PT1503Z Manual
1-866-PLANAR-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
PREFACE
About this manual
This manual is designed to assist you in setting up and using your New Planar LCD Monitor. Information in this
document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the con-
tents. The information in this document is subject to change without notice. This document contains proprietary
information protected by copyright. All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic or other means, in any form, without prior written permission of the manufacturer.
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Opeartion is subject to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful inerference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
•
•
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Caution:
To comply with the limits for an FCC Class B computing device, always use the shielded signal cord supplied
with this unit.
The Federal Communications Commission warns that changes or modifications of the unit not expressly ap-
proved by the party responsible for compliance could void the user’s authority to operate the equipment.
CE mark for Class B ITE (Following European standard EN55022/1998;
EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998)
Radio Frequency Interference Statement
Warning:
This is a Class B product. In a domestic environment, this product may cause radio interference in which case the
user may be required to take adequate measures.
Canadian Doc Notice
For Class B Computing Devices
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Planar User’s Manual
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set
out in the Radio Interference Regulation of the Canadian Department of Communications.
“Le présent appareil numérique n’èmet pas de bruits radioélectriques dépassant les limites applicables aux appa-
reils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère
des Communications du Canada”
Important Safety Instructions
Please read the following instructions carefully. This manual should be retained for future use.
1. To clean your New Planar LCD Monitor screen, first, make sure the Monitor is in the power off mode. Un-
plug the Monitor from its power source before cleaning it. Do not spray liquid cleaners directly onto the unit.
Stand away from your New Planar LCD Monitor and spray cleaning solution onto a rag. Without applying
excessive pressure, clean the screen with the slightly dampened rag.
2. Do not place your New Planar LCD Monitor near a window. Exposing the Monitor to rain, water, moisture
or sunlight can severely damage it.
3. Do not place anything on top of the Monitor-to-PC signal cord. Make sure the cord is placed in an area
where it will not be stepped on.
4. Do not apply pressure to the LCD screen. Excessive pressure may cause permanent damage to the display.
5. Do not remove the cover or attempt to service this unit by yourself. You may void the warranty. Servicing
of any nature should be performed only by an authorized technician.
6. Safe storage of your New Planar LCD Monitor is in a range of minus 20 to plus 65 degrees Celsius (68°F-
149°F). Storing your New Planar LCD Monitor outside this range could result in permanent damage.
7. If any of the following occurs, immediately unplug your Monitor and call an authorized technician.
•
•
•
The power or Monitor-to-PC signal cord is frayed or damaged.
Liquid has been spilled onto the Monitor, or it has been exposed to rain.
The Monitor has been dropped or the case has been damaged.
8. The appliance should be disconnected from the mains by pulling the mains power cord/mains plug.
9. The socket-outlet shall be installed near the equipment and shall be easily accessible.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
TABLE OF CONTENTS
PREFACE........................................................................................................................................................................ I
TABLE OF CONTENTS.............................................................................................................................................III
CHAPTER 1 ....................................................................................................................................................................1
Your New Planar LCD Monitor!............................................................................................................. 1
Unpacking ............................................................................................................................................... 1
Identifying Components ........................................................................................................................ 1
Your New Planar LCD Monitor — Front View ..................................................................................................2
Your New Planar LCD Monitor — Rear View....................................................................................................2
Adjusting the Viewing Angle................................................................................................................. 3
Connecting AC Power............................................................................................................................ 3
Connecting Video................................................................................................................................... 4
Connecting the Stereo Speakers (optional) ........................................................................................ 4
CHAPTER 2 ....................................................................................................................................................................7
Your New Planar LCD Monitor’s Display Controls ............................................................................. 7
Adjusting the Monitor’s Display ........................................................................................................... 7
OSD Main Menu .................................................................................................................................................7
OSD Main Menu ...................................................................................................................................... 7
APPENDIX A ................................................................................................................................................................11
Planar TFT LCD Monitor Specifications............................................................................................. 11
APPENDIX B ................................................................................................................................................................12
Timing for Model PT1503Z (XGA Resolution).................................................................................... 12
APPENDIX C ................................................................................................................................................................13
Troubleshooting Procedures .............................................................................................................. 13
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 1
Your New Planar LCD Monitor
Your New Planar LCD Monitor!
Your New Planar LCD Monitor has been designed to be versatile, ergonomic and user-friendly. Your New Planar
LCD Monitor is capable of displaying most standards, from 640 x 480 VGA to 1024 x 768 XGA. The digital controls
located on the front panel allow the user to easily adjust the Monitor’s display parameters. Your New Planar LCD
Monitor’s small footprint allows you more room in your workspace for other peripherals. Lightweight and compact,
your New Planar LCD Monitor is the perfect solution for users on the go. You can use your New Planar LCD Monitor
for everything from making business presentations to playing computer games. The two stereo speakers allow you to
further expand your computer’s multimedia capabilities by connecting your computer’s Audio out port to your New
Planar LCD Monitor’s Audio in port. If you have a complete full workstation, your New Planar LCD Monitor has the
additional feature of an optional wall-mountable stand for added convenience.
The architecture of your New Planar LCD Monitor incorporates an LCD panel that produces a clear display with low
radiation emission, limiting health concerns. With its low power consumption, your New Planar LCD Monitor helps
you reduce your power bill.
Unpacking
Before you unpack your New Planar LCD Monitor, prepare a suitable workspace for your New Planar LCD Monitor
and computer. You need a stable, level and clean surface near a wall outlet. Even though your New Planar LCD
Monitor uses very little power, you should put it in a location that allows sufficient airflow to ensure that your New
Planar LCD Monitor and your computer do not become too hot. Set up your New Planar LCD Monitor so that the
panel does not face a window where sunlight often comes in. The glare caused by sunlight reflecting off your New
Planar LCD Monitor’s screen will make it difficult to see.
Using a computer for an extended period of time with a poor workstation set-up and incorrect working
habits can cause health problems. The science of ergonomics studies the relationship between health
and a suitable working environment. There is a section on ergonomics at the end of this chapter. For
more information on ergonomics, contact your nearest computer bookstore, or local library. The Internet
also has information on this and other subjects.
After you unpack your New Planar LCD Monitor; make sure the following items are included in the box and in good
condition:
•
LCD Monitor
•
•
•
•
•
Monitor-to-PC signal cable
1.5M Stereo Jack Audio Cable
AC Adapter
Power cord
This Planar User’s Manual
If you find that any of these items are missing or appear damaged, contact your dealer immediately. Do not throw
away the packing material or shipping carton in case you need to ship or store your New Planar LCD Monitor in the
future.
Identifying Components
Your New Planar LCD Monitor has been designed to provide easy access to all controls and peripheral ports. The
following figures will help you identify your New Planar LCD Monitor’s controls and ports.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Planar User’s Manual
Your New Planar LCD Monitor — Front View
1. LCD Screen
This is the LCD monitor screen. It is a 15-inch diagonal, Acitve Matrix Liquid Crystal Display (AMLCD).
The screen is capable of supporting a maximum resolution of 1024 x 768 (XGA).
2. ▲▼ Function Select Buttons
These two buttons allow you to select the control functions in the OSD. Press either button to vertically scroll
through the main menu and submenu items.
3.
Adjust Control Buttons
This button allows you to apply settings and enter submenus in the OSD. This button also serves as an Ad-
justment Control button.
4. Power ON / OFF
5. Power-On Indicator
This LED indicator stays lit when the power is on and when the monitor is receiving a proper video signal.
The LED will blink slowly when the LCD monitor is in power saving mode.
6. Monitor Stand
The monitor stand supports the LCD monitor.
7. Stereo Speakers
8. VGA input cable
Your New Planar LCD Monitor — Rear View
1. LCD Monitor’s VGA Connector
This 1.5 meter cable has two 15-pin D-Sub VGA connectors used to connect the monitor to your PC’s VGA
card.
2. AC Power Jack
Connect the AC adapter cable to this jack.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
3. Audio Line In (optional)
Connect your PC’s Line out to this jack to listen to the PC’s audio through your New Planar LCD Monitor’s
stereo speakers. (You can also connect your CD-ROM’s Line out to this jack.)
4. PS/2 Connector for Optional Touch Screen
Connect this PS/2 connector to your PC’s RS232 9-pin serial port connector to use the Optional Touch
Screen. A PS/2 to RS232 cable is provided with the Optional Touch Screen package. To install the Optional
Touch Screen driver, please contact your local distributor.
Adjusting the Viewing Angle
Your LCD Monitor is designed to allow you to adjust it to a comfortable viewing angle. The LCD Monitor’s angle
setting range is from -5° to 25°.
Connecting AC Power
1. Plug the female end of the power cable into the AC-adapter. Plug the male end of the power cord into a wall
socket. The plug on the power cable will vary according to the electrical standard in your area.
2. Connect the power connector of the adapter into the jack of the LCD Monitor. The AC power jack is located
at the rear of the Monitor near the D-sub VGA connector.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Planar User’s Manual
Connecting Video
1. Turn off your PC and the LCD Monitor before connecting your LCD Monitor to the computer.
2. Connect the VGA signal cable to the D-sub VGA connector located at the rear of the monitor.
3. Connect the other end of the signal cable to the PC’s VGA port.
4. Make sure the signal cable heads are securely connected to the VGA ports of your PC and Monitor. Tighten
the connecting screws to ensure a secure connection.
5. Turn on your computer and LCD Monitor.
Connecting the Stereo Speakers (optional)
Please refer to the following instructions for connecting the LCD Monitor’s stereo speakers.
1. Connect the 1.5M sound cable to the Lineout of your PC’s audio card.
2. Connect the other end of the 1.5M sound cable to the LCD Monitor’s line-in jack.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
3. You can adjust the sound volume of the stereo speakers by using the speaker volume control function on the
OSD (On-Screen Display).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Planar User’s Manual
Connecting the Optional Touch Screen (optional)
Your LCD Monitor has an optional touch screen feature. If your LCD monitor has this feature, connect the LCD
Monitor’s PS/2 connector to your PC’s 9-pin RS232 serial port to enable the touch screen.
1. Connect the PS/2 connector to the RS232 cable provided with the optional touch screen
package to the PS/2 Mini-Din port at the back of the LCD Monitor.
2. Connect the 9-pin RS232 connector end of the PS/2 to RS232 cable provided with the op-
tional touch screen package to the 9-pin RS232 serial port at the back of your PC.
Power Management System
The LCD Monitor complies with the VESA DPMS (version 1.0p) power management proposal. The VESA DPMS
proposal provides four phases of power saving modes by detecting the horizontal or vertical sync signal.
When the LCD Monitor is in power saving mode or detects an incorrect timing, the Monitor screen will go blank and
the power LED indicator will start to blink.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CHAPTER 2
The Display Controls
Your New Planar LCD Monitor’s Display Controls
This chapter covers your New Planar LCD Monitor’s On Screen Display (OSD). Using the OSD, you can adjust the
contrast, brightness, display position, display clarity, and color temperature. You can also adjust the stereo speaker
volume and set OSD parameters. Please read this chapter carefully to get the most out of your New Planar LCD Moni-
tor.
Adjusting the Monitor’s Display
The LCD monitor features an intuitive, menu-driven, On-Screen Display (OSD). You can access the OSD any time
that the PC is powered up. If the PC is in a power saving mode, or is powered down, the OSD is inaccessible.
OSD Main Menu
To activate the OSD Main Menu, press the topmost▲ Function key. To navigate the topline menu,
use the down arrow key ▼ to scroll between the main menu choices.
The option that is currently selected is highlighted in yellow. Each main menu has an associated
submenu and is further described.
OSD Main Menu
To access the OSD Main Menu, simply press the Function button. The following screen will appear.
Main menu
Submenu
Description
Figure 2-1: The OSD Main Menu
The 7-topline menus are:
The Auto Adjust option lets the monitor determine and select the settings that are most appropriate
for your system requirements. This function will tune the display to your computers video card.
The Monitor-Control option allows you to adjust the LCD monitor’s display characteristics such
as the display’s horizontal or vertical position, display phase, display clock, and factory reset.
Adjusting these settings should only be necessary if the results from Auto-Adjust function are not
satisfactory.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Planar User’s Manual
The OSD-Control option allows you to adjust the position and setting of the monitor’s On Screen
Display.
The MISC-Control option allows you to select the desired text language of the OSD, adjust the
monitor speaker volume, and to display the current video information being sent to the monitor
from your video card.
The Graphic-Control option allows you to adjust the display contrast, brightness, sharpness, and
color settings.
The Graph/Tex option allows you to switch DOS text resolution from 640x400 and 720x400. This
function has no effect within graphic operating systems such as MS Windows™.
The OSD Exit option closes the On Screen Display.
Auto Adjust Procedure
The Auto Adjust procedure is activated by pressing the Adjust key while the Auto Adjust topline menu is selected. The Auto
Adjust procedure takes approximately 2 seconds to complete. Once finished, the OSD menu will disappear after a short time-out
period.
The Monitor- Control Option
Pressing the Adjust key on the monitor activates the Monitor-Control submenu. Use the ▲FUNCTION ▼ select buttons to
scroll between the submenu items. You should only use this menu item if the results of the Auto Adjust function are not satisfac-
tory.
H-Position: Press the Adjust buttons to horizontally move the display image to the desired position.
V-Position: Press the Adjust buttons to vertically move the display image to the desired position.
Phase: Press the Adjust buttons to fine-tune the displayed image. An improper phase adjustment will
result in pixel jitter or display noise.
Clock: Press the Adjust buttons to stabilize the display clock timing. An improper clock setting will
result in wide vertical bands on the display.
Reset: Press the Adjust button to reset the Monitor-Control submenu values to the factory default val-
ues.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Exit: Press the Adjust button key to exit the Monitor-Control submenu.
OSD - Control Option
Pressing the Adjust button on the monitor activates the OSD-Control submenu. Use the ▲ FUNCTION ▼ select
buttons to scroll between the submenu items.
OSD-H-Position: Press the Adjust buttons to horizontally move the OSD menu.
OSD-V-Position: Press the Adjust buttons to vertically move the OSD menu.
Exit: Press the Adjust button key to exit the OSD-Control submenu.
Misc. - Control Option
Pressing the the Adjust button on the monitor activates the Misc-Control submenu. Use the ▲ FUNCTION ▼ select buttons
to scroll between the submenu items.
Language: Press the Adjust buttons to select the desired OSD display language. Languages supported: Eng-
lish, German, French, Spanish, and Italian.
Audio Volume: Press the Adjust buttons to increase or decrease the volume of the monitor speakers.
Information: The Information submenu displays the current resolution, vertical refresh rate, and monitor firmware
version.
Exit: Press the Adjust button to exit the Misc-Control submenu.
Graphic Control Option
Pressing the Adjust button on the monitor activates the Graphic-Control submenu. Use the ▲ FUNCTION ▼ select buttons
to scroll between the submenu items.
Contrast: Press the Adjust buttons to adjust the difference between the lightest and darkest areas on the dis-
play. The contrast level can range from 0 to 63.
Brightness: Press the Adjust buttons to adjust the intensity of the monitor backlight.
Sharpness: Press the Adjust buttons to select the desired sharpness setting.
Color: Press the Adjust buttons to select the desired color temperature setting. The available options are CIE
coordinate values 9300°, 6500°. Selecting the USER option, allows for customization of the Red, Green and Blue
color coordinates.
R, G and B: Press the Adjust buttons to make individual adjustments to the Red, Green, and Blue coordinates
for the customized color temperature. There are 127 levels of adjustments (0 - 127) available.
Before adjusting these fields, you must select the User option in the Color submenu.
Exit: Press the Adjust button to exit the Graphic-Control submenu.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Planar User’s Manual
Graph/Text Option
Pressing the Adjust button on the monitor toggles the DOS resolution between 640x400 and 720x400.
OSD Exit
Pressing the Adjust button on the monitor will exit the OSD menu. The OSD menu will also exit after a brief, timout period.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A
Technical Information
Planar TFT LCD Monitor Specifications
Model
Planar PT1503Z
LCD Panel
15"XGA
Control Functions Power
Software Power switch with LED indicator
(Press to turn off, over 1 sec. to turn on)
Main Menu
Submenu
On-Screen Display (OSD)
Auto Adjust
Monitor Control
OSD Control
Misc. Control
Graphic Control
Graph/Text
Horizontal Position/Vertical Position/Phase/Clock/Reset/Exit
OSD Horizontal Position/OSD Vertical Position/Exit
Language/Audio Volume/Information/Exit
Contrast/Brightness/Sharpness/Color/R/G/B/Exit
640 x 400/720 x 400
OSD Exit
Display Area (mm)
304.1 x 228.1 (15" diagonal)
40 ms typical
Response Time (ms)
(Rise+Fall)
Contrast Ratio
Brightness
350:1 typical
250 cd/m2 typical
Viewing Angle
Pixel Pitch (mm)
Display Colors
Video Interface
Horizontal: 60°/60° (L/R), Vertical: 45°/60° (U/D)
0.297 x 0.297
Dithering 16M
VGA Compatible Analog RGB/ Composite Sync.
Scanning Frequency
H/V, Hz
24-62K
50-75
Number of Factory Preset
Mode
22
Power Management
Meets VESA DPMS
40/4.5Max.
Power Consumption
(ON/OFF, W)
Dimensions WxHxD mm
Net Weight (Kg)
408x388x175
6.9
Power Supply
12V/3.75A, 45W
Universal Input AC Adapter (External)
Options
Other Stands (Wall-mount), Touch Screen, S-Video/Video cable
Operating Temperature: 0 to 40° C
Environment
Relative Humidity: 10% to 90%
Audio (Two 1 Watt
Yes
speakers with amplifier)
Regulatory
UL, CSA, TÜV/GS, CE Mark, VCCI, T-Mark, FCC B DoC, TCO ’99 (optional), Nordic
11
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B
Supported Timing
Timing for Model PT1503Z (XGA Resolution)
Vertical
Scanning
Frequency
(Hz)
Horizontal
Scanning
Frequency
(kHz)
Item
Standards
Resolution
Dot Clock
(MHz)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
NEC PC98
NEC PC98
MAC 13" mode
MAC 16" mode
MAC 17" mode
VGA
640x400
640x400
640x480
832x624
1024x768
640x350
640x400
640x480
640x480
640x480
800x600
800x600
800x600
800x600
720x400
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
1024x768
25.20
21.05
30.24
57.28
80.00
25.18
25.18
25.18
31.50
31.50
36.00
40.00
50.00
49.50
28.32
65.00
75.00
78.75
71.64
64.13
74.25
84.38
70.15
56.42
66.67
74.55
75.02
70.09
70.09
59.94
72.81
75.00
56.25
60.32
72.19
75.00
70.09
60.00
70.07
75.03
66.13
59.98
70.04
77.07
31.50
24.83
35.00
49.73
60.24
31.47
31.47
31.47
37.86
37.50
35.16
37.88
48.08
46.88
31.47
48.36
56.48
60.02
53.96
48.29
56.59
62.04
VGA
VGA
VESA
VESA
VESA
SVGA
VESA
VESA
VGA
XGA
VESA
VESA
SUN
SUN
SUN
*Once a mode is optimized, there is no need to make any further adjustment
as long as the VGA card remains unchanged.
*Specifications are subject to change without notice.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX C
Troubleshooting
Troubleshooting Procedures
This LCD Monitor was pre-adjusted in the factory with standard VGA timing. Due to output timing differences among
various VGA cards, you may initially experience an unstable or unclear display when a new display mode or new
VGA card is selected.
This LCD Monitor Supports Multiple VGA Modes. Refer to Appendix B for a listing of the factory-preset
modes supported by this LCD Monitor.
PROBLEM: Display is Unclear and Unstable
1. To stabilize and clarify your display, follow this procedure in this order:
2. It’s best to adjust the display on a screen displaying of vertical lines. In Windows, load a wallpaper bitmap
that has vertical lines in it. (or you can select the window shut down screen)
3. After you have the wallpaper loaded, open the OSD and select the “Clock” function. Press the top (or bottom)
Adjustment Control button and continue pressing the button until you see vertical dark and light lines across
the screen.
4. When you can see distinct light and dark vertical bands, stop pressing the Adjustment Control button. Now
press the opposite (top or bottom) Adjustment Control button. The vertical dark and light bands will decrease
in number. Keep pressing the button until the distinct bands disappear and you have a clear display.
5. Next, press the Function Control button to choose the “Phase” function. The Phase will adjust the horizontal
display. Press the top (or bottom) Adjustment Control button and you will see horizontal dark and light lines
appear. The number of lines increases as you press the button. Now press the bottom (or top) Adjustment
Control button until the lines disappear and you have a clear display.
PROBLEM: There is no LCD Display
If there is no display on the LCD, please perform the following steps:
1. Make sure that the power indicator on your New Planar LCD Monitor is lit, all connections are secure, and the
system is running on the correct timing. Refer to the Appendix B for information on timing.
2. Turn off your New Planar LCD Monitor and then turn it back on again. Press the upper Function Control but-
ton (refer to Chapter 2) once and then press either the upper or lower Adjustment Control button several
times. If there is still no display, press the other Adjustment Control button several times.
3. If step 2 doesn’t work, connect your PC system to another external CRT. If your PC System functions prop-
erly with a CRT Monitor but it does not function with your New Planar LCD Monitor, and your New Planar
LCD Monitor’s power LED is blinking, the output timing of the PC’s VGA card may be out of the LCD’s
synchronous range. Please change to an alternate mode listed in Appendix B or replace the VGA card and re-
peat steps 1 and 2.
4. If the PC doesn’t function with the CRT monitor neither, check BIOS to see if there is a dual scan setting un-
der the display mode item. Set the BIOS display mode to Dual Scan or CRT and try again. If there is still no
display, then there may be a problem with your system. Contact technical support.
5. If the power LED is not lit, check to see if the AC power connector is securely connected. Verify that the AC
adapter LED is lit. If the AC adapter LED is not lit, please contact your Planar dealer for assistance.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
|