IMPORTANT MANUAL
Do Not Throw Away
OWNER'S MANUAL
MODEL NUMBER:
WARNING:
Read the Owner's Manual and
follow all Warnings and Safety
Instructions. Failure to do so
can result in serious injury.
PR524
SNOW THROWER
421104 Rev 1 08.21.08 TH
Always Wear Eye Protection During Operation
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Whencleaning,repairingorinspectingthesnowthrower,
stoptheengineandmakecertainthecollector/impeller
and all moving parts have stopped. Disconnect the
spark plug wire and keep the wire away from the plug
to prevent someone from accidentally starting the en-
gine.
7. Do not run the engine indoors, except when starting
the engine and for transporting the snow thrower in or
out of the building. Open the outside doors; exhaust
fumes are dangerous.
16. Never touch a hot engine or muffler.
Clearing a Clogged Discharge Chute
Handcontactwiththerotatingimpellerinsidethedischarge
chute is the most common cause of injury associated with
snow throwers. Never use your hand to clean out the dis-
charge chute. To clear the chute:
1. SHUT THE ENGINE OFF!
2. Wait 10 seconds to be sure the impeller blades have
stopped rotating.
8. Exercise extreme caution when operating on slopes.
3. Always use a clean-out tool, not your hands.
9. Neveroperatethesnowthrowerwithoutproperguards,
and other safety protective devices in place and work-
ing.
Maintenance and Storage
1. Check shear bolts and other bolts at frequent intervals
for proper tightness to be sure the equipment is in safe
working condition.
10. Never direct the discharge toward people or areas
where property damage can occur. Keep children
and others away.
2. Never store the machine with fuel in the fuel tank
inside a building where ignition sources are present
such as hot water heaters, space heaters, or clothes
dryers. Allow the engine to cool before storing in any
enclosure.
3. Always refer to operator’s manual for important details
if the snow thrower is to be stored for an extended
period.
4. Maintain or replace safety and instruction labels, as
necessary.
5. Run the machine a few minutes after throwing snow
to prevent freeze-up of the collector/impeller.
11. Do not overload the machine capacity by attempting
to clear snow at too fast a rate.
12. Never operate the machine at high transport speeds
on slippery surfaces. Look behind and use care when
operating in reverse.
13. Disengage power to the collector/impeller when snow
thrower is transported or not in use.
14. Use only attachments and accessories approved by
the manufacturer of the snow thrower (such as wheel
weights, counterweights, or cabs).
15. Never operate the snow thrower without good visibility
or light. Always be sure of your footing, and keep a firm
hold on the handles. Walk; never run.
CONGRATULATIONS on your purchase of a new snow
thrower. Ithasbeendesigned,engineeredandmanufactured
to give best possible dependability and performance.
PRODUCT SPECIFICATIONS
Gasoline Capacity
and Type:
2.0 Quarts (2,27 Liters)
Unleaded Regular only
Should you experience any problem you cannot easily
remedy, please contact your nearest authorized service
center. We have competent, well-trained technicians and
the proper tools to service or repair this unit.
Oil Type
(API SG–SL):
SAE 30 (above 40°F)
SAE 5W-30 or 10W-30 (0° to +40°F)
SAE 0W-30 (below 0°F)
Please read and retain this manual. The instructions will
enable you to assemble and maintain your snow thrower
properly. Always observe the “SAFETY RULES”.
Oil Capacity:
21 Ounces (0,6 Liters)
Spark Plug:
Gap:
Champion RJ19LM
0.030" (0,762 mm)
SERIAL NUMBER: ___________________________
DATE OF PURCHASE: _______________________
THEMODELANDSERIALNUMBERSWILLBEFOUND
ONADECALATTACHEDTOTHEREAROFTHESNOW
THROWER HOUSING.
CUSTOMER RESPONSIBILITIES
•
•
Read and observe the safety rules.
Follow a regular schedule in maintaining, caring for
and using your snow thrower.
YOUSHOULDRECORDBOTHSERIALNUMBERAND
DATE OF PURCHASE AND KEEP IN A SAFE PLACE
FOR FUTURE REFERENCE.
•
Follow the instructions under “Maintenance” and “Stor-
age” sections of this owner’s manual.
TABLE OF CONTENTS
SAFETY RULES ........................................................ 2-3
MAINTENANCE SCHEDULE ..................................... 14
SERVICE AND ADJUSTMENTS........................... 16-18
STORAGE.............................................................. 18-19
TROUBLESHOOTING................................................ 19
REPAIR PARTS ..................................................... 20-35
WARRANTY................................................................ 36
PRODUCT SPECIFICATIONS...................................... 4
CUSTOMER RESPONSIBILITIES................................ 4
ASSEMBLY / PRE-OPERATION ............................... 5-7
OPERATION ............................................................ 8-13
MAINTENANCE..................................................... 14-15
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS PACKED SEPARATELY IN CARTON
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY / PRE-OPERATION
Read these instructions and this manual in its entirety
before you attempt to assemble or operate your new
snow thrower. Reading the entire manual will familiar-
ize you with the unit, which will assist you in assembly,
operation and maintenance of the product.
SPEED
CONTROL
ROD
PLASTIC TIE
Your new snow thrower has been assembled at the factory
with the exception of those parts left unassembled for ship-
ping purposes. All parts such as nuts, washers, bolts, etc.,
necessary to complete the assembly have been placed in
the parts bag. To ensure safe and proper operation of your
snow thrower, all parts and hardware you assemble must
be tightened securely. Use the correct tools as necessary
to ensure proper tightness.
UPPER
HANDLE
HANDLE
KNOB
LOWER
HANDLE
REMOVE SNOW THROWER FROM CARTON
1. Remove all accessible loose parts and parts boxes
from carton.
2. Cut down all four corners of carton and lay panels flat.
3. Removethetwo(2)screwssecuringtheaugerhousing
to the pallet.
4. Removeallpackingmaterialsexceptplastictieholding
speed control rod to lower handle.
5. Remove the two (2) plastic ties securing the upper
handle to the pallet.
6. Remove snow thrower from carton and check carton
thoroughly for additional loose parts.
FIG. 1
SPEED CONTROL ROD
HOW TO SET UP YOUR SNOW THROWER
TOOL BOX (See Fig. 10)
RETAINER
SPRING
A toolbox is provided on your snow thrower. The toolbox is
located on top of the belt cover. Store the extra shear bolts,
nuts and multi-wrench provided in parts bag in the toolbox.
NOTE: The multi-wrench may be used for assembly of the
chuterotatorheadtosnowthrowerandmakingadjustments
to the skid plates.
UNFOLD UPPER HANDLE
1. Raise upper handle to the operating position and
tighten handle knobs securely. Additional carriage
bolts, washers and handle knobs are in bag of parts.
Use to secure upper handle to lower handle. Install
in lower holes in handles.
SPEED
CONTROL
BRACKET
SPEED
CONTROL
LEVER
INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)
FIG. 2
1. Remove plastic tie securing rod to lower handle.
2. Insert rod into speed control bracket and secure with
retainer spring.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY / PRE-OPERATION
INSTALL TRACTION DRIVE CONTROL ROD
(See Figs. 3 and 4)
The traction drive control rod has the long loop on the end
of the spring as shown.
1. Slide rubber sleeve up rod and hook end of spring into
pivot bracket with loop opening down as shown.
2. With top end of rod positioned under left side of control
panel, pushroddownandinserttopendofrodintohole
in drive control bracket. Secure with retainer spring.
INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)
The auger control rod has the short loop on the end of the
spring as shown.
1. Slide rubber sleeve up rod and hook end of spring into
control arm with loop opening up as shown.
2. With top end of rod positioned under right side of
control panel, push down on rod and insert end of rod
into hole in auger control bracket. Secure with retainer
spring.
TRACTION DRIVE
CONTROL ROD
AUGER
CONTROL
ROD
RUBBER
SLEEVE
RUBBER
SLEEVE
CONTROL
ARM
LOOP OPEN-
ING DOWN
LOOP
OPENING
UP
PIVOT
BRACKET
FIG. 5
FIG. 3
AUGER CONTROL ROD
AUGER
CONTROL
LEVER
TRACTION DRIVE
CONTROL LEVER
RETAINER
SPRING
RETAINER
SPRING
TRACTION
DRIVE
CONTROL
ROD
DRIVE
CONTROL
BRACKET
AUGER
CONTROL
BRACKET
FIG. 4
FIG. 6
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY / PRE-OPERATION
INSTALL DISCHARGE CHUTE / CHUTE ROTATOR
HEAD (See Fig. 7)
NOTE: The multi-wrench provided in your parts bag may
be used to install the chute rotator head.
SPRING
1/4-20
SHOULDER
BOLT
CHUTE
DEFLECTOR
HOOK
1. Place discharge chute assembly on top of chute base
with discharge opening toward front of snow thrower.
2. Positionchuterotatorheadoverchutebracket. Ifneces-
sary,rotatechuteassemblytoalignsquareandpinonun-
dersideofchuterotatorheadwithholesinchutebracket.
3. With chute rotator head and chute bracket aligned,
position chute rotator head on pin and threaded stud
of mounting bracket.
BETWEEN HEX
NUTS
NYLON
WASHER
ON CHUTE
ROTATER HEAD
1/4-20
LOCKNUT
5/16-18
CARRIAGE
BOLT
4. Install 3/8 washer and locknut on threaded stud and
tighten securely.
CABLE
EYELET
CHUTE
ROTATOR
HEAD
REMOTE
3/8 LOCKNUT
3/8 WASHER
CABLE
BRACKET
5/16-18
LOCKNUT
FIG. 8
PIN
THREADED
STUD
ROTATOR HEAD
MOUNTING
ALIGN BEFORE
TIGHTENING LOCKNUT
CHUTE
BRACKET
BRACKET
FIG. 7
CHUTE DEFLECTOR
CONTROL LEVER
INSTALL CHUTE DEFLECTOR REMOTE CONTROL
(See Figs. 8 and 9)
FIG. 9
1. Install remote cable bracket to discharge chute with
5/16-18 carriage bolt and 5/16-18 locknut as shown.
Tighten securely.
CHECK TIRE PRESSURE
Thetiresonyoursnowthrowerwereoverinflatedatthefac-
tory for shipping purposes. Correct and equal tire pressure
is important for best snow throwing performance.
2. Install remote cable eyelet to chute deflector with
1/4-20 shoulder bolt, nylon washer and 1/4-20 locknut
as shown. Tighten securely.
•
Reduce tire pressure to 14-17 PSI (19-24.5 N-m).
3. Install spring hooks between hex nuts on chute rotater
head and into hole in chute deflector as shown.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
KNOW YOUR SNOW THROWER
READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare
the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save
this manual for future reference.
These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand
their meaning.
PRIMER
DANGER
OR WARNING
READ AND FOLLOW ALL SAFETY INFORMATION
AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT.
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
FORWARD REVERSE
IGNITION KEY.
INSERT TO START
AND RUN,
PULL OUT TO STOP.
DISENGAGED
ENGAGED
SNOW
TRACTION
DISCHARGE
DRIVE CONTROL
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
AUGER
DISCHARGE CHUTE CONTROL LEVER
SPARK
PLUG
ENGINE OIL CAP
CONTROL
LEVER
WITH DIPSTICK
SAFETY
IGNITION
KEY
DEFLECTOR REMOTE
DRIVE SPEED
CONTROL LEVER
CONTROL LEVER
GASOLINE
FILLER
CAP
CHUTE
DEFLECTOR
CHOKE
CON-
TROL
FUEL
SHUT-OFF
VALVE
TRACTION
DRIVE
CONTROL
LEVER
THROTTLE
/ ENGINE
CONTROL
DISCHARGE
CHUTE
RECOIL
STARTER
HANDLE
PRIMER
OIL DRAIN PLUG
CLEAN-OUT TOOL
HANDLE
KNOB
MUFFLER
TOOLBOX
NOTE: ITEMS ABOVE
ARE SHOWN IN
THEIR TYPICAL
LOCATION ON THE
ENGINE. ACTUAL
LOCATION MAY VARY
WITH THE ENGINE
ON YOUR UNIT.
SKID PLATE
AUGERS
FIG. 8
MEETS A.N.S.I. SAFETY REQUIREMENTS
Our snow throwers conform to the standards of the American National Standards Institute.
Throttle/engine control - used to select either FAST or
SLOW engine speed and to STOP the engine.
Toolbox - used to store spare shear bolts, locknuts and
wrench.
Traction drive control lever - used to engage power-pro-
pelled forward or reverse motion of snow thrower.
Safety ignition key - must be inserted for the engine to
start and run. Remove when snow thrower is not in use.
Auger control lever - used to engage auger motion (throw
Recoil starter handle - used for starting the engine.
snow).
Primer - pumps additional fuel from the carburetor to the
cylinder for use when starting a cold engine.
Discharge chute control lever - used to change the di-
rection the snow is thrown.
Choke control - used for starting a cold engine.
Skid plate - used to adjust height of scraper bar from the
ground.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
The operation of any snow thrower can result
TO USE CHOKE CONTROL (See Fig. 11)
in foreign objects thrown into the eyes, which
canresultinsevereeyedamage. Alwayswear
safety glasses or eye shields while operating
your snow thrower or performing any adjust-
The choke control is located on the engine. Use the choke
control whenever you are starting a cold engine. Do not
use to start a warm engine.
00155
•
To engage choke, turn knob clockwise. Slowly turn
knob counterclockwise to disengage.
ments or repairs. We recommend standard safety glasses
or a wide vision safety mask worn over spectacles.
HOW TO USE YOUR SNOW THROWER
Know how to operate all controls before adding fuel or
attempting to start the engine.
OFF
FULL
STOPPING
TRACTION DRIVE
•
Release traction drive control lever to stop the forward
or reverse movement of the snow thrower.
AUGER
FIG. 11
•
Release the auger control lever to stop throwing snow.
TO CONTROL SNOW DISCHARGE (See Fig. 14)
ENGINE
WARNING: Snow throwers have ex-
posed rotating parts, which can cause
severe injury from contact, or from ma-
terial thrown from the discharge chute.
Keep the area of operation clear of all
persons, small children and pets at all
times including startup.
1. Move throttle control to “STOP” position.
2. Remove (do not turn) safety ignition key to prevent
unauthorized use.
NOTE: Never use choke to stop engine.
TO USE FUEL SHUT-OFF VALVE (See Fig. 9)
The fuel shut-off valve is located beneath the fuel tank on
the engine. Always operate the snow thrower with the fuel
shut-off valve in the OPEN position.
WARNING: If the discharge chute or
augerbecomeclogged,shut-offengine
andwaitforallmovingpartstostop.Use
the clean-out tool, NOT YOUR HANDS,
to unclog the chute and/or auger.
TheDIRECTIONinwhichsnowistobethrowniscontrolled
by the discharge chute control lever.
OFF
•
To change the discharge chute position, press down-
ward on discharge chute control lever and move lever
left or right until chute is in desired position. Be sure
lever springs back and locks into desired position.
OPEN
The DISTANCE that snow is thrown is controlled by the
position of the chute deflector. Set the deflector low to
throw snow a short distance; set the deflector higher to
throw snow farther.
FIG. 9
TO USE THROTTLE CONTROL (See Fig. 10)
Thethrottlecontrolislocatedontheengine.Alwaysoperate
the snow thrower with the engine at full throttle. Full throttle
offers the best snow thrower performance.
•
Press downward on chute deflector control lever and
moveleverforwardtolowerthedeflectoranddecrease
the distance. Move lever back to raise the deflector
and increase the distance. Be sure lever springs back
and locks into desired position.
FAST
TO THROW SNOW (See Fig. 14)
The auger rotation is controlled by the auger control lever
located on the right side handle.
•
Squeeze auger control lever to handle to engage the
auger and throw snow.
•
Release the auger control lever to stop throwing snow.
SLOW
FIG. 10
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO MOVE FORWARD AND BACKWARD (See Fig. 16)
DISCHARGE CHUTE
CONTROL LEVER
SELF-PROPELLING, forward and reverse movement of
the snow thrower, is controlled by the traction drive control
lever located on the left side handle.
•
Squeezetractiondrivecontrollevertohandletoengage
the drive system.
•
Release traction drive control lever to stop the forward
or reverse movement of the snow thrower.
SPEED and DIRECTION are controlled by the drive speed
control lever.
•
•
Press downward on the speed control lever and move
lever to desired position BEFORE engaging the trac-
tion drive control lever. Be sure lever springs back and
locks into desired position.
CHUTE DEFLECTOR
REMOTE CONTROL LEVER
FIG. 14
CAUTION: Do not move speed control lever
when traction drive control lever is engaged.
Damage to the snow thrower can result.
USING THE CLEAN-OUT TOOL (See Fig. 15)
In certain snow conditions, the discharge chute may be-
come clogged with ice and snow. Use the clean-out tool to
dislodge this blockage.
Slower speeds are for heavier snow and faster speeds
are for light snow and transporting the snow thrower. It
is recommended that you use a slower speed until you
are familiar with the operation of the snow thrower.
When cleaning, repairing, or inspecting, make
certain all controls are disengaged and the
auger/impeller and all moving parts have
stopped. Disconnect the spark plug wire and
keep the wire away from the spark plug to pre-
vent accidental starting.
TRACTION DRIVE
CONTROL LEVER
•
•
Releasetheaugercontrolleverandshutofftheengine.
Removetheclean-outtoolfromit'smountingclip. Grasp
the tool firmly by the handle and push and twist the tool
into the discharge chute to dislodge the blockage.
Afterthepackedsnowhasbeendislodged,returntheclean-
out tool to it's mounting clip by pushing it into the clip.
•
Makesurethedischargechuteispointedinasafedirec-
tion(novehicles,buildings,people,orotherobjectsare
inthedirectionofdischarge)beforerestartingtheengine.
DRIVE SPEED
CONTROL LEVER
•
Restart the engine, then squeeze the auger control
lever to the handle to clear snow from the auger hous-
ing and the discharge chute.
FIG. 16
DISCHARGE CHUTE
CLEAN-OUT
TOOL
MOUNTING
CLIP
FIG. 15
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO ADJUST SKID PLATES (See Fig. 17)
BEFORE STARTING THE ENGINE
CHECK ENGINE OIL LEVEL (See Fig. 18)
NOTE:Thewrenchprovidedinyourpartsbagmaybeused
to adjust the skid plates.
The engine on your snow thrower has been shipped, from
the factory, already filled with oil.
1. Check engine oil with snow thrower on level ground.
2. Remove oil fill cap/dipstick and wipe clean, reinsert
the dipstick and screw tight, wait for a few seconds,
remove and read oil level. If necessary, add oil until
“FULL” mark on dipstick is reached. Do not overfill.
Skid plates are located on each side of the auger housing
and adjust the clearance between the scraper bar and the
ground surface. Adjust skid plates evenly to proper height
for current surface conditions. For removal of snow in
normal conditions, such as a paved driveway or sidewalk,
place skid plates in the highest position (lowest scraper
clearance) to give a 1/8" clearance between the scraper
bar and the ground. Use a middle position if the surface
to be cleared is uneven.
•
To change engine oil, see “TO CHANGE ENGINE OIL”
in the Maintenance section of this manual.
NOTE: It is not recommended to operate the snow thrower
overgravelorrockysurfaces.Objectssuchasgravel,rocks
or other debris, can easily be picked up and thrown by the
impeller, which can cause serious personal injury, property
damage or damage to the snow thrower.
ADD GASOLINE (See Fig. 18)
•
Fill fuel tank to bottom of tank filler neck. Do not over-
fill. Use fresh, clean, regular unleaded gasoline with
a minimum of 87 octane. Do not mix oil with gasoline.
Purchase fuel in quantities that can be used within 30
days to assure fuel freshness.
•
If snow thrower must be operated over gravel surface,
use extra caution and be sure skid plates are adjusted
to lowest (highest scraper clearance) position.
WARNING: Wipe off any spilled oil or
fuel. Do not store, spill or use gasoline
near an open flame.
1. Shut off engine and wait for all moving parts to stop.
2. Adjust skidplatesbylooseningthehexnuts, thenmov-
ing skid plate to desired position. Be sure both plates
are adjusted evenly. Tighten securely.
CAUTION: Alcohol blended fuels (called
gasohol or using ethanol or methanol) can at-
tract moisture which leads to separation and
formation of acids during storage. Acidic gas
can damage the fuel system of an engine while
in storage. To avoid engine problems, the fuel
system should be emptied before storage of
30 days or longer. Drain the gas tank, start
the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season. SeeStorageInstructionsforadditional
information. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur.
HIGH POSITION
(LOW GROUND
CLEARANCE)
AUGER
HOUSING
SCRAPER BAR
HEX
SKID PLATE
NUTS
LOW POSITION (HIGH GROUND CLEARANCE)
FIG. 17
SCRAPER BAR
CHOKE CONTROL
THROTTLE PRIMER
ENGINE OIL
FILL CAP /
DIPSTICK
The scraper bar is not adjustable, but is reversible. After
considerable use it may become worn. When it has worn
almost to the edge of the housing, it can be reversed,
providing additional service before requiring replacement.
Replace a damaged or worn scraper bar.
SAFETY
IGNITION
KEY
GASOLINE
FILLER CAP
FUEL SHUT-
OFF VALVE
RECOIL
STARTER
HANDLE
NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.
FIG. 18
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TO START ENGINE
•
SNOW THROWING TIPS
Be sure fuel shut-off valve is in the “OPEN” position.
•
Always operate the snow thrower with the engine at
full throttle. Full throttle offers the best performance.
Your snow thrower engine is equipped with a recoil starter.
COLD START
1. Insert safety ignition key (packed separately in parts
bag)intoignitionslotuntilitclicks. DONOTturnthekey.
Keep the extra safety ignition key in a safe place.
•
Go slower in deep, freezing or heavy wet snow. Use
the drive speed control, NOT the throttle, to adjust
speed.
•
•
It is easier and more efficient to remove snow imme-
diately after it falls.
The best time to remove snow is the early morning. At
this time the snow is usually dry and has not been ex-
posed to the direct sun and warming temperatures.
2. Place throttle control in “FAST” position.
3. Rotate choke control to “FULL” position.
4. Push the primer four (4) times if the temperature is
below 15°F, or two (2) times if temperature is between
15° and 50°F. If temperature is above 50°F, priming is
not necessary.
•
Slightly overlap each successive path to ensure all
snow will be removed.
•
•
Throw snow downwind whenever possible.
NOTE: Over priming may cause flooding, preventing the
engine from starting. If you do flood the engine, wait a few
minutes before attempting to start and DO NOT push the
primer.
5. Pull recoil starter handle quickly. Do not allow starter
rope to snap back.
6. Whentheenginestarts,releasetherecoilstarterhandle
and slowly move the choke control to the “OFF” posi-
tion.
Adjust the skid plates to proper height for current snow
conditions. See “TO ADJUST SKID PLATES” in this
section of this manual.
•
For extremely heavy snow, reduce the width of snow
removal by overlapping previous path and moving
slowly.
•
•
•
Keep engine clean and clear of snow during use. This
will help air flow and extend engine life.
Aftersnow-throwingiscompleted,allowenginetorunfor
a few minutes to melt snow and ice off the engine.
Allow the engine to warm up for a few minutes. Engine will
not develop full power until it has reached normal operat-
ing temperature.
Clean the entire snow thrower thoroughly after each
use and wipe dry so it is ready for next use.
WARM START
Follow the steps above, keeping the choke in the “OFF”
position. DO NOT push the primer.
WARNING: Do not operate snow
throwerifweatherconditionsimpairvis-
ibility. Throwing snow during a heavy,
windysnowstormcan blind you and be
hazardous to the safe operation of the
snow thrower.
BEFORE STOPPING
Run the engine for a few minutes to help dry off any mois-
ture on the engine.
IF RECOIL STARTER HAS FROZEN
If the recoil starter has frozen and will not turn the engine,
proceed as follows:
1. Grasp the recoil starter handle and slowly pull as much
rope out of the starter as possible.
2. Release the recoil starter handle and let it snap back
against the starter.
If the engine still fails to start, repeat the above steps.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
GENERAL RECOMMENDATIONS
LUBRICATION CHART
Thewarrantyonthissnowthrowerdoesnotcoveritemsthat
have been subjected to operator abuse or negligence. To
receivefullvaluefromthewarranty,operatormustmaintain
snow thrower as instructed in this manual. Some adjust-
mentswillneedtobemadeperiodicallytoproperlymaintain
your snow thrower. All adjustments in the Service and
Adjustments section of this manual should be checked at
least once each season.
SAE 5W-30 Motor Oil
See “ENGINE”
in Maintenance
section
General
Purpose
Grease
•
Once a year, you should replace the spark plug and
check belts for wear. A new spark plug will help your
engine run better and last longer.
Pivot
points
•
Follow the maintenance schedule in this manual.
NOTE: Use only Original Equipment Manufacturer (OEM)
parts to service this unit. Failure to do so can cause the unit
to malfunction and pose a risk of injury to the operator.
BEFORE EACH USE
1. Check engine oil level.
2. Check for loose fasteners.
3. Checkcontrolstobesuretheyarefunctioningproperly.
LUBRICATION
Keep your snow thrower well lubricated
(See “LUBRICATION CHART”).
Auger
grease fittings
Engine oil
SNOW THROWER
Always observe the safety rules when performing any
maintenance.
V-BELTS
Check V-belts for deterioration and wear after every 50
hours of operation and replace if necessary. The belts
are not adjustable. Replace belts if they begin to slip from
wear. (See “TO REMOVE BELT COVER” in the Service
and Adjustments section of this manual).
TIRES
•
Maintain proper air pressure in both tires (14–17 P.S.I.
/ 19-24.5 N-m).
•
Keeptiresfreeofgasolineandoil,whichcanharmrubber.
TheV-beltsonyoursnowthrowerareofspecialconstruction
andshouldbereplacedbyoriginalequipmentmanufacturer
(OEM)beltsavailablefromyournearestdealer.Usingother
than OEM belts can cause personal injury or damage to
the snow thrower.
NOTE: To seal tire punctures and prevent flat tires due to
slow leaks, tire sealant may be purchased from your local
parts dealer. Tire sealant also prevents tire dry rot and
corrosion.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
AUGER GEAR CASE
•
•
•
Oil will drain more freely when warm.
Catch oil in a suitable container.
The gear case was filled with lubricant to the proper
level at the factory. The only time the lubricant needs
attention is if service has been performed on the gear
case.
NOTE: The left side wheel may be removed from snow
thrower for easier access to the oil drain plug and place-
ment of a suitable container. The unit tilted, resting on the
frame with the left wheel removed, will help drain any oil
trapped inside the engine. (See “TO REMOVE WHEELS”
in the Service and Adjustments section of this manual).
•
If lubricant is required, use only Ronex ED #1
grease.
TRACTION DRIVE SYSTEM
1. Remove safety ignition key and disconnect spark plug
wire from spark plug. Place wire where it cannot come
in contact with spark plug.
DO NOT lubricate the drive components inside the snow
thrower. The sprockets, hex shafts, drive disc and friction
wheel require no lubrication. The bearings and bushings
are lifetime lubricated and require no maintenance.
2. Clean area around drain plug.
3. Remove drain plug and drain oil in a suitable container.
4. Install drain plug and tighten securely.
5. Wipe off any spilled oil from snow thrower and engine.
6. Install left wheel (if removed for draining oil). Be sure to
install klick pin into proper hole in wheel axle (See “TO
REMOVE WHEELS” in the Service and Adjustments
section of this manual).
7. Remove oil fill cap/dipstick. Be careful not to allow dirt
to enter the engine.
CAUTION:Anylubricatingoftheabovecompo-
nents can cause contamination of the friction
wheel and damage to the drive system of your
snow thrower.
ENGINE
See engine manual.
LUBRICATION
8. Refill engine with oil through oil dipstick tube. Pour
slowly. Do not overfill. For approximate capacity see
“PRODUCTSPECIFICATIONS”sectionofthismanual.
Use only high quality detergent oil rated with API service
classification SG–SL. Select the oil's SAE viscosity grade
according to your expected operating temperature.
9. Use gauge on oil fill cap/dipstick for checking level. Be
sure dipstick cap is tightened securely for accurate
reading. Keep oil at “FULL” line on dipstick.
10. Wipe off any spilled oil.
MUFFLER
Inspect and replace corroded muffler as it could create a
fire hazard and/or damage.
SPARK PLUG
Replacesparkplugatthebeginningofeachseasonorafter
every100hoursofoperation,whicheveroccursfirst. Spark
plug type and gap setting are shown in the “PRODUCT
SPECIFICATIONS” section of this manual.
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)
improve starting in cold weather, these multi-viscosity oils
will result in increased oil consumption when used above
32°F. Check your engine oil level more frequently to avoid
possible engine damage from running low on oil.
CLEANING
IMPORTANT: For best performance, keep snow thrower
housing free of any dirt or trash. Clean the outside of your
snow thrower after each use.
Changetheoilafterevery25hoursofoperationoratleastonce
ayearifthesnowthrowerisnotusedfor25hoursinoneyear.
Checkthecrankcaseoillevelbeforestartingtheengineand
after each five (5) hours of continuous use. Tighten oil fill
cap / dipstick securely each time you check the oil level.
WARNING: Removesafetyignitionkey
and disconnect spark plug wire from
spark plug. Place wire where it cannot
come in contact with spark plug.
TO CHANGE ENGINE OIL
Determine temperature range anticipated before next oil
change.AlloilmustmeetAPIserviceclassificationSG–SL.
•
•
Keepfinishedsurfaces/wheelsfreeofgasoline,oil,etc.
•
Be sure snow thrower is on level surface.
We do not recommend using a garden hose to clean
yoursnowthrowerunlesstheelectricalsystem,muffler
and carburetor are covered to keep water out. Water
in engine can result in shortened engine life.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
WARNING: To avoid serious injury, before performing any service or adjustments:
1. Be sure throttle is in STOP position.
2. Remove safety ignition key.
3. Make sure the augers and all moving parts have completely stopped.
4. Disconnect spark plug wire from spark plug and place wire where it cannot contact plug.
3. Align holes in impeller hub with holes in impeller shaft
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear
bolts. Install 1/4-20 locknuts and tighten securely.
SNOW THROWER
TO ADJUST SNOW THROWER HEIGHT
See “TO ADJUST SKID PLATES” and “SCRAPER BAR”
in the Operation section of this manual.
CAUTION: Do not substitute. Use only original
equipment capscrew/shear bolts as supplied
with your snow thrower.
CHUTE DEFLECTOR
The chute deflector, attached to the top of the discharge
chute, is provided to direct discharging snow away from
the operator. If the deflector becomes damaged, it should
be replaced.
4. Insertsafetyignitionkeyandreconnectsparkplugwire
to spark plug.
1/4-20
LOCKNUT
1/4-20 x 1-5/8
CAPSCREW /
SHEAR BOLT
1/4-20 x 2
SHOULDER /
SHEAR BOLT
WARNING: To avoid serious injury,
never operate your snow thrower with
the deflector removed or damaged.
IMPELLER HUB
SPACER
IMPELLER
SHAFT
•
Tochangedirectionand/ordistancesnowisdischarged,
see “TO CONTROL SNOW DISCHARGE” in the Op-
eration section of this manual.
SHEAR BOLTS (See Fig. 19)
AUGER SHEAR BOLTS
Both right and left-hand augers are secured to the auger
shaft with a shoulder/shear bolt and hex nut. Should a for-
eign object or ice become lodged in the augers, the shear
bolts are designed to break, preventing damage to any
other components. If one or both augers do not turn when
auger control lever is engaged, check to see if one or both
of the bolts have sheared. To replace the shear bolts:
1. Disengage all controls and move throttle control to
STOP position. Wait for all moving parts to stop.
2. Remove safety ignition key and disconnect spark plug
wire from spark plug. Place wire where it cannot come
in contact with spark plug.
AUGER
HUB
1/4-20
LOCKNUT
AUGER HUB
FIG. 19
AUGER SHAFT
TO REMOVE BELT COVER (See Fig. 20)
1. Remove the two screws securing belt cover to frame.
2. Remove belt cover.
3. Alignholeinaugerhubwithholeinaugershaftandinstall
anew1/4-20x2"shoulder/shearboltandspacer. Install
1/4-20 lock nut and tighten securely.
•
Replace belt cover by installing cover and screws and
tighten securely.
CAUTION: Do not substitute. Use only original
equipment shear bolts as supplied with your
snow thrower.
4. Insertsafetyignitionkeyandreconnectsparkplugwire
to spark plug.
IMPELLER SHEAR BOLTS
The impeller is secured to the impeller shaft with two (2)
capscrew/shearboltsandhexnuts. Shouldaforeignobject
or ice become lodged in the impeller, the capscrews are
designed to break, preventing damage to any other com-
ponents. If impeller does not turn when auger control lever
is engaged, check to see if the capscrews have sheared.
To replace the capscrew/shear bolts:
FRAME
BELT COVER
FIG. 20
SCREWS
1. Disengage all controls and move throttle control to
STOP position. Wait for all moving parts to stop.
2. Remove safety ignition key and disconnect spark plug
wire from spark plug. Place wire where it cannot come
in contact with spark plug.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
HINT: Insert a 3/8" drive ratchet (in the “ON” position) into
TO REPLACE BELTS (See Fig. 22)
the square hole in idler arm and rotate ratchet clockwise
to relieve tension.
The auger and traction drive belts are not adjustable. If the
belts are damaged or begin to slip from wear, they should
be replaced. It is recommended that the belt(s) be replaced
by a Sears service centre/department.
8. With tension relieved on idler, install new traction drive
belt around pulleys and inside belt keepers.
9. Placeaugerbeltaroundandinsidethegrooveofauger
pulley only.
NOTE: It is recommended that both the auger and traction
drive belt be replaced at the same time.
10. While your assistant slowly raises handles to rejoin
the auger housing and frame assembly, pull up on the
auger belt and squeeze sides together above pulley
so belt is fully seated in groove of pulley.
11. Move idler arm so it does not hit impeller pulley as you
bring snow thrower completely together and check
carefully for proper routing of belts. If auger belt has
becomedislodgedfromthepulley(bycatchingtheidler
arm bracket while bringing snow thrower together),
separate the snow thrower and repeat step 12. Belt
must be fully seated in pulley groove when bringing
the snow thrower together
12. Install the two (2) hex bolts and lock washers and
tighten securely.
13. INSTALLENGINEPULLEY-Placebeltinpulleygroove
and slide pulley on crankshaft. Install flat washer,
lockwasher and bolt and tighten securely (41-47 N-m
torque). Make sure belt is inside belt keeper.
TheV-beltsonyoursnowthrowerareofspecialconstruction
andshouldbereplacedbyoriginalequipmentmanufacturer
(OEM) belts available from your nearest Sears service
centre/department. Using other than OEM belts can cause
personal injury or damage to the snow thrower.
WARNING: Belt replacement requires
separation of the snow thrower. While
separating the auger housing from the
frame assembly, it is important that an
assistantstandintheoperatingposition
andholdthesnowthrowerhandles.Se-
rious personal injury and/or damage to
theunitcouldoccurifthesnowthrower
should fall during the belt changing
process.
FRAME
ASSEMBLY
AUGER
HOUSING
14. INSTALL BELT COVER and two (2) screws. Tighten
securely.
15. INSTALL DISCHARGE CHUTE – See “INSTALL DIS-
CHARGE CHUTE / CHUTE ROTATER HEAD” in the
Assembly / Pre-Operation section of this manual.
BELT KEEPER
TRACTION DRIVE BELT
ENGINE
HANDLES
1. REMOVE GASOLINE FROM FUEL TANK - Drain
gasoline from fuel tank into a suitable container, out-
doors, away from fire or flame. Wipe up any spilled
gasoline.
2. REMOVE DISCHARGE CHUTE - Loosen locknut
securing chute rotator head to mounting bracket only
enough to allow chute rotator head to be raised and
discharge chute to be removed from snow thrower.
FLAT WASHER
PULLEY
LOCKWASHER
BOLT
AUGER
BELT
IDLER ARM
SQUARE
HOLE
3. REMOVE BELT COVER - See “TO REMOVE BELT
COVER” in this section of this manual.
4. REMOVEENGINEPULLEY-Removebolt,lockwasher
and flat washer securing pulley to engine crankshaft.
Remove outside (auger) pulley only from crankshaft.
CLUTCHING
IDLER ARM
BRACKET
AUGER
HOUSING
FRAME
AUGER PULLEY
BOLTS
5. SEPARATE SNOW THROWER - With your assistant
standing in the operating position holding the handles,
remove the two (2) bolts and lock washers holding
auger housing and frame together.
WARNING: As the last bolt is removed,
have your assistant carefully lower the
handles down to the ground.
FIG. 22
6. REMOVE AUGER BELT from around pulley.
7. RELIEVE TENSION ON TRACTION DRIVE BELT
IDLER and remove traction drive belt from around
pulleys.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND ADJUSTMENTS
TO REMOVE WHEELS (See Fig. 22)
Remove the klik pin and remove wheel from axle.
NOTE: To seal punctures or prevent flat tires due to slow
leaks, tire sealant may be purchased from your local parts
dealer. Tire sealant also prevents tire dry rot and corrosion.
•
IMPORTANT: When installing wheel, be sure to use the in-
nermost hole in axle and the wheel hub hole. To disengage
drive system from the wheels (for pushing or transporting
the snow thrower), remove klik pin from wheel hub and
insert pin into the outermost hole in axle only.
ENGINE
See engine manual.
CARBURETOR
Your carburetor is not adjustable. Engine performance
should not be affected at altitudes up to 7,000 feet (2,134
meters). If your engine does not operate properly due to
suspected carburetor problems, take your snow thrower
to a qualified service centre.
KLIK PIN
OUTER HOLE
ENGINE SPEED
Never tamper with the engine governor, which is factory set
for proper engine speed. Overspeeding the engine above
the factory high speed setting can be dangerous and will
void the warranty. If you think the engine-governed high
speed needs adjusting, contact a qualified service centre,
which has proper equipment and experience to make any
necessary adjustments.
INNER
HOLE
WHEEL
WHEEL HUB
FIG. 22
STORAGE
Immediately prepare your unit for storage at the end of the
season or if the unit will not be used for 30 days or more.
FUEL SYSTEM
IMPORTANT: It is important to prevent gum deposits from
forming in essential fuel system parts such as carburetor,
fuelhose,ortankduringstorage.Also,alcoholblendedfuels
(called gasohol or using ethanol or methanol) can attract
moisture which leads to separation and formation of acids
during storage. Acidic gas can damage the fuel system of
an engine while in storage.
WARNING: Never store the snow
throwerwithgasolineinthetankinside
a building where fumes may reach an
open flame, spark or pilot light as on a
furnace, water heater, clothes dryer or
gasappliance. Allowtheenginetocool
before storing in any enclosure.
•
•
•
Empty the fuel tank by starting the engine and letting
it run until the fuel lines and carburetor are empty.
Never use engine or carburetor cleaner products in the
fuel tank or permanent damage may occur.
SNOW THROWER
When snow thrower is to be stored for a period of time,
clean it thoroughly, remove all dirt, grease, leaves, etc.
Store in a clean, dry area.
1. Clean entire snow thrower (See “CLEANING” in the
Maintenance section of this manual).
2. Inspect and replace belts, if necessary (See “TO RE-
PLACEBELTS”intheServiceandAdjustmentssection
of this manual).
Use fresh fuel next season.
NOTE: Fuel stabilizer is an acceptable alternative in min-
imizing the formation of fuel gum deposits during storage.
Add stabilizer to gasoline in fuel tank or storage container.
Always follow the mix ratio found on stabilizer container.
Run engine at least 10 minutes after adding stabilizer to
allow the stabilizer to reach the carburetor. Do not drain the
gas tank and carburetor if using fuel stabilizer.
3. Lubricate as shown in the Maintenance section of this
manual.
4. Besurethatallnuts,bolts,screws,andpinsaresecurely
fastened. Inspect moving parts for damage, breakage
and wear. Replace if necessary.
ENGINE OIL
Drain oil (with engine warm) and replace with clean en-
gine oil. (See “ENGINE” in the Maintenance section of
this manual).
CYLINDER
1. Remove spark plug.
5. Touch up all rusted or chipped paint surfaces; sand
lightly before painting.
2. Pour one ounce (29 ml) of oil through spark plug hole
into cylinder.
ENGINE
See engine manual.
3. Pullrecoilstarterhandleslowlyafewtimestodistribute
oil.
4. Replace with new spark plug.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
STORAGE
•
Coveryoursnowthrowerwithasuitableprotectivecover
OTHER
thatdoesnotretainmoisture.Donotuseplastic.Plastic
cannotbreathe,whichallowscondensationtoformand
will cause your snow thrower to rust.
•
•
•
Remove safety ignition key; store it in a safe place.
Do not store gasoline from one season to another.
Replace your gasoline can if your can starts to rust.
Rust and/or dirt in your gasoline will cause problems.
IMPORTANT: Never cover snow thrower while engine/
exhaust area is still warm.
•
If possible, store your snow thrower indoors and cover
it to protect it from dust and dirt.
TROUBLESHOOTING
See appropriate section in manual unless directed to a qualified service centre/department.
PROBLEM
CAUSE
CORRECTION
Does not start
1. Fuel shut-off valve (if so
equipped) in OFF position.
2. Safety ignition switch OUT.
3. Out of fuel.
4. Throttle in STOP position.
5. Choke in OFF position.
6. Primer not depressed.
7. Engine is flooded.
8. Spark plug wire is
disconnected.
1. Turn fuel shut-off valve to OPEN position.
2. Push safety ignition switch IN.
3. Fill fuel tank with fresh, clean gasoline.
4. Move throttle to FAST position.
5. Move to FULL position.
6. Prime as instructed in the Operation section of this manual.
7. Wait a few minutes before restarting, DO NOT prime.
8. Connect wire to spark plug.
9. Bad spark plug.
10. Stale fuel.
11. Water in fuel.
9. Replace spark plug.
10. Empty fuel tank & carburetor, refill with fresh, clean gasoline.
11. Empty fuel tank & carburetor, refill with fresh, clean gasoline.
Loss of power
1. Spark plug wire loose.
2. Throwing too much snow.
3. Fuel tank cap is covered
with ice or snow.
1. Reconnect spark plug wire.
2. Reduce speed and width of swath.
3. Remove ice and snow on and around fuel tank cap.
4. Dirty or clogged muffler.
4. Clean or replace muffler.
Engine idles or
runs roughly
1. Choke is in FULL position.
2. Blockage in fuel line.
3. Stale fuel.
4. Water in fuel.
5. Carburetor is in need of
adjustment or overhaul.
1. Move choke to OFF position.
2. Clean fuel line.
3. Empty fuel tank & carburetor, refill with fresh, clean gasoline.
4. Empty fuel tank & carburetor, refill with fresh, clean gasoline.
5. Contact a qualified service centre/department.
Excessive
vibration
1. Loose parts or damaged
augers or impeller.
1. Tighten all fasteners. Replace damaged parts. If vibration
remains, contact a qualified service centre/department.
Recoil starter
is hard to pull
1. Frozen recoil starter.
1. See “IF RECOIL STARTER HAS FROZEN”
in the Operation section of this manual.
Loss of traction 1. Drive belt is worn.
1. Check / replace drive belt.
2. Check / reinstall drive belt.
drive / slowing
of drive speed
2. Drive belt is off of pulley.
3. Friction drive wheel is worn. 3. Contact a qualified service centre/department.
Loss of snow
discharge or
slowing of
1. Auger belt is off of pulley.
2. Auger belt is worn.
3. Clogged discharge chute.
1. Check / reinstall auger belt.
2. Check / replace auger belt.
3. Clean snow chute.
4. Remove debris or foreign object from augers / impeller.
snow discharge 4. Augers / impeller jammed.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
AUGER HOUSING / IMPELLER ASSEMBLY
5
11
6
11
7
15
16
14
12
8
13
4
11
17
12
3
10
11
1
9
2
33
32
34
30
31
31
26
36
29
28
20
27
21
22
23
25
35
24
23
22
2 (EXPLODED)
21
19
18
01.07.004-B
20
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
AUGER HOUSING / IMPELLER ASSEMBLY
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
5
6
7
8
175321X479
196710
188909
191079
175322
178675X008
192199
405400
73800400
74780426
155377
163183
19111507
10040500
74940516
180355
194189
407760
407761
407766
407770
407762
174697
407763
407764
189282
407758
174683
407757
7836M
IMPELLER
GEARBOX ASSEMBLY
BEARING
IMPELLER PULLEY
DISCHARGE BASE
CORNER BRACKET
CLEAN OUT TOOL
TOOL CLIP
NUT 1/4−20
SCREW 1/4−20 X .625
NUT 5/16−18
SCREW 5/16−18 X .625
WASHER
LOCKWASHER 5/16
SCREW 5/16−18 X 1.00
CARRIAGE BOLT
SCREW 13−16 X .625
PLUG
GEARBOX COVER RH
GASKET
SEAL
BEARING
THRUST WASHER 1.00
WORM GEAR
AUGER SHAFT
SQUARE KEY
BEARING
THRUST WASHER
IMPELLER SHAFT
ROLL PIN
THRUST WASHER
THRUST BEARING
BEARING
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
174681
174684
407769
407768
407767
407765
O−RING
SCREW 5/16−18 X .750
GEARBOX COVER LH
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
AUGER HOUSING / IMPELLER ASSEMBLY
1
KEY
PART
NO.
404928X428
404931X479
72270505
155377
NO.
1
DESCRIPTION
AUGER HOUSING
SCRAPPER BAR
CARRIAGE BOLT 5/16−18 X .625
NUT 5/16−18
2
3
4
3 (5x)
4 (5x)
2
01.07.001-A
1
KEY
NO.
PART
NO.
2
DESCRIPTION
1
2
405985X479
405986X479
AUGER 24 LH
AUGER 24 RH
01.07.008-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
AUGER HOUSING / IMPELLER ASSEMBLY
2
3
1
1
KEY
PART
NO.
NO.
DESCRIPTION
2
1
2
3
174658
411939
179582
AUGER BEARING
BEARING PLUG
SCREW 5/16−18 X 1.00
3
01.07.005-A
3
4
2
KEY
NO.
PART
NO.
DESCRIPTION
4
1
2
3
4
174762X479
178777X479
72270506
751153
SKID PLATE LH
SKID PLATE RH
CARRIAGE BOLT 5/16−18 X .75
NUT 5/16−18
01.11.001-A
1
3
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
CONTROL PANEL / DISCHARGE CHUTE
2
11
10
5
8
3
6
9
11
4
6
11
KEY
NO.
PART
NO.
7
DESCRIPTION
1
1
2
3
4
5
6
404770X428
178633X428
420325
179096X479
189713X428
128415
CHUTE WELDMENT
DEFLECTOR WELDMENT
DEFLECTOR SEAL
STRAP
KNOB BLACK
POP RIVET
7
8
9
185600
72270505
191730
SHOULDER BOLT 1/4−20 X .704
CARRIAGE BOLT 5/16−18 X .625
NUT 1/4−20
10
11
155415
179246
WASHER
PLASTIC WASHER
01.09.001-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
CONTROL PANEL / DISCHARGE CHUTE
2
2
1
*3
*6
*6
KEY
NO.
PART
NO.
DESCRIPTION
1
2
*3
*4
*5
*6
420337
17501010
420678
420677
420675
420674
LEVER/CABLE ROTATOR ASSEMBLY
SCREW 10−24 X .625
ROTATOR HEAD
ROTATOR PIVOT BRACKET
PULLEY PIVOT
*4
01.09.007-A
*5
CABLE ASSEMBLY
NOTES:
1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
HANDLES
10
2
11
7
4
8
9
9
5
7
6
1
3
13
8
12
13
14
14
01.08.002-D
12
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
5
6
7
412683X479
412681X479
412682X479
412679X008
420889X008
412677
CONTROL PANEL
CONTROL LEVER LH
CONTROL LEVER RH
TRACTION ROD ARM
IMPELLER ROD ARM
INTERLOCK ROD
SPACER
412680
8
9
10
11
12
13
14
169675
17060408
414280
414281
178899
19131316
72120618
RETAINER
SCREW 1/4−20 X .50
KNOB BLACK
KNOB RED
HANDLE KNOB
WASHER 3/8
CARRIAGE BOLT 3/8−16 X 2.25
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
HANDLES
5
1
KEY
NO.
PART
NO.
6
DESCRIPTION
8
7
1
2
3
4
5
6
7
8
9
419800X479
419801X479
196944
196943
199513
74780512
74780524
751153
PLOW HANDLE LH
PLOW HANDLE RH
PANEL BRACKET LH
PANEL BRACKET RH
HANDLE GRIP
SCREW 5/16−18 X .750
SCREW 5/16−18 X 1.50
NUT 5/16−18
2
9
5
3
8
6
7
8
9
4
155415
WASHER
01.08.003-A
1
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
419797X479
405784X479
150078
LOWER HANDLE
2
PIVOT SUPPORT WELDMENT
SCREW 5/16−18 X .750
SCREW 3/8−16 X 1.00
4
17000616
3
4
4
4
3
01.05.002-B
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
HANDLES
2
KEY
NO.
PART
NO.
DESCRIPTION
1
1
2
3
4
5
6
7
8
9
10
180480
405740
180445
187716
180447
178669
180926
72270506
155377
169675
IMPELLER ROD ASSEMBLY
TRACTION ROD ASSEMBLY
SHIFTER ROD TOP
SHIFTER ROD BOTTOM
SPRING SLEEVE
IMPELLER SPRING
TRACTION SPRING
CARRIAGE BOLT 5/16−18 X .75
NUT 5/16−18
3
8
9
RETAINER
4
5
7
10
5
6
01.12.001-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
HANDLES
3
1
2
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
183352
184471
175262
CONSOLE PANEL
SCREW 10−24 X .625
SCREW 10−24 X 1.25
3
2
01.10.001-B
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
DRIVE
ITEM 43 EXPLODED
69
2
68
16
1
71
17
74
18
70
15
14
15
72
9
12
11
20
21
22
73
11
76
13
24
9
19
9
23
10
11
76
4
34
75
8
76
7
6
24
5
33
23
31
76
3
35
33
39
30
29
32
35
50
28
49
51
26
52
53
36
47
27
24
76
54
55
56
49
51
57
58
26
37
45
46
52
4
23
38
49
48
67
43
62
76
44
40
25
61
63
24
64
42
59
65
41
4
40
60
01.02.006-E
66
30
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
DRIVE
KEY
NO.
PART
NO.
KEY
NO.
PART
NO.
DESCRIPTION
DESCRIPTION
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
12000007
184471
410877
413429X479
420900
414557
180522
74780520
187786
73930500
59289
175331
10040500
74610516
409475
180478
400026
850263
11050500
155452
419925X007
175324X479
180523
74780524
166785
175330
178828
85179
851084
402504
401820
198791
402393
17541008
402511
402394
132010
150078
E−RING .375
SHOULDER SCREW
BOTTOM PAN
SPRING BRACKET
DRIVE PLATE ASSEMBLY
IDLER SPRING
IDLER PULLEY
SCREW 5/16−18 X 1.25
IDLER ARM
1
2
3
4
5
6
7
8
198474
SPEED SELECTOR ASSEMBLY
SCREW 10−24 X .625
END PLATE
SCREW 5/16−18 X .50
WASHER
CONTROL ARM
CLEVIS PIN
SHIFTER PLATE
SHOULDER BOLT
SHIFTER BRACKET
NUT 1/4−20
CLUTCH PLATE
CLUTCH BRACKET
SHIFTER LINK
RETAINER
CONTROL SHAFT
CLUTCH ROD
RETAINER
SHIFTER YOKE
PIVOT ROD
RETAINER
RETURN SPRING
NUT 5/16−18
BEARING
NUT 5/16−18
RUBBER WHEEL PLATE
RUBBER RING
BEARING
17501010
402685X428
17490508
57079
405485
198580
403097X004
402881
403096X004
191730
402856X004
416717X004
187101
700279
406109
402568
169675
401732
402310
402882
402878
751153
408981
73930500
198176X479
179831
175344
178613
74760514
12000012
402187
401619
417234
17490408
401984
180135
9
NUT 5/16−18
WASHER
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
PIVOT BUSHING
LOCKWASHER 5/16
SCREW 5/16−18 X 1.00
SPACER
TRACTION PULLEY
WASHER 3/8
LOCKWASHER 3/8
LOCKWASHER
BELT GUIDE
IDLER ARM
IDLER BRACKET
IDLER PULLEY
SCREW 5/16−18 X 1.50
NUT 5/16−18
PIN IDLER PIVOT
IDLER SPRING
RETAINER
SCREW 3/8−24 X 1.375
PULLEY SHAFT
DRIVE PLATE
BEARING
PULLEY HALF
SCREW 10−24 X .50
SPACER BEARING
SWING PLATE
WHEEL HUB
SCREW 5/16−18−.875
RETAINER RING
SPROCKET SHAFT
CHAIN
SPROCKET WELDMENT
SCREW 1/4−20 X .50
SHIFTER BRACKET
SPRING
NUT 3/8−16
SCREW 5/16−18 X .750
402652
PLATE PIVOT ROD
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
DRIVE
6
7
1b
4
8
3
1b
1a
7
2
3
5
4
01.03.005-A
6
KEY
PART
NO.
NO.
DESCRIPTION
1
188226
179352
9465M1
402691
174697
179830
146315
17490508
155443
189282
(assy of 1a,1b) AXLE ASSEMBLY
AXLE SHAFT
ROLL PIN 3/16
SPROCKET
THRUST WASHER
BEARING
SCREW 5/16−18 X .625
BOLT 5/16−18 X .500
CLIK PIN
1a
1b
2
3
4
5
6
7
8
SQUARE KEY
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
CHASSIS / ENGINE / PULLEYS
4
2
3
4
3
KEY
NO.
PART
NO.
DESCRIPTION
- -
- - - - - -
TECUMSEH ENGINE MODEL
LH195SP-67504D
FRAME
ENGINE MOUNT PLATE
BOLT 3/8−16
1
2
3
4
409346X428
417014X428
150406
1
150078
SCREW 5/16−18 X .750
01.00.009-A
1
KEY
NO.
PART
NO.
DESCRIPTION
1
2
3
4
192213
179157
419744
408007
BELT COVER
IMPELLER PULLEY
TRACTION BELT
IMPELLER BELT
2
3
01.04.019-A
4
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
WHEELS / BAG OF PARTS
KEY
NO.
PART
NO.
DESCRIPTION
1
2
187831X421
187866X421
WHEEL ASSEMBLY LH
WHEEL ASSEMBLY RH
1
2
01.06.001-A
2
KEY
NO.
PART
NO.
4
DESCRIPTION
3
1
2
3
4
5
6
7
169675
180684
73800600
19131316
198636
198638
73800400
RETAINER PIN
WRENCH
LOCKNUT 3/8−16
WASHER 3/8
SHEAR BOLT 1/4−20 X 1−3/4
SPACER
LOCKNUT 1/4−20
1
7
6
01.14.006-A
5
1
KEY
NO.
PART
NO.
DESCRIPTION
1
35062
SAFETY IGNITION KEY
01.14.008-A
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
SNOW THROWER - MODEL PR524 (96192001502)
DECALS
1
2
4
9
8
6
7
5
3
1
KEY PART
NO. NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
181037
187868
181035
181042
187893
181033
415391
415390
415475
DECAL, DANGER
DECAL, POULAN PRO, HP/24"
DECAL, DANGER, DEFLECTOR
DECAL, DANGER
DECAL, POULAN PRO
DECAL, INSTRUCTION
DECAL, TRACTION LEVER
DECAL, AUGER LEVER
DECAL, SPEED CONTROL
OWNER’S MANUAL, ENGLISH
OWNER'S MANUAL, FRENCH
- - 421104
- - 421105
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.
Failure to do so could be hazardous, damage your snow thrower and void your warranty.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects
in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer pur-
chaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part
which we find to be defective due to materials or workmanship. This Warranty is subject to the following limitations
and exclusions.
1. This warranty does not apply to the engine or components parts thereof. Please refer to the applicable manu-
facturer's warranty on these items.
2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the
purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by
the purchaser unless such return is requested by the manufacturer.
3. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date
of original purchase.
4. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained
in accordance with the instructions furnished. This Warranty does not apply to any product which has been sub-
jected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the
product.
5. Exclusions: Excluded from this Warranty are belts, shear pins, normal wear, normal adjustments, standard hard-
ware and normal maintenance.
6. In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.
Should you have any unanswered questions concerning this Warranty, please contact:
In Canada contact:
Poulan Pro
Poulan Pro, Customer Service Department
Customer Service Department
5855 Terry Fox Way
1030 Stevens Creek Road
Mississauga, Ontario
Augusta, GA 30907 USA
L5V 3E4
giving the complete mfg. ID#, serial number and date of purchase of your product and the name and address of the
authorized dealer from whom it was purchased.
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED
WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WAR-
RANTIES. Some areas do not allow the limitation of consequential damages or limitations of how long an implied
Warranty may last, so the above limitations or exclusions may not apply to you. This Warranty gives you specific
legal rights, and you may have other rights which vary from locale to locale.
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.
Download from Www.Somanuals.com. All Manuals Search And Download.
|