Perlick Refrigerator CS1DPSP User Manual

INSTALLATION AND OPERATION INSTRUCTIONS  
SINGLE DOOR BACK BAR COOLER  
MODEL NOS.  
CS1DPSP  
Table of Contents  
IMPORTANT INFORMATION  
PREPARING THE CABINET FOR USE  
A Warranty card is enclosed that must be filled out  
and mailed to the Perlick Corporation in order to reg-  
ister the warranty. If the card is not returned to  
Perlick, the warranty period will begin from the date  
the equipment is shipped from the factory.  
Specifications.........................................................2  
List of Included Parts.............................................3  
Tools Required.......................................................3  
Plumbing................................................................3  
Electrical ................................................................3  
Uncrating ...............................................................3  
Installing Casters...................................................3  
Placing the Cabinet ...............................................3  
Leveling the Cabinet..............................................3  
Installing Base Plates ............................................3  
TEMPERATURE  
Refrigeration and Temperature Control.................4  
Adjusting the Temperature.....................................4  
CLEANING  
Cleaning the Cabinet.............................................4  
Cleaning the Condenser........................................4  
Condenser .............................................................4  
GENERAL INFORMATION  
This manual has been prepared to assist you in the  
installation of your Single Keg Dispenser and to  
acquaint you with its operation and maintenance.  
We dedicate considerable time to ensure that our  
products provide the highest level of customer  
satisfaction. If service is required, your dealer can  
provide you with a list of qualified service agents. For  
your own protection, never return merchandise for  
credit without our approval.  
We thank you for selecting a Perlick product and  
assure you of our continuing interest in your  
satisfaction.  
REPLACEMENT PARTS.......................................5  
Wiring Diagram......................................................6  
WARNING: When lifting, the full weight of the  
cabinet must be supported. Lift from the cabinet  
base and not from the top. Improper lifting can  
result in severe damage to the cabinet.  
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069  
Toll Free 800-558-5592 • E-Mail: [email protected] • www.Perlick.com  
Form No. Z2091A  
Rev. 08.03.04  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Preparing the Cabinet for Use – Single Door Back Bar Cooler  
Parts List  
Installing Casters (Optional)  
(2) Shelves.  
Mini-Flourescent Light.  
Shelf Clips.  
Attach four casters to the cabinet bottom; rigid cast-  
ers at the rear and swivel casters on the front. Use  
the supplied 1/4”- 20 x 3/4” hex head self-tapping  
machine screws.  
Tools Required  
#2 Phillips Screwdriver.  
10” Crescent Wrench.  
Placing the Cabinet  
9/16” Allen Wrench.  
3/8” Nut driver.  
power Drill or Driver (for Leg Installation).  
Push the cabinet into place using rollers when  
necessary. Important: Proper air flow around the  
condensing unit is necessary for efficient operation.  
Never obstruct the air flow in and out of the  
condensing unit. A minimum of 2” clearance is  
required from back.  
Plumbing  
Features a floor drain with a 34” female pipe thread  
connection for disposal of condensate. Remove  
bottom or side drain plug with Allen wrench and  
attach 34” male pipe to external drain.  
Leveling the Cabinet  
When the cabinet is in place, check installation with  
carpenter’s level. When perfectly level, accumulated  
water will drain out. A slight pitch to the drain side  
will not harm the cabinet. Water may accumulate if  
cabinet is pitched to the opposite side.  
Electrical  
The cabinet must be connected to a separately  
fused power source (see electrical specification  
plate) and grounded in accordance with National  
and Local Electrical Codes. Caution: Do not  
attempt to operate the equipment on any other  
power source than that listed on the Electrical  
Specification plate.  
Installing Base Plate (Optional)  
Attach brackets to cabinet bottom in holes provided.  
Use #10 self-drilling hex sheetmetal screws. (See  
separate instructions, provided with kit). When  
returning cabinet to upright position, be careful not  
to bend brackets.  
Uncrating and Inspection  
Remove all crating material before operating.  
Carefully inspect cabinet for hidden damage. If  
damage is discovered, file your claim immediately  
with the transportation company. Perlick is  
not responsible for damage in transit.  
WARNING!  
To avoid compressor damage,after returning  
cabinet to an upright position, let unit stand for  
24 hours before plugging it in and running the unit.  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2091A  
Rev. 08.03.04  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
General Information – Single Door Back Bar Cooler  
Refrigeration and Temperature Control  
Cleaning the Cabinet  
Use a mild detergent and water to clean the inside  
and outside of the cabinet. Dry thoroughly. Never  
use a scouring pad or abrasive cleanser.  
NOTE: An industrial strength, commercial cleaner  
can be used to clean the outside of painted  
cabinets.  
The Back Bar cabinet is equipped with a heavy-  
duty refrigeration system designed to automatically  
maintain a storage temperature of 36-41 degrees F.  
The control is factory set at 38 degrees F.  
Cleaning the Condenser  
Use a long handled, stiff brush to clean the dirt from  
the front surface of the condenser. Keeping the  
condenser free from dust and dirt will ensure effi-  
cient operation.  
CAUTION: Do not bend the fins while brushing the  
front of the condenser.  
Condenser  
The condenser (located behind the back cover)  
should be inspected every 30 days and cleaned, if  
necessary. Failure to keep the condenser clean will  
cause a loss in condenser unit efficiency.  
Adjusting the temperature  
The temperature control is inside the cabinet on  
the right-hand side of the evaporator fan panel  
assembly. You will need a screwdriver to turn the  
adjusting screw. Make small adjustments until the  
desired temperature is achieved.  
Colder Temperatures:  
Turn the adjusting screw clockwise (to the right).  
Warmer Temperatures:  
Turn the adjusting screw counterclockwise  
(to the left).  
In normal operation the condensing unit will run  
approximately 16 hours per day. The condenser fan  
motor turns off and on with the condensing unit.  
The evaporator fan motor runs continuously. The  
fan motors are lifetime lubricated and will require  
no oiling.  
NOTE:  
Cabinet Temperatures lower than 34° will not allow  
for proper defrosting of the evaporator coil. If  
defrosting is necessary, turn the control knob to the  
OFF position until coil is defrosted.  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2091A  
Rev. 08.03.04  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Replacement Parts Single Door Back Bar Cooler  
MODEL NOS.  
CS1DP  
Item Description  
Part #’s  
1
2
3
4
5
6
7
8
9
10  
11  
12  
13  
14  
15  
16  
Compressor for R134a  
C22650  
C15240A  
61289-1  
C6914  
62209-1  
62433-1  
62131-1  
C18634A  
62132-1  
C25400A1  
C14649  
C15239A  
62212B  
62439  
57360  
64357SRBL  
64357SLBL  
63407R  
63407L  
Condenser fan motor  
Condenser fan motor bracket  
Condenser fan blade  
Condenser fan pan  
Rear panel  
Back panel partition  
Condenser assembly  
Condenser panel  
Evaporator fan guard  
Evaporator fan blade - 512”  
Evaporator fan motor  
Evaporator assembly - complete  
Top assembly  
Temperature control parts kit  
Right hinged door assembly  
Left hinged door assembly  
Door hinge kit, right  
Door hinge kit, left  
17  
18  
19  
20  
Magnetic door gasket  
Door sill  
Door handle  
62085-1  
60944-1  
C31409-1  
Parts Not Shown on Drawing  
Light, mini-flourecent  
Wiring harness  
57822A  
61346-1  
57851  
Door lock with keys  
Drain line hose kit  
57854  
14  
12  
13  
11  
9
10  
15  
6
7
16  
8
5
4
3
2
17  
1
20  
19  
18  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.  
Form No. Z2091A  
Rev. 08.03.04  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wiring Diagram – Single Door Back Bar Cooler  
EVAPORATOR FAN  
BLACK  
OUTLET  
WHITE  
THERMOSTAT  
BLACK  
CONDENSING UNIT  
BLACK  
WHITE  
GREEN  
POWER CONNECTION  
JUNCTION BLOCK  
8300 West Good Hope Road • Milwaukee, WI 53223 • Phone 414-353-7060 • Fax 414-353-7069  
Toll Free 800-558-5592 • E-Mail: [email protected] • www.Perlick.com  
Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice. Form No. Z2091A  
Rev. 08.03.04  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pelco Musical Toy Instrument C529M D User Manual
Pelco Security Camera C2423M User Manual
Perle Systems Cable Box S 4GPT DSFP User Manual
Philips DVD Recorder DVDR3575H User Manual
Philips Electric Shaver 6891XLD User Manual
Philips TV DVD Combo CDV19BPH User Manual
Philips TV Mount SQM6325 User Manual
Pioneer Car Video System AVH P5150DVD User Manual
Pioneer Speaker PDP S13 LR User Manual
Polaroid Flat Panel Television 1911 TLXB User Manual