Philips Laptop 7FF1WD User Manual

Philips Photo Frame  
Update Procedure Document  
Firmware A1.51  
Release date: Jul 13, 2006  
Reason for software update: For 7FF1WD models  
Software version A1.51 will provide the following improvements:  
- Extend the SD card support from 1GB to 2GB  
- Increasing maximum photos support number from 4096 to 10240  
Important notice before updating:  
The software update process will remove all photos currently stored on Photo Frame. Please make  
sure all photos on Photo Frame are properly backed up before updating.  
What is needed before software update  
1. Check your current Photo Frame software version.  
> Make sure Photo Frame is ON> Press the 3rd key from the left on the rear of Photo Frame >  
General settings menu will appear. > Use the key behind the Down arrow to highlight Status. >  
Current Software version will appear on the right column. > If the software version is earlier than  
1.51, this update is applicable to your Photo Frame.  
2.  
3.  
Prepare a supported memory card: If your software version is 1.47 or earlier than 1.31, only  
Secure Digital (SD) type of memory card can be supported during software update. All other  
versions support Secure Digital (SD), Memory Stick (MS), Compact Flash (CF), or Multimedia  
Card (MMC) types of memory cards.  
PC with Internet access or downloaded Photo Frame software on PC  
Software update procedure  
1.  
After downloading, Unzip all the software file, and select correct software update ZIP file  
Software version 1.47 or earlier than 1.31  
WD_VA1.51_SD.zip  
Software version later that 1.31 but not 1.47  
WD_VA1.51_AllTypeCard.zip  
7FFEWD  
2.  
3.  
Unzip all the software update files (6 files in total) onto the root directory of the supported memory card  
Make sure Photo Frame is OFF and properly connected to DC power.  
Important: Please use DC power NOT battery power to avoid a possible power loss that could  
cause permanent damage to your Photo Frame.  
4.  
5.  
Insert the supported memory card into Photo Frame  
Power on Photo Frame; the software update will start automatically. During the update, DO NOT  
remove the memory card or make new connections.  
Note: It may take up to 1 minute before the updating process begin. The screen will remain  
black during this period  
4.  
The Software update is complete when you see one of the following messages on Photo Frame:  
Photos stored on your memory card  
Or if you memory card does not contain photos:  
No photos on external memory  
6.  
7.  
8.  
After software update is complete, remove the memory card.  
Restart Photo Frame  
Congratulations! You have successfully updated your Photo Frame. You may remove the  
software update files from the memory card now.  
Troubleshooting:  
In the event your software update is not successful, please make sure:  
1. Your memory card is supported by current software  
2. All files are correctly unzipped to the root directory of the supported memory card.  
Note: If you have previously updated another Photo Frame with this memory card, some files may have  
been changed by the update. Solution: Unzip the files again from the PC to the supported  
memory card.  
3. Make sure Photo Frame is properly powered during the entire update process.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pelco Car Video System PMCL500 User Manual
Philips Automobile Accessories 32PFL8404H User Manual
Philips Coffeemaker HD8743 User Manual
Philips Cordless Telephone CD2352S User Manual
Philips DVD Player DVD 612 User Manual
Philips Flat Panel Television 15MF400T User Manual
Pioneer Network Card DVR 216D User Manual
Poulan Tiller PRRT65 User Manual
ProForm Fitness Electronics PCTL120090 User Manual
PSB Speakers Portable Speaker Loudspeakers User Manual