INSTALLATION INSTRUCTIONS
GB-PLEN1
Equipment Enclosure for Plenum Ceilings
AUSTRALIA, NEW ZEALAND, OCEANIA
EUROPE
Swallow House,
NORTH AMERICA
3130 East Miraloma Avenue
Anaheim, CA 92806 USA
USA and Canada –
(DISTRIBUTOR)
P.O. Box 295
Shilton Industrial Estate,
Shilton, Coventry, England CV79JY
Phone: +44 (0) 2476 614700
Fax: +44 (0) 2476 614710
Mordialloc Victoria 3195
Australia
Phone: 039586 6330
Phone: 800-368-9700
Fax: 800-832-4888
Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044
©Premier Mounts 2008
9534-003-003-00
Download from Www.Somanuals.com. All Manuals Search And Download.
GB-PLEN1
Parts List
This accessory is shipped with all proper installation hardware and components. Make sure that none of these parts
are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the
installation and contact Premier Mounts (800-368-9700).
Mounting Rails (Qty 2)
Cover Lid (Qty 1)
GB-PLEN1 (Qty 1)
M5 x 10mm Phillips
Head Screw (Qty 10)
Padlock Hasp (Qty 1)
Installation Tools
Phillips Screwdriver
Installation Instructions
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
GB-PLEN1
The GB-PLEN1 is designed for use with either the PP-FCTA or PP-FCMA. After installing your
selected false-ceiling adapter, follow the instructions on the following pages to secure the GB-PLEN1.
GB-PLEN1 Installation with PP-FCTA
Mounting
Rails
PP-FCTA
Plate
Upper Adapter
Plate
Wing Nut
Upper Adapter
Plate
PP-FCTA
Step 1. Loosen the wing nuts (do not remove) on
Step 2. Slide
the
mounting
rails
the upper adapter plate.
(threaded holes facing up) between the
upper adapter plate and the PP-FCTA.
Wing nut
Slide Guide
Step 3. Determine final placement of the upper
adapter plate.
Step 4. Tighten the wing nuts.
All four wing nuts must be parallel with the
slide guide. If not, the Gear Box will not sit
correctly on the PP-FCTA (see illustration
arrow above).
Page 4
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
GB-PLEN1
You may wish to pre-install your electronic components inside the enclosure at this time. If so, make sure to leave the
mounting slots accessible.
Mounting
Points
M5 x 10mm Screws
Step 5. Locate the four (4) mounting holes
on the mounting rails.
Step 6. Align the mounting slots on the
GB-PLEN1 with the mounting holes on
the mounting rails.
Step 7. Use four (4) M5 x 10mm screws to attach
the GB-PLEN1 to the mounting rails.
Mounting
Rails
Installation Instructions
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
GB-PLEN1
If you did not pre-install electrical components,
then you may now install all power and signal
equipment. A qualified electrician should make any
power connections to the GB-PLEN1.
Padlock Hasp
(optional)
M5 x 10mm
Screws
Step 8. Place the padlock hasp on the inside of the
GB-PLEN1 (optional).
Completed Attachment
When attaching the padlock hasp, make sure
the flat side is resting against the inside wall
of the GB-PLEN1.
Step 9. Use two (2) M5 x 10mm Phillips screws to attach
the padlock hasp to the GB-PLEN1.
Step 10. Place the cover lid onto the GB-PLEN1 and
secure using four (4) M5 x 10mm screws and
tighten with a Phillips head screwdriver.
The cover lid may be mounted facing either
direction.
Cover Lid
Completed Installation
M5 x 10mm
Screws
Page 6
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
GB-PLEN1
The GB-PLEN1 is designed for use with either the PP-FCMA or PP-FCTA. After installing your
selected false-ceiling adapter, follow the instructions on the following pages to secure the GB-PLEN1.
GB-PLEN1 Installation with PP-FCMA
Mounting
Rails
Adapter Plate
Mounting Screw
Screwdriver
PP-FCMA
M5 x 10mm Screws
Step 1. Loosen the four (4) mounting screws that are
located on the underside of the PP-FCMA. Do not
completely remove these screws.
Step 2. Slide the mounting rails (threaded holes facing
up) between the adapter plate and the PP-FCMA.
Step 3. Once the mounting rails have been positioned,
tighten the mounting screws with the
screwdriver.
Step 4. Align the mounting slots on the GB-PLEN1 with
the mounting holes on the mounting rails.
Step 5. Use four (4) M5 x 10mm screws to attach the
GB-PLEN1 to the mounting rails.
Mounting
Rails
Installation Instructions
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
GB-PLEN1
Padlock Hasp
(optional)
If you did not pre-install electrical components,
then you may now install all power and signal
equipment. A qualified electrician should make any
power connections to the GB-PLEN1.
M5 x 10mm
Screws
Step 6. Place the padlock hasp on the inside of the
Completed Attachment
GB-PLEN1 (optional).
When attaching the padlock hasp, make sure
the flat side is resting against the inside wall
of the GB-PLEN1.
Step 7. Use two (2) M5 x 10mm Phillips screws to attach
the padlock hasp to the GB-PLEN1.
Step 8. Place the cover lid onto the GB-PLEN1 and
secure using four (4) M5 x 10mm screws and
tighten with a Phillips head screwdriver.
The cover lid may be mounted facing either
direction.
Cover Lid
Completed Installation
M5 x 10mm
Screws
Page 8
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
GB-PLEN1
Technical Specifications
All measurements are in inches(mm).
Installation Instructions
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
GB-PLEN1
Warranty
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of
the original owner of this product. The limited warranty is valid only for the original purchaser of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is
defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will
be shipped to you at no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DIS-
PLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN
PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER
MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUD-
ING BUT NOT LIMITED TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOV-
ING AND REPLACING DEFECTIVE PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to
the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original con-
sumer purchaser must accompany all warranty claims. Warranty claims must also include a description of the
problem, the purchaser’s name, address, and telephone number. General inquiries can be addressed to Premier
Mounts Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or by fax.
Premier Mounts
Attn: Warranty Claim
3130 East Miraloma Ave.
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
Page 10
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
|