Always there to help you
Register your product and get support at
HTL5145B
Question?
Contact
Philips
User manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1 Important
Safety
2
2
3
3
3
3
8 Troubleshooting
15
Care for your product
Care of the environment
Compliance
Help and support
2 Your SoundBar
Main unit
4
4
4
5
6
Remote control
Connectors
Wireless subwoofer
3 Connect and set up
Place subwoofer
6
6
7
7
8
Pair up with the subwoofer
Connect toTV
Connect digital devices through HDMI
Connect audio fromTV and other devices 8
4 Use your SoundBar
Adjust the volume
9
9
Choose your sound
Play audio through Bluetooth
Connect Bluetooth via NFC
MP3 player
USB storage devices
Auto standby
9
10
10
11
11
11
11
12
Set display brightness
Apply factory settings
5 Update software
Check software version
Update software via USB
12
12
12
6 Wall mount
13
14
7
Product specifications
EN
1
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
If the product is transported in
temperatures below 5°C, unpack the
product and wait until its temperature
matches room temperature before
connecting it to the power outlet.
Parts of this product can be made of
glass. Handle with care to avoid injury and
damage.
1 Important
Read and understand all instructions before you
use your product. If damage is caused by failure
to follow instructions, the warranty does not
apply.
Risk of overheating!
•
Never install this product in a confined
space.Always leave a space of at least four
inches around the product for ventilation.
Ensure curtains or other objects never
cover the ventilation slots on the product.
Safety
Risk of electric shock or fire!
•
Never expose the product and accessories
to rain or water. Never place liquid
containers, such as vases, near the product.
If liquids are spilt on or into the product,
disconnect it from the power outlet
immediately. Contact Consumer Care to
have the product checked before use.
Never place the product and accessories
near naked flames or other heat sources,
including direct sunlight.
Risk of contamination!
•
Do not mix batteries (old and new or
carbon and alkaine, etc.).
Danger of explosion if batteries are
incorrectly replaced. Replace only with the
same or equivalent type.
Remove batteries if they are exhausted or
if the remote control is not to be used for
a long time.
Batteries contain chemical substances, they
should be disposed of properly.
•
•
•
•
•
•
Never insert objects into the ventilation
slots or other openings on the product.
Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
Risk of swallowing batteries!
•
The product/remote control may contain
a coin/button type battery, which can be
swallowed. Keep the battery out of reach
of children at all times! If swallowed, the
battery can cause serious injury or death.
Severe internal burns can occur within two
hours of ingestion.
•
•
Disconnect the product from the power
outlet before lightning storms.
When you disconnect the power cord,
always pull the plug, never the cable.
Risk of short circuit or fire!
•
•
If you suspect that a battery has been
swallowed or placed inside any part of the
body, seek immediate medical attention.
When you change the batteries, always
keep all new and used batteries out of
reach of children. Ensure that the battery
compartment is completely secure after
you replace the battery.
If the battery compartment cannot be
completely secured, discontinue use of the
product. Keep out of reach of children and
contact the manufacturer.
•
Before you connect the product to the
power outlet, ensure that the power
voltage matches the value printed on the
back or bottom of the product. Never
connect the product to the power outlet if
the voltage is different.
Risk of injury or damage to this product!
•
Never place the product or any objects
on power cords or on other electrical
equipment.
•
2
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the disposable batteries
To remove the disposable batteries, see battery
installation section.
This is CLASS II apparatus with double
insulation, and no protective earth provided.
Compliance
Care for your product
Use only microfiber cloth to clean the product.
This product complies with the radio
interference requirements of the European
Community.
Hereby,WOOX Innovations declares that
this product is in compliance with the
essential requirements and other relevant
provisions of Directive 1999/5/EC.You
can find the Declaration of Conformity on
Care of the environment
Disposal of your old product and battery
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Help and support
For extensive online support, visit
•
•
•
download the user manual and the quick
start guide
watch video tutorials (available only for
selected models)
find answers to frequently answered
questions (FAQs)
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
•
•
email us a question
chat with our support representative.
This symbol means that the product contains
batteries covered by European Directive
2013/56/EU which cannot be disposed of with
normal household waste.
Inform yourself about the local separate
collection system for electrical and electronic
products and batteries. Follow local rules and
never dispose of the product and batteries
with normal household waste. Correct disposal
of old products and batteries helps prevent
negative consequences for the environment and
human health.
Follow the instructions on the website to select
your language, and then enter your product
model number.
Alternatively, you can contact Consumer Care
in your country. Before you contact, note down
the model number and serial number of your
product.You can find this information on the
back or bottom of your product.
EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Your SoundBar
Remote control
This section includes an overview of the
remote control.
Congratulations on your purchase, and
welcome to Philips!To fully benefit from
the support that Philips offers, register your
a
b
Main unit
This section includes an overview of the main
unit.
c
d
e
m
f
g
h
i
a
b
c
d
e
a
(Standby-On/Standby indicator)
j
k
l
•
•
Switch the SoundBar on or to standby.
When the SoundBar is in standby, the
standby indicator turns red.
b SOURCE
Select an input source for the SoundBar.
c Display panel
d +/- (Volume)
a
(Standby-On)
Switch the SoundBar on or to standby.
Increase or decrease volume.
e NFC tag
b Source buttons
Tap the NFC-enabled device on the tag for
Bluetooth connection.
•
HDMI ARC: Switch your source to
HDMI ARC connection.
•
HDMI IN: Switch your source to the
HDMI IN connection.
•
•
•
: Switch to Bluetooth mode.
USB: Switch to USB mode.
OPTICAL: Switch your audio source
to the optical connection.
•
AUX: Switch your audio source to
the AUDIO IN or AUX connection
(3.5mm jack).
4
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
c
d
/
(Previous/Next)
Connectors
Skip to the previous or next track in USB
mode.
This section includes an overview of the
connectors available on your SoundBar.
(Play/Pause)
Start, pause or resume play in USB
mode.
•
f
e BASS +/-
Increase or decrease bass.
f Volume control
•
+/-: Increase or decrease volume.
•
: Mute or restore volume.
a
b
e
d
g SOUND
Select a sound mode.
c
h SURROUND ON/OFF
Select surround or stereo sound.
i AUTOVOL ON/OFF
a DC IN
Turn auto volume on or off.
Connect to the power supply.
j NIGHT ON/OFF
b AUX IN
Turn night mode on or off.
Connect to an audio output on a device
via AUDIO IN or AUX source (by pressing
repeatedly AUX on the remote control).
k AUDIO SYNC +/-
Increase or decrease audio delay.
l DIM
c OPTICAL IN
Set the brightness of SoundBar display
panel.
Connect to an optical audio output on the
TV or a digital device.
m TREBLE +/-
d HDMI OUT (ARC) -TOTV
Increase or decrease treble.
Connect to the HDMI input on theTV.
e HDMI IN
Connect to the HDMI output on a digital
device.
f
•
Audio input from a USB storage
device.
•
•
Upgrade software of this product.
Charge a USB device.
EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Connect and set
up
Wireless subwoofer
The SoundBar comes with a wireless subwoofer.
This section helps you connect your SoundBar
to aTV and other devices, and then set it up.
For information about the basic connections of
your SoundBar and accessories, see the quick
start guide.
a
b
Note
• For identification and supply ratings, see the type plate
at the back or bottom of the product.
• Before you make or change any connections, make sure
that all devices are disconnected from the power outlet.
Place subwoofer
c
See the quick start guide on how to place the
subwoofer.
a Subwoofer indicator
Note
•
When the power is turned on, the
• If you place the subwoofer vertically, install the supplied
foot stand to prevent instability of the subwoofer.
indicator lights up.
•
During wireless pairing between the
subwoofer and the main unit, the
indicator blinks white quickly.
When the pairing succeeds, the
indicator lights up white.
When the pairing fails, the indicator
blinks white slowly.
When wireless connection is
disconnected for one minute, the
indicator turns off.
Place the subwoofer at least 1 meter (3 feet)
away from your SoundBar, and ten centimeters
away from the wall.
For best results, place your subwoofer as shown
below.
•
•
•
b CONNECT (connect)
Press to to enter the pairing mode for the
subwoofer.
c AC MAINS~
Connect to the power supply.
6
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect toTV
Connect your SoundBar to aTV.You can listen
to audio fromTV programs through your
SoundBar. Use the best quality connection
available on your SoundBar andTV.
Connect toTV through HDMI (ARC)
Your SoundBar supports HDMI with Audio
Return Channel (ARC). If yourTV is HDMI ARC
compliant, you can hear theTV audio through
your SoundBar by using a single HDMI cable.
TV
Pair up with the subwoofer
The wireless subwoofer automatically pairs
up with the SoundBar for wireless connection
when you turn on the SoundBar and the
subwoofer.
If no audio from the wireless subwoofer can be
heard, manually pair up the subwoofer.
1 Using a High Speed HDMI cable, connect
the HDMI OUT (ARC)-TOTV connector
on your SoundBar to the HDMI ARC
connector on theTV.
•
The HDMI ARC connector on theTV
might be labeled differently. For details,
see theTV user manual.
1 Turn on the SoundBar and the subwoofer.
» If the connection to the SoundBar is
lost, the indicator on the subwoofer
blinks white slowly.
2 On yourTV, turn on HDMI-CEC
operations. For details, see theTV user
manual.
2
Press the CONNECT (connect) button on
the subwoofer to enter the pairing mode.
» The indicator on the subwoofer blinks
white quickly.
Note
• If yourTV has a DVI connector, you can use an HDMI/
DVI adapter to connect toTV. However, some of the
features may not be available.
3 On the remote control, within six seconds
press twice then BASS + once, and then
hold down SURROUND ON.
» If the pairing succeeds, the indicator on
the subwoofer lights up white.
» If the pairing fails, the indicator on the
subwoofer blinks white slowly.
4 If the pairing fails, repeat the steps above.
EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Option 1: Connect audio through a
digital optical cable
Connect digital devices
through HDMI
Best quality audio
Connect a digital device such as a set-top box,
DVD/Blu-ray player, or games console to your
SoundBar through a single HDMI connection.
When you connect the devices in this way and
play a file or game, the
TV
•
video is automatically displayed on your
TV, and
•
audio is automatically played on your
SoundBar.
1 Using an optical cable, connect the
OPTICAL IN connector on your
SoundBar to the OPTICAL OUT
connector on theTV or other device.
1 Using a High Speed HDMI cable, connect
the HDMI OUT connector on your digital
device to the HDMI IN on your SoundBar.
•
The digital optical connector might be
labeled SPDIF or SPDIF OUT.
2 Connect your SoundBar toTV through
HDMI OUT (ARC).
•
If theTV is not HDMI CEC compliant,
select the correct video input on your
TV.
Option 2: Connect audio through
analog audio cables
Basic quality audio
3 On the connected device, turn on HDMI-
CEC operations. For details, see the user
manual of the device.
Connect audio fromTV and
other devices
Play audio fromTV or other devices through
your Soundbar speakers.
Use the best quality connection available on
yourTV, Soundbar, and other devices.
1 Using an analog cable, connect the AUX
IN (3.5mm jack) on your SoundBar to the
AUDIO OUT connectors (red and white)
on theTV or other device.
Note
2 Press repeatedly AUX on the remote
control until AUX is displayed on the
display panel.
8
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
•
BRIGHT: Spice up your dull movies
and music with added sound effects.
CLEAR: Hear every detail in your
music and clear voices in your movies.
WARM: Experience spoken words and
music vocals in comfort.
4 Use your
SoundBar
This section helps you use the SoundBar to play
audio from connected devices.
PERSONAL: Personalize the sound
based on your preferences.
Before you start
•
Make the necessary connections described
in the quick start guide and the user
manual.
Switch the SoundBar to the correct source
for other devices.
Surround sound mode
Experience an immersive audio experience with
surround sound modes.
•
1 Press SURROUND ON/OFF to turn
surround mode on or off.
•
On: Create a surround listening
experience.
Adjust the volume
•
Off:Two-channel stereo sound. Ideal
for listening to music.
1 Press +/- (Volume) to increase or decrease
a volume level.
Equalizer
•
•
To mute sound, press (Mute).
To restore the sound, press (Mute)
again or press +/- (Volume).
Change the high frequency (treble) and low
frequency (bass) settings of the SoundBar.
1 Press TREBLE +/- or BASS +/- to change
the frequency.
Choose your sound
Synchronize video and sound
This section helps you choose the ideal sound
for your video or music.
If the audio and video are not synchronized,
delay the audio to match the video.
1 Press AUDIO SYNC +/- to synchronize
Sound mode
the audio with the video.
Select predefined sound modes to suit your
video or music.
Auto volume
1 Press SOUND to select a sound option
from the display panel.
Turn the auto volume on to keep the volume
constant when you switch to a different source.
•
AUTO:Automatically select a sound
setting based on the sound stream.
POWERFUL: Enjoy thrilling arcade
sounds, ideal for action-packed videos
and loud parties.
1 Press AUTOVOL ON/OFF to turn auto
•
volume on or off.
•
BALANCED: Experience the original
sound of your movies and music,
without added sound effects.
EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Wait until the SoundBar beeps.
» When the Bluetooth connection
succeeds, BT is displayed on the display
panel.
Night mode
For quiet listening, night mode decreases the
volume of loud sounds when audio is played.
Night mode is only available for Dolby Digital
soundtracks.
» If the connection fails, BT on the
display panel blinks continuously.
1 Press NIGHT ON/OFF to turn night
4
Select and play audio files or music on
your Bluetooth device.
mode on or off.
•
During play, if a call is coming, music
play is paused. Play resumes when the
call ends (this feature is dependent on
the connected mobile device).
Note
• If auto volume is set to turned on, you cannot enable
the night mode.
•
If your Bluetooth device supports
AVRCP profile, on the remote control
you can press
/
to skip to a track,
or press
to pause/resume play.
Play audio through Bluetooth
5 To exit Bluetooth, select other source.
•
When your switch back to Bluetooth
mode, Bluetooth connection remains
active.
Through Bluetooth, connect the SoundBar with
your Bluetooth device (such as an iPad, iPhone,
iPod touch,Android phone, or laptop), and then
you can listen to the audio files stored on the
device through your SoundBar speakers.
Note
• The music streaming may be interrupted by obstacles
between the device and SoundBar, such as wall, metallic
casing that covers the device, or other devices nearby
that operate in the same frequency.
• If you want to connect your SoundBar with another
Bluetooth device, press and hold on the remote
control to disconnect the currently connected
Bluetooth device.
What you need
•
A Bluetooth device which supports
Bluetooth profile A2DP, AVRCP and with
Bluetooth version as 3.0 + EDR.
•
The maximum operational range between
the SoundBar and a Bluetooth device is
approximately 10 meters (30 feet).
1 Press on the remote control to switch
the SoundBar to Bluetooth mode.
» BT is displayed on the display panel,
blinking.
Connect Bluetooth via NFC
NFC (Near Field Communication) is a
technology that enables short-range wireless
communication between NFC-enabled devices,
such as mobile phones.
2 On the Bluetooth device, switch on
Bluetooth, search for and select PHILIPS
HTL5145 to start connection (see the
user manual of the Bluetooth device on
how to enable Bluetooth).
What you need
» During connection, BT on the display
panel blinks.
•
•
A Bluetooth device with NFC function.
For pairing, tap the NFC device on the
NFC tag of the SoundBar.
1 Enable NFC on the Bluetooth device (see
the device' s user manual for details).
10 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Tap the NFC device onto the NFC tag of
1 Connect a USB storage device to this
the SoundBar until the SoundBar beeps.
product.
•
For first time connection, on some
mobile devices prompt for pair-up
appears, select "YES" for connection.
2 Press USB on the remote control.
3 Use the remote control to control play.
» When the Bluetooth connection
succeeds, BT is displayed on the display
panel.
Button Action
Start, pause or resume play.
/
Skip to the previous or next track.
During USB play, press repeatedly to
select a repeat or shuffle mode, or
turn off a play mode.
» If the connection fails, BT on the
USB
display panel blinks continuously.
3
Select and play audio files or music on
your NFC device.
•
To break the connection, tap again the
NFC device onto the NFC tag on the
SoundBar.
Note
• This product supports WMA files which are converted
via Windows Media Player (WMA files converted via
other file format converters may not work).
• If a USB storage device has a large media library, it takes
some time to load those contents.
• This product may not be compatible with certain types
of USB storage device.
• If you use a USB extension cable, USB HUB, or USB
multi-reader, the USB storage device may not be
recognized.
MP3 player
Connect your MP3 player to play your audio
files or music.
• Digital camera PTP and MTP protocols are not
What you need
supported.
•
•
An MP3 player.
A 3.5mm stereo audio cable.
• Do not remove the USB storage device while it is
being read.
• DRM-protected music files (MP3,WMA) are not
1 Using the 3.5mm stereo audio cable,
connect the MP3 player to the AUX IN
connector on your SoundBar.
supported.
• Support a USB port: 5V
1A.
2 Press repeatedly AUX on the remote
control until AUDIO IN is displayed on the
display panel.
Auto standby
3 Press the buttons on the MP3 player to
When playing media from a connected device,
the SoundBar automatically switches to standby
after 15 minutes of button inactivity and no
audio/video play from a connected device.
select and play audio files or music.
USB storage devices
Enjoy audio on a USB storage device, such as an
MP3 player and USB flash memory, etc.
Set display brightness
What you need
You can press DIM repeatedly to select a
different brightness level of the display panel on
this product.
•
A USB storage device that is formatted for
FAT or NTFS file systems, and complies
with the Mass Storage Class.
•
An MP3 or WMA file on a USB storage
device
EN 11
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Update software
Apply factory settings
You can reset this product to the default
settings programmed at the factory.
To get the best features and support, update
your product with the latest software.
1 In any source mode, on the remote control
press Volume -, BASS -, and TREBLE - in
sequence within three seconds.
Check software version
» When the factory settings restore is
complete, the product automatically
switches off and restarts.
In HDMI ARC source, on the remote control
press TREBLE -, BASS -, and Volume - in
sequence.
Update software via USB
1 Check the latest software version on
•
Search for your model and click on
"Software and drivers".
2 Download the software into a USB storage
device.
a Unzip the download if zipped, and
make sure that the unzipped file is
named "HTL5145.BIN".
b Put the "HTL5145.BIN" file in the
root directory.
3 Connect the USB storage device to the
(USB) connector on this product.
4 Switch this product to HDMI ARC source.
5 On the remote control, within six seconds
press twice then Volume + once, and
then hold down SURROUND ON.
» "UPGRADE" (upgrade) blinks on the
display panel.
6 Press to start the upgrade.
» Then "UPGRADE" (upgrade) is
displayed on the display panel.
7 Wait until the upgrade is completed.
» If the upgrade is complete, this product
automatically turns off and on again.
12 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Caution
6 Wall mount
• Do not turn off the power or remove the USB storage
device when the software update is in progress because
you might damage this product.
Note
• Improper wall mounting may result in accident, injury or
damage. If you have any query, contact Consumer Care
in your country.
• Before wall mounting, make sure the wall can support
the weight of your SoundBar.
• Before wall mount, you need not remove the four
rubber feet at the bottom of the SoundBar, otherwise
the rubber feet cannot be fixed back.
Screw length/diameter
Depending on the type of wall mounting your
SoundBar, make sure that you use screws of a
suitable length and diameter.
3.5-4mm
4mm
> 25mm
See the illustration in the quick start guide on
how to wall mount the SoundBar.
1) Drill two holes on the wall.
2) Secure the dowels and screws in the holes.
3) Hang the SoundBar on the fastening screws.
EN 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
7 Product
specifications
• This product supports WMA files which are converted
via Windows Media Player (WMA files converted via
other file format converters may not work).
Note
Bluetooth
• Specifications and design are subject to change without
notice.
•
•
Bluetooth profiles:A2DP, AVRCP
Bluetooth version: 3.0 + EDR
Amplifier
Main unit
•
Total output power: 320W RMS
(+/- 0.5 dB, 10%THD)
Frequency response: 20 Hz-20 kHz / ±3 dB
Signal-to-noise ratio: > 65 dB (CCIR) /
(A-weighted)
•
Power supply:
•
Model (Philips branded AC power
adapter): DYS602-210309W;AS650-
210-AA309
•
•
•
•
Input: 100-240V~, 50/60 Hz 1.5 A
Output: 21V , 3.09A
•
Input sensitivity:
•
•
AUX: 500 mV
AUDIO IN: 200 mV
•
•
Standby power consumption: ≤ 0.5 W
Speaker impedance
•
•
Woofer: 8 ohm
tweeter: 8 ohm
Audio
•
Speaker drivers: 4 x (90mm/3.5" x
34mm/1.3") woofer + 2 x 31mm/1.2"
tweeter
•
S/PDIF Digital audio input:
Optical:TOSLINK
•
•
•
Dimensions (WxHxD):
1045 x 49 x 72 mm
Weight: 2.0 kg
USB
•
•
Compatibility: Hi-Speed USB (2.0)
Class support: USB Mass Storage Class
(MSC)
Subwoofer
•
•
•
File system: FAT16, FAT32, NTFS
Supports MP3 and WMA file formats
Sampling frequency:
•
•
•
•
•
•
Power supply: 220-240V~, 50-60 Hz
Power consumption: 60 W
Standby power consumption: ≤ 0.5 W
Impedance: 2 x 6 ohm
Speaker drivers: 2 x 165 mm (6.5”) woofer
Dimensions (W x H x D):
730 x 83 x 330 mm
•
MP3: 8 kHz, 11 kHz, 12 kHz, 16 kHz,
22 kHz, 24 kHz, 32 kHz, 44.1 kHz,
48 kHz
•
WMA: 44.1 kHz, 48 kHz
•
•
Constant bit rate:
•
Weight: 7.4 kg
•
•
MP3: 8 kbps-320 kbps
WMA: 32 kbps-192 kbps
Remote control batteries
Version:
WMA:V7,V8,V9
•
•
2 x AAA-R03-1.5V
14 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby information
8 Troubleshooting
•
When the product remains inactive for
15 minutes, it automatically switches to
standby or networked standby.
Warning
•
•
The power consumption in standby or
networked standby is less than 0.5W.
To deactivate Bluetooth connection, press
and hold the Bluetooth button on the
remote control.
To activate Bluetooth connection, enable
Bluetooth connection on your Bluetooth
device, or enable Bluetooth connection via
the NFC tag (if available).
• Risk of electric shock. Never remove the casing of the
product.
To keep the warranty valid, never try to repair
the product yourself.
If you have problems using this product, check
the following points before you request service.
If you still have a problem, get support at
•
Main unit
The buttons on the SoundBar do not work.
•
Disconnect the SoundBar from the power
supply for a few minutes, then reconnect.
Sound
No sound from SoundBar speakers.
•
Connect the audio cable from your
SoundBar to yourTV or other devices.
However, you do not need a separate
audio connection when:
•
the SoundBar andTV are connected
through HDMI ARC connection, or
a device is connected to the HDMI IN
connector on your SoundBar.
•
•
•
Reset your SoundBar to its factory settings.
On the remote control, select the correct
audio input.
•
Make sure that the SoundBar is not muted.
No sound from the wireless subwoofer.
•
the SoundBar (see 'Pair up with the
Distorted sound or echo.
•
If you play audio from theTV through the
SoundBar, make sure that theTV is muted.
EN 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio and video are not synchronized.
•
For some Bluetooth, the Bluetooth
connection can be deactivated
•
Press AUDIO SYNC +/- to synchronize
the audio with the video.
automatically to save power.This does not
indicate any malfunction of the SoundBar.
Error message is displayed on the display
panel.
NFC
•
•
•
When "ERROR" is displayed, it indicates
that an input audio format is not
supported.
When "USB ERROR" is displayed, it
indicates that the connected USB device is
not supported.
When "HDMI ARC" blinks, it indicates
that the connectedTV is not HDMI ARC
compliant or an unsupported audio format
is detected.
A device cannot connect with the SoundBar
via NFC.
•
Make sure that the device is supported by
NFC.
•
Make sure that NFC is enabled on the
device (see the device' s user manual for
details).
•
For pairing, tap the NFC device on the
NFC tag of the SoundBar.
Bluetooth
A device cannot connect with the SoundBar.
•
The device does not support the
compatible profiles required for the
SoundBar.
•
You have not enabled the Bluetooth
function of the device. See the user manual
of the device on how to enable the
function.
•
•
The device is not correctly connected.
Connect the device correctly.
The SoundBar is already connected with
another Bluetooth device. Disconnect the
connected device, then try again.
Quality of audio play from a connected
Bluetooth device is poor.
•
The Bluetooth reception is poor. Move the
device closer to the SoundBar, or remove
any obstacle between the device and the
SoundBar.
The connected Bluetooth device connects and
disconnects constantly.
•
The Bluetooth reception is poor. Move the
device closer to the SoundBar, or remove
any obstacle between the device and the
SoundBar.
•
Turn off Wi-Fi function on the Bluetooth
device to avoid interference.
16 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
© 2013 CSR plc and its group companies.
The aptX® mark and the aptX logo are
trade marks of CSR plc or one of its group
companies and may be registered in one or
more jurisdictions.
Manufactured under license under U.S.
Patent Nos: 5,956,674; 5,974,380; 6,487,535
& other U.S. and worldwide patents issued
& pending. DTS, the Symbol, & DTS and the
Symbol together are registered trademarks
& DTS Digital Surround and the DTS logos
are trademarks of DTS, Inc. Product includes
software. DTS, Inc.All Rights Reserved.
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI Logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth
SIG, Inc. and any use of such marks by WOOX
Innovations is under license. Other trademarks
and trade names are those of their respective
owners.
The N Mark is a trademark or registered
trademark of NFC Forum, Inc. in the United
States and in other countries.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications are subject to change without notice
2014 ©WOOX Innovations Limited.All rights reserved.
Philips and the Philips’ Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used by
WOOX Innovations Limited under license from Koninklijke Philips N.V.
HTL5145B_12_UM_V1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
|