CCC130AT
CCC132AT
CCC190AT
CCC192AT
Color TV with built-in VCR
O wner’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction 3
W elcom e to your TV/VCR owner’s m anual.
This manual describes four models: CCC130, CCC132, CCC190 and CCC192. The models may look different,
but they operate exactly the same. The CCC130 is illustrated in this manual. The features described in this
manual apply to all models unless otherwise specified.
Features
• High Quality (HQ) System
• One-Touch Recording
• Real-Time Counter
• Sleep Timer
• SmartClockTM
• SmartLockTM
• A-B Repeat Play
• Automatic Channel Setup
• Automatic Head Cleaner
• Automatic Tracking Adjustment
• Blue Background
• Closed Caption
• Daylight-Savings Time
• English or Spanish displays
• Remote Control or Front Panel • Special Effects: Forward and
menu access
Reverse Searching; Still
• S-VHS Quasi Play Back (SQPB)
• Timer Recording
• Repeat Play
• ShowGuardTM - Indefinite Timer
Recording memory
• Wake Up Timer
Safety Precautions
Warning: To prevent fire or shock hazard, do not expose this
equipment to rain or moisture.
Federal Com m unications Com m ission (FCC) W arning: Any
unauthorized changes or modifications to this equipment void the user’s
authority to operate it.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Philips Consum er Electronics recommends you use only video cassette
tapes that have the
mark. Other tapes may cause poor picture quality
and excessive deposits on the video heads that the warranty may not cover
if damage occurs.
This TV/VCR has a High Quality (HQ) system and is compatible with exist-
ing Video Home System (VHS) equipment.
Note to the Cable TV System Installer: This reminder calls the Cable
TV system installer’s attention to Article 820-40 of the National Electrical
Code, which provides guidelines for proper grounding – in particular, speci-
fying that the cable ground shall be connected to the grounding system of
the building, as close to the point of cable entry as possible.
Declaration of Conform ity
Model Numbers: CCC130AT, CCC132AT, CCC190AT, and CCC192AT
Trade Name:
Philips
Responsible Party: Philips Consumer Electronics
P.O. Box 14810
Knoxville, TN 37914-1810
(865) 521-4316
As an ENERGY STAR® Partner, Philips Consumer Electronics has determined that this product meets the ENERGY STAR® guidelines for energy
efficiency. ENERGY STAR® is a U.S. registered mark. Using products with the ENERGY STAR® label can save energy. Saving energy reduces air pollution and
lowers utility bills.
SmartClockTM, SmartLockTM, and ShowGuardTM are trademarks of Philips Consumer Electronics. Copyright 2001 Philips Consumer Electronics. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Table of Contents
Setting Up Your TV/VCR
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Before Using the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Hooking Up the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7
Turning On the TV/VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Automatic Channel Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-11
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-17
Daylight-Savings Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Time Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Description of Controls
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Remote Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22-23
Adjusting the Picture Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24-25
On-Screen Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Basic O perations
Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Recording O ptions
One-Touch Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Rerecording (Tape Duplication) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32-35
Defeat Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Playing O ptions
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
A-B Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38-39
Real-Time Counter Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Playback Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Additional Features
SmartLock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42-45
Blue Background . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Wake Up Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Volume Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Closed Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50-51
Automatic Operation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Inform ation You May Need
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54-55
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Download from Www.Somanuals.com. All Manuals Search And Download.
Before Using the TV/VCR 5
Putting Batteries in the Rem ote Control
1
1 2 3
Rem ove the battery com partm ent lid on the bottom of the
remote control by pressing the tab, then lifting the lid.
2
Place two AA batteries inside the battery com partm ent
with their and ends aligned as indicated.
+
–
3
Replace the battery com partm ent lid.
Battery Safety
● Battery Usage CAUTION - To prevent battery leakage that
may result in bodily injury or damage to the unit:
Install ALL batteries correctly, with the + and - markings on
the battery aligned as indicated on the unit;
Do not mix batteries, for example, old with new or carbon
with alkaline; and
Remove batteries when the unit will not be used for a long
time.
Recording Prevention
Video cassette tapes have record tabs to ensure you do not
erase recordings accidentally.
1
2
1
To prevent accidental recording, break off the tab with a
screwdriver.
2
To record again, cover the hole with cellophane tape.
Helpful Hints
Using the Rem ote Control
● Point the remote control at the TV/VCR’s remote sensor.
● Do not put objects between the remote control and the
TV/VCR.
• Your new product, its packaging, and
this manual contain materials that
can be recycled and reused.
Specialized companies can recycle
your product to increase the amount
of reusable materials and to mini-
mize the amount that needs to be
properly disposed.
Your product uses batteries that
should not be thrown away when
depleted but should be disposed of as
small chemical waste.
Please find out about the local regula-
tions on disposal of your old product,
batteries, manual, and packaging
when you replace existing equipment.
TV/VCR Maintenance
● In this TV/VCR, use only tapes with the
mark.
● Remove any light adhesive stick-on notes from the video cas-
sette tape before putting the tape in the TV/VCR. Removable
labels can jam the TV/VCR.
● The TV/VCR requires periodic maintenance to maintain its
excellent performance. This TV/VCR has an automatic head
cleaning system. However, the video heads will eventually
require cleaning or replacement. Only an authorized service
center should perform this service.
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Hooking Up the TV/VCR
1
Hook up your TV/VCR using one of the connections shown.
Connect a Cable signal
or an antenna to the
ANT(enna) Jack.
A.
Hooking Up Your TV/VCR
W ith a Cable Signal or
O utdoor Antenna
CCC130
ANT.
ANT.
Connect the Cable signal to
the IN Jack on the Cable Box.
B.
Connect an RF coaxial cable (75-
ohm, not supplied) to the OUT Jack
on the Cable Box and to the
Hooking Up Your TV/VCR
W ith a Cable Box
To view any channel, set the
TV/VCR to the Cable Box output
channel (channel 03 or 04). Then,
select channels at the Cable Box.
IN
ANT(enna) Jack on the TV/VCR.
OUT
CCC130
RF coaxial cable
(not supplied)
ANT.
ANT.
Rod Antenna
(not supplied)
C.
Hooking Up Your TV/VCR
W ith an Indoor Antenna
To install a rod antenna (not sup-
plied), push the stem of the antenna
into the antenna hole on the top of
the TV/VCR. Connect the antenna
wire to the ANT(enna) Jack on the
back of the TV/VCR as shown.
Extend the antenna and adjust its
length, direction, and angle for the
clearest picture.
CCC130
ANT.
ANT.
Download from Www.Somanuals.com. All Manuals Search And Download.
Hooking Up the TV/VCR (cont’d) 7
D.
Hooking Up Your TV/VCR to Another Video Source
(VCR or Cam corder)
You may need this connection if you want to copy tapes or view tapes that you are playing on the VCR or
camcorder. Select channel 00 (A/V IN) at the TV/VCR when viewing tapes that are playing on the VCR
or camcorder. Details are on page 31.
CCC130
Connect an Audio cable to the AUDIO
OUT Jack on the VCR and to the AUDIO In
Jack on the front of the TV/VCR.
Jacks on VCR
AUDIO/VIDEO OUT
3CH
IN
4CH
AUDIO VIDEO
ANT.
OUT
OUT
IN
AUDIO VIDEO
AUDIO VIDEO
STOP REW
EJECT
PLAY
F
.
F
W
D
R
E
C
CHANNEL
VOLUME
POWER
OTR
ONE
3CH
4CH
IN
AUDIO VIDEO
ANT.
OUT
OUT
AUDIO/VIDEO In Jacks
on front of TV/VCR
IN
Connect a Video cable to the VIDEO OUT Jack on the
VCR and to the VIDEO In Jack on the front of the TV/VCR.
2
W hen all other connections are com plete, plug in the TV/VCR’s power cord.
3
Before you turn on the TV/VCR, go to page eight.
Helpful Hints
• Before connecting an antenna or cable signal to the ANT(enna) Jack, make sure the pin is not bent. If the pin is
bent, straighten it as illustrated, then connect the antenna or cable signal to the ANT(enna) Jack.
• A rod antenna (not supplied) is available from Philips Service Solutions Group. The part number is 4835 303
37006. To order, call 1-800-851-8885. (This antenna will fit the CCC130 and CCC132 only.)
• Audio and video cables are not supplied.
Bent pin
Crooked Pin
Straight Pin
Plug
Cable
Download from Www.Somanuals.com. All Manuals Search And Download.
8 Turning On the TV/VCR
Before you turn on the TV/VCR, make sure batteries are in the
remote control and you have connected the TV/VCR correctly.
The instructions on this page work only when you turn on the
TV/VCR for the first time.
1 2
1
EJECT
POWER
Press the PO W ER button. The TV/VCR will come on and the
screen shown below will appear.
MENU
CLEAR
STATUS/EXIT
3
5
1
4
7
2
5
8
3
6
SELECT LANGUAGE
> ENGLISH
ON
ESPAÑOL
9
SLEEP/
SELECT KL OR
PRESS MENU TO CONTINUE
ALT.CH
WAKE UP
0
REC
/OTR
PAUSE
/STILL
PLAY
REW
F.FWD
2
Press the PLAY/K button or the STO P/L button to select
English or Spanish on-screen displays and m enus.
STOP
MUTE
4
CH.
VOL.
3
Press the MENU button. The screen shown below will appear.
SPEED
CONNECT ANTENNA OR CABLE
TO TVCR
TRACKING MEMORY
THEN PRESS
B
TO END PRESS EXIT
4
Press the F.FW D/B button to begin autom atic channel
setup. The TV/VCR will memorize all available channels. When
channels are set, CHANNELS ARE SET will appear on the screen
briefly. Then the TV/VCR will go to the lowest available channel.
If you try to set up channels when there is no antenna or cable
connected to the TV/VCR, programming will appear to take place,
but eventually a NO TV SIGNALS ... message will appear on the
screen. Connect an antenna or cable to the ANT(enna) jack on
the TV/VCR, then press the F.FWD/B button again. You may
need to follow the steps on page 10 instead.
Helpful Hints
• If you do not see any on-screen dis-
plays when you turn on the TV/VCR,
check your hookups, then try again.
If you still do not see any on-screen
displays, follow the steps on pages
nine-10 to select a language and set
up channels.
• To skip step 2, press the MENU but-
ton. All on-screen displays will be in
English. To skip step 4, press the
STATUS/EXIT button. Automatic
Channel Setup will not occur, and
CHANNELS NOT SET will appear on
the screen briefly.
5
Use the CH(annel) o/p buttons or the Num ber buttons
on the rem ote control to select a TV/VCR channel. Use
the VO L(um e) o/p buttons to adjust the sound.
When you scan channels with the CH(annel) o/p buttons, only
the memorized channels will be available. Use the Number but-
tons to select non-memorized channels.
• You cannot set up channels if you are
using a Cable Box.
• Line Input mode is channel 00.
When you select channel 00, A/V IN
will appear on the screen briefly.
Press the CH(annel) o/p buttons or
the Number buttons to select another
channel.
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Selection 9
Follow the steps below to change the language of the on-screen
displays and menus.
5 2-4
1
Press the MENU button.
EJECT
POWER
MENU
CLEAR
STATUS/EXIT
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
1
1
4
7
2
5
8
3
6
REMINDER
BRIGHTNESS
9
SLEEP/
ALT.CH
WAKE UP
0
2
Press the PLAY/▲ button or the STO P/▼ button to select
PRIM. SETUP. Then, press the F.FW D/B button.
REC
/OTR
PAUSE
/STILL
PLAY
REW
F.FWD
PRIMARY SETUP
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
STOP
MUTE
VOLUME BAR
SET CLOCK
[ON]
CH.
VOL.
SELECT KL CHOOSE
B
TO END PRESS EXIT
SPEED
3
TRACKING MEMORY
Press the PLAY/▲ button or the STO P/▼ button to
choose SELECT LANGUAGE. Then, press the F.FW D/B
button.
SELECT LANGUAGE
> ENGLISH
ESPAÑOL
ON
SELECT KL
TO END PRESS EXIT
4
Press the PLAY/▲ button or the STO P/▼ button to select
ENGLISH or ESPAÑO L (Spanish).
Helpful Hint
• If you accidentally select Spanish
and need English on-screen displays
and menus:
1) Press the MENU button.
2) Press the PLAY/o button or the
STOP/p button to select PREPARA-
CION, then press the F.FWD/B
button.
5
Press the STATUS/EXIT button.
3) Press the PLAY/o button or the
STOP/p button to select SELEC-
CION IDIOMA, then press the
F.FWD/B button.
4) Press the PLAY/o button or the
STOP/p button to select ENGLISH.
5) Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Automatic Channel Setup
Although the TV/VCR may automatically memorize the channels
you receive when you turn it on for the first time, you may set up
channels again by following the steps below.
2-3
1
EJECT
MENU
Press the MENU button.
POWER
STATUS/EXIT
CLEAR
1
4
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
1
4
7
2
5
8
3
6
REMINDER
BRIGHTNESS
9
SLEEP/
ALT.CH
WAKE UP
0
REC
/OTR
PAUSE
/STILL
2
PLAY
Press the PLAY/▲ button or the STO P/▼ button to select
PRIM. SETUP, then press the F.FW D/B button.
REW
F.FWD
STOP
MUTE
PRIMARY SETUP
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
CH.
VOL.
VOLUME BAR
SET CLOCK
[ON]
SELECT KL CHOOSE
B
TO END PRESS EXIT
SPEED
TRACKING MEMORY
3
Press the PLAY/▲ button or the STOP/▼ button to select
AUTO PROGRAMMING, then press the F.FW D/B button.
AUTO CH PROGRAMMING ... will appear on the screen. The
TV/VCR distinguishes between TV channels and cable channels auto-
matically, and the TV/VCR will memorize its available channels.
Wait for the TV/VCR to set up
channels.
4
W ait for a few m inutes. When setup is complete, CHANNELS
ARE SET will appear on the screen. Then the programming of the
lowest channel number will appear on the screen. Now, when you
press the CH(annel) o/p buttons, you will scan only through
channels you receive. You can still select non-memorized channels
using the Number buttons.
Helpful Hints
• Line Input mode will always be
channel 00. You cannot delete it.
• You can not select AUTO PRO-
GRAMMING at step 3 if you are in
Line Input mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
Automatic Channel Setup (cont’d) 11
Adding/Deleting Channels
If your channel lineup changes, you may want to add newly avail-
able channels or remove channels that are no longer available in
your area. You can use the CH(annel) o/p buttons to scroll
through only the available channels. To add or delete channels
from the TV/VCR’s memory, follow these steps.
5
2,4
EJECT
POWER
MENU
CLEAR
STATUS/EXIT
1
3
1
4
7
2
5
8
3
6
1
Press the MENU button.
9
SLEEP/
ALT.CH
WAKE UP
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
0
REC
/OTR
PAUSE
/STILL
REMINDER
PLAY
BRIGHTNESS
REW
F.FWD
STOP
MUTE
2
CH.
VOL.
Press the PLAY/o button or the STO P/p button to select
CHANNEL.
TO ADJUST PRESS { /
CH123
B
SPEED
SAVED
>
CHANNEL
SMARTLOCK
REVIEW
TRACKING MEMORY
EXIT
PRIM. SETUP
VCR PROGRAM
Helpful Hint
3
Press the CH(annel) o/p buttons or the Num ber buttons
to select the channel you want to add or delete.
• To review the memorized channels,
follow these steps.
1) Press the MENU button.
2) Press the PLAY/▲ button or the
STOP/▼ button to select PRIM.
SETUP. Press the F.FWD/B button.
3) Press the PLAY/▲ button or the
STOP/▼ button to select
TO ADJUST PRESS { /
CH23
B
SAVED
>
CHANNEL
SMARTLOCK
REVIEW
EXIT
PRIM. SETUP
VCR PROGRAM
CH MEMORY REVIEW. Press the
F.FWD/B button. A list of
programmed channels will appear on
the screen.
4
Press the F.FW D/B button or the REW (ind)/{ button to
select SAVED (to add that channel) or DELETED (to
delete that channel).
4) If all the programmed channels
don’t fit on the screen, press the
F.FWD/B button. If you do not press
the F.FWD/B button within 10
seconds, the remaining channels will
appear on the screen. (If there are
no remaining channels, the previous
menu will appear.) Or press the
REW(ind)/{ button to see the
previous screen of channels.
5) Press the STATUS/EXIT button
once or twice.
Repeat steps 3-4 to add or delete other channels.
5
Press the STATUS/EXIT button.
Programming of the channel you added or deleted will appear.
Download from Www.Somanuals.com. All Manuals Search And Download.
12 Setting the Clock
There are three ways to set the clock: Manually, with Automatic
PBS Channel Selection, or with Manual PBS Channel Selection.
With manual clock setting, you tell the TV/VCR the current time.
With Automatic or Manual PBS Channel Selection, the TV/VCR
gets the time from your local PBS station.
If you use either Manual PBS Channel Selection or Automatic PBS
Channel Selection, follow the steps on page 19 to have the
TV/VCR maintain the clock according to your Time Zone.
Cable Box users m ust set the clock m anually.
To set the clock manually, follow the steps on pages 12-13. To set
the clock using Automatic PBS Channel Selection, follow the steps
on pages 14-15. To set the clock using Manual PBS Channel
Selection, follow the steps on pages 16-17.
2-3
EJECT
MENU
POWER
STATUS/EXIT
CLEAR
1
1
4
7
2
5
8
3
6
9
SLEEP/
ALT.CH
WAKE UP
Before you begin, make sure:
0
● You have connected and turned on the TV/VCR. Details are on
pages six-eight.
REC
/OTR
PAUSE
/STILL
PLAY
● Channels are set. Details are on page 10.
● You make each entry within 60 seconds of the previous entry.
REW
F.FWD
STOP
MUTE
CH.
VOL.
Manual Clock Setting
1
SPEED
Press the MENU button.
TRACKING MEMORY
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
PRESS
B
REMINDER
BRIGHTNESS
2
Press the PLAY/▲ button or the STO P/▼ button to select
PRIM. SETUP. Then, press the F.FW D/B button.
PRIMARY SETUP
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
VOLUME BAR
SET CLOCK
[ON]
SELECT KL CHOOSE
B
TO END PRESS EXIT
3
Helpful Hints
Press the PLAY/▲ button or the STO P/▼ button to select
SET CLO CK. Then, press the F.FW D/B button.
• Entries that do not match the
TV/VCR’s calendar will cause a
question mark (?) to appear on the
screen.
• To make corrections while you are
setting the clock, press the CLEAR
button until the space for the num-
ber you want to correct is flashing.
Then enter the correct number.
SET CLOCK
> AUTO CLOCK
SET MANUAL CLOCK
DAYLIGHT SVG.TIME
SET TIME ZONE
[AUTO]
[ON]
[ON]
TO CONTINUE PRESS MENU
SELECT KL CHOOSE
TO END PRESS EXIT
B
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Clock (cont’d) 13
4
7 5-6
Press the PLAY/o button or the STO P/p button to select
SET MANUAL CLO CK, then press the F.FW D/B button.
SET MANUAL CLOCK
EJECT
TIME – – : – –
POWER
MENU
CLEAR
STATUS/EXIT
DATE – – / – – / – – – –
1
4
7
2
5
8
3
6
TO END PRESS EXIT
9
SLEEP/
ALT.CH
WAKE UP
0
5
Press two Num ber buttons for the hour(s) and two
Num ber buttons for the m inute(s). Then press 1 for AM
or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.
REC
/OTR
PAUSE
/STILL
PLAY
REW
F.FWD
4
SET MANUAL CLOCK
STOP
MUTE
TIME
09 : 30 PM
CH.
VOL.
MONTH
– – / – – / – – – –
TO CORRECT PRESS CLEAR
TO END PRESS EXIT
SPEED
TRACKING MEMORY
6
Press two Num ber buttons for the m onth, two Num ber
buttons for the day, and two Num ber buttons for the
year. For example, for July 1, 2001, press 07, 01, 01. The day of
the week will appear automatically.
SET MANUAL CLOCK
TIME
09 : 30 PM
DATE
07 / 01 / 2001
SUNDAY
TO CORRECT PRESS CLEAR
TO END PRESS EXIT
7
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
14 Setting the Clock (cont’d)
Autom atic PBS Channel Selection
1 2-4
1
Press the MENU button.
EJECT
POWER
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
PRESS
B
MENU
CLEAR
STATUS/EXIT
4
REMINDER
1
4
7
2
5
8
3
6
BRIGHTNESS
9
SLEEP/
ALT.CH
WAKE UP
2
0
Press the PLAY/▲ button or the STO P/▼ button to select
PRIM. SETUP. Then, press the F.FW D/B button.
REC
/OTR
PAUSE
/STILL
PLAY
PRIMARY SETUP
REW
F.FWD
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
VOLUME BAR
SET CLOCK
STOP
MUTE
[ON]
CH.
VOL.
SELECT KL CHOOSE
TO END PRESS EXIT
B
SPEED
3
Press the PLAY/▲ button or the STO P/▼ button to select
SET CLO CK. Then, press the F.FW D/B button.
TRACKING MEMORY
SET CLOCK
> AUTO CLOCK
SET MANUAL CLOCK
DAYLIGHT SVG.TIME
SET TIME ZONE
[AUTO]
[ON]
[ON]
TO CONTINUE PRESS MENU
SELECT KL CHOOSE
TO END PRESS EXIT
B
4
If ON appears beside AUTO CLOCK, press the MENU
button.
If OFF appears beside AUTO CLOCK, press the PLAY/o
button or the STOP/p button to select AUTO CLOCK,
then press the F.FW D/B button so that ON appears to the
right of AUTO CLOCK. Then, press the MENU button.
AUTO CLOCK
AUTO CLOCK USES
PBS CHANNEL DATA
>
SET PBS CH. AUTO
SET PBS CH. MANUAL
SELECT KL CHOOSE
B
TO END PRESS EXIT
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Clock (cont’d) 15
Wait for the TV/VCR to find
the time.
5
6
Press the PLAY/▲ button or the STOP/▼ button to select
SET PBS CH. AUTO. Then, press the F.FW D/B button.
SET AUTO CLOCK
EJECT
TIME
– – : – –
POWER
MENU
CLEAR
STATUS/EXIT
DATE
– – / – – / – – – –
NOW SEARCHING
TO END PRESS EXIT
1
4
7
2
5
8
3
6
7
9
SLEEP/
6
ALT.CH
WAKE UP
0
NOW SEARCHING flashes on the TV/VCR screen.
REC
/OTR
PAUSE
/STILL
PLAY
7
REW
F.FWD
W hen the TV/VCR finds the PBS channel, the tim e will
appear on the screen. Press the STATUS/EXIT button.
SET AUTO CLOCK
5
STOP
MUTE
CH.
VOL.
TIME
06 : 30 PM
DATE
07 / 01 / 2001
SUNDAY
SPEED
TO END PRESS EXIT
TRACKING MEMORY
● If CANNOT FIND CLOCK DATA flashes on the TV/VCR
screen, you will be prom pted to turn off the TV/VCR.
Turn off the TV/VCR. Leave it off for several minutes. When
you turn on the TV/VCR again, the clock will be set.
SET AUTO CLOCK
TIME
– – : – –
DATE
– – / – – / – – – –
CANNOT FIND CLOCK DATA
TO END PRESS EXIT
Helpful Hints
• To display the time on the TV/VCR
screen, press the STATUS/EXIT but-
ton. Details are on page 26.
• You cannot use the AUTO CLOCK
feature if you don’t receive a PBS
channel that carries a time signal in
your area. Set the clock manually.
Download from Www.Somanuals.com. All Manuals Search And Download.
16 Setting the Clock (cont’d)
Manual PBS Channel Selection
1 2-4
1
Press the MENU button.
EJECT
POWER
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
PRESS
B
MENU
CLEAR
STATUS/EXIT
4
1
4
7
2
5
8
3
6
REMINDER
BRIGHTNESS
9
SLEEP/
ALT.CH
WAKE UP
2
0
Press the PLAY/▲ button or the STO P/▼ button to select
PRIM. SETUP. Then, press the F.FW D/B button.
REC
/OTR
PAUSE
/STILL
PLAY
PRIMARY SETUP
REW
F.FWD
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
STOP
MUTE
VOLUME BAR
SET CLOCK
[ON]
CH.
VOL.
SELECT KL CHOOSE
B
TO END PRESS EXIT
SPEED
3
TRACKING MEMORY
Press the PLAY/▲ button or the STO P/▼ button to select
SET CLO CK. Then, press the F.FW D/B button.
SET CLOCK
> AUTO CLOCK
SET MANUAL CLOCK
DAYLIGHT SVG.TIME
SET TIME ZONE
[AUTO]
[ON]
[ON]
TO CONTINUE PRESS MENU
SELECT KL CHOOSE
TO END PRESS EXIT
B
4
If ON appears beside AUTO CLOCK, press the MENU
button.
If OFF appears beside AUTO CLOCK, press the PLAY/o
button or the STOP/p button to select AUTO CLOCK,
then press the F.FW D/B button so that ON appears to the
right of AUTO CLOCK. Then, press the MENU button.
AUTO CLOCK
AUTO CLOCK USES
PBS CHANNEL DATA
>
SET PBS CH. AUTO
SET PBS CH. MANUAL
SELECT KL CHOOSE
B
TO END PRESS EXIT
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Clock (cont’d) 17
Wait for the TV/VCR to
find the time.
5
7
Press the PLAY/▲ button or the STO P/▼ button to
select SET PBS CH. MANUAL. Then, press the F.FW D/B
button.
AUTO CLOCK (PBS) CH 02
EJECT
MENU
POWER
STATUS/EXIT
CLEAR
TIME
– – : – –
DATE
– – / – – / – – – –
1
4
7
2
5
8
3
6
8
5
SELECT CHANNEL NUMBER
TO END PRESS EXIT
6
9
SLEEP/
ALT.CH
WAKE UP
0
6
Use the Num ber buttons to select your PBS station.
REC
/OTR
PAUSE
/STILL
PLAY
AUTO CLOCK (PBS) CH 12
REW
F.FWD
TIME
– – : – –
DATE
– – / – – / – – – –
STOP
MUTE
NOW SEARCHING
TO END PRESS EXIT
CH.
VOL.
SPEED
7
TRACKING MEMORY
NOW SEARCHING flashes on the TV/VCR screen.
8
W hen the TV/VCR finds the clock data, the tim e will
appear on the screen. Press the STATUS/EXIT button.
AUTO CLOCK (PBS) CH 12
TIME
06 : 30 PM
DATE
07 / 01 / 2001
SUNDAY
TO END PRESS EXIT
● If CANNO T FIND CLO CK DATA flashes on the
TV/VCR screen and you know another PBS channel,
press the PLAY/▲ button or the STO P/▼ button to
choose SELECT NEW PBS CH. Then, press the
F.FW D/B button. Repeat step 6.
● If CANNO T FIND CLO CK DATA flashes on the
TV/VCR screen and you do not know another channel,
press the PLAY/▲ button or the STO P/▼ button to
select SET PBS CH. AUTO. Then, press the F.FW D/B
button. The TV/VCR will search for the PBS channel automati-
cally.
• If the TV/VCR finds the PBS channel, the time will appear on
the screen.
• If the TV/VCR does not find the PBS channel, you will be
prompted to turn off the TV/VCR. Leave it off for several min-
utes. When you turn on the TV/VCR again, the time will be set.
Helpful Hints
• If you have an Antenna hookup, you
may select channels 2-69 at step 6.
If you have a cable connection, you
may select channels 1-125 at step
6. Details about available memo-
rized channels are on page 11.
• To display the time on the TV/VCR
screen, press the STATUS/EXIT but-
ton. Details are on page 26.
Download from Www.Somanuals.com. All Manuals Search And Download.
18 Daylight-Savings Time
When the Daylight-Savings Time feature is ON, the TV/VCR clock
will automatically move forward one hour on the first Sunday in
April and move back one hour on the last Sunday in October.
To turn Daylight-Savings Time ON or OFF, follow the steps
below.
5 2-4
EJECT
POWER
1
MENU
CLEAR
STATUS/EXIT
Press the MENU button.
1
1
4
7
2
5
8
3
6
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
PRESS
B
9
SLEEP/
ALT.CH
WAKE UP
REMINDER
0
BRIGHTNESS
REC
/OTR
PAUSE
/STILL
PLAY
REW
F.FWD
2
Press the PLAY/▲ button or the STO P/▼ button to select
PRIM. SETUP. Then, press the F.FW D/B button.
STOP
MUTE
CH.
VOL.
PRIMARY SETUP
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
VOLUME BAR
SET CLOCK
[ON]
SPEED
SELECT KL CHOOSE
B
TRACKING MEMORY
TO END PRESS EXIT
3
Press the PLAY/▲ button or the STO P/▼ button to select
SET CLO CK. Then, press the F.FW D/B button.
SET CLOCK
> AUTO CLOCK
SET MANUAL CLOCK
DAYLIGHT SVG.TIME
SET TIME ZONE
[AUTO]
[ON]
[ON]
TO CONTINUE PRESS MENU
SELECT KL CHOOSE
TO END PRESS EXIT
B
4
Press the PLAY/▲ button or the STO P/▼ button to select
DAYLIGHT SVG.TIME. Then, press the F.FW D/B button
so that O N or O FF appears beside DAYLIGHT SVG.
TIME (Daylight Savings Tim e).
5
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Time Zone 19
When you set the clock using AUTO CLOCK, specify your time zone.
The TV/VCR will maintain the clock according to your time zone.
1 2-5
1
Press the MENU button.
EJECT
POWER
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
PRESS
B
MENU
CLEAR
STATUS/EXIT
REMINDER
BRIGHTNESS
1
4
7
2
5
8
3
6
6
9
SLEEP/
2
ALT.CH
WAKE UP
0
Press the PLAY/▲ button or the STO P/▼ button to select
REC
/OTR
PAUSE
/STILL
PRIM. SETUP. Then, press the F.FW D/B button.
PLAY
PRIMARY SETUP
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
REW
F.FWD
STOP
MUTE
VOLUME BAR
SET CLOCK
[ON]
CH.
VOL.
SELECT KL CHOOSE
B
TO END PRESS EXIT
3
SPEED
Press the PLAY/▲ button or the STO P/▼ button to select
SET CLO CK. Then, press the F.FW D/B button.
TRACKING MEMORY
SET CLOCK
> AUTO CLOCK
SET MANUAL CLOCK
DAYLIGHT SVG.TIME
SET TIME ZONE
[AUTO]
[ON]
[ON]
TO CONTINUE PRESS MENU
SELECT KL CHOOSE
TO END PRESS EXIT
B
4
Press the PLAY/▲ button or the STO P/▼ button to select
SET TIME ZO NE. Then, press the F.FW D/B button.
SET TIME ZONE
> AUTO
ATLANTIC
[ON]
EASTERN
CENTRAL
MOUNTAIN
PACIFIC
ALASKA
HAWAII
SELECT KL
TO CONTINUE PRESS MENU
Helpful Hints
5
• If you select AUTO at step 5, the
TV/VCR will set the clock according
to the time zone data of the PBS
station it finds.
Press the PLAY/▲ button or the STO P/▼ button to select
your tim e zone.
• You cannot select SET TIME ZONE
at step 4 if AUTO CLOCK is OFF.
6
Press the MENU button, then press the STATUS/EXIT
button.
Download from Www.Somanuals.com. All Manuals Search And Download.
20 Front Panel
CCC130
Cassette Com partm ent
Insert a video cassette tape here.
W ireless Rem ote Sensor
Receives a signal from your remote control so
you can operate the TV/VCR from a distance.
STO P/EJECT Button
Press once to stop the tape. When playback
is stopped, press to eject the tape. Press to
select an item in the menu.
VIDEO In Jack
Connect this jack to the video out jack of a
camcorder or a VCR. Details are on page 31.
AUDIO In Jack
Connect this jack to the audio out jack of a
camcorder or a VCR. Details are on page 31.
EARPHO NE Jack
AUDIO VIDEO
STOP REW
EJECT
PLAY
F.FWD REC
OTR
CHANNEL
VOLUME
POWER
EARPHONE
Connect earphones (not supplied) here for
personal listening.
REW (ind) Button
VOLUME o/p
Buttons
Press to adjust the
sound level.
Press the CHANNEL
o button and the
VOLUME p button
on the TV/VCR at
the sam e tim e to
display the main menu.
Press again to remove
the main menu.
When tape playback is stopped, press to rewind
the tape at high speed. During playback, press to
rewind the tape while the picture stays on the
screen. Press to change a setting of a menu item
(for example, to adjust the BRIGHTNESS) or to
return to a previous menu.
PLAY Button
Press to play a tape. Details are on page 28.
Press to release Search or Still mode and
return to normal playback. Details are on page
41. Press to select an item in the menu.
F.FW D (Fast Forward) Button
When tape playback is stopped, press to fast
forward the tape at high speed. During play-
back, press to fast forward the tape while the
picture stays on the screen. Press to change a
setting of a menu item (for example, to adjust
the BRIGHTNESS) or to advance to the next
menu.
CHANNEL o/p
Buttons
Press to scan through
the TV/VCR’s memo-
rized channels. During
tape playback, press to
adjust the tracking.
Details are on page 52.
Press the CHANNEL
o button and the
VOLUME p button
on the TV/VCR at
the sam e tim e to
display the main menu.
Press again to remove
the main menu.
REC(ord)/O TR Button
Press once to start a recording. Details are on
page 29. Press repeatedly to start a One-
Touch Recording (an immediate timed
recording, 30 minutes to eight hours long) of
the channel you are watching. Details are on
page 30.
Record Light
This light appears during a recording. It flashes slowly when
the TV/VCR power is off for a timer recording. It blinks
rapidly when a recording is paused or when the power is off
for a timer recording, but there is no tape in the TV/VCR. It
will blink rapidly two minutes before a timer recording is set
to begin if the TV/VCR power is on.
PO W ER Button
Press to turn the power on or off.
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel 21
CCC130
ANT.
ANT(enna) Jack
Connect your antenna or cable here.
AC Power Cord
Details are on page six.
Connect to a standard AC outlet to
supply power to the TV/VCR.
Antenna Hole
Connect the stem of an indoor antenna
here. Details are on page six.
Download from Www.Somanuals.com. All Manuals Search And Download.
22 Remote Control Buttons
CLEAR Button
Press to erase incorrect data when programming TV/VCR func-
tions. Also, press to reset the real-time counter to 0:00:00.
Details are on page 40.
PO W ER Button
Press to turn on or off the TV/VCR.
EJECT Button
Press to eject the tape.
EJECT
MENU
POWER
STATUS/EXIT
Num ber Buttons
CLEAR
Use to select channels and to program TV/VCR functions (such as
setting the clock).
● Cable Users
1
4
7
2
5
8
3
6
Enter channel numbers as a two-digit number for the quickest results.
For example, to select channel 6, press 0,6. If you only press the
Number 6 button, channel 6 will be selected after a brief delay. (There
also may be a brief delay when you select channels 10, 11, and 12.) If
you want to select channels 100 and above, enter channel numbers as a
three-digit number. For example, to select channel 117, press 1, 1, 7.
● Antenna Users
Enter channel numbers as a two-digit number for the quickest results.
For example, to select channel 5, press 0,5. If you only press the
Number 5 button, channel 5 will be selected after a brief delay. You may
only select channels 2-69.
9
SLEEP/
ALT.CH
WAKE UP
0
REC
/OTR
PAUSE
/STILL
PLAY
REW
F.FWD
STOP
MUTE
SLEEP/W AKE UP Button
Press to set the Sleep Timer. Details are on page 47. Press to set the
Wake Up Timer. Details are on page 48.
CH.
VOL.
PLAY/▲ Button
Press to play a tape. Details are on page 28. Press to release Search
or Still mode and return to normal playback. Details are on page 41.
Press to select an item in the menu.
SPEED
MUTE Button
TRACKING MEMORY
Press to eliminate the TV/VCR’s sound. Press again to return to
the previous volume level.
SPEED Button
Press to select the recording speed (SP or SLP).
VOL(um e) o/p Buttons
Press to adjust the sound level. If you press the VOL(ume) o/p
buttons when the sound is muted, the sound will be restored.
F.FW D/B Button
When tape playback is stopped, press to fast forward the tape at high
speed. During tape playback, press to fast forward the tape while the
picture stays on the screen. Details are on page 41.
Press to change the setting of a menu item or to go to the next menu.
ALT. CH (Alternate Channel) Button
Press to return to the TV channel you were viewing immediately
before switching to your current channel.
Helpful Hint
• Buttons that are shaded in the illustration light up for five seconds when you press any button on the remote
control (CCC132 and CCC192 only).
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Buttons (cont’d) 23
MENU Button
Press to display the main menu. You also may use the buttons on
the front of the TV/VCR to access the main menu. Details are on
page 20.
EJECT
MENU
POWER
STATUS/EXIT
STATUS/EXIT Button
CLEAR
Press to access or remove the status display. Details are on page 26.
Press to remove the menu.
1
4
7
2
5
8
3
6
REC(ord)/O TR Button
Press once to start a recording. Details are on page 29. Or, press
repeatedly to start a One-Touch Recording (an immediate timed
recording, 30 minutes to eight hours long) of the channel you are
watching. Details are on page 30.
9
SLEEP/
ALT.CH
WAKE UP
0
REW (ind)/{ Button
When tape playback is stopped, press to rewind the tape at high speed.
During tape playback, press to rewind the tape while the picture stays on
the screen. Details are on page 41.
REC
/OTR
PAUSE
/STILL
PLAY
REW
F.FWD
Press to change a setting of a menu item or to return to a previous menu.
STOP
MUTE
STO P/▼ Button
Press to stop the tape. Press to select an item in the menu.
CH.
VOL.
CH(annel) o/p Buttons
Press to scan through the TV/VCR’s available channels.
SPEED
TRACKING o/p Buttons
Press during tape playback to adjust the tracking. Details are on
TRACKING MEMORY
page 52.
MEMO RY Button
Press to memorize a tape position at which you set the real-time
counter to 0:00:00. Details are on page 40. Or, press to memorize
the start and end positions on a tape when setting up A-B Repeat
Play. Details are on pages 38-39.
PAUSE/STILL Button
During recording, press to temporarily stop the recording. Press
again to resume recording. Details are on page 29. You cannot
pause a One-Touch Recording.
During tape playback, press to freeze the picture (still). Each time
you press the PAUSE/STILL button, the noise lines will change
position on the screen. Details are on page 41.
Helpful Hint
• Buttons that are shaded in the illustration light up for five seconds when you press any button on the remote
control (CCC132 and CCC192 only).
Download from Www.Somanuals.com. All Manuals Search And Download.
24 Adjusting the Picture Controls
Follow these steps to adjust the TV/VCR’s brightness, picture,
color, tint, and sharpness.
4 2-3
1
Press the MENU button.
EJECT
POWER
TO ADJUST PRESS { /
B
MENU
CLEAR
STATUS/EXIT
>
BRIGHTNESS
PICTURE
COLOR
1
1
4
7
2
5
8
3
6
TINT
SHARPNESS
TV RESET
9
SLEEP/
ALT.CH
WAKE UP
0
2
REC
/OTR
PAUSE
/STILL
Press the PLAY/▲ button or the STO P/▼ button to select
the desired control (BRIGHTNESS, for exam ple).
PLAY
REW
F.FWD
STOP
MUTE
3
CH.
VOL.
Press the REW (ind)/{ button or the F.FW D/B button to
adjust the picture control. (Refer to the chart on page 25.)
SPEED
4
TRACKING MEMORY
W hen you finish, press the STATUS/EXIT button.
Helpful Hints
• The menus on page 25 will disap-
pear if you do not make adjustments
within 60 seconds.
• The original settings will probably give
you the best picture quality.
• To reset the picture controls to the
original settings, press the MENU
button, then press the PLAY/▲ but-
ton or the STOP/▼ button to select
TV RESET, then press the F.FWD/B
button. TV RESET COMPLETED will
appear on the screen briefly.
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Picture Controls (cont’d) 25
Decrease
decreased brightness
decreased contrast
paler
Increase
increased brightness
increased contrast
more brilliant
more green
BRIGHTNESS
PICTURE
CO LO R
TINT
SHARPNESS
more purple
softer
clearer
CCC130
Press the REW(ind)/{
button to decrease a
picture control. Press
the F.FWD/B button
to increase a picture
control.
AUDIO VIDEO
STOP REW
EJECT
PLAY
CHANNEL
VOLUME
POWER
EARPHONE
TO ADJUST PRESS { /
B
TO ADJUST PRESS { /
B
TO ADJUST PRESS { /
B
BRIGHTNESS
BRIGHTNESS
PICTURE
COLOR
TINT
SHARPNESS
TV RESET
>
BRIGHTNESS
PICTURE
COLOR
>
PICTURE
COLOR
TINT
SHARPNESS
TV RESET
>
TINT
SHARPNESS
TV RESET
TO ADJUST PRESS{ /
B
TO ADJUST PRESS { /
B
BRIGHTNESS
PICTURE
COLOR
TINT
SHARPNESS
TV RESET
BRIGHTNESS
PICTURE
COLOR
TINT
SHARPNESS
TV RESET
>
>
Press the STOP/▼
button
Press the PLAY/▲
button
Download from Www.Somanuals.com. All Manuals Search And Download.
26 On-Screen Status Displays
A status display will appear when you press the STATUS/EXIT
button or certain function buttons. The contents of the status dis-
play will vary. To choose the status display mode, follow the steps
below.
If you select STATUS O N, then select CO UNTER O NLY
O FF:
● Whenever you press the STOP/p button or the PLAY/o but-
ton, the status display will appear for five seconds. Portions of
the status display also may appear when you press other func-
tion buttons.
If you select STATUS O N, then select CO UNTER O NLY
O N:
Current
Tape
Channel
Time
Function
12:00 AM
CH10
STOP
● Whenever you press the PLAY/o button, the status display will
appear for five seconds. After five seconds, only the counter will
remain on the screen. Portions of the status display also may
appear when you press other function buttons.
If you select STATUS O FF:
● The status display will not appear when you press function but-
tons. You must press the STATUS/EXIT button to see the sta-
tus display.
SLP
M 1:23:45
Counter
and
Counter
Memory
Tape
Speed
1
Press the MENU button.
2
Press the PLAY/▲ button or the STO P/▼ button to select
VCR SETUP, then press the F.FW D/B button.
3
Press the PLAY/▲ button or the STO P/▼ button to select
O N-SCREEN MO DE, then press the F.FW D/B button.
4
Press the PLAY/o button or the STO P/p button to select
STATUS, then press the F.FW D/B button so that O N or
O FF appears beside STATUS.
ON-SCREEN MODE
> STATUS
[ON]
[OFF]
COUNTER ONLY
SELECT KL CHOOSE
B
TO END PRESS EXIT
5
If you set STATUS to O FF, go to step 6. If you set STA-
TUS to O N, press the PLAY/o button or the STO P/p
button to select CO UNTER O NLY, then press the
F.FW D/B button so that O N or O FF appears beside it.
Helpful Hint
• You cannot view closed captions
during recording or tape playback if
COUNTER ONLY is ON. Details are
on pages 50-51.
6
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Reminder 27
2-3
POWER
The channel number will remain on the screen at all times when
you set REMINDER to ON. The exception is when closed cap-
tioning is selected.
4
Set REMINDER to ON or OFF by following the steps below.
EJECT
MENU
CLEAR
STATUS/EXIT
1
1
1
4
7
2
5
8
3
6
Press the MENU button.
9
SLEEP/
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
ALT.CH
WAKE UP
0
REC
/OTR
PAUSE
/STILL
REMINDER
BRIGHTNESS
PLAY
REW
F.FWD
STOP
MUTE
2
Press the PLAY/▲ button or the STO P/▼ button to select
REMINDER.
CH.
VOL.
TO ADJUST PRESS { /
B
SPEED
OFF
>
REMINDER
BRIGHTNESS
PICTURE
COLOR
TRACKING MEMORY
TINT
SHARPNESS
3
Press the REW (ind)/{ button or the F.FW D/B button to
select O N or O FF. Each press of the REW(ind)/{ button or
the F.FWD/B button turns REMINDER ON or OFF.
TO ADJUST PRESS { /
B
CH12
ON
>
REMINDER
BRIGHTNESS
PICTURE
COLOR
TINT
SHARPNESS
4
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
28 Playing
Follow the steps below to play a tape.
Insert a tape in the TV/VCR.
1
5
1
Insert a tape in the TV/VCR. The power will come on. If the
tape’s record tab is missing, playback should start automatically.
EJECT
POWER
MENU
CLEAR
STATUS/EXIT
1
4
7
2
5
8
3
6
2
If playback does not start autom atically, press the
PLAY/▲ button to start playback.
9
SLEEP/
ALT.CH
WAKE UP
0
3
REC
PAUSE
/STILL
/OTR
Press the STO P/▼ button to stop playback.
PLAY
2
3
REW
F.FWD
4
STOP
MUTE
4
Press the REW (ind)/{ button to rewind the tape.
CH.
VOL.
5
W hen the tape finishes rewinding, press the EJECT but-
ton to rem ove the tape.
SPEED
TRACKING MEMORY
S-VHS Quasi Play Back (SQPB)
SQPB allows you to view a tape recorded in S-VHS format. An S-
VHS format tape will play the same as a normal format tape. This
unit detects whether the tape is in S-VHS format or normal format.
Helpful Hints
• If the tape you want to play is
already in the TV/VCR, turn on the
TV/VCR power, then press the
PLAY/▲ button.
• Playback features and options are
on pages 37-41.
• When you play an S-VHS format
tape, you can not get the high reso-
lution that would be available on an
S-VHS VCR. Noise lines (black and
white streaks) may appear in the
picture.
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording 29
Read and follow the steps below to record a TV program.
1
1
Place a tape with its record tab intact (see page five) in the
TV/VCR. The power will come on. Or, if the tape is already in
the TV/VCR, press the POW ER button to turn on the
TV/VCR, if necessary.
EJECT
MENU
POWER
CLEAR
STATUS/EXIT
1
4
7
2
5
8
3
6
2
Press the SPEED button until the desired tape speed
appears on the TV/VCR screen. See tape speed details below.
9
SLEEP/
ALT.CH
WAKE UP
0
3
Use the CH(annel) o/p buttons or the Num ber buttons to
select the channel you want to record. You can not change
channels during recording.
REC
PAUSE
/STILL
4
5
6
/OTR
PLAY
3
REW
F.FWD
STOP
MUTE
4
CH.
VOL.
Press the REC(ord)/OTR button once to start recording.
The Record light will glow.
● If there is not a tape in the TV/VCR, NO CASSETTE flashes on
the screen briefly.
SPEED
● If the tape does not have a record tab, PROTECTED CASSETTE
CANNOT RECORD flashes on the screen briefly. The TV/VCR
will eject the tape. Insert another tape.
2
TRACKING MEMORY
5
To pause the recording (for exam ple, during com m ercials),
press the PAUSE/STILL button. The Record light will flash. To
resum e recording, press the PAUSE/STILL button again or
the REC(ord)/OTR button. The Record light will glow.
6
To stop recording, press the STOP/▼ button.
Helpful Hints
• You cannot record one channel while
watching another.
• Recording options are on pages
30-36.
• You cannot record if DEFEAT
RECORDING is ON. (REC
DEFEATED will flash on the screen.)
Details are on page 36.
Tape Speeds
This chart shows the recording/playback time for three types of
video cassettes (T160, T120, and T60). There are three playback
speeds: SP, LP, and SLP. A tape will play only in the speed in which
it was recorded. When recording, you can change the tape speed
using the SPEED button. You cannot record in LP speed.
The slower the speed, the more programming you can fit on the
tape. SLP is the slowest speed.
• If you pause a recording for more
than five minutes, the TV/VCR will
switch to Stop mode automatically to
protect the video cassette tape from
damage.
• You can change the tape speed with
the SPEED button while a recording is
in progress, but some distortion may
appear on the tape.
Cassette type / Playback Time
Tape Speed
SP(Standard Play)
T160
2 hrs.
40 mins.
5 hrs.
T120
T60
2 hrs.
1 hr.
LP(Long Play)
(playback only)
4 hrs.
6 hrs.
2 hrs.
3 hrs.
20 mins.
SLP(Super Long Play)
8 hrs.
Download from Www.Somanuals.com. All Manuals Search And Download.
30 One-Touch Recording
A One-Touch Recording (OTR) is an immediate timed recording
from 30 minutes to eight hours long.
Before you begin, make sure:
● Channels are set. Details are on page 10.
● A tape is in the TV/VCR. The record tab must be intact.
Press the STOP/EJECT but-
ton on the TV/VCR to stop
the OTR.
4
1
EJECT
POWER
MENU
CLEAR
STATUS/EXIT
1
1
4
7
2
5
8
3
6
Use the CH(annel) o/p buttons or the Num ber buttons to
select the channel you want to record.
9
SLEEP/
ALT.CH
WAKE UP
0
2
REC
PAUSE
/STILL
3
2
/OTR
Press the SPEED button until the desired recording speed
(SP or SLP) appears on the screen. Details are on page 29.
PLAY
REW
F.FWD
STOP
MUTE
3
CH.
VOL.
Press the REC(ord)/OTR button repeatedly until the desired
recording length appears in the upper right corner of the screen.
Recording will begin immediately. The Record light will appear.
SPEED
OTR
LENGTH 0:30
CH12
TRACKING MEMORY
LENGTH
CANCEL
:
:
PRESS OTR
PRESS CLEAR
4
To stop an OTR before recording is finished, press the
STOP/EJECT button on the TV/VCR.
Or, press the REC(ord)/OTR button, then press the CLEAR
button, then press the STOP/▼ button on the rem ote con-
trol.
Helpful Hints
• To check the time remaining for an
OTR, press the STATUS/EXIT button.
• To change the recording length while
an OTR is in progress, press the
REC(ord)/OTR button until the
desired recording length appears on
the screen.
If the end of a tape is reached during an OTR, recording will stop.
The TV/VCR will turn itself off and eject the tape. The Record light
will flash rapidly.
The TV/VCR will turn off at the end of the OTR.
• You can not pause an OTR.
• To cancel an OTR but continue
recording, press the REC(ord)/OTR
button, then press the CLEAR button.
• You cannot record if DEFEAT
RECORDING is ON. Details are on
page 36.
• You can change the tape speed with
the SPEED button while a recording is
in progress, but some distortion may
appear on the tape.
Download from Www.Somanuals.com. All Manuals Search And Download.
Rerecording (Tape Duplication) 31
AUDIO and VIDEO OUT Jacks on source unit
(VCR or Camcorder)
CCC130
AUDIO VIDEO
STOP
R
EJECT
EARPHONE
VIDEO AUDIO
OUT
IN
Audio Cable from
AUDIO OUT to AUDIO In
AUDIO and VIDEO In
Jacks on TV/VCR
Video Cable from
VIDEO OUT to VIDEO In
1
Make the connections shown above, using audio and video
cables (not supplied). Connect the source unit (VCR or
cam corder) to a power source after connections are m ade.
2
The source unit will play your tape. Insert a prerecorded tape in
the source unit. If playback begins, press the STOP button on the
unit.
3
The TV/VCR will record your tape. Insert a blank tape in the
TV/VCR. Make sure the tape’s record tab is intact. The TV/VCR
power will turn on automatically.
4
Point the TV/VCR rem ote control at the TV/VCR. Press
Num ber buttons 0, 0 so that A/V IN appears on the screen.
The TV/VCR is now in Line Input mode.
5
Point the TV/VCR rem ote control at the TV/VCR. Press the
SPEED button until the desired tape speed (SP or SLP)
appears on the screen.
Helpful Hints
• Unauthorized recording of copyright-
ed television programs, video tapes,
or other materials may infringe on
the rights of copyright owners and
violate copyright laws.
• Different brands of equipment may
operate differently.
6
Press the PLAY button on the source unit and the
REC(ord)/OTR button on your TV/VCR at the sam e tim e.
Copying will begin.
• Make sure all connections are secure.
Otherwise, you may not record both
picture and sound.
• Programs that are copyright
protected may not record clearly.
7
To stop copying, press the STOP/EJECT button on the
TV/VCR, then stop the tape on the source unit (VCR or
cam corder).
Download from Www.Somanuals.com. All Manuals Search And Download.
32 Timer Recording
Follow the steps below to program the TV/VCR to record TV
programs while you’re away from home. The TV/VCR will turn
itself on, record, and turn itself off automatically. Before you begin,
make sure:
● The clock is set. If not, CLOCK MUST BE SET appears, fol-
lowed by the SET CLOCK menu. Details are on pages 12-17.
● Channels are set. Details are on page 10.
● A tape is in the TV/VCR. Make sure the tape’s record tab is
intact and the tape is long enough to record the program.
Com plete each step within 60 seconds of com pleting the
previous step. If you don’t, you m ay start again at step 1.
2-3
EJECT
MENU
POWER
STATUS/EXIT
CLEAR
1
1
4
7
2
5
8
3
6
9
SLEEP/
ALT.CH
WAKE UP
0
1
REC
/OTR
PAUSE
/STILL
Press the MENU button.
PLAY
REW
F.FWD
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
STOP
MUTE
CH.
VOL.
REMINDER
BRIGHTNESS
SPEED
2
Press the PLAY/▲ button or the STO P/▼ button to select
VCR PRO GRAM, then press the F.FW D/B button.
TRACKING MEMORY
VCR PROGRAM
> ONCE
DAILY(MON-FRI)
WEEKLY
PROGRAM REVIEW
SELECT KL CHOOSE
B
TO END PRESS EXIT
3
Press the PLAY/▲ button or the STO P/▼ button to select
a O NCE, DAILY, O R W EEKLY recording. Then, press
the F.FW D/B button.
Helpful Hints
● O NCE: The TV/VCR will record a TV program on any day you
choose, up to 12 months away.
● DAILY: The TV/VCR will record every day from Monday to
Friday – starting at the same time and recording the same channel
for the same length of time.
● W EEKLY: The TV/VCR will record the same channel on the
same day, at the same time, and for the same length of time
every week.
• With ShowGuard, you don’t have to
worry about losing your timer
recordings. If the power fails, timer
recordings will be restored when the
clock is reset. (The clock will reset
itself automatically if you are using
AUTO CLOCK. Details are on pages
14-17. If you are not using AUTO
CLOCK, reset the clock manually.
Details are on pages 12-13.) The
timer recording will not occur only if
it was scheduled to take place dur-
ing the power failure.
DAILY PROGRAM (MON-FRI)
PROGRAM -1 2 3 4 5 6 7 8-
Daily
Recording
(exam ple)
SELECT PROGRAM NUMBER
TO END PRESS EXIT
• You cannot set a timer recording if
DEFEAT RECORDING is ON.
Details are on page 36.
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer Recording (cont’d) 33
4
4-7
Use the Num ber buttons (1-8) to select a position in
which to store the tim er recording. Flashing numbers indi-
cate an open position (one in which a timer recording has not
been stored yet).
EJECT
POWER
NOTE: If you select a number that already has been used to store a
timer recording, PREVIOUSLY SET PROGRAM will appear on the screen
for a few seconds. Then information about the program in that position
will appear on the screen. If this happens, press the STATUS/EXIT but-
ton. Then use the Number buttons to select another position.
MENU
CLEAR
STATUS/EXIT
1
4
7
2
5
8
3
6
9
SLEEP/
ALT.CH
WAKE UP
5
0
Use the Num ber buttons to enter the channel of the TV
program you want to record.
● If you are recording from line input, press 0, 0. A/V IN will
appear on the screen.
REC
/OTR
PAUSE
/STILL
PLAY
REW
F.FWD
● If you are recording using a Cable Box, enter the Cable Box
output channel (03 or 04). Be sure to select the channel of the
TV program at the Cable Box and leave the Cable Box on for
the timer recording.
STOP
MUTE
CH.
VOL.
ONE TIME PROGRAM
SPEED
PROGRAM
1
CHANNEL – – –
TRACKING MEMORY
TO CORRECT PRESS CLEAR
TO END PRESS EXIT
6
Press two Num ber buttons for the hour(s) you want the
recording to begin. Press two Num ber buttons for the
m inute(s) you want the recording to begin. Press 1 for
AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.
ONE TIME PROGRAM
PROGRAM
1
CHANNEL 10
TIME ON
– – : – –
TO CORRECT PRESS CLEAR
TO END PRESS EXIT
Helpful Hints
7
• If you enter numbers that do not
match the TV/VCR’s clock or calen-
dar, the entry will be rejected and a
question mark will appear on the
screen.
Follow the instructions in step 6 to set the recording’s
stop tim e. (AM or PM will be set automatically.)
ONE TIME PROGRAM
PROGRAM
1
• To make corrections while you are
programming a timer recording,
press the CLEAR button until the
cursor is flashing on the item you
want to change. Then enter the cor-
rect information.
CHANNEL 10
TIME ON
09:30 PM
TIME OFF – – : – –
TO CORRECT PRESS CLEAR
TO END PRESS EXIT
Instructions continue on page 34.
Download from Www.Somanuals.com. All Manuals Search And Download.
34 Timer Recording (cont’d)
8
1011
Press the Num ber 1 button to record in SP speed or
press the Num ber 2 button to record in SLP speed. Details
about tape speed are on page 29. You cannot use the SPEED button
at this time.
EJECT
POWER
MENU
CLEAR
STATUS/EXIT
ONE TIME PROGRAM
PROGRAM
1
1
4
7
2
5
8
3
6
CHANNEL 10
TIME ON
TIME OFF 11:00 PM
REC SPEED SLP
SP=1 SLP=2
09:30 PM
8
9
9
SLEEP/
ALT.CH
WAKE UP
TO CORRECT PRESS CLEAR
TO END PRESS EXIT
0
REC
/OTR
PAUSE
/STILL
PLAY
REW
F.FWD
9
Press two Num ber buttons for the m onth and two
Num ber buttons for the day you want the program to
record. For example, for July 10, 2001, press 07, 10. The day of
the week and the year will appear automatically. (You cannot pro-
gram the TV/VCR to record more than one year in advance.)
STOP
MUTE
CH.
VOL.
SPEED
ONE TIME PROGRAM
PROGRAM
1
TRACKING MEMORY
CHANNEL
TIME ON
TIME OFF
REC SPEED
10
09:30 PM
11:00 PM
SLP
START DATE 07/10/2001
TUESDAY
Turn off the TV/VCR
for the recording.
Insert a tape in
the TV/VCR.
TO CORRECT PRESS CLEAR
TO END PRESS EXIT
10
Leave the Cable
Box/DBS on
(if applicable).
Press the STATUS/EXIT button. PROGRAM WAS COM-
PLETED PLEASE TURN OFF FOR TIMER RECORDING will
appear on the screen.
● If there is not a tape in the TV/VCR, PLEASE INSERT CAS-
SETTE also appears on the screen.
● If there is a tape without a record tab in the TV/VCR, PLEASE
REMOVE CASSETTE also appears on the screen. If this hap-
pens, insert a different tape.
Helpful Hints
• PROGRAM NOT COMPLETED /
CLASH may appear on the screen
when you finish setting a timer
recording. This means the timer
recording you just tried to program
overlaps with another timer recording.
The latest timer recording will not
occur.
● If PROGRAM NOT COMPLETED appears, start again at step 1.
11
Press the PO W ER button to turn off the TV/VCR power.
The Record light will flash slowly. If you forget to turn off the
TV/VCR, PLEASE TURN OFF FOR TIMER RECORDING appears
on the TV/VCR screen two minutes before a timer recording
should begin.
• To stop a timer recording that is in
progress, press the STOP/EJECT but-
ton on the TV/VCR once.
Please see page 54 for more
Helpful Hints.
Download from Www.Somanuals.com. All Manuals Search And Download.
Timer Recording (cont’d) 35
Checking or Clearing Tim er Recordings
5 2-4
1
W ith the TV/VCR on, press the MENU button.
EJECT
POWER
2
MENU
CLEAR
STATUS/EXIT
Press the PLAY/▲ button or the STO P/▼ button to select
VCR PRO GRAM, then press the F.FW D/B button.
1
1
4
7
2
5
8
3
6
3
9
SLEEP/
Press the PLAY/▲ button or the STO P/▼ button to select
PRO GRAM REVIEW , then press the F.FW D/B button.
The timer recording information for the program in the lowest
numbered position will appear on the screen. If no timer record-
ings are programmed, nothing will happen when you select PRO-
GRAM REVIEW and press the F.FWD/B button.
ALT.CH
WAKE UP
0
REC
/OTR
PAUSE
/STILL
PLAY
REW
F.FWD
STOP
MUTE
CH.
VOL.
4
Press the F.FW D/B button to display inform ation about the
next tim er recording. (If you do not press a button within 10 sec-
onds, information about the next timer recording will appear auto-
matically.) This will continue until all positions have been displayed.
Then, the menu will disappear. You can exit the Program Review at
any time by pressing the STATUS/EXIT button.
SPEED
TRACKING MEMORY
5
To cancel the tim er recording displayed, press the
CLEAR button. Either the display will disappear or information
about other timer recordings will appear. If you do not press any
other buttons, the display will disappear after all timer recordings
have been displayed.
6
Repeat steps 1-4 to m ake sure you cleared the correct
recording.
Helpful Hint
• With ShowGuard, you don’t have to
worry about losing your timer
recordings. If the power fails, timer
recordings will be restored when the
clock is reset. (The clock will reset
itself automatically if you are using
AUTO CLOCK. Details are on pages
14-17. If you are not using AUTO
CLOCK, reset the clock manually.
Details are on pages 12-13.) The
timer recording will not occur only if
it was scheduled to take place
during the power failure.
Download from Www.Somanuals.com. All Manuals Search And Download.
36 Defeat Recording
Follow the steps below to prevent accidental recording.
4 2-3
1
Press the MENU button.
EJECT
POWER
MENU
CLEAR
STATUS/EXIT
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
1
1
4
7
2
5
8
3
6
REMINDER
BRIGHTNESS
9
SLEEP/
ALT.CH
WAKE UP
0
2
REC
/OTR
PAUSE
/STILL
Press the PLAY/▲ button or the STO P/▼ button to select
VCR SETUP, then press the F.FW D/B button.
PLAY
REW
F.FWD
VCR SETUP
STOP
MUTE
> ONE TIME PLAY
REPEAT PLAY
ON-SCREEN MODE
DEFEAT RECORDING [OFF]
BLUE BACKGROUND [ON]
[ON]
CH.
VOL.
SELECT KL CHOOSE
B
TO END PRESS EXIT
SPEED
TRACKING MEMORY
3
Press the PLAY/▲ button or the STO P/▼ button to select
DEFEAT RECO RDING, then press the F.FW D/B button
so that O N appears beside DEFEAT RECO RDING.
VCR SETUP
ONE TIME PLAY
REPEAT PLAY
[ON]
ON-SCREEN MODE
> DEFEAT RECORDING [ON]
BLUE BACKGROUND [ON]
SELECT KL CHOOSE
B
TO END PRESS EXIT
Helpful Hints
4
Press the STATUS/EXIT button.
• If you set DEFEAT RECORDING to
ON after you program a timer
recording, the timer recording will not
occur.
• You can not program a timer
recording if DEFEAT RECORDING is
ON.
5
Now, REC DEFEATED will flash on the screen when you
press the REC(ord)/O TR button.
REC DEFEATED
• To set DEFEAT RECORDING to OFF,
repeat steps 1-2 above. At step 3,
press the PLAY/o button or the
STOP/p button to select DEFEAT
RECORDING, then press the
F.FWD/B button so that OFF
appears beside DEFEAT
RECORDING. Press the
STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeat Play 37
Follow the steps below to program the TV/VCR to play a tape
over and over.
4 2-3
1
EJECT
Press the MENU button.
POWER
MENU
CLEAR
STATUS/EXIT
1
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
1
4
7
2
5
8
3
6
REMINDER
BRIGHTNESS
9
SLEEP/
ALT.CH
WAKE UP
0
REC
/OTR
PAUSE
/STILL
2
PLAY
Press the PLAY/▲ button or the STO P/▼ button to select
VCR SETUP, then press the F.FW D/B button.
REW
F.FWD
STOP
MUTE
VCR SETUP
> ONE TIME PLAY
REPEAT PLAY
ON-SCREEN MODE
[ON]
CH.
VOL.
DEFEAT RECORDING [OFF]
BLUE BACKGROUND [ON]
SELECT KL CHOOSE
TO END PRESS EXIT
B
SPEED
TRACKING MEMORY
3
Press the PLAY/▲ button or the STO P/▼ button to select
REPEAT PLAY, then press the F.FW D/B button so that
O N appears beside REPEAT PLAY.
VCR SETUP
ONE TIME PLAY
> REPEAT PLAY
[ON]
ON-SCREEN MODE
DEFEAT RECORDING [OFF]
BLUE BACKGROUND [ON]
SELECT KL CHOOSE
B
TO END PRESS EXIT
4
Helpful Hints
Press the STATUS/EXIT button. Now, when a tape finishes
playing, the TV/VCR will rewind it and start playback again.
(TV programming will appear while the tape is rewinding.)
• The TV/VCR will stay in Repeat Play
mode until you set ONE TIME PLAY
to ON, even if you turn off the
TV/VCR. To set ONE TIME PLAY to
ON, follow steps 1-2 above. Then,
press the PLAY/o button or the
STOP/p button to select ONE TIME
PLAY. Press the F.FWD/B button so
that ON appears beside ONE TIME
PLAY. Then, press the STATUS/EXIT
button.
• The real-time counter memory will
not function during Repeat Play
mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
38 A-B Repeat Play
Follow the steps below to program the TV/VCR to play the mate-
rial between two specified points (A and B) on a tape over and
over again.
Insert a tape in the TV/VCR.
1
2
EJECT
POWER
1
MENU
CLEAR
STATUS/EXIT
Insert a tape in the TV/VCR.
1
4
7
2
5
8
3
6
2
Press the MENU button.
9
SLEEP/
ALT.CH
WAKE UP
0
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
REC
/OTR
PAUSE
/STILL
PLAY
REMINDER
BRIGHTNESS
REW
F.FWD
STOP
MUTE
CH.
VOL.
3
Press the PLAY/▲ button or the STO P/▼ button to select
VCR SETUP, then press the F.FW D/B button.
SPEED
VCR SETUP
TRACKING MEMORY
> ONE TIME PLAY
REPEAT PLAY
[ON]
ON-SCREEN MODE
DEFEAT RECORDING [OFF]
BLUE BACKGROUND [ON]
SELECT KL CHOOSE
B
TO END PRESS EXIT
4
Press the PLAY/▲ button or the STO P/▼ button to select
REPEAT PLAY.
VCR SETUP
3-5
ONE TIME PLAY
> REPEAT PLAY
ON-SCREEN MODE
DEFEAT RECORDING [OFF]
BLUE BACKGROUND [ON]
[ON]
SELECT KL CHOOSE
B
TO END PRESS EXIT
Helpful Hints
• To cancel A-B Repeat Play, set ONE
TIME PLAY to ON. To set ONE
TIME PLAY to ON, follow steps 2-3
above. Then, press the PLAY/o but-
ton or the STOP/p button to select
ONE TIME PLAY. Press the
5
Press the F.FW D/B button repeatedly so that A-B
appears beside REPEAT PLAY.
VCR SETUP
ONE TIME PLAY
> REPEAT PLAY
[A-B]
F.FWD/B button so that ON
appears beside ONE TIME PLAY.
Then, press the STATUS/EXIT
button.
ON-SCREEN MODE
DEFEAT RECORDING [OFF]
BLUE BACKGROUND [ON]
SELECT KL CHOOSE
TO END PRESS EXIT
B
• The end position (B) must be later on
the tape than the start position (A).
Download from Www.Somanuals.com. All Manuals Search And Download.
A-B Repeat Play (cont’d) 39
6
6 7-8
Press the STATUS/EXIT button to rem ove the m enu. A-B
REPEAT will appear on the screen. Beneath it, the letter A will
flash beside the real-time counter.
EJECT
POWER
MENU
CLEAR
STATUS/EXIT
1
4
7
2
5
8
3
6
A-B REPEAT
0:12:34
A
9
SLEEP/
ALT.CH
WAKE UP
0
7
REC
PAUSE
/STILL
Play, fast forward, or rewind the tape to the position at
which you want to begin playback. Stop the tape, then
press the MEMO RY button to set the start position (A).
The flashing A will become a flashing B.
/OTR
PLAY
REW
F.FWD
STOP
MUTE
CH.
VOL.
SPEED
A-B REPEAT
B
0:00:00
TRACKING MEMORY
8
Play or fast forward the tape to the position at which you
want playback to end. Stop the tape, then press the
MEMO RY button to set the end position (B).
● The length of time between the start position (A) and the end
position (B) must be at least three minutes.
9
The TV/VCR will immediately rewind the tape to the start posi-
tion (A) and repeat playback to the end position (B) over and
over.
Helpful Hints
(TV programming will appear while the tape is rewinding.)
• The counter cannot be memorized
or reset when you are using this
feature.
• A-B Repeat Play will be cancelled if
you eject the tape or press the
REC(ord)/OTR button.
• A-B REPEAT will not appear on the
screen at step 6 if a tape is not in
the TV/VCR. NO CASSETTE will
flash on the screen briefly.
• You cannot rewind or fast forward
beyond points A or B when you are
using this feature.
• A-B Repeat Play will be retained if
you turn off the TV/VCR power.
Download from Www.Somanuals.com. All Manuals Search And Download.
40 Real-Time Counter Memory
Follow the steps below to reset the real-time counter to zero at a
tape location you want to refer to later.
3
1
Play, fast forward, or rewind a tape to the location that
you would like to refer to later. Stop the tape.
EJECT
MENU
POWER
CLEAR
STATUS/EXIT
2
1
4
7
2
5
8
3
6
2
Press the STATUS/EXIT button. The real-time counter will
appear on the screen.
9
01:08 PM
CH10
STOP
SLEEP/
ALT.CH
WAKE UP
0
REC
/OTR
PAUSE
/STILL
PLAY
SLP
1 : 23 : 45
REW
F.FWD
STOP
MUTE
3
CH.
VOL.
W hile the counter rem ains on the screen, press the
CLEAR button to reset the real-tim e counter to zero.
SPEED
TRACKING MEMORY
0 : 00 : 00
4
4
W hile the counter rem ains on the screen, press the MEM-
O RY button so that M appears on the screen. To erase a
real-time counter memory, press the MEMORY button so that the
M disappears from the screen.
1,5
M 0 : 00 : 00
5
To go to the tape location where you set the real-tim e
counter to zero, press the REW (ind)/s button or the
F.FW D/B button when playback is stopped. W hen the
tape reaches the point at which you set the counter to
zero, the tape will stop. Press the PLAY/o button to
watch the tape.
Helpful Hints
• The real-time counter memory will
not function during Repeat Play
mode. Details are on page 37.
• You may only set one real-time
counter memory at a time. If you
set the real-time counter to zero at
a second location, the previous real-
time counter to zero setting will be
lost.
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback Options 41
Forward and Reverse Searching (SP/LP/SLP)
1
During tape playback, press and release the F.FWD/B button or
the REW(ind)/{ button. A fast forward or reverse picture search
will begin.
EJECT
POWER
MENU
CLEAR
STATUS/EXIT
1
4
7
2
5
8
3
6
2
9
SLEEP/
ALT.CH
WAKE UP
To return to normal playback, press the PLAY/▲ button.
0
REC
/OTR
PAUSE
/STILL
Super High Speed Searching (LP/SLP)
PLAY
REW
F.FWD
1
STOP
MUTE
During tape playback, press the F.FWD/B button or the
REW(ind)/{ button, then press again. The TV/VCR will now
search in super high speed.
CH.
VOL.
Press the F.FWD/B button or the REW(ind)/{ button repeatedly
to switch between regular and super high speed searching.
SPEED
TRACKING MEMORY
2
To return to normal playback, press the PLAY/▲ button.
Viewing a Still Picture
1
During tape playback, press the PAUSE/STILL button. A still pic-
ture will appear on the screen. The noise lines will move each
time you press the PAUSE/STILL button.
Helpful Hints
• Still mode will automatically switch to
Stop mode after five minutes to pro-
tect the TV/VCR and the tape from
damage.
• SP/LP/SLP means this feature will
work with tapes recorded in Standard
Play, Long Play, or Super Long Play.
For details about tape speed, see
page 29.
2
To release the still picture and return to normal playback, press
the PLAY/▲ button.
• LP/SLP means this feature will work
with tapes recorded in Long Play and
Super Long Play. For details on tape
speed, see page 29.
• During forward and reverse search-
ing, horizontal noise bars will appear
on the TV/VCR screen.
• Tapes recorded in SLP speed will
have the clearest picture during for-
ward and reverse searching and Still
mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
42 SmartLock
SmartLock enables parents to prevent their children from watch-
ing inappropriate material on TV.
SmartLock reads the ratings for programming (except for news
and sports programs, unedited movies on premium cable channels,
and Emergency Broadcast System signals), then denies access to
programming if the program’s rating meets or exceeds the limita-
tions you select. The ratings are defined on page 45.
To block ratings, follow the steps below.
2,4
EJECT
MENU
POWER
STATUS/EXIT
CLEAR
1
3
1
4
7
2
5
8
3
6
1
Press the MENU button.
9
SLEEP/
ALT.CH
WAKE UP
0
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
REC
/OTR
PAUSE
/STILL
PLAY
REMINDER
REW
F.FWD
BRIGHTNESS
STOP
MUTE
CH.
VOL.
2
Press the PLAY/▲ button or the STO P/▼ button to select
SMARTLO CK. Then, press the F.FW D/B button.
SMARTLOCK
_ _ _ _
Enter Your Access Code
3
Helpful Hints
Use the Num ber buttons to enter your access code.
The default code is 0711. If you have not set up your personal
access code, you should use 0711. (To set up your personal
access code, see page 44.)
• If the “Incorrect Access Code...” mes-
sage appears after step 3, enter the
correct access code.
• Programming may be rated by the
Motion Picture Association of America
(MPAA) or according to the Television
Parental Guidelines. In order to block
any inappropriate programming, set
your limits in both places (Movie
Ratings and Parental Guidelines).
You will complete steps 1-7 twice,
choosing Movie Ratings at step 5 the
first time, then choosing Parental
Guidelines at step 5 the second time.
• You can not view tape playback if the
rating of the tape is blocked.
• If you enter the access code once,
you may change channels without
seeing the “CHANNEL XX
BLOCKED” message again. If you
turn off the TV/VCR power, you will
be asked for the access code again
when you tune to a blocked channel.
The SMARTLOCK menu will appear.
SMARTLOCK
X X X -
Enter Your Access Code
4
Press the PLAY/▲ button or the STO P/▼ button to select
BLO CK. Then, press the F.FW D/B button.
SMARTLOCK
> BLOCK
CHANGE CODE
SELECT KL CHOOSE
B
TO END PRESS EXIT
Download from Www.Somanuals.com. All Manuals Search And Download.
SmartLock (cont’d) 43
5
7 5-6
Press the PLAY/▲ button or the STO P/▼ button to select
Movie Ratings or Parental Guidelines. Then, press the
F.FW D/B button.
EJECT
BLOCK
POWER
> Movie Ratings
MENU
CLEAR
STATUS/EXIT
Parental Guidelines
1
4
7
2
5
8
3
6
SELECT KL CHOOSE
TO END PRESS EXIT
B
9
SLEEP/
ALT.CH
WAKE UP
0
6
REC
/OTR
PAUSE
/STILL
Press the PLAY/▲ button or the STO P/▼ button to select
the rating you want to block. Then, press the F.FW D/B
button so that O N appears beside the rating.
PLAY
REW
F.FWD
For example, if you set PG to ON, you may not view PG pro-
gramming because the block is on. Programs with a PG or higher
rating will be blocked. A “CHANNEL XX BLOCKED...” message
will appear when someone tries to access such programming.
STOP
MUTE
CH.
VOL.
PARENTAL GUIDELINES
MOVIE RATINGS
> TV-Y
TV-Y7
- - - - - - - - - - - - - - - -
TV-G
TV-PG
TV-14
TV-MA
[OFF]
>
SPEED
>G
PG
PG-13
R
NC-17
X
[OFF]
[OFF]
[OFF]
[OFF]
[OFF]
[OFF]
TRACKING MEMORY
[OFF]
>
>
>
SELECT KL CHOOSE
B
SELECT KL CHOOSE
B
TO END PRESS EXIT
TO END PRESS EXIT
● More specific sub-ratings are available for TV-Y7, TV-PG, TV-14,
and TV-MA. (See example below.) When you press the
F.FWD/B button to turn on TV-Y7, TV-PG, TV-14 or TV-MA,
additional sub-ratings will appear.
If you select the rating category, such as TV-PG, and turn it on
or off, the specific sub-ratings, such as V for Violence, will turn
on or off automatically. You can always turn specific sub-ratings
on or off by selecting them individually. However, you may only
set a sub-rating to ON if the rating category is set to ON.
● Ratings are defined on page 45.
Helpful Hints
• If the “CHANNEL XX BLOCKED...”
or “PLAYBACK BLOCKED...” mes-
sage appears and you want to view
this programming, enter your access
code. The channel will remain
blocked until you enter the correct
code. If you do not know the code,
you will have to select another chan-
nel or press the STOP/p button.
• Ratings will remain blocked even
after a power failure.
Exam ple
of specific
sub-ratings
TV-PG
> TV-PG
[OFF]
D
L
S
[OFF]
[OFF]
[OFF]
[OFF]
V
SELECT KL CHOOSE
B
TO END PRESS EXIT
• You cannot access the menu when
the “CHANNEL XX BLOCKED...” or
“PLAYBACK BLOCKED...” message
appears.
7
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
44 SmartLock (cont’d)
To change the access code, follow these steps.
6
2,4
1
Press the MENU button.
>
SMARTLOCK
REVIEW
PRESS
B
EJECT
POWER
EXIT
PRIM. SETUP
VCR PROGRAM
VCR SETUP
MENU
CLEAR
STATUS/EXIT
1
5
3
1
4
7
2
5
8
3
6
2
9
Press the PLAY/▲ button or the STO P/▼ button to select
SMARTLO CK. Then, press the F.FW D/B button.
SMARTLOCK
SLEEP/
ALT.CH
WAKE UP
0
REC
/OTR
PAUSE
/STILL
PLAY
_ _ _ _
REW
F.FWD
Enter Your Access Code
STOP
MUTE
CH.
VOL.
3
Use the Num ber buttons to enter your old access code.
The default code is 0711. If you have never set up your personal
access code, use 0711 now.
SPEED
After you enter the code, the SMARTLOCK menu will appear.
TRACKING MEMORY
SMARTLOCK
X X X -
Enter Your Access Code
4
Press the PLAY/▲ button or the STO P/▼ button to select
CHANGE CO DE. Then, press the F.FW D/B button.
SMARTLOCK
Helpful Hints
BLOCK
> CHANGE CODE
• To protect the privacy of the access
code, an X will appear on the screen
instead of the number you enter.
• If a “Wrong Code...” message
appears on the screen after you com-
plete step 5, you entered the wrong
numbers in the Confirm Code space.
Repeat the steps on this page.
• You cannot use the default code after
you set up your personal access code.
• If a power failure occurs, the default
code, 0711, will be the active access
code again.
SELECT KL CHOOSE
TO END PRESS EXIT
B
5
Use the Num ber buttons to enter your desired access code
in the New Code space. Then, enter the sam e code in the
Confirm Code space.
Your new access code should be recorded. You will return to the
SMARTLOCK menu.
_ _ _ _
New Code
• If you connect the power cord to an
AC outlet that is controlled by a wall
switch, your personal access code will
be erased every time you turn off the
power at the wall switch. The default
code will be the active code again.
Confirm Code
_ _ _ _
6
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
SmartLock (cont’d) 45
To check the SmartLock settings and see which ratings you have
blocked, follow these steps.
1
Press the MENU button.
EJECT
POWER
>
REVIEW
EXIT
PRESS
B
MENU
CLEAR
STATUS/EXIT
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
1
1
4
7
2
5
8
3
6
3
2
9
SLEEP/
ALT.CH
WAKE UP
2
0
Press the PLAY/▲ button or the STO P/▼ button to select
REVIEW . Then, press the F.FW D/B button so that the
Sm artLock settings appear.
REC
/OTR
PAUSE
/STILL
PLAY
REW
F.FWD
Ratings that are blocked will appear on the screen.
An “X” will appear if a specific sub-rating is blocked, such as V for
Violence in the TV-14 category.
STOP
MUTE
CH.
VOL.
BLOCKED RATINGS
Movie Ratings
G
PG-13
NC-17
Parental Guidelines
TV-Y7
- - - - - - - - - - - - - - - - - - - -
TV-G
SPEED
D
L
S
x
x
x
V
x
x
x
TV-PG
TV-14
TV-MA
TRACKING MEMORY
x
–
x
x
3
Press the STATUS/EXIT button.
RATING EXPLANATIO NS
For Movie Ratings
• G - General Audience
• PG - Parental Guidance suggested.
• PG-13 - Unsuitable for children under 13
• R - Restricted; under 17 requires accompanying parent or adult
guardian
• NC-17 - No one under 17 admitted
• X - Mature audience only
For Parental Guidelines
• V - Violence
• S - Sexual situations
• L - Language
• D - Inappropriate dialogue
• FV - Fantasy Violence may frighten children under seven; TV-Y7
category only. Some cartoons may have this rating.
• TV-Y - Appropriate for all children
• TV-Y7 - Appropriate for children seven and older
• TV-G - General Audience
• TV-PG - Parental Guidance suggested.
• TV-14 - Unsuitable for children under 14
• TV-MA - Mature audience only
Download from Www.Somanuals.com. All Manuals Search And Download.
46 Blue Background
If you want the TV screen to be solid blue when a weak signal is
received, set BLUE BACKGROUND to ON. The screen will be
blue and the sound will be muted. Or, if you want to receive the
weak signal, set BLUE BACKGROUND to OFF. When you select
a channel that is receiving a weak signal, you will see and hear the
static in the TV programming.
4
2-3
EJECT
POWER
To set BLUE BACKGROUND to ON or OFF, follow the steps
below.
MENU
CLEAR
STATUS/EXIT
1
1
4
7
2
5
8
3
6
1
Press the MENU button.
9
SLEEP/
ALT.CH
WAKE UP
0
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
REC
/OTR
PAUSE
/STILL
PLAY
REMINDER
REW
F.FWD
BRIGHTNESS
STOP
MUTE
CH.
VOL.
2
Press the PLAY/o button or the STO P/p button to select
VCR SETUP, then press the F.FW D/B button.
SPEED
VCR SETUP
TRACKING MEMORY
> ONE TIME PLAY
REPEAT PLAY
[ON]
ON-SCREEN MODE
DEFEAT RECORDING [OFF]
BLUE BACKGROUND [ON]
SELECT KL CHOOSE
B
TO END PRESS EXIT
3
Press the PLAY/o button or the STO P/p button to select
BLUE BACKGRO UND. Then, press the F.FW D/B button
repeatedly so that O FF (or O N) appears beside BLUE BACK-
GRO UND.
VCR SETUP
ONE TIME PLAY
REPEAT PLAY
[ON]
ON-SCREEN MODE
DEFEAT RECORDING [OFF]
> BLUE BACKGROUND [ON]
SELECT KL CHOOSE
B
TO END PRESS EXIT
4
Press the STATUS/EXIT button.
Helpful Hint
• A blue screen may appear briefly
between channel changes if BLUE
BACKGROUND is ON. To avoid
having the brief blue screen, set
BLUE BACKGROUND to OFF.
Download from Www.Somanuals.com. All Manuals Search And Download.
Sleep Timer 47
Use the sleep timer to program the TV/VCR to shut off in a cer-
tain amount of time.
1
Press the SLEEP/W AKE UP button.
EJECT
MENU
TO ADJUST PRESS s /
B
POWER
CLEAR
STATUS/EXIT
–TIMER–
>
SLEEP
WAKE UP
ON-TIME
OFF
1
4
7
2
5
8
3
6
3
2
9
SLEEP/
ALT.CH
WAKE UP
0
2
1
REC
/OTR
PAUSE
/STILL
o
p
Press the PLAY/ button or the STO P/ button to select
SLEEP. Then press the REW (ind)/s button or the
F.FW D/B button to select 30 MIN(utes), 60 MIN(utes),
90 MIN(utes), or 120 MIN(utes). (You can not set the sleep
timer during a recording.)
PLAY
REW
F.FWD
STOP
MUTE
CH.
VOL.
TO ADJUST PRESS s /
B
–TIMER–
>
SLEEP
WAKE UP
ON-TIME
30 MIN
SPEED
TRACKING MEMORY
3
Press the STATUS/EXIT button. The TV/VCR will shut itself
off after the specified amount of time.
One minute before the TV/VCR shuts itself off, the seconds will
count down on the screen.
GOOD NIGHT appears on the TV/VCR screen 10 seconds
before the TV/VCR shuts itself off.
Helpful Hints
• To cancel the sleep timer, press the
SLEEP/WAKE UP button. Press the
PLAY/o button or the STOP/p but-
ton to select SLEEP, then press the
s
REW(ind)/ button or the
B
F.FWD/ button to select OFF. Press
the STATUS/EXIT button.
• To see how much time remains
before the TV/VCR shuts itself off,
press the SLEEP/WAKE UP button
once. If necessary, press the PLAY/o
button or the STOP/p button to
select SLEEP. The remaining time will
appear beside SLEEP. To remove the
display, press the STATUS/EXIT but-
ton.
• If you start a recording after you set
the Sleep Timer, the Sleep Timer will
be cancelled.
Download from Www.Somanuals.com. All Manuals Search And Download.
48 Wake Up Timer
The Wake Up Timer turns on the TV/VCR automatically at a speci-
fied time within the next 24 hours. You may set the TV/VCR to turn
on at a TV channel (the channel at which the TV/VCR was set last)
or with VCR playback. To set the Wake Up Timer, follow the steps
below. Before you begin:
● Set the clock. If the clock is not set, CLOCK MUST BE SET will
appear on the screen after you select WAKE UP at step 2. Then
the SET CLOCK menu will appear. Details are on pages 12-17.
● Put a tape in the TV/VCR if you want the TV/VCR to start tape
playback at the specified time.
5
2-3
EJECT
MENU
POWER
CLEAR
STATUS/EXIT
1
4
7
2
5
8
3
6
4
1
● Make sure no timer recordings are set for the time at which you
want the TV/VCR power to come on.
9
SLEEP/
ALT.CH
WAKE UP
0
1
Press the SLEEP/W AKE UP button.
REC
/OTR
PAUSE
/STILL
PLAY
TO ADJUST PRESS s /
B
–TIMER–
REW
F.FWD
>
SLEEP
WAKE UP
ON-TIME
OFF
STOP
MUTE
CH.
VOL.
2
SPEED
Press the PLAY/o button or the STOP/p button to select
s button or the
TRACKING MEMORY
W AKE UP. Then, press the REW (ind)/
F.FW D/B button to select TV ON or VCR ON.
TO ADJUST PRESS s /
–TIMER–
B
SLEEP
WAKE UP
ON-TIME
>
TV ON
3
Press the PLAY/o button or the STOP/p button to select
s
ON-TIME. Then, press the REW (ind)/ button or the
B
F.FW D/ button to select your desired wake up tim e. Each
s
B
press of the REW(ind)/ button or the F.FWD/ button will
increase (or decrease) the time by 10 minutes.
TO ADJUST PRESS s /
B
–TIMER–
SLEEP
WAKE UP
ON-TIME
12:00 AM
>
Helpful Hint
4
• To cancel the Wake Up Timer, press
the SLEEP/WAKE UP button. Press
the PLAY/o button or the STOP/p
button to select WAKE UP. Then,
Press the STATUS/EXIT button.
5
s
press the REW(ind)/ button or the
B
F.FWD/ button to select OFF. Press
Press the POW ER button to turn off the TV/VCR. The
TV/VCR will turn itself on at the specified tim e.
the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
Volume Bar 49
Usually, the volume bar appears when you press the VOL(ume)
o/p buttons. If you do not need it, set the VOLUME BAR to
OFF. For example, when you watch a program that is being broad-
cast with closed captions, you may choose to set the VOLUME
BAR to OFF so the captions can remain on the screen. The cap-
tions will remain on the screen even when you press the
VOL(ume) o/p buttons or the MUTE button.
4 2-3
EJECT
POWER
MENU
CLEAR
STATUS/EXIT
1
1
4
7
2
5
8
3
6
1
Press the MENU button.
9
SLEEP/
ALT.CH
WAKE UP
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
0
REC
/OTR
PAUSE
/STILL
REMINDER
PLAY
BRIGHTNESS
REW
F.FWD
STOP
MUTE
2
CH.
VOL.
Press the PLAY/▲ button or the STO P/▼ button to select
PRIM. SETUP. Then, press the F.FW D/B button.
PRIMARY SETUP
> SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
SPEED
VOLUME BAR
SET CLOCK
[OFF]
TRACKING MEMORY
SELECT KL CHOOSE
B
TO END PRESS EXIT
3
Press the PLAY/▲ button or the STO P/▼ button to select
VO LUME BAR, then press the F.FW D/B button. Each
press of the F.FWD/B button will turn the VOLUME BAR ON or
OFF.
PRIMARY SETUP
SELECT LANGUAGE
AUTO PROGRAMMING
CH MEMORY REVIEW
> VOLUME BAR
SET CLOCK
[ON]
SELECT KL CHOOSE
B
TO END PRESS EXIT
4
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
50 Closed Caption
When you watch a program that has closed captions, you can
access on-screen boxes containing the program’s dialogue (for
example, what a character is saying), dialogue in a foreign lan-
guage, or information (such as a channel guide, schedule, or
announcements). Follow the steps below to select closed cap-
tions.
Not all TV programs and commercials have closed captions.
Similarly, all types of closed captions (second language, half-screen
text, etc.) are not always broadcast. If closed captioning is not
broadcast, you cannot receive it. This does not indicate a prob-
lem with the TV/VCR. Refer to your area’s TV program listings
for shows with closed captions.
2-3
EJECT
MENU
POWER
STATUS/EXIT
CLEAR
1
1
4
7
2
5
8
3
6
9
SLEEP/
ALT.CH
WAKE UP
0
1
REC
/OTR
PAUSE
/STILL
PLAY
Press the MENU button.
REW
F.FWD
STOP
MUTE
PRESS
B
>
PRIM. SETUP
VCR PROGRAM
VCR SETUP
CAPTION
CH.
VOL.
REMINDER
BRIGHTNESS
SPEED
2
TRACKING MEMORY
Press the PLAY/▲ button or the STO P/▼ button to select
CAPTIO N.
TO ADJUST PRESS { /
B
OFF
>
CAPTION
REMINDER
BRIGHTNESS
PICTURE
COLOR
TINT
3
Press the REW (ind)/{ button or the F.FW D/B button to
select your desired closed caption m ode.
The selected closed caption mode will appear beside CAPTION
on the screen.
● CAPTION1 displays standard closed captions (what a character
is saying).
● CAPTION2 displays foreign language closed captions (foreign
language words showing what a character is saying).
● TEXT1 and TEXT2 display half-screen text (such as a channel
guide, schedule, or announcement).
● OFF turns off closed captions. Captions will not appear on the
screen.
TO ADJUST PRESS { /
B
Exam ple:
CAPTIO N1
Menu
CAPTION1
>
CAPTION
REMINDER
BRIGHTNESS
PICTURE
COLOR
Screen
TINT
Download from Www.Somanuals.com. All Manuals Search And Download.
Closed Caption (cont’d) 51
4
Press the STATUS/EXIT button. The type of closed captions
you selected at step 3 will appear on the screen.
EJECT
POWER
MENU
CLEAR
STATUS/EXIT
4
1
4
7
2
5
8
3
6
9
SLEEP/
ALT.CH
WAKE UP
0
REC
/OTR
PAUSE
/STILL
PLAY
HELLO
REW
F.FWD
Standard Closed Captions
STOP
MUTE
CH.
VOL.
SPEED
WORLD WEEATHER
5 C
8 C
7 C
23:00
20:00
4:00
CLOUD
RAIN
CLOUD
NYL
LOS
LONDON
TRACKING MEMORY
Half-screen text
Helpful Hints
• You cannot view closed captions dur-
ing recording or tape playback if
COUNTER ONLY is ON. Details are
on page 26.
• Abbreviations, symbols, and other
grammatical shortcuts are often used
in order to keep pace with the on-
screen action. This does not indicate
a problem with the TV/VCR.
• To cancel closed captions, follow
steps 1-2 on page 50. At step 3,
press the REW(ind)/{ button or the
F.FWD/B button to select OFF.
Press the STATUS/EXIT button.
• When you change channels, the
closed captions may be delayed for a
few seconds.
• When you adjust the volume or mute
the volume, closed captions may be
delayed for a few seconds. Details
are on page 49.
Download from Www.Somanuals.com. All Manuals Search And Download.
52 Automatic Operation Features
The following playback features will always operate.
Autom atic Playback
When you put a tape in the TV/VCR, the power will come on
automatically. If the tape’s record tab is missing, playback will
begin. If a timer recording is set, the power will not come on
automatically when you insert a tape with the record tab intact. If
a timer recording is set and the TV/VCR power is off, the
TV/VCR will eject the tape if the record tab is missing.
Autom atic Rewind, Eject, O ff
When you play, fast forward, or record a tape to its end, the
TV/VCR will rewind the tape, stop, turn itself off, and eject the
tape. If a real-time counter memory is set, the TV/VCR may only
rewind the tape to the point at which the real-time counter is set
to zero. The TV/VCR will not turn itself off or eject the tape.
Mem ory Rewind, Power O ff
When you press the POWER button while the TV/VCR is rewind-
ing a tape, REW → POWER OFF will appear on the screen. The
TV/VCR will turn itself off when the tape has finished rewinding.
If a real-time counter memory is set, the TV/VCR may only
rewind the tape to the point at which the counter was set to
zero, then turn itself off.
Tape Eject
A tape can be ejected with the TV/VCR power on or off (but the
TV/VCR must be plugged in). If a timer recording is programmed,
a tape can not be ejected when the power is off. Turn on the
TV/VCR power, then eject the tape. Be sure to insert a tape and
turn off the TV/VCR power for the timer recording.
Autom atic Tracking Adjustm ent
The TV/VCR automatically adjusts the tracking to give you the
best possible picture quality. With some recordings, however,
you may get a better picture using the manual tracking controls
(see below).
Manual Tracking
To adjust the tracking manually, press the CHANNEL o/p but-
tons on the TV/VCR or the TRACKING o/p buttons on the
remote control during playback.
Tracking returns to Automatic Tracking Adjustment when a tape
is inserted or when the STOP/p button is pressed.
Before
Tracking
Adjustment
After
Tracking
Adjustment
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary 53
AUDIO In Jack: jack on the front of the TV/VCR which is used
to record audio from another source.
Autom atic Channel Setup: process in which the TV/VCR
memorizes all available channels. Then, when you push the
CH(annel) o/p buttons, you only scan through channels you
receive.
Bands: settings that allow you to tune channels.
• Antenna – VHF (very high frequency; channels
2-13) and UHF (ultra high frequency; channels
14-69).
• Cable – all standard channels can be received without a Cable
Box.
Brightness: adjusting increases or decreases the brightness of
the color on the screen.
Color: adjusting pales or brightens the TV/VCR color.
Dubbing: copying a tape using a VCR.
HQ : high quality; a feature in the TV/VCR circuitry which pro-
vides enhanced picture detail.
Line Input: The channel to which you set your TV/VCR during
dubbing. The line input channel is always channel 00 (A/V IN).
Mode: a TV/VCR operation.
O TR: One-Touch Recording; a timed recording that starts
immediately and records for 30 minutes to eight hours, whichev-
er you specify.
Picture: adjusting increases or decreases the contrast of the pic-
ture on the screen.
Sharpness: adjusting softens or clarifies the picture on the screen.
Tape Speeds: how fast the tape travels during playback or
recording.
• SP (standard play) – fastest tape speed (recording time for a
T120 tape is approximately two hours); best picture quality.
• LP (long play) – average tape speed; playback only.
• SLP (super long play) – slowest tape speed (recording time for
a T120 tape is approximately six hours).
Tint: adjusting changes the tints of the picture on the TV/VCR
from purple to green.
VIDEO In Jack: jack on the front of the TV/VCR which is used
to record video from another source.
Download from Www.Somanuals.com. All Manuals Search And Download.
54 Helpful Hints
If you are having problems with your product, check this list of problems and possible solutions before
requesting service. You may be able to solve the problem yourself.
If you need to call a customer service representative, please know the model number and serial number of
your product before you call. This information is on the back of the product. Also, please take a moment to
identify the problem you are having, and be prepared to explain this to the representative. If the representa-
tive will need to help you with operations, please stay near the product. Our representatives will be happy to
assist you.
Location
For safe operation and satisfactory performance of your TV/VCR, remember the following:
• Shield it from direct sunlight and keep it away from sources of intense heat.
• Avoid dusty or humid places.
• Avoid places with insufficient ventilation. Do not block the ventilation openings at the top and bottom of
the TV/VCR. Do not place the TV/VCR on a carpet, as this will block the ventilation openings.
• Avoid locations subject to strong vibrations.
• Do not place the TV/VCR near strong magnetic fields.
• Do not move the TV/VCR from a cold place to a hot place, or vice versa.
Electrical Shock and Fire Hazards
• Do not handle the power cord with wet hands.
• Do not pull the power cord when disconnecting the TV/VCR from the AC (alternating current) wall out-
let. Grasp it by the plug.
• If you spill water on the TV/VCR, unplug the power cord immediately and take the TV/VCR to an autho-
rized service center.
• Do not put your fingers or objects into the TV/VCR cassette compartment.
• Do not place anything on top of the TV/VCR.
Dew W arning (Moisture Condensation)
• Moisture may condense inside the unit when you move it from a cold place to a warm place, after heating
a cold room, or when the humidity is high. There is no warning that moisture is in your TV/VCR. Playing a
tape in a TV/VCR in which moisture has accumulated could damage the tape and the TV/VCR. If you sus-
pect moisture inside the TV/VCR, keep the TV/VCR power on (but do not play a tape) for at least two
hours. This will allow the TV/VCR to dry.
TV/VCR will not perform a tim er recording.
• Set the recording start and stop times correctly. Details are on pages 32-35. Midnight is 12 a.m. Noon is 12
p.m.
• Make sure the TV/VCR power is off.
• Set the clock. Details are on pages 12-17.
• Put a tape in the TV/VCR. The tape must have a record tab.
• With ShowGuard, you don’t have to worry about losing your timer recordings. If the power fails, timer
recordings will be restored when the clock is reset. (The clock will reset itself automatically if you are
using AUTO CLOCK. Details are on pages 14-17. If you are not using AUTO CLOCK, reset the clock
manually. Details are on pages 12-13.) The timer recording will not occur only if it was scheduled to take
place during the power failure.
• Make sure DEFEAT RECORDING is set to OFF. Details are on page 36.
TV/VCR will not record.
• Make sure the tape has a record tab. Details are on page five.
• Make sure DEFEAT RECORDING is OFF. Details are on page 36.
• Plug the power cord into an active AC outlet. Details are on page seven.
• Check your hookups. Details are on pages six-seven.
• Set up the channels. Details are on page 10.
Channel reception is poor.
• Check connections, then set up the channels again. Details are on page 10.
Download from Www.Somanuals.com. All Manuals Search And Download.
Helpful Hints (cont’d) 55
The rem ote control is not available, or the rem ote control will not access the m enu.
• Use the buttons on the front of the TV/VCR to access the menu. You can not enter numbers (for example,
to program a timer recording) using the front panel buttons. Details are on page 20.
TV/VCR has no power.
• Connect the power plug to an AC (alternating current) outlet completely.
TV/VCR power shuts off after 15 m inutes.
• To save energy, the TV/VCR will shut itself off after 15 minutes when it is on a channel that is not receiving
a broadcast signal (for example, a station that has gone off the air for the night). This is normal.
TV/VCR does not have a picture.
• Adjust the antenna. Details are on page six.
• Adjust the TV/VCR picture controls. Details are on pages 24-25.
• Select an active channel.
TV/VCR has poor sound or no sound.
• Adjust the volume.
• Press the MUTE button to restore the volume.
Tape playback is poor or tape is destroyed.
• Adjust the tracking. Details are on page 52.
• If moisture has accumulated in your TV/VCR, keep the power on for at least two hours, but do not try to
play a tape. Details are on page 54.
TV/VCR does not display closed captions.
• Make sure COUNTER ONLY is OFF. Details are on page 26.
• Make sure closed captioning is available for the program. Refer to the TV listings in your local newspaper.
Rem ote control does not operate TV/VCR.
• Aim the remote control directly at the TV/VCR’s remote sensor. Details are on pages five and 20.
• Remove all obstacles between the remote control and the TV/VCR.
• Inspect and replace the batteries in the remote control. Details are on page five.
Num ber buttons will not select channels above 69.
• Enter channel numbers as a two-digit number. If you want to select channels 100 and above, enter channel
numbers as a three-digit number. Details are on page 22.
• If you are using an antenna, only channels 2-69 will be available. Details are on pages 10-11.
You can not insert a tape into the TV/VCR.
• Insert the tape window side up, with the record tab facing you.
• Make sure a tape isn’t already in the TV/VCR by pressing the STOP/EJECT button on the TV/VCR.
• Gently push on the center of the tape. Never force a tape into the TV/VCR.
• If you have set a timer recording and the TV/VCR power is off, the TV/VCR will eject the tape if the record
tab is missing.
You can not rem ove the tape from the TV/VCR.
• Make sure the power plug is completely connected to an AC (alternating current) outlet.
• If a timer recording is programmed, turn on the TV/VCR power, then eject the tape. Be sure to insert a
tape and turn off the TV/VCR power for the timer recording.
TV/VCR ejects the tape when you try to start a recording.
• Make sure the tape has a record tab. Details are on page five.
The cylinder rotates when tape playback is stopped.
• To enable the quick play mechanism, the cylinder will rotate for about five minutes. This is normal. The
quick play mechanism switches the tape mechanism from Stop to Play in just one second.
Download from Www.Somanuals.com. All Manuals Search And Download.
56 Specifications
General
CRT: 13-inch in line gun (CCC130 and CCC132)
19-inch in line gun (CCC190 and CCC192)
Television system: NTSC-M
Closed caption system: Section 15.119, FCC
(Federal Communications Commission) Standard
Video Heads: Two heads
Tape width: 1/2 inch (12.65 mm)
Tape speed
SP: 33.35 mm/sec.
LP: 16.67 mm/sec.
SLP: 11.12 mm/sec.
Operating Temperature: 41˚F (5˚C) to 104˚F (40˚C)
Relative Humidity: 10% to 75%
Power requirement: AC 120V, 60Hz
Power consumption: 65W (CCC130 and CCC132)
90W (CCC190 and CCC192)
Sound output: 1W
Dimensions:
15-3/4" (H) x 15-3/16" (W) x 14-13/16" (D)
400mm x 386mm x 377mm
(CCC130 and CCC132)
19-11/16" (H) x 19-7/16" (W) x 18-5/16" (D)
500mm x 494mm x 465mm
19-5/8" (H) x 19-3/8" (W) x 18-11/16" (D)
498mm x 492mm x 474mm
(CCC190)
(CCC192)
Weight: 24.3 lbs (11.0 kg) (CCC130 and CCC132)
Weight: 44.1 lbs (20.0 kg) (CCC190 and CCC192)
Tuner Broadcast Channels
VHF 2-13, UHF 14-69
Cable TV Channels
1-125
Term inals
Antenna In: VHF/UHF 75 ohms unbalanced
Video In: RCA connector
Audio In: RCA connector
Earphone: 3.5 mm CES
Electrical Specifications
Video input level: 0.5~2.0Vp-p
Audio input level: -10dBv
Video S/N ratio
SP: More than 42dBµ
Audio S/N ratio
SP: More than 38dB
Designs and specifications are subject to change without notice and without our
legal obligation.
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty 57
TV/VCR COMBINATION
90 Days Free Labor/One Year Free Parts Exchange (Two Years Free Exchange on Color Picture Tube)
This product must be carried in for repair.
WHO IS COVERED?
uct, the local Philips service organization will attempt
You must have proof of purchase to receive warranty to provide service (although there may be a delay if
service. A sales receipt or other document showing
that you purchased the product is considered proof
of purchase.
the appropriate spare parts and technical manual(s)
are not readily available).
MAKE SURE YOU KEEP...
WHAT IS COVERED?
Please keep your sales receipt or other document
showing proof of purchase. Attach it to this owner’s
manual and keep both nearby. Also keep the original
box and packing material in case you need to return
your product.
Warranty coverage begins the day you buy your
product. For 90 days thereafter, all parts will be
repaired or replaced, and labor is free. From 90 days
to one year from the day of purchase, all parts will be
repaired or replaced, but you pay for all labor
charges. From one to two years from the day of pur-
chase, you pay for the replacement or repair of all
parts except the picture tube, and for all labor
charges. After two years from the day of purchase, you
pay for the replacement or repair of all parts, and for
all labor charges.
BEFORE REQUESTING SERVICE...
Please check your owner’s manual before requesting
service. Adjustments of the controls discussed there
may save you a service call.
TO GET WARRANTY SERVICE IN U.S.A., PUER-
TO RICO OR U.S. VIRGIN ISLANDS...
Take the product to a Philips factory service center
(see enclosed list) or authorized service center for
repair. When the product has been repaired, you
must pick up the unit at the center. Centers may
keep defective parts.
All parts, including repaired and replaced parts, are
covered only for the original warranty period. When
the warranty on the product expires, the warranty on
all replaced and repaired parts also expires.
WHAT IS EXCLUDED?
Your warranty does not cover:
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all
implied warranties, including implied warranties of
merchantability and fitness for a particular purpose,
are limited in duration to the duration of this express
warranty. But, because some states do not allow limi-
tations on how long an implied warranty may last, this
limitation may not apply to you.)
• labor charges for installation or setup of the prod-
uct, adjustment of customer controls on the prod-
uct, and installation or repair of antenna systems
outside of the product.
• product repair and/or part replacement because of
misuse, accident, unauthorized repair or other
cause not within the control of Philips Consumer
Electronics.
• reception problems caused by signal conditions or
cable or antenna systems outside the unit.
• a product that requires modification or adaptation
to enable it to operate in any country other than
the country for which it was designed, manufac-
tured, approved and/or authorized, or repair of
products damaged by these modifications.
• incidental or consequential damages resulting from
the product. (Some states do not allow the exclu-
sion of incidental or consequential damages, so the
above exclusion may not apply to you. This
includes, but is not limited to, prerecorded materi-
al, whether copyrighted or not copyrighted.)
• damage caused by the use of non-VHS tapes or
tapes that have not been tested and labeled for
use in two, four, six, and eight hour VHS
recorders.
TO GET WARRANTY SERVICE IN CANADA...
Please contact Philips at:
1-800-661-6162 (French Speaking)
1-800-363-7278 (English Speaking)
(In Canada, this warranty is given in lieu of all other
warranties. No other warranties are expressed or
implied, including any implied warranties of mer-
chantability or fitness for a particular purpose. Philips
is not liable under any circumstances for any direct,
indirect, special, incidental or consequential damages,
howsoever incurred, even if notified of the possibility
of such damages.)
REMEMBER...
Please record below the model and serial numbers
found on the product. Also, please fill out and mail
your warranty registration card promptly. It will be
easier for us to notify you if necessary.
• a product that is used for commercial or institu-
tional purposes.
MODEL # __________________________________
SERIAL # __________________________________
WHERE IS SERVICE AVAILABLE?
Warranty service is available in all countries where
the product is officially distributed by Philips
Consumer Electronics. In countries where Philips
Consumer Electronics does not distribute the prod-
This warranty gives you specific legal rights. You may have
other rights which vary from state to state.
Philips Service Solutions Group, P.O . Box 2976, Longview, Texas 75606, (903) 242-4800
EL4963E006 / MAC 6108/ 03-00
Download from Www.Somanuals.com. All Manuals Search And Download.
58 Index
a-b repeat play . . . . . . . . .38-39
accessories . . . . . . . . . . . . . . .60
ant(enna) jack . . . . . . . . . . .6, 21
audio in jack . . . . . . . . .7, 20, 31
automatic
memory
button . . . . . . . . . . .23, 39-40
real-time counter . . . . . . . .40
rewind, power off . . . . . . .52
menu
button . . . . . . . . . . . . . . . .23
front panel button access . .20
mute button . . . . . . . . . . . . . .22
sqpb . . . . . . . . . . . . . . . . . . . .28
standard play . . . . . . . . . .29, 53
status display . . . . . . . . . . . . .26
status/exit button . . . . . . .23, 26
still picture . . . . . . . . . . . . . . .41
stop/p button . . . . . . . . . . . .23
stop/eject button . . . . . . . . . .20
super high speed searching . . .41
super long play . . . . . . . . .29, 53
playback . . . . . . . . . . . . . . .52
rewind . . . . . . . . . . . . . . . .52
batteries . . . . . . . . . . . . . . . . . .5
blue background . . . . . . . . . . .46
brightness, adjusting . . . . .24-25
number buttons . . . . . . . . . . .22
one-touch recording . . . . . . . .30
table of contents . . . . . . . . . . .4
tape
channel
duplication . . . . . . . . . . . . .31
speed . . . . . . . . . . . . . .29, 53
time
setting . . . . . . . . . . . . . .12-17
zone . . . . . . . . . . . . . . . . . .19
timer recording
cancelling . . . . . . . . . . . . . .35
reviewing . . . . . . . . . . . . . .35
setting . . . . . . . . . . . . . .32-34
tint, adjusting . . . . . . . . . . .24-25
tracking . . . . . . . . . . . . . . . . .52
above 100 . . . . . . . . . . . . .22
adding . . . . . . . . . . . . . . . .11
buttons . . . . . . . . . .20, 23, 52
deleting . . . . . . . . . . . . . . .11
reviewing . . . . . . . . . . . . . .11
setup . . . . . . . . . . . . . . . . .10
clear button . . . . . . . . . . . . . .22
clock . . . . . . . . . . . . . . . . .12-17
closed caption system . . . .50-51
color, adjusting . . . . . . . . .24-25
connections . . . . . . . . . . .6-7, 31
contents, table of . . . . . . . . . . .4
controls
pause/still button . . . . . . .23, 41
picture, adjusting . . . . . . . .24-25
play button . . . . . . . . . . . .20, 22
playback options . . . . . . . . . . .41
playing . . . . . . . . . . . . . . . . . .28
power
button . . . . . . . . . . . . .20, 22
cord . . . . . . . . . . . . . . . .7, 21
real-time counter memory . . .40
rear panel . . . . . . . . . . . . . . . .21
rec/otr button . . . . . . . . .20, 23
record light . . . . . . . . . . . . . .20
recording . . . . . . . . . . . . . . . .29
recording prevention . . . . . . . .5
reminder . . . . . . . . . . . . . . . .27
remote
video in jack . . . . . . . . .7, 20, 31
volume bar . . . . . . . . . . . . . . .49
remote . . . . . . . . . . . . .22-23
tv/vcr . . . . . . . . . . . . . . . . .20
counter only mode . . . . . . . . .26
wake up timer . . . . . . . . . . . .48
warranty . . . . . . . . . . . . . . . . .57
daylight-savings time . . . . . . . .18
defeat recording . . . . . . . . . . .36
duplication . . . . . . . . . . . . . . .31
control
buttons . . . . . . . . . .22-23
using . . . . . . . . . . . . . . . .5
sensor . . . . . . . . . . . . . . . .20
repeat play . . . . . . . . . . . . . . .37
rerecording . . . . . . . . . . . . . .31
rew(ind) button . . . . . . . . . . .20
rew(ind)/{ button . . . . . .23, 41
rewinding . . . . . . . . . . . . . . . .41
earphone jack . . . . . . . . . . . . .20
eject button . . . . . . . . . . . . . .22
fast forward search . . . . . . . . .41
f.fwd/B button . . . . . . . . .22, 41
f.fwd button . . . . . . . . . . . . . .20
front panel . . . . . . . . . . . . . . .20
safety precautions . . . . . . . . . .3
searching . . . . . . . . . . . . . . . .41
sensor (remote) . . . . . . . . . . .20
sharpness, adjusting . . . . . .24-25
showguard . . . . . . . . .32, 35, 54
sleep timer . . . . . . . . . . . . . . .47
slp . . . . . . . . . . . . . . . . . .29, 53
smartclock . . . . . . . . . . . . .14-17
smartlock . . . . . . . . . . . . .42-45
sp . . . . . . . . . . . . . . . . . .29, 53
specifications . . . . . . . . . . . . .56
glossary . . . . . . . . . . . . . . . . .53
helpful hints . . . . . . . . . . . .54-55
hookups . . . . . . . . . . . . .6-7, 31
language selection . . . . . . . . . . .9
line input mode . . . .7, 10, 31, 53
long play . . . . . . . . . . . . . .29, 53
lp . . . . . . . . . . . . . . . . . .29, 53
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
SUPPLIED ACCESSO RIES
The following items are supplied with your TV/VCR; they
are provided to help you use or set up your TV/VCR.
Remote Control for CCC130 and CCC190 4835 218 37307
Remote Control for CCC132 and CCC192 4835 218 37308
Two AA Batteries 4835 138 17012
O PTIO NAL ACCESSO RIES
The following additional items are not provided with your
TV/VCR, but they are designed for use with your new TV/VCR.
To order these optional accessories, contact us at:
Philips Parts & Accessories Marketing Department
401 East Old Andrew Johnson Highway
P.O. Box 555
Jefferson City, TN 37760
1-800-851-8885.
Monaural Audio and Video Cables (6 feet)
VHS Cassette Rewinder
#M61117
Color-coded for easy connection
#M61103
Three Cassette Storage Cases (plastic)
Fits VHS and Beta cassettes
#M61104
Six High-grade, VHS, T-120 Cassettes
#MHG1206
This owner’s manual is made of recyclable materials.
Remember to recycle!
As an ENERGY STAR® Partner, Philips Consumer Electronics
has determined that this product meets the
ENERGY STAR® guidelines for energy efficiency.
ENERGY STAR® is a U.S. registered mark.
IB8271E001
Printed In Mexico
0EMN01770 / T7260UL, T7261UM * * * * *
Download from Www.Somanuals.com. All Manuals Search And Download.
|