
choices. Pressing the button indicated for Yes will display one of the
following messages depending on whether or not changes were made, reset
the printer if changes were made, and then leave the printer off line.
Exiting Menus
Saving Changes
Exiting Menus
No Changes
43
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
To exit Setup Mode and automatically go on line, press ONLINE. The
display will now show one of the above messages, if changes were made,
and automatically go on line.
Forms Menu
Most form printing applications use several different forms such as packing
lists, bills of lading, invoices, checks, and green bar paper for reports. Not
all of these forms require the same printer settings for things such as font,
character size, line spacing, or form length. The FormsMaster 8000se
series printers store up to ten complete sets of form parameters including
the name of the form. These ten sets of parameters, or “forms”, are
permanently stored in the printer’s memory and are referred to as “Form 0”
through “Form 9”. These forms can be accessed from a single button on
the printer’s control panel or by a command sent from the host computer.
To access the FORMS MENU, enter Setup by pressing the SETUP button.
After the “Entering Setup Menus” message has been displayed, the
following will appear.
FORMS MENU
Form 0
Note that the actual form number will be for the form that was active prior
to entering Setup. To select a different form, press the SUBMENU button
until the desired form is displayed. Next press either of the ITEM buttons to
begin displaying the various items for that form. The items available for
each form are described on the following pages. The factory default values
are indicated with an asterisk (*) in this manual (the asterisk does not
appear on the printer’s display).
44
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Forms Menu Items
Form Name
Form Name
FORM 0
Possible Values: Up to 16 characters of Athrough Z,
Space, 0through 9
When shipped from the factory, the Form Names will be set to “FORM 0”
through “FORM 9”. This name may be changed to any combination of
capital letters (A-Z), numerals (0-9), or spaces. The name may be up to
16 characters in length.
Entering a name uses the SUBMENU and VALUE buttons. The SUBMENU
button will advance the cursor, a flashing block, which is used to indicate
the character that is to be changed. The VALUE buttons will change the
character where the cursor is currently flashing. The order of characters
that may be selected is “ABCDEFGHIJKLMNOPQRSTUVWXYZ, Space,
0123456789”. Even though the name will be right justified while being
entered, it will be automatically centered on the display when not in Setup
Mode, so there is no need to try to center it with spaces.
Tractor Path
Tractor Path
Front
Possible Values: Front, Center, Rear
Center+Rear, Frnt+Cntr+Rear
This item is only available in the FormsMaster 8003se and is used to set the
tractor path to be used for the currently selected form. Typically, most
forms are only loaded in one tractor path and the value will be set to
Front, Center, or Rear.
However, a form can also be set to use multiple paths. This may be
desirable when printing long print jobs where a paper out condition needs to
be avoided. This is often true if the job is to be run overnight or at a remote
and perhaps unattended location. When a form’s tractor path is set to
Center+Rearor Frnt+Cntr+Rear, the printer will automatically switch to
45
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
the next path, or paths, and continue printing until all the specified paths are
empty.
Automatic Cut
Automatic Cut
No
Possible Values: No*,Yes
This item is only available when the optional FormsCutter is installed in the
printer. When set to Yes, the printer will automatically cut each form at the
perforation (based upon the Form Length setting) and eject the form into
the paper basket that is installed with the FormsCutter. If set to No, the
paper will exit through the lower, continuous paper path into the basket on
the print stand. To manually cut a form or report at the end of the current
page, the user can take the printer offline and press the UNLOAD button.
See the FormsMaster 8000se Series FormsCutter Manual for additional
information.
Cut Adjustment
Cut Adjustment
0
Possible Values: Auto, -0.2951” … 0* … +0.2951”,
Auto
This item may be used to adjust the position of the cut relative to the top-of-
form for improved cut accuracy. This item is only available when the
optional FormsCutter is installed. Refer to the FormsCutter manual for
more information.
Lines Per Inch
Lines/Inch
6
Possible Values: 6*, 8
This item sets the line pitch to 6 or 8 Lines Per Inch (LPI).
Form Length
Form Length
66 Lines
46
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Possible Values: 1 … 66* … 227 Lines
This item sets the form length in lines at the current line pitch (LPI). For
example: for an eleven inch form, enter 66 if you are using six lines per inch
or 88 if you are using eight lines per inch.
Top Margin
Top Margin
0 Lines
Possible Values: 0* … 226 Lines
This item sets the top margin in lines. Setting a top margin will reduce the
size of the printable area of the page by the number of lines set. Printing will
not be allowed above the top margin.
Note: In most cases changing where printing begins on a form should
be accomplished with ALIGN PRINT rather than with a top
margin. Adding a top margin may cause some programs to
print the first form correctly and then print following forms too
far down the page if the program sending the data does not
require the margin.
Bottom Margin
Bottom Margin
0 Lines
Possible Values: 0* … 226 Lines
This item sets the bottom margin in lines. Setting a bottom margin will
reduce the size of the printable area of the page by the number of lines set.
When the bottom margin is reached, the remainder of the page will be
skipped and printing will resume at the beginning of the next page (or top
margin if one is set). Adding a bottom margin may cause some data to be
printed on the wrong page if the program sending the data does not require
the margin.
Characters Per Inch
Characters/Inc
h
10
47
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Possible Values: 10*, 12, 13.3, 15, 16.74, 17.14,
20
This item sets the default character pitch in Characters Per Inch (CPI).
(Note that OCR-A and OCR-B characters are only valid at 10 CPI will
always print at 10 CPI regardless of this setting.)
Left Margin
Left Margin
Column 0
Possible Values: Column 0* … 268
This item sets the left margin in columns (characters) relative to the left edge
of the paper. The column width is based upon the current character pitch
(CPI). The left margin must be less than the right margin. The left margin
may be used to cause printing to begin farther to the right on a form. In
many cases using ALIGN PRINT may be preferable to using a left margin (see
“Aligning Print” on page 36) .
Right Margin
Right Margin
Column 272
Possible Values: Column 4 … 272*
This item sets the right margin in columns (characters) relative to the left
edge of the paper. A value of 272 is large enough to insure that characters
can be printed to the right end of the paper regardless of character pitch
(CPI). The right margin must be greater than the left margin. Text
characters that would have printed to the right of the margin will be
“wrapped around” and printed at the beginning of the next line. Graphic
data that would have printed to the right of the margin will be truncated (not
wrapped around). However, any data which would print before the right
margin but beyond the edge of the paper (either in the sprocket holes or on
the platen) will be truncated.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Font
Font
Epson FX FD
Possible Values: Epson FX FD*, DF, LQ;
PC English FD, DF, LQ;
PC Latin 2 FD, DF, LQ;
DEC LA120 FD, DF, LQ;
EBCDIC FD, DF, LQ;
OCR-A OQ;
OCR-B OQ
Roman–8 FD, DF, LQ, ML
Euro (858) FD, DF, LQ
ML (850) FD, DF, LQ
This item selects the default font to be used.
Draft Speed
Draft Speed
Normal
Possible Values: Normal*, Fast
This item selects whether the Draft Font (DF) or the Fast Draft (FD) font will
be selected when the printer receives a “select draft font” command from
the host computer. This will allow the Fast Draft font to be used with
programs which would not be able to otherwise.
Impact Force
Impact Force
Normal
Possible Values: Normal*, High
This item may be used to select High Impact for improved printing on
multipart forms that do not otherwise print well on the back copies.
Language
Language
USA
Possible Values: USA*, France, Germany, England,
Denmark, Sweden, Italy, Spain,
Japan, Finland
49
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
This item selects the character substitution table to be used for an alternate
language when printing. The Epson font must be selected in order for this
feature to work properly. The character substitutions are shown in the
following table.
Char Value 35 36 64 91 92 93 94 96 123 124 125 126
USA
#
#
$
$
$
$
$
¤
$
$
$
@
à
[
°
\
ç
]
§
Ü
]
^
^
^
^
^
Ü
^
^
^
`
`
{
é
ä
{
æ
ä
à
¨
¦
ù
ö
¦
}
è
ü
}
å
å
è
}
}
˜
¨
France
Germany
England
Denmark
Sweden
Italy
#
§
Ä
[
Ö
\
`
ß
˜
£
@
@
É
`
#
Æ
Ä
°
Ø
Ö
\
Å
Å
é
`
ø
ö
ò
ñ
¦
˜
#
é
ù
`
ü
ì
#
@
@
@
Spain
PTS
#
¡
Ñ
¥
¿
˜
Japan
[
]
`
{
˜
Zero Style
Zero
Normal
Possible Values: Normal*, Slashed
This item selects whether the numeral zero is printed with or without a slash
through it. (This is true for normal text characters. The optional Imager and
ImagerPlus Co-processors have a separate setup item for zero characters
they generate.)
Unidirectional Printing
Unidirectional
No
Possible Values: No*, Yes
This item selects unidirectional printing instead of bidirectional printing.
This may be used to improve the straightness of vertical lines for critical
applications such as printing small bar codes.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Interface Menu
The Interface Menu may contain several submenus. These submenus are
for setting up items pertaining to the hardware interfaces such as the serial
and parallel ports as well as the optional 10/100BaseT Ethernet or the
Wireless Print.
The Setup items for each interface are described in one of the following
sections.
RS-232C Serial Interface on page 52
Parallel/LAN Interfaces on page 57
Entering the Interface Menu
To Enter the Interface Menu, enter Setup and press the MENU button until
INTERFACE MENUis displayed on the top line as shown below.
INTERFACE MENU
Serial
The SUBMENUoptions for the INTERFACE MENUalways include the
Serial and Parallel ports. The other ports mentioned earlier will only be
displayed if they are installed in the printer. This is also true of the Imager
or ImagerPlus graphics options. To select the desired interface, press the
SUBMENU button until that interface is displayed on the bottom line. Next
press either of the ITEM buttons to begin displaying the items associated
with that interface. Each interface and the items which pertain to that
interface are listed on the following pages. Note that many items are the
same for more than one interface since the computer attached to that
interface may have different requirements for each of those items.
The factory default values are indicated with an asterisk (*) in this manual
(the asterisk does not appear on the printer’s display).
51
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
RS-232C Serial Interface Items
INTERFACE MENU
Serial
Emulation
Emulation
Epson
Possible Values: Epson*, IBM Proprinter,
DEC LA120, TTY,
Printek, ANSI X3.64
Genicom 3840, Genicom 3410
This item selects the emulation to be used whenever the serial port is active.
Emulation should be set to match the type of printer your software
supports.
Automatic Carriage Return
Auto CR
On
Possible Values: Off, On*
This item enables or disables automatic Carriage Returns (CR) whenever a
Line Feed (LF), Vertical Tab (VT), or Form Feed (FF) is received.
Automatic Line Feed
Auto LF
Off
Possible Values: Off*, On
This item enables or disables automatic Line Feeds (LF) when a Carriage
Return (CR) is received.
Perform Host Form Feed at Top-of-Form
Host FF at TOF
No
Possible Values: No*, Yes
52
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
This item selects whether Form Feeds (FF) will be performed when
received from the host computer if the paper is already positioned at the top
of form (TOF). Setting this item to Nowill help prevent blank pages.
Characters
Characters
Control
Possible Values: Control*, Printable
This item selects whether certain control character symbols will be printed
or be treated as control characters. The effect of this is dependent upon the
Emulationselected.
Minimum Buffer
Minimum Buffer
No
Possible Values: No*, Yes
This item selects whether the smallest possible I/O buffer should be used.
Setting this item to Nowill allow the printer to make maximum use of the
I/O buffer (see “Paper Out Fault” on page 61 for more information on
buffer size). Setting this to Yesmay decrease performance, but is useful
when using the printer with operating systems that try to keep track of
which page is currently being printed by the printer. This may also be useful
when using serial I/O with systems that do not respond quickly enough to
handshake signals.
Baud Rate
Baud Rate
9600
Possible Values: 110, 150, 300, 600, 1200, 2400,
4800, 9600*
This item selects the baud rate for the serial interface. This must be set to
match the baud rate setting on the host computer.
Data Bits
Data Bits
53
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
8
Possible Values: 8*, 7
This item selects the number of data bits in the serial character frame. This
must be set to match the character size setting on the host computer.
Stop Bits
Stop Bits
1
Possible Values: 1*, 2
This item sets the number of stop bits to be used at the end of the serial
character frame. This must be set to match the stop bit setting on the host
computer.
Parity
Parity
None
Possible Values: None*, Even, Odd
This item selects the parity checking requirements for the serial data bits.
This must be set to match the parity setting on the host computer.
Busy Signal Polarity
Busy Polarity
Low
Possible Values: Low*, High
This item selects the polarity of the busy signal (pin 11 of the RS-232C
interface). Busy is set whenever the printer is offline, the serial input buffer
is full, or another interface port is currently active (see “Automatic Port
Switching” earlier in this section).
Data Terminal Ready
DTR
Power On/Off
54
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Possible Values: Power On/Off*
Online/Offline
Busy/Not Busy
Selects the condition to be reflected by the DTR signal (pin 20 of the RS-
232C interface). In most cases, especially those involving a MODEM, this
signal should be set to indicate Power On/Off.
Selecting
Online/Offlinewill reflect only the condition indicated and does not
reflect a buffer full condition. Busy/Not Busy will cause DTR to
indicate both the online/offline status and buffer full condition (see “Busy
Polarity” above).
XON/XOFF Handshaking
XON/XOFF
Off
Possible Values: Off*, On
Enables or disables the transmission of the XON and XOFF characters
from the printer to the host to control data flow to the printer. XOFF will
be sent whenever the printer goes offline or the serial buffer is full. XON
will be sent when is again ready to receive characters.
ETX/ACK Handshaking
ETX/ACK
Off
Possible Values: Off*, On
Enables or disables the ACK response to receipt of the ETX character.
This handshake method is useful for conditions where there are long
transmission line delays such as telephone lines which may be routed
through satellites. An ACK character will be returned to the host computer
after an ETX character is received and processed. ETX characters used
for handshaking cannot be part of an escape sequence.
RTS/CTS Handshaking
RTS/CTS
OFF
Possible Values: Power On/Off*
55
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
If your Host system requires or supports hardware handshaking for data
flow control, it may be useful to change this parameter to ON. This may
apply especially to older Host systems using Full-duplex communications.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Parallel/LAN Interface Items
Since the optional LAN interface goes into the Parallel port, these interface
parameters are the same.
INTERFACE MENU
Parallel/LAN
Emulation
Emulation
Epson
Possible Values: Epson*, IBM Proprinter, DEC LA120,
TTY, Printek, ANSI X3.64,
Genicom 3840, Genicom 3410
This item selects the emulation to be used whenever the parallel port is
active. The emulation should be set to match the type of printer your
software supports.
LAN Setup
LAN Setup
Off
Possible Values: On, Off*
This item enables or disables the ability to control the optional Ethernet
interface card from the front panel. When set to On, the Serial Interface is
not available, and menu items for the Ethernet card follow. Consult your
Network Administrator before changing any of these items.
Note: Setting this item to On when the optional Ethernet interface
card is not present or optional control loop-back cable may
result in the printer appearing to “hang” when exiting the
Setup Menus. After 15 seconds, a LAN Timeout error will be
displayed. Press ONLINE, then enter the Setup Menus and
correct the problem.
IP Address Method
IP Address
Auto
57
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Possible Values: Auto*, Static
This item controls how the optional Ethernet interface card receives its
network address. When set to Auto, the Ethernet card will receive its
network address from a network DHCP server (typical installation). When
set to Static, the user sets the TCP/IP address, Subnet Mask and TCP/IP
Gateway address as follows:
IP Address
IP Address
192.160.0.27
Possible Values: 000.000.000.000 … 255.255.255.255
To set the TCP/IP address, use the SUBMENU key to select which digit
group you wish to change, and then use the UP/DOWN ARROW keys to
change the value. The value will change rapidly if the key is held down.
Subnet Mask
255.255.255.0
Subnet Mask
Possible Values: 000.000.000.000 … 255.255.255.255
To set the Subnet Mask, use the SUBMENU key to select which digit group
you wish to change, and then use the UP/DOWN ARROW keys to change the
value. The value will change rapidly if the key is held down.
IP Gateway
192.168.0.0
Gateway Address
Possible Values: 000.000.000.000 … 255.255.255.255
To set the TCP/IP Gateway, use the SUBMENU key to select which digit
group you wish to change, and then use the UP/DOWN ARROW keys to
change the value. The value will change rapidly if the key is held down.
Automatic Carriage Return
Auto CR
On
58
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Possible Values: Off, On*
This item enables or disables automatic Carriage Returns (CR) whenever a
Line Feed (LF), Vertical Tab (VT), or Form Feed (FF) is received.
Automatic Line Feed
Auto LF
Off
Possible Values: Off*, On
This item enables or disables automatic Line Feeds (LF) when a Carriage
Return (CR) is received.
Perform Host Form Feed at Top-of-Form
Host FF at TOF
No
Possible Values: No*, Yes
This item selects whether Form Feeds (FF) will be performed when
received from the host computer if the paper is already positioned at the top
of form (TOF). Setting this item to Nowill help prevent blank pages.
Characters
Characters
Control
Possible Values: Control*, Printable
This item selects whether certain control character symbols will be printed
or be treated as control characters. The effect of this is dependent upon the
emulation selected above.
Minimum Buffer
Minimum Buffer
No
Possible Values: No*, Yes
This item selects whether the minimum I/O buffer size should be used.
Setting this item to Nowill allow the printer to make maximum use of the I/O
59
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
buffer (see “Paper Out Fault” on page 61 for more information on buffer
size). Setting this to Yes may decrease performance, but is useful when
using the printer with operating systems that try to keep track of which page
is currently being printed by the printer.
Options Menu
The OPTIONS MENU contains items which do not pertain only to a
specific form or specific interface, but rather affect how the printer works
under all conditions. To access the options menu, enter Setup and then
press MENU until OPTIONS MENUis displayed
OPTIONS MENU
Note that the options menu has no submenus. Therefore, press either of the
ITEM buttons to begin displaying the items available. The factory default
values are indicated with an asterisk (*) in this manual (the asterisk does not
appear on the printer’s display).
Maximum Form Allowed
Max Form
Allowed
Form 2
Possible Values: Form 0 … Form 2* … Form 9
This item sets the last form number to be displayed for operator selection
with the FORM SELECT button or while in the FORMS MENU. This
allows the operator to see only the forms that are in use rather than having
to sort through several unused forms.
Note that when setting this value that you may not select a value less than
the form currently selected when Setup was entered, or less than the form
currently selected in the “Setup: FORMS” menu.
Automatic Scroll Delay
Auto-Scroll
1 Second Delay
60
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Possible Values: Off, 0, 1* to 15 Second Delay
This item sets the number of seconds to delay before scrolling the top of
form to the tear bar when the printer is idle (no additional data received
since the last print operation) and a form boundary (bottom of the form
according to the Form Length setting for the current form) has been
reached. If printing finishes and the form boundary has not been reached,
take the printer off line and the FORM FEED button may be used to advance
the form to the tear bar. This item may also be used to disable Auto-Scroll
by setting the value to Off. When disabled, the FORM FEED button must
always be used to advance the form to the tear bar.
Paper Out Fault Action
Paper Out
Fault
Finish Page
Possible Values: Finish Page*
Reprint Page
Break Page
This item selects what action is to be taken when a paper out condition
occurs. The action taken for each of the possible values is described in the
following paragraphs.
When Finish Pageis selected, the printer will attempt to print to the
bottom of the page when a normal paper out condition occurs. Conditions
that will prevent this from happening are when the end of paper is detected
too far from the end of the form (the printer assumes there is not a complete
page available), when reverse paper motion is attempted within the last one
inch of the form, or when a paper jam occurs. If the printer is unable to
finish printing the page, it will attempt to reprint the page as described below
(also refer to the Reprint Page Size option which follows). Note that if
highly precise printing is required in the last inch of the form, Finish
Pagemay not provide accurate enough paper motion since the form is no
longer controlled by the tractor mechanism .
When Reprint Pageis selected, the printer will stop printing as soon
as the end of paper or a paper jam condition is detected and the printer will
go off line. After a new box of forms is loaded, the printer will attempt to
reprint the current page from the beginning. If the printer is able to reprint
61
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
the page, Reprinting Page!will be displayed when the new form is
loaded (the previous partially printed page should probably be discarded).
If the printer is unable to reprint the page, the page will be broken,
Cannot Reprint - Page Too Largewill be displayed, and
printing will resume where it left off as described in the next paragraph. The
printer’s ability to complete the reprint successfully depends on whether the
data for the current page is still in the printer’s memory. Refer to the
following Reprint Page Size option for more information regarding how
much data may be retained.
When Break Pageis selected, the printer will stop printing and go off
line as soon as a paper out or paper jam condition is detected. After a new
box of forms is loaded, printing will resume where it left off. The Break
Pagesetting is appropriate when you know a page is too large to reprint
(exceeds available buffer size, e.g. contains large graphic images). This will
suppress the error message Cannot Reprint before printing
continues.
Character to Ignore
Char. To
Ignore
255
Possible Values: 0, … 255*
This allows a single 8-bit character to be discarded as it is received. This is
useful when the host application is sending an unwanted control character,
for example. Values are in decimal, with printable characters displayed to
the left of the decimal value.
To use this feature:
1) Press the UP/DOWN ARROW keys to select the desired character
decimal value. Printable characters will appear to the left of the
number.
2) Press the ITEM button to display Ignore Character ON/Off, then the
UP/DOWN ARROW keys to turn the feature On or Off.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
This feature should not be turned on unless needed.
Top of Barcode
Top of Barcode
Off
Possible Values: On, Off*
In Genicom 3840 or 3410 Emulation, this feature repositions the print head
at the top of a barcode after the barcode has printed. When disabled,
printing continues from the bottom of the barcode. This feature has no
meaning in other emulations.
Top of Oversized
Top of
Oversized
Off
Possible Values: On, Off*
In Genicom 3840 or 3410 Emulation, this feature repositions the print head
at the top of oversized characters after the oversized characters have
printed. When disabled, printing continues from the bottom of the oversized
characters.
This feature has no meaning in other emulations.
User Language
User Language
English
Possible Values: English*, French, German
This selects the front panel language that will be used by the printer's LCD
screen. Press the UP/DOWN ARROW keys to change the selection. Note:
If you change the selected language, you may find it difficult to
return to this menu to correct it! Verstechen Sie?
Page Size
8192
Characters
Reprint Page Size
63
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Possible Values: 0, …, 8192*, …, 28672
This item selects how much of the 32K byte input buffer is set aside for
reprinting a page when Finish Pageor Reprint Pagehas been
selected for the Paper Out Fault Action item (see above). The value
selected (0 to 28K bytes in 1K byte increments) should be set to
accommodate the largest page expected, but not unnecessarily large since
the larger this is set, the smaller the effective I/O buffer. The 8K byte
default setting should be large enough to hold most pages of text, but may
not be large enough to hold more complex or graphic filled pages. If the
page size selected is not large enough, the page will be broken as described
under Paper Out Fault Action item above.
If the Paper Out Fault Action item is set to Break Page, the Reprint
Page Size may be set to 0to allow the largest possible I/O buffer.
Truncate Lines
No
Truncate Long Lines
Possible Values: Yes, No*
When this item is set to Yes, long text lines that would wrap around the next
line will be terminated at the right margin column or the right usable edge of
the platen, whichever is reached first. The remainder of the characters in the
line are discarded. Graphics printing always truncates.
Ribbon Checking
Ribbon Check
On
Possible Values: On*, Off
This item selects whether or not ribbon checking is active. This feature
works exclusively with Printek ribbons. When Ribbon Checking is On, the
printer alerts the operator if a ribbon is not installed, or if the ribbon life has
been reached (see Ribbon Life below). Ribbon Check may be turned off if
these features are not desired.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Ribbon Check may also be turned off to allow the use of non-Printek brand
ribbons. Using non-Printek ribbons may limit the warranty on the print
head, so before turning Ribbon Check off, please read “Why Use Only
Printek® Brand Ribbons” on page 10 and the warranty information on page
114. Note that turning this feature off while still using Printek brand ribbons
will not affect the extended warranty.
Ribbon Life
Ribbon Life
23 Million
Chars
Possible Values: 5 … 23* … 30 Million Chars
This item sets the number of “draft equivalent” characters to be printed
before the Change Ribbonmessage is displayed. “Draft equivalent” is
an indication of the average density, or number of dots, in a draft font
character. Characters printed using other fonts are weighted according to
their own density. Typically, fast draft characters have fewer dots while
letter quality and optical quality fonts have more and are weighted as fewer
or more draft characters accordingly. Graphics data are weighted
according to the actual number of dots printed.
ImagerPlus Graphic Card
OPTIONS MENU
ImagerPlus
The printer will automatically display ImagerPlus as shown above when the
interface is installed. The descriptions in this manual are brief. For more
information, please refer to the appropriate ImagerPlus manual.
Emulation
Emulation
QMS CodeV v2
Possible Values: QMS CodeV v2*, PTX CodeV v2,
Printronix IGP
65
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
This item sets the Imager or ImagerPlus emulation mode. QMS CodeV
v2selects QMS Code V version 2, PTX CodeV v2selects Printronix
Code V version 2.
Control Character
ControlCharact
er
^ (5E Hex)
Possible Values: ^ (5E Hex)*
SOH (01 Hex) through HT (09 Hex),
SO (0E Hex) through (FF Hex)
This item sets the control character used to begin commands. The
character normally used for QMS is the caret (^) and the character nomally
used for IGP is the tilde (~) (if you change the emulation to Printronix
IGP, you may need to change the control character to the tilde).
Line Terminator
Line
Terminator
LF
Possible Values: LF*, CR
This item sets the line terminating character to a Line Feed or a Carriage
Return.
Bar Code Density
Bar Code
Density
High-Res
Possible Values: Low-Res, Medium-Res, High-Res*,
Graphics Med-Res
This item sets the density, or graphics resolution, for bar codes.
QMS Character Set
(QMS CodeV v2 and PTX CodeV v2 only)
QMS Char Set
USA
66
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Possible Values: USA
France
United Kingdom Italy
Sweden/Finland Spain
Norway/Denmark PC Subset
Japan
Germany
CodeV Version1
This item selects the character set.
^PY Translation Mode
(QMS CodeV v2 and PTX CodeV v2 only)
^PY
Translation
Not Active
Possible Values: Not Active*, Active
This item selects whether or not Filter Mode is active at power on or reset.
^F Free Format Mode
(QMS CodeV v2 and PTX CodeV v2 only)
^F Free Format
Not Active
Possible Values: Not Active*, Active
This item selects whether or not the Free Format Mode is active in Filter
Mode.
^ X Ignore Data Mode
(QMS CodeV v2 and PTX CodeV v2 only)
^X Ignore Data
Not Active
Possible Values: Not Active*, Active
This item selects whether data will be ignored until a ^A is received.
Imager/ImagerPlus Zero Style
(QMS CodeV v2 and PTX CodeV v2 only)
Imager Zero
Slashed
Possible Values: Slashed*, Normal
This item selects the type of zero character (Ø or O) to be printed by the
Imager or ImagerPlus.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Line Registration
(QMS CodeV v2 and PTX CodeV v2 only)
LineRegistrati
on
Not Maintained
Possible Values: Not Maintained*, Maintained
This item selects whether or not the form will automatically be advanced to
the next line boundary when Filter Mode is exited.
Vertical DPI Resolution
(QMS CodeV v2 and PTX CodeV v2 only)
Vertical DPI
72
Possible Values: 72*, 70
This item sets the vertical resolution to 72 or 70 Dots Per Inch.
Vertical Text Spacing
(QMS CodeV v2 and PTX CodeV v2 only)
Vertical Text
SP
Version 2
Possible Values: Version 2*, Version 1
This item selects whether text should be spaced vertically as in Code V
version 1 or version 2.
Code V Space Fields
(QMS CodeV v2 and PTX CodeV v2 only)
CodeV SP
Fields
Process
Possible Values: Process*, Ignore
This item selects whether Code V space fields should be processed.
IGP Character Set
IGP Char Set
ASCII
Possible Values: ASCII
English
Dutch
France
Germany
Sweden
68
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Denmark
Norway
Finland
Spain
Italy
Turkey
This item selects the character set.
Delete Logos
Delete Logos
No
Possible Values: No*, Yes
This item selects whether logos should be deleted when a form is deleted.
Quiet Mode
Quiet Mode
Not Active
Possible Values: Not Active*, Active
This item selects whether or not the quiet mode is active at power on.
Spacing Mode
Spacing
IGP 10/20/40
Possible Values: IGP 10/20/40*, IGP 30
This item selects the Spacing mode.
Test Menu
The TEST MENUis used to access some testing as well as some record
keeping items. To access the test menu, enter Setup and press the MENU
button until TEST MENUis displayed as shown below.
TEST MENU
Next press either of the ITEM buttons to access the test modes available.
69
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Print the Menus
Print the
Menus
No
Possible Values: No*, Current Values
This item may be used to print the entire list of current values.
Current Values will print only the items relevant to the current printer
configuration and their current values. This provides a means of record
keeping or “backup”, so that the values can be checked and restored in
case an operator inadvertently changes one.
After setting this value, press ONLINE to begin printing. After printing is
completed, the value of this item will automatically return to No. Note that
once printing begins, taking the printer off line for any reason (ONLINE
button pressed, ribbon lid or paper door opened, or a paper fault) will
cause printing to be aborted.
Test Mode
Test Mode
Off
Possible Values: Off*, Barber Pole,
Hex Dump, Demos
When this item is set to Barber Pole, the printer will print a rotating
character pattern. Printing may be started and stopped with the ONLINE
button.
When set to Hex Dump, the printer will print all received data in a special
debug format which may be used by programmers to solve software
problems. For more information, refer to the Hex Dump section of the
FormsMaster 8000se series Programmer’s Manual.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R C O N F I G U R A T I O N
Note when in Barber Pole mode and Hex Dump mode, if the printer is
taken OFFLINE during printing, the printer will remain in these modes. If the
printer is put back ONLINE, printing will resume. To exit either of these
modes, return to the TEST MENUand use the UP/DOWN arrow keys to
set “TEST MODE” to OFF.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
FORM CONSTRUCTION
Form Construction
Although the FormsMaster 8000se series printers have been designed to
handle difficult forms, you may come across a form that does not feed
reliably or provide adequate print quality on all copies.
One of the main causes of paper misfeeds is a form that is “tented”. Tenting
is a tent-like bulge at the perforation when forms are unfolded from the box.
The printer allows a maximum form thickness of 0.025 inches, which a
badly tented form may exceed.
Tenting is usually caused by glue drying on the perforation after the forms
maker puts the forms into the box, or forms which are not glued at all.
Forms with solid glue lines which run vertically down the entire form are the
most susceptible. If you experience such a problem, request “interrupted
glue line” forms from your vendor. This method stops the glue
approximately three-quarters of the way down the form and then resumes
gluing at the top of the next form. The gluing should not begin too far below
the top of the form or pages of the form will be able to fan apart and be a
potential cause of jamming.
Another area where not all forms are alike is in the quality of carbon paper
used, or in the way carbonless inks are applied. If the back copies of your
form are too light, request a quick-release carbon or a higher quality
carbonless inking method.
73
Download from Www.Somanuals.com. All Manuals Search And Download.
S P E C I F Y I N G F O R M S
Form Layout Considerations
When designing preprinted forms, the most common problem is forms that
are designed “too tight”. This means that boxes where data have to be
printed are just barely large enough for the data, and that even the slightest
misalignment will cause characters to be printed on at least one of the lines
that form the box.
While the print alignment can be adjusted on the FormsMaster 8000se
series printer to 1/100th of an inch, this is often too much to expect of the
forms manufacturer. Where the preprinted information is placed in respect
to the tractor holes on the form often varies on every other form in a single
box of forms, or from one box of forms to the next.
To help avoid this situation, create larger areas for data by allocating blank
lines in the printed data for horizontal lines, and allocating blank columns for
vertical lines. If this is not possible due to the amount of data that has to be
placed on the form, avoid using a dark color to form the preprinted lines
and boxes. Use a lighter color, preferable other than a gray, that will allow
the printed characters to still be read if misalignment occurs.
74
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND
TROUBLESHOOTING
Error Messages
This section provides a partial list of fatal errors. Fatal errors typically
cannot be recovered from without the loss of data. In each case, ERRORis
shown on the top line of the display and one of the following messages is
shown on the bottom line. Suggested solutions for each of these messages
are listed to the right of each error message in the table which follows. If
the suggested solution does not solve the problem, please refer to
“Obtaining Service” on page 76.
Note that none of these messages “flash” on the display. Messages which
are flashed on the display are discussed in the “Common Error Conditions”
section on page 38.
Other errors which are not listed here or in “DAILY OPERATION” should
be reported to the company where you purchased your printer, or to your
nearest Authorized Service Center. If you do not know the name or
number of your nearest Authorized Service Center, see “Obtaining
Service” later in this section.
75
Download from Www.Somanuals.com. All Manuals Search And Download.
M A I N T E N A N C E A N D T R O U B L E S H O O T I N G
Error Message
Possible Solution
Head Blocked?
Check print head carriage area for
obstructions.
Head Gap
Usually a result of a bad paper jam.
Check for paper wedged in the print head
nose shield area.
I/O Overflow
Make sure handshaking parameters set in
the printer and at the host computer match
each other.
Make sure interface cables are wired
correctly.
Preventive Maintenance
Very little preventive maintenance is required by your FormsMaster 8000se
series printer. It is only suggested that you periodically clear out any
excessive paper dust.
Also, the various bearings used in the FormsMaster 8000se should not
require any lubrication. If you do choose to lubricate any bearings, use only
a 30 Wt. non-detergent motor oil. DO NOT use any grease or any
vegetable based oils.
Obtaining Service
If your FormsMaster 8000se series printer should require service, please
contact the company where you purchased the printer. If you do not know
where the printer was purchased, please call 800-368-4636 to obtain the
76
Download from Www.Somanuals.com. All Manuals Search And Download.
name and number of your nearest Printek Authorized Service Center or to
arrange for factory service.
77
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED SETUP FEATURES
Security Menu
The SECURITY MENUis for Information System managers who want to
be able to set up a printer and then “lock out” operator changes to the
various menus. This method of security may be set independently for the
Align Print, the Forms menu, the Interface menu, or the Options menu.
When set to Edit Allowed, the user is allowed to make changes to
any item in the menu selected. When set to View, the operator can look
at the settings, but cannot edit, or change the values. When set to
Initialize, the printer will reset all values in that menu (and
associated submenus) to the factory default values and security will be set
back to Edit Allowed.
The SECURITY MENU is more difficult to enter than other menus. To be
able to access this menu, the printer must be powered on while pressing
the MENU button. After the printer has finished its power up self-tests,
enter Setup and press the MENU button until SECURITY MENU is
displayed on the top line. Next press either of the ITEM buttons to begin
setting security.
Align Print
Align Print
Edit Allowed
Possible Values: Edit Allowed, View Only,
Initialize
79
Download from Www.Somanuals.com. All Manuals Search And Download.
A D V A N C E D S E T U P F E A T U R E S
This item selects whether values set using Align Print (see Aligning Print on
page 36) can be edited or only viewed by the operator. Initialize
will reset the Align Print values for all forms to zero.
80
Download from Www.Somanuals.com. All Manuals Search And Download.
Forms Menu
Forms Menu
Edit Allowed
Possible Values: Edit Allowed, View Only, Initialize
This item selects whether items in the FORMS MENUcan be edited or only
viewed by the operator. Initialize will reset the value of all the items
for all forms to factory default values.
Interface Menu
Interface Menu
Edit Allowed
Possible Values: Edit Allowed, View Only, Initialize
This item selects whether items in the INTERFACE MENUcan be edited
or only viewed by the operator. Initializewill reset the value of all
the items for all interfaces to factory default values.
Options Menu
Options Menu
Edit Allowed
Possible Values: Edit Allowed, View Only,
Initialize
This item selects whether items in the OPTIONS MENUcan be edited or
only viewed by the operator. Initializewill reset the value of all the
items in the options menu to factory default values.
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
USING REMOTE SETUP
The PrintMaster 8000se Series printers may be completely configured for
operation by using the front panel buttons to access the printer setup menus.
In addition, many of the items that can be configured via the front panel
setup menus can also be configured remotely as described in this chapter.
Remote Setup via Windows Application
Printek provides a remote setup program for Windows 95, 98, 2000 and
NT users. This provides a convenient method for graphically configuring
the printer. Visit www.printek.com to download the free application.
Remote Setup via Generic Text File
Remote setup commands are placed in a remote setup file on a host
computer. This file may then be sent to the printer. The remote setup file
must be a text only file* with each line terminated by a Line Feed (LF)
character.
The available commands listed below are shown with a combination of
upper and lower case letters to enhance readability. However, the
commands are not case sensitive. All characters are converted to upper
case before processing (except for form names, which are contained in
double quotes). White space may also be inserted to enhance readability; it
will be stripped from the commands before processing.
Each line of the file is processed individually, and must conform to one of
four possible formats:
1. A blank line (ignored).
2. A comment line, which begins with a semicolon ";" (ignored).
3. A heading line, which is enclosed in square brackets "[]".
4. An item setup line, of the format item=value.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
A D V A N C E D S E T U P F E A T U R E S
Each item setup line must appear under the appropriate heading line. The
first heading line ni the file must be [BeginPrintekSetup]. The
last heading line in the file must be [EndPrintekSetup]. All other
heading lines and item setup lines are optional.
If any errors exist in the remote setup file, no changes will be made to the
printer configuration. When possible, the printer will indicate the line
number in the file where the first error occurred. Counting of lines begins
with 1 at the [BeginPrintekSetup] heading line. Any lines
preceding this will not be processed, and will not be counted.
Before sending the remote setup file to the printer, minimal setup is required
via an escape sequence. The I/O interface to be used for remote setup
must be configured appropriately to communicate with the host system, and
the printer must be placed in remote setup mode. This is done by sending a
3-byte escape sequence to the printer. This sequence is ESC ESC ; or
hexadecimal 1B 1B 3B. This sequence may be included at the beginning of
the text file.
After this is done, the printer will reset, beep the bell to alert the operator,
and display the message "Waiting For Remote Setup". The remote
setup file may now be sent to the printer.
After the printer receives the remote setup file (without error), all specified
configuration changes will be made, the printer will reset. When this reset is
complete, the printer will be ready for normal interaction with the host
system. Errors in the setup file are handled as Fatal errors. Test the setup
file before sending it to a remote printer.
The available heading lines, and item setup lines, are documented below.
Note that all the legal values are shown for each item, but in use only one
value may be supplied in the setup file. An example file follows these
definitions.
*Note that the 3-byte escape sequence can be included as the first 3 bytes
in the remote setup file.
84
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Setup Line Definitions
[BeginPrintekSetup]
AlignPrint=FactoryDefaults
Forms=FactoryDefaults
Interfaces=FactoryDefaults
Options=FactoryDefaults
Security=FactoryDefaults
[Form0] ... [Form9]
MovePrintLeft=0.00 ... 9.99
MovePrintRight=0.00 ... 9.99
MovePrintUp=0.00 ... 9.99
MovePrintDown=0.00 ... 9.99
FormName="UPTO16CHARACTERS"
TractorPath=Front,Center,Rear,Center+Rear,
Front+Center+Rear
AutomaticCut=No,Yes
LinesPerInch=6,8
FormLength=1 ... 227
TopMargin=0 ... 226
BottomMargin=0 ... 226
CharactersPerInch=10,12,13.3,15,16.74,17.14,2
0
LeftMargin=0 ... 268
RightMargin=4 ... 272
Font=Epson_FX_FD,Epson_FX_DF,Epson_FX_LQ,
PC_English_FD,PC_English_DF,PC_English_
LQ,
PC_Latin2_FD,PC_Latin2_DF,PC_Latin2_LQ,
DEC_LA120_FD,DEC_LA120_DF,DEC_LA120_LQ,
EBCDIC_FD,EBCDIC_DF,EBCDIC_LQ,OCR_A_FD,
OCR_B_FD,Roman8FD,DF,LQ,ML,
Euro(858)FD,DF,LQ,ML(850)FD,DF,LQ
DraftSpeed=Normal,Fast
ImpactForce=Normal,High
Language=USA,France,Germany,England,Denmark,
Sweden,Italy,Spain,Japan,Finland
Zero=Normal,Slashed
Unidirectional=No,Yes
[SerialInterface]
85
Download from Www.Somanuals.com. All Manuals Search And Download.
A D V A N C E D S E T U P F E A T U R E S
Emulation=ANSI_X3.64,Epson,IBM_Proprinter,
DEC_LA120,TTY,Printek,Genicom 3840,
Genicom 3410,DEC-210
AutoCR=Off,On
AutoLF=Off,On
HostFFatTOF=No,Yes
Characters=Control,Printable
MinimumBuffer=No,Yes
BaudRate=110,150,300,600,1200,2400,
4800,9600
DataBits=8,7
StopBits=1,2
Parity=None,Even,Odd
BusyPolarity=Low,High
DTR=Power,Online,Busy
XON/XOFF=Off,On
ETX/ACK=Off,On
[ParallelInterface]
Emulation=ANSI_X3.64,Epson,IBM_Proprinter,
DEC_LA120,TTY,Printek, Inc,
Genicom 3840,Genicom 3410,DEC_210
AutoCR=Off,On
AutoLF=Off,On
HostFFatTOF=No,Yes
Characters=Control,Printable
MinimumBuffer=No,Yes
[Options]
MaxFormAllowed=0 ... 9
AutoScroll=Off,1 ... 15
PaperOutFault=BreakPage,ReprintPage,FinishPag
e
PageSize=0K . . . 28K
RibbonCheck =Off,On
RibbonLife=5…30
TopOfBarcode+Off, On
TopOfOversized=Off, On
IgnoreCharacter=Off, On
CharToIgnore=0 . . . 255
TruncateLines=No,Yes
86
Download from Www.Somanuals.com. All Manuals Search And Download.
[Imager/ImagerPlusInterface]
Emulation=QMSCodeVVersion2,
PrintronixCodeVVersion2,PrintronixIGP
ControlCharacter=01h ... 09h,0Eh ... FFh
LineTerminator=LF,CR
BarCodeDensity=LowRes,MediumRes,HighRes,
GraphicsMediumRes
87
Download from Www.Somanuals.com. All Manuals Search And Download.
A D V A N C E D S E T U P F E A T U R E S
QMSCharacterSet=USA,UnitedKingdom,
Sweden/Finland,Norway/Denmark,Japan,
Germany,France,Italy,Spain,PCSubset,
CodeVVersion1
Translation=NotActive,Active
FreeFormat=NotActive,Active
IgnoreData=NotActive,Active
ImagerZero=Slashed,Normal
LineRegistration=NotMaintained,Maintained
VerticalDPI=72,70
VerticalTextSpacing=Version2,Version1
CodeVSpaceFields=Process,Ignore
IGPCharacterSet=ASCII,Germany,Sweden,Denmark,
Norway,Finland,English,Dutch,
France,Spain,Italy,Turkey
DeleteLogos=No,Yes
QuietMode=NotActive,Active
Spacing=IGP10/20/40,IGP30
[Security]
AlignPrint=ViewOnly,EditAllowed
FormsMenu=ViewOnly,EditAllowed
InterfaceMenu=ViewOnly,EditAllowed
OptionsMenu=ViewOnly,EditAllowed
[EndPrintekSetup]
Remote Setup Example File
The following example will set up three forms. Before the forms are set up,
“AlignPrint” and all “Forms” will be reset to their factory default values so
that only the “non-default” values have to be set.
The first form will begin printing one line from the top-of-form, be named
“CHECKS”, have a form length of 42 lines (7 inches at 6 LPI), and use the
Epson FX Draft font.
The second form will begin printing two characters (at 10 CPI) from the left
edge and two lines (at 6 LPI) from the top edge of the form. The name will
be “INVOICES” and will print using the Epson FX Draft font.
88
Download from Www.Somanuals.com. All Manuals Search And Download.
The third form will begin printing two lines (at 8 LPI) from the top edge of
the form. The name will be “REPORTS”, and printing will be at eight LPI
with a form length of 8½ inches.
;
Example setup file for three forms.
[BeginPrintekSetup]
AlignPrint=FactoryDefaults
Forms=FactoryDefaults
[Form0]
MovePrintDown=0.17
FormName="CHECKS"
FormLength=42
Font=Epson_FX_DF
[Form1]
MovePrintRight=0.20
MovePrintDown=0.33
FormName="INVOICES"
Font=Epson_FX_DF
[Form2]
MovePrintDown=0.25
FormName="REPORTS"
LinesPerInch=8
FormLength=68
CharactersPerInch=12
[EndPrintekSetup]
89
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE OPTIONAL SETUP
MODULE
Introduction
The optional Setup Module is a small cartridge that plugs directly into the
RS-232 Serial connector on the rear of any FormsMaster 8000se series
printer. This module is used to store a second copy of the current Setup
configuration of the printer. This may then be used to restore settings after a
printer is serviced or to copy the same configuration settings to another
printer. These uses are discussed immediately following the installation
instructions.
Setup Module Installation
To install the Setup Module, perform the following steps.
1. Turn off power to the printer.
2. Disconnect the cable plugged into the serial port if one is present.
3. Plug the Setup Module into the serial port.
4. If a cable was present in step 2, reconnect it to the connector on the
rear of the Setup Module.
5. Turn on power to the printer.
6. If this is not the first time the Setup Module has been connected to a
printer, then proceed with step 7.
If this is the first time the Setup Module has ever been attached to a
printer, the printer will temporarily display the following message and
the ONLINE indicator will be yellow. When the message disappears,
91
Download from Www.Somanuals.com. All Manuals Search And Download.
U S I N G T H E O P T I O N A L S E T U P M O D U L E
installation is complete and the printer will continue with its normal
power up procedure.
Initializing
Setup Module
7. The printer will now compare the configuration data in its internal
memory to the data in the Setup Module. If the data are not an exact
match, the printer will proceed with step 8.
If the data in the printer and the data in the module are an exact
match, installation is complete and the printer will complete its power
up procedure.
8. The printer has now determined that the data in the Setup Module
does not exactly match the data in the printer’s internal memory. The
printer will now display the following message, the ONLINE indicator
will flash yellow and the bell will beep to get the operator’s attention.
Proceed to step 9.
New Setup
Module
Detected
9. Press the ONLINE button. The printer will now stop flashing the
ONLINE indicator (will remain yellow) and display the following
message. You must now make one of the selections as described
below.
¬Copy to
Printer
¬Copy to
Module
If you wish to copy the Setup data to the printer from the Setup
Module, press the button indicated by the arrow next to Copy to
Printer(the SETUP button). The printer will display the following
92
Download from Www.Somanuals.com. All Manuals Search And Download.
U S I N G T H E O P T I O N A L S E T U P M O D U L E
message and will now be configured according to the information that
was in the Setup Module.
Copying Setup
to Printer
If you wish to copy the Setup data to the Setup Module from the
printer, press the button indicated by the arrow next to Copy to
Module(the ALIGN PRINT button). The printer will display the next
message and the Setup Module will now contain a copy of the Setup
information in the printer.
Copying Setup
to Module
After one of the above selections is made, installation is complete, the
ONLINE indicator will be turned off and the printer will finish its
power up procedure. If you are not sure which button to press, refer
to either of the following sections for more information.
Using the Setup Module to Maintain a
Backup Copy of Setup Information for a Single Printer
This use of the Setup Module provides a method of automatically
maintaining a copy of the Setup configuration in case a printer should ever
need to be repaired or if it is replaced under a service contract.
To use the Setup Module in this manner, you only need to perform the
installation procedure once and then forget about it. The printer will
automatically keep the Setup Module updated with any changes that are
made to the printer using the front panel Setup as described in “Printer
Configuration” beginning on page 41. As long as the Setup Module remains
on the same printer, the installation procedure will not have to be repeated.
If the printer does someday require repair or replacement, simply perform
the installation procedure again on the repaired or replacement printer and
in step 9 choose “Copy to Printer”. Depending upon what was repaired in
93
Download from Www.Somanuals.com. All Manuals Search And Download.
U S I N G T H E O P T I O N A L S E T U P M O D U L E
the printer, the Setup information in the printer’s memory may not have
been changed. In this case the printer will power up normally and no
message will be displayed.
Using the Setup Module to
Copy Setup Data From One Printer to Another
This use of the Setup Module is beneficial when installing or updating
several printers that need to be configured exactly the same. To do this,
you will need to perform the installation procedure once for each printer.
First, install the Setup Module on the printer where the Setup data is to be
copied from. If the printer determines that steps 8 and 9 are required,
choose “Copy to Module” in step 9 and allow the printer’s power up
procedures to complete. If any additional changes need to be made to the
configuration of this printer, enter Setup and make them before removing
the Setup Module. Any changes made will automatically be stored both in
the printer’s internal memory and the Setup Module.
You may now power off the printer and remove the Setup Module.
Remember to reconnect the serial cable if one was attached.
Now perform the installation procedure on each of the printers that are to
be configured the same as the first. In step 9 be sure to choose “Copy to
Printer”. After the Setup Module is removed, remember to reconnect the
serial cable if one was attached.
Note: Setup modules for Printek FormsMaster 8000se Series
printers and PrintMaster 850 Series printers are not
interchangeable. Data backup will not take place if the
modules are used on the wrong printer.
94
Download from Www.Somanuals.com. All Manuals Search And Download.
PRINTER RESET CONDITIONS
The following list describes conditions that are assumed whenever power is
applied to the printer, changes have been made in SETUP, or a reset
escape sequence is received (when the printer is operating in an emulation
mode that supports such a sequence).
This list includes all variables that you can modify for all emulations, even
though some emulations cannot modify all of the variables shown. Refer to
the appropriate section of this manual for the emulation you are using.
Variable
Reset Condition
character pitch
left margin
right margin
line pitch
form length
top margin
bottom margin
font
impact mode
language
normal/slashed zero
auto cut mode
unidirectional mode
top of form
according to current form setup
according to current form setup
according to current form setup
according to current form setup
according to current form setup
according to current form setup
according to current form setup
according to current form setup
according to current form setup
according to current form setup
according to current form setup
according to current form setup
according to current form setup
set to current position
discarded
text in an incomplete line
input buffer
control of data bit 8
control character symbols
italics
cleared (unless reset from host)
accepted as received
according to interface setup
off
double high
off
double strike
double wide
off
off
emphasized
off
superscript/subscript
underline
off
off
95
Download from Www.Somanuals.com. All Manuals Search And Download.
P R I N T E R R E S E T C O N D I T I O N S
horizontal tabs
vertical tabs
to every eight columns
cleared
96
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL CODE AND ESCAPE
SEQUENCE SUMMARIES
Genicom 3840 and 3410 Emulation
BEL
Bell
BS
Backspace
CR
Carriage Return
CSI
ESC D
Control Sequence Introducer
Line Feed
ESC E
New Line
ESC ESC n
ESC H
Select Software Interface n
Set Horizontal Tab
ESC J
Set Vertical Tab
ESC K
Subscript Printing
ESC L
Superscript Printing
6 Pin Graphics Mode
Oversize Font / Graphic Size Modification
Line / Character Spacing
Horizontal Position Absolute
Horizontal Position Relative
Vertical Position Absolute
Vertical Position Relative
Vertical and Horizontal Position Absolute
Clear Tabs
Set Auto CR on LF
Horizontal Position Backwards
Vertical Position Backwards
Reset Auto CR on LF
Font and Print Modes
Paper Path
ESC P <graphics> ESC \
ESC [(p1);(p2)<SP>B
ESC [(p1);(p2)<SP>G
ESC [(p)`
ESC [(p)a
ESC [(p)d
ESC [(p)e
ESC [(p1);(p2)f
ESC [(Ps)g
ESC [(p)h
ESC [(p)j
ESC [(p)k
ESC [(p)l
ESC [(p1);...(pn)m
ESC [(p1)p
ESC [(p1)q
ESC [(p1);(p2);(p3)r
Graphics Density
Forms Setup
97
Download from Www.Somanuals.com. All Manuals Search And Download.
C O N T R O L C O D E S A N D E S C A P E S E Q U E N C E S
Genicom 3840 and 3410 Emulation (cont.)
ESC [(p1);(p2)s
Margins Setup
ESC [(p1)t
ESC [(p1);(p2);...(p22)u
ESC [(p1);(p2);...(p12)v
ESC [(p1);(p2)<SP>{
Oversized Font / Barcode Mode
Set Horizontal Tabs at Certain Positions
Set Vertical Tabs at Certain Positions
Paper Shear
ESC [(p1);(p2);...(p12)}
ESC ]6;4;(p3);(p4)ESC\
ESC c
ETX
FF
Set Barcode Parameter
Straps and Options
Reset
End of Text
Form Feed
HT
Horizontal Tab
HTS
IND
LF
Set Horizontal Tab Stop
Index
Line Feed
NEL
PLD
PLU
VT
Next Line
Partial Line Down (Subscript)
Partial Line Up (Superscript)
Vertical Tab
VTS
Set Vertical Tab Stop
ANSI x3.64 Emulation
BEL
Bell
BS
Backspace
CR
Carriage Return
CSI
Control Sequence Introducer
Line Feed
ESC D
ESC E
New Line
ESC ESC n
ESC H
Select Software Interface n
Set Horizontal Tab Stop
Set Vertical Tab Stop
Partial Line Down
ESC J
ESC K
ESC L
Partial Line Up
ESC [ n1 ; n2 SP G
ESC [ n `
ESC [ n a
ESC [ n d
ESC [ n e
ESC [ g
ESC [ 0 g
Set Character and Line Spacing
Absolute Horizontal Tab
Relative Horizontal Tab
Absolute Vertical Tab
Relative Vertical Tab
Clear Horizontal Tab Stop
Clear Horizontal Tab Stop
98
Download from Www.Somanuals.com. All Manuals Search And Download.
C O N T R O L C O D E S A N D E S C A P E S E Q U E N C E S
ESC [ 1 g
ESC [ 2 g
ESC [ 3 g
ESC [ 4 g
ESC [ 20 h
ESC [ 20 l
ESC [ n m
ESC c
ETX
Clear Vertical Tab Stop
Clear All Horizontal Tab Stops
Clear All Horizontal Tab Stops
Clear All Vertical Tab Stops
Select Automatic Carriage Return
Cancel Automatic Carriage Return
Select Graphic Rendition
Reset
End of Text
FF
Form Feed
Horizontal Tab
HT
HTS
Set Horizontal Tab Stop
Line Feed
IND
LF
Line Feed
New Line
NEL
PLD
Partial Line Down
Partial Line Up
PLU
VT
Vertical Tab
VTS
Set Vertical Tab Stop
Epson FX Emulation
BEL
Bell
BS
Backspace
CAN
Cancel Line
Carriage Return
Cancel Condensed Mode
Deselect Printer
Cancel Double-Wide Mode (one line)
Delete Character
CR
DC2
DC3
DC4
DEL
ESC ! n
ESC #
ESC $ n1 n2
ESC * m n1 n2 data
ESC - n
ESC 0
ESC 1
ESC 2
ESC 3 n
ESC 4
ESC 5
ESC 6
ESC 7
ESC <
Master Print Mode Select
Cancel MSB Control
Absolute Horizontal Tab
m DPI Graphics
Underline Mode
Select 8 LPI
Set Line Spacing to 7/72"
Select 6 LPI
Set Line Spacing to n/216"
Select Italic Mode
Cancel Italic Mode
Enable Printing of High Symbols
Disable Printing of High Symbols
Unidirectional Mode (one line)
99
Download from Www.Somanuals.com. All Manuals Search And Download.
C O N T R O L C O D E S A N D E S C A P E S E Q U E N C E S
ESC =
Set MSB to 0
Epson FX Emulation (cont.)
ESC >
ESC @
Set MSB to 1
Reset
ESC A n
ESC B n1 n2 ... nx NUL
ESC C NUL n
ESC C n
ESC D n1 n2 ... nx NUL
ESC E
Set Line Spacing to n/72"
Set Vertical Tab Stops
Set Form Length in Inches
Set Form Length in Lines
Set Horizontal Tab Stops
Select Emphasized Mode
Load Form
ESC EM n
ESC ESC n
ESC F
Select Software Interface n
Cancel Emphasized Mode
Select Double-Strike Mode
Cancel Double-Strike Mode
Printing of Low Symbols
Variable Distance Line Feed
60 DPI Graphics
ESC G
ESC H
ESC I n
ESC J n
ESC K n1 n2 data
ESC L n1 n2 data
ESC M
120 DPI Graphics
Select 12 CPI
ESC N n
ESC O
Set Perforation Skip
Cancel Perforation Skip
Select 10 CPI
ESC P
ESC Q n
ESC R n
Set Right Margin
Select International Character Set
Select Subscript or Superscript Mode
Select Condensed Mode
Select Double-Wide Mode (one line)
Cancel Subscript and Superscript Mode
Unidirectional Mode
ESC S n
ESC SI
ESC SO
ESC T
ESC U n
ESC W n
ESC Y n1 n2 data
ESC Z n1 n2 data
ESC \ n1 n2
ESC g
Double-Wide Mode
High Speed 120 DPI Graphics
High Speed 240 DPI Graphics
Relative Horizontal Tab
Select 15 CPI
ESC j n
Variable Distance Reverse Line Feed
Select Font
ESC k n
ESC l n
Set Left Margin
ESC t n
Character Table (Italic vs. Extended)
Double-High Mode
ESC w n
ESC x n
Select Draft or Letter Quality
End of Text
ETX
FF
Form Feed
HT
Horizontal Tab
LF
Line Feed
100
Download from Www.Somanuals.com. All Manuals Search And Download.
C O N T R O L C O D E S A N D E S C A P E S E Q U E N C E S
SI
Select Condensed Mode
SO
Select Double-Wide Mode (one line)
Vertical Tab
VT
XOFF
Deselect Printer
IBM Proprinter Emulation
BEL
Bell
BS
Backspace
CAN
Cancel Line
CR
Carriage Return
DC2
Select 10 CPI
DC4
Cancel Double-Wide Mode (one line)
Underline Mode
ESC - n
ESC 0
Select 8 LPI
Set Line Spacing to 7/72"
Start Line Spacing
Set Line Spacing to n/216"
Set Top of Form
Automatic Line Feed
Select Character Set 2
Select Character Set 1
Select 12 CPI
ESC 1
ESC 2
ESC 3 n
ESC 4
ESC 5 n
ESC 6
ESC 7
ESC :
ESC A n
ESC B n1 n2 ... nx NUL
ESC C NUL n
ESC C n
ESC D n1 n2 ... nx NUL
ESC E
Set Line Spacing to n/72"
Set Vertical Tab Stops
Set Form Length in Inches
Set Form Length in Lines
Set Horizontal Tab Stops
Select Emphasized Mode
Select Software Interface n
Cancel Emphasized Mode
Select Double-Strike Mode
Cancel Double-Strike Mode
Select Print Mode
ESC ESC n
ESC F
ESC G
ESC H
ESC I n
ESC J n
ESC K n1 n2 data
ESC L n1 n2 data
ESC N n
ESC O
Variable Distance Line Feed
60 DPI Graphics
120 DPI Graphics
Set Perforation Skip
Cancel Perforation Skip
Deselect Printer
Reset Horiz. and Vertical Tab Stops
Select Subscript or Superscript Mode
Select Condensed Mode
Select Double-Wide Mode (one line)
Cancel Subscript and Superscript Mode
Unidirectional Mode
ESC Q n
ESC R
ESC S n
ESC SI
ESC SO
ESC T
ESC U n
101
Download from Www.Somanuals.com. All Manuals Search And Download.
C O N T R O L C O D E S A N D E S C A P E S E Q U E N C E S
ESC W n
Double-Wide Mode
ESC X n1 n2
Set Left and Right Margin
High Speed 120 DPI Graphics
High Speed 240 DPI Graphics
ESC Y n1 n2 data
ESC Z n1 n2 data
ESC [ @ n1 n2 m1 m2 m3 m4 Double-High Mode
IBM Proprinter Emulation (cont.)
ESC \ n1 n2
Print Characters
ESC ^ n
ETX
FF
Print Single Character
End of Text
Form Feed
HT
Horizontal Tab
LF
Line Feed
SI
Select Condensed Mode
Select Double-Wide Mode (one line)
Vertical Tab
SO
VT
LA-120/210 EMULATION
BEL
Bell
BS
Backspace
CR
Carriage Return
Control Sequence Introducer
Delete
CSI
DEL
ESC ( a
ESC 1
Select International Character Set
Set Horizontal Tab Stop
Clear All Horizontal Tab Stops
Set Vertical Tab Stop
Clear All Vertical Tab Stops
Line Feed
ESC 2
ESC 3
ESC 4
ESC D
ESC E
ESC ESC n
ESC H
ESC J
New Line
Select Software Interface n
Set Horizontal Tab Stop
Set Vertical Tab Stop
Control Sequence Introducer
Absolute Horizontal Tab
Relative Horizontal Tab
Printer Identification
Printer Identification
Absolute Vertical Tab
Relative Vertical Tab
Clear Horizontal Tab Stop
Clear Horizontal Tab Stop
Clear Vertical Tab Stop
ESC [
ESC [ n `
ESC [ n a
ESC [ c
ESC [ 0 c
ESC [ n d
ESC [ n e
ESC [ g
ESC [ 0 g
ESC [ 1 g
102
Download from Www.Somanuals.com. All Manuals Search And Download.
C O N T R O L C O D E S A N D E S C A P E S E Q U E N C E S
ESC [ 2 g
ESC [ 3 g
ESC [ 4 g
ESC [ 20 h
ESC [ 20 l
ESC [ n m
Clear All Horizontal Tab Stops
Clear All Horizontal Tab Stops
Clear All Vertical Tab Stops
Select Automatic Carriage Return
Cancel Automatic Carriage Return
Select Graphic Rendition
ESC [ n1 ; n2 r
Set Top and Bottom Margins
Set Left and Right Margin
Set Form Length in Lines
Set Horizontal Tab Stops
Set Vertical Tab Stops
Set Character Spacing
Set Line Spacing
End of Text
ESC [ n1 ; n2 s
ESC [ n t
ESC [ n1 ; n2 ; ... nx u
ESC [ n1 ; n2 ; ... nx v
ESC [ n w
ESC [ n z
ETX
FF
Form Feed
HT
Horizontal Tab
HTS
Set Horizontal Tab Stop
Line Feed
IND
LF
Line Feed
NEL
VT
New Line
Vertical Tab
VTS
Set Vertical Tab Stop
Simple TTY Emulation
BEL
Bell
BS
Backspace
CR
ESC ESC n
ETX
FF
HT
LF
VT
Carriage Return
Select Software Interface n
End of Text
Form Feed
Horizontal Tab
Line Feed
Vertical Tab
103
Download from Www.Somanuals.com. All Manuals Search And Download.
C O N T R O L C O D E S A N D E S C A P E S E Q U E N C E S
Printek Emulation
BEL
Bell
BS
Backspace
CR
DC3
Carriage Return
Deselect Printer
ESC # m n1 n2 data
ESC %
m DPI Graphics
Line Feed Boundary
m DPI Graphics
ESC * m n1 n2 data
ESC @
Reset
ESC A n
ESC B n
ESC C
Automatic Modes
Auto Cut Mode
Cut
ESC D n
ESC E n
ESC ESC n
ESC F n
ESC FF n
ESC G n
ESC H n1 n2
ESC HT n1 n2 ... nx NUL
ESC I n
ESC L n
ESC LF n
ESC Q n
ESC R
Double-Strike Mode
Emphasized Mode
Select Software Interface n
Select Font
Set Form Length in Lines
Modify Print Head Gap
Set Left and Right Margin
Set Horizontal Tab Stops
Set Print Head Force
Load Form
Set Line Spacing to n/288"
Select Font Quality
Reset Horiz. and Vertical Tab Stops
Select Script Modes
Set character Spacing
Unidirectional Mode
Set Top and Bottom Margins
Set Vertical Tab Stops
Double-Wide Mode
Print Single Character
Reverse Line Feed
Underline Mode
ESC S n
ESC SP n
ESC U n
ESC V n1 n2
ESC VT n1 n2 ... nx NUL
ESC W n
ESC \ n
ESC ^
ESC _ n
ETX
End of Text
FF
Form Feed
HT
Horizontal Tab
LF
Line Feed
VT
Vertical Tab
XOFF
Deselect Printer
104
Download from Www.Somanuals.com. All Manuals Search And Download.
ASCII CHARACTER TABLES
Epson FX Font Character Set
105
Download from Www.Somanuals.com. All Manuals Search And Download.
A S C I I C H A R A C T E R T A B L E S
PC Font Character Set
EBCDIC Font Character Set
106
Download from Www.Somanuals.com. All Manuals Search And Download.
A S C I I C H A R A C T E R T A B L E S
PC Latin 2 (Slavic) Font Character Set
OCR-A Font Character Set
107
Download from Www.Somanuals.com. All Manuals Search And Download.
A S C I I C H A R A C T E R T A B L E S
OCR-B Font Character Set
ML Euro (858)
108
Download from Www.Somanuals.com. All Manuals Search And Download.
ML (850)
109
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Print Speeds
Text Modes
Fast Draft
Draft
Speed
800 cps
600 cps
Fast Draft High Impact 400 cps
Draft High Impact
Letter Quality
Optical Quality
300 cps
150 cps
100 cps
Graphics Modes
8 Wire Graphics
8 Wire Fast Graphics
9 Wire Graphics
9 Wire Fast Graphics
Speed (up to) *
19,200 dps
25,600 dps
21,600 dps
28,800 dps
Character Matrix
Fast Draft 7x9 in 9x9 cell.
Draft 9x9 in 12x9 cell.
Letter Quality 18x18 in 24x18 cell.
Optical Quality 27x18 in 36x18 cell.
Graphics Density
60 to 240 dpi horizontally x 72 dpi vertically. *
111
Download from Www.Somanuals.com. All Manuals Search And Download.
S P E C I F I C A T I O N S
Character Sets
Epson FX fast draft, draft and letter quality.
IBM Proprinter fast draft, draft and letter quality.
EBCDIC fast draft, draft and letter quality.
Latin II (Slavic) fast draft, draft, and letter quality.
OCR-A optical quality.
OCR-B optical quality.
Multilingual (Code Page 858) fast draft, draft and letter quality.
Multilingual (Code Page 850) fast draft, draft and letter quality.
Character Spacing
5, 6, 6.7, 7.5, 8.4, 8.6, 10, 12, 13.3, 15, 16.7, 17.1, and 20 cpi. *
Line Spacing
6 lpi, 8 lpi, or programmable in 1/216th or 1/288th of an inch. *
Line Length
13.6 inches.
Control Code And Escape Sequence Emulations
Genicom 3840
Genicom 3410
ANSI X3.64
Epson FX
IBM Proprinter
DEC LA-120 and LA-210
Simple TTY
Printek
Basic Bar Code
Paper Handling
112
Download from Www.Somanuals.com. All Manuals Search And Download.
S P E C I F I C A T I O N S
Bottom tractor feed with pinch roller exit.
Straight paper path with zero waste tear off.
Paper width: 2.5 to 15 inches.
Paper Slew Rate: 16 inches per second.
Ribbon
23,000,000 character, mobius loop cartridge.
Special Forms Handling Features
Print up to six part forms (.025" maximum thickness).
Easy access to tractors.
Front panel and host form selection.
Automatic head gap.
Paper out sensing.
Paper motion sensing.
Paper edge sensing.
Page reprint.
Automatic path switching for same form in more than one path.
Nonvolatile memory for ten form setups. Parameters for each form include:
custom form name, tractor path (only in FormsMaster 8003se), automatic
forms cutting (only if FormsCutter is installed), cpi, left margin, right margin,
lpi, form length, top margin, bottom margin, font, character impact mode,
language*, slashed or nonslashed zero, and unidirectional printing.
Computer Interface
Parallel, serial, or optional LAN interface (if installed).
Centronics compatible Parallel.
Asynchronous RS-232: 110 to 9600 baud; Even, Odd, or No parity; 7 or
8 data bits; 1 or 2 stop bits; XON/XOFF, ETX/ACK, and Hardware
handshake.
Input Buffer Size: 32K bytes.
113
Download from Www.Somanuals.com. All Manuals Search And Download.
S P E C I F I C A T I O N S
Operator Controls/Indicators
Normal Operating Mode
Indicators: Online/Status LED; 2x16 character LCD for current form
selection (and paper path in FormsMaster 8003se), on/off line
status and error descriptions.
Controls: Online, Form Feed/Load, Form Select/Unload, Align Print,
and enter Setup.
Setup Mode
Indicators:
Controls:
Online/Status LED indicates Setup mode is active.
Menu, Submenu, Items, Values.
Setup Features: Forms Menu for setting form and printing parameters,
Interface Menu for setting all I/O parameters, Option
Menu for setting/installing option parameters, Test Menu,
and Security Menu for disabling changes to interface,
form, and option settings.
Reliability
Unit automatically measures and sets operating parameters each time unit is
powered on.
Forced air cooling.
MTBF 10,000 hours on electronics, 100% duty cycle.
Print head life of 500,000,000 draft mode (or equivalent) characters.
Printer life excluding print head of 1,000,000 pages.
Warranty
Printer:
One year limited warranty for defects in materials and/or
workmanship.
Print Head: 500 million draft equivalent character life. One year limited
warranty for defects in materials and/or workmanship. Limited
114
Download from Www.Somanuals.com. All Manuals Search And Download.
S P E C I F I C A T I O N S
print head warranty may be extended to a two years with the
use of only Printek® brand ribbons.
Environmental Specifications
Power requirements: 100-250 VAC, 50-60Hz Autoswitching
Power consumption: 18 W non-printing, 60 W printing.
Energy Start Compliant
Heat Output: 205 Btu/Hr. Idle, 768 Btu/Hr. Printing.
Audible noise: £55 dBA when used with a
Printek FormsMaster 8000se print stand..
Operating Temperature: 50°F to 95°F.
Relative Humidity: 20% to 80% non-condensing.
Physical Size: 11.8" High x 26.25" Wide x 20.5" Deep.
Weight: 53 lbs (63 lbs shipping).
Options
Ethernet 10/100BaseT Print Server
Wirelest Ethernet Print Server
Imager or ImagerPlus Graphics Co-Processor
Paper Cutter
Setup Module
Print Stand
115
Download from Www.Somanuals.com. All Manuals Search And Download.
S P E C I F I C A T I O N S
* May be emulation dependent.
Specifications subject to change without notice.
116
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY OF TERMS
ANSI
American National Standards Institute.
ASCII
American Standard Code for Information
Interchange.
baud rate
binary
The bit rate at which characters are transmitted
over a serial interface.
Base two numbering system. Digits are
represented by the characters 0 and 1.
bit
A single binary digit.
control code
A single, non-printing character which is used
to control the configuration or operation of the
printer.
character pitch
The horizontal spacing of characters.
Measured in cpi.
cpi
Characters-per-inch.
cps
Characters-per-second.
current line
The line upon which the next character will be
printed.
current print position
default
The column on the current line where the next
character will be printed.
Value or configuration that is assumed when
the printer is turned on or reset.
DF
dpi
Draft Font.
Dots-per-inch. Generally used to refer to
graphics density or resolution.
117
Download from Www.Somanuals.com. All Manuals Search And Download.
G L O S S A R Y
draft
Refers to the draft font.
EBCDIC
Extended Binary Coded Decimal Interchange
Code.
escape sequence
String of characters beginning with the escape
(ESC) character which is used to control the
configuration or operation of the printer. The
characters which are part of this string are not
printed.
fast draft
FD
Refers to the fast draft font.
Fast Draft.
font
A group of characters of a given shape or style.
A superior line of serial matrix printers.
FormsMaster
hexadecimal
Base sixteen numbering system. Digits are
represented by the characters 0 through 9 and
A through F.
interface
Generally refers to the connection between the
printer and the host computer. May also be
used in reference to the user interface at the
control panel of the printer.
LCD
Liquid-Crystal Display.
Light-Emitting Diode.
LED
line pitch
The vertical spacing of characters. Measured
in lpi.
lpi
Lines-per-inch.
Letter Quality.
LQ
MSB
Most-significant bit or byte. In a character, this
refers to bit seven (of 0 to 7).
octal
Base eight numbering system. Digits are
represented by the characters 0 through 7.
118
Download from Www.Somanuals.com. All Manuals Search And Download.
G L O S S A R Y
offline
online
Refers to the state of the printer when the
ONLINE indicator is not solid green and the
printer does not respond to the host computer.
Refers to the state of the printer when the
ONLINE indicator is solid green and the printer
able to respond to the commands and text
received from the host computer.
OQ
Optical Quality.
parity
A method used for detecting errors within a
single character transmitted or received via an
interface.
reset
Initialization of various operating parameters of
the printer to the value or state assumed when
the printer is powered on (default value).
top of form
The vertical position where the first line is
printed on the paper. Also the position the
paper is advanced to when a form feed (FF)
character is received from the host or the
FORM FEED button is pressed on the printer's
control panel.
tractors
Devices which control the movement of the
paper through the printer.
119
Download from Www.Somanuals.com. All Manuals Search And Download.
|