®
PMC9A
High-Resolution Color
Monitor
Installation/
Operation Manual
C1909M (4/01)
In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150
International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be observed.
1. Operate this unit only from the type of power source indicated on the label.
2. Do not block or cover ventilation openings on the back or bottom of the monitor
cabinet.
3. Do not place this monitor near a radiator or heating vent.
4. Do not push objects of any kind through cabinet openings. This may result in fire or
electrical shock.
5. Before adding attachments always ask a service technician to perform routine safety
tests to determine that equipment is in safe operating condition. Ground potential tests
should be part of the routine safety check made by the service technician.
6. Do not place monitor on an unstable cart, stand, or shelf where it may fall and injure
personnel or damage equipment.
7. Route power cords so that they cannot be walked upon or tripped over. Do not allow
anything to rest on the power cord.
8. Do not install monitor in wet areas, or where it may be exposed to rain or water. Do not
spill liquid of any kind on the unit.
9. Unplug the power cord from the unit before cleaning the display. Use only a damp
cloth. Do not use alcohol, spirits, or ammonia to clean the display. DO NOT AT-
TEMPT TO CLEAN THE INTERIOR OF THIS UNIT-THIS ACTION MUST
BE PERFORMED BY THE SERVICE TECHNICIAN AS REQUIRED DUR-
ING NORMAL MAINTENANCE.
10. Refer all servicing to qualified service personnel. REMOVAL OF BACK COVER
BY UNAUTHORIZED PERSONNEL MAY EXPOSE THE USER TO DAN-
GEROUS VOLTAGES OR OTHER HAZARDS.
11. Unplug the unit immediately and notify the service technician.
A. If liquid has been spilled into the display or the display has been exposed to rain
or water.
B. If the unit has been dropped or the cabinet damaged.
C. If fuses continue to blow.
D. If the power cord is damaged or frayed.
E. If a distinct change from normal operation is apparent.
12. A CCC-approved power cord must be used to power this equipment when used in
China.
When replacement parts are required, be sure that the service technician uses components
specified by the manufacturer which have the same characteristics as the original parts.
UNAUTHORIZED SUBSTITUTIONS MAY RESULT IN FIRE, ELECTRICAL
SHOCK OR OTHER HAZARDS.
Upon completion of any service or repairs, ask the technician to perform safety checks to
determine that the equipment is in safe operating condition.
WARNING: SERIOUS SHOCK HAZARDS EXIST WITHIN THE COVERS
OF THIS MONITOR. DO NOT OPEN THE COVERS UNDER ANY CIRCUM-
STANCES, THERE ARE NO USER SERVICEABLE COMPONENTS INSIDE.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous volt-
age constituting a risk of electric shock is
present within this unit.
C A U T I O N :
RISK OF ELECTRIC SHOCK.
This symbol indicates that there are impor-
tant operating and maintenance instructions
in the literature accompanying this unit.
DO NOT OPEN.
Please thoroughly familiarize yourself with the information in this manual prior to installation
and operation.
Pelco Manual C1909M (4/01)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION
The PMC9A is a high-resolution, 9-inch (23 cm) color monitor. The unit has a resolution of
300 TV lines producing an excellent-quality picture. The monitor’s power input of 100-240
VAC, 50/60 Hz, is automatically detected upon power up. All image adjustment controls are
conveniently located on the front panel of the monitor.
INSTALLATION
The monitor may be placed on any flat surface (desk or
table) or rack-mounted. To rack-mount the monitor follow the
instructions supplied with the rack-mount kit.
1. Video Cable Connection (refer to Table A).
IN
a. Connect the video cable to the BNC video input
labeled VIDEO A IN on the back panel of the
monitor. If the installation requires a second video
input, connect a video cable to the BNC video
input labeled VIDEO B IN.
VIDEO A
OUT
IN
VIDEO B
OUT
NOTE: If using S-Video
connect the video cable to
the input labeled S-VHS IN.
b. Looping Operation Only – Connect a video cable
to the BNC connector labeled VIDEO A OUT. If the
installation requires a second video output,
S-VHS IN
connect a video cable to the BNC video output
labeled VIDEO B OUT. Refer to Figures 2 and 3.
IN
OUT
2. Plug the power cord (provided) into the AC INLET con-
nection on the back panel. Plug the other end of the
cord into a power receptacle.
AUDIO AUDIO
2
1
00595
Figure 1. Back Panel Layout
4
Pelco Manual C1909M (4/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table A. Video Coaxial Cable Requirements
Cable Type*
RG59/U
RG6/U
Maximum Distance
750 ft (229 m)
1,000 ft (305 m)
1,500 ft (457 m)
RG11/U
*Minimum cable requirements:
75 ohms impedance
All-copper center conductor
All-copper braided shield with 95%braid coverage
IN
VIDEO A
OUT
CAMERA
VCR
IN
VIDEO B
CAMERA
OUT
VCR
S-VHS IN
IN
OUT
AUDIO AUDIO
2
1
00598
Figure 2. Looping Operation – One Monitor with External Video Equipment
IN
IN
IN
VIDEO A
VIDEO A
VIDEO A
OUT
OUT
OUT
CAMERA
IN
IN
IN
VCR
VIDEO
OUT
B
VIDEO
OUT
B
VIDEO
OUT
B
S-VHS IN
S-VHS IN
S-VHS IN
IN
IN
IN
OUT
OUT
OUT
AUDIO
2
AUDIO AUDIO
AUDIO AUDIO
AUDIO
1
2
1
2
1
00597
Figure 3. Looping Operation – Maximum of Three Monitors with
External Video Equipment
Pelco Manual C1909M (4/01)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
1. Turn the monitor ON. Wait 30 seconds for the picture tube to warm up and the power
LED indicator to light.
2. Select the video source (V1, V2, S-VHS) using the VIDEO selection button located on
the front panel of the monitor.
3. If required adjust the picture using the control knobs on the front panel.
FRONT PANEL ADJUSTMENTS
SHARP
TINT
Adjust the control to obtain the clearest picture.
Turn the control clockwise to increase the greenish tones in the picture.
Turn the control counterclockwise to increase the reddish tones in the pic-
ture.
COLOR
Turn the control clockwise to increase the saturation level and counterclock-
wise to decrease the saturation level.
BRIGHT
Turn the control clockwise to increase brightness and counterclockwise to
decrease brightness.
CONTRAST Proper adjustment will allow maximum gradations between the darkest and
lightest picture contrast. Turn the control clockwise to increase picture con-
trast and counterclockwise to decrease contrast.
VOLUME
Turn the control clockwise to increase volume and counterclockwise to de-
crease volume.
V1 V2 S-VHS
VIDEO
SHARP
TINT
COLOR BRIGHT CONTRAST VOLUME
POWER
00596
Figure 4. Front Panel Controls
MAINTENANCE
If the quality of the picture is poor and cannot be improved by making adjustments on the
front control panel, inspect all system connections and cable runs.
To reduce the risk of electrical shock, do not remove the cover or the back. No user-
serviceable parts are inside. Refer servicing to qualified personnel, or contact the Pelco
Customer Service Department for assistance. Refer to the Warranty and Return Information
section.
6
Pelco Manual C1909M (4/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
ELECTRICAL
Input Voltage:
100-240 VAC, 50/60 Hz, automatic switching
45 watts
Power Consumption:
Horizontal Resolution: 300 TV lines
Visual Picture Size:
Sweep Linearity:
Speaker Output:
GENERAL
9-inch (23 cm) diagonal
10%
1.0 watt (-3 dBV)
Input/Output
Video:
2 BNC inputs, 75 ohms or Hi-Z
2 looping outputs
Audio:
2 RCA input, Hi-Z
2 looping output
S-Video:
Construction:
Finish:
1 DIN input
Steel cabinet
Black
Dimensions:
8.66 (W) x 8.76 (H) x 12.48 (D) inches
(22 x 22.3 x 31.7 cm)
Weight:
15.4 lb (7 kg)
ENVIRONMENTAL
Operating Temperature: 32° to 106°F (0° to 41°C)
Humidity: 0% to 90% (non-condensing)
(Design and product specifications subject to change without notice.)
This equipment contains electrical or electronic components that must be
recycled properly to comply with Directive 2002/96/EC of the European
Union regarding the disposal of waste electrical and electronic equipment
(WEEE). Contact your local dealer for procedures for recycling this
equipment.
Pelco Manual C1909M (4/01)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
REGULATORY NOTICES
This equipment has been tested and found to comply with the limits of a Class B digital de-
vice, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment gener-
ates, uses, and can radiate radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interference to radio communications. How-
ever there is no guarantee that the interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try and cor-
rect the interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the re-
ceiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
If
a
warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
1. Model and serial number
Exceptions to this warranty are as noted below:
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
•
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.
Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
fixed dome products.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).
•
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.
•
•
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
REVISION HISTORY
Manual # Date
C1909M 4/01
Comments
Original version.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.
© Copyright 2001, Pelco
All rights reserved.
8
Pelco Manual C1909M (4/01)
Download from Www.Somanuals.com. All Manuals Search And Download.
|