Always there to help you
Register your product and get support at
AD7000W
Question?
Contact
Philips
User manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1 Important
2
Safety
Notice
2
3
2 Your Entertainment System
Introduction
5
5
5
5
6
6
What's in the box
What else you need
Overview of the main unit
Get started to use AirPlay
3 Prepare
7
7
7
Connect power
Turn AD7000W on
4 Connect to your homeWi-Fi
network for AirPlay
8
8
Scenario 1: Connect to a WPS router
Scenario 2: Connect to a non-WPS router 9
5 Play
15
Stream audio from your iTunes music
library to AD7000W
Control play
Use advanced sound settings
Play/charge your iPod/iPhone/iPad
through USB socket
15
17
17
17
18
Play from an external device
6
Update firmware
Download the update file
Update from the configuration page
19
19
19
7 Product information
21
21
Specifications
8 Troubleshooting
22
EN
1
Download from Www.Somanuals.com. All Manuals Search And Download.
h Do not remove the casing of this product.
1 Important
i Do not expose the product to dripping
/ splashing water, rain or high humidity.
j Keep this product away from direct
sunlight, naked flames or heat.
Safety
k Do not install near any heat
sources such as radiators, heat
registers, stoves, or other electrical
equipment (including amplifiers).
Information for Europe:
Know these safety symbols
l Do not place any other electrical
equipment on the product.
m Do not place any sources of
danger on the product (e.g. objects
containing liquids, burning candles).
n Where the mains plug or an appliance
coupler is used as the disconnect
device, the disconnect device
shall remain readily operable.
The 'exclamation mark' calls attention to
features for which you should carefully
read the supplied literature to prevent
operating and maintenance problems.
Warning
• Never remove the casing of this apparatus.
• Never lubricate any part of this apparatus.
• Never place this apparatus on other electrical
equipment.
• Keep this apparatus away from direct sunlight, naked
flames or heat.
The 'lightening bolt' symbol indicates
uninsulated components within the product
that can cause an electric shock.
To reduce the risk of fire or electric shock,
do not expose the product to rain or
moisture and do not place any objects filled
with liquids, such as vases, on the product.
• Ensure that you always have easy access to the power
cord, plug or adaptor to disconnect this apparatus from
the power.
a Read these instructions.
b Keep these instructions.
c Heed all warnings.
Risk of overheating! Never install this
apparatus in a confined space.Always
leave a space of at least four inches around
this apparatus for ventilation. Ensure
curtains or other objects never cover
the ventilation slots on this apparatus.
d Follow all instructions.
e Do not use this product near water.
f Clean only with dry cloth.
g Do not block any ventilation
openings. Install in accordance with
the manufacturer's instructions.
2
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Mains fuse
This information applies only to
products with a UK mains plug.
This product is fitted with an approved molded
plug. If you replace the fuse, use one with:
•
•
•
the ratings shown on the plug,
a BS 1362 approval, and
When this crossed-out wheeled bin
symbol is attached to a product it
means that the product is covered by
the European Directive 2002/96/EC.
the ASTA approval mark.
Contact your dealer if you are not sure
about what type of fuse to use.
Please inform yourself about the
local separate collection system for
electrical and electronic products.
Caution:To conform with the EMC
directive (2004/108/EC), do not detach
the plug from the power cord.
Please act according to your local rules and
do not dispose of your old products with
your normal household waste. Correct
disposal of your old product helps to
prevent potential negative consequences
for the environment and human health.
Notice
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy
to separate into three materials: cardboard
(box), polystyrene foam (buffer) and
Hereby,WOOX Innovations declares
that this product is in compliance with
the essential requirements and other
relevant provisions of Directive 1999/5/
EC.You can find the Declaration of
polyethylene (bags, protective foam sheet.)
Your system consists of materials which
can be recycled and reused if disassembled
by a specialized company. Please observe
the local regulations regarding the
disposal of packaging materials, exhausted
batteries and old equipment.
Any changes or modifications made to this
device that are not expressly approved by
WOOX Innovations may void the user’s
authority to operate the equipment.
Philips and the Philips’ Shield Emblem are
registered trademarks of Koninklijke Philips N.V.
and are used by WOOX Innovations Limited
under license from Koninklijke Philips N.V.”
Specifications are subject to change without
notice.WOOX reserves the right to change
products at any time without being obliged
to adjust earlier supplies accordingly.
“Made for iPod,”“Made for iPhone,” and
“Made for iPad” mean that an electronic
accessory has been designed to connect
specifically to iPod, iPhone, or iPad, respectively,
EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
and has been certified by the developer to
meet Apple performance standards.Apple
is not responsible for the operation of this
device or its compliance with safety and
regulatory standards. Please note that the
use of this accessory with iPod, iPhone, or
iPad may affect wireless performance.
AirPlay, iPod, and iPhone are trademarks of
Apple Inc., registered in the U.S. and other
countries. iPad is a trademark of Apple Inc.
Class II equipment symbol:
CLASS II apparatus with double insulation,
and no protective earth provided.
Note
• The type plate is located on the bottom of the
apparatus.
4
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Tip
2 Your
about more Philips AirPlay-enabled devices.
Entertainment
System
With AD7000W, you can also:
•
•
•
charge your iPod/iPhone/iPad through
the USB socket with an Apple USB
cable (not supplied).
Congratulations on your purchase, and
welcome to Philips!To fully benefit from
the support that Philips offers, register your
play your iTunes music library on
your iPod/iPhone/iPad through the
USB socket directly while charging.
If you contact Philips, you will be asked
for the model and serial number of
this apparatus.The model number and
serial number are on the bottom of the
apparatus.Write the numbers here:
play music from other audio devices
through the MP3-LINK socket.
What's in the box
Model No. __________________________
Serial No. ___________________________
Check and identify the contents
of your package:
•
Main unit (with a built-in Wi-Fi
module)
Introduction
•
•
•
1 x AC power adapter
1 x MP3 link cable
Printed materials
Apple AirPlay technology enables you to
play your iTunes music library, hosted on a
Mac, PC, iPhone, iPod touch, or iPad on any
AirPlay-enabled device (for example, your
AD7000W) connected to the Wi-Fi network.
What else you need
With an AirPlay-enabled device (for
example, your AD7000W), you can:
To stream audio wirelessly by AirPlay, you need:
•
•
stream audio from your iTunes music
library to any room in your house
•
•
A Wi-Fi certified router
A host for your iTunes music library,
for example, an iPod touch/iPhone/
iPad installed with iOS 4.3.3 (or
later) or a Wi-Fi enabled PC/Mac
installed with iTunes 10.2.2 (or later)
choose which AirPlay-enabled
devices you want to play music
on (if you have more than one
such devices in your house)
•
stream audio to multiple AirPlay-
enabled devices at the same
time (from the iTunes music
library on your PC/Mac only)
Your AD7000W should be connected to
the same local network as your iTunes
host device through the Wi-Fi router.
EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Connect the unit to a Wi-Fi network.
List of compatible iTunes host devices
for AirPlay
Show the Wi-Fi connection
status of the unit.
In terms of AirPlay,AD7000W
is compatible with:
e MP3-LINK
Connect an external audio player
through the supplied MP3 link cable.
f DC IN
•
•
•
a Wi-Fi enabled PC/Mac installed with
iTunes 10 (or later); and
the following iPod/iPhone/iPad models
installed with iOS 4.3 (or later):
•
Connect the power adaptor.
g USB
•
•
•
•
•
iPad 2
•
Connect an iPod/iPhone/iPad through
an Apple USB cable (not supplied).
iPad
iPhone 4
iPhone 3GS
iPod touch (2nd, 3rd, and
4th generation)
Get started to use AirPlay
To get started with AirPlay, you need to:
Overview of the main unit
1
Upgrade your iPod touch/iPhone/iPad to
the latest iOS version (iOS 4.3 or later).
a
•
Or install the latest version of iTunes
(iTunes 10 or later) on your PC/Mac.
SOURCE
L
O
V
R
WE
PO
b
c
2
3
d
Wi-Fi network (see 'Connect to your
home Wi-Fi network for AirPlay' on page
8).
e
f
4
Make sure that your iPod touch/iPhone/
iPad or PC/Mac are also connected to the
same Wi-Fi network.
h g
a Power indicator
b
•
•
Turn the unit on/off.
(Press and hold) reset the unit.
c +/-
•
Adjust volume.
d WI-FI SETUP button/indicator
6
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Prepare
Turn AD7000W on
1
2
Press on the back to turn the unit on.
Always follow the instructions in
this chapter in sequence.
Wait for successful boot-up of the unit.
» The boot-up takes about 35 seconds.
» During boot-up, the WI-FI SETUP
indicator on the back of the unit blinks
green quickly.
Connect power
» After boot-up, if no Wi-Fi connection
has been set up for AD7000W, the
WI-FI SETUP indicator starts to blink
green slowly.
Caution
• Risk of product damage! Make sure that the power
supply voltage matches the voltage printed on the
bottom of the unit.
• Risk of electric shock! When you unplug the AC
adaptor, always pull the plug from the socket. Never
pull the cord.
•
•
To switch the unit to Eco standby mode,
press .
• Before you connect the AC adaptor, make sure that you
have completed all the other connections.
To switch the unit on from Eco standby
mode, press again.
•
Connect the AC power cord to
•
the DC IN socket on the back of the
unit.
•
the wall power socket.
EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
Make sure that your Wi-Fi router is
powered on and working properly.
4 Connect to
your homeWi-
Fi network for
AirPlay
Make sure that AD7000W has been
powered on and booted up successfully.
Identify the type of your Wi-Fi router (see
the user manual of your Wi-Fi router for
details).
Scenario 1: Connect to a
WPS router
Note
• Before you press any button on AD7000W, make sure
that AD7000W has been booted up successfully.
1
Press the WPS button on your home Wi-Fi
router.
WPS
To connect AD7000W to your existing
home Wi-Fi network, you need to apply
your home Wi-Fi settings to AD7000W.
You can do this in two ways (depending
on which type of Wi-Fi router you use):
•
Connection) (see 'Scenario 1: Connect
•
does not support WPS (see
'Scenario 2: Connect to a non-
2
Shortly after step 1, press Wi-Fi SETUP on
the back of AD7000W.
» The Wi-Fi SETUP indicator blinks red,
yellow and green alternately.
» Within 2 minutes, the WI-FI SETUP
indicator stops blinking and stays green,
and the unit beeps.
Once connected successfully,AD7000W
will remember your home Wi-Fi settings.
Then you can enjoy AirPlay whenever
AD7000W is powered on and connected
to your home Wi-Fi network automatically.
» AD7000W is connected to your home
Wi-Fi network successfully.
Before connection of AD7000W to you
home Wi-Fi network, check the points below.
8
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Follow the sequence below for connection
of AD7000W to a non-WPS Wi-Fi router.
1
AD7000W Wi-Fi setup (see 'Collect
settings of your home Wi-Fi router' on
2
mode (see 'Switch AD7000W to Assisted
» A new Wi-Fi network created by
AD7000W will appear, with the
network name (SSID) of Philips Fidelio
AirPlay.
Tip
3
(see 'Connect your Wi-Fi enabled device
to the newly created Wi-Fi network' on
• For some Wi-Fi routers, you may need to hold the
WPS button for Wi-Fi connection or enable the WPS
PBC function from the router configuration pages. See
the user manuals of the specific routers for details.
• If the Wi-Fi SETUP indicator on AD7000W blinks
yellow, it means that the Wi-Fi connection has failed.
Please wait for 2 minutes and try again. If the problem
(see 'Scenario 2: Connect to a non-WPS router' on
4
5
enabled device (see 'Open the built-in web
• If the Wi-Fi connection fails again, press and hold on
the back of AD7000W to reset it, and then try again.
wrote on paper at step 1 (see 'Change the
internal Wi-Fi settings of AD7000W' on
Scenario 2: Connect to a
non-WPS router
6
'Restore your Wi-Fi enabled device back
to your existing home Wi-Fi setting' on
Note
• You can also follow the procedures below to connect
AD7000W to a WPS router manually.
To connect AD7000W to a Wi-Fi router
manually, you need access to AD7000W's
built-in configuration web page for change of
its internal Wi-Fi settings.To do so, you need a
Wi-Fi enabled device with an Internet browser
for temporary Wi-Fi connection to AD7000W.
The Wi-Fi enabled device can be an iPod touch/
iPhone/iPad or a Wi-Fi enabled PC/Mac.
EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Collect settings of your homeWi-Fi
router
Note
• Always consult the user manual of your home Wi-Fi
router for detailed instructions.
1
2
Connect your Wi-Fi enabled device to
your existing home Wi-Fi network.
Launch the Internet browser (for example,
Apple Safari or Microsoft Internet
Explorer) on your Wi-Fi enabled device.
•
Press and hold Wi-Fi SETUP on the back
of AD7000W for more than 5 seconds.
» The Wi-Fi SETUP indicator blinks
green and yellow alternately.
» A new Wi-Fi network created by
AD7000W will appear, with the
network name (SSID) of Philips Fidelio
AirPlay.
3
4
Open the configuration page of your
home Wi-Fi router.
Find the Wi-Fi settings tab and write down
the following information on paper:
A Network name (SSID)
B Wi-Fi security mode (usually WEP,
WPA or WPA2 if enabled)
C Wi-Fi password (if Wi-Fi security is
» It may take up to 45 seconds for
successful creation of this new Wi-Fi
network.
enabled)
D DHCP mode (enabled or disabled)
E Static IP address settings (if DHCP
Note
mode is disabled)
• After you finish manual Wi-Fi setup for AD7000W,
the new Wi-Fi network created by AD7000W will
disappear.
Switch AD7000W to AssistedWi-Fi
Setup mode
• If you fail to enter Assisted Wi-Fi Setup mode, power
off AD7000W and power on it, then try again after
successful boot-up.
Note
• Make sure that there are no other Philips AirPlay-
enabled devices in Assisted Wi-Fi Setup mode at the
same time. Multiple Wi-Fi networks created this way
may interfere with each other.
• Before you press any button on AD7000W, make sure
that AD7000W has been booted up successfully.
10 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect yourWi-Fi enabled device to
the newly createdWi-Fi network
The new Wi-Fi network created by
AD7000W only allows access of one Wi-
Fi enabled device.To avoid interference
from any other Wi-Fi devices, you are
recommended to temporarily disable the
Wi-Fi function on your other Wi-Fi devices.
Philips Fidelio AirPlay
Option 1: Use your iPod touch/iPhone/iPad
1
Select Settings -> Wi-Fi on your iPod
touch/iPhone/iPad.
3
Wait until successful Wi-Fi connection on
your iPod touch/iPhone/iPad.
»
is displayed at the upper left corner
of your iPod touch/iPhone/iPad.
Tip
• If Philips Fidelio AirPlay is not in the list, try to scan the
available Wi-Fi networks again.
Option 2: Use yourWi-Fi enabled PC/Mac
Note
• See the user manual of your PC/Mac for how to
connect your PC/Mac to a Wi-Fi network.
2
Select Philips Fidelio AirPlay from the list
of available networks.
• During Wi-Fi network connection, do not connect any
network cable to your PC/Mac.
1
Open the Wi-Fi setup tool or control
panel on your PC/Mac.
EN 11
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Scan the available Wi-Fi networks.
Tip
• If Philips Fidelio AirPlay is not in the list, try to scan the
available Wi-Fi networks again.
Open the built-in web page of
AD7000W
1
Launch Apple Safari browser or any other
Internet browser on your Wi-Fi enabled
device.
2
Type in 192.168.1.1 at the browser
address bar and confirm.
3
Select Philips Fidelio AirPlay from the list
of available networks.
» The AD7000W configuration web
page is displayed.
192.168.1.1
4
Wait until successful Wi-Fi connection on
your PC/Mac.
If you use Safari on yourWi-Fi enabled PC/
Mac, you can also select 'Philips_Fidelio XXX'
from the Bonjour pull-down list to enter the
AD7000W configuration web page directly.
12 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Click -> Preferences.
» The Bookmarks menu is displayed.
Change the internalWi-Fi settings of
AD7000W
On the AD7000W configuration web page,
you can change the internal Wi-Fi settings
of AD7000W for connection of AD7000W
to your existing home Wi-Fi network.
Note
• Make sure that the settings on the configuration web
page match your home Wi-Fi network settings that you
wrote on paper.
2
3
Tick Include Bonjour for Bookmarks bar.
Select 'Philips_Fidelio XXX' from the
Bonjour pull-down list shown at the
bookmarks bar.
» The AD7000W configuration web
page is displayed.
•
Follow the on-screen instructions to
change and confirm the internal Wi-Fi
settings of AD7000W.
» After a while, the indicator on the back
of AD7000W stops blinking and stays
green, and the unit beeps.
» AD7000W is connected to your
existing home Wi-Fi network
successfully.
EN 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
• If the WI-FI SETUP indicator on AD7000W does not
stay green steadily, it means that the Wi-Fi connection
has failed. Please power off both your Wi-Fi router
and AD7000W and then power on them again to see
whether AD7000W can be connected to your home
Wi-Fi network. If the problem remains, try the above
procedures again.
• After you finish the above changes or power-off and
power-on of AD7000W, the new Wi-Fi network
created by AD7000W will disappear.
Tip
• If you like, you can change the name of your AD7000W
in Advanced settings -> AirPlay Device Name on the
AD7000W configuration web page.This is helpful when
you have multiple Philips AirPlay-enabled devices in
your house and you need to distinguish between them.
• If you want to enter the network name (SSID) manually
(for example, if you want to hide your SSID), go to
Advanced settings -> CONFIGURE MANUALLY on
the AD7000W configuration web page.
2
Select your network name (SSID) from the
list of available wireless networks.
Restore yourWi-Fi enabled device
back to your existing homeWi-Fi
setting
Note
• Make sure that the settings at steps 2 to 3 below match
your home Wi-Fi network settings you wrote on paper.
1
Select Settings ->Wi-Fi on your iPod
touch/iPhone/iPad.
•
Or open the list of available Wi-Fi
networks on your PC/Mac.
3
4
Enter the network key if required.
Wait until successful Wi-Fi connection to
your home Wi-Fi network.
14 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Play
Stream audio from your
iTunes music library to
AD7000W
Note
• Make sure that your iTunes host device is connected
to the same Wi-Fi network as AD7000W.Your iTunes
device can be an iPod touch/iPhone/iPad installed with
iOS 4.3 (or later) or a Wi-Fi enabled PC/Mac installed
with iTunes 10 (or later).
• For iPhone 4S users:To ensure optimal performance
of AirPlay streaming, upgrade your iPhone 4S to iOS
5.1 or later.
Stream from your iPod touch/iPhone/
iPad
3
Select Philips_Fidelio XXXX (or user
customized name) from the AirPlay list.
1
2
Launch the iPod/Music application on your
iPod touch/iPhone/iPad.
Tap on the AirPlay icon.
EN 15
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Select a media file and start play.
» After a while, you will hear music from
AD7000W.
3
Select Philips_Fidelio_AirPlay XXXX (or
user customized name) from the AirPlay
list.
4
Select a media file and start play.
» After a while, you will hear music from
AD7000W.
Note
• If you fail to hear music after successful setup, do one of
the following on your iPod touch/iPhone/iPad:
• (1) Disconnect and then re-connect to the same Wi-Fi
router again;
• (2) Close all applications running at the background;
• (3) Power off and then power on your iPod touch/
iPhone/iPad again.
Stream from your PC/Mac
1
2
Launch iTunes 10.2.2 (or a later version)
on your PC/Mac.
Click the AirPlay icon on the window.
16 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
If your iTunes host device is a
Wi-Fi enabled PC/Mac:
Tip
• When you stream audio from your iTunes music library
on a PC/Mac, you can select more than one AirPlay-
enabled devices (if available) at step 3 to stream music
to all of them at the same time.
• If you are using an earlier version of iTunes, the AirPlay
icon may be instead of
For advanced sound settings, you can
use the equalizer available on iTunes
directly (View -> Show Equalizer).
.
Tip
• See the iTunes help documentation for more details.
Control play
You can select different play options from
either your iTunes host device or AD7000W.
Play/charge your iPod/iPhone/
iPad through USB socket
Note
Note
• The USB socket is only compatible with iPod/iPhone/
iPad.
• Make sure that you have successfully streamed audio
from your iTunes music library to AD7000W.
•
•
To pause or resume play, press
.
You can play or charge your iPod/iPhone/
iPad through the USB socket with an
Apple USB cable (not supplied).
To adjust volume, press +/- repeatedly.
If you have stopped audio streaming by AirPlay,
after successful USB connection, the unit
switches to the USB source automatically.
Tip
• If you are streaming music from a PC/Mac, to control
music play from AD7000W, launch iTunes and tick
Allow iTunes audio control from remote speakers
in Edit (for Windows) or iTunes (for Mac) ->
Preferences... -> Devices.
,
Use advanced sound settings
If your iTunes host device is an
iPod touch/iPhone/iPad:
For advanced sound settings and additional
features, you can use your iPod touch/
iPhone/iPad to download the Philips
SoundStudio application from Apple App
Store. It is a free application from Philips.
•
Connect an Apple USB cable (not
supplied) to:
EN 17
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
the USB socket on the back of
AD7000W.
the dock connector on
your iPod/iPhone/iPad.
Compatible iPod/iPhone/iPad
The USB socket supports play and charge of
the following iPod, iPhone, and iPad models.
•
•
•
•
•
•
•
•
•
•
iPad 2
iPad
iPhone 4
iPhone 3GS
iPhone 3G
iPhone
iPod classic
iPod 5G
iPod 4G
1
Connect the supplied MP3 link cable to:
•
the MP3-LINK socket on the back of
the unit.
iPod nano (2nd, 3rd, 4th, 5th, and 6th
generation)
•
the headphone socket on an
external audio player.
•
iPod touch (1st, 2nd, 3rd, and 4th
generation)
2
3
Press the MP3-LINK button on the back of
the unit to switch to the MP3 link source.
Start music play on the external audio
player.
Play from an external device
You can also listen to an external
audio player through the unit.
Tip
• To switch back to the AirPlay or USB play mode, you
just need to select a song on the connected iPod/
iPhone/iPad and start play again.
18 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Update
firmware
Update from the
configuration page
Warning
• Always connect your AD7000W to AC power for
firmware upgrade. Never power off your AD7000W
during firmware upgrade.
Note
• You can only update the firmware from a PC/Mac.
Note
• To use an Internet browser other than Apple Safari
on your PC/Mac, remember to go to the Wi-Fi router
configuration page and write down the IP address of
your AD7000W. See the user manual of your Wi-Fi
router for how to find the IP addresses of devices
connected to the Wi-Fi router.
Download the update file
1
Power on AD7000W.
» It takes about 35 seconds for the unit
to boot up. During boot-up, the WI-FI
SETUP indicator on the back of the
unit blinks green quickly.
XXXX
» After boot-up, you can hear a beep
and the WI-FI SETUP indicator
turns to green steadily.AD7000W is
connected to the last configured Wi-Fi
network automatically.
XXXX. zip
2
3
Make sure that AD7000W and your PC/
Mac are connected to the same Wi-Fi
router.
1
2
3
support.
Open Apple Safari on your PC/Mac, then
select 'Philips_Fidelio XXX' from the
Bonjour pull-down list.
Enter the model number to find the latest
firmware upgrade file available.
Save and unzip the upgrade file to your
hard drive.
•
Or open any other Internet browser
on your PC/Mac, then type in the IP
address of AD7000W (available on the
Wi-Fi router configuration page) at the
address bar.
» The AD7000W configuration web
page is displayed.
EN 19
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Follow the on-screen instructions to
complete the firmware update.
Note
• In case the firmware update fails, you can try the above
procedures again.
• After successful firmware update, if there is any
problem with the Wi-Fi connection, press and hold
on AD7000W for more than 5 seconds to reset the
device, and then try to set up the Wi-Fi network for
AD7000W again (see 'Connect to your home Wi-Fi
20 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
General information
AC power
7 Product
information
Input: 100 - 240
V~, 50/60 Hz
1A/1.2 A
Output: 12
Note
V
3.0 A
Operation Power
Consumption
25 W
• Product information is subject to change without prior
notice.
Power Consumption
in Standby Mode
< 0.5 W
Dimensions
Specifications
- Main Unit (L x W x H) 298 x 98 x
168 mm
Weight
Amplifier
Rated Output Power
Frequency Response
- With Packing
- Main Unit
2.02 kg
1.36 kg
2 X 5 W RMS
63 Hz - 18
kHz, ±3 dB
Signal to Noise Ratio
> 90 dB
MP3 Link
600 mV RMS
20 kohm
Speakers
Speaker Impedance
Speaker Driver
Sensitivity
8 ohm
66 mm full range
82 dB/m/W
Wireless
Wireless
standard
Wireless
security
802.11b/g
WEP (64 or 128 bit),
WPA/WPA2 (8-63 characters)
Frequency
range
2412 - 2462 MHz (CH1-
CH11) (for /79, /37, /55, /97)
2412 - 2472 MHz (CH1-
CH13) (for /12, /10, /05)
PBC (one
Yes
button push)
EN 21
Download from Www.Somanuals.com. All Manuals Search And Download.
is only compatible with Wi-Fi
802.11b/g certified routers.
8 Troubleshooting
•
If your Wi-Fi router is Wi-Fi 802.11n
certified, make sure to enable the
802.11b/g mode.AD7000W does not
support connection to routers with
802.11n only.
Warning
• Never remove the casing of this apparatus.
•
•
This device does not support the WPS-
PIN method.
To keep the warranty valid, never try
to repair the system yourself.
If your Wi-Fi router supports WPS and the
WPS-PBC method but fails to connect to
method (see 'Scenario 2: Connect to a
Enable SSID broadcast on the Wi-Fi router.
Keep away from potential sources of
interference which may affect Wi-Fi signal,
such as microwave ovens.
If you fail to use your PC for Wi-Fi network
setup, check whether your PC is using a
Wi-Fi network.You cannot use Ethernet
connection for AirPlay network setup.
Make sure that the SSID name of your
home router consists of alphanumeric
characters, with no space or special
characters like %/#/* inserted.
If you choose to rename the AirPlay device
'Philips_Fidelio XXXX' in the setting
menu, do not use special characters or
symbols.
If you encounter problems when using this
apparatus, check the following points before
requesting service. If the problem remains
unsolved, go to the Philips web site (www.
philips.com/welcome).When you contact Philips,
ensure that the apparatus is nearby and the
model number and serial number are available.
•
•
No power
•
•
•
•
•
Make sure that the AC power plug of
the device is connected properly.
Make sure that there is power at the AC
outlet.
•
No sound
•
•
Adjust the volume.
Check the Wi-Fi network connection.
'Connect to your home Wi-Fi network for
For some new types of Wi-Fi routers, a
network name (SSID) may be created
automatically when you use WPS for
connection.Always change the default
network name (SSID) to a simple one that
consists of alphanumerical characters, and
also change the Wi-Fi security mode to
secure your network.
No response from the unit
•
Press and hold on AD7000W for more
than 5 seconds to reset the device.Then
again (see 'Connect to your home
Disconnect and reconnect the AC power
plug, and then switch on the device again.
•
Occasional breaking of AirPlay music
streaming
Do one or all of the following:
Wi-Fi network connection failed
•
Move AD7000W closer to
your Wi-Fi router.
•
Check if your Wi-Fi router is Wi-
Fi 802.11b/g certified.This device
22 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
Remove any obstacles between AD7000W
and your Wi-Fi router.
Avoid using Wi-Fi channel which is
overlapped by the nearby Wi-Fi network.
Check if your network speed is fast enough
(in cases where multiple devices share the
same router, the AirPlay performance may
be affected).Turn off the other devices
connected to your home router.
•
•
Enable the Quality of Service (QoS)
option (if available on the Wi-Fi router).
Turn off other Wi-Fi routers.
No AirPlay icon on my iTunes host device
•
Make sure that AD7000W is already
connected to your home Wi-Fi network.
Before you open iTunes, make sure that
you have enabled Bonjour service in
your PC.Take Windows XP for example:
to enable the service, you can click
Start->Control Panel, and double-click
AdministrativeTools-> Services->Bonjour
Service, then click Start followed by OK
on the pop-up menu.
•
•
If the problem remains, try to restart
AD7000W.
AirPlay connection failed with Mac or PC
•
Temporarily disable the firewall and
security software to see whether it blocks
the ports that AirPlay uses to stream
content. See the help documentation of
your firewall and security software on how
to unblock the ports used by AirPlay.
When you use iPodTouch/iPhone/iPad/
Mac/PC for AirPlay, if the music play breaks
or stops, try to restart your iPodTouch/
iPhone/iPad, iTunes or AD7000W.
Video streaming or FTP downloads may
overload your router and therefore may
cause interruptions during AirPlay music
play.Try to reduce the load of your router.
•
•
EN 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications are subject to change without notice.
2013 ©WOOX Innovations Limited.All rights reserved.
This product was brought to the market by WOOX Innovations
Limited or one of its affiliates, further referred to in this document
as WOOX Innovations, and is the manufacturer of the product.
WOOX Innovations is the warrantor in relation to the product
with which this booklet was packaged. Philips and the Philips Shield
Emblem are registered trademarks of Koninklijke Philips N.V.
AD7000W_10/12_UM_V2.0
Download from Www.Somanuals.com. All Manuals Search And Download.
|