E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 1
DIGITAL VIDEO DISC PLAYER &
DVP3345V
VIDEO CASSETTE RECORDER
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 3
Safety Information 3
IMPORTANT SAFETY INSTRUCTIONS
Read before operating equipment
●
1. Read these instructions.
Do not compromise these design standards by applying excessive pull
force to the front, or top, of the cabinet which could ultimately overturn
the product.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
●
Also, do not endanger yourself, or children, by placing electronic
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with
the manufacturers instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or groundingtype
plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has
two blades and third grounding prong. The wide
equipment/toys on the top of the cabinet. Such items could unsuspect-
ingly fall from the top of the set and cause product damage and/or per-
sonal injury.
18. Wall or Ceiling Mounting - The appliance should be mounted to a
wall or ceiling only as recommended by the manufacturer.
19. Power Lines - An outdoor antenna should be located away from power
lines.
20. OutdoorAntenna Grounding - If an outside antenna is connected to
the receiver, be sure the antenna system is grounded so as to provide
some protection against voltage surges and built up static charges.
Section 810 of the National Electric Code, ANSI/NFPA No. 70- 1984,
provides information with respect to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna dis-
charge unit, size of grounding connectors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements for the
grounding electrode. See Figure below.
AC Polarized
blade or third prong are provided for your safety.
Plug
When the provided plug does not fit into your out-
let, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
21. Object and Liquid Entry - Care should be taken so that objects do not
fall and liquids are not spilled into the enclosure through openings.
a) Warning: To reduce the risk of fire or electric shock, this apparatus
should not be exposed to rain or moisture and objects filled with liq-
uids, such as vases, should not be placed on this apparatus.
22. Battery Usage CAUTION - To prevent battery leakage that may result
in bodily injury, property damage, or damage to the unit:
12.
Use only with a cart, stand, tripod, bracket, or table specified
by the manufacturer, or sold with the apparatus. When a cart
is used, use caution when moving the cart/apparatus combina-
tion to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
●
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-sup-
ply cord or plug is damaged, liquid has been spilled or objects have fall-
en into apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
15. This product may contain lead and mercury. Disposal of these materials
may be regulated due to environmental considerations. For disposal or
recycling information, please contact your local authorities or the
Install all batteries correctly, with + and - aligned as marked on the
unit.
●
Do not mix batteries (old and new or carbon and alkaline, etc.).
●
Remove batteries when the unit is not used for a long time.
23. Overloading - Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or electric
shock.
24. Object and Liquid Entry - Never push objects of any kind into this
product through openings as they may touch dangerous voltage points
or short-out parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
16. Damage Requiring Service - The appliance should be serviced by
qualified service personnel when:
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a
marked change in performance; or
25. Replacement Parts - When replacement parts are required, be sure the
service technician has used replacement parts specified by the manufac-
turer or have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other hazards.
26. Safety Check - Upon completion of any service or repairs to this prod-
uct, ask the service technician to perform safety checks to determine
that the product is in proper operating condition.
E. The appliance has been dropped, or the enclosure damaged.
17. Tilt/Stability - All televisions must comply with recommended interna-
tional global safety standards for tilt and stability properties of its cabi-
net design.
Note to the CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC
that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
Example of Antenna Grounding
as per NEC - National Electric Code
GROUND CLAMP
ANTENNA LEAD IN WIRE
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
GROUNDING CONDUCTORS (NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)
ELECTRIC SERVICE EQUIPMENT
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 4
4 Safety Information (cont’d)
Safety Precautions
Warning: To prevent fire or shock hazard, do not expose this equipment to rain or moisture.
Federal Communications Commission (FCC) Warning: Any unauthorized changes or
modifications to this device void the user’s authority to operate it.
• Do not stand the unit up vertically. Install the unit in a horizontal and stable position.
• Be sure to remove the disc and unplug the AC power cord from the outlet before carrying the unit.
Department of Health and Human Services (DHHS) Certification: Complies with 21 Center
for Radiation (CFR) chapter 1 subchapter J applicable at time of manufacture.
Laser Safety: This unit employs a laser. Only a qualified service person should remove the cover
or attempt to service this device, due to possible eye injury.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK
DEFEATED. DO NOT STARE INTO BEAM. THE BEAM IS LOCATED INSIDE, NEAR THE DECK
MECHANISM.
Special Information for Canadian Users: This Class B digital apparatus complies with
Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Radio/TV Interference: This device has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide
reasonable protection against harmful interference in a residential installation.This device generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device
does cause harmful interference to radio or television reception, which can be determined by turning the
device off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the device and the receiver.
3) Connect the device into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
Copyright Notice: The making of unauthorized copies of copy-protected material, including
computer programs, files, broadcasts and sound recordings, may be an infringement of copyrights and
constitute a criminal offence. This equipment should not be used for such purposes.
Copyright Protection: Unauthorized copying, broadcasting, public performance, and lending of
Discs are prohibited.
This product incorporates copyright protection technology that is protected by U.S. patents and
other intellectual property rights. Use of this copyright protection technology must be authorized by
Macrovision, and is intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision. Reverse engineering or disassembly is prohibited.
Notice for Progressive Scan Use: Consumers should note that not all high definition
television sets are fully compatible with this product and may cause artifacts to be displayed in the
picture. In case of picture problems with 525 (480) progressive scan output, it is recommended that the
user switch the connection to the ‘standard definition’ output. If there are questions regarding your TV
set compatibility with this 525p (480p) DVD player, please contact our customer service center.
Declaration of Conformity
Model Number:
Trade Name:
Responsible Party:
DVP3345V
Philips
P&F USA, Inc.
P.O. Box 672768 Marietta, Georgia 30006
1-866-771-4018
Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of Dolby
Laboratories.
Copyright 2009 Philips. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 5
Table of Contents 5
General Information
AdditionalVCR Features
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . .3-4 Hi-Fi Stereo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Playable Discs andVideo Cassettes . . . . . . . . . . . . . .7 Disc Playback Features
Menus, Playback Control (PBC) Function . . . . . . . .32
Fast Forward/Fast Reverse . . . . . . . . . . . . . . . . . . .33
x1.3 and x0.8 Rapid Play withVoice . . . . . . . . . . . . .33
Hookups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-12 Title/Chapter/Time Search . . . . . . . . . . . . . . . . . . .34
Remote Control Setup . . . . . . . . . . . . . . . . . . . . . .13 Track Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
First-time DVD/VCR Setup . . . . . . . . . . . . . . . . . . .14 Paused and Step-by-Step Playback, Resume On . . .36
Repeat, A-B Repeat . . . . . . . . . . . . . . . . . . . . . . . . .37
Initial DVD/VCR Setup
Markers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Subtitles, Camera Angles . . . . . . . . . . . . . . . . . . . . .39
Basic Playback
Video Cassette Playback . . . . . . . . . . . . . . . . . . . . .15 Audio Language, Stereo Sound Mode . . . . . . . . . . .40
Disc Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Slow Motion, Zoom . . . . . . . . . . . . . . . . . . . . . . . .41
Program /Random Playback . . . . . . . . . . . . . . . . . . .42
TM
MP3/Windows Media Audio/JPEG Playback . . .43-44
Basic DVD/VCR Controls
On-Screen Displays . . . . . . . . . . . . . . . . . . . . . .45-46
Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Black Level,Virtual Surround . . . . . . . . . . . . . . . . . .47
Front Panel, Rear Panel and Remote Control . . . . .18 Initializing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
AdditionalVCR Setup
DVD Player Setup Options
Clock (VCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48-49
Language (VCR) . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50-51
VCR Status Displays . . . . . . . . . . . . . . . . . . . . . . . .20 Progressive Scan . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Parental Password . . . . . . . . . . . . . . . . . . . . . . . . . .53
Parental Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Videotape Recording . . . . . . . . . . . . . . . . . . . . . . . .21 Others . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55-56
One-Touch Recording . . . . . . . . . . . . . . . . . . . . . . .22
VCR Recording Options
Rerecording (Tape Duplication) . . . . . . . . . . . . . . . .23
Timer Recording . . . . . . . . . . . . . . . . . . . . . . . .24-25 InformationYou May Need
Satellite Link . . . . . . . . . . . . . . . . . . . . . . . . . . . .26-27 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
DVD toVideotape Duplication . . . . . . . . . . . . . . . .28 Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . .58-60
Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . .61
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61
LimitedWarranty . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 Information Index . . . . . . . . . . . . . . . . . . . . . . . . . .63
Tape Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Video Cassette Playing Options
Time Search, Index Search . . . . . . . . . . . . . . . . . . . .30
Special Effects Playback . . . . . . . . . . . . . . . . . . . . . .31
Automatic Operation Features . . . . . . . . . . . . . . . .31
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 6
6 Introduction
Welcome!
This DVD/VCR combines a DigitalVideo Disc (DVD) player and a Hi-FiVideo Cassette
Recorder (VCR) into one unit, letting you play DVDs, Audio Compact Discs (Audio
CDs), andVideo Cassettes on one piece of equipment.
Read this owner’s manual carefully to learn how to use the features listed below.
VCR Features
• Automatic Head Cleaner
• English, French and Spanish Menus and
Displays
• Satellite Link
• Searching:Time, Index, Forward and
Reverse
• 19 Micron head
• Recording: One-Touch andTimer
• Repeat Playback
• Slow Motion
• Still Picture
• Tape Counter
• Tracking Adjustment
Disc Features
• Audio Language choices * • Windows Media Audio
• Camera Angles *
• DVD menus in a desired • Dual Playback
language *
• Markers
• MP3 Playback
• JPEG Playback
TM
• Random Playback
• Repeat, A-B Repeat
• Resume On
• Specific Time/Title/
Chapter/Track Search
• Subtitles *
Playback
• Parental Control *
• Paused/Fast/Slow/
Step-by-Step Playback
• Program Playback
• Progressive Scan
• Zoom
* If available on the disc
Package Contents
The following items are provided with your new DVD/VCR.
• Remote Control and two AA batteries
• One set of Audio (red and white tips) andVideo (yellow tips) cables
• This Owner’s Manual and Quick Start Guide
DVD Disc Menus...
Some explanations in this manual describe DVD Disc Menus. DVD manufacturers set
the menus, which vary among DVDs. Not all DVDs have menus. If the DVD has a
menu, access it by pressing DVD, then DISC MENU on the remote control.
Details are on page 32.
DVD Player Setup Menu...
Some instructions explain how to use the DVD player’s Setup Menu to set up features
of the DVD player or a DVD. Access the DVD player menu by pressing SETUP on the
remote control when playback is stopped. Even if a feature is set in the DVD player’s
menu, it may not be available if the current DVD does not include that feature.
Available Disc Features...
All features described in this manual are not available on every disc. If the feature is
not available on the disc, you cannot use the DVD/VCR to make it
available. An “X” will appear in the top right corner of the TV screen if
you try to access a feature that is not currently available.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.2.2 5:14 PM Page 7
Playable Discs and Video Cassettes 7
Playable Discs
The DVD player will play DigitalVideo Discs (DVDs); finalized DigitalVideo Discs Recordable (DVD+R, DVD-R);
finalized DigitalVideo Discs Rewritable (DVD+RW, DVD-RW);Video Compact Discs (VCDs);Audio Compact
Discs (CDs); finalized Compact Discs Recordable (CD-R) and Compact Discs Rewritable (CD-RW).
To play a DVD, make sure it meets the requirements for Region Codes and Color Systems as described
below. Discs that have the following logos will play on the DVD player. Other disc types are not guaranteed
to play in the DVD/VCR.
• Do not stand the unit up vertically. Install the unit in a horizontal and stable position.
• Be sure to remove the disc and unplug the AC power cord from the outlet before carrying the unit.
DVD+R DVD+RW DVD-R DVD-RW Video Audio
CD-R
DVD
CD-RW
MP3
files
CD
CD
Manufactured under license from Dolby Laboratories.“Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
is a trademark of DVD Format/Logo Licensing Corporation.
Windows Media is a trademark of Microsoft Corporation.
This unit is not compatible with Multiple Bit Rate
(MBR:a file that contains the same content encoded at several different bit rates).
ABOUTTHE PBC FUNCTION OFVIDEO CD
This unit can playVideo CD 1.1 (without PBC) and 2.0 (with PBC).
With version 2.0 (with PBC), you can use interactive menu (e.g., playlists) on the TV screen.
When playing aVideo CD with PBC, some operations cannot be performed unless the PBC function is
cancelled temporarily. See page 32 for more details.
Region Codes
DVDs must be labeled for ALL regions or for Region 1 in order to play on this DVD player. You cannot play
DVDs that are labeled for other regions.
Look for the symbols below on your DVDs. If these region symbols do not appear on your DVD, you
cannot play the DVD in this player.
The number inside the globe refers to a region of the world. Region 1 represents the
United States, Canada, upper regions of North America, Bermuda, the U.S.Virgin
Islands, and small regions near Australia.
A disc encoded in a specific region format can only play on DVD players with the same region code. For
example, if a disc is labeled for Region 2, you cannot play the DVD on this player.
Color Systems
Different color systems are available throughout the world. The most common color systems are NTSC,
which is used primarily in the United States and North America, PAL, and SECAM.
This DVD player will play both NTSC and PAL DVDs. You cannot play DVDs recorded in other formats.
The color system of the DVD may be listed on the DVD or on the disc case. Your TV must have the NTSC
and/or PAL color system as well.
PlayableVideo Cassettes
TheVCR of this DVD/VCR has a High Quality (HQ) system and is compatible with existingVideo Home
System (VHS) equipment. Use only video cassettes that have the
mark. The use of other tapes may
result in poor picture quality and excessive deposits on the video heads, which may not be covered by the
warranty if damage occurs.
TheVCR also has a 19 micron head, which provides a better picture when you view tapes recorded in slow
speed (SLP).
Unacceptable Discs
If you insert an unacceptable type of disc, a Disc Error message may appear on the TV screen. The following
discs will not play on this DVD player.
• CD-ROM
• Compact Disc-Interactive (CD-I) • DVD-RAM
• DVD-ROM • DVD-Audio
• DVD contains MP3, Windows Media Audio or JPEG files
• Video Single Disc (VSD)
• Unfinalized disc
TM
• Non-compatible recording mode
On the following disc, the sound may not be heard.
• Super Audio CD - Only the sound on the CD layer can be heard. The sound on the high-density Super
Audio CD layer cannot be heard.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 8
8 Hookups
Determining the best possible connection...
Your hookup will be determined primarily by your existing equipment, especially yourTV. These guidelines describe
which options have the best picture and sound quality.You will not use all the jacks on the DVD/VCR.
★★★★ If yourTV has ComponentVideo In jacks (which could be labeledY CR CB,Y PR PB orYUV and may be
green, blue and red), use the ComponentVideo jacks (Y CB/PB CR/PR) for the best picture quality. If you use
only this video connection, only the DVD picture will be available. To see DVD features on theTV, set theTV
to its ComponentVideo In channel. ComponentVideo provides the best picture quality. See page 10.
Progressive Scan provides less flickering and higher image resolution than traditional (525i/480i or interlace)
TV signals.
If yourTV has Progressive Scan (525p/480p or progressive), connect theTV to the DVD/VCR’s
COMPONENTVIDEO OUT (Y CB/PB
DVD/VCR’s DISPLAY Menu. See pages 50-5
Progressive Scan also
CR/PR) jacks. Set Progressive Scan (PROG. SCAN) to ON in the
1
. P.SCAN will appear on the DVD/VCR’s display panel. Set yourTV to
.
If yourTV does not have Progressive Scan but has ComponentVideo In jacks, connect them to
the DVD/VCR’s COMPONENTVIDEO OUT jacks (Y CB/PB CR/PR). Set Progressive Scan (PROG. SCAN) to
OFF either in the DISPLAY Menu or by pressing and holding PLAY B (DVD) on the front of the DVD/VCR
for more than 5 seconds. See pages 50-51.
★★★ If yourTV has an S-Video In jack (which also may be labeledY/C or S-VHS), use the S-VIDEO OUT jack for
excellent picture quality. If you use only this video connection, only the DVD picture will be available. To see
DVD features on theTV, set theTV to its S-Video In channel. See page 10.
★★
If yourTV has a single yellowVideo In jack (which also may be labeled CVBS, Composite or baseband), use
the yellow DVD/VCRVIDEO OUT jack for good picture quality. This connection provides a picture for both
the DVD player and theVCR. To see DVD orVCR features on theTV, set theTV to itsVideo In channel. See
page 9
★★★★ If you have a Stereo with a Coaxial Digital Audio In jack, this provides the clearest sound for the DVD player.
Connect the DVD/VCR’s COAXIAL DIGITAL AUDIO OUT jack to your Stereo for the best sound quality. If
you use only this audio connection, only disc sound (noVCR) will be available. See page 12.
★★★ If digital audio connections are not possible, connect the DVD/VCR’s red and white DVD/VCR AUDIO OUT
jacks to the Audio In jacks of your Stereo orTV. This connection provides sound for both the DVD player
and theVCR. See pages 10-11.
Before you begin...
● Refer to the manuals of yourTV, Cable Box, Stereo or other devices as necessary. Note the style of jacks and
connectors on the other equipment. Determine how to choose different Audio andVideo In channels on your
other equipment so you can see and hear the DVD/VCR material playing on theTV, Stereo, etc.
● Disconnect all equipment from the power outlets. Connect the equipment to power only after you have finished
hooking up everything. Never make or change connections with equipment connected to power.
Remember...
● Set theTV to the correctVideo In channel. Such channels may be called AUX or AUXILIARY IN, AUDIO/VIDEO or
A/V IN, EXT1 or External In, etc. These channels often are located near channel zero (0). Or, yourTV’s remote may
have a button or switch that selects theVideo Input channel. See yourTV manual for details. If you do not see the
DVD orVCR playback on theTV, go to the lowestTV channel (01 or 02) and change channels downward until you
see the DVD orVCR picture on theTV.
To help you find the right Audio/Video In channel, turn on the DVD/VCR. Press DVD to put the DVD/VCR in DVD
mode. With no disc in the player, a large DVDVideo logo will appear on theTV screen when you get theTV on the
correct Audio/Video In channel.
● Set the Stereo to the correct channel or “source” mode.
● Depending on your connection, you may need to purchase additional cables or adaptors. If yourTV or monitor has
BNC-type connectors, you will need an adaptor.
Once you determine the best option, find your choice on pages 9-12. Follow the steps for the hookup
you choose.Then, go to page 14 to complete the first-time setup.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 9
Hookups (cont’d) 9
DVD/VCR to An ExternalTuner
This DVD/VCR does not have a tuner input jack.To record TV programs on your DVD/VCR, you need to
connect this DVD/VCR to an external tuner device (e.g., set top box, cable box or satellite receiver) that
has audio/video output jacks.
Back of TV
e.g.)
RF coaxial cable
(not supplied)
AUDIO IN
TV Signal
L
Audio Cable
(not supplied)
ANT. IN
R
2
VIDEO IN
1
6
RF coaxial cable
(not supplied)
5
Video Cable
(not supplied)
DVD
DVD/VCR VCR
VIDEO
OUT
AUDIO OUT
T
DIGITAL
AUDIO S-VIDE
AUDIO OUT AUDIO IN
OUT
OUT
R
L
AUDIO OUT
L
L
L
R
R
P
B
COAXIAL
VIDEO OUT VIDEO IN
IN
OUT
R
DVD/VCR
Video Cable (supplied)
External tuner
4
3
Audio Cable (supplied)
Connections
Helpful Hints
Connect aTV signal to the IN jack on the external
tuner.
• If yourTV has antenna in jack
only, it is still possible to connect
this unit to yourTV by using a
commercially available stereo
audio/video RF modulator. Refer
to the manual accompanying the
modulator for more information.
• Required cables and connecting
methods differ depending on the
external tuner.
For more information, please
contact your external tuner
provider.
• Line through output
When an external device, such as
cable/satellite box, is connected
to L1(Rear) jacks of this
DVD/VCR, the signal from the
external device can be output
even when the power of the
DVD/VCR is off.
• Instead of using video out jack of
this DVD/VCR, you can also use
S-video out jack or component
video output jack for connecting
to yourTV.
1
2
Use an RF coaxial cable (not supplied) to connect
the OUT jack on the external tuner to the ANT. IN
jack on theTV.
Connect the red and white audio cable (supplied) to
the red and white AUDIO OUT jacks on the
external tuner and to the red and whiteVCR
AUDIO IN jacks on the DVD/VCR.
Connect the yellow video cable (supplied) to the
yellowVIDEO OUT jack on the external tuner and
to theVCRVIDEO IN jack on the DVD/VCR.
Connect another red and white audio cable (not
supplied) to the red and white DVD/VCR AUDIO
OUT jacks on the DVD/VCR and to the red and
white AUDIO IN jacks on theTV.
Connect another yellow video cable (not supplied)
to the DVD/VCRVIDEO OUT jack on the DVD/VCR
and to theVIDEO IN jack on theTV.
Connect the power cords of theTV and the DVD/VCR
to a power outlet. Turn on theTV and set it to the
correctVideo In channel.
3
4
5
6
7
8
You are ready to turn on the DVD/VCR. Go to page 14
to complete the first-time setup.
●
●
●
You can record any unscrambled channel by selecting the channel
on the external tuner. Be sure that the external tuner is turned on.
Signal from the external tuner can be output only on CVBS output
even when the power of the DVD/VCR is off.
You cannot record one channel while watching another
channel.
• Refer to the manual
accompanying external devices
for more information.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 10
10 Hookups (cont’d)
DVD/VCR to aTV that has Audio/Video, ComponentVideo or S-Video In jacks
Back ofTV
2b
COMPONENT
VIDEO IN
AUDIO IN
L
DVD
Audio and
Video IN Jacks
onTV
Y
COMPONENT
VIDEO OUT
AUDIO S-VIDEO
Audio Cable
(supplied)
1
OUT
OUT
AUDIO IN
VIDEO IN
Y
Cb/Pb
Cr/Pr
L
R
L
PB
R
P
R
R
1
Video Cable
(supplied)
a
Back ofTV
2
DVD
AUDIO IN
L
COMPONENT
VIDEO OUT
AUDIO S-VIDEO
OUT OUT
Y
1
L
S-VIDEO IN
DVD
DVD/VCR VCR
C
P
B
/
/
COMPONENT
VIDEO OUT
DIGITAL
AUDIO OUT
AUDIO IDEO
AUDIO OUT
B
OUT
UT
Y
L
L
R
R
L
C
P
R
C
B
/
/
R
R
R
P
B
COAXIAL
VIDEO OUT VIDEO IN
R
2c
Connect the red and white audio cable (supplied) to the
red and white DVD or DVD/VCR AUDIO OUT jacks on
1 the DVD/VCR and to the red and white AUDIO IN jacks
on theTV.
● If you are using DVD/VCR AUDIO OUT jacks for your
audio connection, use 2a method for your video connection.
If you are using DVD AUDIO OUT jacks for your audio
connection, use 2b or 2c method for your video connection.
Connect the yellow video cable (supplied) to the
2a
2b
2c
DVD/VCRVIDEO OUT jack on the DVD/VCR and to
theVIDEO IN jack on theTV. TheVIDEO IN jack on the TV
is usually yellow and may be labeled CVBS, Composite or
Baseband video.
Connect component video cable (not supplied) to the
COMPONENTVIDEO OUT jacks on the DVD/VCR
and to the COMPONENTVIDEO IN jacks on theTV.
The ComponentVideo In jacks on the TV are usually red,
blue and green.
Connect an S-Video cable (not supplied) to the
S-VIDEO OUT jack on the DVD/VCR and to the
S-VIDEO IN jack on theTV.
Connect the power cords of theTV and the DVD/VCR to
a power outlet. Turn on theTV and set it to the correct
3 Video In channel.
Helpful Hint
• Match the cable colors to the
jack colors. If theTV has a single
AUDIO IN jack, use the white
audio cable to connect the
If you are using the yellow video cable forVCR playback, choose
theVideo In channel at your TV. To find the correctVideo In
channel, go to your lowest TV channel and change channels
downward until you seeVCR playback on the TV screen.To help
you find the rightVideo In channel, turn on the DVD/VCR. Press
DVD to put the DVD/VCR in DVD mode. With no disc in the
player, a large DVDVideo logo will appear on the TV screen when
you get the TV on the correct Video In channel.
DVD/VCR’s white AUDIO OUT
(left) jack to theTV’s AUDIO IN
jack.You will not use the red
cable. Or, purchase a “splitter”
audio cable to go from the
left/right AUDIO OUT jacks of
the DVD/VCR to theTV’s single
AUDIO IN jack.
You are ready to turn on the DVD/VCR. Go to page 14 to
complete the first-time setup.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 11
Hookups (cont’d) 11
DVD/VCR to aTV and a Stereo
Back of TV
(example only)
DVD
DVD/VCR VCR
COMPONENT
VIDEO OUT
DIGITAL
AUDIO S-VIDEO
AUDIO OUT A
OUT
OUT
AUDIO OUT
Y
L
L
L
C
B
/
/
R
R
P
B
COAXIAL
VIDEO OUT VIDEO IN
R
CR
PR
Stereo
Audio Cable
(supplied)
VIDEO IN
AUDIO (LEFT) IN
AUDIO (RIGHT) IN
Video Cable
(supplied)
2
1
Connect the supplied red and white audio cable to the red and white
DVD/VCR AUDIO OUT jacks on the DVD/VCR and to the red and
white AUDIO IN jacks on the Stereo. Match the cable colors to the jack
colors.
1
2
3
Connect the supplied yellow video cable to the DVD/VCRVIDEO
OUT jack on the DVD/VCR and to theVIDEO IN jack on theTV.
To use ComponentVideo cable or S-Video cable instead for the DVD player,
see page 10. You will still need the yellow video cable forVCR features.
Connect the power cords of the DVD/VCR, TV and Stereo to a
power outlet. Turn on theTV and set it to theVideo In channel. Or,
simply go to your TV’s lowest channel (01 or 02) and continue changing
channels downward at the TV until you seeVCR or DVD playback on the TV
screen.
To help you find the rightVideo In channel at the TV, turn on the DVD/VCR. Press
DVD to put the DVD/VCR in DVD mode. With no disc in the player, a large DVD
Video logo will appear on the TV screen when you get the TV on the correct
Video In channel.
Turn on the Stereo and set it to the correct auxiliary or source mode.
Check your Stereo manual for details.
You are ready to turn on the DVD/VCR. Go to page 14 before
turning on the DVD/VCR.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 12
12 Hookups (cont’d)
DVD/VCR to aTV and to a Stereo that is Dolby Digital-compatible
Using Digital Audio connections
Back of TV
(example only)
DVD
DVD/VCR VCR
COMPONENT
VIDEO OUT
DIGITAL
AUDIO S-VIDEO
AUDIO OUT AUDIO IN
OUT
OUT
AUDIO OUT
Y
L
L
L
C
B
/
/
R
R
P
B
COAXIAL
VIDEO OUT VIDEO IN
R
C
R
PR
Stereo
2
VIDEO IN
Video Cable
(supplied)
1
COAXIAL
DIGITAL
AUDIO IN
Coaxial Digital Audio
Cable (not supplied)
Connect a coaxial digital audio cable (not supplied) to the DVD/VCR’s
COAXIAL DIGITAL AUDIO OUT jack and to the COAXIAL DIGITAL
1 AUDIO IN jack on the Stereo.
This digital audio connection only provides sound for the DVD player of the DVD/VCR.
So, in order to use theVCR features, connect the supplied red/white audio cable. To
connect the red/white audio cable, see step 5 on page 9.
Connect the supplied yellow video cable to the yellow DVD/VCRVIDEO
OUT jack on the DVD/VCR and to theVIDEO IN jack on theTV. To use
component video cable or S-Video cable instead for the DVD player, see
page 10.You will still need the yellow video cable forVCR features.
2
Plug in the power cords of the Stereo,TV and DVD/VCR.Turn on the
Stereo and select its Auxiliary IN channel.Turn on theTV and set it to
3 the correctVideo In channel. Go to yourTV’s lowest channel (01 or 02) and
change channels downward until you see DVD orVCR material on theTV screen.
To help you find the rightVideo In channel on theTV, turn on the DVD/VCR. Press
DVD to put the DVD/VCR in DVD mode. With no disc in the player, a large DVD
Video logo will appear on theTV screen when you get theTV on the correctVideo
In channel.
Make sure Progressive Scan (PROG. SCAN) is OFF and P.SCAN does not appear on
the DVD/VCR’s display panel. Disable Progressive Scan either in the DISPLAY
Menu or by pressing and holding PLAY B (DVD) on the front of the
DVD/VCR for more than 5 seconds. Details are on pages 8 and 51.
You are ready to turn on the DVD/VCR. Go to page 14 before turning on
the DVD/VCR.
4
Remember...
Some DVDs are recorded in Dolby Digital Multi-channel Surround Sound. Select Dolby
Digital Multi-channel Surround Sound in the DVD Disc Menu. If Dolby Digital Surround
Sound is not recorded on the disc, you will not have surround sound available.
If you connect the DVD/VCR to a Dolby Digital Stereo, set DOLBY DIGITAL to
BITSTREAM in the DVD player’s Setup Menu. Details are on page 52. If the DVD/VCR is not
connected to a Dolby Digital-compatible Stereo, set DOLBY DIGITAL to PCM.
Incorrect settings may cause noise distortion and damage the speakers.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 13
Remote Control Setup 13
Putting Batteries in the Remote Control
Remove the battery compartment lid on the bottom
of the remote control by pressing the tab, then lifting the
1
2
3
lid.
1
Place two AA batteries inside the battery
compartment with their
indicated.
ends aligned as
+ and –
Replace the battery compartment lid.
Using the Remote Control
● Point the remote control at the DVD/VCR’s remote sensor (see
page 18) when using the remote to operate the DVD/VCR. Do
not point the remote at the TV.
2
3
● Do not put objects between the remote and the DVD/VCR.
Recycling Guidelines/Battery Safety
● Your new product and its packaging contain materials that can
be recycled and reused. Specialized companies can recycle your
product to increase the amount that needs to be properly
disposed. Your product uses batteries that should not be
thrown away when depleted but should be disposed of as small
chemical waste. Please find out about the local regulations on
disposal of your old product, batteries and packaging whenever
you replace existing equipment.
● Battery Usage CAUTION - To prevent battery leakage that may
result in bodily injury, property damage or damage to the unit:
• Install ALL batteries correctly, with the
markings on
+ and –
the battery aligned as indicated on the unit.
• Do not mix batteries, for example, old with new or carbon
with alkaline.
• Remove batteries when the unit will not be used for a long
time.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 14
14 First-time DVD/VCR Setup
Before turning on your DVD/VCR, make sure batteries are in the
remote control and the DVD/VCR and TV are connected correctly.
These menus may not appear if you have already turned
on the DVD/VCR.
Turn on the TV.
1
Turn on theTV. Set it to the correctVideo In
2
OPEN/CLOSE
1
2
5
8
0
3
6
channel. (Check your TV owner’s manual for details.)
1
2
4
7
Pressy. VCR light will appear on the front of the
DVD/VCR. The display shown below will appear.
These menus may not appear if you have already turned on
the DVD/VCR. You may have turned on the DVD/VCR
before to find the Audio/Video In channel of the TV, for
example. If so, follow the steps on page 20 to select a
language for theVCR menus.
TRACKING
TITLE
9
CLEAR
+10
VCR
SETUP
DVD
DISC
INPUT
MENU
OK
3
LANGUAGE SELECT
BENGLISH
FRANCAIS
ESPAÑOL
[ON]
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
DISPLAY SUBTITLE ZOOM
PUSH
B
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
SPEED
MODE TIMER SET
Press K or L to select ENGLISH, FRANCAIS
(French) or ESPAÑOL (Spanish) as the language for
VCR On-Screen Displays and menus. Then, press B.
● To put the DVD/VCR inVCR mode, pressVCR soVCR
light appears.
3
Helpful Hints
• To skip this feature and play a
tape immediately, insert a tape
with its record tab removed.
• Repeat this process if the power
fails.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 15
Video Cassette Playback 15
Read and follow the steps below to play a tape.
Turn on theTV. Set it to the correctVideo In
channel. (Check your TV owner’s manual for details.)
Details are on page 8.
Turn on the TV.
1
2
1
2
Insert a tape in the
DVD/VCR.
Insert a tape in the cassette compartment of the
DVD/VCR. VCR light will appear on the front of the
DVD/VCR. If the tape’s record tab has been removed,
playback will start automatically.
OPEN/CLOSE
If the DVD/VCR power is already on, pressVCR to put the
DVD/VCR inVCR mode if necessary. VCR light will appear
on the front of the DVD/VCR.
1
4
2
5
8
0
3
6
TRACKING
TITLE
● If playback does not start automatically, pressVCR, then
press PLAY B.
7
9
CLEAR
● Press STOP C to stop playback.
● Press REW h to rewind the tape.
+10
● After the tape stops, press STOP/EJECT CA on the front
of the DVD/VCR to remove the tape.
VCR
SETUP
DVD
DISC
INPUT
MENU
OK
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
DISPLAY SUBTITLE ZOOM
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
SPEED
MODE TIMER SET
Helpful Hints
• Other tape playback features are
on pages 29-32.
• If AUTO REPEAT is ON, playback
will begin when you insert a tape,
even when the record tab is
intact. Details are on page 29.
• You must connect the DVD/VCR
to aTV using the audio/video
cables in order to use theVCR
features.These hookups are
explained on pages 9 and 11.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 16
16 Disc Playback
Before you begin, turn on the TV, Stereo and other equipment
connected to the DVD/VCR. Make sure the TV and the Stereo (if
applicable) are set to the correct channel.
1
3
OPEN/CLOSE
TRACKING
Details are on pages 8-12.
1
4
2
5
8
0
3
6
9
Pressy to turn on the DVD/VCR.
1
7
CLEAR
TITLE
+10
Press DVD so DVD light appears on the front of the
DVD/VCR.
VCR
SETUP
DVD
2
2
5
DISC
INPUT
MENU
Press OPEN/CLOSE A to open the disc tray.
3
OK
Place a disc onto the tray. If the DVD is recorded on
only one side, place the disc on the tray with the label
REW
PLAY
FFW
4
facing up and the shiny side facing down. Some DVDs are
STOP
PAUSE
BACK
recorded on both sides. Make sure the label of the side you
want to play is facing up.
Press PLAY B to close the tray. The tray will close and
playback will begin. If playback does not start automatically,
5
press PLAY B again.
Insert a disc.
If a DVD Menu appears instead, see page 32.
TM
4
To play MP3, Windows Media Audio or JPEG files, see
pages 43-44.
Helpful Hints
You also can close the tray by pressing
OPEN/CLOSE A.
● Press STOP C to stop playback.
• An “X” may appear at the top right
corner of the TV screen when you
try a feature. Either the feature is
not available on the disc, or the
DVD/VCR cannot access the
feature at this time. This does not
indicate a problem with the
DVD/VCR.
• If a disc is dirty or scratched, the
picture may appear distorted or
playback may stop. In such cases,
remove the disc and turn off the
DVD/VCR. Disconnect the power
cord, then reconnect it. Clean the
disc, then turn on the DVD/VCR
again and reinsert the disc for
playback.
• If a disc has multiple layers, the
picture may freeze occasionally. This
happens when the first layer
switches to the second layer. This is
not a malfunction.
• When the DVD or CD light
appears on the display panel, the
disc is loaded and ready for
playback.
• When you press OPEN/CLOSE
A
or PLAY B (DVD) on the front of
the DVD/VCR when the power is
off, the DVD/VCR will turn on in
DVD mode. Otherwise, the
DVD/VCR will turn on in the mode
in which it was turned off.
• If you use PLAY B to close the disc
tray, playback starts automatically. If
you use OPEN/CLOSE A to close
the disc tray, you have to press
PLAY B to start playback.
REMINDER:This DVD/VCR
will play only certain discs.
See page 7 for details.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.2.2 5:14 PM Page 17
Display Panel 17
DVD light
VCR light
This light appears when the DVD/VCR is inVCR mode.You can only
watch videotapes or accessVCR features whenVCR light is on.
To makeVCR light come on, pressVCR on the remote control or
SOURCE on the front of the DVD/VCR.
This light appears when the DVD/VCR is in
DVD mode. You can only watch DVDs when
DVD light is on. To make DVD light come
on, press SOURCE on the front of the
DVD/VCR or DVD on the remote control.
Display
Messages about current disc operations
appear here. See Display Messages below.
Cassette
Disc tray
Compartment
Insert a video
cassette here.
Insert a disc here.
DVD PLAYER/VCR DVP3345V
OPEN/CLOSE
ONE TOUCH RECORDING LONG PLAY
•
STANDBY-ON
VIDEO
L
AUDIO
R
REW
F.FWD STOP/EJECT PLAY
REC
TRACKING
VCR
DVD
STOP
PLAY
SOURCE
DVD
DVD Display Panel
Appears when a repeat function
is active.
Appears when
Appears when Progressive
Scan is active.
GROUP
P.SCAN
A-B Repeat is on.
DVD
Appears when
VCD
ALL Repeat is on.
(Video CD, CD, MP3,
TM
Windows Media Audio
Displays the elapsed time of the title
or track.
The number of a new title, chapter, or
track is displayed for 3 seconds when
a chapter or track is switched, or
DISPLAY is pressed during playback.
Displays the current disc type.
• DVD: DVD
• VCD: Video CD
and JPEG)
Appears when disc playback
is paused.
• CD: Audio CD, MP3,
TM
Appears during Slow Motion
Playback (DVD, Video CD).
Windows Media Audio,
JPEG
Appears during disc playback.
VCR Display Panel
Appears when an OTR,Timer Recording,
or Satellite Link has been set.
Appears during recording;
Indicates a tape is in the DVD/VCR.
REC
flashes when recording is
paused.
Appears during playback when
the Auto Repeat function is on.
PM
Indicates current time is P.M.
There is no A.M. indication.
Appears if tape playback
is paused.
Appears during Slow Motion
Playback.
Indicates the elapsed playing time of a tape; also displays a selected
external input channel, tape speed, remaining time for an
OTR or the current time.
Appears during tape playback.
Display Messages
Appears after the disc tray
Tray is closing.
Disc is loading.
closes if the tray is empty,
if there is an error reading
the disc, or if an unacceptable
disc is installed.
Appears when Playback
Control is active (Video CD).
Tray is opening or is open.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 18
18 Front Panel, Rear Panel and Remote Control
Front Panel
Remote Sensor
TRACKING
K
/L
Buttons
ySTANDBY-ON Button
OPEN/CLOSE A Button (DVD)
DVD PLAYER/VCR DVP3345V
OPEN/CLOSE
ONE TOUCH RECORDING LONG PLAY
•
STANDBY-ON
VIDEO
L
AUDIO
R
REW
F.FWD STOP/EJECT PLAY
REC
TRACKING
VCR
DVD
STOP
PLAY
VCR AUDIO and
VIDEO IN jacks (L2)
SOURCE
DVD
REW h Button (VCR)
REC
I
PLAY B Button (DVD)
STOP C Button (DVD)
SOURCE Button
Button (VCR)
F.FWD g Button (VCR)
STOP/EJECT C A Button (VCR)
PLAY B Button (VCR)
Rear Panel
Helpful Hint
DVD/VCR AUDIO and VIDEO OUT jacks
• The DVD S-VIDEO OUT,
DVD COMPONENT
VIDEO OUT, DVD
VCR AUDIO and
VIDEO IN jacks (L1)
DVD COMPONENT
VIDEO OUT jacks
AUDIO OUT and DVD
COAXIAL DIGITAL
DVD
DVD/VCR VCR
COMPONENT
VIDEO OUT
DIGITAL
AUDIO OUT
AUDIO S-VIDEO
AUDIO OUT AUDIO IN
OUT
OUT
Y
L
L
L
AUDIO OUT jacks are
only useful in DVD mode.
To have sound and picture
inVCR mode, you must
connect the audio/video
cables supplied. Details are
on pages 9-11.
CB
PB
/
/
R
R
COAXIAL
VIDEO OUT VIDEO IN
R
CR
PR
AC Power Cord
DVD S-VIDEO
OUT jack
DVD COAXIAL
DIGITAL AUDIO
OUT jack
DVD AUDIO
OUT jacks
Remote Control
y (STANDBY-ON) Button
OPEN/CLOSE
TRACKING
1
4
2
5
8
0
3
6
9
OPEN/CLOSE 0 Button
Number Buttons
TRACKING KL Button
7
CLEAR
TITLE
+10
TITLE Button
CLEAR Button
VCR Button
SETUP Button
Helpful Hints
VCR
SETUP
DVD
DISC
• For DVD player features,
press DVD before
DVD Button
INPUT
MENU
INPUT Button
s B KL Buttons
w (SKIP) Button
REW h Button
PLAY B Button
STOP C Button
DISPLAY Button
SUBTITLE Button
ANGLE Button
SEARCH Button
REC I Button
DISC MENU Button
OK
pressing other buttons.
To put the DVD/VCR in
DVD mode, press DVD
or SOURCE so DVD
light appears on the front
of the DVD/VCR.
OK Button
∑ (SKIP) Button
FFW g Button
BACK Button
PAUSE k Button
AUDIO Button
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
DISPLAY SUBTITLE ZOOM
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
• ForVCR features, press
VCR before pressing
other buttons.To put the
DVD/VCR inVCR mode,
pressVCR or SOURCE
soVCR light appears on
the front of the
ZOOM Button
SPEED
MODE TIMER SET
A-B REPEAT Button
REPEAT Button
TIMER SET Button
MODE Button
SPEED Button
DVD/VCR.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 19
Clock (VCR) 19
Follow these steps to set theVCR clock. Make sure:
PressVCR, then press SETUP so MENU appears. If the
OPEN/CLOSE
clock has never been set, the CLOCK SET Menu may
1
1
4
2
5
8
0
3
6
appear when you press SETUP. If so, follow the instructions
from step 3 on this page.
TRACKING
TITLE
- M E N U -
7
9
CLEAR
B TIMER PROGRAMMING
+10
SATELLITE LINK
AUTO REPEAT
CLOCK SET
[OFF]
VCR
SETUP
DVD
1
9
LANGUAGE SELECT
DISC
INPUT
MENU
OK
2-9
Press K or L to select CLOCK SET. Then, press B.
REW
PLAY
FFW
BACK
AUDIO
2
3
STOP
PAUSE
DISPLAY SUBTITLE ZOOM
While the MONTH space is flashing, press K or
until the month appears. Then, press B.
L
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
CLOCK SET
SPEED
MODE TIMER SET
MONTH DAY
0 3 – –
YEAR
– – – –
/
HOUR MINUTE
– – – –
AM/PM
– –
:
While the DAY space is flashing, press K or L until
the day appears. Then, press B.
4
5
While theYEAR space is flashing, press K or
L
until the year appears. Then, press B. The day of
the week will appear automatically.
Helpful Hints
• If the clock has never been set,
the CLOCK SET Menu may
appear when you press SETUP.
If so, follow the instructions
from step 3 above.
• Press DISPLAY repeatedly to
show the time on the TV
screen.
• Power failures of more than 30
seconds can erase the Clock
Setting.
• To reset the clock, follow steps
1-2. Select the information you
want to change using s or B.
When the information is
flashing, use K or L to enter
the correct information. Press
CLEAR to set the clock.
While the HOUR space is flashing, press K or
until the hour appears. Then, press B.
L
6
7
8
While the MINUTE space is flashing, press K or
L
L
until the minute appears. Then, press B.
While the AM or PM space is flashing, press K or
to point to AM or PM.
Your selection will flash on the screen in the AM/PM space.
Press CLEAR or B to start the clock.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 20
20 Language (VCR)
Follow the steps below to change the language of theVCR
On-Screen Displays and menus.
4
7
5
8
0
6
TRACKING
TITLE
9
CLEAR
+10
PressVCR, then press SETUP so MENU appears.
4
VCR
SETUP
DVD
1
- M E N U -
1
DISC
B TIMER PROGRAMMING
INPUT
MENU
SATELLITE LINK
AUTO REPEAT
CLOCK SET
[OFF]
OK
LANGUAGE SELECT
2-3
REW
PLAY
FFW
Press K or L to choose LANGUAGE SELECT,
then press B.
Helpful Hint
2
3
Press K or L to choose ENGLISH, FRANCAIS
• If you select FRANCAIS
(French), or ESPAÑOL (Spanish)
and need English:
1) Press SETUP so MENU
appears.
2) Press L to choose
SELECTION LANGUE or
SELEC. IDIOMA, then press B.
3) Press K or L to select
ENGLISH.
(French) or ESPAÑOL (Spanish).
LANGUAGE SELECT
B ENGLISH
FRANCAIS
ESPAÑOL
[ON]
4) Press CLEAR.
Press CLEAR to remove the menu.
4
VCR Status Displays
You may access Status Displays by pressing DISPLAY. The displays
may include the current time, external input channel and other
information.
VCR
SETUP
DVD
DISC
INPUT
MENU
OK
Press DISPLAY. The COUNT Display will appear for 5
seconds. After 5 seconds, only the real-time tape counter
1 will appear. This counter shows you the elapsed playing
REW
PLAY
FFW
BACK
AUDIO
time of the tape (from the point at which the counter was
set to 0). The counter also will appear on the display panel
on the front of the DVD/VCR.
STOP
PAUSE
DISPLAY SUBTITLE ZOOM
Press DISPLAY again. The CLOCK Display will appear
for 5 seconds. After 5 seconds, only the time will appear.
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
2
The time also will appear on the display panel on the front 1-3
of the DVD/VCR.
SPEED
MODE TIMER SET
STOP
STOP
5:40 PM
L2
Helpful Hint
SLP
0:12:34
SLP
•
You cannot access a Status
Display when viewing a still
picture, during slow motion, or
during Forward and Reverse
Searching.
Press DISPLAY again to remove all the displays.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 21
Videotape Recording 21
Read and follow the steps below to record a television program
onto a videotape.
Turn on the TV.
1
2
Before you begin:
Insert a tape in the
DVD/VCR.
● This DVD/VCR does not have a tuner input jack.To
recordTV programs on your DVD/VCR, you need to
connect this DVD/VCR to an external tuner device
(e.g., set top box, cable box or satellite receiver) that
has audio/video output jacks. See page 9 on how to connect
the DVD/VCR to the external tuner.
OPEN/CLOSE
● Make sure the DVD/VCR is inVCR mode. PressVCR soVCR
light appears on the front of the DVD/VCR.
1
4
2
5
8
0
3
6
TRACKING
TITLE
Turn on your external tuner, and turn on theTV
7
9
CLEAR
and set it to the correctVideo In channel. (Check
1
2
3
4
+10
your TV owner’s manual for details.)
VCR
SETUP
DVD
DISC
Insert a tape with its record tab intact into the
INPUT
MENU
cassette compartment of the DVD/VCR. If tape
4
playback begins, press STOP C.
OK
Press SPEED repeatedly until the desired tape
speed (SP or SLP) appears briefly on the screen.
REW
PLAY
FFW
BACK
AUDIO
Details about tape speed are on page 57.
STOP
PAUSE
Press INPUT to select the appropriate external
DISPLAY SUBTITLE ZOOM
input channel (L1/L2) to which your external tuner
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
is connected.Then select the desired channel to
record on the external tuner.
SPEED
MODE TIMER SET
5
Press REC I to start recording. “REC” will appear on
the DVD/VCR’s display panel.
5
● To pause the recording, press PAUSE k once.“REC” will
3
flash.To resume recording, press REC I or press
PAUSE k again.“REC” will reappear.
● To stop recording, press STOP C.
Helpful Hints
• Other recording options are on
pages 22-28.
• TheVCR will record in a preset
volume.
• Pause will switch to stop after 5
minutes to protect theVCR and
the tape from damage. When a
recording is paused, review the
pause time remaining with
the ■ marks on the screen.
Each ■ mark equals
Recording Prevention
Video cassettes have record tabs to ensure that recordings are
not accidentally erased.
● To prevent recording, break off the tab with a screwdriver.
● To allow recording, cover the hole with clear tape.
Cover the
hole to allow
recording.
Remove the
tab to prevent
recording.
1 minute remaining. During the
last minute of paused recording,
the ■ mark will flash.
• If any menu is on the TV screen,
REC I on the remote does not
function. Press CLEAR to
remove the menu. Then, press
REC I. Or, use REC I on the
front of the DVD/VCR.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 22
22 One-Touch Recording
One-Touch Recording (OTR) lets you set a timed recording 30
minutes to 8 hours long.
Before you begin:
OPEN/CLOSE
TRACKING
● This DVD/VCR does not have a tuner input jack.To
recordTV programs on your DVD/VCR, you need to
connect this DVD/VCR to an external tuner device
(e.g., set top box, cable box or satellite receiver) that
has audio/video output jacks. See page 9 on how to connect
the DVD/VCR to the external tuner.
1
4
2
5
8
0
3
6
9
7
CLEAR
TITLE
+10
● Place the DVD/VCR inVCR mode. PressVCR soVCR light
appears on the front of the DVD/VCR.
VCR
SETUP
DVD
● Select a recording speed (SP, SLP) by pressing SPEED.
● Put a videotape in the cassette compartment. Make sure the
tape’s record tab is intact and the tape is long enough to record
the program(s).
DISC
INPUT
MENU
1
2
OK
Press INPUT to select the appropriate external
input channel (L1/L2) to which your external tuner
REW
PLAY
FFW
BACK
AUDIO
1
2
is connected.Then select the desired channel to
record on the external tuner.
STOP
PAUSE
Press REC I repeatedly until the desired recording
DISPLAY SUBTITLE ZOOM
length (30 minutes to 8 hours) appears on theTV
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
screen. Recording will begin.“REC” and “ ” will appear
on the DVD/VCR’s display panel.
SPEED
MODE TIMER SET
OTR (0:30)
Helpful Hints
SP
• The remaining recording time
will appear on the display panel
during an OTR. Press DISPLAY
to see it on the TV screen.
• To change the recording length
while an OTR is in progress,
press REC I repeatedly.
• You cannot pause an OTR.
• If the preset time for a Timer
Recording comes up during an
OTR, the OTR has priority. The
Timer Recording will not take
place.
When an OTR ends
The DVD/VCR will turn off and “ ” on the DVD/VCR’s display
panel will flash indicating that the recording is complete, then goes
into the timer standby mode again. (It may switch to DVD mode
automatically.) At this point, you cannot use theVCR unless you
release the DVD/VCR from the timer standby mode.
To release the DVD/VCR from timer standby mode
● If the DVD component is active and no more Timer Recordings
are on standby, you can cancel the timer standby mode by
pressing TIMER SET orVCR on the remote control or by
pressing SOURCE or STOP/EJECT C A on the front panel.
● If the DVD component is not active, or the “ ” is not flashing
but lit indicating there are more Timer Recordings on standby,
you can cancel the timer standby mode only by pressing
TIMER SET on the remote control or by pressing
STOP/EJECT C A on the front panel.
• If the end of the tape is reached
during an OTR, theVCR will
stop recording, eject the tape,
and switch to DVD mode or
turn off.
• If one or more Timer
● After releasing the DVD/VCR from timer standby mode, you
can use it as usual.
Recordings are on standby
when one OTR ends, the
DVD/VCR will turn off
automatically and “ ” will
appear on the DVD/VCR’s
display panel indicating that it is
now ready for another Timer
Recording.
Stopping an OTR
● To stop an OTR before recording is finished, press STOP C on
the remote control or STOP/EJECT C A on the front of the
DVD/VCR.
● To cancel the OTR but continue recording, press REC
repeatedly until REC appears in the upper left corner of the TV
screen, and “ ” disappears.
I
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 23
Rerecording (Tape Duplication) 23
These instructions are made on the premise that the DVD/VCR 1 is already connected to theTV. The
instructions show you how to copy videotapes. The illustration uses two DVD/VCRs. OtherVCRs or
Camcorders may operate differently.
1. Audio cable from AUDIO OUT jacks (red and white)
of DVD/VCR 1 to AUDIO IN jacks of DVD/VCR 2
DVD
DVD/VCR VCR
COMONENT
DIGITAL
AUDIO S-VIDE
AUDIO OUT AUDIO IN
OUT
OUT
AUDIO OUT
L
L
L
/
R
R
P
B
COAXIAL
VIDEO OUT VIDEO IN
R
C
R
P
R
DVD/VCR 1
Playing unit
2.Video cable from yellowVIDEO
OUT jack of DVD/VCR 1 to
VIDEO IN jack of DVD/VCR 2
DVD
DVD/VCR VCR
COMPONEN
VIDEO OU
DIGITAL
AUDIO OUT
AUDIO S-VIDEO
AUT AUDIO IN
OUT OUT
Y
L
L
C
B
/
/
R
R
P
B
COAXIAL
VIDEO OUT VIDEO IN
R
C
R
P
R
DVD/VCR 2
Recording unit
Make the connections shown above.
1
2
3
4
5
6
7
DVD/VCR 1 will play your tape. Put a prerecorded tape
into the cassette compartment of DVD/VCR 1.
PressVCR to put the unit inVCR mode if necessary.
DVD/VCR 2 will record your tape. Insert a blank tape in
the cassette compartment of DVD/VCR 2. PressVCR
to put the unit inVCR mode if necessary.
Turn on theTV and set it to the correctVideo In
channel. (Check your TV owner’s manual for details.)
Helpful Hints
• If you use the AUDIO and
VIDEO IN jacks on the back of
DVD/VCR 2, select L1 at step 5.
• If you use the AUDIO and
VIDEO IN jacks on the front of
DVD/VCR 2, select L2 at step 5.
• Unauthorized recording of
copyrighted television programs,
video tapes or other materials
may infringe on the rights of
copyright owners and violate
copyright laws.
Point the remote control at DVD/VCR 2. Press
INPUT to select the appropriate external input
channel. (See Helpful Hints to the right.)
Press SPEED to select SP or SLP at DVD/VCR 2.
Details about tape speed are on page 57.
Press PLAY B (VCR) on the front of DVD/VCR 1
and REC I on the front of DVD/VCR 2 at the same
time.
● To stop recording, press STOP/EJECT C A on DVD/VCR
2, then press STOP/EJECT C A on DVD/VCR 1.
• If a program has copyright
protection, it may not be
recorded clearly.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 24
24 Timer Recording
Follow the steps below to program theVCR of the DVD/VCR to
record TV programs while you’re away from home. Before you begin:
● This DVD/VCR does not have a tuner input jack.To
recordTV programs on your DVD/VCR, you need to
connect this DVD/VCR to an external tuner device
(e.g., set top box, cable box or satellite receiver) that
has audio/video output jacks. See page 9 on how to connect
the DVD/VCR to the external tuner.
OPEN/CLOSE
TRACKING
1
4
2
5
8
0
3
6
9
7
CLEAR
TITLE
+10
● Set the clock. Details are on page 19.
● Put a tape in the cassette compartment of the DVD/VCR. Make
sure the tape’s record tab is intact and the tape is long enough
to record the program(s).
VCR
SETUP
DVD
DISC
INPUT
MENU
1
● PressVCR soVCR light appears on the front of the DVD/VCR.
● Turn on your external tuner.
OK
Press SETUP so MENU appears.
2-6
REW
PLAY
FFW
BACK
AUDIO
1
Press K or
L
B
to selectTIMER PROGRAMMING.
STOP
PAUSE
Then, press
. Program numbers that do not have a Timer
2 Recording stored will flash.
DISPLAY SUBTITLE ZOOM
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
TIMER PROGRAMMING
PROG. 12345678
DATE
SPEED
MODE TIMER SET
STARTTIME
END TIME
L1/L2
REC SPEED
Helpful Hints
• You cannot access the TIMER
PROGRAMMING Menu at step
2 if the clock is not set.The
CLOCK SET Menu will appear.
Follow the steps on page 19 to
set the clock.
• Only programs that will air
Monday-Friday can be recorded
on a DAILY basis. If you select
DAILY at step 4, then enter a
Saturday or Sunday DATE at step
5, the correct program will not
be recorded. TheVCR will alter
the recording date and record a
different program than the one
you intended.
• If you connected the external
tuner to the AUDIO andVIDEO
IN jacks on the front of the
DVD/VCR, choose L2. If you
connected the external tuner to
the AUDIO IN andVIDEO IN
jacks on the back of the
Press K or L to select an empty program.
Then, press B.
3
PROGRAM NUMBER
1
DATE
– – / – –
STARTTIME
END TIME
L1/L2
– – : – – – –
– – : – – – –
– –
REC SPEED
– –
Press K or L to select ONCE, DAILY orWEEKLY.
Then, press B.
4
5
● ONCE -TheVCR will record aTV program on any day you
choose, up to 12 months away.
● DAILY - TheVCR will record aTV program at the same time
on the same channel every day, Monday through Friday.
●
WEEKLY -TheVCR will record aTV program at the same time
on the same channel every week, for example, every Monday.
To set the recording date and time, press K or
until the desired setting appears, then press B.
L
Press K or L to select the appropriate external
input channel (L1/L2) to which your external tuner
6 is connected.Then select the desired channel to
DVD/VCR, choose L1.
• Enter the information while the
space is flashing.
• You cannot program more than
one year in advance.
record on the external tuner.
● Leave the external tuner on for the Timer Recording. Details
are on page 9.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 25
Timer Recording (cont’d) 25
Press K or L to select a recording tape speed. The arrow
will appear beside your choice. The selected speed will flash
7 beside REC SPEED. Details about tape speed are on page 57.
You must select the recording speed to complete the
timer programming.
OPEN/CLOSE
1
4
2
5
8
0
3
6
9
ONETIME PROGRAM
TRACKING
PROGRAM NUMBER
1
7
DATE
0 8 / 2 9 WED
CLEAR
TITLE
DVD
STARTTIME
END TIME
L1/L2
0 7 : 3 0 P M
0 8 : 3 0 P M
+10
L2
S P
SP
REC SPEED
VCR
SETUP
B
8
7
SLP
DISC
INPUT
MENU
Press CLEAR to remove the menu.
OK
8
PressTIMER SET.
● In some cases, the DVD/VCR will switch to DVD mode
instead.
You may use the DVD player during a Timer Recording.
● If you want to use theVCR until time for the recording,
don’t press TIMER SET until a few minutes before the
recording should start. Or, press TIMER SET only when you
know you won’t be using theVCR anymore (until after the
recording).
REW
PLAY
FFW
BACK
AUDIO
9
STOP
PAUSE
DISPLAY SUBTITLE ZOOM
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
SPEED
MODE TIMER SET
● When “ ” is lit (not flashing), you cannot put the
DVD/VCR inVCR mode by pressingVCR or SOURCE
.
9
You must first press TIMER SET on the remote control or
STOP/EJECT C A on the front panel to cancel the Timer
Recording temporarily. Then, you can use theVCR features
again.
When a Timer Recording ends
The DVD/VCR will turn off and “ ” on the DVD/VCR’s display panel
will flash indicating that the recording is complete, then goes into the
timer standby mode again. (It may switch to DVD mode
automatically.) At this point, you cannot use theVCR unless you
release the DVD/VCR from the timer standby mode.
To release the DVD/VCR from timer standby mode
●
If the DVD component is active and no more Timer Recordings are
on standby, you can cancel the timer standby mode by pressing
TIMER SET orVCR on the remote control or by pressing SOURCE
or STOP/EJECT C A on the front panel.
If the DVD component is not active, or the “ ” is not flashing but
lit indicating there are more Timer Recordings on standby, you can
cancel the timer standby mode only by pressing TIMER SET on the
remote control or by pressing STOP/EJECT C A on the front panel.
Helpful Hints
●
•
To stop a started Timer Recording,
press STOP/EJECT C A on the
front of the DVD/VCR. (You cannot
stop a started Timer Recording with
STOP C on the remote.)
● After releasing the DVD/VCR from timer standby mode, you can use
it as usual.
• To change incorrect information,
press s or B to choose the
item you want to change. Press
K or L to adjust the information.
• If there is no tape in theVCR
when you pressTIMER SET,
Canceling aTimer Recording Before the Recording Starts
PressVCR, then press SETUP so MENU appears.
1
Press K or L to select TIMER PROGRAMMING,
then press B.
“
” will flash. Insert a tape.
2
• If one or moreTimer Recordings
are on standby when one Timer
Recording ends, the DVD/VCR
will turn off automatically and
Press K or L to find the program you want to
cancel.
3
While the program number is flashing, press s to
clear all the information for that program.
“
” will appear on the
DVD/VCR’s display panel
4
indicating that it is now ready for
another Timer Recording.
Press CLEAR to remove the menu.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 26
26 Satellite Link
You can set the DVD/VCR to start recording whenever it detects
a video signal from the external tuner.
Before you begin:
OPEN/CLOSE
TRACKING
● Set the clock. Details are on page 19.
1
4
2
5
8
0
3
6
9
● Put a tape in the cassette compartment of the DVD/VCR. Make
sure the tape’s record tab is intact and the tape is long enough
to record the program(s).
● PressVCR soVCR light appears on the front of the DVD/VCR.
● Turn on the external tuner.
7
CLEAR
TITLE
+10
● Use theVCR AUDIO andVIDEO IN jacks on the rear (L1) to
connect the DVD/VCR to the external tuner. VCR AUDIO and
VIDEO jacks on the front (L2) cannot read any signal from the
external tuner.
● If the external tuner is equipped with some kind of timer
function, set it to output audio/video signals when it comes to
the time you want to start recording and stop when it comes to
the time you want to stop recording. Refer to the tuner’s
manual on how to set the timer.
VCR
SETUP
DVD
2
4-6
DISC
INPUT
MENU
OK
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
● If the external tuner is not equipped with timer function, leave it
on for Satellite Link Recording.
DISPLAY SUBTITLE ZOOM
L1
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
To audio/video
input jacks
DVD
DVD/VCR VCR
External tuner
COMPONENT
VIDEO OUT
DIGITAL
AUDIO OUT
AUDIO S-VIDEO
AUDIO OUT AUDIO IN
OUT
OUT
Y
L
SPEED
MODE TIMER SET
L
C
P
B
/
/
R
R
B
COAXIAL
VIDEO OUT VIDEO IN
R
C
P
R
R
Audio/Video Cables
(supplied)
DVD/VCR
1
Press SPEED repeatedly until the desired tape
speed (SP or SLP) appears briefly on the screen.
Details about tape speed are on page 57.
1
2
3
In stop mode, press SETUP.
Press K or L to select SATELLITE LINK,
then press B.
- M E N U -
TIMER PROGRAMMING
B SATELLITE LINK
AUTO REPEAT
CLOCK SET
[OFF]
LANGUAGE SELECT
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 27
Satellite Link (cont’d) 27
Press K or L to set the desired start hour,
then press B.
4
SATELLITE LINK
1 2 : 0 0 AM
● The hour can be selected from 1-12 with AM or PM.
● When the external tuner signal is stopped, recording will
be stopped also.
Press K or L to set the desired start minutes.
If you wish to go back to the left, press s.
5
6
SATELLITE LINK
Helpful Hints
0 1 : 0 0 PM
• If you have not set the clock,
CLOCK SET menu will appear at
step 3. Refer to “Clock (VCR)”
on page 19.
• You cannot set the ending time
for the Satellite LinkTimer
Recording on this DVD/VCR.
• Recording picture will be
distorted if the copy protection
signal is being detected during
Satellite LinkTimer Recording.
• When a regularTimer Recording
and the Satellite LinkTimer
Recording are overlapped, those
recordings are recorded as
illustrated below.
Press B to set Satellite Link standby mode.
SATELLITE LINK
0 1 : 3 0 PM
[ON]
●
“
”
on the DVD/VCR’s display panel lights up and the
e.g.) In case of the Satellite Link Timer Recording is
overlapped on the existing Timer Recording.
DVD/VCR goes to the DVD mode. If you do not use
DVD function, turn off the DVD/VCR.
Timer Recording
Satellite Link
● If the external tuner is not equipped with timer function,
leave it on for Satellite Link Recording.
recording result
●
To cancel the Satellite Link function in standby mode:
Press TIMER SET on the remote control or
STOP/EJECT C A on this DVD/VCR.
e.g.) In case of the Timer Recording is programmed in the
middle of the Satellite Link Timer Recording.
●
To cancel the Satellite Link function while the Satellite
Link Recording is in progress:
Press STOP/EJECT C A on the DVD/VCR.
Timer Recording
Satellite Link
recording result
e.g.) In case of the Timer Recording is overlapped on the
existing Satellite Link Timer Recording.
Timer Recording
Satellite Link
recording result
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 28
28 DVD to Videotape Duplication
Follow the steps below to copy a DVD to a videotape. This will
be possible only if the DVD is not copy protected.
Before you begin:
● Put a videotape in the cassette compartment. Make sure the
tape’s record tab is intact and the tape is long enough to record
the DVD.
OPEN/CLOSE
TRACKING
1
4
2
5
8
0
3
6
9
● Put the DVD you want to copy in the disc tray.
● PressVCR soVCR light appears on the front of the DVD/VCR.
7
CLEAR
TITLE
+10
●
Turn on the TV and set it to the correctVideo In channel.
(Check your TV owner’s manual for details.)
VCR
SETUP
DVD
DISC
4
INPUT
MENU
1
Press INPUT repeatedly until “DISC” appears on the
OK
TV screen.
1
DISC
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
DISPLAY SUBTITLE ZOOM
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
SPEED
MODE TIMER SET
Press SPEED repeatedly until the desired tape
speed (SP or SLP) appears briefly on the screen.
Details about tape speed are on page 57.
3
2
2
3
4
Press REC I to start recording. “REC” will appear on
the display panel.
Press DVD. Press PLAY B to play the disc.
●
●
●
To pause the recording, pressVCR, then press
PAUSE
To resume recording, press REC
again. REC will reappear.
To stop recording, pressVCR, then press STOP
k
once.
“REC” will flash.
I
or press PAUSE
k
“
”
C.
Helpful Hints
• A Timer Recording or Satellite
Link is not available during DVD
to videotape duplication.
• You cannot copy a DVD to a
videotape if you are using
Progressive Scan.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 29
Repeat Playback 29
Follow the steps below to play a videotape repeatedly.
1
2
5
8
0
3
4
6
PressVCR, then press SETUP so MENU appears.
TRACKING
TITLE
7
9
1
CLEAR
+10
Press K or L to select AUTO REPEAT.
2
VCR
SETUP
DVD
1
2-3
DISC
Press B so ON appears next to AUTO REPEAT.
INPUT
MENU
1
Tape playback will begin immediately. AUTO REPEAT will
3
OK
appear on the TV screen briefly. (If you are fast forwarding
or rewinding the tape, press CLEAR to remove the menu,
then press PLAY B to begin tape playback.) The tape will
play to the end, rewind, then play again.
REW
PLAY
FFW
- M E N U -
TIMER PROGRAMMING
SATELLITE LINK
B AUTO REPEAT
CLOCK SET
LANGUAGE SELECT
[ON]
Helpful Hint
• To cancel Auto Repeat, follow
steps 1-2. At step 3, press
B
so OFF appears beside AUTO
REPEAT. Press CLEAR.
Tape Counter
Follow the steps below to reset theVCR’s real-time tape counter
to 0 at a tape location you want to refer to later.
4
5
8
0
6
TRACKING
7
9
PressVCR, then play, fast forward or rewind a tape
to the location that you would like to refer to later.
CLEAR
TITLE
+10
1 Press STOP
C to stop the tape.
VCR
SETUP
DVD
3
Press DISPLAY to see the Status Display.
DISC
1
INPUT
MENU
2
STOP
OK
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
SLP
1 : 23 : 45
1
DISPLAY SUBTITLE ZOOM
While the counter is on the screen, press CLEAR to
reset the counter to 0.
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
3
4
SPEED
MODE TIMER SET
STOP
2,4
Helpful Hints
• You may only set the counter to
0 at one location at a time.
Setting the counter to zero at a
second location will erase the
previous 0 setting.
• If you remove the tape, the
counter will reset to 0 at the
point at which you last stopped
playback whenever you reinsert
the tape.
SLP
0 : 00 : 00
When you later want to return to this point on the
tape, press DISPLAY so you can see the counter
4 (while tape playback is stopped). Press REW
h or
FFW g.
As the tape rewinds or forwards, watch the counter. When
it reaches 0, press PLAY B to play the tape.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 30
30 Time Search, Index Search
Time Search
Follow the steps below to search forward or backward on a tape
a specific length of time. There must be a tape in the cassette
compartment.
4
7
5
8
0
6
TRACKING
TITLE
9
CLEAR
PressVCR, then press SEARCH repeatedly until the
+10
TIME SEARCH Screen appears.
1
VCR
SETUP
DVD
DISC
1
TIME SEARCH
- : - -
INPUT
MENU
OK
2-3
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
Within 30 seconds, press K or L until your desired
length of time appears. Or, press and hold K or L until
you reach the desired length of time.
You can set aTime Search for up to 9 hours and 59 minutes
(9:59).
DISPLAY SUBTITLE ZOOM
2
3
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
1
SPEED
MODE TIMER SET
Within 30 seconds, press s (for a reverse search) or
(for a forward search). TheVCR begins rewinding or fast
B
forwarding the tape.When the tape finishes rewinding or fast
forwarding the time you specified, playback will begin.
The time will count down beneathTIME SEARCH during the
search.
If the end of the tape is reached during the search, the search
will stop and the tape may rewind. Details are on page 31.
Index Search
4
5
8
0
6
TRACKING
An Index Mark is made automatically at the beginning of each
recording. Essentially, an Index Mark is a “bookmark.” Find the start
of a recording by following these steps.
7
9
CLEAR
TITLE
DVD
+10
VCR
PressVCR, then press SEARCH repeatedly until the
SETUP
DISC
INDEX SEARCH Screen appears.
1
1
INPUT
MENU
INDEX SEARCH
– –
OK
2-3
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
DISPLAY SUBTITLE ZOOM
Within 30 seconds, press K or L until the number of
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
programs you want to skip appears beneath INDEX
1
2
3
SPEED
MODE TIMER SET
SEARCH. Include the current program in your number.
Within 30 seconds, press s (for a reverse search) or
B
(for a forward search). When the tape finishes rewinding or
forwarding, playback will start. The program numbers will
count down beneath INDEX SEARCH during the search.
If the end of the tape is reached during the search, the search
will stop and the tape may rewind. Details are on page 31.
Recordings should be at least 1 minute long in SP speed and
3 minutes in SLP. Otherwise, the Index Mark will not be
available. Details on tape recording speeds are on page 57.
Helpful Hints
• Time Search and Index Search
are not available during
recording.
• To remove a Search Display, press
CLEAR.
• To cancel a search, press
STOP C.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 31
Special Effects Playback 31
●
Before you begin, pressVCR soVCR light appears on the front of the
1
2
5
8
0
3
DVD/VCR.
4
6
Forward and Reverse Searching (SP/LP/SLP) /
Super High Speed Searching (LP/SLP)
TRACKING
TITLE
7
9
CLEAR
+10
During tape playback, press and release FFW
g
or REW h. A fast forward or reverse picture search
VCR
SETUP
DVD
1 will begin.
DISC
Press FFW g or REW h, then press again. The
INPUT
MENU
search speed will increase. Repeatedly pressing FFW
g
or REW h will switch between Regular and High Speed
OK
Searching.
To return to normal playback, press PLAY B.
REW
PLAY
FFW
2
STOP
PAUSE
BACK
Viewing a Still Picture
During tape playback, press PAUSE k. A still picture
will appear on the screen.
Helpful Hints
1
● To advance the still picture one frame at a time, press
• Slow and still modes will switch
to stop mode after 5 minutes
to protect the DVD/VCR and
the tape from damage.
SP/LP/SLP means this feature will
work with tapes recorded in
Standard Playback, Long Playback or
Super Long Playback. LP/SLP means
this feature will work with tapes
recorded in Long Playback or Super
Long Playback. Tape speed details
are on page 57.
PAUSE k repeatedly.
● To release the still picture and return to playback, press
PLAY B.
•
Viewing a Slow Motion Picture
During tape playback, press PAUSE k, then press
FFW g. The tape will play in slow motion.
1
● To change the playback speed, press FFW g or
REW h.
● To return to normal playback, press PLAY B.
Automatic Operation Features
The following tape features are available inVCR mode. PressVCR soVCR light appears on the front of the DVD/VCR, if
necessary.
Automatic Playback
When you put a tape in the DVD/VCR, the power will come on. If the tape’s record tab is missing, playback will begin.
If a Timer Recording is set and “ ” is flashing in the display panel, the power will not come on automatically
when you insert a tape with the record tab intact.
If a Timer Recording is set and “ ” is flashing in the display panel, the DVD/VCR will eject the tape if the record
tab is missing.
Automatic Rewind, Eject
When a tape is played, fast forwarded or recorded to its end, the tape will rewind to the beginning, stop and eject
itself. This feature does not operate if AUTO REPEAT is ON. Details are on page 29.
Tape Eject
A tape can be ejected with the DVD/VCR power on or off (but the DVD/VCR must be plugged in).
If a Timer Recording is set and “ ” is shown on the display panel, press TIMER SET on the remote control or
STOP/EJECT C A on the front panel to cancel the timer standby mode, and then press STOP/EJECT C A to
remove the tape. Remember to insert a tape and press TIMER SET to reset the Timer Recording.
AutomaticTracking Adjustment
TheVCR adjusts tracking automatically to give you the best possible picture quality. With some recordings, however,
you may get a better picture using manual tracking.
ManualTracking
To manually adjust the tracking during normal playback and Slow Motion Playback of a videotape, press
TRACKING K/L. Tracking will return to Automatic Tracking when you press STOP C or insert a tape. You
can also press TRACKING K/L to remove vertical jitter in a Still picture.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN1.qxd 09.1.23 2:42 PM Page 32
32 Hi-Fi Stereo
Hi-Fi Stereo
To play in Hi-Fi stereo the tapes recorded in Hi-Fi stereo, press
AUDIO to switch Hi-Fi or MONO.
Helpful Hint
• The audio level of a tape
recorded in Hi-Fi stereo will
differ from the audio level of a
tape not recorded in Hi-Fi stereo.
Menus, Playback Control (PBC) Function
DVD Disc Menus
VCR
SETUP
DVD
Some DVDs contain menus that describe the contents of the disc
1
DISC
or allow you to customize disc playback. For example, the menu
INPUT
MENU
may offer choices for subtitle languages, director’s commentary or
Sound Track Playback. To use the DVD Menu and select playback
features, follow these steps.
OK
2
3
Press DVD to put the DVD/VCR in DVD mode.
TRACKING
TITLE
DVD light will appear on the front of the DVD/VCR.
7
8
0
9
1
2
3
CLEAR
Press DISC MENU. The DVD’s main Disc Menu will
appear.
+10
2
1
VCR
SETUP
DVD
Press K, L, s or B to select an item, then press OK.
Continue this process to set up all the features you want.
DISC
INPUT
MENU
OK
Using theTitle Menu
Some DVDs have a Title Menu, which lists the titles available on
the DVD. Use the Title Menu to play a specific title.
3
1
1
4
2
3
6
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
5
8
0
1
TRACKING
TITLE
PressTITLE. The Title Menu will appear.
7
9
CLEAR
If a Title Menu is not available, the “X” may appear on the
2
+10
VCR
TV screen. Or, if the DVD only has a main Disc Menu as
described above, it may appear when you press TITLE.
SETUP
DVD
DISC
Press K, L, s or B to select a title, then press OK.
Playback will begin at the title you selected.
INPUT
MENU
3
OK
Playback Control (PBC) Function
When playing aVideo CD with PBC (Playback Control), you can
use interactive menu (e.g., playlists) on the TV screen. Refer to
instructions accompanying yourVideo CD for more details on
PBC.
REW
PLAY
FFW
2
STOP
PAUSE
BACK
Some operations cannot be performed unless the PBC function is
cancelled temporarily.
Helpful Hints
• Menus vary among discs. Follow
the literature accompanying the
disc for details.
Canceling and calling back the PBC function
While playback is stopped, press the Number
• Not all DVDs have Disc or Title
Menus.
Buttons to enter a track number.
1
PBC function is now cancelled and the playback of the
• Some DVDs may refer to
chapters as “scenes.” Some
DVDs may refer to the Title
Menu as the “scene index.”
• TITLE will not be active with all
DVDs.
Video CD will start.
To call back the PBC function, press STOP C twice,
then press PLAY B.
The Title Menu will appear on the TV screen.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 33
Fast Forward/Fast Reverse 33
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
OPEN/CLOSE
1
2
1
4
2
5
8
0
3
6
9
During playback, press FFW g or REW h on
the remote control.
TRACKING
● During DVD playback, pressing FFW g or REW h will
forward or reverse the picture at approximately 2, 8, 20, 50
or 100 times the normal speed. The speed may vary
depending on the disc. g 1, g 2, g 3, g 4 or
g 5 will appear briefly on the TV screen to indicate
Forward Searching. Or, h 1, h 2, h 3,h 4 or
h 5 will indicate fast reverse.
7
CLEAR
TITLE
DVD
+10
VCR
SETUP
DISC
1
2
INPUT
MENU
OK
For DVD playback, the sound will be mute during the
search.
TM
● ForVideo CDs,Audio CDs, MP3 or Windows Media
REW
PLAY
FFW
BACK
AUDIO
Audio playback, pressing FFW g or REW h will
forward or reverse the picture or sound at
approximately 2, 8 or 30 times the normal speed. The
speed may vary depending on the disc.
2
3
STOP
PAUSE
DISPLAY SUBTITLE ZOOM
g 1, g 2 or g 3 will appear briefly on the TV
screen to indicate Forward Searching. Or, h 1, h 2
or h 3 will indicate fast reverse.
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
SPEED
MODE TIMER SET
TM
For Audio CD, MP3 or Windows Media Audio playback,
the sound will be intermittent during the search.
E
1
Example: Playing a DVD in
reverse at twice the normal
playing speed.
Helpful Hint
• If you use FFW g or
REW h during Dual Playback,
JPEG playback will be paused.
Press PLAY B to return to normal playback.
3
x1.3 and x0.8 Rapid Play with Voice
Rapid Play withVoice is available only during playback on the
discs recorded in the Dolby Digital format. Rapid Play with
Voice plays back in slightly faster/slower speed while keeping
the sound quality as in the normal playback.
Helpful Hint
• During Rapid Play withVoice;
- Audio Language Setting, Black
Level Setting andVirtual
Surround Setting cannot be
changed.
- Virtual Surround does not
function.
- the PCM sound will be output
if using the digital audio
connection (COAXIAL).
- depending on the scenes you
are playing, Rapid Play with
Voice may be unavailable.
During playback, press MODE.
The current setting appears.
1
2
Press OK to switch among
(x1.3), (x0.8) and
OFF.
: Plays back approximately at 1.3 times of normal playback.
: Plays back approximately at 0.8 times of normal playback.
OFF : No effects.
● To resume normal playback, press PLAY B.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 34
34 Title/Chapter/Time Search
Title/Chapter Search
OPEN/CLOSE
TRACKING
1
4
2
5
8
0
3
6
9
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
1
7
3
CLEAR
TITLE
During DVD playback, press SEARCH repeatedly
until CH (for chapter) or TT (for title) appears on the TV
screen. The number of available titles or chapters will
appear at the right ( /4, for example).
+10
2
VCR
SETUP
DVD
DISC
1
1
INPUT
MENU
Enter the title or chapter number using the
OK
Number buttons. The title or chapter will play.
3
● To select a single-digit track number when there are
more than 10 tracks, press OK to play the track.
● If you enter a track number that is not available on the
Disc, playback will not begin (or the current track will
continue to play).
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
DISPLAY SUBTITLE ZOOM
12/17
4 / 4
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
2
3
SPEED
MODE TIMER SET
OPEN/CLOSE
3
1
4
2
5
8
0
6
TRACKING
Time Search
7
9
CLEAR
TITLE
DVD
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
+10
VCR
1
2
SETUP
DISC
During DVD, Video CD (without PBC) or Audio CD
playback, press SEARCH repeatedly until the Time
Search Display appears.
INPUT
MENU
OK
_:_ _:_ _
1:29:00
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
DISPLAY SUBTITLE ZOOM
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
2
SPEED
MODE TIMER SET
Within 30 seconds, use the Number buttons to
enter the elapsed playing time (of the track or title)
at which you want playback to begin. Enter the time
in hours, minutes and seconds. Within a few seconds, play-
back will start at the specified time.
● Example: 1 hour, 23 minutes and 30 seconds
1 → 2 → 3 → 3 → 0
● Make sure the time you enter is within the total time of
the current title or track. If it is not, the time space will
clear and playback will continue at its current point. The
total time available in the current track or title will
appear in the Time Search Display.
● If you make a mistake entering the time, press CLEAR to
clear the time area. Enter the correct information.
3
Helpful Hints
• When playback is stopped, use
the Number buttons to select a
title for immediate playback.
During playback, use the
Number buttons to choose a
chapter for immediate playback.
• Title/Chapter Search is not
available with some DVDs.
• Time Search is not available for
TM
MP3,Windows Media Audio
and JPEG files.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 35
Track Search 35
There are three ways to play a specific Video CD (without PBC),
TM
Audio CD, MP3, Windows Media Audio or JPEG track: Use the
Number buttons, the SEARCH button or ∑ and w.
● Before you begin, press DVD so DVD light appears on the front of
the DVD/VCR.
OPEN/CLOSE
1
4
2
5
8
0
3
6
TRACKING
TITLE
7
9
A,B
CLEAR
A
+10
Using the Number Buttons
Press the Number buttons to enter a track number.
Playback will start at the selected track.
VCR
SETUP
DVD
DISC
INPUT
MENU
For tracks 10 and above, press the +10 button so the Search
Display (TR _ _ /12 - an example of total tracks) appears on the
TV screen. Press the Number button of the first digit, then press
the Number button of the second digit. For example, to play track
26, press +10, then Number 2, then Number 6 (Each number must
be pressed within 30 seconds of the previous number).
For single-digit tracks (1-9), press a single Number button.
If you enter a track number that is not available on the disc, play will
not begin (or the current track will continue to play).
OK
REW
PLAY
FFW
C C
STOP
PAUSE
BACK
AUDIO
DISPLAY SUBTITLE ZOOM
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
SPEED
MODE TIMER SET
B
Using SEARCH
B
Press SEARCH so theTrack Search Display (TR) appears.
Within 30 seconds, press the Number buttons to select the
track number. Playback will begin at the selected track. For a
single-digit track (1-9), enter 0 first. For example, to play track 5,
press 0, 5. You do not have to use the +10 button in search mode.
C
Using ∑ or w
∑
During playback, press
to skip the current track and
move to the next track. The track number will appear briefly
on the DVD/VCR display panel.
Or, during playback, press
the current track. Press
tracks. The track number will appear briefly on the DVD/VCR
display panel.
w
to return to the beginning of
w
repeatedly to go to previous
Helpful Hints
•
3 and 3 does not function
when playback is stopped.
• You cannot use 3 to go from
the last track on the disc to the
first track.
• Using 3 or 3 during Dual
Playback will only affect MP3
files. If you want to skip JPEG
files during Dual Playback, press
{ or B. Please note that
pressing 3 or 3 will affect
both MP3 and JPEG files if
SLIDE SHOW is set to MUSIC.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 36
36 Paused and Step-by-Step Playback, Resume On
Paused and Step-by-Step Playback
Press DVD to put the DVD/VCR in DVD mode.
OPEN/CLOSE
DVD light will appear on the front of the DVD/VCR.
1
4
2
5
8
0
3
6
1
2
During disc playback, press PAUSE k. Playback will
pause and the sound will be mute.
● Pressing PAUSE F once during Dual Playback will pause a
JPEG file only. Pressing PAUSE F one more time will
pause an MP3 playback.
TRACKING
TITLE
7
9
CLEAR
+10
VCR
SETUP
DVD
DISC
1
INPUT
MENU
When playing a DVD orVideo CD, press PAUSE
k
repeatedly to see the picture advance one frame
(or step) at a time. The sound will remain mute.
Pressing PAUSE k repeatedly during Audio CD, MP3,
3
4
OK
TM
Windows Media Audio or JPEG playback will have no
REW
PLAY
FFW
BACK
AUDIO
effect.
STOP
PAUSE
4
Press PLAY B to resume playback.
DISPLAY SUBTITLE ZOOM
2-3
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
SPEED
MODE TIMER SET
Resume On
Press DVD to put the DVD/VCR in DVD mode.
Helpful Hint
DVD light will appear on the front of the DVD/VCR.
1
2
• Set STILL MODE to FIELD in
the DISPLAY Menu if paused
images are blurry. Details are on
pages 50-51.
Press STOP C during playback. In a few seconds, the
following Resume message will appear on the TV screen.
For MP3,
Windows Media Audio
or JPEG:
TM
For DVD, VideoCD or
AudioCD:
OPEN/CLOSE
1
4
2
5
8
0
3
6
TRACKING
TITLE
7
9
Press PLAY B. In a few seconds, playback will resume
from the point at which it stopped last. You can Resume
Playing at the same point even if you turn off the
CLEAR
+10
3
VCR
SETUP
DVD
DVD/VCR, then turn it on again later. However, opening the
disc tray will cancel the Resume feature. Playback will start
at the beginning the next time you insert the disc.
DISC
1
3
INPUT
MENU
TM
OK
For MP3, Windows Media Audio and JPEG playback will
resume from the beginning of the current track.
To cancel Resume and start playing the disc from the
beginning, press STOP C again while playback is in the resume
REW
PLAY
FFW
BACK
AUDIO
TM
stop mode.As for MP3,Windows Media Audio and JPEG
STOP
PAUSE
playback, File List will appear when you cancel Resume.
Press PLAY B to start playing the disc from the beginning.
● To resume playback of aVideo CD with PBC function,
you have to cancel the PBC function first. See page 32 on
how to cancel the PBC function.
2
DISPLAY SUBTITLE ZOOM
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
SPEED
MODE TIMER SET
● The resume information will be cleared if you change the
parental level when the resume information is on.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 37
Repeat, A-B Repeat 37
Repeat
VCR
SETUP
DVD
1
DISC
Press DVD to put the DVD/VCR in DVD mode.
INPUT
MENU
DVD light will appear on the front of the DVD/VCR.
1
2
OK
During DVD,Video CD (without PBC),Audio CD, MP3,
TM
Windows Media Audio or JPEG playback, press REPEAT
REW
PLAY
FFW
BACK
AUDIO
repeatedly until the repeat mode you want appears on the
TV screen.
STOP
PAUSE
On a DVD, select CHAPTER, TITLE or OFF. On aVideo CD
(without PBC) and Audio CD, select TRACK, ALL (all tracks on
the disc) or OFF.
DISPLAY SUBTITLE ZOOM
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
TM
With MP3, Windows Media Audio or JPEG tracks, select
2
1
2
SPEED
MODE TIMER SET
TRACK, GROUP (all tracks in the current folder), ALL or OFF.
Selecting a new track, chapter or title will cancel Repeat Playback.
VCR
SETUP
DVD
DISC
INPUT
MENU
Example: Repeat a
DVD chapter
Example: Repeat a
Video CD or Audio CD track
OK
A-B Repeat
REW
PLAY
FFW
BACK
AUDIO
You can play a specified section of a DVD, Video CD or Audio CD
repeatedly. Follow these steps to set up the section you want to
repeat.
STOP
PAUSE
DISPLAY SUBTITLE ZOOM
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
1
3-4
SPEED
MODE TIMER SET
Press PLAY B to play the disc to the point at which
you want repeated playback to begin.
2
Helpful Hints
Press A-B REPEAT to set the starting point (A).
If you make a mistake, press CLEAR. This will erase point A
• Repeat Playback and A-B Repeat
are not available with some discs.
• The entire A-B Repeat section
must be within a single title or
track. If you do not enter Point B
before the end of the track or
title is reached, the end of the
track or title will become Point B
automatically.
3
and let you start over.
TV screen.
OFF will appear briefly on the
A –
• Point B must be later on the
disc than Point A.
Play the disc to the point at which you want
repeated playback to end, then press A-B REPEAT
again. Within a few seconds, the A-B section will begin to
play repeatedly.The segment will play over and over until
you cancel the A-B Repeat feature.
4
• A-B Repeat is not available with
MP3, Windows Media Audio
TM
and JPEG files.
• If you choose GROUP Repeat
during Dual Playback, all tracks
or files in each folder will play
repeatedly. For example if you
choose GROUP Repeat during
Dual Playback of MP3 folder A
and JPEG folder B, all MP3 files
in folder A and all JPEG files in
folder B will be repeated.
A – B
● To cancel A-B Repeat, press A-B REPEAT.
OFF will
appear on the TV screen. Regular playback will resume.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 38
38 Markers
Use Markers to remember your favorite places on a DVD, Video
CD (without PBC) or Audio CD.
● Before you begin, place the DVD/VCR in DVD mode. Press
DVD so DVD light appears on the front of the DVD/VCR.
OPEN/CLOSE
TRACKING
1
4
2
5
8
0
3
6
9
Play the disc to within 30 seconds of the point at
which you want to set the Marker. Press SEARCH
repeatedly until Marker Display appears.
1
7
CLEAR
TITLE
+10
VCR
SETUP
DVD
DISC
INPUT
MENU
2,4
OK
Example: DVD
3-4
1,4
REW
PLAY
FFW
BACK
AUDIO
Within 30 seconds, press s or B to select a Marker
(1-10). Make sure _ _ :_ _ :_ _ appears beneath the number.
STOP
PAUSE
2
3
DISPLAY SUBTITLE ZOOM
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
When the playback reaches the point you want to
remember, press OK. The title or track number and its
elapsed playing time will appear beneath the Markers.
A checkmark will replace the Marker number. The Marker
Display will disappear in about 30 seconds, or press
SPEED
MODE TIMER SET
BACK
to remove it.
Example: DVD
Example:Video CD
or Audio CD
To return to a Marker during playback, press
SEARCH repeatedly until Marker Display appears.
Press s or B to choose the Marker you want, then
press OK. Disc playback will continue from the marked
point.
4
Helpful Hints
• Opening the disc tray or turning
off the DVD/VCR will erase all
the Markers.
• To erase a single Marker, press
SEARCH repeatedly until
Marker Display appears. Press
s or B to select a Marker.
Press CLEAR. Press BACK
to remove the display.
• To erase all the Markers, press
SEARCH repeatedly until
Marker Display appears.
Press B to select AC, then
press OK. Press BACK
remove the display.
to
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 39
Subtitles, Camera Angles 39
Subtitles
VCR
SETUP
DVD
The DVD/VCR allows you to select a language for subtitles during
playback. You may select only languages that are available on the
DVD.
DISC
1
INPUT
MENU
OK
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
REW
PLAY
FFW
BACK
AUDIO
1
2
STOP
PAUSE
During playback, press SUBTITLE repeatedly to
select a subtitle language. The number of available
DISPLAY SUBTITLE ZOOM
languages appears at the right of the Subtitle Display. In the
example below, six languages are available ( /6).After a few
seconds, the subtitles will appear.
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
2
SPEED
MODE TIMER SET
Or, press SUBTITLE repeatedly to turn off subtitles.
When no subtitles are available,“NOT AVAILABLE”
appears at the right of the Subtitle Display.
VCR
SETUP
DVD
DISC
1
INPUT
MENU
Camera Angles
OK
Some DVDs contain scenes recorded from different angles or
perspectives. The perspective will not change if the DVD does not
contain sequences recorded from different camera angles.
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
DISPLAY SUBTITLE ZOOM
1
2
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
During playback, press ANGLE repeatedly to select
a different perspective. The number of available angles
SPEED
MODE TIMER SET
2
appears at the right of the Angle Display. In this example,
eight angles are available ( /8).
Helpful Hints
• With some DVDs, you must
select a subtitle language in
the Disc Menu.
• If the desired language does
not appear after pressing
SUBTITLE several times, the
disc does not have subtitles in
that language.
• Opening the disc tray will
cancel your Subtitle Setting.
• If the ANGLE ICON Setting is
ON,
will appear on the TV
screen when the current
portion of the disc has
multiple camera angles. To set
the ANGLE ICON ON or
OFF, see page 55-56.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 40
40 Audio Language, Stereo Sound Mode
Audio Language
VCR
SETUP
DVD
You can select a language for DVDs during playback if multiple
DISC
1
2
INPUT
MENU
languages are available.
OK
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
1
2
REW
PLAY
FFW
BACK
AUDIO
During DVD playback, press AUDIO repeatedly to
choose one of the available languages. Audio Display
STOP
PAUSE
appears at the top of the TV screen, and the new audio will
DISPLAY SUBTITLE ZOOM
be heard. The display will disappear after about 5 seconds.
The Audio Display may show the current settings for the
Dolby Digital or Multi-channel sound, if they are available on
the disc, and the sampling rate of the disc. The number of
available languages appears after the “ / ” at the right of the
display ( /3, for example).
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
SPEED
MODE TIMER SET
1.ENG Dolby D 3/2.1ch 48k/3
Example: English audio
Stereo Sound Mode
VCR
SETUP
DVD
Adjust Stereo Sound to determine whether you will hear the left
channel, the right channel or both channels (stereo) during Video
CD or Audio CD playback.
DISC
INPUT
MENU
OK
If you connected the DVD/VCR to a Stereo using the COAXIAL
DIGITAL AUDIO OUT jack as described on page 12, you cannot
adjust stereo sound mode.
REW
PLAY
FFW
BACK
AUDIO
Press AUDIO repeatedly duringVideo CD or Audio
STOP
PAUSE
CD playback to choose STEREO, L-ch or R-ch.
1
DISPLAY SUBTITLE ZOOM
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
1
STEREO
Both right and left channels
are heard (stereo).
SPEED
MODE TIMER SET
Helpful Hints
• If a language is not available
after pressing AUDIO several
times, the DVD does not have
that language.
L-ch
Only the left channel
is heard.
• Some DVDs only let you
change the language in the Disc
Menu.
• Audio languages may be
abbreviated (such as ENG for
English). Or, three dashes (- - -)
may appear instead of an
abbreviation.
R-ch
Only the right channel
is heard.
• Audio language selection cannot
be made during Rapid Play with
Voice. (Refer to page 33.)
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 41
Slow Motion, Zoom 41
Slow Motion
Press PAUSE F during DVD orVideo CD playback.
OPEN/CLOSE
1
4
2
5
8
0
3
6
9
1
2
Press FFW D or REW h. Slow Motion Playback will
TRACKING
begin. Press FFW D or REW h repeatedly during Slow
Motion Playback to play a DVD forward or backward at
approximately 1/16, 1/8 or 1/2 the normal speed. Reverse
slow motion is not available on aVideo CD.
7
CLEAR
TITLE
DVD
+10
VCR
SETUP
DISC
An
briefly on the TV screen to indicate Slow Forward Playback.
An 1 (1/16), 2 (1/8) or 3 (1/2) will indicate
Slow Reverse Playback.
1 (1/16),
2 (1/8) or
3 (1/2) will appear
INPUT
MENU
OK
3
REW
PLAY
FFW
2 2
STOP
PAUSE
BACK
AUDIO
DISPLAY SUBTITLE ZOOM
Example: Playing a DVD forward
at half the normal speed.
1
3
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
SPEED
MODE TIMER SET
Press PLAY B to return to normal playback.
3
Zoom
Zooming lets you enlarge the playback image of DVDs, Video CDs
or JPEG files, and lets you pan through the enlarged image.
VCR
SETUP
DVD
DISC
INPUT
MENU
Press ZOOM during playback or when playback is
OK
2
paused. The picture will appear twice as large. Press
1
ZOOM again to make the picture four times larger than
normal. Either x2 or x4 will appear beside
upper left corner of the TV screen.
icon in the
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
While the picture is enlarged, press K, L, s or B to
move the zoomed image up, down, left or right.
The gray box with an inner blue box that shows during
Zoomed Playback is the position guide. To remove it or
show it, press OK. The position of the blue box inside the
gray box indicates the position of the zoomed image within
the overall picture.
DISPLAY SUBTITLE ZOOM
2
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
1
SPEED
MODE TIMER SET
Helpful Hints
• Only slow forward is available
forVideo CDs.
• The sound will be mute during
Paused or Slow Motion
Playback.
● To return the picture to normal, press ZOOM
repeatedly.
• You cannot zoom a Disc Menu.
• The x4 zooming is not active
with some discs. Only x2
zooming is available forVideo
CDs and JPEG files.
• Position guide is not available
for JPEG playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 42
42 Program/Random Playback
Program Playback
You may determine the order in which Audio CD, MP3,
TM
Windows Media Audio or JPEG tracks will play.
OPEN/CLOSE
TRACKING
1
4
2
5
8
0
3
6
9
Random Playback
You may play the tracks of an Audio CD in Random order instead
of the order in which they are recorded (1, 2, 3...). You can also
TM
7
use this feature for MP3, Windows Media Audio and JPEG tracks.
CLEAR
TITLE
+10
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
1
VCR
SETUP
DVD
DISC
While playback is stopped, press MODE
repeatedly until the PROGRAM/RANDOM Screen
2 appears.
INPUT
MENU
OK
CD-DA
TOTAL 0:00:00
Disc name
T
REW
PLAY
FFW
BACK
AUDIO
1
2
3
4
5
6
7
3:30
4:30
5:00
3:10
5:10
1:30
2:30
T
T
T
T
STOP
PAUSE
T
T
OK
1/4
1/1
PLAY
PLAY
CLEAR
T
1
3:30
DISPLAY SUBTITLE ZOOM
Example: Audio CD
Example: MP3
(DUAL PLAYBACK - OFF)
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
SPEED
MODE TIMER SET
Program Playback
Press K or L to select a track you want to play,
then press OK.
Helpful Hints
• You cannot use the Number
buttons or SEARCH to select
another track during
3
CD-DA
TOTAL 1:03:30
T
1
2
3
4
5
6
7
3:30
4:30
5:00
3:10
5:10
1:30
2:30
T
T
T
T
T
T
T
1
5
3:30
5:10
T
T
10 4:20
11 3:00
12 3:20
17 4:10
22 2:50
2/3
T
T
T
T
Program/Random Playback. Use
∑ or w to select other tracks.
• You cannot combine Random
Playback with a program.
• You may play a program or a
track within a program
repeatedly. During Program
Playback, press REPEAT so ALL
(all tracks in the program) or
TRACK appears. The entire
program or the current track
will play over and over.
• You cannot alter a program
during playback.
• You can start Program Playback
only while in the PROGRAM
Screen.
OK
1/4
PLAY
CLEAR
T
1
3:30
Example: Audio CD
Press CLEAR to erase the last track in the program if you
make an error. Additional tracks may be on other screens.
Press L to go on to the next page, and press K to go back
to the previous page. Repeat this step until you have
selected all the tracks you wish to play in the program.
To see tracks in a program when there are more than 8
tracks, use ∑, w to see all the tracks. For MP3, Windows
TM
Media Audio or JPEG folders, press s or B to go to the
previous or next level of folders. Press TITLE to return to
the first item in the highest level.
Press PLAY B. The tracks will play once in the order you
set. Turning off the player or opening the disc tray will
4 erase the program.
• A program can have a maximum
of 99 tracks.
Random Playback
• To erase all tracks in the
program, select ALL CLEAR at
step 3.
While the RANDOM Screen appears, press
PLAY B. The tracks will play in random order. After all
3
the tracks play once, playback will stop.
• Program/Random Playback of
TM
MP3, Windows Media Audio
or JPEG tracks is not available
while DUAL PLAYBACK is ON.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 43
TM
MP3/Windows Media Audio/JPEG Playback 43
TM
The DVD/VCR will play MP3, Windows Media Audio and JPEG files
that you record and finalize on a CD-R (Compact Disc-Recordable)
or CD-RW (Compact Disc-Rewritable).
VCR
SETUP
DVD
1
2-3
These discs may contain pictures in a JPEG format or audio tracks in
DISC
TM
an MP3 orWindows Media Audio format. For example, you may have
INPUT
MENU
photographic film developed by a retailer that places the pictures on a
CD-R for you. These pictures may be in JPEG format. Or, you may copy
OK
TM
or download MP3/Windows Media Audio music files from certain
legal Internet sites, then copy those files onto a CD-R or CD-RW.
You cannot make or record such discs using this DVD/VCR. See your
computer manual for details on recording.
REW
PLAY
FFW
STOP
PAUSE
BACK
Keep these characteristics in mind when making discs you intend to
play on the DVD player of this DVD/VCR.
● Record MP3 files at a sampling frequency of 44.1 kHz or
48 kHz. Record in a constant bit rate between 32 kbps and 320
kbps.
Helpful Hints
TM
TM
● RecordWindows Media Audio tracks at a sampling frequency of
• MP3/Windows Media Audio
tracks and JPEG images are
known as files. Groups of files
are called folders.
44.1kHz or 48kHz. Record in a constant bit rate between 48 kbps
and 192kbps.
● When recording JPEG files, the size of the picture should be
between 32 x 32 and 6300 x 5100 dots.
• Folders have the
icon, MP3
files have the
icon,Windows
Press DVD to put the DVD/VCR in DVD mode.
TM
Media Audio files have the
icon, and JPEG files have the
icon.
DVD light will appear on the front of the DVD/VCR.
1
When you put a CD-R or CD-RW with MP3,
TM
• A maximum of 255 folders can
be recognized. A maximum of
999 files can be recognized.
• If you use PLAY B to close the
disc tray, playback starts
Windows Media Audio or JPEG files in the DVD/VCR, a File
2
List will appear automatically. Or if the disc is already in the
DVD/VCR and you want to call up the File List, press DISC
MENU. (If you use PLAY B to close the disc tray, Playback
starts automatically.) Press K or L to select a folder, MP3,
automatically. If you use
TM
Windows Media Audio or JPEG file.
OPEN/CLOSE A to close the
disc tray, you have to press
PLAY B to start playback.
• During playback, use the
Number buttons or ∑ and w
to change tracks. If a track is
not available,“X” will appear on
the TV screen, and playback may
resume at an incorrect track or
may continue with its current
track.
If you choose a track or file, press PLAY B or OK.
Starting with the track or file you selected, the tracks/files will
3
play in the order they were recorded, i.e. 1, 2, 3.
If you select a folder and press OK, the tracks or files
within that folder will appear. Press K or L to select
the track or file you want to play, then press PLAY
or OK.
B
● PressTITLE to return to the first item in the highest level of
folders or files.You also can press { or B to return to
previous or next levels.
• To see the File List during
playback, press DISC MENU.
The current track will be
highlighted.
● To change the Transition Mode for JPEG playback, press
MODE repeatedly until Transition Mode appears on top of
theTV screen during playback.Then press { , B or OK to
switch CUT IN/OUT and FADE IN/OUT. If you choose
CUT IN/OUT, the images will cut in and out sharply as
playback progresses. If you choose FADE IN/OUT, the
images will fade in and out as playback progresses.
● To change the size of the playback image, press MODE
repeatedly until SIZE MODE appears at the top of theTV
screen during playback. Then press { , B or OK to switch
NORMAL(100%) and SMALL(95%).
• Progressive JPEGs (JPEG files
saved in the progressive format)
will not play on this DVD/VCR.
• Copyright protected
TM
Windows Media Audio files
will not play on this DVD/VCR.
• High resolution JPEG files takes
longer to be displayed.
• SIZE MODE may have no effect
on some files (e.g. files with a
small picture size).
● Press MODE or BACK
to remove the display.
● During JPEG playback, press ANGLE to rotate a picture 90
degrees clockwise.
● To stop playback, press STOP C.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 44
TM
44 MP3/Windows Media Audio/JPEG Playback (cont’d)
Dual Playback
This feature lets you play MP3 and JPEG files simultaneously.
Available only when DUAL PLAYBACK is ON.
See pages 55-56 on how to set the DUAL PLAYBACK ON
or OFF.
1
2
3
VCR
SETUP
DVD
DISC
INPUT
MENU
OK
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
1
REW
PLAY
FFW
BACK
AUDIO
Press DISC MENU during MP3/JPEG playback.
A File List will appear.
STOP
PAUSE
2
DISPLAY SUBTITLE ZOOM
K
L
Press or to select a desired MP3/JPEG file
from the list and press PLAY B or OK.
● To stop playback, press STOP C.
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
3
SPEED
MODE TIMER SET
VCR
SETUP
DVD
Folder Playback
1
3
DISC
INPUT
MENU
You may select to play a folder containing MP3 and JPEG files.
Available only when DUAL PLAYBACK is ON.
See pages 55-56 on how to set the DUAL PLAYBACK ON
or OFF.
OK
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
DISPLAY SUBTITLE ZOOM
1
While playback is stopped, press MODE.
A Folder List will appear.
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
2
SPEED
MODE TIMER SET
Press K or L to select a folder, then press
2
PLAY B or OK.
3
● MP3 and JPEG files in the selected folder will play
Helpful Hints
• If you press PLAY B directly
simultaneously.
FOLDER LIST
DISC NAME
after you inserted a disc which
contains both MP3 and JPEG files
and if the DUAL PLAYBACK
Setting is ON, Dual Playback will
start automatically.
FOLDER
001
002
003
ALL
OK
PLAY
001
• You can not playWindows
Media Audio and JPEG files
TM
TM
● IfWindows Media Audio files are in the folder,
those files will be skipped during Folder Playback.
together at the same time. If you
choose aWindows Media Audio
TM
file during Dual Playback, only
TM
Windows Media Audio file will
play.
• Dual Playback may not function
properly if MP3 and JPEG files on
the disc interfere each other due
to the difference in their data size.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 45
On-Screen Displays 45
DVD Displays
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
OPEN/CLOSE
1
2
1
4
2
5
8
0
3
6
Press DISPLAY repeatedly to see the following
displays during DVD playback.
TRACKING
TITLE
7
9
CLEAR
7/49 0:01:46 - 0:03:27
+10
CH (chapter):
Current chapter number/
total chapters
Elapsed playing time
of the current chapter;
remaining playing time
of the current chapter
VCR
SETUP
DVD
DISC
1
3
INPUT
MENU
OK
1/2 0:00:00 - 1:23:45
TT (title):
Current title number/
total titles
Elapsed playing time of the
current title; remaining playing
time of the current title
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
BIT RATE: The amount of audio
and video data currently being read.
DISPLAY SUBTITLE ZOOM
C L0
Layer number, appears
only when playing a
two-layered disc.
L0: Layer 0 is playing
L1: Layer 1 is playing
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
2-3
SPEED
MODE TIMER SET
Current Repeat Setting, if active
C: Chapter Repeat
T: Title Repeat
A
B: A-B Repeat
Press DISPLAY repeatedly or press BACK
remove the display.
to
3
Video CD and Audio CD Displays
OPEN/CLOSE
3
1
4
2
5
8
0
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
6
1
2
TRACKING
7
9
Press DISPLAY repeatedly to see the following
displays during Video CD (without PBC) or Audio
CD playback.
CLEAR
TITLE
DVD
+10
VCR
SETUP
4/12 0:03:21 - 0:02:15
DISC
1
3
TR (track):
Current track number/
total tracks
INPUT
MENU
Elapsed playing time
of the current track;
remaining playing time
of the current track
OK
4/12 0:13:45 - 0:45:40
T
REW
PLAY
FFW
BACK
AUDIO
Current Repeat Setting, if active
T: Track Repeat
A: All Tracks Repeat
ALL:
Current track number/
total tracks
STOP
PAUSE
A
B: A-B Repeat
Elapsed playing time
of the entire disc;
remaining playing time of
the entire disc
DISPLAY SUBTITLE ZOOM
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
2-3
Press DISPLAY repeatedly or press BACK
remove the display.
to
SPEED
MODE TIMER SET
3
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 46
46 On-Screen Displays (cont’d)
TM
MP3/Windows Media Audio/JPEG Displays
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
OPEN/CLOSE
TRACKING
1
1
4
2
5
8
0
3
6
9
Press DISPLAY repeatedly until the current track
or file information appears.
2
7
TM
During JPEG playback
CLEAR
TITLE
During Windows Media Audio playback
+10
JPEG file name
track name
VCR
SETUP
DVD
DISC
1
3
INPUT
MENU
or
During MP3 playback
OK
title name
MP3 file name
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
● If Dual Playback is on, MP3
file name will be displayed
after JPEG file name.
DISPLAY SUBTITLE ZOOM
artist name
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
2-3
SPEED
MODE TIMER SET
T
2/25 0:01:15
Current Repeat Setting
TR (track):
Current track number/
total tracks
Elapsed playing time
of the current track
(for MP3/Windows Media
Audio only)
TM
Example: MP3 playback
The following may appear to indicate Repeat Playback.
T: The current track will play repeatedly.
G: Tracks in the current folder (group) will play repeatedly.
A: All tracks will play repeatedly.
PROGRAM
only during PROGRAM Playback
or
RANDOM
only during RANDOM Playback
or
FOLDER PLAYBACK
only during FOLDER Playback
● Program and Random Playback is available only when
DUAL PLAYBACK is OFF.
● Folder Playback is available only when DUAL PLAYBACK
is ON.
Helpful Hint
• For MP3 files recorded with
Variable Bit Rate (VBR), the
elapsed time displayed on the
screen may vary from the
actual elapsed time.
Press DISPLAY or BACK
to remove the display.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 47
Black Level,Virtual Surround 47
Black Level
Adjust Black Level to brighten the DVD orVideo CD picture.
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
1
Helpful Hints
During DVD orVideo CD playback, press
MODE so the Black Level icon shows in the top left
2 corner of the TV screen.
• Black Level is not available for
a PAL DVD.
• If you want to enjoy Dolby
Digital inVirtual Surround
through coaxial cable
connection, set Dolby Digital
to PCM.
• ForVideo CDs and Audio
CDs, you can adjustVirtual
Surround only if you set
Stereo Sound to STEREO.
Details are on page 40.
• The Black Level and theVirtual
Surround Settings will be saved
even if the player is turned off.
• When theVirtual Surround
function is active, 96 kHz
sound source will be down
sampled at 48 kHz, and output
as 48 kHz sound.
ON
While the Black Level icon is shown, press
s , B or OK repeatedly to choose ON or OFF.
3ON brightens the dark parts of the picture. OFF
shows the original picture as recorded.The icon will
disappear after about 10 seconds.
Virtual Surround
You can enjoy improved stereo sound when you play DVDs,
TM
Video CDs, Audio CDs, MP3 or Windows Media Audio
files recorded in Dolby Digital or Pulse Code Modulation
(PCM). Check the disc case for details on availability.
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
1
During disc playback, press MODE repeatedly
until theVirtual Surround icon appears in the top left
2 corner of the TV screen.
• The Black Level andVirtual
Surround Settings cannot be
used during x1.3 and x0.8
Rapid Play withVoice (refer to
page 33).
OFF
While theVirtual Surround icon is shown, press
s , B or OK to choose 1 (Natural), 2 (Emphasized)
3 or OFF.
The icon will disappear after about 10
seconds. The default setting is OFF.
Initializing
Use INITIALIZE to return all your DVD player’s Setup Menu
items (except PARENTAL) to their default settings.
OPEN/CLOSE
Press DVD to put the DVD/VCR in DVD mode.
1
4
2
5
8
0
3
6
DVD light will appear on the front of the DVD/VCR.
1
While playback is stopped, press SETUP.
The QUICK SETUP Screen appears.
TRACKING
TITLE
7
9
2
CLEAR
+10
QUICK SETUP
VCR
SETUP
DVD
2,4
3
OSD LANGUAGE
TV ASPECT
PROG. SCAN
DOLBY DIGITAL
ENGLISH
4:3 LETTER BOX
OFF
DISC
1
BITSTREAM
INPUT
MENU
OK
OK
Press s or B to select INIT. (INITIALIZE)
at the top of the menu, then press OK.
3
4
REW
PLAY
FFW
BACK
AUDIO
INITIALIZE
Initialize?
NO
STOP
PAUSE
YES
DISPLAY SUBTITLE ZOOM
OK
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
● Press K or L to selectYES.Then, press OK twice.To
cancel the process, select NO instead.
SPEED
MODE TIMER SET
Press SETUP to remove the menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 48
48 Language
You can select different languages for the Audio or Subtitles
of DVDs, as well as languages for DVD Disc Menus and the
Setup Menus of the DVD player.
OPEN/CLOSE
TRACKING
Press DVD to put the DVD/VCR in DVD mode.
1
4
2
5
8
0
3
6
9
DVD light will appear on the front of the DVD/VCR.
1
While playback is stopped, press SETUP.
The QUICK SETUP Screen appears.
7
CLEAR
TITLE
2
+10
Press s or B to select CUSTOM at the top of
the menu, then press OK.
VCR
SETUP
DVD
2
3-5
DISC
1
3
INPUT
MENU
OK
AUDIO
SUBTITLE
ORIGINAL
OFF
DISC MENU
OSD LANGUAGE
ENGLISH
ENGLISH
OK
REW
PLAY
FFW
STOP
PAUSE
BACK
With
(LANGUAGE) selected, press OK.
4
5
Helpful Hints
AUDIO
SUBTITLE
DISC MENU
ORIGINAL
OFF
ENGLISH
•
•
If the DVD’s default settings for
Audio and Subtitle are the same
language, the subtitles may not
show unless you turn them on.
Use the AUDIO and SUBTITLE
buttons to select Audio and
Subtitles available on the DVD.
Details are on pages 39-40.
If you set AUDIO to ORIGINAL,
the default setting of the DVD
Audio will play.
If you set OSD LANGUAGE to
FRANÇAIS (French) or
OSD LANGUAGE
ENGLISH
OK
Press K or L to select AUDIO, SUBTITLE, DISC
MENU or OSD LANGUAGE. Press OK. The
language options for the selected item will appear.
AUDIO: The DVD’s audio plays
•
•
LANGUAGE
AUDIO
ORIGINAL
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
in the selected language.
The default setting is
ORIGINAL.
OK
SWEDISH
ESPAÑOL (Spanish) and need
English: Follow steps 1-2. At step
3, the IDIOMA or LANGUE
Menu will appear. Press OK.
Press L to select LANGUE OSD
or IDIOMA PANT., then press
OK. Press K to select ENGLISH,
then press OK. The menus will
change to English. Press SETUP to
remove the menus.
SUBTITLE: Subtitles appear in
LANGUAGE
SUBTITLE
OFF
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
SWEDISH
the selected language.
The default setting is OFF.
OK
DISC MENU: A DVD’s Disc
Menu appears in the selected
language.
LANGUAGE
DISC MENU
ENGLISH
FRENCH
SPANISH
GERMAN
ITALIAN
•
You can change the OSD
OK
The default setting is ENGLISH.
LANGUAGE in the QUICK
SETUP Menu that appears when
you first press SETUP. With
QUICK selected, press OK.
OSD LANGUAGE will be
SWEDISH
DUTCH
OSD LANGUAGE: The DVD
player’s Setup Menu can be in
English, French or Spanish only.
The default setting is ENGLISH.
LANGUAGE
OSD LANGUAGE
ENGLISH
FRANÇAIS
ESPAÑOL
selected. Press OK. Press K or
L
OK
to choose a language, then press
OK. Press SETUP to remove the
menu.
•
The Language Settings may not
take effect until you restart disc
playback from the beginning.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 49
Language (cont’d) 49
Press K or L to select a language, then press OK.
The language lists may continue on multiple screens. Press
K or L to move to the other screens.
OPEN/CLOSE
6
7
1
4
2
5
8
0
3
6
9
● If you select OTHER for AUDIO, SUBTITLE, or
DISC MENU, press four Number buttons to
enter the code for the language you desire. Use one of
the Language Codes listed below. The language or
language code you select will appear in the Language
Menu beside AUDIO, SUBTITLE, or DISC MENU.
TRACKING
7
6
CLEAR
TITLE
DVD
+10
VCR
SETUP
7
6
DISC
INPUT
MENU
LANGUAGE
LANGUAGE CODE
Please enter a 4-digit language code.
OK
OK
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
● You can select other languages for AUDIO, SUBTITLE
and DISC MENU only if the language is available on the
disc. If the language you select is not recorded on the
DVD, changing these settings will have no effect.
DISPLAY SUBTITLE ZOOM
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
SPEED
MODE TIMER SET
Press SETUP to remove the menu.
Language Codes
A-B
English
5160 Kannada
5161 Kashmiri
5166 Kazakh
5760 Panjabi
5765 Pashto
5757 Persian
6247
T
Abkhazian
4748 Esperanto
4747 Estonian
6265 Tagalog
5247 Tajik
6258 Tamil
6658
Afar
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
4752
F-H
Kinyarwanda 6469 Polish
6563 Faroese
4759 Fiji
4764 Finnish
5471 French
4765 Frisian
5261 Kirghiz
5256 Kirundi
5255 Korean
5264 Kurdish
5271
5771 Portuguese 6266 Tatar
6460 Pushto
5761 Quechua
6265 Telugu
6367 Thai
5767 Rhaeto-Romance 6459 Tibetan
L-N
Romanian
5861 Russian
5847
6461 Tigrinya
6467 Tonga
Tsonga
Turkish
6559 Turkmen
6553 Twi
U-Z
6564 Ukrainian
Urdu
4771 Gaelic (Scots) 5350 Laothian
Azerbaijani 4772 Galician
5358 Latin
Bangla
4860 Georgian
4847 German
5167 Greek
5747 Latvian
5051 Lettish
5158 Lingala
5868
S
Bashkir
Basque
Bengali
Bhutani
Bihari
5868 Samoan
5860 Sangho
5866 Sanskrit
4860 Greenlandic 5758 Lithuanian
6547
5072 Guarani
4854 Gujarati
4855 Hausa
4864 Hebrew
4853 Hindi
5971 Hungarian
5360 Macedonian 5957 Serbian
5367 Malagasy
5447 Malay
6757
6764
6772
5953 Serbo-Croatian
5965
5958 Sesotho
5966 Setswana
5955 Shona
5964 Sindhi
5961 Singhalese
5960 Siswat
6047 Slovak
6051 Slovenian
Bislama
Breton
Bulgarian
Burmese
6554 Uzbek
5569 Malayalam
5455 Maltese
5467 Maori
I-K Marathi
6566 Vietnamese 6855
6660 Volapuk
6560 Welsh
6550 Wolof
6555 Xhosa
6565 Yiddish
6557 Yoruba
6558 Zulu
6561
6861
4971
6961
7054
5655
7161
7267
Byelorussian 4851
C-E
Icelandic
5565 Moldavian
5560 Mongolian
5547 Nauru
5551 Nepali
Cambodian 5759 Indonesian
Catalan
Chinese
Corsican
Croatian
Czech
4947 Interlingua
7254 Interlingue
4961 Inupiak
5464 Irish
4965 Italian
5047 Japanese
6058 Javanese
5557 Norwegian 6061 Somali
5347
O-R
Spanish
6149 Sundanese
6164 Swahili
5165
5566 Occitan
5647 Oriya
6567
Danish
Dutch
6569
5669 Oromo (Afan)6159 Swedish
6568
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 50
50 Display
You may adjust the TV Aspect ratio and still mode clarity, and
Progressive Scan compatibility.
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
OPEN/CLOSE
TRACKING
1
2
1
4
2
5
8
0
3
6
9
When playback is stopped, press SETUP.
The QUICK SETUP Screen will appear.
7
CLEAR
TITLE
+10
QUICK SETUP
OSD LANGUAGE
TV ASPECT
PROG. SCAN
DOLBY DIGITAL
ENGLISH
4:3 LETTER BOX
OFF
VCR
SETUP
DVD
2
BITSTREAM
DISC
1
OK
INPUT
MENU
OK
3-5
Press s or B to select CUSTOM at the top of
the menu, then press OK.
REW
PLAY
FFW
BACK
AUDIO
3
4
5
STOP
PAUSE
LANGUAGE
AUDIO
SUBTITLE
ORIGINAL
OFF
DISPLAY SUBTITLE ZOOM
DISC MENU
OSD LANGUAGE
ENGLISH
ENGLISH
OK
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
SPEED
MODE TIMER SET
Press s or B to select
press OK.
(DISPLAY), then
DISPLAY
TV ASPECT
STILL MODE
PROG. SCAN
4:3 LETTER BOX
AUTO
OFF
OK
Press K or L to select an item, then press OK.
● If you selectedTV ASPECT, press K or L to
select a setting, then press OK.
Choose 4:3 LETTER BOX if you want to see the
entire, widened picture with black bars at the top and
bottom of the screen. This looks like the picture you
see when watching movies in a theater. This setting is
possible only if the DVD was recorded in the
letterbox or widescreen format.
Helpful Hints
• Selecting a different TV
ASPECT Setting is only
Choose 4:3 PAN & SCAN for a full height picture,
with both sides trimmed. Some companies refer to
this as reformatting the picture to fit yourTV screen
and may call it the regular or normal format.
Choose 16:9WIDE if you connected a widescreen
TV to the DVD player.
effective if it is available on the
DVD. Check the DVD Disc
Menu or case for details.
• You also can adjust TV
ASPECT in the QUICK
SETUP Menu that appears
when you first press SETUP.
With QUICK selected, press
OK. Press L to select TV
ASPECT, then press OK. Press
K or L to choose a setting,
then press OK. Press SETUP
to remove the menu.
The default setting is 4:3 LETTER BOX.
DISPLAY
TV ASPECT
4:3 LETTER BOX
4:3 PAN
&
SCAN
16:9 WIDE
OK
• This unit does not set the TV
aspect automatically.
TV ASPECT
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 51
Display (cont’d) 51
● If you selected STILL MODE, press K or L to
select a setting, then press OK. This determines the
quality of an image in still mode.
If you select FIELD, still images will be stabilized but
coarse due to the small amount of data.
If you select FRAME, the images will be highly defined due
to the simultaneous output of two fields.
The default setting is AUTO.
OPEN/CLOSE
1
4
2
5
8
0
3
6
TRACKING
TITLE
7
9
CLEAR
+10
DISPLAY
VCR
SETUP
DVD
STILL MODE
AUTO
FIELD
6
DISC
FRAME
INPUT
MENU
OK
OK
STILL MODE
Press SETUP to remove the menu.
6
Progressive Scan
You may adjust the Progressive Scan compatibility.
Follow the steps 1-4 in the Display setup on page 50.
1
OPEN/CLOSE
Press K or L to select PROG. SCAN, then press OK
repeatedly to turn PROG. SCAN ON or OFF.
1
4
2
5
8
0
3
6
2 Choose ON if your TV has Progressive Scan and if the TV
is connected to the player’s COMPONENTVIDEO OUT
jacks. Choose OFF otherwise.
The default setting is OFF.
TRACKING
TITLE
7
9
CLEAR
+10
Press SETUP to remove the menu.
VCR
SETUP
DVD
3
● If PROG. SCAN is ON, this message appears:
3
DISC
INPUT
MENU
OK
2-3
REW
PLAY
FFW
Helpful Hints
Press K or L to make a selection, then press OK.
If you select NO, the menu disappears and
• You can set PROG. SCAN to
OFF either in the DISPLAY
Menu or by pressing and
holding PLAY B (DVD) on
the front of the player for
more than 5 seconds.
• You can adjust Progressive
Scan Setting in the QUICK
SETUP Menu that appears
when you first press SETUP.
With QUICK selected, press
OK. Press L to select PROG.
SCAN. Press OK to choose
OFF or ON. Press SETUP to
remove the menu.
PROG. SCAN is OFF. If you selectYES, this appears:
Confirm again to use progressive scan.
If Picture is good, Select “YES”.
NO
YES
SELECT: K /
L
SET:OK
Confirm your setting, then press OK. The menu will dis-
appear and the Progressive Scan function will be activated.
If you do not press any buttons for 15 seconds,
Progressive Scan will switch to OFF.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 52
52 Audio
Change Audio Settings based on other equipment you
connected to the DVD player or according to your disc
sound features. These setting only affect the Audio from the
DVD player of the DVD/VCR.
OPEN/CLOSE
TRACKING
Press DVD to put the DVD/VCR in DVD mode.
1
4
2
5
8
0
3
6
9
DVD light will appear on the front of the DVD/VCR.
1
While playback is stopped, press SETUP.
The QUICK SETUP Screen will appear.
7
CLEAR
TITLE
2
+10
QUICK SETUP
VCR
SETUP
DVD
2,7
3-6
OSD LANGUAGE
TV ASPECT
PROG. SCAN
DOLBY DIGITAL
ENGLISH
4:3 LETTER BOX
OFF
DISC
1
BITSTREAM
INPUT
MENU
OK
OK
Press s or B to select CUSTOM at the top of
the menu, then press OK.
3
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
LANGUAGE
AUDIO
SUBTITLE
ORIGINAL
OFF
DISC MENU
OSD LANGUAGE
ENGLISH
ENGLISH
DISPLAY SUBTITLE ZOOM
OK
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
SPEED
MODE TIMER SET
Press s or B to select (AUDIO) at the top
of the menu, then press OK.
4
5
Press K or L to select DRC, DOWN
SAMPLING, or DOLBY DIGITAL, then follow
step 6 accordingly.
AUDIO
DRC
DOWN SAMPLING ON
DOLBY DIGITAL
ON
BITSTREAM
OK
● If you selected DRC, press OK repeatedly to
turn Dynamic Range Control (DRC) ON or
OFF. Choosing ON compresses the range of volume
by suppressing loud sounds and raising low sounds.
DRC is available only on discs recorded in the
Dolby Digital format.
6
7
Helpful Hints
The default setting is ON.
● If you selected DOWN SAMPLING, press OK
repeatedly to choose ON or OFF. Choose ON
to down sample the 96 kHz sound source to 48 kHz.
Choose OFF to output the sound source without
any down sampling.
DOWN SAMPLING is available only when the player
is connected to a Stereo using the COAXIAL
DIGITAL AUDIO OUT jack as described on page 12.
The default setting is ON.
• Dolby Digital sound must be
available on the DVD.
• You can adjust DOLBY
DIGITAL in the QUICK
SETUP Menu that appears
when you first press SETUP.
With QUICK selected, press
OK. Press L to select DOLBY
DIGITAL. Press OK to choose
BITSTREAM or PCM. Press
SETUP to remove the menu.
• When you play a disc that has
copyright protection,
● If you selected DOLBY DIGITAL, press OK
repeatedly to select BITSTREAM or PCM.
Select BITSTREAM if you used the COAXIAL
DIGITAL AUDIO OUT jack to connect the DVD
player to a stereo that is Dolby Digital compatible.
Details are on page 12. Otherwise, choose PCM.
The default setting is BITSTREAM.
downsampling will be at 48
kHz, even if you set DOWN
SAMPLING to OFF.
Press SETUP to remove the menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 53
Parental Password 53
Parental Controls prevents viewing of DVDs that exceed your rating
limits. This feature will not limit viewing if the DVD is not rated or
coded. Check your DVDs and settings before letting children access
the DVD/VCR.You will need a password to change the Parental Settings
or to play a blocked disc. Follow these steps to change your password.
Press DVD to put the DVD/VCR in DVD mode.
OPEN/CLOSE
DVD light will appear on the front of the DVD/VCR.
1
1
4
2
5
8
0
3
6
9
While playback is stopped, press SETUP.
The QUICK SETUP Screen appears.
4,6
TRACKING
2
7
CLEAR
TITLE
DVD
+10
QUICK SETUP
OSD LANGUAGE
TV ASPECT
PROG. SCAN
DOLBY DIGITAL
ENGLISH
4:3 LETTER BOX
OFF
VCR
SETUP
2,7
3-6
BITSTREAM
OK
DISC
1
INPUT
MENU
OK
Press s or B to select CUSTOM, then press OK.
3
4
REW
PLAY
FFW
BACK
AUDIO
Press s or B to select
● If this is the first time you set a password, this menu will appear.
(PARENTAL), then press OK.
STOP
PAUSE
DISPLAY SUBTITLE ZOOM
PASSWORD
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
OK
SPEED
MODE TIMER SET
Press the Number buttons to enter a 4-digit password.
The password will appear on the screen. Write it down so you
will not forget it.
Press OK, and proceed to step 7.
● If you have set a password before, this menu will appear.
OK
Press the Number buttons to enter your current
4-digit password. Asterisks (*) will appear instead of your
password. This protects its identity. Press OK, and proceed to
step 7.
If you like to change the password, press K or L to select
PASSWORD CHANGE, then press OK.
Helpful Hints
5
• The default password is 4737. If
you forget your password, press
Number buttons 4, 7, 3, 7 at
step 4. You will be prompted to
enter a new 4-digit password.
Use the Number buttons to
enter a new 4-digit password,
then press OK. PARENTAL
LEVEL will reset to ALL. See
page 54 to reset PARENTAL
LEVEL as you desire.
PARENTAL
PARENTAL LEVEL ALL
PASSWORD CHANGE
OK
Press the Number buttons to enter a 4-digit password.
The password numbers will appear on the screen. Write down the
6 password so you will not forget it. Press OK. The previous menu
7
will reappear.
Press SETUP to remove the menu.
• A power failure will not erase
your password.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 54
54 Parental Levels
Follow these steps to set the rating level for your DVDs.
DVDs whose ratings exceed the level you set will not play.
Press DVD to put the DVD/VCR in DVD mode.
DVD light will appear on the front of the DVD/VCR.
1
While playback is stopped, press SETUP.
The QUICK SETUP Screen appears.
OPEN/CLOSE
TRACKING
1
4
2
5
8
0
3
6
9
2
5
QUICK SETUP
OSD LANGUAGE
TV ASPECT
PROG. SCAN
DOLBY DIGITAL
ENGLISH
4:3 LETTER BOX
OFF
7
BITSTREAM
CLEAR
TITLE
OK
+10
VCR
SETUP
DVD
2,8
DISC
Press s or B to select CUSTOM at the top of the
1
INPUT
MENU
menu, then press OK.
3
4
OK
3-4,
LANGUAGE
AUDIO
SUBTITLE
ORIGINAL
OFF
DISC MENU
OSD LANGUAGE
ENGLISH
ENGLISH
REW
PLAY
FFW
OK
6-7
STOP
PAUSE
BACK
Press s or B to select
the menu, then press OK.
(PARENTAL), at the top of
RATING EXPLANATIONS
• ALL : Parental Control is inactive; all discs
can play.
•
8 [ADULT]: DVD softwares of any grades
(adult/general/children) can be played back.
7 [NC-17]: No one under 17 admitted
6 [R]: Restricted; under 17 requires
accompanying parent or adult guardian
5 [PGR]: Parental Guidance Recommended
4 [PG13]: Unsuitable for children under 13
3 [PG]: Parental Guidance suggested
2 [G]: General Audience
OK
•
•
Press the Number buttons to enter your 4-digit
password.
•
•
•
•
•
5
6
Press K or L to select PARENTAL LEVEL, then
press OK.
1 [KID SAFE]: Suitable for children
PARENTAL
Helpful Hints
PARENTAL LEVEL ALL
PASSWORD CHANGE
OK
• When you try to play a DVD
whose rating exceeds the level
you set, an on-screen message
will indicate the DVD cannot
play. Remove the DVD, then set
PARENTAL LEVEL to ALL.
Reload the DVD and begin
playback. Some DVDs may let
you enter your 4-digit
password to begin playback.
Follow the on-screen messages
as prompted.
• You cannot use the default
password (4737) to play a DVD.
• The resume information will be
cleared if you change the
Press K or L to select a level, then press OK.
The rating levels continue on two menu screens. Press
K or L repeatedly to move to the next or previous screen
to find the rating level you want.
After making your selection, the previous menu will appear.
The level you selected will appear beside PARENTAL
LEVEL.
7
PARENTAL
PARENTAL LEVEL
ALL
8 [ADULT]
7 [NC-17]
6 [R]
5 [PGR]
4 [PG13]
3 [PG]
OK
parental level when the resume
information is on.
Press SETUP to remove the menu.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 55
Others 55
You may adjust the Angle Icon,Automatic Power Off,
Dual Playback and Slide Show Settings.
OPEN/CLOSE
Press DVD to put the DVD/VCR in DVD mode.
1
4
2
5
8
0
3
6
DVD light will appear on the front of the DVD/VCR.
1
TRACKING
TITLE
While playback is stopped, press SETUP.
The QUICK SETUP Screen appears.
7
9
CLEAR
2
+10
VCR
SETUP
DVD
2
3-5
DISC
1
QUICK SETUP
INPUT
MENU
OSD LANGUAGE
TV ASPECT
PROG. SCAN
DOLBY DIGITAL
ENGLISH
4:3 LETTER BOX
OFF
BITSTREAM
OK
OK
REW
PLAY
FFW
BACK
AUDIO
Press s or B to select CUSTOM at the top of
the menu, then press OK.
STOP
PAUSE
3
4
5
DISPLAY SUBTITLE ZOOM
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
LANGUAGE
AUDIO
SUBTITLE
DISC MENU
OSD LANGUAGE
ORIGINAL
OFF
ENGLISH
ENGLISH
SPEED
MODE TIMER SET
OK
Press s or B to select
press OK.
(OTHERS), then
OTHERS
ANGLE ICON
AUTO POWER OFF ON
DUAL PLAYBACK
SLIDE SHOW
ON
OFF
5sec
OK
Press K or L to select an item, then press OK.
●
If you selected ANGLE ICON, press OK
repeatedly to select ON or OFF. Choose ON to
see the Angle icon when multiple camera angles are
available during DVD playback. Details are on page 39.
Choose OFF to disable the Angle icon.
The default setting is ON.
OTHERS
ANGLE ICON
ON
AUTO POWER OFF ON
DUAL PLAYBACK OFF
SLIDE SHOW
5sec
OK
ANGLE ICON
Instructions continue on the next page.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 56
56 Others (cont’d)
Instructions continued from the previous page.
● If you selected AUTO POWER OFF, press OK
repeatedly to choose ON or OFF. Choose ON if you
want the player to turn off when there is no activity at
the player or its remote for 30 minutes.
OPEN/CLOSE
TRACKING
1
4
2
5
8
0
3
6
9
The default setting is ON.
7
CLEAR
TITLE
OTHERS
+10
ANGLE ICON
ON
AUTO POWER OFF ON
DUAL PLAYBACK OFF
VCR
SETUP
DVD
SLIDE SHOW
5sec
6
5
OK
DISC
INPUT
MENU
AUTO POWER OFF
OK
● If you selected DUAL PLAYBACK, press OK to
choose ON or OFF. This feature lets you play MP3 and
JPEG files simultaneously.
REW
PLAY
FFW
BACK
AUDIO
STOP
PAUSE
The default setting is OFF.
DISPLAY SUBTITLE ZOOM
OTHERS
ANGLE
REC
SEARCH REPEAT REPEAT
A-B
ANGLE ICON
AUTO POWER OFF ON
DUAL PLAYBACK OFF
ON
SPEED
MODE TIMER SET
SLIDE SHOW
5sec
OK
DUAL PLAYBACK
● If you selected SLIDE SHOW, press K or L to
choose 5sec, 10sec or MUSIC, then press OK. This
adjusts the playback speed of the SLIDE SHOW.
Choose 5 sec to display each image for 5 seconds.
Choose 10 sec to display each image for 10 seconds.
Choose MUSIC to display an image for each MP3 sound
file playback when DUAL PLAYBACK is ON.
The default setting is 5 sec.
OTHERS
SLIDE SHOW
5 sec
10 sec
MUSIC
OK
SLIDE SHOW
Press SETUP to remove the menu.
Helpful Hint
6
• When MUSIC is selected, the
playback speed of the SLIDE
SHOW will be set to 5
seconds under the conditions
listed below:
- When DUAL PLAYBACK is
OFF.
- When DUAL PLAYBACK is
ON, but only the JPEG files
are playing.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 57
Glossary 57
AUDIO IN/OUT Jacks: jacks on the front and back of the DVD/VCR that receive audio from another
source (IN) or send audio to another system (OUT). These jacks are red (right) and white (left).
COAXIAL DIGITAL AUDIO OUT Jack: sends digital audio to a Stereo, allowing you to adjust the
volume at the Stereo. This connection provides the Multi-channel surround sound as heard in movie
theaters. This jack on the DVD/VCR is black.
(
)
COMPONENTVIDEO OUT Y CB/PB
CR/PR Jacks: jacks on the back of the DVD/VCR that send
high-quality DVD video to a TV with ComponentVideo In jacks.This connection provides the best picture
quality for the DVD player of the DVD/VCR.
Dolby Digital: a surround sound system that provides Multi-channel sound as used in movie theaters.
Dubbing: copying a video cassette using anotherVCR.
HQ: high quality; a feature in theVCR circuitry which provides enhanced picture detail.
External Input Channel: the channel to which you set your DVD/VCR to receive the signal from the
external tuner. If you connected the external tuner to the AUDIO andVIDEO In jacks on the front of the
DVD/VCR, select L2. If you used the AUDIO andVIDEO IN jacks on the back of the DVD/VCR, select L1.
OTR: One-Touch Recording; a timed recording on theVCR that starts immediately and records for 30
minutes to 8 hours.
S-Video: produces a clearer DVD picture by sending separate signals for the luminance and the color.
S-Video only provides a picture for the DVD player of the DVD/VCR.
Tape Speeds: how fast the video cassette travels during a recording or playback. The faster the tape
speed, the better the picture quality. Slower tape speeds affect picture quality, but you can record more
onto a videotape.
• SP (Standard Playback) – fastest tape speed (recording time for a T120 tape is approximately 2 hours);
best picture quality.
• LP (Long Playback) – average tape speed. You cannot record in LP with thisVCR. If tapes were recorded
on a differentVCR in LP speed, the tape will play in LP on the DVD/VCR.
• SLP (Super Long Playback) – slowest tape speed (recording time for a T120 tape is approximately 6
hours). This speed allows the maximum recording on a single videotape.
VIDEO IN/OUT Jacks: jacks on the front and back of the DVD/VCR that receive video from another
source (IN) or send video to other video equipment or a TV (OUT). These jacks are yellow.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 58
58 Helpful Hints
If you are having problems with your product, check this list of problems and possible solutions before requesting
service. You may be able to solve the problem yourself.
If you need to call a customer service representative, please know the model number and serial number of your
product before you call. This information is displayed on the back of the product. Also, please take a moment to identify
the problem you are having, and be prepared to explain this to the representative. If you believe the representative will
need to help you with operations, please stay near the product. Our representatives will be happy to assist you.
The DVD/VCR has no power.
•
Make sure the power cord is connected completely to an AC (alternating current) outlet.
• Pressy to turn on the DVD/VCR. The DVD/VCR usually turns on in the mode it was in when you
turned it off. If there has been a power failure, it will turn on inVCR mode. Press DVD to put the unit in
DVD mode. PressVCR to put the unit inVCR mode. Or, press SOURCE to switch between the two
modes.
The remote control will not operate the DVD/VCR.
•
Aim the remote control directly at the remote sensor on the front of the DVD/VCR, not toward the TV. Details are
on page 18.
•
•
•
•
Remove all obstacles between the remote control and the DVD/VCR.
Inspect and/or replace the batteries in the remote control. Details are on page 13.
Use the remote control within 23 feet (7m) of the DVD/VCR.
When using the DVD player, press DVD, then try the other DVD feature buttons. Press DVD so DVD light appears
on the front of the DVD/VCR. This means the DVD/VCR is in DVD mode.
To use theVCR, pressVCR, then try the otherVCR feature buttons. PressVCR soVCR light appears on the front of
the DVD/VCR. This means the DVD/VCR is inVCR mode.
•
There is no picture in DVD mode.
•
Make sure the video cable is connected correctly. You may connect either the yellow video cable (supplied), an
optional S-Video cable, or optional component video cables. Make sure the TV is set to the correctVideo In channel
(usually the AUX IN, A/V IN, Auxiliary In, EXT or External In, ComponentVideo In or S-Video In channel). Check
your TV owner’s manual for details. Details are on page 8.
•
•
Insert a DVD that is playable on this DVD/VCR. Details are on page 7.
Make sure the DVD/VCR is in DVD mode. Press DVD or SOURCE so DVD light appears on the front of the
DVD/VCR.
Check if Progressive Scan is set correctly according to your connection to a TV. Details are on page 8. Enable
Progressive Scan at the DVD player only if you used the ComponentVideo connection to a TV that has Progressive
Scan. Details are on pages 8, 10 and 51.
•
Disc cannot be played.
•
•
Insert a playable disc. Details are on page 7.
Place the disc correctly in the disc tray. If the disc is one-sided, place the disc in the tray with the label facing up. If the
disc is two-sided, make sure the label of the side you want to play is facing up.
Clean the disc. Make sure the disc is not scratched or warped.
•
•
•
Cancel the Parental Controls, enter the password or change the control level. Details are on pages 53-54.
Make sure the disc is labeled for use in Region 1 or ALL regions and is NTSC or PAL compatible. Details are on page 7
.
There is no sound.
•
Connect the audio cable firmly. Make sure the cables are connected to the AUDIO IN jacks on the TV or Stereo.
Details are on pages 9-12.
•
•
Check the Audio Settings of the DVD player. Details are on page 52.
Check the Audio Settings of the DVD. For example, you may have selected “soundtrack” playback or an unavailable
Sound Setting (such as Dolby Digital). Details are on pages 40 and 52. Try other sound options provided in the DVD
Disc Menu.
The picture is distorted.
•
Connect the DVD/VCR directly to the TV. Details are on pages 8-12. Do not connect the DVD/VCR to aVCR, then
connect theVCR to the TV. Copyright protection systems in theVCR could distort the picture playing on the
DVD/VCR.
•
•
There are some cases where a disc or videotape picture may be distorted slightly because of the quality in which it
was recorded. This is not a malfunction of the DVD/VCR.
Make sure the disc is compatible with the DVD player of the DVD/VCR. Details are on page 7.
• In case of picture problems with 525 (480) progressive scan output, it is recommended that the user switch the
connection to the ‘standard definition’ output. If there are questions regarding your TV set compatibility with this
525p (480p) DVD player, please contact our customer service center.
•
If your TV is not PAL compatible, DVDs recorded in the PAL color system may play only in black and white, the
picture may roll continuously, or the picture may appear distorted.
You cannot change the camera angle of a DVD.
•
The DVD might not contain segments recorded from different camera angles. See if multiple angles are available by
referring to the disc case or DVD Disc Menu. Details are on page 39.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 59
Helpful Hints (cont’d) 59
You cannot change the audio or subtitle language of a DVD.
•
The DVD does not contain audio or subtitles in the desired language. Not all DVDs contain audio or subtitles in
multiple languages. See if other languages are available by referring to the disc case or DVD Disc Menu. Details are on
pages 39-40.
An X appears in the top right corner of theTV screen when you try a DVD feature.
•
The operation is not available at the current time or the feature is not available on the disc. Some features are only
available during playback. Others can be accessed only if playback is stopped. Try stopping or playing the disc, then try
the feature again.
The DVD/VCR switches from DVD mode toVCR mode after 30 minutes of no activity.
•
When AUTO POWER OFF is set to ON, the DVD/VCR switches itself from DVD mode toVCR mode if disc
playback stops for more than 30 minutes and you press no buttons on the remote or the DVD/VCR. Details are on
pages 55-56. This prevents possible damage to your TV’s picture tube that can occur if a still image is left on too long.
A screen saver appears on theTV screen during DVD mode.
•
The screen saver appears when you leave the DVD/VCR in stop mode for about five minutes to protect the TV
screen from burn-in.
You want to use the DVD player during aVCR Timer Recording or while “ ” appears on the display
panel.
• Pressy to turn on the DVD/VCR. Press DVD to choose DVD mode, then continue with other DVD
features as described in this manual.
A maximum of 999 MP3/Windows Media Audio/JPEG files can be recognized.
TM
Power Failure
•
Clock and language setting will be lost after 30 seconds of power failure. See pages 19-20 to set up the clock and
language again.
TheVCR will not record aTV program.
•
•
•
•
•
This DVD/VCR does not have a tuner to receive TV broadcasting.
You must connect this DVD/VCR to an external tuner to record TV programs.
Check the connections between the DVD/VCR and the external tuner. Details are on page 9.
Put the DVD/VCR inVCR mode. PressVCR or SOURCE soVCR light appears on the front of the DVD/VCR.
Make sure the video cassette has a record tab. Details are on page 21.
TheVCR will not perform a Timer Recording.
•
•
Make sure the recording start and stop times are set correctly. Details are on pages 24-25.
Make sure a tape is in theVCR and the tape has a record tab. Details are on page 21. If, after programming a Timer
Recording, you press TIMER SET without putting a tape in the DVD/VCR,“ ” will blink on the display panel.
If the record tab on a tape is missing, the DVD/VCR will eject the tape.“ ” will blink.
Press TIMER SET to put the DVD/VCR in standby mode for the Timer Recording.
Make sure theVCR clock is set. Details are on page 19.
TheVCR may not perform or continue a Timer Recording if the power fails.
Finish programming a Timer Recording at least 5 minutes before it is set to begin.
12 p.m. is noon; 12 a.m. is midnight.
•
•
•
•
•
•
There is no picture or the picture is noisy or has streaks during video cassette playback.
•
•
•
•
Put the DVD/VCR inVCR mode. PressVCR or SOURCE soVCR light appears on the front of the DVD/VCR.
Select the correctVideo In channel at the TV. Details are on page 8.
Adjust the tracking. Details are on page 31.
TVs placed too close to the DVD/VCR can cause interference during tape playback. Move the DVD/VCR away from the TV
.
TV programs cannot be watched normally.
•
Check the connections between the DVD/VCR and the external tuner. Details are on page 9.
You cannot insert a video cassette.
•
•
•
•
Insert the tape, window side up, with the record tab facing you.
Make sure that there is no tape on theVCR by pressing STOP/EJECT C A on the front of the DVD/VCR.
Gently push on the center of the tape when putting it in theVCR. Never force the tape into theVCR.
If a Timer Recording is set, you cannot insert a tape without a record tab.
You cannot remove the tape.
•
•
Make sure the power plug is completely connected to a power outlet.
If a Timer Recording has been set, press TIMER SET on the remote control or STOP/EJECT C A on the front panel to
cancel the timer standby mode temporarily.“ ” will disappear from the display panel.Then, press STOP/EJECT C A
on the front of the DVD/VCR to eject the tape. Insert another tape and press TIMER SET to reset the Timer
Recording.
• Unplug the DVD/VCR power cord for 5 minutes. Then, plug in the power cord again and press y on the
DVD/VCR. Press STOP/EJECT C A on the DVD/VCR 3 to 5 times. If the tape still does not eject, you
may need to have an authorized servicer remove the tape.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 60
60 Helpful Hints (cont’d)
DVD/VCR ejects the tape when you press REC I orTIMER SET.
•
Make sure the tape has a record tab. Details are on page 21.
Hi-Fi Stereo Sound
•
•
During playback, Hi-Fi audio may normally revert to normal audio when you adjust tracking.
When connecting the DVD/VCR to a TV with the red and white audio cable, you will only get stereo sound if you
connect the DVD/VCR AUDIO OUT jacks on the DVD/VCR to the AUDIO IN jacks on your TV, and if the TV is on
its Audio/Video In channel. See your TV owner’s manual for details.
•
•
When you connect the DVD/VCR AUDIO OUT jacks on the DVD/VCR to the AUDIO IN jacks on your TV, the
stereo light on the TV might not glow.
Only tapes recorded in Hi-Fi audio will play in Hi-Fi audio. Tapes recorded in normal audio will play in monaural
(single-channel) audio.
Cleaning the video heads
•
Your DVD/VCR automatically cleans the video heads of theVCR each time you insert a tape. However, the heads
may become dirty. If so, have an authorized servicer clean the video heads. Eventually, the heads may need to be
replaced.
The playback picture is too dim, too bright or fluctuates in brightness.
•
Some programs may be broadcast with copyright protection technology in order to protect the rights of copyright
owners. This technology is used on programs that are recorded on video cassettes or DVDs, as well as some
programs broadcast by antenna/cable/satellite television channels. Programs broadcast with copyright protection may
not record clearly. Likewise, if you play a tape that is a recording of a copyright protected program, the picture may
not be clear. Tapes of copyright protected programs may have a picture that is dark or dim, or the brightness of the
picture may fluctuate. Therefore, avoid recording or playing copies of copyright protected programs.
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 61
Care and Maintenance 61
Cleaning the DVD/VCR
• Wipe the front panel and other exterior surfaces of the DVD/VCR with a soft, slightly damp cloth.
• Never use a solvent, thinner, benzene or alcohol to clean the DVD/VCR. Do not spray insecticide liquid
near the DVD/VCR. Such chemicals may discolor the surface or damage the DVD/VCR.
Cleaning a Disc
• Use a soft, dry cloth to wipe the disc.
• Wipe the disc in a straight line from the center to the edge. Never wipe the disc in a circular motion.
• Do not use detergent or abrasive cleaning agents.
• Handle the discs so fingerprints and dust do not adhere to the discs.
• Always store the disc in its protective case when it is not in use.
Checking the Laser
• If the DVD/VCR does not operate as described in this manual, the DVD player’s laser may be dirty.
Consult an Authorized Service Center for inspection and cleaning of the laser.
Caring forVideo Cassettes
• Use only cassettes with the
mark.
• Remove any light adhesive stick-on notes from the video cassette before putting the cassette in theVCR.
Removable labels can jam theVCR.
Caring for theVCR’sVideo Heads
• Periodic maintenance is required to maintain your DVD/VCR’s excellent performance. TheVCR has an
Automatic Head Cleaner. However, the video heads will require replacement eventually. Only an
authorized service center should perform this service.
Specifications
VCRVideo Heads
Power Consumption
Power on: 21 W
4 heads - Hi-Fi
Power off: 3.8 W
DVD Color System
NTSC
OperatingTemperature
41°F (5°C) to 104°F (40°C)
Frequency Response
DVD (linear sound):
20 Hz to 22 kHz (sample rate: 48 kHz)
20 Hz to 44 kHz (sample rate: 96 kHz)
Audio CD: 20 Hz to 20 kHz
Relative Humidity
30% to 80%
Dimensions
17.1” (W) x 3.7” (H) x 9.2” (D)
(435mm x 94mm x 233mm)
Signal-to-Noise Ratio
Audio CD: 100 dB JEITIA
(Japan Electronics and InformationTechnology Industries
Association)
Weight
5.8 lbs. (2.6 kg.)
NOTE: Designs and specifications are subject to change
without notice.
Dynamic Range
DVD (linear sound): 90 dB
Audio CD: 85 dB (JEITIA)
Total Distortion Factor
Audio CD: 0.03% (JEITIA)
DVD: 0.03%
Wow and Flutter
Below the measurement limitation
( 0.001% W PEAK) (JEITIA)
Power Requirement
120V AC +/- 10%, 60 Hz +/- 0.5%
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 5:35 PM Page 62
62 Limited Warranty
90 DAY LIMITED WARRANTY
WARRANTY COVERAGE:
This warranty obligation is limited to the terms set forth
below.
a part that has been modified without written permission,
or (d) if any serial number has been removed or defaced,
or (e) product, accessories or consumables sold “AS IS”
without warranty of any kind by including refurbished Philips
product sold “AS IS” by some retailers.
WHO IS COVERED:
This product is warranted to the original purchaser or the per-
son receiving the product as a gift against defects in materials
and workmanship as based on the date of original purchase
(“Warranty Period”) from an Authorized Dealer. The original
sales receipt showing the product name and the purchase date
from an authorized retailer is considered such proof.
This Limited Warranty does not cover:
Shipping charges to return defective product.
•
•
Labor charges for installation or setup of the product, adjust-
ment of customer controls on the product, and installation or
repair of antenna/signal source systems outside of the product.
Product repair and/or part replacement because of improper
installation or maintenance, connections to improper voltage
supply, power line surge, lightning damage, retained images or
screen markings resulting from viewing fixed stationary con-
tent for extended periods, product cosmetic appearance items
due to normal wear and tear, unauthorized repair or other
cause not within the control of the company.
•
WHAT IS COVERED:
This warranty covers new products if a defect in material
or workmanship occurs and a valid claim is received within
the Warranty Period. At its option, the company will either (1)
repair the product at no charge, using new or refurbished
replacement parts, or (2) exchange the product with a product
Damage or claims for products not being available for use, or
for lost data or lost software.
that is new or which has been manufactured from new, or ser- •
viceable used parts and is at least functionally equivalent or most
Damage from mishandled shipments or transit accidents when
returning product.
comparable to the original product in current inventory, or (3)
refund the original purchase price of the product.
•
•
A product that requires modification or adaptation to enable
it to operate in any country other than the country for which
it was designed, manufactured, approved and/or authorized, or
repair of products damaged by these modifications.
A product used for commercial or institutional purposes
(including but not limited to rental purposes).
The Company warrants replacement products or parts provided
under this warranty against defects in materials and workmanship
from the date of the replacement or repair for ninety (90) days
or for the remaining portion of the original product’s warranty,
•
whichever provides longer coverage for you. When a product or
part is exchanged, any replacement item becomes your property
and the replaced item becomes the company’s property. When •a
refund is given, your product becomes the company’s property.
Product lost in shipment and no signature verification receipt
can be provided.
Failure to operate per Owner’s Manual.
Note: Any product sold and identified as refurbished or
renewed carries a ninety (90) day limited warranty.
•
TO OBTAIN ASSISTANCE IN THE U.S.A., PUERTO
RICO, OR U.S. VIRGIN ISLANDS…
Contact Philips Customer Care Center at:
1-866-771-4018
Replacement product can only be sent if all warranty
requirements are met. Failure to follow all requirements
can result in delay.
TO OBTAIN ASSISTANCE IN CANADA…
1-800-661-6162 (French Speaking)
WHAT IS NOT COVERED - EXCLUSIONS AND LIMI-
TATIONS:
1-866-771-4018 (English or Spanish Speaking)
This Limited Warranty applies only to the new products that
can be identified by the trademark, trade name, or logo affixed
to it. This Limited Warranty does not apply to any non-Philips
hardware product or any software, even if packaged or sold
with the product. Non-Philips manufacturers, suppliers, or
publishers may provide a separate warranty for their own
products packaged with the bundled product.
REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS
WARRANTY IS THE EXCLUSIVE REMEDY FOR THE CON-
SUMER. PHILIPS SHALL NOT BE LIABLE FOR ANY INCIDEN-
TAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF
ANY EXPRESS OR IMPLIED WARRANTY ON THIS PROD-
UCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE
LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT
IS LIMITED IN DURATION TO THE DURATION OF THIS
WARRANTY.
The Company is not liable for any damage to or loss of any
programs, data, or other information stored on any media
contained within the product, or any non-Philips product or part
not covered by this warranty. Recovery or reinstallation of
programs, data or other information is not covered under this
Limited Warranty.
Some states do not allow the exclusions or limitation of inciden-
tal or consequential damages, or allow limitations on how long an
implied warranty lasts, so the above limitations or exclusions may
not apply to you.
This warranty does not apply (a) to damage caused by
accident, abuse, misuse, neglect, misapplication, or non-
Philips product, (b) to damage caused by service performed
by anyone other than an Authorized Service Location, (c) to
product or
This warranty gives you specific legal rights. You may have other rights which vary from state/province to state/province.
P&F USA, INC
P.O.Box 672768 Marietta, Georgia 30006
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_EN2.qxd 09.1.23 2:43 PM Page 63
Information Index 63
ac power cord . . . . . . . . . . . . . . . . .18 index search . . . . . . . . . . . . . . . . . . .30 slp . . . . . . . . . . . . . . . . . . . . . . . . . .57
angle button . . . . . . . . . . . . . . . .18, 39 initializing . . . . . . . . . . . . . . . . . . . . .47 source button . . . . . . . . . . . . . . . . .18
angle icon . . . . . . . . . . . . . . .39, 55-56 input button . . . . . . . . . . . . . . . .18, 21 sp . . . . . . . . . . . . . . . . . . . . . . . . . . .57
arrow buttons . . . . . . . . . . . . . . . . .18
specifications . . . . . . . . . . . . . . . . . .61
audio button . . . . . . . . . . . . . . . .18, 40 jpeg display . . . . . . . . . . . . . . . . . . . .46 speed button . . . . . . . . . . . . . . .18, 21
audio in/out jacks . . . . . . . .9-12, 18, 23 jpeg playback . . . . . . . . . . . . . . . .43-44 standard playback . . . . . . . . . . . . . . .57
audio settings . . . . . . . . . . . . . . . . . .52
standby-on y button . . . . . . . . . . .18
auto power off . . . . . . . . . . . . . .55-56 language (dvd) . . . . . . . . . . . . . . .48-49 status display (vcr) . . . . . . . . . . . . . .20
auto repeat . . . . . . . . . . . . . . . . . . .29 language (vcr) . . . . . . . . . . . . . . . . . .20 step-by-step playback . . . . . . . . . . . .36
automatic
line input mode . . . . . . . . . . . . . . . .24 stereo sound . . . . . . . . . . . . . . . . . .40
tape playback . . . . . . . . . . . . . . . .31 long playback . . . . . . . . . . . . . . . . . .57 stereoTV hookups . . . . . . . . . . .11-12
tape rewind, eject . . . . . . . . . . . . .31 lp . . . . . . . . . . . . . . . . . . . . . . . . . . .57 still mode . . . . . . . . . . . . . . . . . .50-51
a-b repeat . . . . . . . . . . . . . . . . . . . .37
still picture . . . . . . . . . . . . . . . . .31, 36
a-b repeat button . . . . . . . . . . . .18, 37 markers . . . . . . . . . . . . . . . . . . . . . .38 stop C button . . . . . . . . . . . . . . . . .18
menus . . . . . . . . . . . . . . . . . . . . . .6, 32 stop/eject CA (vcr) button . . . . . . .18
back button . . . . . . . . . . . . . . . . . . .18 mode button . . . . . . . . . . . . . . .18, 42 subtitle button . . . . . . . . . . . . . .18, 39
batteries . . . . . . . . . . . . . . . . . . . . . .13 mp3 display . . . . . . . . . . . . . . . . . . .46 super high speed searching . . . . . . .31
bit-rate display . . . . . . . . . . . . . . . . .45 mp3 playback . . . . . . . . . . . . . . .43-44 super long playback . . . . . . . . . . . . .57
black level . . . . . . . . . . . . . . . . . . . .47
s-video out jack . . . . . . . . . . . . .10, 18
number buttons . . . . . . . . . . . . . . . .18
camera angle . . . . . . . . . . . . . . . . . .39
table of contents . . . . . . . . . . . . . . . .5
cassette compartment . . . . . . . . . . .17 ok button . . . . . . . . . . . . . . . . . . . . .18 tape
chapters . . . . . . . . . . . . . . . . . . . . . .34 on-screen status displays (vcr) . . . . .20
clear button . . . . . . . . . . . . . . . .18, 19 one-touch recording . . . . . . . . . . . .22
clock . . . . . . . . . . . . . . . . . . . . . . . .22 open/close A button . . . . . . . . .16, 18
duplication . . . . . . . . . . . . . . . . . .23
eject . . . . . . . . . . . . . . . . .18, 31, 59
speed . . . . . . . . . . . . . . . . . . . . . .57
coaxial digital audio out jack . . .12, 18 osd language . . . . . . . . . . . . . . . .48-49 time search . . . . . . . . . . . . . . . . . . .30
component video out jacks . . . .10, 18
timer recording
canceling . . . . . . . . . . . . . . . . . . .25
setting . . . . . . . . . . . . . . . . . . .24-25
connections . . . . . . . . . . . . . . . . .8-12 parental . . . . . . . . . . . . . . . . . . . .53-54
contents, table of . . . . . . . . . . . . . . . .5 parental password . . . . . . . . . . . . . .53
controls
pause button . . . . . . . . . .18, 31, 36, 41 timer set button . . . . . . . . . . . . .18, 25
dvd/vcr . . . . . . . . . . . . . . . . . . . . .18 play button . . . . . . . . . . . . . .15-16, 18 title button . . . . . . . . . . . . . . . . .18, 32
remote . . . . . . . . . . . . . . . . . . . . .18 playing discs . . . . . . . . . . . . . . . . . . .16 titles . . . . . . . . . . . . . . . . . . . . . . . . .32
copyright protection . . . . . . . .4, 23, 60 playing tapes . . . . . . . . . . . . . . . . . . .15 tracking . . . . . . . . . . . . . . . . . . . . . .31
counter . . . . . . . . . . . . . . . . . . . .20, 29 power
tracks . . . . . . . . . . . . . . . . . . . . . . . .35
cord . . . . . . . . . . . . . . . . . . . . . . .18 tv aspect . . . . . . . . . . . . . . . . . . .50-51
disc menu button . . . . . . . . . . . .18, 32
on light . . . . . . . . . . . . . . . . . . . . .18 tv hookups . . . . . . . . . . . . . . . . . .8-12
disc menus . . . . . . . . . . . . . .32, 48-49 program . . . . . . . . . . . . . . . . . . . . . .42
disc tray . . . . . . . . . . . . . . . . . . . . . .17 progressive scan . . . . . . . . . . . . . . . .51 vcr
display button . . . . . . . . .18, 20, 45-46
button . . . . . . . . . . . . . . . . . . . . .18
display messages . . . . . . . . . . . . . . . .17 quick setup . . . . . . . . . . . . . . . . .48-52
light . . . . . . . . . . . . . . . . . . . . . . .17
display panel . . . . . . . . . . . . . . . . . . .17
video in/out jacks . . . . . . . . . . .9-12, 18
displays . . . . . . . . . . . . . . . . .20, 45-46 random . . . . . . . . . . . . . . . . . . . . . .42 virtual surround . . . . . . . . . . . . . . . .47
dolby digital . . . . . . . . . . . . . . . . . . .52 rapid play with voice . . . . . . . . . . . .33
down sampling . . . . . . . . . . . . . . . . .52 rear panel . . . . . . . . . . . . . . . . . . . . .18 warranty . . . . . . . . . . . . . . . . . . . . .62
TM
drc (dynamic range control) . . . . . .52 rec I button . . . . . . . . . . . . .18, 21-22 Windows Media Audio display . . . . . .46
TM
dual playback . . . . . . . . . . . . . . . . . .44 recording
Windows Media Audio playback . . . .43
duplication (dvd to videotape) . . . . .28
duplication (tape) . . . . . . . . . . . . . . .23
dvd button . . . . . . . . . . . . . . . . . . . .18
basic . . . . . . . . . . . . . . . . . . . . . . .21
prevention . . . . . . . . . . . . . . . . . .21 zoom . . . . . . . . . . . . . . . . . . . . . . . .41
timer . . . . . . . . . . . . . . . . . . . .24-25 zoom button . . . . . . . . . . . . . . .18, 41
dvd light . . . . . . . . . . . . . . . . . . . . . .17 remote control
batteries . . . . . . . . . . . . . . . . . . . .13
buttons . . . . . . . . . . . . . . . . . . . . .18
ejecting a tape . . . . . . . . . . . .15, 31, 60
sensor . . . . . . . . . . . . . . . . . . . . .18
fast forward . . . . . . . . . . . . . . . .31, 33 repeat button . . . . . . . . . . . . . . .18, 37
ffw D button . . . . . . . . . . . . . . . . .18 repeat (discs) . . . . . . . . . . . . . . . . . .37
folder playback . . . . . . . . . . . . . . . . .44 repeat (tape) . . . . . . . . . . . . . . . . . .29
front panel . . . . . . . . . . . . . . . . . . . .17 rerecording . . . . . . . . . . . . . . . . . . .23
resume on . . . . . . . . . . . . . . . . . . . .36
glossary . . . . . . . . . . . . . . . . . . . . . .57 reverse searching . . . . . . . . . . . .31, 33
rew E button . . . . . . . . . . .18, 31, 33
head cleaner . . . . . . . . . . . . . . . . . . .60
helpful hints . . . . . . . . . . . . . . . .58-60 safety precautions . . . . . . . . . . . . . . .4
hi-fi stereo sound . . . . . . . . . . . . . . .32 satellite link . . . . . . . . . . . . . . . . .26-27
hookups
search button . . . . . . . . . .18, 30, 34-35
cable box/satellite receiver . . . . . .9 searching . . . . . . . . . . . . . . . . . . .31, 33
component video . . . . . . . . . . . . .10 sensor (remote) . . . . . . . . . . . . . . . .18
S-video . . . . . . . . . . . . . . . . . . . . .10 setup button . . . . . . . . . . . . . . . . . .18
stereo . . . . . . . . . . . . . . . . . . .11-12 skip ∑, skip w . . . . . . . . . . . . .18, 35
tv . . . . . . . . . . . . . . . . . . . . . . .9-12 slow motion . . . . . . . . . . . . . . . .31, 41
This owner’s manual is made of recyclable
materials. Remember to recycle!
Download from Www.Somanuals.com. All Manuals Search And Download.
E8E21UD_SP2 09.1.23 3:53 PM Page 64
P&F USA, Inc.
P.O. Box 672768 Marietta, Georgia 30006
Meet Philips at the Internet
DVP3345V
CLASS 1
LASER PRODUCT
Printed In China
JpnHF-0910/F7-3
1VMN27293 ★★★★★
E8E21UD
Download from Www.Somanuals.com. All Manuals Search And Download.
|