BDL3245E
BDL4245E
BDL4645E
User Manual (English)
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
Regulatory Information
CE Declaration of Conformity
We declare under our responsibility that the product is in conformity with the following standards:
•
•
•
•
•
•
•
•
•
EN60950-1:2006+A11:2009 (Safety requirement of InformationTechnology Equipment)
EN55022:2006+A1:2007 (Radio Disturbance requirement of InformationTechnology Equipment)
EN55024:1998+A1:2001+A2:2003 (Immunity requirement of InformationTechnology Equipment)
EN61000-3-2:2006 (Limits for Harmonic Current Emission)
EN61000-3-3:2008 (Limitation ofVoltage Fluctuation and Flicker) following provisions of directives applicable
2006/95/EC (LowVoltage Directive)
2004/108/EC (EMC Directive)
2005/32/EC (EuP, Energy-using Product Directive) EC No. 642/2009 Implementing
93/68/EEC (Amendment of EMC and LowVoltage Directive) and is produced by a manufacturing organization on ISO9000 level.
Federal Communications Commission (FCC) Notice (U.S. Only)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules.These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions manual, may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Use only RF shielded cable that was supplied with the display when connecting this display to a computer device.
To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.
THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OFTHE CANADIAN INTERFERENCE- CAUSING EQUIPMENT REGULATIONS.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
Polish Center for Testing and Certification Notice
The equipment should draw power from a socket with an attached protection circuit (a three-prong socket).All equipment that works together (computer,
display, printer, and so on) should have the same power supply source.
The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value
no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the
equipment and easily accessible.
A protection mark “B” confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T-42107 and PN-89/
E-06251.
Electric, Magnetic and Electronmagnetic Fields (“EMF”)
1. We manufacture and sell many products targeted at consumers, which, like any electronic apparatus, in general have the ability to emit and receive
electromagnetic signals.
2. One of our leading Business Principles is to take all necessary health and safety measures for our products, to comply with all applicable legal
requirements and to stay well within the EMF standards applicable at the time of producing the products.
3. We are committed to develop, produce and market products that cause no adverse health effects.
4. We confirm that if its products are handled properly for their intended use, they are safe to use according to scientific evidence available today.
5. We play an active role in the development of international EMF and safety standards, enabling us to anticipate further developments in standardization
for early integration in its products.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
Information for U.K. only
WARNING -THIS APPLIANCE MUST BE EARTHED.
(B)
Important:
This apparatus is supplied with an approved moulded 13A plug.To change a fuse in this type of plug
proceed as follows:
(A)
1. Remove fuse cover and fuse.
2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type.
3. Refit the fuse cover.
If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin
plug fitted in its place.
If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse
at the distribution board should not be greater than 5A.
NOTE: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted
into a 13A socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured in accordance with the following code:
BLUE - “NEUTRAL” (“N”)
BROWN - “LIVE” (“L”)
GREEN &YELLOW - “EARTH” (“E”)
1. The GREEN &YELLOW wire must be connected to the terminal in the plug which is marked with
the letter “E” or by the Earth symbol or coloured GREEN or GREEN &YELLOW.
2. The BLUE wire must be connected to the terminal which is marked with the letter “N” or coloured
BLACK.
3. The BROWN wire must be connected to the terminal which marked with the letter “L” or
coloured RED.
Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead
- not simply over the three wires.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
China RoHS
中国电子信息产品污染控制标识要求 (中国RoHS法规标示要求) 产品中有毒有害物质或元素
的名称及含量
有毒有害物质或元素
部件名称
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr 6+)
多溴联苯 多溴二苯醚
(PBDE)
(PBB)
外壳
O
X
X
O
X
O
O
O
O
O
O
O
O
O
O
液晶面板
电路板组件
O
O
O
附件
(遥控器，电源线，连接线)
X
X
O
O
O
O
O
O
O
O
O
O
遥控器电池
O: 表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下.
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求.
10
環保使用期限
此標識指期限(十年)，電子信息產品中含有的有毒有害物質或元素在正常使用的條件下不會發生外泄或突變
，電子信息產品用戶使用該電子信息產品不會對環境造成嚴重污染或對其人身、財產造成嚴重損害的期限。
中国能源效率标识
根据中国大陆《能源效率标识管理办法》，本显示器符合以下要求
能源效率 （cd/W)
能效等级
能效标准
>1.05
1 级
GB 21520-2008
详细有关信息请查阅中国能效标识网： http://www.energylabel.gov.cn/
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
North Europe (Nordic Countries) Information
Placering/Ventilation
VARNING:
FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS.
Placering/Ventilation
ADVARSEL:
SØRGVED PLACERINGEN FOR,AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMTTILGÆNGELIGE.
Paikka/Ilmankierto
VAROITUS:
SIJOITA LAITE SITEN, ETTÄVERKKOJOHTOVOIDAANTARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.
Plassering/Ventilasjon
ADVARSEL:
NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.
End-of-Life Disposal
Your new Public Information Display contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the
amount of reusable materials and to minimize the amount to be disposed of.
Please find out about the local regulations on how to dispose of your old display from your local Philips dealer.
(For customers in Canada and U.S.A.)
This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information on recycling
Waste Electrical and Electronie Equipment-WEEE
Attention users in European Union private households
This marking on the product or on its packaging illustrates that, under European Directive 2002/96/EG governing used electrical
and electronic appliances, this product may not be disposed of with normal household waste.You are responsible for disposal of this
equipment through a designated waste electrical and electronic equipment collection.To determine the locations for dropping off such
waste electrical and electronic, contact your local government office, the waste disposal organization that serves your household or the
store at which you purchased the product.
Attention users in United States:
Like all LCD products, this set contains a lamp with Mercury. Please dispose of according to all Local, State and Federal Laws. For the disposal or recycling
End of Life Directives-Recycling
Your new Public Information Display contains several materials that can be recycled for new users.
Like all LCD produces, this set contains a lamp with Mercury. Please dispose of according to all Local, State, and Federal laws.
As an ENERGY STAR Partner, we have determined that this product meets the ENERGY STAR guidelines for energy efficiency.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
Table Of Contents
1. Unpacking and Installation.....................................1
1.1. Unpacking.....................................................................1
1.2. Package Contents.....................................................1
1.3. Installation Notes......................................................1
3.5.2. Audio connection..................................14
4. OSD Menu..............................................................15
4.1. Navigating the OSD Menu.............................15
4.1.1. Navigating the OSD menu using the
remote control........................................15
1.4. Installing and RemovingTable Stands
(optional).......................................................................2
4.1.2. Navigating the OSD menu using the
display’s control buttons....................15
1.5. Mounting on a Wall.................................................3
1.6. Mounting in Portrait Position.............................4
4.2. OSD Menu Overview........................................15
4.2.1. Picture menu............................................15
4.2.2. Screen menu............................................16
4.2.3. Audio menu..............................................17
4.2.4. PIP menu....................................................17
4.2.5. Configuration1 menu..........................18
4.2.6. Configuration2 menu..........................19
4.2.7. Advanced option menu.....................19
1.6.1. How to use the logo guider for
portrait position........................................4
1.6.2. How to remove the logo.....................4
2. Parts and Functions.................................................5
2.1. Control Panel..............................................................5
2.2. Input/OutputTerminals.........................................6
2.3. Remote Control........................................................7
2.3.1. General functions.....................................7
5. Input Mode..............................................................23
2.3.2. Inserting the batteries in the remote
control.............................................................8
6. Pixel Defect Policy.................................................24
6.1. Pixels and Sub-Pixels............................................24
6.2. Types of Pixel Defects + Dot Definition.24
6.3. Bright Dot Defects...............................................24
6.4. Dark Dot Defects.................................................25
6.5. Proximity of Pixel Defects................................25
6.6. Pixel DefectTolerances......................................25
6.7. MURA..........................................................................25
2.3.3. Handling the remote control.............8
2.3.4. Operating range of the remote
control.............................................................8
3. Connecting External Equipment..........................9
3.1. Using the Switch Cover........................................9
3.2. Connecting External Equipment (DVD/
VCR/VCD)................................................................10
3.2.1. Using COMPONENT video
input..............................................................10
7. Cleaning andTroubleshooting.............................26
7.1. Cleaning......................................................................26
7.2. Troubleshooting......................................................27
3.2.2. Using HDMI video input...................10
3.3. Connecting a PC....................................................11
3.3.1. UsingVGA input.....................................11
3.3.2. Using DVI input......................................11
3.3.3. Using HDMI input.................................12
3.4. External Audio Connection.............................13
3.4.1. Connecting external speakers........13
8. Technical Specifications........................................28
3.4.2. Connecting an external audio
device...........................................................13
3.5. Connecting Multiple Displays in a Daisy-
chain Configuration..............................................14
3.5.1. Video connection..................................14
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
1.
Unpacking and Installation
1.1. Unpacking
•
•
•
•
This product is packed in a carton, together with the standard accessories.
Any other optional accessories will be packed separately.
Due to the size and weight of this display it is recommended for two people to move it.
After opening the carton, ensure that the contents are complete and in good condition.
1.2. Package Contents
Please verify that you received the following items with your package content:
•
•
•
•
•
•
•
•
•
•
LCD display
CD ROM
Remote control with AAA batteries
Power cord (1.8 m)
VGA cable (1.8 m)
POWER
VIDEO
AUDIO
SMART
SOURCE
SOURCE
PIP
ON/OFF
INPUT
CHANGE
CONTRAST
BRIGHTNESS
DISPLAY
MENU
SET
Quick Installation Guide
Power switch cover
AUTO
ADJUST
EXIT
VOL UP
MUTE
VOL DOWN
CD ROM
Screw for Power switch cover (M3x8)
BNC-to-RCA adapter (x5)
Logo guider
Remote Control
and AAA Batteries
* The supplied power cord varies depending on destination.
Power switch cover
Screw for Power switch cover BNC-RCA adapter x 5
(M3 x 8) x 1
For EU
For China
Video Signal Cable
(D-SUB to D-SUB Cable)
Logo guider
For North America
For UK
NOTES:
•
Please make sure that for all other regions, apply a power cord that conforms to the AC voltage of the power socket and has been approved by and
complies with the safety regulations of the particular country.
•
You might like to save the package box and packing material for shipping the display.
1.3. Installation Notes
•
Due to the high power consumption, always use the plug exclusively designed for this product. If an extended line is required, please consult your
service agent.
•
The product should be installed on a flat surface to avoid tipping.The distance between the back of the product and the wall should be maintained
for proper ventilation.Avoid installing the product in the kitchen, bathroom or any other places with high humidity so as not to shorten the service life
of the electronic components.
•
The product can normally operate only under 3000m in altitude. In installations at altitudes above 3000m, some abnormalities may be experienced.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
1.4. Installing and RemovingTable Stands (optional)
To install table stands:
1. Power off the display.
2. Spread a protective sheet on a flat surface.
3. Grab the carrying handles and place the display face-down on the protective sheet.
4. After inserting the stand in the guide block, tighten the screws on both sides of the display.
NOTE: The longer side of the stand should face the front of the display.
Carrying handle
Thumbscrews
Longer portions face the front
Table stand
To remove table stands:
1. Power off the display.
2. Spread a protective sheet on a flat surface.
3. Grab the carrying handles and place the display face-down on the protective sheet.
4. Remove screws using a screwdriver and place them in a safe place for reuse.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
1.5. Mounting on aWall
To mount this display to a wall, you will have to obtain a standard wall-mounting kit (commercially available).We recommend using a mounting interface
that complies withTUV-GS and/or UL1678 standard in North America.
100
200
100
Protective Sheet
200
Table
Tabletop stand
1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath the screen surface so as not to scratch the
screen face.
2. Ensure you have all accessories for mounting this display (wall mount, ceiling mount, table stand, etc).
3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the equipment
or injury to the user or installer. Product warranty does not cover damage caused by improper installation.
4. For the wall-mounting kit, use M6 mounting screws (having a length 10 mm longer than the thickness of the mounting bracket) and tighten them
securely.
Caution:
To prevent the display from falling:
•
For wall or ceiling installation, we recommend installing the display with metal brackets which are commercially available. For detailed installation
instructions, refer to the guide received with the respective bracket.
•
To lessen the probability of injury and damage resulting from fall of the display in case of earthquake or other natural disaster, be sure to consult the
bracket manufacturer for installation location.
Ventilation Requirements for enclosure locating
To allow heat to disperse, leave space between surrounding objects as shown
in the diagram below.
100 mm
100 mm
100 mm
100 mm
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
1.6. Mounting in Portrait Position
This display can be installed in portrait position.
1. Remove the table stand, if attached.
2. Rotate 90 degrees clockwise.The “
” logo should be on the LEFT side when facing the display.
90
90
1.6.1. How to use the logo guider for portrait position
1. Put the guider on the lower-left corner of the front bezel of the display.
Fold down both of its edges.
1
2
3
2. Peel off the protective film at the back of the “
” logo sticker.
” logo
Hold and press the guider with your left hand. Put the “
sticker with its adhesive side down into the logo hole with your right
hand, and press to make it stick tightly onto the front bezel.
3. Remove the guider.
1.6.2. How to remove the logo
1. Prepare a piece of paper with a cutting area of logo as a protector to
prevent the front bezel from scratching.
2
3
1
2. Using a knife, carefully remove the logo sticker with the paper placing
beneath.
3. Tear off the logo sticker.
NOTE: When installing the display on a wall, please consult a professional technician for proper installation.We accept no liability for installations not
performed by a professional technician.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
2.
Parts and Functions
2.1. Control Panel
9
MUTE INPUT
MENU
1
2
3
4
5
6
7
8
NOTE: “Keyboard Control Lock Mode”This function completely
disables the access to all Keyboard Control functions.To
enable or disable the keyboard control lock, press both [
1
POWER button
Use this button to turn the display on or put the display to standby.
]
2
3
and [ ] buttons and hold down continuously for more than
3 (three) seconds.
MUTE button
Switch the audio mute ON/OFF.
9
Remote control sensor and power status indicator
INPUT button
•
Receives command signals from the remote control.
•
Use this button to select the input source.
•
Indicates the operating status of the display:
•
When the On Screen Display menu is active, this is also used as
- Lights green when the display is turned on
the [SET] button.
- Lights red when the display is in standby mode
- Lights amber when the display enters DPMS mode
- When {SCHEDULE} is enabled, the light blinks green and red
4
5
6
7
8
[ ] button
Increase the adjustment while OSD menu is on, or increase the
audio output level while OSD menu is off.
- If the light blinks red, it indicates that a failure has been
detected
[ ] button
Decrease the adjustment while OSD menu is on, or decrease the
audio output level while OSD menu is off.
- Off when the main power of the display is turned off
[
] button
Move the highlight bar up to adjust the selected item while OSD
menu is on.
[
] button
Move the highlight bar down to adjust the selected item while OSD
menu is on.
MENU button
Return to previous menu while OSD menu is on, or to activate the
OSD menu when OSD menu is off.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
2.2. Input/OutputTerminals
BDL3245E
BDL4245E/BDL4645E
BDL4245E/BDL4645E
16
15
15
BDL3245E
(OUT)
(OUT)
Pr Pb
Y
1
3
2
(IN)
(IN)
(IN)
1
2
3
4
5
6
7
8
9
10 11 12 10
13 14
BDL4245E/BDL4645E
(OUT)
(OUT)
Pr Pb
Y
1
3
2
(IN)
(IN)
(IN)
2
1
3
4
5
6
7
8
9
10 11 12 10
13 14
1
2
3
10
11
MAIN POWER SWITCH
Press to switch the main power on/off.
AUDIO IN 1, 2, 3
Connect audio input from external AV device.
•
•
AUDIO IN 1: 3.5mm stereo phone jack
AC IN
AUDIO IN 2, 3: RCA phone jack
Connect the supplied power cord to the wall outlet.
VIDEO IN/OUT
RS232C (OUT/IN)
RS232C network input/output connection for the use of loop-
through function.
•
S-VIDEO IN (Mini DIN 4 pin): Connect the S-VIDEO (Y/C
separate signal) input.
•
•
VIDEO IN (BNC): Connect the composite video signal input.
4
RJ-45
VIDEO OUT (BNC): Connect the composite video signal
output fromVIDEO IN (BNC).
LAN control function for the use of remote control signal from
control center.
12
AUDIO OUT R/L (RCA)
Connect the audio signal output from AUDIO IN 1, 2, or 3 jack to
an external AV device.
5
6
VGA OUT (D-Sub)
Output theVGA signal from theVGA IN (D-Sub).
DVI-D IN
13
14
15
16
SPEAKERS OUT R/L
Connect the audio output to external speakers.
Connect the DVI-D output of a PC, or the HDMI output of an AV
device by using a DVI-HDMI cable.
SPEAKER SWITCH
Press to switch the internal speaker on/off.
7
HDMI IN
Connect the HDMI output of an AV device, or the DVI-D output of
a PC by using a DVI-HDMI cable.
KENSINGTON LOCK
For security and theft prevention.
8
9
VGA IN (D-Sub)
Connect the computerVGA output.
OPS SLOT
Slot for installing the optional OPS module.
COMPONENT IN (BNC)
Connect the componentYPbPr output from external AV device.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
5
6
[DISPLAY] button
Press to turn on/off the information OSD displayed on the upper
right corner of the screen.
2.3. Remote Control
2.3.1. General functions
[ ] button
•
•
•
Press to move the selection left in OSD menu.
Press to decrease the value in OSD menu.
Press to move the sub-picture left in PIP mode.
POWER
1
10
VIDEO
AUDIO
SOURCE
7
8
SMART
SOURCE
[SET] button
Press to activate the setting inside the OSD menu.
2
11
12
[AUTO ADJUST] button
Press to run the Auto Adjust function.
PIP
NOTE: This button is functional forVGA input only.
3
4
ON/OFF
INPUT
CHANGE
9
[MUTE] button
Press to turn the mute function on/off.
13
CONTRAST
BRIGHTNESS
14
15
10
[VIDEO SOURCE] button
5
Press to toggleVideo Source Menu. Press [ ] or [ ] button to
select one of the video sources among HDMI, DVI-D, VGA,
Component, S-Video, or Video . Press [SET] button to confirm
and exit.
DISPLAY
MENU
SET
16
6
7
8
11
12
[AUDIO SOURCE] button
17
18
AUTO
ADJUST
EXIT
Press to toggle Audio Source Menu. Press [ ] or [ ] button
to select one of the audio sources among HDMI, AUDIO1,
AUDIO2, or AUDIO3. Press [SET] button to confirm and exit.
VOL UP
19
20
MUTE
Picture Format button
Press to switch screen aspect ratio.
9
VOL DOWN
•
•
For PC signal: FULL, NORMAL, CUSTOM, and REAL.
ForVideo signal: FULL, NORMAL, DYNAMIC, CUSTOM,
REAL, and 21:9.
NOTE:This button is not functional when the pixel shift function is
active.
13
14
[BRIGHTNESS] button
Press to toggle Brightness Menu. Press [ ] or [ ] button to adjust
the value. Press [MENU] button to confirm and exit.
[
] button
•
Press to move the selection up in OSD menu.
•
Press to move the sub-picture up in PIP mode.
15
16
[MENU] button
Press to turn the OSD menu on/off.
1
[POWER] button
Press to switch on the display from standby mode. Press again to
turn it off and back into standby mode.
[ ] button
•
•
•
Press to move the selection right in OSD menu.
2
[SMART] button
Press to activate Smart Menu. Press [ ] or [ ] button to select
menu options. Press [SET] button to confirm and exit the selection.
Press to increase the value in OSD menu.
Press to move the sub-picture right in PIP mode.
17
18
[EXIT] button
Press to turn back to the previous OSD menu.
•
•
•
Standard: Used for normal images (factory setting)
Highbright: Used for moving image such asVideo
sRGB: Used for text based images
[
] button
•
Press to move the selection down in OSD menu.
3
4
[PIP] (Picture In Picture) button
[ON/OFF]: Turn PIP mode ON/OFF.
•
Press to move the sub-picture down in PIP mode.
[INPUT]: Select the input signal for the sub-picture.
19
20
[VOL UP] button
Press to increase the audio output level.
[CHANGE]: Toggle between the main picture and sub picture.
[VOL DOWN] button
Press to decrease the audio output level.
[CONTRAST] button
Press to activate Contrast Menu. Press [ ] or [ ] button to adjust
the value. Press [MENU] button to confirm and exit.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
2.3.2. Inserting the batteries in the remote control
The remote control is powered by two 1.5V AAA batteries.
To install or replace batteries:
1. Press and then slide the cover to open it.
2. Align the batteries according to the (+) and (–) indications inside the
battery compartment.
3. Replace the cover.
Caution:
The incorrect use of batteries can result in leaks or bursting. Be sure to follow these instructions:
•
•
•
•
Place “AAA” batteries matching the (+) and (–) signs on each battery to the (+) and (–) signs of the battery compartment.
Do not mix battery types.
Do not combine new batteries with used ones. It causes shorter life or leakage of batteries.
Remove the dead batteries immediately to prevent them from liquid leaking in the battery compartment. Don’t touch exposed battery acid, as it can
damage your skin.
NOTE: If you do not intend to use the remote control for a long period, remove the batteries.
2.3.3. Handling the remote control
•
•
•
•
Do not subject to strong shock.
Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry immediately.
Avoid exposure to heat and steam.
Other than to install the batteries, do not open the remote control.
2.3.4. Operating range of the remote control
Point the top of the remote control toward the display’s remote control
sensor when pressing a button.
Use the remote control within a distance of less than 10m/33ft from the
display’s sensor, and a horizontal and vertical angle of less than 30 degrees.
NOTE: The remote control may not function properly when the remote
control sensor on the display is under direct sunlight or strong
illumination, or when there is an obstacle in the path of signal
transmission.
30
30
POWER
SMART
VIDEO
SOURCE
AUDIO
SOURCE
PIP
ON/OFF
INPUT
CHANGE
CONTRAST
BRIGHTNESS
DISPLAY
MENU
SET
AUTO
ADJUST
EXIT
VOL UP
MUTE
VOL DOWN
8
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
3.
Connecting External Equipment
3.1. Using the Switch Cover
A cover for the power switch is provided to prevent the display from being turned on or off accidentally.
To lock the cover into position:
1. Align and insert the cover to the indentation located beside the power switch.
2. Use the screw to lock the cover.
BDL3245E:
BDL4245E / BDL4645E:
1
1
Screw
2
2
Screw
Power switch cover
Power switch cover
9
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
3.2. Connecting External Equipment (DVD/VCR/VCD)
3.2.1. Using COMPONENT video input
COMPONENT
(YPbPr)
Audio Output
DVD / VCR / VCD
COMPONENT
(YPbPr)
To [AUDIO IN 2, 3]
3.2.2. Using HDMI video input
DVD / VCR / VCD
HDMI connector
HDMI connector
10
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
3.3. Connecting a PC
3.3.1. Using VGA input
From analog VGA output
Mini D-Sub 15 pin
From audio output
PC or IBM compatible
To [AUDIO IN 1, 2, 3]
To [VGA IN]
3.3.2. Using DVI input
From DVI output
From audio output
PC or IBM compatible
To [AUDIO IN 1, 2, 3]
To [DVI IN]
11
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
3.3.3. Using HDMI input
From HDMI output
PC or IBM compatible
To [HDMI IN]
12
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
3.4. External Audio Connection
3.4.1. Connecting external speakers
External speaker
3.4.2. Connecting an external audio device
To [AUDIO OUT]
RCA
Audio In
Stereo Amplifier
13
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
3.5. Connecting Multiple Displays in a Daisy-chain Configuration
You can interconnect multiple displays to create a daisy-chain configuration for applications such as a video wall.
NOTE: Maximum 25 displays (5x5) can be used in a daisy-chain configuration.
3.5.1. Video connection
Connect one of the following connections:
•
•
•
Connect the [RS232C OUT] connector of display 1 to the [RS232C IN] connector of display 2.
Connect the [VGA OUT] connector of display 1 to the [VGA IN] connector of display 2.
Connect the [VIDEO OUT] connector of display 1 to the [VIDEO IN] connector of display 2.
To RS-232C IN
To RS-232C OUT
To RS-232C IN
PC
RS-232C Cable
RS-232C Cable
3.5.2. Audio connection
Do one the following connections:
•
•
•
Connect the [AUDIO OUT] connector of display 1 to the [AUDIO IN 2] OR [AUDIO IN 3] connector of display 2.
Connect the [VGA OUT] connector of display 1 to the [VGA IN] connector of display 2.
Connect the [VIDEO OUT] connector of display 1 to the [VIDEO IN] connector of display 2.
To [AUDIO IN 1, 2, 3]
To [AUDIO OUT]
To [AUDIO IN 2, 3]
PC
14
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
4.2. OSD Menu Overview
4.
OSD Menu
An overall view of the On-Screen Display (OSD) structure is shown
below.You can use it as a reference for further adjusting your display.
4.2.1. Picture menu
Brightness
Picture
4.1. Navigating the OSD Menu
Contrast
Screen
Audio
Sharpness
4.1.1. Navigating the OSD menu using the
remote control
Black level
Noise reduction
Tint
PIP
Color
Configuration1
Color temperature
Color control
Smart contrast
Smart picture
MENU
Configuration2
Advanced option
SET
Brightness
EXIT
Adjust the overall image brightness by changing the intensity of the LCD
panel’s backlight.
1. Press [MENU] button on the remote control to display the OSD
Contrast
menu.
Adjust to sharpen the picture quality.The black portions of the picture
become richer in darkness and the white become brighter.
2. Press [ ] or [ ] button to choose the item you want to adjust.
3. Press [SET] or [ ] or button to enter the submenu.
Sharpness
4. In the submenu, press [ ] or [ ] button to toggle among items,
press [ ] or [ ] button to adjust settings. If there is a submenu,
Adjust to improve the image detail.
Black level
press [SET] or [ ] button to enter the submenu.
Adjust to change the image brightness.
5. Press [EXIT] button to return to the previous menu, or press
[MENU] button to exit the OSD menu.
Noise reduction
Adjust to remove the noise in the image.You can select a suitable noise
reduction level.
4.1.2. Navigating the OSD menu using the
display’s control buttons
1. Press [MENU] button to display the OSD menu.
2. Press [ ] or [ ] button to choose the item you want to adjust.
3. Press [SOURCE] or [ ] button to enter the submenu.
The options are: {Off} / {Low} / {Medium} / {High}.
NOTE: This item is functional for HDMI(Video mode), S-Video,Video,
andYPbPr inputs only.
Tint
Adjust to change the color tint of the image.
4. In the submenu, press [ ] or [ ] button to toggle among items,
press [ ] or [ ] button to adjust settings. If there is a submenu,
press [SOURCE] or [ ] button to enter the submenu.
Use the [ ] or [ ] button to adjust. Press the [ ] button and the
flesh tone color turns slightly green. Press the [ ] button and the flesh
tone color turns slightly purple.
5. Press [MENU] button to return to the previous menu, or press
NOTE: This item is functional for HDMI(Video mode), S-Video,Video,
andYPbPr inputs only.
[MENU] button several times to exit the OSD menu.
Color
Adjust to increase or decrease the intensity of colors in the image.
NOTE: This item is functional for S-Video,Video, andYPbPr inputs
only.
Color temperature
Select a color temperature for the image.A lower color temperature
will have a reddish tint, whilst a higher color temperature gives off a
more bluish tint.
The options are: {3000K} / {4000K} / {5000K} / {6500K} / {7500K} /
{9300K} / {10000K} / {Native} / {User}.
Color control
With this function you can adjust the color tones of the image precisely
by changing the R (Red), G (Green) and B (Blue) settings independently.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
NOTE: This item is functional only when {Color temperature} is set
Full
to {User}.
This mode restores the correct proportions
of pictures transmitted in 16:9 using the full
screen display.
Smart contrast
When turned on, this function helps enhance image contrast when
displaying dark scenes.
Normal
The picture is reproduced in 4:3 format and
a black band is displayed on either side of the
picture.
Smart picture
The following smart picture modes are available for:
•
•
PC mode: {Standard} / {Highbright} / {sRGB}.
Dynamic
Video mode: {Standard} / {Highbright} / {Cinema}.
Fill the entire screen by stretching 4:3 pictures
non-proportionally.
Video source
Select a video input source.
Picture reset
Custom
Reset all settings in the Picture menu.
Choose to apply the custom zoom settings in
the Custom Zoom submenu.
4.2.2. Screen menu
Real
This mode displays the image pixel-by-pixel
on screen without scaling the original image
size.
H position
Picture
V position
Screen
Clock
21:9
Clock phase
Audio
The picture is enlarged to 16:9 format.This
mode is recommended when displaying
pictures that have black bands at the top and
bottom (letterbox format).
Zoom mode
PIP
Custom zoom
Screen reset
Configuration1
Configuration2
Custom zoom
You can use this function to further customize the zoom settings to suit
the image you want to display.
Advanced option
NOTE: This item is functional only when the Zoom mode setting is
set to Custom.
H position
Zoom
Press the [ ] button to move the image to the right, or [ ] to move
the image to the left.
Expands the horizontal and vertical sizes of the
image simultaneously.
NOTE: This item is functional forVGA input only.
H zoom
V position
Expands the horizontal size of the image only.
Press the [ ] button to move the image up, or [ ] to move the image
down.
NOTE: This item is functional forVGA input only.
V zoom
Clock
Expands the vertical size of the image only.
Adjust the width of the image.
NOTE: This item is functional forVGA input only.
H position
Clock phase
Moves the horizontal position of the image left
or right.
Adjust to improve the focus, clarity and stability of the image.
NOTE: This item is functional forVGA input only.
Zoom mode
V position
Moves the vertical position of the image up or
down.
The pictures you receive may be transmitted in 16:9 format (wide
screen) or 4:3 format (conventional screen).The 16:9 pictures
sometimes have a black band at the top and bottom of the screen
(letterbox format).
This function allows you to optimize the picture display on screen.The
following zoom modes are available for:
Screen reset
Reset all settings in the Screen menu to factory preset values.
•
•
PC mode: {Full} / {Normal} / {Custom} / {Real}.
Video mode: {Full} / {Normal} / {Dynamic} / {Custom} / {Real} /
{21:9}.
NOTE: If the function for pixel shift andTiling enabled, the menu
items for Zoom mode, H position,V position will be disabled.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
PIP
4.2.3. Audio menu
Select the PIP (Picture-in-Picture) mode.
Balance
Picture
The options are: {Off} / {PIP} / {POP} / {PBP aspect} / {PBP full}.
Treble
PIP input
Screen
Audio
Bass
Select the input signal for the sub-picture.
Volume
Maximum volume
Minimum volume
Mute
PIP change
PIP
Enlarges the smaller picture to become the main picture, and vice versa.
Configuration1
PIP size
Audio source
Audio reset
Card OPS audio
Configuration2
Select the size of the sub picture in the PIP (Picture-in-Picture) mode.
The options are: {Small} / {Medium} / {Large}.
Advanced option
PIP audio
Select the audio source in the PIP (Picture-in-Picture) mode.
•
•
{Main} - Select audio from the main picture
Balance
{Sub} - Select audio from the sub picture.
Adjust to emphasize left or right audio output balance.
PIP reset
Treble
Reset all settings in the PIP menu to factory preset values.
Adjust to increase or decrease higher-pitched sounds.
NOTES:
Bass
•
The PIP function is available only for certain signal source
combinations as shown in the table below.
Adjust to increase or decrease lower-pitched sounds.
•
The availability of the PIP function will also depend on the resolution
of the input signal being used.
Volume
Adjust to increase or decrease the audio output level.
Main Picture
Sub Picture
Card
OPS
DVI
VGA HDMI YPbPr S-Video Video
Maximum volume
Adjust your own limitation for the maximum volume setting.This stops
the volume from being playing at too loud a level.
DVI
VGA
X
X
X
X
O
O
X
X
X
X
X
O
O
X
X
X
X
X
O
O
X
X
X
X
X
O
O
X
O
O
O
O
X
O
O
O
O
X
X
X
X
X
O
O
X
HDMI
Minimum volume
YPbPr
S-Video
Video
Adjust your own limitation for the minimum volume setting.
Mute
X
O
X
O
Card OPS
Turn the mute function on/off.
(O: PIP function available, X: PIP function unavailable)
Audio source
By pressing the [PIP ON/OFF] button on the remote control, you can
change the mode in the order shown below:
Select the audio input source according to the audio signal source
connected to the audio input and HDMI sockets on the display.
PBP aspect
PBP full
PIP
POP
Off
The options are: {HDMI} / {Audio1} / {Audio2} / {Audio3}.
Audio reset
Reset all settings in the Audio menu to factory preset values.
Card OPS audio
The resolutions in the PIP and POP modes are configured as follows:
PIP SIZE {Small} : 320 x 240 pixels
{Medium} : 480 x 320 pixels
{Large} : 640 x 480 pixels
Select the analog or digital audio mode for card OPS.
4.2.4. PIP menu
PIP
POP SIZE: 474 x 355 pixels
Picture
PIP input
NOTE: The images displayed in the sub picture always fit the PIP
sizes shown above irrespective of the aspect ratio of the input
image.
Screen
PIP change
PIP size
Audio
PIP audio
PIP
PIP reset
Configuration1
Configuration2
Advanced option
17
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
•
{Pixel shift} - Select the time interval ({Auto} / {10 ~ 900} Seconds
/ {Off}) for the display to slightly expand the image size and shift the
position of pixels in four directions (up, down, left, or right).
4.2.5. Configuration1 menu
Switch on state
Picture
Auto adjust
NOTE: The default {Auto} setting for menu item Pixel shift does not
support menu items Zoom mode, H/V Position, and PIP.
Screen
Power save
Language
Audio
Color system
Panel saving
Selects the Color System depends on your input video format.
PIP
Color system
The options are: {Auto} / {NTSC} / {PAL} / {SECAM} / {4.43NTSC} /
{PAL-60}.
Network control port
Configuration1
Network settings
NOTE: This item is functional for S-VIDEO orVIDEO input only.
Configuration2
Configuration reset
Network control port
Factory reset
Advanced option
Select the nectwork control port.
The options are: {RS232} / {LAN(RJ45)}.
NOTE: If {LAN(RJ45)} is selected, then {RS232} will not be activated,
even if a cable is attached, and vice versa.
Switch on state
Select the display status used for the next powering on.
Network settings
•
•
•
{Power off} -The display will remain off when the power cord is
connected to a wall outlet.
Assign {IP address}, {Subnet Mask}, and {Default gateway} for the
display.
{Forced on} -The display will turn on when the power cord is
connected to a wall outlet.
Network settings
{Last status} -The display will return to the previous power status
(on/off/standby) when removing and replacing the power cord.
Auto adjust
Network host name
DHCP
9
0
Z
L
Use this function to let the display automatically optimize the display of
VGA input image.
Disable
IP address
172
255
0
-
-
-
16
-
-
-
0
0
0
-
-
-
1
0
0
NOTE: This item is functional forVGA input only.
Subnet mask
255
0
Default gateway
Login user name
Login password
Power save
a
d
m
i
n
Set the display to reduce the power automatically.
0
0
0
0
•
{RGB} - Select {On} to let the display enter DPMS mode when no
signal detected from the HDMI Graphic mode, HDMI, DVI-D, or
VGA inputs after three successive cycles.
[ SET ]
change [SET] in STORE
•
{VIDEO} - Select {On} to let the display enter power saving mode
when no signal detected from the HDMIVideo mode orYPbPr
inputs after three successive cycles.
•
DHCP - Choose to enable or disable the DHCP function. If enabled,
the display will be assigned IP address, Subnet mask and Default
gateway automatically. If disabled, you will be prompted to enter the
following value manually. Finally, press [SET] button to store and save
the chosen values.
Language
Select the language used in the OSD menu.
The options are: {
} / {
} / {
} / {
} / {
} {
/
} /
•
•
•
•
•
IP address
Subnet mask
{
} / {
} / {
}.
Default gateway
Login user name (The default user name is {admin})
Login password (The default password is {0000})
Panel saving
Choose to enable the panel saving functions to reduce the risk of the
“image persistence”.
Configuration reset
•
{Cooling Fan} - Select {On} to turn on the cooling fan all the
time. Select {Auto} to turn on/off the cooling fan according to the
display’s temperature.
Reset all settings in the Configuration1 menu to factory preset values.
Factory reset
NOTES:
Reset all the settings in the OSD menus of {Picture}, {Screen}, {Audio},
{PIP}, {Configuration1}, {Configuration2}, and {Advanced option} to
factory preset values.
•
The default {Auto} option will start running the cooling fan
if the temperature of 65°C (152°F) is reached, and will keep
running for 30 minutes after cooling down to the temperature
of 62°C (144°F).
Press [ ] or [ ] button to select [Reset], and then press [SET] button
to do the reset.
•
A temperature-warning message will be shown on the screen
once the temperature reaches 79°C (174°F).All key function
except [Power] key will then be disabled.
Factory reset
•
{Brightness} - Select {On} and the brightness of the image will be
reduced to an appropriate level, and the Brightness setting in the
Picture menu will become unavailable.
Cancel
Reset
18
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
4.2.6. Configuration2 menu
4.2.7. Advanced option menu
OSD turn off
Picture
Input resolution
Black level expansion
Gamma selection
Scan mode
Picture
Information OSD
Screen
Screen
Audio
Off timer
OSD H-position
Audio
OSD V-position
Scan conversion
Film mode
PIP
PIP
Monitor information
IR control
Configuration1
Configuration2
Advanced option
Configuration1
Keyboard control
Tiling
Configuration2
Heat status
Advanced option
Date and time
OSD turn off
Input resolution
Set the period of time the OSD menu stays on the screen.
The options are: {5 ~ 120} seconds.
Set the resolution of theVGA input.This is only required when the
display is unable to detect theVGA input resolution correctly.
NOTE: This item is functional forVGA input only.
The options are:
Information OSD
Set the period of time the information OSD displayed on the upper
right corner of the screen.The information OSD will display when input
signal is changed.
•
•
•
•
{1024x768 / 1280x768 / 1360x768}
{1400x1050 / 1680x1050}
The information OSD will remain on the screen with {Off} selection.
{1600x1200 / 1920x1200}
The options are: {1 ~ 60} seconds.
{Auto}: Determines the resolution automatically.
OffTimer
The selected settings will become effective after turning off the power
and turn it on again.
Set the display to turn itself off to standby mode within an amount of
time specified.
Black level expansion
The options are: {Off, 1 ~ 24} hours from currrent time.
This feature offers deeper blacks for an even better image quality.
The options are: {Off} / {Low} / {Medium} / {High}.
NOTE: When the “Off timer” is activated, the “Schedule” settings will
be disabled.
NOTE: This item is functional forVideo mode inputs only.
OSD H-position
Gamma selection
Adjust the horizontal position of the OSD menu.
Gamma is what controls the overall brightness of an image. Images
which are not corrected properly can appear too white or too dark, so
controlling the gamma properly can have a huge influence on the overall
picture quality of your display.
OSDV-position
Adjust the vertical position of the OSD menu.
Monitor information
The options are: {Native} / {2.2} / {2.4} / {S gamma}.
Displays the information about your display, including model number,
serial number, operating hours and software version.
Scan mode
Change the display area of the image.
Monitor information
•
{Overscan} - Display about 95% of the original size of the image.
The rest of the areas surrounding the image will be cut off.
Model name:
Serial:
BDL3245E
•
{Underscan} - Display the image in its original size.
Operation Hours:
SW Version:
0 H 3M
NOTE: This item is functional for HDMI-Video timing, DVI-D(HD
timing), DP(HD timing), andYPbPr inputs only.
VER 0.307
Scan conversion
Choose to enable or disable the IP (Interlace to Progressive) conversion
function.
•
{Progressive} - Enable the IP conversion function (recommended).
Once enabled, the interlace input signal will be converted to
progressive format for better display quality.
•
{Interlace} - Disable the IP function.This mode is suitable for
displaying motion pictures, but it increases the chance of image
retention.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
Film mode
Example: 2 x 2 screen matrix (4 displays)
H monitors = 2 displays
Choose to turn on or off the film mode frame conversion function.
V monitors = 2 displays
•
{Auto} - Enable the film mode frame conversion function for
movies and motion pictures.The display converts a 24 frames-per-
second (24 fps) input signal format to DVD video signal format.
Once this function is enabled, it is recommended that you set the
{Scan conversion} function to {Progressive}.
H monitors
Position
•
{Off} - Disable the film mode frame conversion function.This mode
is suitable forTV broadcasting andVCR signals.
1 2
3 4
IR control
Select the operation mode of the remote control when multiple
displays are connected via the RS232C connection.
•
{Normal} - All displays can be operated normally by the remote
control unit.
•
{Primary} - Designate this display as the primary display for remote
control operation. Only this display can be operated by the remote
control.
Example: 5 x 5 screen matrix (25 displays)
H monitors = 5 displays
V monitors = 5 displays
•
•
{Secondary} - Designate this display as the secondary display.This
display can not be operated by the remote control, and will only
receive the control signal from the primary display via the RS232C
connection.
H monitors
Position
1
2
7
3
8
4
9
5
{Lock All} / {Lock all butVolume} / {Lock all but Power} - Lock the
remote control function of this display.To unlock, press and hold the
[DISPLAY] button on the remote control for 5 (five) seconds..
6
10
Keyboard control
11
16
21
12 13
17 18
22 23
14 15
19 20
24 25
Choose to enable or disable the display keyboard (control buttons)
function.
•
•
•
{Lock} - Disable the keyboard function.
{Lock All} / {Lock all butVolume} / {Lock all but Power} - Disable
the keyboard function.
•
•
•
•
H monitors - Select the number of displays on the horizontal side.
V monitors - Select the number of displays on the vertical side.
Position - Select the position of this display in the screen matrix.
Tiling
With this function you can create a single large-screen matrix (video
wall) that consists of up to 25 sets of this display (up to 5-set each at
the vertical and horizontal side).This function requires a daisy-chain
connection.
Frame comp. - Choose to turn the frame compensation function on
or off. If turned on, the display will adjust the image to compensate
for the width of the display bezels in order to accurately display the
image.
Tiling
H monitors
V monitors
Position
1
1
1
Frame comp.
Enable
No
No
Off
Switch on delay
20
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
•
Date and time
Frame comp. - Off
Year
2011
Month
Day
08
04
Hour
20
20
Minute
Daylight saving time
Current date time
2011 . 08 . 04
20 : 20 : 17
Press [SET] to set clock
1. Press [ ] button to enter the submenu.
2. Press [ ] or [ ] button to toggle among the {Year}, {Month},
{Day}, {Hour}, {Minute}, and {Daylight saving time} settings.
Frame comp. - On
3. Press [ ] or [ ] button to adjust all settings except {Daylight
saving time}.
4. Press [SET] button to enter the {Daylight saving} submenu.
5. Press [ ] or [ ] button to select item, press [ ] or [ ] button
to adjust.
Schedule
This function allows you to program up to 7 (seven) different scheduled
time intervals for the display to activate.
You can select:
•
•
•
The time for the display to turn on and turn off.
The days in a week for the display to activate.
Which input source the display will use for each scheduled
activation period.
•
•
Enable: Choose to enable or disable theTiling function. If enabled,
the display will apply the settings in {H monitors}, {V monitors},
{Position}, and {Frame comp.}.
NOTE: You should set up current date and time in {Date and time}
menu before using this function.
1. Press [SET] or [ ] button to enter the submenu.
Switch on delay: Set the power-on delaying time (in seconds).The
default option {Auto} allows a sequential powering-on for each
display by their ID number when multiple displays are connected.
The options are: {Off / Auto / 2, 4, 6, 8, 10, 20, 30, 40, 50}
Schedule
NOTE: TheTiling function will be disabled when the [ON/OFF]
button for PIP is pressed.
Today
2011 . 08 . 04 THU 20 : 19 : 55
1
2
3
4
5
6
7
Heat status
On
:
Off
:
Input
This function allows you to check the thermal status of the display at
any time.
＿
＿
＿
＿
＿
Every day
Wed
MON
TUE
FRI
Date and time
THU
SUN
SAT
Every week
Adjust the current date and time for the display’s internal clock.
2. Press [ ] or [ ] button to select a schedule item (item number 1
~ 7), and then press [ ] button to mark it the item number.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
OPS settings
Schedule
Set the OPS configuration under each power condition..
•
{Auto} - After selecting {Card OPS} for video source input, the
OPS will be set to off when the display power is set to off, or set to
on when the display power is set to on.When set to other video
source inputs, the OPS will always be set to on.
Today
2011 . 08 . 04 THU 20 : 19 : 55
1
2
3
4
5
6
7
1
2
3
On
Off
Input
•
•
{Always off} -The OPS will always be set to off.
＿ : ＿
＿ : ＿
＿
{Always on} -The OPS will always be set to on.
4
Every day
Wed
MON
THU
SUN
TUE
FRI
Advanced option reset
SAT
Every week
Reset all settings in the Advanced option menu to factory preset values.
1. Press [SET] or [ ] button to enter the submenu.
2. Press [ ] or [ ] button to select {Reset} and press the [SET]
button to restore settings to factory preset values.
3. Press [ ] or [ ] button to select the schedule:
3. Press the [EXIT] button or select {Cancel} and press the [SET]
1
button to cancel and then return to the previous menu.
Power-on schedule: Press [ ] or [ ] button to set the hour
and minute for the display to turn on.
2
Picture
Power-off schedule: Press [ ] or [ ] button to set the hour
Schecule
Action
Action
On
and minute for the display to turn off.
Screen
Audio
Monitor ID
Select or leave an empty “__” for both the hour and minute slot if
you do not want to use this power-on or power-off schedule.
DDC/CI
Smart power
Auto signal detection
OPS settings
Off
3
Input-source selection: Press [ ] or [ ] button to select an
input source. If no input source is selected, the input source
will remain the same as last selected.
PIP
Off
Always on
Action
Configuration1
Advanced option reset
4
Date schedule: Press [ ] button to select which day in a
Configuration2
week this schedule item will be take effect, and then press the
[SET] button.
Advanced option
4. For more schedule settings, press [EXIT] button and then repeat
the steps above.A check mark in the box next to the number of
the schedule item indicates that the selected schedule is in effect.
NOTES:
•
•
•
The {Every day} selection in a schedule item takes priority over the
other weekly schedules.
If the schedule overlap, the scheduled power-on time takes priority
over scheduled power-off time.
If there are two schedule items programmed for the same time, the
highest numbered schedule takes priority. For example, if schedule
items #1 and #2 both set the display to power on at 7:00 AM and
off at 5:00 PM, then only schedule item # 1 will take effect.
Monitor ID
Set the ID number for controlling the display via the RS232C
connection. Each display must have a unique ID number when multiple
sets of this display are connected.
DDC/CI
Choose to turn on or off the DDC/CI communication function. Select
{On} for normal use.
Smart power
Set the display to reduce the power consumption automatically.
The options are: {Off} / {Medium} / {High}.
Auto signal detection
Choose to let the display detect and display available signal sources
automatically.
•
{On} - Set the display to display the image automatically once a
signal is connected.
•
{Off} - Once a signal is connected, it can only be selected manually.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
5.
Input Mode
VGA Resolution:
Active Resolution
Standard
Resolution
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
H Pixels
V Lines
480
480
480
400
600
600
768
768
768
800
960
1024
768
768
1200
1080
60 Hz
72 Hz
75 Hz
70 Hz
60 Hz
75 Hz
60 Hz
75 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
25.175 MHz
31.5 MHz
31.5 MHz
33.75 MHz
40 MHz
VGA
640
4:3
Video Graphic Array
WVGA
SVGA
720
800
16:9
4:3
WideVideo Graphic Array
SuperVGA
49.5 MHz
65 MHz
XGA
1024
4:3
Extended Graphic Array
78.75 MHz
79.5 MHz
79.5 MHz
108 MHz
108 MHz
85.5 MHz
85.5 MHz
162 MHz
148.5 MHz
WXGA
WXGA
SXGA
1280
1280
1280
1280
1360
1366
1600
1920
5:3
16:10
4:3
Wide XGA
Wide XGA
Super XGA
Super XGA
Wide XGA
Wide XGA
Ultra XGA
HD1080
SXGA
5:4
WXGA
WXGA
UXGA
HD1080
16:9
16:9
4:3
16:9
SDTV Resolution:
Active Resolution
Standard
Resolution
Refresh Rate
Pixel Rate
Aspect Ratio
Stand for Mode
H Pixels
V Lines
480i
480p
576i
29.97 Hz
59.94 Hz
25 Hz
13.5 MHz
27 MHz
13.5 MHz
27 MHz
720
480
4:3
4:3
Modified NTSC Standard
Modified PAL Standard
720
480
576p
50 Hz
HDTV Resolution:
Active Resolution
Standard
Resolution
Refresh Rate
Pixel Rate
74.25 MHz
74.25 MHz
148.5 MHz
Aspect Ratio
16:9
Stand for Mode
H Pixels
V Lines
50 Hz
60 Hz
25 Hz
30 Hz
50 Hz
60 Hz
720p
1080i
1080p
1280
720
Normally DVB Mode
Normally ATSC Mode
Normally ATSC Mode
1920
1920
1080
1080
16:9
16:9
•
•
•
•
The PC text quality is optimum in HD 1080 mode (1920 x 1080, 60Hz).
Your PC display screen might appear different depending on the manufacture (and your particular version of Windows).
Check your PC instruction book for information about connecting your PC to a monitor.
If a vertical and horizontal frequency-select mode exists, select 60Hz (vertical) and 31.5KHz (horizontal). In some cases, abnormal signals (such as
stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If so, press the [INPUT] button to enter the
video mode.Also, make sure that the PC is connected.
•
•
•
•
When horizontal synchronous signals seem irregular in RGB mode, check PC power saving mode or cable connections.
The display settings table complies to the IBM/VESA standards, and based on the analog input.
The DVI support mode is regarded as same to the PC support mode.
The best timing for the vertical frequency to each mode is 60Hz.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
6.
Pixel Defect Policy
We strive to deliver the highest quality products and use some of the industry’s most advanced manufacturing processes whilst practicing stringent quality
control. However, pixel or sub-pixel defects on the PDP /TFT panels used in Plasma- & LCD- displays are sometimes unavoidable. No manufacturer can
guarantee that all panels will be free from pixel defects, but Philips guarantees that any Plasma- & LCD- displays with an unacceptable number of defects
will be repaired during the warranty period in line with your local guarantee conditions.
This notice explains the different types of pixel defects and defines the acceptable defect level for the BDL4230E LCD screen. In order to qualify for
repair under warranty, the number of pixel defects must exceed a certain level as shown in the reference table. If the LCD screen is within specification a
warranty exchange / claim back will be refused.Additionally, because some types or combinations of pixel defects are more noticeable than others, Philips
sets even higher quality standards for those.
6.1. Pixels and Sub-Pixels
A pixel, or picture element, is composed of three sub-pixels in the primary colors of red, green and
subpixel
blue. Many pixels together form an image.When all sub-pixels of a pixel are lit, the three colored
sub-pixels together appear as a single white pixel.When all are dark, the three colored sub-pixels
together appear as a single black pixel. Other combinations of lit and dark sub-pixels appear as
single pixels of other colors.
pixel
6.2. Types of Pixel Defects + Dot Definition
Pixel and sub-pixel defects appear on the screen in different ways.There are three categories of pixel defects and several types of sub-pixel defects within
each category.
Dot definition =What is a defective “Dot”? :
One or more defective, adjacent sub-pixel are defined as one “dot”.The no. of defective sub-pixels are not relevant to define a defective dot.This means
that a defective dot can consist of one, two or three defective sub-pixels which can be dark or lit.
R G B
One dot = One Pixel; consists of three sub-pixels of Red, Green, and Blue.
6.3. Bright Dot Defects
Bright dot defects appear as pixels or sub-pixels that are always lit or “on”.These are the examples of bright dot defects:
One lit red, green or blue sub pixel
Two adjacent lit sub pixels:
Red + Blue = Purple
Three adjacent lit sub pixels (one white pixel)
Red + Green =Yellow
Green + Blue = Cyan (Light Blue)
24
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
6.4. Dark Dot Defects
Black dot defects appear as pixels or sub-pixels that are always dark or “off”.These are the examples of black dot defects:
One dark dot
Two adjacent dark dots = 1 pair of dark dots
Two dark dots, specifications defines the
minimum distance between dark dots
6.5. Proximity of Pixel Defects
Because pixel and sub-pixels defects of the same type that are nearby one another may be more noticeable, Philips also specifies tolerances for the
proximity of pixel defects. In the table below you can find specifications about:
•
•
•
Allowed amount of adjacent dark dots = (adjacent dark dots =1 pair of dark dots)
Minimum distance between dark dots
Total no. of all defective dots
6.6. Pixel DefectTolerances
In order to qualify for repair due to pixel defects during the warranty period, a PDP /TFT panel in a Philips Plasma / LCD- display must have pixel or sub-
pixel defects exceeding the tolerances listed in the following table.
BRIGHT DOT EFFECT
1 lit sub pixel
ACCEPTABLE LEVEL
2
BLACK DOT EFFECT
1 dark sub pixel
ACCEPTABLE LEVEL
10
12
TOTAL DOT DEFECTS OF ALLTYPES
NOTE: * 1 or 2 adjacent sub pixel defects = 1 dot defect
6.7. MURA
Dark spots or patches may occasionally appear on some liquid crystal display (LCD) panels.This is known within the industry as Mura, which is a Japanese
term for “unevenness.” It is used to describe an irregular pattern or area in which uneven screen uniformity appears under certain conditions. Mura is a
result of the deterioration of the liquid crystal alignment layer and is most commonly caused by long-term operation under high ambient temperatures. It
is an industry- wide phenomenon and Mura is not repairable. It is also not covered by our warranty terms.
Mura has been around since the introduction of LCD technology and with screens getting bigger and in operation 24/7, many displays are running in low
light conditions.This all adds to the possibility of Mura affecting displays.
HOWTO SPOT MURA
There are many symptoms of Mura and also multiple causes. Several of these are listed below:
•
•
•
•
•
•
Impurities or foreign particles in the crystal matrix
Uneven distribution of LCD matrix during manufacturing
Non-uniform luminance distribution of the backlight
Panel assembly induced stress
Flaws within the LCD cells
Thermal induced stress - high temperature operation over long periods of time
HOWTO AVOID MURA
Although we can not guarantee the complete eradication of Mura every time, in general the appearance of Mura can be minimized by these methods:
•
•
•
Lower the backlight brightness
Use a screen saver
Reduce the ambient temperature around the unit
25
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
7.
Cleaning andTroubleshooting
7.1. Cleaning
CautionWhen Using the Display
•
Do not bring your hands, face or objects close to the ventilation holes of the display.The top of the display is usually very hot due to the high
temperature of exhaust air being released through the ventilation holes. Burns or personal injuries may occur if any body parts are brought too
close. Placing any object near the top of the display could also result in heat related damage to the object as well as the display itself.
•
•
Be sure to disconnect all cables before moving the display. Moving the display with its cables attached may damage the cables and thus cause fire
or electric shock.
Disconnect the power plug from the wall outlet as a safety precaution before carrying out any type of cleaning or maintenance procedure.
Front Panel Cleaning Instructions
•
•
The front of the display has been specially treated.Wipe the surface gently using only a cleaning cloth or a soft, lint-free cloth.
If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent solution.Wring the cloth to remove excess liquid.Wipe the surface of
the display to remove dirt.Then use a dry cloth of the same type to dry.
•
•
Do not scratch or hit the surface of the panel with fingers or hard objects of any kind.
Do not use volatile substances such as insert sprays, solvents and thinners.
Cabinet Cleaning Instructions
•
•
If the cabinet becomes dirty, wipe the cabinet with a soft, dry cloth.
If the cabinet is extremely dirty, soak a lint-free cloth in a mild detergent solution.Wring the cloth to remove as much moisture as possible.Wipe
the cabinet. Use another dry cloth to wipe over until the surface is dry.
•
Do not allow any water or detergent to come into contact with the surface of the display. If water or moisture gets inside the unit, operating
problems, electrical and shock hazards may result.
•
•
•
Do not scratch or hit the cabinet with fingers or hard objects of any kind.
Do not use volatile substances such as insert sprays, solvents and thinners on the cabinet.
Do not place anything made from rubber or PVC near the cabinet for any extended periods of time.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
7.2. Troubleshooting
Symptom
Possible Cause
Remedy
No picture is displayed
1. The power cord is disconnected.
1. Plug in the power cord.
2. The main power switch on the back of the
display is not switched on.
2. Make sure the power switch is switched on.
3. Connect a signal connection to the display.
3. The selected input has no connection.
4. The display is in standby mode.
Interference displayed on the display or audible Caused by surrounding electrical appliances or
Move the display to another location to see is the
interference is reduced.
noise is heard
fluorescent lights.
Color is abnormal
The signal cable is not connected properly.
Make sure that the signal cable is attached firmly
to the back of the display.
Picture is distorted with abnormal patterns
1. The signal cable is not connected properly.
1. Make sure that the signal cable is attached
firmly.
2. The input signal is beyond the capabilities of
the display.
2. Check the video signal source to see if it
is beyond the range of the display. Please
verify its specifications with this display’s
specification section.
Display image doesn’t fill up the full size of the The zoom mode is not correctly set.
screen
Use the Zoom mode or Custom zoom function
in the Screen menu to fine tune display geometry
and time frequency parameter.
Can hear sound, but no picture
Improperly connected source signal cable.
Make sure that both video inputs and sound
inputs are correctly connected.
Can see picture but no sound is heard
1. Improperly connected source signal cable.
2. Volume is turned all the way down.
3. [MUTE] is turned on.
1. Make sure that both video inputs and sound
inputs are correctly connected.
2. Press [VOL UP] or [VOL DOWN] button to
hear sound.
4. No external speaker connected.
3. Switch MUTE off by using the [MUTE]
button.
4. Connect external speakers and adjust the
volume to a suitable level.
Some picture elements do not light up
Some pixels of the display may not turn on.
This display is manufactured using an extremely
high level of precision technology: however,
sometimes some pixels of the display may not
display.This is not a malfunction.
After-Images can still be seen on the display
after the display is powered off. (Examples
of still pictures include logos, video games,
computer images, and images displayed in 4:3
normal mode)
A still picture is displayed for an over extended
period of time
Do not allow a still image to be displayed for
an extended period of time as this can cause a
permanent after-image to remain on the display.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
8.
Technical Specifications
BDL3245E
Display:
Item
Specifications
32” LCD
Screen Size (Active Area)
Aspect ratio
16:9
Number of pixels
Pixel pitch
1920 (H) x 1080 (V)
0.36375 (H) x 0.36375 (V) [mm]
1.06B colors
500 cd/m2
Displayable colors
Brightness (typical)
Contrast ratio (typical)
Viewing angle
1450:1
178 degrees
In/OutTerminals:
Item
Specifications
Speaker Output
Internal Speaker
10W (L) + 10W (R) [RMS]/8Ω
1 Way 1 Speaker System
82 dB/W/M/160 Hz ~ 13 KHz
Audio Output
Audio Input
RCA Jack x 1
0.5V [rms] (Normal)/ 2 Channel (L+R)
0.5V [rms] (Normal)/ 2 Channel (L+R)
RCA Jack x 2
3.5 mm Stereo x 1
RS232C
RJ-45
D-Sub Jack x 2
(9 pin)
TXD + RXD (1:1)
10/100 LAN Port
RJ-45 Jack x 1
(8 pin)
HDMI Input
HDMI Jack x 1
Digital RGB:TMDS (Video + Audio)
(Type A) (18 pin)
MAX:Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel (L+R)
Supports LPCM only
DVI-D Input
VGA Input
DVI-D jack
Digital RGB:TMDS (Video)
D-Sub Jack x 1
(15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V:TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
VGA Output
Component Input
Video Input
D-Sub Jack x 1
(15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V:TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
BNC Jack x 3
Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω)
MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
S-VIDEO Jack x 1
BNC Jack x 1
Y: 1V [p-p] (75Ω), C: 0.3V [p-p] (75Ω)
Composite 1V [p-p] (75Ω)
Video Output
BNC Jack x 1
Composite 1V [p-p] (75Ω)
General:
Item
Specifications
Power Supply
Power Consumption (Max)
AC 100 ~ 240V, 50 ~ 60Hz
160W
Power Consumption (Standby & Off)
Dimensions (With Stand) [W x H x D]
Dimensions (Without Stand) [W x H x D]
Weight (With Stand)
<0.5W (RS232 in active)
773.6 x 505.1 x 239.8 mm
773.6 x 468.3 x 116 mm
14 Kg
Weight (Without Stand)
12.8 Kg
Gross Weight
17 Kg
28
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
Environmental Condition:
Item
Specifications
Temperature
Humidity
Altitude
Operational
0 ~ 40°C
Storage
-20 ~ 60°C
Operational
Storage
20 ~ 80% RH (No condensation)
5 ~ 95% RH (No condensation)
0 ~ 3,000 m
Operational
Storage / Shipment
0 ~ 9,000 m
Internal Speaker:
Item
Specifications
1 Way 1 Speaker
10 W (RMS)
8Ω
Type
Input
Impedance
Output Sound Pressure
Frequency Response
82 dB/W/M
160 Hz ~ 13 KHz
29
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
BDL4245E
Display:
Item
Specifications
42” LCD
Screen Size (Active Area)
Aspect ratio
16:9
Number of pixels
Pixel pitch
1920 (H) x 1080 (V)
0.4845 (H) x 0.4845 (V) [mm]
16.7M colors
450 cd/m2
Displayable colors
Brightness (typical)
Contrast ratio (typical)
Viewing angle
4000:1
178 degrees
In/OutTerminals:
Item
Specifications
Speaker Output
Internal Speaker
10W (L) + 10W (R) [RMS]/8Ω
1 Way 1 Speaker System
82 dB/W/M/160 Hz ~ 13 KHz
Audio Output
Audio Input
RCA Jack x 1
0.5V [rms] (Normal)/ 2 Channel (L+R)
0.5V [rms] (Normal)/ 2 Channel (L+R)
RCA Jack x 2
3.5 mm Stereo x 1
RS232C
RJ-45
D-Sub Jack x 2
(9 pin)
TXD + RXD (1:1)
10/100 LAN Port
RJ-45 Jack x 1
(8 pin)
HDMI Input
HDMI Jack x 1
Digital RGB:TMDS (Video + Audio)
(Type A) (18 pin)
MAX:Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel (L+R)
Supports LPCM only
DVI-D Input
VGA Input
DVI-D jack
Digital RGB:TMDS (Video)
D-Sub Jack x 1
(15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V:TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
VGA Output
Component Input
Video Input
D-Sub Jack x 1
(15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V:TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
BNC Jack x 3
Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω)
MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
S-VIDEO Jack x 1
BNC Jack x 1
Y: 1V [p-p] (75Ω), C: 0.3V [p-p] (75Ω)
Composite 1V [p-p] (75Ω)
Video Output
BNC Jack x 1
Composite 1V [p-p] (75Ω)
General:
Item
Specifications
Power Supply
Power Consumption (Max)
AC 100 ~ 240V, 50 ~ 60Hz
260W
Power Consumption (Standby & Off)
Dimensions (With Stand) [W x H x D]
Dimensions (Without Stand) [W x H x D]
Weight (With Stand)
<0.5W (RS232 in active)
991.6 x 621 x 329.6 mm
991.6 x 584 x 115.5 mm
23.6 Kg
Weight (Without Stand)
22 Kg
Gross Weight
27.5 Kg
30
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
Environmental Condition:
Item
Specifications
Temperature
Humidity
Altitude
Operational
0 ~ 40°C
Storage
-20 ~ 60°C
Operational
Storage
20 ~ 80% RH (No condensation)
5 ~ 95% RH (No condensation)
0 ~ 3,000 m
Operational
Internal Speaker:
Item
Specifications
1 Way 1 Speaker
10 W (RMS)
8Ω
Type
Input
Impedance
Output Sound Pressure
Frequency Response
82 dB/W/M
160 Hz ~ 13 KHz
31
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
BDL4645E
Display:
Item
Specifications
46” LCD
Screen Size (Active Area)
Aspect ratio
16:9
Number of pixels
Pixel pitch
1920 (H) x 1080 (V)
0.5302 (H) x 0.53025 (V) [mm]
16.7M colors
400 cd/m2
Displayable colors
Brightness (typical)
Contrast ratio (typical)
Viewing angle
4000:1
178 degrees
In/OutTerminals:
Item
Specifications
Speaker Output
Internal Speaker
10W (L) + 10W (R) [RMS]/8Ω
1 Way 1 Speaker System
82 dB/W/M/160 Hz ~ 13 KHz
Audio Output
Audio Input
RCA Jack x 1
0.5V [rms] (Normal)/ 2 Channel (L+R)
0.5V [rms] (Normal)/ 2 Channel (L+R)
RCA Jack x 2
3.5 mm Stereo x 1
RS232C
RJ-45
D-Sub Jack x 2
(9 pin)
TXD + RXD (1:1)
10/100 LAN Port
RJ-45 Jack x 1
(8 pin)
HDMI Input
HDMI Jack x 1
Digital RGB:TMDS (Video + Audio)
(Type A) (18 pin)
MAX:Video - 720p, 1080p, 1920 x 1080/60 Hz (WUXGA) Audio - 48 KHz/ 2 Channel (L+R)
Supports LPCM only
DVI-D Input
VGA Input
DVI-D jack
Digital RGB:TMDS (Video)
D-Sub Jack x 1
(15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V:TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
VGA Output
Component Input
Video Input
D-Sub Jack x 1
(15 pin)
Analog RGB: 0.7V [p-p] (75Ω), H/CS/V:TTL (2.2kΩ), SOG: 1V [p-p] (75Ω)
MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)
BNC Jack x 3
Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr: 0.7V [p-p] (75Ω)
MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p
S-VIDEO Jack x 1
BNC Jack x 1
Y: 1V [p-p] (75Ω), C: 0.3V [p-p] (75Ω)
Composite 1V [p-p] (75Ω)
Video Output
BNC Jack x 1
Composite 1V [p-p] (75Ω)
General:
Item
Specifications
Power Supply
Power Consumption (Max)
AC 100 ~ 240V, 50 ~ 60Hz
270W
Power Consumption (Standby & Off)
Dimensions (With Stand) [W x H x D]
Dimensions (Without Stand) [W x H x D]
Weight (With Stand)
<0.5W (RS232 in active)
1091.1 x 681.7 x 329.6 mm
1091.1 x 645.7 x 120.1 mm
26.3 Kg
Weight (Without Stand)
24.6 Kg
Gross Weight
31 Kg
32
Download from Www.Somanuals.com. All Manuals Search And Download.
BDL3245E / BDL4245E / BDL4645E
Environmental Condition:
Item
Specifications
Temperature
Humidity
Altitude
Operational
0 ~ 40°C
Storage
-20 ~ 60°C
Operational
Storage
20 ~ 80% RH (No condensation)
5 ~ 95% RH (No condensation)
0 ~ 3,000 m
Operational
Internal Speaker:
Item
Specifications
1 Way 1 Speaker
10 W (RMS)
8Ω
Type
Input
Impedance
Output Sound Pressure
Frequency Response
82 dB/W/M
160 Hz ~ 13 KHz
33
Download from Www.Somanuals.com. All Manuals Search And Download.
2011 © Koninklijke Philips Electronics N.V. All rights reserved.
Philips and the Philips Shield Emblem are registered trademarks of
Koninklijke Philips Electronics N.V. and are used under license from
Koninklijke Philips Electronics N.V.
Specifications are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|