I N S T A L L A T I O N / O P E R A T I O N
VS5104/VS5108
Sequential Switcher
®
C831M-F (10/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
Description
The VS5104 and VS5108 are sequential switchers designed to switch four cameras (VS5104) or eight cameras (VS5108) to one monitor.
MODELS
VS5104
Desktop, 4-position, single output sequential switcher without alarm inputs
Same as VS5104 except 230 VAC operation
VS5104/220
VS5108
Desktop, 8-position, single output sequential switcher without alarm inputs
Same as VS5108 except 230 VAC operation
VS5108/220
C831M-F (10/04)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
The VS5104/VS5108 switcher is designed for either looping or terminating operation. The unit is shipped ready for terminating operation, but it
can be modified for looping operation. Looping and terminating inputs may be mixed.
1. To install the VS5104/VS5108, do the following:
a. Terminating Operation - Proceed to step 2.
b. Looping Operation - To convert to looping operation, remove the cover. Locate the 75-ohm resistors at the rear of the BNC jacks. Use wire
cutters to clip one of the resistor leads for each input that you want to loop. Refer to Figure 1. Replace the cover.
75-OHM RESISTOR
CLIP
HERE
BNC CONNECTOR
Figure 1. Rear Panel Internal View
3. Connect the AC adapter to the 12 VAC input socket on the switcher. Connect the transformer to a 120 or 230 VAC power supply.
4. Set all channel switches to the AUTO (center). If a video input is not connected, set the corresponding channel switch to the BYP ASS (down)
position.
5. Adjust the DWELL interval control with a screwdriver to the desired switching interval, 1 to 70 seconds nominal. Rotate the control clockwise for
longer intervals and counter-clockwise for shorter intervals. This control is a 15-turn precision potentiometer. The approximate ratio is one full turn
per 4–5 seconds of delay.
VS5104
VS5108
MONITOR
AUTO
MONITOR
AUTO
BYPASS
BYPASS
DWELL
DWELL
1
2
3
4
1
2
3
4
5
6
7
8
VS5104 VIDEO SWITCHER
VS5108 VIDEO SWITCHER
FRONT VIEW
FRONT VIEW
12 VAC
INPUT
12 VAC
INPUT
MON
OUT
MON
OUT
BACK VIEW
BACK VIEW
Figure 2. VS5104/VS5108 System Configuration
4
C831M-F (10/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Automatic Sequence Viewing - To automatically sequence all the cameras through the monitor, set all channel switches to the AUTO (center)
position.
Bypass Operation - To bypass a camera in the automatic sequence, set the camera’s channel switch to the BYPASS (down) position.
Single Camera Viewing - To continuously view from a single camera, set the channel switch for the camera to the MONITOR (up) position.
MAINTENANCE
Under normal operating conditions and usage, maintenance of this equipment is not necessary. The VS5104/VS5108 has no operator serviceable
components and should be serviced by a trained technician or returned to the factory for repair.
C831M-F (10/04)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
VIDEO
Inputs
Terminating (75 ohms) or looping
75 ohms
Output
Gain
Unity
Dwell
Adjustable from 1-70 seconds nominal
Flat within 1 dB to 10 MHz
Frequency Response
Maximum
Signal Level
2 Vp-p
Tilt
Less than 2%
Crosstalk
Better than -40 dB at 5.5 MHz
ELECTRICAL
Input Voltage
120 VAC, 50/60 Hz or 230 VAC, 50 Hz to dedicated wall transformer
Power Requirements
for Transformer
1.5 VA (.125 amp) at 12 volts RMS 15%, 50/60 Hz from a dedicated isolated power source. (Wall transformer provided
with unit.) These units are also capable of operating on 12 VDC for use in mobile applications.
GENERAL
Construction
Chassis
Cover
Steel, zinc plated
Steel, black polyester powder coat
Aluminum, black polyester powder coat, white silkscreen
Panel
Environment
32° to 120°F (0° to 49°C)
Dimensions
VS5104
VS5108
1.77 (H) x 5.51 (W) x 8.81 (D) inches (4.50 x 14.00 x 22.38 cm)
1.77 (H) x 8.61 (W) x 9.25 (D) inches (4.50 x 21.87 x 23.50 cm)
Weight
VS5104
VS5108
2.53 lb (1.15 kg)
3.82 lb (1.73 kg)
Ratings
Meets NEMA Type 1 standards
(Design and product specifications subject to change without notice.)
6
C831M-F (10/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
1. Model and serial number
Exceptions to this warranty are as noted below:
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
•
Five years on FT/FR8000 Series fiber optic products and the following fixed camera models:
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and CC3651H-2X.
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.
•
Three years on all other fixed camera models (including Camclosure® Integrated Camera
Systems) and Genex® Series (multiplexers, server, and keyboard).
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
•
•
Two years on all standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM8500/CM9500/CM9700 Series Matrix, DF5
and DF8 Series Fixed Dome products.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).
•
Two years on Spectra®, Esprit®, and PS20 Scanners, including when used in continuous
motion applications.
•
•
Two years on Esprit® and WW5700 series window wiper (excluding wiper blades).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Eighteen months on DX Series digital video recorders and NVR300 series network video
recorders.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
Phone: 650-737-1700
Fax: 650-737-0933
REVISION HISTORY
Manual #
C831M-E
C831M-F
Date
11/99
10/04
Comments
Updated manual to new format. Combined C831M-D (VS5104) and C832M-D (VS5108) into one manual.
Updated manual to new format. Revised Important Safety Instructions.
Pelco, the Pelco logo, Spectra, Genex, Esprit, Camclosure, and Legacy are registered trademarks of Pelco.
© Copyright 2004, Pelco. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
ISO9001
United States Canada United Kingdom The Netherlands Singapore Spain Scandinavia France Middle East
|
|
|
|
|
|
|
|
Download from Www.Somanuals.com. All Manuals Search And Download.
|