HDTV Monitor
55PP9401
60PP9401
Quick Use and Setup Guide
TABLE OF CONTENTS
Safety/Important Notice . . . . . . . . . . . . . . . . . . . . . . . .1
Best Viewing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Making a Basic Antenna or Cable TV Hookup . . . . . . .1
Making a Basic VCR Hookup . . . . . . . . . . . . . . . . . . .2
Using the Front Panel Jacks . . . . . . . . . . . . . . . . . . . . .2
Performing Basic TV Operations . . . . . . . . . . . . . . . . .3
Learning Remote Control Buttons . . . . . . . . . . . . . . . .3
Using the On-screen Menu . . . . . . . . . . . . . . . . . . . . . .4
Setting the Language Control . . . . . . . . . . . . . . . . . . . .4
Selecting the Tuner Mode . . . . . . . . . . . . . . . . . . . . . .5
Using the Auto Program Control . . . . . . . . . . . . . . . . .5
Using the Channel Edit Control . . . . . . . . . . . . . . . . . .6
Using the Channel List Control . . . . . . . . . . . . . . . . . .6
Setting the TV’s Clock . . . . . . . . . . . . . . . . . . . . . . . . .7
Using the Auto IntelliSense Focus Control . . . . . . . .7
Using the Formats Control . . . . . . . . . . . . . . . . . . . . . .8
Learning More about the Rear Panel Jacks . . . . . . . . . .8
WARNING: TO PREVENT FIRE OR
SHOCK HAZARD DO NOT EXPOSE
THIS UNIT TO RAIN OR EXCES-
SIVE MOISTURE.
™
HOOKING UP YOUR PROJECTION TV (BASIC TV CONNECTIONS)
BEST VIEWING
he major benefit of this projection
Ttelevision is its large viewing
screen. To see this large screen at its
best, test various locations in the
room to find the optimum spot for
viewing.
To avoid cabinet warping, cabinet
color changes, and increased
chance of set failure, do not place
the TV where temperatures can
become excessively hot—for exam-
ple, in direct sunlight or near a
heating appliance.
Magnetic fields, such as those of
external speakers, may cause the
picture to distort if the speakers
are placed too close to the televi-
sion. Move the magnetic field
source away from the TV until
there is no picture distortion.
NOTE: Be sure to allow a free flow
of air to and from the perforated
back cover of the set.
ANTENNA/CABLE TV HOOKUP
CHECK IT OUT
he TV signal coming into your
Thome may be from a Cable TV
company or a combination UHF/VHF
antenna. In either case, the basic con-
nection to the TV is very easy.
✔ To set the TV to
Connect the coaxial cable/con-
nector to the ANT(enna) A input on the
back of the TV.
If you’re using a cable converter box,
connect the OUT(put) plug from the
converter to the ANT(enna) A input on
the back of the TV.
If the TV signal is from a 75Ω
F-type coaxial cable/connector,
then you’re ready to connect it to the
antenna input on the back of the TV.
If you’re using a cable signal with a
convertor box, first connect the cable
TV signal to the cable signal IN(put)
plug on the converter box. Then con-
nect from the OUT(put) on the con-
verter box to the ANT(enna) input on
the back of the TV.
select only the chan-
nel numbers in your
area see how to
“Program" or "Add"
channels in memory
on page 5 (Auto
A Cable TV signal may use a cable
box or a direct connection and can
receive up to 125 channels.
Program section).
✔ If you intend to
A UHF/VHF antenna can receive
normal broadcast channels 2–13 for
VHF and 14–69 for UHF band sig-
nals.
use separate UHF
and VHF antennas,
you will need an
optional combiner to
connect to the TV.
To order any option-
al accessory contact
your dealer or call
the toll-free accesso-
ry ordering number
(1-800-851-8885).
Unless your TV is connected to a
cable TV system or to a centralized
antenna system, a good outdoor color
TV antenna is recommended for best
performance. But if you are located in
an area with an exceptionally good
signal that is free from interference
and multiple image “ghosts,” an
indoor antenna may be sufficient.
Combination VHF/UHF
Antenna
(Outdoor or Indoor)
Note: A 300Ω to 75 Ω Adapter may be
required if the UHF/VHF antenna you are
using has a “twin-lead wire” instead of the
300Ω to 75Ω
Adapter
single F-type 75Ω coaxial cable/connector.
(483521827003)
✔ See page 8 for
Twin-lead
Wire
more information on
the Rear Panel
jacks.
F-type 75Ω Coaxial
Cable/Connector
1
F-type 75Ω
Coaxial
TV Signal from
Cable Company
ANT A
Cable/Connector
Cable Converter Box
OR
OUT
IN
Back of TV
2
F-type 75Ω Coaxial
Cable/Connector
EL6487E002 H462952
Download from Www.Somanuals.com. All Manuals Search And Download.
PERFORMING BASIC TV OPERATIONS
CHECK IT OUT
TELEVISION
✔ Your TV will
n this section, learn how
Ito use the TV buttons for
basic operation of the TV.
(See page 4 for information on
how to adjust or set TV con-
trols through the on-screen
menu using the buttons on the
front of the TV, if you don’t
want to use the remote.)
Press the POWER
button to turn the TV on.
Press the CH(annel) selec-
tor buttons until the number of
the channel you desire appears
in the right corner of the TV
screen.
Press the VOL(ume) level
buttons to attain your desired
sound level. The volume level
will be displayed on the TV
screen.
appear to be turned
off if no video input
is present when
After having connected
a broadcast signal source to
the TV, press the INPUT/EXIT
button to select a source. The
source options are Tuner A,
Tuner B, A/V: 1, A/V: 2, Front,
A/V: 3, and A/V: 4. For this
example, choose the source to
which you connected the
broadcast signal (Tuner A or
Tuner B).
A/V:1, A/V: 2,
FRNT, A/V: 3, or
A/V: 4 are selected.
Check the Power
Light to make sure
the TV is turned off
when not in use.
✔ Your remote
does not have an
INPUT button. Use
the SOURCE button
to choose among
signal sources. You
can also use the
AV 1, AV 2, AV 3,
and AV 4 buttons to
access signal
Remote Control Sensor—point
your remote at this area when
selecting channels, adjusting
volume, and sending other
commands with the remote.
sources.
ImageMax™ Sensor—this will
make automatic picture adjust-
ments based on the amount of
light in the room to give the
best picture.
Press the indention on the Front
Panel to access the Front Panel
Jacks.
1
Power Light—you will see a
red light when the TV is turned
on.
PUSH
CH+
CH-
POWER INPUT MENU
VOL-
VOL+
EXIT
SELECT
POWER button—With the TV
Front Panel Jacks (“FRNT” inputs)—Use these
audio/video jacks for a quick hookup from a
camcorder or VCR to instantly view your
favorite show or new recording. Press the
INPUT/EXIT button on the TV until “FRNT”
appears in the top right corner of the TV screen.
If you have mono sound, insert the audio cable
into the left audio jack.
off, press and hold this button for
five seconds to see an auto-
demonstration of the on-screen
displays with HELP text.
CH+
CH-
POWER INPUT
MENU
VOL-
VOL+
EXIT SELECT
REMOTE
Offering direct access to the on-screen menu, this remote
controls all features and functions of your TV. It also con-
trols virtually all infrared VCRs, laserdisc/DVD players,
and satellite receivers, as well as on/off and channel
up/down on most cable converter/decoders (see pages
31–36 of the Directions for Use manual for setup informa-
tion).
SOURCE Button—Press to choose from among the TV’s
signal sources: Tuner A, Tuner B, A/V: 1, A/V: 2, FRNT
(Front), A/V: 3, or A/V: 4.
Mode Buttons—This remote can be set up to operate a
VCR, DVD, laserdisc, cable box, or satellite receiver. Press
TV to use the remote with the TV, DVD for DVD and
laserdisc, VCR for VCR, and ACC(essory) for a cable box
or satellite receiver. (See the Directions for Use manual.)
HELP Button—Press when a menu is on screen to view
HELP text. The text gives a description of the displayed
menu. The HELP text will be shown every time a MENU
is displayed, until you press the HELP button again.
FORMAT Button—Press to quickly change the aspect
ratio of the viewable video. Choose from 4:3, Zoom, 16:9,
and Theater.
STATUS/EXIT Button—Press to display the time (after
you have set it) and status of sound (stereo or mono), sig-
nal source, and screen format. Also press to clear the TV
screen after setting or adjusting controls.
VOL(ume) +, – Buttons—Press + or – until you obtain
the volume level you want.
A/CH (Alternate Channel) Button—Press to choose
between the last two channels viewed. (This is good for
switching between two sporting events, for example.)
INTELLISENSE Button—Press to automatically adjust
picture convergence using Auto IntelliSense Focus.
TUNER A, TUNER B, and FRONT Buttons—Press to
access either of the two tuners in the TV’s Rear Panel or the
audio/video jacks in the TV’s Front Panel.
SOURCE
POWER Button—Press to turn the TV on or off. With the
TV off, press and hold this button for five seconds to see an
auto-demonstration of the on-screen displays with HELP text.
LIGHT Button—Press to back-light the remote control.
PIP Buttons—Press to perform Picture-in-Picture feature
functions. See the section on Picture-in-Picture in the
Directions for Use manual for details.
OK Button—Press to make selections in the on-screen menu.
CURSOR Buttons—Press LEFT, RIGHT, UP, or DOWN to
move through, select, and adjust on-screen menu options.
MENU/SELECT Button—Press to access the TV’s on-
screen menu.
CH(annel) +, – Buttons—Press to cycle through all stored
channels that have been placed in TV memory after the “Auto
Programming” function of the TV has been completed.
MUTE Button—Press to reduce the sound to one-half the
normal volume (Soft Mute) (good to use when answering the
telephone). Press the MUTE button again to turn the sound off
completely. Press the button once more to restore the sound, or
press the VOL(ume) + button.
DVD
TV
VCR
ACC
HELP
LIGHT
FORMAT
SWAP
PIP CH
SOURCE FREEZE
PIP ON/OFF
+
–
PIP POSITION
STATUS/
EXIT
MENU/
SELECT
VOL
CH
1
4
2
5
8
0
3
6
7
9
NUMBER Buttons—Press to directly access any numbered
channel.
SURF Button—Press to access the Favorite Channel screen.
Favorite Channel simplifies surfing (going from channel to
channel). It allows you to store up to 36 favorite stations in the
A/CH
SURF
QTR
INTELLISENSE
™
Surf memory. Favorite Channel has 6 categories with 6
channels per category. Add or delete channels from the on-
screen list
VCR Buttons—Press the VCR buttons to activate certain
VCR commands when the remote is in the VCR mode. The
buttons are for PLAY, STOP, REWIND, FAST FORWARD,
PAUSE, RECORD, AND TIMER features.
TUNER A TUNER B FRONT
AV1
AV2
AV3
AV4
AV1, AV2, AV3, AV4 Buttons—Press to access the four
audio/video input options on the TV’s Rear Panel.
REMOTE BATTERIES
Remove the battery
compartment lid on the back
of the remote.
Reattach the battery
Place the batteries (2-AA)
in the remote. Be sure the (+)
and (-) ends of the batteries
line up correctly (inside of case
is marked).
Battery Usage CAUTION—To pre-
vent battery leakage which may
result in bodily injury or damage to
the unit:
lid.
• Install ALL batteries correctly, + and
– as marked on the unit.
• Do not mix batteries: (OLD and NEW
or CARBON and ALKALINE, etc.)
• Remove batteries when the unit is
not used for a long time.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE ON-SCREEN MENU
MENU
his section explains how
Tto make selections or
adjustments within the on-
screen menu. The menu is
simply a list of your TV’s
features or controls. Use the
CURSOR buttons on your
remote control or the
To highlight a feature within
the menu, press the CURSOR
DOWN or UP button on the
remote. Or press the CH(annel)
selector buttons on the TV.
To make selections, press the
OK button on the remote or the
MENU/SELECT button on the
TV. To adjust Picture or Sound set-
tings, press the CURSOR RIGHT
or LEFT buttons on the remote. Or
press the VOL(ume) –, + buttons
on the TV.
Press the
MENU/SELECT button on the
remote to display the On-screen
Menu. Or press the
MENU/SELECT button on the
TV.
To move through the list of
options and their setting or
adjustment areas, press the CUR-
SOR DOWN, UP, RIGHT, or
LEFT buttons. Or press the
CH(annel) selector or VOL(ume)
buttons on the TV.
To choose an item from
the Menu Bar, press the CUR-
SOR RIGHT or LEFT button. Or
press the VOL(ume) level buttons
on the TV.
To remove the on-screen
menu, press the STATUS/EXIT
button on the remote. Or press the
INPUT/EXIT button on the TV.
CH(annel) selector and
VOL(ume) buttons on the
TV to move among the
menu options. As necessary,
on-screen messages will
provide you with informa-
tion to guide you. Also, with
the on-screen menu dis-
played, you can press the
HELP button on the remote
control to receive more on-
screen assistance.
OK
SETUP
FEATURES PICTURE
SOUND
THEATER
Language
Tuner Mode
Auto Program
Channel Edit
Channel List
Clock Set
Menu Bar
List of Options
for Selected
Menu Bar
Item
IntelliSense
Formats
To Quit Exit
5
ON THE TV
PUSH
CH+
CH-
POWER INPUT ENU
VOL-
VOL+
EXIT
SELECT
ON THE REMOTE
3
4
4
2
1
USING THE SETUP CONTROLS
LANGUAGE
he Language control
Twill allow you to select
any of three languages for
all on-screen displays.
Press the MENU/SELECT
button on the remote control to show
the on-screen menu.
Press the CURSOR RIGHT but-
ton to enter the Language options
area.
Press the OK button to select
the language.
To return to the list of Setup
options, press the CURSOR LEFT
button. To return to the Menu Bar,
press the MENU/SELECT button. To
quit the on-screen menu, press the
STATUS/EXIT button.
Press the CURSOR DOWN
button to highlight Language.
Press the CURSOR DOWN or
UP button to highlight the Language
of your choice.
P r e s s O K t o s e t
OK
SETUP
FEATURES PICTURE
SOUND
THEATER
OK
SETUP
Menu To Menu Bar
To Quit Exit
Menu To Menu Bar
To Quit Exit
6
3
4
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE SETUP CONTROLS
CHECK IT OUT
TUNER MODE
✔ The reception
y choosing a Tuner Mode,
Byou are telling the TV the
type of broadcast signal you
have connected. Select Antenna
if you are using an indoor or
outdoor antenna. Choose
Cable 1 or Cable 2 if you have
cable TV.
Press the
Press the CURSOR
To return to the list of
channels for the
Antenna and Cable
signal sources are
shown below.
MENU/SELECT button on
the remote control to show the
on-screen menu.
RIGHT button to move to the
Tuner Mode options area. Press
the CURSOR DOWN or UP
button until you have high-
lighted the correct option.
Setup options, press the CUR-
SOR LEFT button. To return to
the Menu Bar, press the
MENU/SELECT button. To
quit the on-screen menu, press
the STATUS/EXIT button.
✔ Refer to your
Press the CURSOR
DOWN button twice until
Tuner Mode is highlighted.
cable or TV guide
for channel identifi-
cation standards.
Press the OK button to
make your selection.
✔ If certain cable
channels are poor or
not possible in
Cable 1 mode, set
Tuner Mode to
Cable 2.
P r e s s O K t o s e t
OK
SETUP
FEATURES PICTURE
SOUND
THEATER
OK
SETUP
Language
Language
Tuner Mode
Auto Program
Channel Edit
Channel List
Clock Set
Antenna
Cable 1
Cable 2
Tuner Mode
Auto Program
Channel Edit
Channel List
Clock Set
Antenna
Cable 1
Cable 2
IntelliSense
Formats
IntelliSense
Formats
Menu To Menu Bar
To Quit Exit
Menu To Menu Bar
To Quit Exit
P r e s s O K t o s e t
OK
SETUP
5
Language
Tuner Mode
Auto Program
Channel Edit
Channel List
Clock Set
Antenna
Cable 1
Cable 2
3
IntelliSense
Formats
Menu To Menu Bar
To Quit Exit
Reception Band
Cable 1 or Cable 2
Cable Channel
Indicated on
Air
(Antenna)
the screen
2 ~ 13
VHF 2~13
14 ~ 22
95 ~ 99
23 ~ 36
37 ~ 64
Midband A~1
A-5 ~ A-1
VHF 2 ~ 13ch
Super band J~W
Hyperband
UHF 14 ~ 69ch
W + 1 ~ W + 28
65 ~ 125
Ultraband
W + 29 ~ W + 84
CHECK IT OUT
AUTO PROGRAM
✔ If you press the
se this control to automatically
Ustore active TV channels in the TV’s
memory. This will allow you to skip
unused channels when using the
To return to the list of
Setup options, press the
CURSOR LEFT button. To
return to the Menu Bar, press
the MENU/SELECT button.
To quit the on-screen menu,
press the STATUS/EXIT but-
ton.
Press the
Press the CURSOR
RIGHT button to highlight
Search.
EXIT button while
the Auto Program
function is working,
programming will
stop.
MENU/SELECT button on
the remote control to show
the on-screen menu.
CH(annel) +, – buttons on your remote.
Press the OK button
to start searching for chan-
nels and programming the
TV’s memory.
Press the CURSOR
DOWN button repeatedly
until Auto Program is high-
lighted.
✔ If you connect
two antennas, switch
antenna inputs with
the INPUT button
and repeat Auto
Program for the sec-
ond antenna input.
P r e s s O K t o s e t
OK
SETUP
FEATURES PICTURE
SOUND
THEATER
OK
SETUP
✔ Remember to
select the correct
Tuner Mode before
using Auto Program
(see the Tuner Mode
section).
Language
Language
Tuner Mode
Auto Program
Channel Edit
Channel List
Clock Set
Tuner Mode
Auto Program
Channel Edit
Channel List
Clock Set
□
□
Search
Search
IntelliSense
Formats
IntelliSense
Formats
✔ See Channel Edit
to learn how to add
Menu To Menu Bar
To Quit Exit
Menu To Menu Bar
To Quit Exit
4
or delete channels.
OK
SETUP
FEATURES PICTURE
SOUND
THEATER
5
Auto Program
ࠜ
Searching
Channel 22
3
88% Complete
Menu To Menu Bar
To Quit Exit
5
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE SETUP CONTROLS
CHANNEL EDIT
elect the correct Tuner Mode and run
SAuto Program to automatically store
active TV channels (see the sections on
those controls in this publication). Then
use Channel Edit to add or delete chan-
nels from the TV’s memory.
To return to the list of
Setup options, press the
CURSOR LEFT button. To
return to the Menu Bar, press
the MENU/SELECT button.
To quit the on-screen menu,
press the STATUS/EXIT but-
ton.
Press the
Press the CURSOR
DOWN or UP button to
highlight Add or Delete.
MENU/SELECT button on
the remote control to show
the on-screen menu.
To Add or Delete the
current channel, press the
OK button. If you want to
Add or Delete a different
channel, press the CH(annel)
+ or – buttons to select the
desired channel.
Press the CURSOR
DOWN button repeatedly
until Channel Edit is high-
lighted.
Press the CURSOR
RIGHT button to enter the
Add/Delete area.
P r e s s O K t o s e t
OK
SETUP
FEATURES PICTURE
SOUND
THEATER
OK
SETUP
Language
Language
Tuner Mode
Auto Program
Channel Edit
Channel List
Clock Set
Tuner Mode
Auto Program
Channel Edit
Channel List
Clock Set
Channel 2
Add
Channel 2
Add
Delete
Next Ch
Delete
ᮡ
ᮢ
IntelliSense
Formats
IntelliSense
Formats
Ch Ch
Or #Keys
Menu To Menu Bar
To Quit Exit
Menu To Menu Bar
To Quit Exit
P r e s s O K t o s e t
OK
SETUP
6
Language
Tuner Mode
Auto Program
Channel Edit
Channel List
Clock Set
Channel 2
Add
Delete
3
Next Ch
ᮡ
ᮢ
IntelliSense
Formats
Ch Ch
Or #Keys
Menu To Menu Bar
To Quit Exit
CHANNEL LIST
hannel List allows you to
To return to the list of
Setup options, press the
CURSOR LEFT button. To
return to the Menu Bar, press
the MENU/SELECT button.
To quit the on-screen menu,
press the STATUS/EXIT but-
ton.
Press the
Press the CURSOR
Creview labeled channels
MENU/SELECT button on
the remote control to show
the on-screen menu.
RIGHT button to view the
Channel List. When in the
Channel list, pressing the
CURSOR DOWN or UP but-
ton will allow you to view
the next eight channels.
(Id). It also shows you which
channels have been added to the
TV’s memory and which ones
are protected by AutoLock.™ See
the section on Channel Edit in
this publication. Learn more
about Channel List and
Press the CURSOR
DOWN button repeatedly
until Channel List is high-
lighted.
AutoLock in the Directions for
Use manual that came with your
TV.
OK
SETUP
FEATURES PICTURE
SOUND
THEATER
OK
SETUP
FEATURES PICTURE
SOUND
THEATER
Language
Channel List
TunerA
ᮡ
Tuner Mode
Auto Program
Channel Edit
Channel List
Clock Set
Ch
Id
Scan
Lock
--
--
--
--
--
ON
--
2
3
4
5
6
7
8
NBC
ABC
CBS
****
CNN
COM
ESPN
ON
ON
ON
--
ON
ON
ON
IntelliSense
Formats
ᮢ
Menu To Menu Bar
To Quit Exit
Menu To Menu Bar
To Quit Exit
OK
SETUP
FEATURES PICTURE
SOUND
THEATER
4
Channel List
TunerA
ᮡ
Ch
Id
Scan
Lock
9
ESP2
ON
ON
ON
--
ON
ON
ON
--
ON
--
--
--
10 HBO
11 HGTV
3
12
13
14
****
FOX
BET
--
--
ᮢ
15 AMC
Menu To Menu Bar
To Quit Exit
6
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE SETUP CONTROLS
CLOCK SET
ou must set the time on the TV’s
Yclock before you can use the 4 Event
Program or Sleep Timer (see the
Directions for Use manual for details on
those features).
Press the MENU/SELECT
button on the remote control to
show the On-screen Menu.
Press the CURSOR RIGHT
button to enter the Clock Set area.
After you have finished
inputting the time, press the
MENU/SELECT button to return to
the Menu Bar. Or press the STA-
TUS/EXIT button to quit the on-
screen menu.
Press the CURSOR DOWN
or UP button to select digits for the
hour. Press the CURSOR RIGHT
button to move to the input area for
the minutes. Press the CURSOR UP
or DOWN to choose the digits for
the minutes. Choose Am or Pm, the
month, day, and year in the same
manner.
Press the CURSOR DOWN
button repeatedly until Clock Set is
highlighted.
ᮡ
ᮢ
To s e t t i m e
OK
SETUP
FEATURES PICTURE
SOUND
THEATER
OK
SETUP
Language
Clock Set
Tuner Mode
Auto Program
Channel Edit
Channel List
Clock Set
:__ Am Jan 1 2001
IntelliSense
Formats
Menu To Menu Bar
To Quit Exit
Menu To Menu Bar
To Quit Exit
ᮡ
ᮢ
To s e t t i m e
OK
SETUP
Clock Set
12:00 Pm May 1 2001
3
Menu To Menu Bar
To Quit Exit
CHECK IT OUT
INTELLISENSE
✔ After Auto
ou can automatically adjust the TV’s
Ypicture convergence using Auto
IntelliSense Focus. Your projection TV
has three color projection tubes: one for
red, one for green, and one for blue.
When mixed in the proper proportion,
the output of these three color tubes can
produce any color. However, the beams
of light coming from the tubes must be
precisely aligned over each other so that
the colors can be mixed. The alignment
of these picture beams is called “conver-
gence.”
Press the INTEL-
LISENSE button on your
remote control to begin
adjusting the TV’s conver-
gence. The process takes
about 15 seconds.
NOTE: During the adjust-
ment process, do not press
the INTELLISENSE button
again and do not move the
TV.
IntelliSense Focus
does its work, the
picture will be at its
best.
✔ You can also
access Auto
IntelliSense Focus
through the Setup
Menu.
Picture Difficulty:
Color fringes
around objects
INTELLISENSE
Over a period of time, the picture tubes
can drift out of alignment because of
normal bumps and vibrations or moving
the TV. If you move your TV, or if, after
a time, you notice color rings or halos
around objects, use Auto IntelliSense
Focus to adjust the convergence. This is
how Auto IntelliSense Focus works:
After reviewing a special test pattern,
optical sensors send position informa-
tion to a controller, which then corrects
the picture. Auto IntelliSense Focus
responds to the natural and man-made
magnetic field conditions where the pro-
jection TV is located, so you always
enjoy the best possible picture.
Color Fringes Gone:
Convergence adjusted
SOURCE
TV
DVD
VCR
ACC
HELP
LIGHT
FORMAT
SWAP
PIP CH
SOURCE FREEZE
PIP ON/OFF
+
–
PIP POSITION
STATUS/
EXIT
MENU/
SELECT
VOL
CH
1
4
2
5
8
0
3
6
7
9
A/CH
SURF
1
QTR
INTELLISENSE
TUNER A TUNER B FRONT
AV1
AV2
AV3
AV4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE SETUP CONTROLS
CHECK IT OUT
FORMATS
.✔ If Comp Color
he Formats control is very useful
Twhen setting up reception for High
Definition, Standard Definition, and
NTSC signals. The Comp Color Type
function allows you to automatically
change tint and color coordinate for
DTV programs. Use the HDTV (High
Definition Television) setting for a High
Vision Signal (Y-PbPr) from an HDTV
set-top box. Use the SDTV/DVD setting
for Standard Definition Television or
Digital Video Disc (Y-CbCr) such as a
digital video disc player.
Press the
MENU/SELECT button on
the remote control to show
the on-screen menu.
Press the OK button to
make your selection. Repeat
steps 4 and 5 to set
V. Position/Comp Color Type
and Video Display.
Press the CURSOR
RIGHT button to enter the
Formats selection area.
Type is set improp-
erly (does not match
the actual input sig-
nal), the color and
tint of the main pic-
ture will be abnor-
mal.
Press the CURSOR
DOWN or UP button to
highlight a screen format you
want to select for the TV pic-
ture.
Press the CURSOR
DOWN button repeatedly
until Formats is highlighted.
To return to the list of
Setup options, press the
CURSOR LEFT button. To
return to the Menu Bar, press
the MENU/SELECT button.
To quit the on-screen menu,
press the STATUS/EXIT but-
ton.
✔ You must be
tuned to A/V: 3 or
A/V: 4 and have an
accessory device
hooked up to the
Y-PbPr input jacks
to access all of the
Formats Menu
options.
✔ All settings will
P r e s s O K t o s e t
OK
SETUP
FEATURES PICTURE
SOUND
THEATER
OK
SETUP
affect only the com-
ponent input you are
currently viewing. If
you are using both
sets of component
input jacks, be sure
to set Formats for
both inputs (set
Formats
Screen Formats
Tuner A
4x3
2
Language
ࠗ
ࠗ
ࠗ
ࠗ
ࠗ
Tuner Mode
Auto Program
Channel Edit
Channel List
Clock Set
16x9
Zoom
Theater
16x9-HD
5
V. Position
Comp Color Type
+
ࠗ
ࠗ
ࠗ
ࠗ
HDTV
IntelliSense
Formats
SDTV/DVD
i-laced
proscan
Video Display
Menu To Menu Bar
To Quit Exit
Menu To Menu Bar
To Quit Exit
A/V: 3 and A/V: 4).
6
3
LEARNING MORE ABOUT THE REAR PANEL JACKS
JACK DESCRIPTIONS
our TV’s Rear Panel jacks allow the connection
Yof a variety of accessory devices (“compo-
nents”). This section explains how you may use the
jacks.
Component: Y-PbPr Inputs
AV 3 and AV 4 provide Y-PbPr jacks for connecting equipment with Component Video capability.
Devices such as DVD players or set-top boxes can be connected to these jacks. You may use standard
video signal for AV 3 and AV 4.
NOTES:
• Your component inputs may be labeled Y, B-Y, and R-Y. In this case, connect the components
B-Y output to the TV’s Pb input and the components R-Y output to the TV’s Pr input.
• Your component outputs may be labeled Y-CbCr. In this case, connect the component output to the
TV’s Pb input and the component Cr output to the TV’s Pr input.
• It may be necessary to adjust Tint to obtain optimum picture quality when using the Y-PbPr inputs.
• To ensure no copyright infringement, the MONITOR OUT output will be abnormal when using
the Y-PbPr jacks.
S-VIDEO Inputs 1 and 2
• When using the Y-PbPr jacks, the TV will automatically change to Split PIP mode. When you have
Picture-in-Picture on and are viewing a Y-PbPr input, only Split mode is possible.
• AV 3 and AV 4 (Y/VIDEO) can be used for standard video input.
AV 1 and AV 2 provide S-VIDEO (Super
Video) jacks for connecting equipment
with S-VIDEO output capability.
Antenna Input/Output
The remote control allows you to switch between two
separate 75-ohm RF antenna inputs, ANTA and ANT B.
The ANT A input can be displayed as a main picture or
subpicture. ANT B can be displayed only as a main
picture. (ANT B cannot be displayed as a subpicture.)
The antenna output labeled “TO CONVERTER” allows
the ANT A connection to pass directly to a different
source such as a cable box only when ANT B is
displayed as the main picture.
MONITOR OUT
These jacks provide fixed audio and
video signals for recording. Use the
S-VIDEO Output for high-quality
video output. NOTE: S-VIDEO
Output may be used for recording
only when the input is of S-VIDEO
type.
AUDIO TO HI-FI Output
These jacks provide variable audio
output to a separate stereo amplifier.
With this connection, the audio to the
stereo can be controlled by the
television’s main volume.
Audio/Video Inputs 1, 2, 3, and 4
The SOURCE button or your remote will step through each video source and antenna source input
each time it is pressed. Use the audio and video inputs to connect accessory devices—VCRs,
camcorders, laserdisc players, DVD players and the like. (If you have mono sound, insert the audio
cable into the left audio jack.) NOTE: You may use VIDEO or S-VIDEO inputs to connect AV 1
and AV 2, but only one of these inputs may be used at a time.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
|