IEEE 802.3af
Power over Ethernet Splitter
POE-152S-5V/12V
User’s Manual
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
1. INTRODUCTION.......................................................................................................................................... 4
1.1 CHECKLIST ................................................................................................................................................ 4
1.2 ABOUT THE POWER OVER ETHERNET SPLITTER .......................................................................................... 4
1.3 FEATURES ................................................................................................................................................. 4
1.4 SPECIFICATION .......................................................................................................................................... 5
1.5 PRODUCT OUTLOOK................................................................................................................................... 5
2. HARDWARE INSTALLATION..................................................................................................................... 6
2.1 BEFORE INSTALLATION............................................................................................................................... 6
2.2 POE-152 AND POE-152S, THE IEEE 802.3AF INJECTOR AND SPLITTER INSTALLATION................................ 7
2.3 CONNECT WITH IEEE 802.3AF DEVICES...................................................................................................... 8
3.TROUBLESHOOTING................................................................................................................................... 9
APPENDIX A NETWORKING CONNECTION ............................................................................................... 10
A.1 SWITCH‘S RJ-45 PIN ASSIGNMENTS......................................................................................................... 10
A.2 RJ-45 CABLE PIN ASSIGNMENT................................................................................................................. 10
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1. INTRODUCTION
1.1 Checklist
Thank you for purchasing our POE-152S IEEE 802.3af Power over Ethernet Splitter, your Power over Ethernet
Splitter package shall contain following contents:
Check the contents of your package for following parts:
ò
ò
ò
ò
Power over Ethernet Splitter x 1
User's manual CD x 1
DC Plug Cable x 2
15cm UTP straight network cable x 1
If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton including the orig
use them against to repack the product in case there is a need to return it to us for repair.
1.2 About the Power over Ethernet Splitter
The PLANET POE-152S is an IEEE 802.3af Power over Ethernet device that split the 48V DC over the Ethernet cable into
5/12V DC power output. Work with the IEEE 802.3af power source equipment (PSE), the POE-152S frees the device
deployment from restrictions due to power outlet locations, which eliminate the costs for additional AC wiring and reduces
the installation time.
When the PSE inserts DC Voltage into the CAT 5 cable, it allows the cable between the PSE and POE-152S to transfer
data and power simultaneously. The maximum distance between the PSE and POE-152S is 100M. With being installed,
the PSE combines the Ethernet digital data with power over the twisted pair cables as an injector, and POE-152S, the
splitter, shall separate the digital data and the power into two outputs.
With IEEE 802.3af Power over Ethernet being installed, the system administrator only has to use a single RJ-45 Ethernet
cable to carry both power and data to each device. The POE-152S also have the benefits of cost saving, as well as ease
for networking planning and higher reliability. Furthermore, upon any IEEE 802.3af being installed, the POE-152S can
make the connection while migrating or splitting the power and the Ethernet digital packets. Providing two kinds of DC
output, the POE-152S offers 2.5A and 1A DC for current model POE-152S-5V and POE-152S-12V.
1.3 Features
Complies with IEEE 802.3af, Power over Ethernet, IEEE 802.3/802.3u/802.3ab 10/100/1000Base-T
Splits the 48V DC power over RJ-45 Ethernet cable into different DC output
LED indicators power input indication
Distance up to 100 meters
Choice of splitter for 5V DC and 12V DC
Auto-detect of POE IEEE 802.3af equipment, protect devices from being damaged by incorrect installation
Works with EIA568, category 5/5e/6,2/4-pair cables for 10Base-T or 100Base-TX and 1000Base-T
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 Specification
Model
POE-152S
Ethernet Connector
Ethernet Data Rate
Output Voltage/Current
2 x RJ-45 (1 for Data + DC in, 1 for Data out)
10/100/1000Mbps (vary on Ethernet device attached)
Vary on model:
POE-152S-5V: 5VDC, 2.5A max.
POE-152S-12V: 12VDC, 1A max.
1
TIA/EIA-568, Category 5/5e/6 cable
1 x POE ready/in-use
Number of Device can be powered
Ethernet Cable
LED indicator
Operating environment
Storage environment
Dimension (W x D x H)
Weight
0~50 Degree C, 5%~90%RH
-20~70 Degree C, 5%~90%RH
73 × 55 × 24 mm
50g
Emission
FCC Class B, CE mark
Standard Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3af Power over Ethernet
1.5 Product Outlook
LED definition:
LED
Color
Function
Lights to indicate the port is providing 48VDC in-line power.
PoE ready / in-use
Green
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2. HARDWARE INSTALLATION
These products provide three different running speeds – 10Mbps, 100Mbps,1000Mbps. in the same device and auto-
matically distinguish the speed of incoming connection.
This section describes the hardware features of POE-152S. Before connecting any network device to the POE-152S, read
this chapter carefully.
2.1 Before Installation
Before your installation, it is recommended checking your network environment. If there is any issue for your install a
networked device where is very difficult to find a power socket for your AC-DC adapter, the POE-152S can work with
POE-152 IEEE 802.3af Power over Ethernet Injector with an AC-DC adapter(DC 48V input). The POE-152S provide you
a way to provide DC power for this Ethernet device conveniently and easily.
The10/100/1000Mbps speed duplex mode from Ethernet port of POE-152S depends on which Ethernet device attached.
@Notice:
The POE-152 and POE-152S can be installed in pair. However, the use of third-party device is allowed if the device
complied with IEEE 802.3af standard.
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 POE-152 and POE-152S, the IEEE 802.3af Injector and Splitter installation
1. Connect a standard network cable from “Ethernet+DC” of POE-152 to “Ethernet+DC” of POE-152S. The POE LED of
POE-152 / POE-152S will light on continuance. The screen in Figure 1 appears.
From POE-152 or IEEE 802.3af
Power Supply equipment
Figure 1: Connection to POE-152 or IEEE 802.3af POE equipment
2. Connect the UTP cable in the package from “Ethernet” of POE-152S to the RJ-45 port of remote device.
3. Connect proper DC plug from “DC OUT” of POE-152S to remote device.
4. Power on the remote device and the LED indicator on POE-152S will remains on, the screen in Figure 2 appears.
Figure 2: Connection architecture over POE-152/152S
@Notice:
1. The POE-152S only accept IEEE 802.3af power supply equipment, any other in-line power device sending power
through UTP wire connects to POE-152S may cause the POE-152S malfunction.
2. Please ensure the output voltage is correct before applying power to remote device.
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2.3 Connect with IEEE 802.3af devices
The POE-152S can also provide the alternative to make the non- IEEE 802.3af devices the possibility to connect with an
IEEE 802.3af in-line power device like Power over Ethernet Switch, then connect proper DC plug from "DC OUT" of
POE-152S to remote device. The screen in Figure 3 appears.
Figure 3: Connect to IEEE 802.3af device
Once POE-152S detects the existence of an IEEE 802.3af device, the LED indicator will be steady; ON to shows it is
getting power.
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.TROUBLESHOOTING
This chapter contains information to help you solve issues. If the POE-152S is not functioning properly, make sure the
POE-152S was set up according to instructions in this manual.
The PoE LED is not lit
Solution:
Check the cable connection between POE-152S and IEEE 802.3af device.
Why the device connected to POE-152S cannot be powered?
Solution:
1. Please check the POE-152S is connect with an IEEE 802.3af complied in-line device like POE-152, and check if
the POE LED indicator at POE-152S is steady blink once attach to the IEEE 802.3af in-line power device. Then
connect the DC plug cable to the device you would like to power on.
2. Please check the cable type of the connection from one end to the other end. The cable should be an 8-wire
UTP, Category 5 or above, EIA568 cable within 100 meters. A cable with only 4-wire, short loop or over 100
meters, all will affect the power supply.
3. Please check the power requirement of the device you would like to power and check the label of the POE-152S
if it meets the requirement. There are two models of POE-152S for different power output, DC 5V and DC 12V.
4. Please check the specification of the powered device. If the device is over the specification of POE-152S, the
LED indicator of POE-152S will blink instead of stead green. The maximum currents that POE-152S can supply
are: 2.5A (5V DC) and 1A (12V DC).
10/100/1000Base-T port link LED is lit, but the traffic is irregular
Solution:
Check that the attached device is not set to dedicate full duplex. Some devices use a physical or software switch to
change duplex modes. Auto-negotiation may not recognize this type of full-duplex setting.
- 9 -
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A NETWORKING CONNECTION
A.1 Switch‘s RJ-45 Pin Assignments
1000Mbps, 1000Base T
Contact
MDI
MDI-X
1
2
3
4
5
6
7
8
BI_DA+
BI_DA-
BI_DB+
BI_DC+
BI_DC-
BI_DB-
BI_DD+
BI_DD-
BI_DB+
BI_DB-
BI_DA+
BI_DD+
BI_DD-
BI_DA-
BI_DC+
BI_DC-
10/100Mbps, 10/100Base-TX
RJ-45 Connector pin assignment
MDI
MDI-X
Contact
Media Dependant
Interface
Media Dependant
Interface -Cross
1
2
Tx + (transmit)
Tx - (transmit)
Rx + (receive)
Rx + (receive)
Rx - (receive)
Tx + (transmit)
3
4, 5
6
Not used
Rx - (receive)
Tx - (transmit)
7, 8
Not used
A.2 RJ-45 cable pin assignment
The standard RJ-45 receptacle/connector
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
There are 8 wires on a standard UTP/STP cable and each wire is color-coded. The following shows the pin allocation
and color of straight cable and crossover cable connection:
Figure A-1: Straight-Through and Crossover Cable
Please make sure your connected cables are with same pin assignment and color as above picture before deploying the
cables into your network.
2080-A31120-001
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|