INSTALLATION/OPERATION
PelcoNet™ Multimedia
Transmission Via Networks
®
NET104A Series
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Section
Page
IMPORTANT SAFEGUARDS AND WARNINGS ..................................................................................... 8
UNPACKING INSTRUCTIONS .................................................................................................... 8
INSTRUCTIONS FOR THE NETWORK ADMINISTRATOR ..................................................................... 9
THE TRANSMITTER ................................................................................................................... 9
THE BROWSER ......................................................................................................................... 10
MINIMUM REQUIREMENTS .................................................................................................... 10
WHAT IS THE PELCONET NET104A TRANSMISSION SYSTEM? ....................................................... 11
HOW DO LANS AND WANS WORK?....................................................................................... 11
WHO SHOULD INSTALL THE PELCONET NET104A TRANSMISSION SYSTEM? .................... 11
OVERVIEW ......................................................................................................................................... 12
DESCRIPTION ........................................................................................................................... 12
SOFTWARE VERSION ............................................................................................................... 13
PACKAGE CONTENTS .............................................................................................................. 13
MODELS ................................................................................................................................... 13
FRONT PANEL LEDS ................................................................................................................. 14
REAR PANEL CONNECTORS .................................................................................................... 15
QUICK INSTALLATION GUIDE ............................................................................................................ 16
STEP 1: CONNECTING A CAMERA OR MONITOR ................................................................... 16
STEP 2: CONNECTING ADDITIONAL ITEMS ............................................................................ 17
STEP 3: CONNECTING TO THE LAN PORT ............................................................................... 17
STEP 4: CONNECTING POWER ................................................................................................ 18
STEP 5: SELECTING AN IP ADDRESS FOR YOUR NETWORK .................................................. 19
STEP 6: USING A PC’S WEB BROWSER TO CONFIGURE THE NETWORK .............................. 19
STEP 7: WHAT IS NEXT? .......................................................................................................... 19
TYPICAL APPLICATIONS ................................................................................................................... 20
DISPLAYING REMOTE VIDEO ON A WEB BROWSER .............................................................. 20
DISPLAYING VIDEO VIA A TRANSMITTER-TO-RECEIVER CONNECTION ................................ 22
DIAGRAMS OF TYPICAL APPLICATIONS .................................................................................. 24
HARDWARE INSTALLATION ............................................................................................................... 30
CONNECTING VIDEO SOURCES OR DISPLAYS ........................................................................ 30
CONNECTING AUDIO EQUIPMENT .......................................................................................... 30
CONNECTING DATA TERMINALS ............................................................................................ 31
USE AS CONTROL TERMINAL PORT ............................................................................... 31
USE AS TRANSPARENT DATA PORT ............................................................................... 32
CONNECTING EXTERNAL SENSORS ....................................................................................... 33
CONTROLLING PERIPHERAL DEVICES ..................................................................................... 34
CONNECTING TO A LAN .......................................................................................................... 34
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
3
CONFIGURATION ............................................................................................................................... 34
CONFIGURATION USING A TERMINAL PROGRAM ................................................................. 34
TYPICAL SESSION ........................................................................................................... 35
COMMAND REFERENCE ................................................................................................. 36
CONFIGURATION USING A WEB BROWSER ........................................................................... 38
WEB SERVER CONCEPT .................................................................................................. 38
NET-MANAGER ............................................................................................................... 38
QUICK GUIDE TO THE MENU STRUCTURE ..................................................................... 39
PELCONET NET104A HOME PAGE .................................................................................. 40
GENERAL CONFIGURATION PAGE .................................................................................. 42
NETWORK SETTINGS CONFIGURATION PAGE ............................................................... 46
VIDEO SETTINGS CONFIGURATION PAGE ...................................................................... 48
AUDIO SETTINGS CONFIGURATION PAGE ..................................................................... 52
ALARM SETTINGS CONFIGURATION PAGE .................................................................... 54
INTERFACE SETTINGS CONFIGURATION PAGE .............................................................. 60
LIVE VIDEO AND SERVER PUSH VIDEO PAGES ................................................................................ 62
WEB BROWSER CONTROL PAGES .................................................................................................... 63
ACCESSING THESE PAGES ...................................................................................................... 63
CONTROLLING THE DISPLAY ................................................................................................... 64
MATRIX CONTROL LIVE VIDEO/SERVER PUSH PAGE CONTENTS .......................................... 65
GENEX LIVE VIDEO/SERVER PUSH PAGE CONTENTS ............................................................. 66
SPECTRA LIVE VIDEO/SERVER PUSH PAGE CONTENTS ......................................................... 68
ESPRIT LIVE VIDEO/SERVER PUSH PAGE CONTENTS ............................................................. 69
ADVANCED FEATURES ...................................................................................................................... 70
AUTOMATIC CONNECTION FEATURE ...................................................................................... 70
VIDEO MOTION DETECTION FEATURE ..................................................................................... 70
ALARM NOTIFICATION BY E-MAIL .......................................................................................... 71
RECORD AND PLAY BACK THE DISPLAY ON A PC .................................................................. 71
RECORDING THE DISPLAY .............................................................................................. 72
PLAYING BACK THE RECORDING .................................................................................... 72
FIRMWARE UPLOAD ................................................................................................................ 73
TROUBLESHOOTING .......................................................................................................................... 74
BASIC FUNCTIONING ............................................................................................................... 74
GREEN POWER LED ......................................................................................................... 74
ETHERNET LEDS .............................................................................................................. 75
COM LED ......................................................................................................................... 75
OUTPUT LEDS .................................................................................................................. 75
INPUT LEDS ..................................................................................................................... 75
VIDEO LEDS ..................................................................................................................... 76
TERMINAL PROGRAM .............................................................................................................. 76
TROUBLESHOOTING A TCP/IP NETWORK USING A PING UTILITY......................................... 76
TROUBLESHOOTING CONNECTION PROBLEMS ..................................................................... 77
TROUBLESHOOTING THE VIDEO CONNECTION ...................................................................... 77
TESTING THE AUDIO CONNECTION ........................................................................................ 78
TEST BETWEEN NET104A AND NET101R-A .................................................................. 78
TEST BETWEEN NET104A AND PC ................................................................................. 78
4
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS ............................................................................................................................... 79
GLOSSARY ......................................................................................................................................... 81
APPENDIX A – CONNECTING PELCONET NET104A TO VARIOUS COMPONENTS ........................... 84
CONNECTING PELCONET TO VARIOUS COMPONENTS WITH ASSORTED KEYBOARDS ...... 85
CONNECTION SCENARIO 1 ............................................................................................. 85
CONNECTION SCENARIO 2 ............................................................................................. 87
CONNECTION SCENARIO 3 ............................................................................................. 89
CONNECTING PELCONET TO THE COM IN RS-232 PORT ON A GENEX MULTIPLEXER ......... 91
CONNECTING A PELCONET RECEIVER TO A SYSTEM CM9502 ............................................. 92
CONNECTING PELCONET TO A CM9502 ASCII SERIAL PORT ................................................. 93
CONNECTING PELCONET TO A CM6700 AND KBD200A FOR REMOTE ASCII CONTROL ...... 94
CONNECTING PELCONET TO A CM6700 ASCII PORT ............................................................. 95
CONNECTING PELCONET TO A CM9760-DT FOR REMOTE BROWSER CONTROL ................. 96
CONNECTING PELCONET TO CM9760 EQUIPMENT FOR REMOTE COMMUNICATION ......... 97
CONNECTING A PELCONET TRANSMITTER TO THE CM6800 ASCII PORT ............................ 99
CONNECTING PELCONET TO A CM6800 AND KBD200A FOR REMOTE ASCII CONTROL ..... 102
APPENDIX B – FREQUENTLY ASKED QUESTIONS (FAQS) ............................................................... 105
INDEX ............................................................................................................................................... 108
WARRANTY AND RETURN INFORMATION ........................................................................................ 111
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
5
LIST OF ILLUSTRATIONS
Figure
Page
1
2
3
4
5
6
7
8
9
Front Panel LEDs .................................................................................................................. 14
Rear Panel Connectors ......................................................................................................... 15
Connecting Cameras Or Monitor ......................................................................................... 16
Connecting To The LAN Port ................................................................................................ 17
Connecting Power ................................................................................................................ 18
PelcoNet NET104A Home Page ........................................................................................... 21
Configuration For Box-To-Box Connections ......................................................................... 22
LAN Box-To-Box Connection (Transmitter, Receiver, Fixed Camera) ................................... 24
LAN Box-To-Box Connection (Transmitter, Receiver, Spectra III™) ..................................... 24
10 LAN Browser-To-Box Connection (Transmitter, Browser, Fixed Camera) ............................ 25
11 LAN Browser-To-Box Connection (Transmitter, Browser, Spectra III) .................................. 25
12 LAN Browser-To-Box Connection (Transmitter, Browser, Spectra III, Genex®) .................. 26
13 WAN Box-To-Box Connection (Transmitter, Receiver, Fixed Camera) ................................. 26
14 WAN Box-To-Box Connection (Transmitter, Receiver, Spectra III) ....................................... 27
15 WAN Box-To-Box Connection (Transmitter, Receiver, Spectra III, Genex) ........................... 27
16 WAN Browser-To-Box Connection (Transmitter, Browser, Fixed Camera)........................... 28
17 WAN Browser-To-Box Connection (Transmitter, Browser, Spectra III) ................................ 28
18 WAN Browser-To-Box Connection (Transmitter, Browser, Spectra, Genex) ........................ 29
19 Control Terminal Port Pin Assignments in RS-232 Mode .................................................... 31
20 Data Port Pin Assignments In RS-232 Mode ....................................................................... 32
21 Alarm Connections .............................................................................................................. 33
22 PelcoNet NET104A Menu Tree ............................................................................................ 39
23 PelcoNet Home Page ........................................................................................................... 40
24 PelcoNet NET104A Transmission System Setup Page ........................................................ 41
25 General Settings Configuration Page .................................................................................. 42
26 Screen For Entering The Password ...................................................................................... 45
27 Network Settings Configuration Page ................................................................................. 46
28 Video Settings Configuration Page ...................................................................................... 48
29 Audio Settings Configuration Page ..................................................................................... 52
30 Alarm Settings Configuration Page ..................................................................................... 54
31 Interface Settings Configuration Page ................................................................................ 60
32 ActiveX Dialog Box .............................................................................................................. 62
33 Device Controls Page ........................................................................................................... 63
34 Matrix Control Page ............................................................................................................. 65
35 Genex Control Page ............................................................................................................. 66
36 Spectra Control Page ........................................................................................................... 68
37 Esprit Control Page .............................................................................................................. 69
38 DB9 Cable Wire Splicing ..................................................................................................... 84
39 KBD300A (Direct Mode) Connected to a Receiver or Spectra Dome System ..................... 85
40 KBD4000 Connected to a Multiplexer ................................................................................. 87
41 CM9760KBD Connected to a CM9760-CC1 Controller ........................................................ 89
42 Connecting PelcoNet to Genex Using the COM IN RS-232 Port ......................................... 91
43 Using PelcoNet with CM9505 to Provide Remote Control .................................................. 92
44 Using PelcoNet with CM9502 to Provide Remote Control .................................................. 93
45 Using PelcoNet with CM6700 to Provide Remote Control .................................................. 95
6
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
46 Using PelcoNet with CM9760-DT to Provide Remote Control of a 9760 Monitor Output .. 96
47 Using PelcoNet to Transmit Data and Video Between 9760 Nodes ................................... 97
48 Using PelcoNet to Receive Data and Video Between 9760 Nodes..................................... 98
49 Using PelcoNet with CM6800 to Provide Remote Control ................................................. 100
50 Manager Screen ................................................................................................................. 101
51 Menu Screen ....................................................................................................................... 101
52A Using PelcoNet with CM6800 and KBD200A to Provide Remote Control ......................... 103
52B Using PelcoNet with CM6800 and KBD200A to Provide Remote Control ......................... 104
LIST OF TABLES
Table
Page
A
B
C
D
E
Terminal Command Reference ............................................................................................. 36
General Settings .................................................................................................................. 43
Network Settings ................................................................................................................. 46
Video Settings ...................................................................................................................... 49
Audio Settings ..................................................................................................................... 53
Alarm Settings ..................................................................................................................... 55
Interface Settings ................................................................................................................ 61
F
G
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
7
IMPORTANT SAFEGUARDS AND WARNINGS
Observe the following WARNINGS before installing and using this product.
1. Installation and servicing should be done only by qualified service personnel and conform to all
local codes.
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is
designed for indoor use only and it must not be installed where exposed to rain and moisture.
3. If the unit requires 100/230 VAC and does not have an on/off switch, the input power circuit
must have a circuit breaker.
4. The installation method and materials should be capable of supporting four times the weight of
the unit.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage
constituting a risk of electric shock is present
within this unit.
CAUTION:
RISK OF ELECTRIC SHOCK.
This symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
DO NOT OPEN.
Please thoroughly familiarize yourself with the information in this manual prior to installation and
operation.
UNPACKING INSTRUCTIONS
Unpack and inspect all parts carefully. Save the shipping carton, boxes, and inserts. They are the
safest manner in which to make future shipments.
If an item appears damaged in shipment, replace it properly in its box and contact the factory at 1-
800-289-9100 or 1-559-292-1981 for a replacement. (International customers fax 1-559-348-1120
for authorization and instructions.)
If an item needs to be returned to the factory for repair, consult the WARRANTY AND RETURN
section of this manual for instructions.
8
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCTIONS FOR THE NETWORK ADMINISTRATOR
The PelcoNet™ NET104A Multimedia Transmission System allows live video transmission to be
viewed over TCP/IP-based networks. This section is intended to help the network administrator
know what is involved with installing this product and how it will affect the network. The person
installing the product will need the following information about the network to make the product
function properly.
THE TRANSMITTER
•
•
•
•
•
A valid IP address* for each PelcoNet NET104A Transmission System unit
Subnet mask*
Default gateway (if applicable)
E-mail server’s IP address (if applicable)
Dedicated maximum allowable amount of bandwidth for live video**
* = Required for the PelcoNet NET104A Transmission System to function properly.
** = The PelcoNet NET104A Transmission System requires a continuous amount of bandwidth to
display true live video. Pelco recommends using switching hubs with the product so the
amount of bandwidth available to each unit is constant and reliable.
C2900M-B (1/03)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
THE BROWSER
If you plan to use a web browser to view live video across the network, there are procedures to
complete before you can use the browser. If you installed Internet Explorer 5.5 from the CD that
came with the PelcoNet NET104A Transmission System, you can skip the following. Otherwise,
complete the following before trying to use the browser.
1. Internet Explorer 5.5 or higher must be installed before continuing.
2. Set the computer’s display settings to use 16- or 32-bit color. (This is required for the live video
feature to function properly.)
3. Click the Start menu in Windows®.
4. Click Run.
5. In the open box, type D:/PACTIVEX.EXE (where D:/ = your CD ROM drive letter).
6. Click OK.
7. Follow the on-screen setup instructions to finish installing the plug-in.
MINIMUM REQUIREMENTS
•
•
•
PC with Windows 95/98/NT/2000/XP
Gateway to the network
Microsoft® Internet Explorer 5.5 or free serial interface and terminal program or PelcoNet
receiver and video monitor
•
Screen resolution of 800 x 600 pixels or higher, 16- or 32-bit pixel color resolution
10
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS THE PELCONET NET104A TRANSMISSION SYSTEM?
The PelcoNet NET104A Transmission System is technology that lets you view video from four
sources in real time across a LAN (local area network) and even WANs (wide area networks). This
technology is based on the TCP/IP protocol suite and Ethernet technology, providing compatibility
with today’s networking standards.
(See the Glossary section for definitions of terms used in this manual.)
HOW DO LANs AND WANs WORK?
•
A LAN consists of multiple computers connected together, sharing information. This
information could be files, e-mail, printers, or–with the PelcoNet NET104A Transmission
System–even live video and audio.
•
•
A WAN consists of multiple LANs connected over a great distance (for example, the Internet).
In any network environment, each computer needs an address so other computers on the
network know how to reach it.
It is similar to a city with street addresses. For the post office to deliver mail to your house, you
need a unique street address for the mail carrier to find you. A network is like the city. Like a
street address, the IP address on your computer is your address on the network. The IP address
is how other computers can find you on the network.
Remember that the IP address must be unique on the network.
•
•
When there are multiple networks and you are using the TCP/IP protocol, there must be a way
to communicate between the two networks. A physical device called a router is required. The
router’s IP address is referred to as the default gateway IP address.
A cable that connects one computer to another is like a city street you can use to get from one
house to another. The cable lets you communicate with each other on the network. This cable
is Category 5 cable with RJ-45 connectors at each end. (It looks like a phone cord, only slightly
larger.)
WHO SHOULD INSTALL THE PELCONET NET104A TRANSMISSION
SYSTEM?
NOTE: Consult your network administrator if you need help.
Installation is a matter of configuring an IP address using a standard terminal program or any Internet
browser and connecting the PelcoNet NET104A Transmission System to the Ethernet network. You
should have the following background and experience to configure and install these units:
•
•
Working knowledge of basic network management concepts and terminology
Working knowledge of tools and procedures for installing and operating sensitive electronic
equipment
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
11
OVERVIEW
NOTE: This manual refers to the PelcoNet NET104A Transmission System when discussing features,
functions, or specifications that apply to the transmitter. “Receiver,” as used in this manual, refers to
a PelcoNet NET101R/R-A Transmission System receiver unless otherwise noted.
DESCRIPTION
The four-channel PelcoNet NET104A Transmission System lets you transmit live video, audio, and
data from four sources over existing Ethernet computer networks (either intranet or Internet) using
the TCP/IP protocol. The NET104A can multiplex to provide a single view or quad view. You can
view the pictures on a CCTV or PC monitor.
The NET104A is a transmitter and is the only unit required to use the PelcoNet NET104A Transmis-
sion System. The transmitter connects any four NTSC or PAL video sources (cameras, for example)
to the computer network.
Depending on how you want to display the video, you can use a transmitter and a PC or a
transmitter and a NET101R/RA receiver. There are two ways to display remote video:
•
•
A hardware receiver and attached standard NTSC or PAL monitor
Web browser using any PC on the network to display the video
A NET104A transmitter and NET101R receiver can form a standalone system for data transfer
without a PC. The system can be extended to include additional transmitters and receivers so video
sequences from one transmitter can be received by several receivers simultaneously.
Transmitters and receivers are identified by IP addresses, just like any other equipment connected
to a computer network.
There is a bi-directional serial interface for remote control of peripherals like PTZ cameras. The
NET104A transmits full-duplex audio.
In appropriately configured networks, the multicast function permits the simultaneous video
transmission in real time to several NET101R/RA receivers. For this to work, the ICMP (multicasting
protocol) must be implemented in the network.
12
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
SOFTWARE VERSION
This manual documents PelcoNet NET104A software version 5.70.
PACKAGE CONTENTS
The following are supplied:
Qty
1
Description
NET104A model with plug-in power pack
1
Power cord
1
Power supply adapter (model specified with order; refer to the Specifications section in
this manual for model number)
1
1
PelcoNet peripheral device control cable
Wall mount kit
1
Mount bar
2
4
Machine screws
Wood screws
4
Plastic molly fasteners
1
CD
Keep the carton, including the original packaging material, to repack the equipment if you need to
return it for repair.
MODELS
NET104A
Four-channel video transmitter with integrated Ethernet connection. The NET104A
has a separate plug-in power pack. The NET104A functions as a data server only for
transmitting data.
Optional Compatible Products
NET101R
Single-channel video receiver with integrated Ethernet connection
NET101R-A Single-channel video receiver with bi-directional audio and integrated Ethernet
connection
C2900M-B (1/03)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT PANEL LEDs
ᕡ ᕢ ᕣ ᕤᕥᕦ
VIDEO
INPUTS
OUTPUTS
COM
ETHERNET
POWER
NET104A
Key:
1
2
3
4
5
=
=
=
=
=
Video LEDs light green when the corresponding input is active.
Input LEDs light red with active alarm and light green when ready.
Output LEDs light green when the corresponding relay is switched.
COM LED lights yellow when data is transmitted over the serial interface.
One Ethernet LED lights green when the unit is connected to the network. The other flashes
yellow when data packages are transmitted.
6
=
Power LED lights green when ready.
Figure 1. Front Panel LEDs
14
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR PANEL CONNECTORS
ᕤ
ᕣ ᕥᕦ ᕧ ᕨ
ᕡ ᕢ
ᕩ
A
LARM
A
LARM
OUTUTS
1
V
IDEO1
V
IDEO2
V
IDEO3
V
IDEO4
AUDIO
I
NPUTS
C
OM
5
1
+
2
+
3
+
4
+
+5V
2
3
4
P
OWER
I
N
O
UT
75
O
HM
ON
12V~0.8A
GND
GND
RS232/422/485
10/100 BASE-T
Key:
1
2
=
=
Four BNC video inputs for connecting the video sources
DIP switches (75 ohms when ON) for terminating the corresponding video input if the video
signal is not connected to additional video equipment
3
4
5
6
7
=
=
=
=
=
3.5 mm monaural audio input jack for connecting the audio source
3.5 mm monaural audio output jack for connecting a loudspeaker
Input terminals for connecting alarm sensors or switches
Output terminals for switching external devices (for example, lamps)
COM serial interface—9-pin D-sub connector (male)—for transmitting control data and for
configuring with the terminal program
8
9
=
=
Ethernet RJ-45 jack for connecting with the network
Power jack for connecting the plug-in power supply
Figure 2. Rear Panel Connectors
NOTE: Use only the supplied power plug. If the cable or connector show any sign of damage, do not
use the plug. Send it in for repair or replacement. Never try to use any power plug except the supplied
one.
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
15
QUICK INSTALLATION GUIDE
Follow the next six steps for the fastest way to get your product operating.
STEP 1: CONNECTING A CAMERA OR MONITOR
ᕡ
TRANSMITTER
A
LARM
A
LARM
OUTPUTS
1
V
IDEO1
V
IDEO2
V
IDEO3
V
IDEO4
AUDIO
I
NPUTS
C
OM
5
1
+
2
+
3
+
4
+
+5V
2
3
4
P
OWER
IN
O
UT
ᕣ
75
O
HM
ON
12V~0.8A
GND
GND
RS232/422/485
10/100 BASE-T
ᕢ
RECEIVER
V
IDEO-OUT
H
ANDSET
TRANSP.DATA
AUDIO-OUT
ᕤ
Key:
1
2
3
4
=
Cameras or other video sources with composite PAL or NTSC output
Video monitor with composite PAL or NTSC input
NET104A transmitter
=
=
=
NET101R/RA Receiver
Figure 3. Connecting Cameras Or Monitor
•
To connect the cameras, plug one end of a standard coaxial cable into a BNC connector (start
with video 1) on the rear of the NET104A and the other end into the camera. You can use any
video source with a composite PAL or NTSC output.
•
•
Set the DIP switches on the NET104A to position 75 OHM ON (down) to terminate the inputs
when the video signal is not connected to additional video equipment through a T-connection.
To connect a monitor to the NET101R/R-A receiver, plug one end of a standard coaxial cable
into the BNC connector on the NET101R/R-A and the other end into the monitor. You can use
any PAL or NTSC video monitor with a composite PAL or NTSC input.
For more information about video sources and monitors, see the Hardware Installation section.
16
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 2: CONNECTING ADDITIONAL ITEMS
Connect any additional items, such as alarms, audio, etc.
STEP 3: CONNECTING TO THE LAN PORT
ᕢ
ᕡ
ᕣ
A
LARM
A
LARM
OUTPUTS
1
V
IDEO1
V
IDEO2
V
IDEO3
V
IDEO4
AUDIO
I
NPUTS
C
OM
5
1
+
2
+
3
+
4
+
+5V
2
3
4
P
OWER
I
N
O
UT
75
O
HM
ON
12V~0.8A
GND
GND
RS232/422/485
10/100 BASE-T
Key:
1
2
3
=
=
=
Ethernet (10BASE-T) LAN connection to hubs, network, PCs (RJ-45 connector)
Ethernet Cat5 cable
Transmitter
Figure 4. Connecting To The LAN Port
To connect to the Ethernet network, use a standard UTP Cat5 cable with RJ-45 connectors. Plug
one end of the cable into the RJ-45 receptacle labeled “Ethernet.” The connection to a 10BASE-T
network can be made directly via a hub or switch.
C2900M-B (1/03)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 4: CONNECTING POWER
ᕢ
A
LARM
A
LARM
OUTPUTS
1
V
IDEO1
V
IDEO2
V
IDEO3
V
IDEO4
AUDIO
I
NPUTS
C
OM
5
1
+
2
+
3
+
4
+
+5V
2
3
4
P
OWER
I
N
O
UT
ᕡ
75
O
HM
ON
12V~0.8A
GND
GND
RS232/422/485
10/100 BASE-T
Key:
1
2
=
=
Transmitter
AC power plug adapter
Figure 5. Connecting Power
The transmitter and receiver have no main power switch. Insert the power cable plug into the
power jack on the unit until it latches. Plug the other end into the wall socket.
The green POWER LED on the front of the unit lights up, showing the unit is ready for operation.
When the network is connected properly, the green ETHERNET LED lights.
18
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP 5: SELECTING AN IP ADDRESS FOR YOUR NETWORK
NOTE: Consult your network administrator for a valid IP address.
The NET104A comes with the default address 192.168.0.1. while a NET101R/R-A receiver’s default
address is 192.168.0.2. Before operating the system inside your own network, you need to set a
valid IP address.
Use a terminal program attached at the RS-232 control terminal port to change the IP address.
Refer to the Configuration Using A Terminal Program section for a description of IP address
configuration using a terminal program.
STEP 6: USING A PC’S WEB BROWSER TO CONFIGURE THE NETWORK
Configure the network using a web browser. Start your web browser and connect to the URL http://
IP-Address, where IP-Address is the IP address of the unit you want to configure. Use the
standard dot-separated format (x.x.x.x.) to enter the address.
Refer to the Configuration Using A Web Browser section for detailed configuration instructions.
STEP 7: WHAT IS NEXT?
The system essentially is ready to use at this point. What you do now is up to you. For example,
you can connect to the web browser to watch one or more camera views or configure additional
options (alarms, default gateways, etc.) on the configuration pages.
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
19
TYPICAL APPLICATIONS
DISPLAYING REMOTE VIDEO ON A WEB BROWSER
The NET104A transmitter uses Motion-JPEG video compression or high performance H.323 coding
for transmitting across the network. This enables transmission to standard web browsers of either
live video (Live Video mode) or a stream of still images (Server Push mode).
•
To activate the Live Video feature, click Live Video above the video window on the PelcoNet
NET104A Transmission System home page (see Figure 6). The unit transmits using the H.323
coding format for display in the browser.
To stop Live Video, click any other option at the top of the page.
•
To activate the Server Push feature, click Server Push above the video window on the home
page. The unit continuously grabs snapshots to be JPEG encoded, transferred, and displayed
continuously by the browser.
To stop Server Push, click any other option at the top of the page.
The PelcoNet NET104A Transmission System can display live video to an infinite number of users
at a time (multicasting) or up to five users at a time (multi-unicasting). A sixth user connecting to
the same transmitter in a multi-unicast configuration cannot receive live video. In a unicast
configuration, only one user at a time can receive live video.
Server Push can support multiple users simultaneously on the same transmitter. Image quality is
good with an update rate of one image about every 2 to 10 seconds depending on the number of
users and available bandwidth.
Browsers that do not support live video technology can display an updated still image or a stream
of images in Server Push mode.
20
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 6. PelcoNet NET104A Home Page
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
21
DISPLAYING VIDEO VIA A TRANSMITTER-TO-RECEIVER CONNECTION
CAMERA
TRANSMITTER
A
LARM
A
LARM
OUTPUTS
1
V
IDEO1
V
IDEO2
V
IDEO3
V
IDEO4
AUDIO
I
NPUTS
C
OM
5
1
+
2
+
3
+
4
+
+5V
2
3
4
P
OWER
I
N
O
UT
75
O
HM
ON
12V~0.8A
GND
GND
RS232/422/485
10/100 BASE-T
RECEIVER
V
IDEO-IN
HANDSET
TRANSP.DATA
AUDIO-OUT
LAN/WAN
TCP/IP
INTRANET/INTERNET
MONITOR
Figure 7. Configuration For Box-To-Box Connections
There are two ways to make a high performance multimedia transmission system for computer
networks:
•
•
One way is to use just the NET104A transmitter and connect it through the computer network
to a PC with a web browser at the receiving end.
Another way is to connect the NET104A transmitter through the computer network to a
NET101R/R-A receiver. This is often called a box-to-box connection because it uses two
PelcoNet units.
In either case, routing dedicated cables from a camera to a monitor is not required because you can
use the existing computer network for that purpose.
22
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
The following explains a box-to-box connection.
1. First, transmitter (NET104A) and receiver (NET101R/R-A) need to be configured appropriately. If
the units are supposed to be operated in different subnets, a gateway IP address must be
configured. Use the alarm IP address field to address the destination. Also, the transmitter’s
video standard must be set to H.261. Enter the settings using either a terminal program or a
web browser.
You also must disable Internet proxy settings. To do so: In Internet Explorer, click the Tools
button, Internet Options, the Connections tab, and the LAN Settings button. Then remove
the check mark in the Use a proxy server box. Click OK, and then OK again.
2. Once all addresses are configured, type c in the terminal window to establish the actual
connection or program the live video receive IP and enable the live auto connect setting
through the web browser. Make sure the alarm IP address in the unit that will initiate the
connection points to the destination unit. After a few seconds, video transmission begins and
the camera scene appears on the monitor attached to the receiver.
Instead of using a terminal program for establishing a connection, you can attach a contact to
the alarm input. Make sure the alarm input is enabled.
You can use a web browser to connect to either of the two units, even during an active box-to-box
connection. This way you can make changes to the configuration and immediately see the result of
the setting (for example, when changing video quality). If you are connected to the transmitter, the
camera pictures are sent to the receiver and web browser simultaneously. There will be a short
break in the video display on the receiver monitor whenever the web browser requests a new
frame. This is especially noticeable with the Server Push feature.
Full-duplex audio can be transmitted in parallel with the video transmission in units equipped to
handle audio. To do so, you need to use the web browser to enable audio on the Audio Settings
configuration page.
Transparent data is always transmitted automatically between the two units as soon as the
connection becomes active. Data bytes entering the interface are transported to the other end
transparently. There is no flow control mechanism for the data channel. Overflowing the serial
interface will cause data loss.
To sever the connection from either end, type d in the respective terminal window (or disable the
alarm).
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
23
DIAGRAMS OF TYPICAL APPLICATIONS
SERVER
HUB
TRANSMITTER
RECEIVER
HANDSET
VIDEO-IN
TRANSP.DATA
AUDIO-OUT
VIDEO
INPUTS
OUTPUTS
COM
ETHERNET
POWER
NET104A
AUDIO
AUDIO
DATA
DATA
CAMERA
MONITOR
Figure 8. LAN Box-To-Box Connection (Transmitter, Receiver, Fixed Camera)
SERVER
HUB
TRANSMITTER
RECEIVER
HANDSET
VIDEO-IN
TRANSP.DATA
AUDIO-OUT
VIDEO
INPUTS
OUTPUTS
COM
ETHERNET
POWER
NET104A
VIDEO
AUDIO
DATA
AUDIO
DATA
VIDEO
MONITOR
KEYBOARD
SPECTRA
Figure 9. LAN Box-To-Box Connection (Transmitter, Receiver, Spectra)
24
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVER
HUB
TRANSMITTER
VIDEO
INPUTS
OUTPUTS
COM
ETHERNET
POWER
NET104A
BROWSER
CAMERA
Figure 10. LAN Browser-To-Box Connection (Transmitter, Browser, Fixed Camera)
SERVER
HUB
TRANSMITTER
VIDEO
INPUTS
OUTPUTS
COM
ETHERNET
POWER
NET104A
VIDEO
DATA
BROWSER
SPECTRA
Figure 11. LAN Browser-To-Box Connection (Transmitter, Browser, Spectra)
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
25
SERVER
HUB
TRANSMITTER
VIDEO
INPUTS
OUTPUTS
COM
ETHERNET
POWER
NET104A
VIDEO
DATA
GENEX
BROWSER
SPECTRA
Figure 12. LAN Browser-To-Box Connection (Transmitter, Browser, Spectra, Genex®)
1 OR MORE PCs
1 OR MORE PCs
CLOVIS
SERVER
NEW YORK
SERVER
ROUTER
ROUTER
HUB
HUB
RECEIVER
VIDEO-IN
TRANSMITTER
HANDSET
TRANSP.DATA
AUDIO-OUT
VIDEO
INPUTS
OUTPUTS
COM
ETHERNET
POWER
NET104A
VIDEO
VIDEO
AUDIO
AUDIO
CAMERA
MONITOR
Figure 13. WAN Box-To-Box Connection (Transmitter, Receiver, Fixed Camera)
26
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
1 OR MORE PCs
1 OR MORE PCs
CLOVIS
SERVER
NEW YORK
SERVER
ROUTER
ROUTER
HUB
HUB
RECEIVER
VIDEO-IN
TRANSMITTER
HANDSET
TRANSP.DATA
AUDIO-OUT
VIDEO
INPUTS
OUTPUTS
COM
ETHERNET
POWER
NET104A
VIDEO
VIDEO
AUDIO
DATA
AUDIO
DATA
MONITOR
SPECTRA
KEYBOARD
Figure 14. WAN Box-To-Box Connection (Transmitter, Receiver, Spectra)
1 OR MORE PCs
1 OR MORE PCs
CLOVIS
SERVER
NEW YORK
SERVER
ROUTER
ROUTER
HUB
HUB
RECEIVER
VIDEO-IN
TRANSMITTER
HANDSET
TRANSP.DATA
AUDIO-OUT
VIDEO
INPUTS
OUTPUTS
COM
ETHERNET
POWER
NET104A
VIDEO
VIDEO
DATA
DATA
MONITOR
GENEX
KEYBOARD
SPECTRA
Figure 15. WAN Box-To-Box Connection (Transmitter, Receiver, Spectra, Genex)
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
27
1 OR MORE PCs
1 OR MORE PCs
CLOVIS
SERVER
NEW YORK
SERVER
ROUTER
ROUTER
HUB
HUB
TRANSMITTER
VIDEO
INPUTS
OUTPUTS
COM
ETHERNET
POWER
NET104A
VIDEO
VIDEO
CAMERA
BROWSER
Figure 16. WAN Browser-To-Box Connection (Transmitter, Browser, Fixed Camera)
1 OR MORE PCs
1 OR MORE PCs
CLOVIS
SERVER
NEW YORK
SERVER
ROUTER
ROUTER
HUB
HUB
TRANSMITTER
VIDEO
INPUTS
OUTPUTS
COM
ETHERNET
POWER
NET104A
DATA
VIDEO
BROWSER
SPECTRA
Figure 17. WAN Browser-To-Box Connection (Transmitter, Browser, Spectra)
28
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
1 OR MORE PCs
1 OR MORE PCs
CLOVIS
SERVER
NEW YORK
SERVER
ROUTER
ROUTER
HUB
HUB
TRANSMITTER
VIDEO
INPUTS
OUTPUTS
COM
ETHERNET
POWER
NET104A
VIDEO
DATA
GENEX
BROWSER
SPECTRA
Figure 18. WAN Browser-To-Box Connection (Transmitter, Browser, Spectra, Genex)
C2900M-B (1/03)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
HARDWARE INSTALLATION
Refer to Appendix A – Connecting PelcoNet NET104A To Different Components for diagrams that
show various connections.
CONNECTING VIDEO SOURCES OR DISPLAYS
Up to four video sources can be connected to the NET104A.
1. To connect cameras, plug a standard coaxial cable into a BNC connector (start with video 1) on
the rear of the NET104A and the other end into the camera. You can use any video source (for
example, a VCR) with a composite PAL or NTSC output. The inputs accept color or black and
white sources and automatically detect whether they are PAL or NTSC. The video inputs have
an internal termination of 75 ohms.
2. Set the DIP switches to position 75 OHM ON (down) to terminate the inputs when the video
signal is not connected to additional video equipment through a T-connection.
CONNECTING AUDIO EQUIPMENT
The NET104A provides an audio channel via the audio in and out jacks.
1. Connect the microphone to the AUDIO IN jack.
2. Connect the loudspeaker to the AUDIO OUT jack. (This is not required if you are using the
speakers on your PC.)
The audio signals are transmitted bi-directionally and simultaneously with the video signals. This
allows control of a loud speaker or door intercom system, for example, at the monitored location.
30
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING DATA TERMINALS
The NET104A has a serial interface that can be configured on the Interface Settings configuration
page for terminal control or transparent data: RS-232 or RS-485, etc.
Use As Control Terminal Port
For local control and configuration of the unit, you can connect a data terminal (for example, a PC
running a standard terminal program) to the serial interface labeled COM on the NET104A. The
9-pin D-sub connector can be connected to a PC’s COM port.
You can use a standard terminal program to communicate with the unit. The default parameters are
set to 19200 baud, 8 bits of data, 1 stop bit, and no parity (8N1).
To access the online help, type ? (a question mark) in the terminal window. For more information on
the command set, see the Configuration section. This mode allows the control port to be used to
send serial data that requires flow control.
You can configure the RS-485 half-duplex mode in the web browser. The RTS and CTS signals are
enabled for flow control.
If this RS-485 mode is chosen, the camera control data is transferred to this port. Certain cameras
with fixed data length require the buffered RS-485 mode. (This half-duplex mode is not required for
interfacing to any Pelco product.)
Pin Name Direction
Description
1
2
3
4
5
6
7
8
9
DCD
RXD
TXD
DTR
GND
DSR
RTS
CTS
–
Input
Input
Data Carrier Detect
Receive Data
Transmit Data
Data Terminal Ready
Ground
VIEWED FROM SOLDERING
SIDE OF PLUG
Output
Output
1
2
3
4
5
Input
Output
Input
–
Data Det Ready
Ready To Send
Clear To Send
–
6
7
8
9
Figure 19. Control Terminal Port Pin Assignments in RS-232 Mode
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Use As Transparent Data Port
The serial interface offers a transparent serial data channel between the receiver and the
transmitter. A typical application for transparent data is remote control of peripheral equipment (for
example, a dome system with PTZ functions). You also can use this channel to control remotely any
external device with a serial interface. The serial data is transferred in parallel to the video and
audio data.
Transmission of transparent data is enabled only after a video connection has been established.
Also, the RS-232 interface for the transparent data port does not support hardware flow control.
For proper operation, you must configure the following in a way that they fit the associated unit:
baud rate, parity of the interface of the PelcoNet NET104A Transmission System unit, and number
of data and stop bits. Use a web browser to configure these parameters at the unit with the
configuration side.
The transparent data interface is used to control PTZ cameras remotely, to transmit data transpar-
ently between two units, or to control equipment connected to a PC COM port. Transmission of
transparent data is possible only when the units are connected. Only the data transmitting signals
are provided at this port.
Pin Name Direction
Description
1
2
3
4
5
6
7
8
9
–
RXD
TXD
–
N.C.
Receive Data
Transmit Data
N.C.
VIEWED FROM SOLDERING
SIDE OF PLUG
Input
Output
1
2
3
4
5
GND
–
Ground
N.C.
–
N.C.
6
7
8
9
–
N.C.
–
N.C.
Figure 20. Data Port Pin Assignments In RS-232 Mode
32
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING EXTERNAL SENSORS
The unit has four alarm inputs that let you connect external signaling devices, like door contacts or
motion detectors. If configured accordingly, an alarm trigger can, for example, set up an automatic
connection between NET104A and the remote station. You can connect switches or contacts
directly without a separate power supply.
Connection INPUT 5 is a master alarm. This connection lets you activate or bar (for example, by
means of a key-operated switch) all the alarm triggers.
NOTE: Do not connect the ground terminals to earth ground. External switching voltage must not
exceed 12 VDC.
The four alarm inputs are optically isolated from the other components of the NET104A via
optocouplers and require a voltage of 5-12 VDC for switching.
Do the following to connect external sensors. Refer to Figure 21.
NET 104A
A
LARM
A
LARM
V
IDEO1
V
IDEO2
V
IDEO3
V
IDEO4
AUDIO
I
NPUTS
O
UTPUTS
4
C
OM
5
1
+
2
+
3
+
4
+
+5V
1
2
3
P
OWER
I
N
O
UT
75
O
HM
ON
12V~0.8A
GND
GND
RS232/422/485
10/100 BASE-T
ACTIVE
LOW
+5V
ARM
A
LARM
NPUTS
OUTPUTS
5
1
+
2
+
3
+
4
+
+5V
1
2
3
4
ACTIVE
HIGH
+5V
GND
GND
Figure 21. Alarm Connections
1. Pull the terminal block INPUTS from its plug-in base.
2. Attach the conductors to the alarm input and ground terminals. (Push a small screwdriver or
similar instrument into the square opening. This opens the circular opening. Insert the wire into
the circular opening, and then remove the screwdriver.)
3. Push the terminal block back on to the plug-in base.
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
33
CONTROLLING PERIPHERAL DEVICES
The NET104A has four relay outputs for switching external devices (for example, lights or sirens).
The relays can be operated interactively, during an active connection, or automatically to coincide
with certain events. Settings for the relay must be configured (see the Configuration section).
Typical applications of the relay outputs are activating electric door openers or switching of lights
and other electrical devices. Do not exceed the maximum rating of 24V and 0.8A.
Do the following to connect peripheral devices. Refer to Figure 2.
1. Pull the terminal block OUTPUTS from its plug-in base.
2. Attach the conductors to the pairs of relay terminals.
3. Push the terminal block back on to the plug-in base.
CONNECTING TO A LAN
To connect to a 10BASE-T network, plug a standard UTP/Cat5 cable with RJ-45 connectors into the
receptacle labeled ETHERNET on the NET104A. You can connect directly to the Ethernet network.
The green Ethernet LED on the front of the unit (refer to Figure 1) lights as soon as the connection
to the network is correct physically and synchronized with the LAN. Check the cable or see the
Troubleshooting section if the LED does not light.
The second Ethernet LED flashes yellow when data packages are transmitted.
CONFIGURATION
There are two ways to configure your system:
•
The most basic control and configuration is accomplished by connecting a terminal to the
RS-232 terminal port.
•
A more convenient, complete configuration and display of video is through the built-in HTTP
server, which connects to any standard web browser. This is the recommended method.
CONFIGURATION USING A TERMINAL PROGRAM
Using a terminal program (for example, the Windows application HyperTerminal) connected to the
RS-232 terminal port on the unit’s rear panel provides limited configuration and control capabilities
(null modem cable required). Ensure that the PC’s COM port is set up properly (default parameters
are 19200 baud, 8N1) and that the local terminal echo is disabled.
All commands consist of single characters you type inside the terminal window. Enter only one
command at a time and do not terminate this input by pressing the Enter key. After entering a value
(for example, an IP address), check the entered characters again and only then press Enter to
transmit the values to the NET104A.
Do the following:
1. First, disconnect the NET104A from the network.
2. Connect the D-sub COM jack on the NET104A to a free serial port on the PC.
3. Click the Start button on your PC’s desktop, and then select Programs from the Start menu.
4. Highlight Accessories. Click HyperTerminal.
5. Double-click Hypertrm.exe to open HyperTerminal.
6. Type the name for the new connection in the Name field. Click OK.
34
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Change the Connect using field to the COM port of the computer to which you have
connected the serial cable. Click OK.
8. Change the Bits per second field to 19200.
9. Change the Flow control field to None. Click OK.
10. Hold the Shift key and press the ? key to bring up the Help menu.
11. Press the I key to set the IP address. Type the new IP address PelcoNet will be using on the
network. Press ENTER.
12. Press the S key to set the subnet mask. Type the new subnet mask. Press ENTER.
13. Press the G key to set the gateway IP address. Type the new gateway IP address. Press ENTER.
14. Close HyperTerminal. If prompted to save settings, click OK.
The following section shows a typical terminal session.
Typical Session
The help screen appears as follows in the terminal window:
* * * * * * * * * * * * * * * * * * * * *
Help menu
?
i
this site
set the IP address
s
g
a
c
d
D
m
v
b
t
set the subnet mask
set the gateway IP address
set the alarm IP
connect to alarm IP
disconnect from alarm IP
disconnect all connections
display MAC address
display version information
display current transmission data rate
toggle DHCP on/off
disable ‘local echo’ for a better display!
* * * * * * * * * * * * * * * * * * * * *
NOTE: You cannot use backspace during a terminal session—if you mistype a character, end your
entry by pressing Enter and try again. If you see duplicate characters on any entry, the “local echo”
feature of your PC’s terminal program is not disabled.
If you are using the terminal to set up the unit’s IP address, just type i and you are prompted to
enter a new IP address:
i
->Enter new IP address (old:192.168.0.1): 192.168.0.5 (Enter)
->IP address set to 192.168.0.5
If you want to establish a live video connection to a remote unit, you have to specify the remote IP
address by typing a and entering the remote IP address in the same manner as the unit IP address
as shown in the example above.
To establish a connection, type c; to disconnect, type d.
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Command Reference
The following table gives an overview of all available commands. (Enter the appropriate informa-
tion where indicated by the quotation marks below. Do not enter the quotation marks.)
Table A. Terminal Command Reference
Cmd Description
?
i
Displays the help screen.
Set up a new IP address.
->Enter new IP address (old:192.168.152.160): ‘new
IP address’ [Enter]
->IP address set to <new IP address>
s
g
a
Set up a new subnet mask.
->Enter new subnet mask (old:255.255.255.0): ‘new
subnet mask’ [Enter]
->subnet mask set to <new subnet mask>
Set up a new gateway IP address.
->Enter new gateway IP address (old:192.168.0.10):
‘new gateway IP address’ [Enter]
->gateway IP address set to <new gateway IP address>
Set up a new alarm IP to connect to.
->Enter new alarm IP address (old:192.168.0.3): ‘new
alarm IP address’ [Enter]
->Alarm IP address set to <new alarm IP address>
c
Connects a live video to the specified alarm IP.
->connecting . . .
connected
PelcoNet tries to call the alarm IP host
PelcoNet has established the connection
d
Disconnects any pending video connection.
->disconnecting . . .
disconnected
PelcoNet disconnects
PelcoNet has disconnected
36
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
D
m
v
Closes the connection from the connecting IP address.
->Close connection from <IP address>
Display the unit’s MAC address.
->MAC address: <unit’s MAC address>
Display version information.
->HW version: <version number> SW version: <version
number>
b
t
Displays the current transmission data rate. The display is updated continuously.
Toggles the DHCP (Dynamic Host Configuration Protocol) on/off.
->DHCP on
->DHCP started
->DHCP BOUND <IP address, subnet, gateway>
or
->DHCP off
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
37
CONFIGURATION USING A WEB BROWSER
In addition to the aforementioned configuration using a terminal program, which only covers the
most basic settings, a web browser is the tool of choice for a more complete configuration. To
accomplish this, the system features a complete HTTP server.
Microsoft Internet Explorer 5.5 is the recommended browser.
Web Server Concept
1. Start your web browser.
2. Connect to the URL http://IP-Address, where IP-Address is the IP address of the unit you want
to configure. Use the standard dot-separated format (x.x.x.x.) to enter the address. The home
page is displayed with the video from input 1 being shown.
The HTTP server provides six separate pages for configuration.
You can return to the home page from any other page by clicking on the PelcoNet logo on the left
side. Clicking the Pelco® logo while on the home page immediately transfers you to the Pelco
Internet home page, provided the network allows for Internet access.
In order for live video images to be decoded, the special ActiveX control file must be installed on
your PC. The latest version of ActiveX comes on the PelcoNet CD.
NET-Manager
NET-Manager is a program that can make it easier to configure PelcoNet units in local networks.
The program and manual (C2901M) are on the resource CD that comes with your PelcoNet unit.
Refer to the manual for instructions.
38
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Guide To The Menu Structure
*
GENERAL
Name
ID
Password level
Password
Date
Time
Time zone
Time server IP
Hardware
Software
Firmware update
Configuration download
Configuration upload
MATRIX CONTROL**
WITH
LIVE VIDEO
*
NETWORK
IP address
Subnet mask
MATRIX CONTROL**
WITH
SERVER PUSH
Gateway IP address
DHCP
Base Port
Mail server IP address
Mail reply address
Multicast Group IP
Time to live (Multicast)
Enable Multilink H.323
Enable Multicast Streaming
Multicast Video port
GENEX MUX**
WITH
LIVE VIDEO
*
VIDEO
Video quality
GENEX MUX**
WITH
SERVER PUSH
Video standard
Video resolution
Video Priority
Video bandwidth ActiveX
Network Interface bandwidth
Camera 1 - 4 name
Name stamping
SPECTRA DOME**
SYSTEM WITH
LIVE VIDEO
LIVE VIDEO**
Time stamping
Time slice
JPEG Size
JPEG File name
FTP server IP address
Login name
Password
SPECTRA DOME**
SYSTEM WITH
SERVER PUSH
Path
SERVER PUSH**
*
AUDIO
Input level
Output level
HOME**
ESPRIT **
WITH
LIVE VIDEO
Coding mode
CONTROL**
*
ALARM
Video alarm
Motion alarm
ESPRIT**
WITH
SERVER PUSH
Alarm input pin 1 - 4
Master Alarm input pin
Camera Follows alarm input
Alarm status
Connect
SETUP**
Live video receive IP
Live video auto connect
Send email
Idle state
Operating mode
Relay follows
Relay Names
* = CONTROLLED BY SERVICE PASSWORD
** = CONTROLLED BY USER PASSWORD
Trigger Relay
*
INTERFACE
Com ports
Baudrate
Data bits
Parity
Stop bits
RS232/485
Halfduplex mode
00944
Figure 22. PelcoNet NET104A Menu Tree
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
39
PelcoNet NET104A Home Page
Figure 23. PelcoNet Home Page
The home page is the starting point for any configuration.
The window in the center of the screen is the display area for decoded video.
•
•
Clicking the Pelco logo on any page connects you to the Pelco Internet home page (provided the
LAN supports Internet access).
Click Live Video to choose a live display or Server Push for periodically updated stills.
•· Click Control to access an options screen with links to pages where you can see and control
the displayed view. (Refer to the Web Browser Control Pages section.)
•
Click Setup to access an options screen with links to configuration pages. Click any icon on the
side to transfer to the desired page.
40
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 24. PelcoNet NET104A Transmission System Setup Page
NOTE: When changing any configuration item in one of the following pages, make sure to change a
single item at a time. Then click the respective Set button. If more than one item needs to be changed,
execute the procedure repeatedly. If more than one item is changed without clicking the Set button in
between, only the entry associated with the clicked button is actually changed. All other entries
return to their previous settings.
All configuration items are stored in non-volatile memory so they are kept when the unit is
powered down.
Some configurations apply only to transmitters (for example, camera settings) while others apply to
receivers. Also, the settings require a receiver unit with the audio option (NET101R-A). All settings
not expressly restricted to certain models apply to all.
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
41
General Configuration Page
The unit name and ID, as well as password settings, comprise the General Settings configuration
page.
All units have a real-time clock set during manufacture. However, time and date can be changed
any time; for example, when the units are operated in different time zones.
Version numbers for the hardware and the firmware are for information only. Whenever you need
technical support, have these numbers ready.
Figure 25. General Settings Configuration Page
42
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table B. General Settings
Configuration Default
Description
Item
Setting
(Unit) Name
none
The unit Name and unit ID identify the device from a distance;
for example, in the event of an alarm call. The name helps when
there are many PelcoNet units on the network.
Enter a name (nine characters maximum) for the NET104A that
lets the device be easily identified. With appropriate configura-
tion, the name will be displayed in the video window.
(Unit) ID
none
none
The ID serves as a machine-readable name. The ID can be read
at any time. Reading is facilitated remotely via UDP/IP, letting a
management system monitor the unit.
Password
level
Transmitters operate at two authorization levels: service or user.
This field lets you set the password at either level.
At the service level, you can change all the configuration
settings. At the user level, you can operate but not configure the
device. You can have a live picture or see the configuration
settings but you cannot change them.
Password
none
The unit can be password-protected to prevent unauthorized
tampering with the configuration. The password needs to be
repeated correctly in the confirm box before password protection
is activated. If the device is not protected with a password, “No
password set” will be displayed.
Once password protection is enabled, you need to log in before
the configuration pages can be accessed (Figure 26).
You can only change one of the two passwords. To change the
other, you have to access this configuration page again.
NOTE: If you forget the password and cannot access the unit,
refer to the red caution sheet that came with the unit. The sheet
details procedures for resetting the unit to allow access. Your
settings will be erased.
Date
n/a
n/a
Enter the current date in DD/MM/YYYY format. This is the
system date, driven by the internal real-time clock. The day of
the week (first entry box) need not be entered and will be
automatically adjusted based on the given date.
Time
Enter the current time or click the Synchronize button to
synchronize the NET104A with your computer’s system time. The
system time is driven by the internal real-time clock.
Time zone
Greenwich Use the pull-down menu to select the time zone for the current
Mean Time time.
(Continued on next page)
C2900M-B (1/03)
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Table B. General Settings (Continued)
Configuration Default
Item Setting
Description
Time server IP 0.0.0.0
Enter the IP address of an Internet server that will supply
accurate time for your PelcoNet unit(s). Or synchronize to a piece
of equipment on your network.
Hardware
Software
n/a
n/a
n/a
Read-only version number of the hardware. This contains unique
serial number, type of hardware, and revision.
Read-only firmware version number. This is important informa-
tion should you need technical support.
Firmware
update
Enter the name of the file containing new firmware, or locate it
using the Browse button. Then click the Upload button to
upload the firmware and install it on the system.
Configuration
download
n/a
n/a
Clicking the Download button saves the current configuration
of the PelcoNet NET104A Transmission System to a PC file.
Configuration
upload
This copies a file from a PC to the NET104A. Enter the name of
the file containing the configuration, or locate it using the
Browse button. Then click the Upload button to overwrite the
configuration with the configuration stored in the named file.
44
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
When password protection is on, as described in Table B, the program displays the following
password screen if any attempt is made to configure the unit (that is, selecting one of the
configuration pages).
Figure 26. Screen For Entering The Password
C2900M-B (1/03)
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Network Settings Configuration Page
Figure 27. Network Settings Configuration Page
Network and routing information make up the Network Settings configuration page. The following
table describes the configuration items.
Table C. Network Settings
Configuration Default Setting Description
Item
IP address
192.168.0.1
Enter a unique IP address that is valid for your network.
The pre-configured default IP address allows for easy
configuration in closed environments. You can use a
crossed cable to directly connect to a PC. Also, the PC’s IP
address and subnet mask must match the default IP
address.
NOTE: Changing the IP address also affects the current
browser connection. You will have to enter the new URL to
regain connectivity to the unit.
Subnet mask
Gateway IP
255.255.255.0
none
Enter a valid subnet mask for your network, if subnets are
in use.
Enter the IP address of the router. This is typically used in a
WAN environment.
(Continued on next page)
46
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table C. Network Settings (Continued)
DHCP
off
Dynamic Host Configuration Protocol. When set to on, the
network DHCP server automatically assigns your computer
an IP address. When set to off, you must assign it yourself.
Base Port
25000
Enter a setting to designate which TCP/IP ports PelcoNet
uses for transmission, video, audio, and control. For
example, the default setting of 25000 means PelcoNet will
use TCP ports 25000-25001 and UDP ports 25002-25011
(12 ports total) for all video and control data.
Mail server
IP address
none
none
Entry is only required if the mail-sending feature is to be
used. Outgoing e-mail is sent to the mail server (SMTP
server) at this IP address.
Mail reply
address
Enter a name for the NET104A that lets the device be
easily identified. This is similar to the unit identification
Name field on the General Settings configuration page.
This field identifies the device from a distance. The name
helps when there are many PelcoNet units on the network.
The recipient of the e-mail can identify the e-mail’s sender
by this entry.
Multicast
Group IP
0.0.0.0
This is the Multicast IP Address. (Network hardware–
such as switches, hubs, routers, etc.–must support the
multicasting protocol, ICMP.) This field sets PelcoNet to
use the multicasting protocol, which allows more efficient
use of bandwidth. The IP range is 224.0.1.0 through
238.255.255.255.
Time To Live
(Multicast)
1
This setting specifies how many routers an information
packet can go through before it expires.
Enable
Multilink H.323
Off
Off
When set to On, this setting lets the PelcoNet unit support
five simultaneous live video connections.
Enable
Multicast
Streaming
This setting, in conjunction with the Multicast Group IP and
Enable Multilink H.323 settings, can allow an unlimited
number of live video connections. The Enable Multilink
H.323 field, as well as this field, must both be set On for
this to work.
Multicast
Video port
60000
This setting designates the TCP/IP port PelcoNet uses for
video when using the multicasting protocol.
C2900M-B (1/03)
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Settings Configuration Page
The Video Settings configuration page lets you modify all video-related parameters. Some items
apply only to transmitters while others require a receiver. The screen capture below belongs to a
transmitter.
Refer to Table D for default settings and descriptions.
Figure 28. Video Settings Configuration Page
48
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
The following table details the configuration items.
Table D. Video Settings
Configuration
Item
Default Setting
Description
Video quality
super fast
You can set the quality of the video. On restricted
bandwidth channels, you need a compromise
between optimum image sharpness and quick
reproduction of movements in the image. With
increasing bandwidth, the effect of this setting
diminishes, as best quality and fast motion can be
maintained simultaneously.
With a high image refresh rate, sharpness deterio-
rates with increasing movement in the field of view.
If movement is expected in a small area only, you can
give preference to sharpness. The intelligent
compression process then is able to refresh the
affected areas in the image. The unchanged rest of
the image will be reproduced with optimum
sharpness.
With high bandwidths in the local network (above
200 Kb), you can work with maximum image quality
without the refresh rate suffering noticeably.
Video standard
H.263
This field sets the video standard for the transmis-
sion. If you intend to do a box-to-box connection, set
this to H.261, click the Set button, and then click the
Reboot link to reboot the unit. An hour glass symbol
indicates the command is being processed. This
symbol remains on the screen (regardless of whether
or not the reboot is finished) until you click another
function. The POWER LED flashes when the reboot is
finished.
If you are not near the unit, wait at least one
minute to ensure the reboot finishes. If you click
another function before the reboot concludes, the
program responds with a retry or firewall message.
Delete the message, exit the program, and restart.
Video resolution
standard (CIF)
Choose medium (QCIF) or standard (CIF) video
resolution. Common Intermediate Format (CIF) is at
352 x 288 picture elements. For very restricted
channels (for example, wireless or low speed modem
transmission) it may be advantageous to switch to
medium (QCIF) resolution at 176 x 144 pixels for
decent image rates.
(Continued on next page)
C2900M-B (1/03)
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Table D. Video Settings (Continued)
Configuration
Item
Default Setting
Description
Video Priority
ActiveX
This field controls whether performance of the device
is optimized for MJPEG or ActiveX (H.261/H.263).
If you select MJPEG mode, a sequence of still images
(for example, a fresh image every second) is
displayed in the browser. This setting does not
require any plug-ins or ActiveX installation and may
be advisable for severely limited channels (for
example, the Internet).
PelcoNet recommends choosing ActiveX for best
video performance. This provides the best quality and
lowest data rate consumption. When you choose this
the first time, the corresponding ActiveX is down-
loaded automatically to your PC from the Pelco home
page.
Video bandwidth 1000
ActiveX
This field controls the transmitter bandwidth setting
for live video. This value relates only to the video
transmission rate (without audio and protocol).
Receivers can log into the transmitter with a lower or
same data rate.
In streaming mode, this value indicates the data
transmission rate of the video. Select a video
transmission rate between 10 Kb/sec and 1 Mb/sec.
Network interface 1000
bandwidth
This field lets you adjust the maximum data rate that
will be sent over the network.
Enter the data transmission rate in kbits per second.
Valid entries are 10 through 1000.
The value is the maximum bandwidth for the video
data. Also, transmission bandwidth is needed for
data; to control cameras, for example. Therefore, an
actual transfer value can be over or under the
adjusted value.
Camera 1-4 names n/a
Enter the desired camera names (nine characters
maximum for each). Camera 1 is video 1 input. In
addition to the unit name, the camera names help the
user identify the locations or the visible scenes.
(Continued on next page)
50
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table D. Video Settings (Continued)
Name Stamping is a combination of unit name and
Name stamping
off
camera name (18 characters maximum). This
identifier can be stamped on the video image.
Choose top for upper left corner or bottom for lower
left corner to display the name information inside the
video image. Choose off if you do not want the
names displayed. (Note that when Name Stamping
and Time Stamping are assigned to the same
position, Name Stamping has priority and will
partially obscure Time Stamping.)
Time stamping
Time slice
off
Similar to name stamping, date and time information
can be stamped on the live video image at either the
upper or lower right corner. Stamping occurs at the
transmitter before the actual coding takes place.
Therefore, the name and date/time information are
an integral part of the coded and transmitted data.
0
Enter the time interval in seconds at which single
images should be sent for storage on an FTP server.
These images can be accessed later (for example, to
reconstruct alarm events). Enter 0 if no single images
are to be stored.
JPEG Size
M
This field designates the size of each JPEG image
that will be posted to the FTP server for storage.
JPEG file name
Overwrite
When you save a snapshot to your PC’s hard disk, this
field specifies whether the file gets overwritten by
the next save, or another file is created with a higher
number (Increment), or another file is created with a
Date/Time designator. The file name’s root is always
“snap.”
FTP server
IP address
0.0.0.0
Enter the IP address of the FTP server on which the
images will be stored.
Login name
Password
Path
n/a
n/a
n/a
Enter the login name used to access the FTP server.
Enter the password used to access the FTP server.
Enter the directory under which the images are to be
stored on the FTP server.
C2900M-B (1/03)
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Settings Configuration Page
Audio configuration settings apply only to the NET104A transmitter and to the NET101R-A receiver.
You can set the input and output levels (from 0-100%) on this configuration page. You can use the
Coding Mode menu item to set the sending side’s coding mode.
The audio decoder automatically follows the transmitter’s selected audio coding. If the receiver
cannot decode the selected mode, an automatic fall-back to the next available audio mode occurs.
Figure 29. Audio Settings Configuration Page
52
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
The table below details available configuration items.
Table E. Audio Settings
Configuration Item Default Setting Description
Input level
64%
Enter the sensitivity of the audio input. You need to
adapt the input sensitivity to the level of the audio
source to avoid overdriving the signal, causing
distortion. Experiment for the best setting.
Output level
Coding mode
32%
off
Enter the sensitivity of the audio output. Adapt the
output level to the requirements of connected
audio equipment.
Select the coding mode for audio data. Mode
G.711 supports all systems. Pick G.711 or off to
work without coding.
C2900M-B (1/03)
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Alarm Settings Configuration Page
The PelcoNet NET104A Transmission System is not only a multimedia gateway but also a security
device and, therefore, has many features related to security applications. The Alarm Settings
configuration page lets you configure your unit for video surveillance applications. This page
basically applies to transmitters only. However, receivers do provide the same features. In most
surveillance-related applications, the receiver is located in a secure alarm center-type environment
while the transmitter is mounted inside or at the location to be monitored. Refer to the Typical
Applications section for more information about remote video surveillance.
Figure 30. Alarm Settings Configuration Page
54
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
The set of video surveillance features is explained below.
Table F. Alarm Settings
Configuration Default Setting Description
Item
Video alarm
off
If you select on, the signal from the video source (the
camera in most cases) is monitored constantly for
interruption. If no signal is received, the NET104A
triggers the alarm.
Motion alarm
off
The system has a video motion detection feature.
The video scene is monitored constantly for relevant
motion.
To set motion detection, do the following:
1. Select on to trigger an alarm in the event of
movement.
2. Click the Configuration button to access the Motion
Detection screen. If you want to accept the factory
settings, click the Defaults button.
3. Use the Camera input pull-down menu to select the
camera view you want motion detection on.
4. Click the Select area button to display a window with
a grid superimposed on it. Select the cells in the image
you want the system to monitor for motion. To set an
individual cell, click it with the left mouse button (it will
turn red). Click with the right button to deselect a cell
(which will turn white). Select or deselect multiple
cells by holding down the left or right mouse button
and dragging. Release when finished.
5. Use the Motion tracking pull-down menu to turn
on/off tracking.
6. The Tracker box indicates and controls the direction of
motion detection. You can set motion detection to
operate in one direction only by removing the check
marks in the opposite direction.
(Continued on next page)
C2900M-B (1/03)
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Table F. Alarm Settings (Continued)
Configuration
Item
Default Setting
Description
7. Use the Local sensitivity slide bar to set
detection sensitivity. You need to adapt sensitivity
to the respective environment and the acceptable
false alarm rate: for a lower false alarm rate
select a lower sensitivity and vice versa.
Experiment to find the best setting. Use of the
motion detection feature is recommended only
indoors and under controlled lighting conditions.
8. Use the Average n[frames] slide bar to define
for how long or over how many pictures motion in
the scene must be detected before an alarm will
be released. If the value is low, even movement
over a small period triggers an alarm. If the value
is high, movement over a longer period is
required to trigger an alarm.
9. Use the Object min size [nxn blocks] slide bar
to designate the minimum number of cells in the
frame a moving object must fill to trigger an
alarm. You can set the value between 1*1 and
6*6 (2*2 is recommended). If the size of the
object in the picture exceeds the value you set,
motion detection triggers an alarm.
10. The Alarm indicator box lets you set a
threshold so an alarm is triggered only if the
sensitivity of the video sensor is exceeded. Thus,
something such as background noise caused by
the camera can be filtered to avoid unwanted
alarms.
Pull up or down on the blue line to observe the
motion detector. Set it straight above the basic
deviation of the red curve.
11. Press Default to get the default settings for
motion detection.
The following conditions must be met for motion
detection to function:
•
•
•
•
Motion detection must be activated.
At least one cell must be activated.
Sensitivity must be set higher than zero.
The master alarm may also have to be activated.
(Continued on next page)
56
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table F. Alarm Settings (Continued)
If external sensors or simple contacts or switches will
Alarm input
pin 1-4
off
be used with the system, you need to select the
alarm input.
Click on to activate alarm triggering via an external
sensor for the selected pin. Otherwise, click off.
You also can specify whether the alarm is triggered
by the voltage level active high (normally open) or
active low (normally closed).
In addition, you can enter a name (nine characters
maximum) for the selected pin in the Name field.
Master Alarm
input pin
off
You can use alarm input 5 as a master alarm; for
example, if a key switch is used to arm the system.
If you choose on, alarm input 5 must be active to
enable all other alarms.
Camera follows
alarm input
off
off
Select on to display the image of the corresponding
camera automatically when an alarm is triggered.
Choose off to keep the current camera display.
Alarm status
Current alarm activation status can be shown in the
video image (similar to the name, date, and time
stamping discussed in Table D).
If configured to be on, the status of the activated
alarms, namely, video, motion, and input, is shown in
the upper left corner of the video image. Or, the
display can be activated as soon as an alarm
condition is reached (choose on alarm). This way, the
video image corresponding to the alarm condition is
clearly marked.
Also, there is a choice to keep the status display,
once an alarm has been triggered, even when the
original cause of the alarm is no longer present
(choose hold display), or to have the status display
follow the alarm condition (choose hold off).
(Continued on next page)
C2900M-B (1/03)
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Table F. Alarm Settings (Continued)
Configuration
Item
Default Setting
Description
Connect
no
The alarm functions would have little effect without
automatically triggering corresponding actions. Select
yes for automatic connection to the given IP address.
The idea is to provide a remote monitoring station with
live video in case of an alarm.
This feature can be useful even for many applications
not related to alarm conditions. One example is a
video-equipped door entry system: when the doorbell
is pressed, a contact closes and the connected
transmitter autonomously connects to a receiver. Full-
duplex audio can provide verbal communication, while
the relay output can open the door remotely.
On receivers, the default alarm connection IP address
is set to 192.168.0.1 (default IP of transmitter).
Live video
receive IP
0.0.0.0
Enter the IP address of the transmitter or receiver to
be notified in the event of an alarm. If that remote unit
has a password, enter it in the Remote Password field
below so the two units can communicate with each
other.
Remote
password
empty
off
If applicable, enter the password to access a
transmitter (refer to the Live Video Receive IP field
above).
Live video
auto connect
Select on if at each restart an active connection
should be set up automatically to the IP address
defined above. Otherwise, select no.
The auto connect feature guarantees an active
connection to the given alarm IP address even after
connection breakdown or network failures. If you
select auto connect, the network cable can be pulled
at any time. As soon as the network comes back
alive, the connection is reinstated. On a receiver, this
feature is enabled to establish a connection to a
transmitter automatically.
Send email
off
Select on to send an alarm e-mail in the event of an
alarm. A person who does not have a video reception
device can thus be informed via an attached JPEG
image sent to the predefined e-mail address.
(Continued on next page)
58
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table F. Alarm Settings (Continued)
If applicable, enter the e-mail address where you
Receiver email
address
empty
open
want an e-mail sent in the event of an alarm.
Idle state
You can configure the switching behavior of each
built-in relay output at idle: open (N.O. at zero
current) or closed (N.C. at zero current).
Operating mode
Bistable
Select an operating mode for each relay.
•
When you select the default Bistable mode, the
relay will stay in the idle or active state for an
indefinite period. (For example, select Bistable if
a floodlight activated by an alarm is to remain
switched on at the end of the alarm.)
•
When you select Monostable mode, the relay
automatically falls back to the idle state after a
predefined period expires. (For example, select
Monostable 10s if a siren triggered by an alarm is
to sound for a period of 10 seconds.)
Relay follows
None
If necessary, select a particular event from the pull-
down menu that will trigger the relay. A typical
application is having the relay following the status of
the connection; for example, to power peripheral
equipment or even the camera itself. Select from the
following:
•
•
•
•
•
Motion alarm: Triggering by motion alarm
Input pin: Triggering by external alarm sensor
Video loss: Triggering by video signal alarm
Connection: Triggering at each connection setup
Remote input pin: Triggering by switching
contact of the remote station
•
None: No relay triggering by events
Relay Names
Trigger Relay
Relay 1-4
n/a
Assign a relay name to each output.
Clicking the appropriate Relay button switches that
relay by hand. Typical applications are opening
remote doors or operating lights.
C2900M-B (1/03)
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Interface Settings Configuration Page
You can use the Interface Settings configuration page to configure the parameters of the communi-
cation ports.
Figure 31. Interface Settings Configuration Page
60
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
The default parameters of the transparent data port agree with the most commonly used settings,
as shown in the following table.
Table G. Interface Settings
Configuration
Item
Default Setting
Description
Com ports
Terminal
This port can be set to Terminal mode, which is used
to program the unit through HyperTerminal.
Or, it can be set to Transparent, which allows
control of devices such as a digital video recorder
(DVR) or pan/tilt/zoom camera, etc. When set to
Transparent PelcoNet cannot be accessed through
HyperTerminal.
Baudrate
Data bits
Parity
19200
8
Select any transmission rate from 300 to 19200 baud.
Select the number of data bits (7 or 8) per character.
Select the type of parity check (Odd, Even, or None).
Select the number of stop bits (1 or 2) per character.
Select the required protocol for the port.
None
1
Stop bits
RS232/485
RS232
Halfduplex mode off
If you choose this RS-485 mode, camera control data
is transferred automatically to the control port, which
is a serial interface on the unit’s rear panel to which
you can connect a PC. This mode supports flow
control.
NOTE: In the “on” or “buffered” mode, transparent
data is rerouted to the control terminal port; terminal
functions are provided on the transparent data port.
C2900M-B (1/03)
61
Download from Www.Somanuals.com. All Manuals Search And Download.
LIVE VIDEO AND SERVER PUSH VIDEO PAGES
The Live Video page shows a real-time picture of a camera view with update rates and image
quality similar to a box-to-box configuration. It can be configured for bandwidth use and for various
image quality settings. The Server Push page shows still pictures that are updated periodically, and
image quality is fixed.
1. To access the PelcoNet NET104A Transmission System home page, you must first connect to
the Internet/intranet network and open Internet Explorer (the browser).
2. Then, enter the default address 192.168.0.1 in the address box. If this address has been
changed, enter the application address. The home page appears.
3. Click either Live Video or Server Page on the home page.
To exit either page, click an option at the top of the page.
The program displays dialog boxes when you try to view live video under any of the following conditions:
•
•
•
With a browser other than Internet Explorer
Without first installing ActiveX (Figure 32)
When your computer display is not set for 16- or 32-bit color
(To change: right click the desktop, and then click Properties, the Settings tab, and select
High Color [16 bit] or True Color [32 bit]. For NT, select 65536 Colors.)
•
When Microsoft Virtual Machine is not enabled.
(To enable: on the Tools menu select Internet Options, select the Advanced tab, locate
Microsoft VM, checkmark Java Console Enabled and JIT compiler for virtual machine
enabled. Reboot your PC.
With any of these conditions, you can only view the video as a series of still images.
Figure 32. ActiveX Dialog Box
62
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
WEB BROWSER CONTROL PAGES
ACCESSING THESE PAGES
1. To access the PelcoNet NET104A Transmission System home page, you must first connect to
the Internet/intranet network and open Internet Explorer (the browser).
2. Then, enter the default address 192.168.0.1 in the address box. If this address has been
changed, enter the application address. The home page appears.
3. Click Control to access the Device Controls page.
4. The Device Controls page has underlined links to the control pages. To access, click one.
Figure 33. Device Controls Page
C2900M-B (1/03)
63
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLLING THE DISPLAY
The live video control pages include representations of keys that let you control various functions
(in addition to showing the camera display). Use the mouse pointer and click the left mouse button
to enable options and operate controls on the screen. Click outside of the options to disable a radio
button or selection button.
Live video pages let you choose the size of the video viewing area. Click either 352x288 (small) or
704x576 (large) in the Resize Video field.
Live video pages also let you record and play back camera views on a PC’s hard drive. Refer to the
Record and Play Back the Display on a PC section for details.
On the Spectra and Esprit live video control pages, you can control the following:
•
•
Presets – To program a preset: select the camera by clicking its button, position the camera,
click the Set check box, and click a preset number button.
To activate a preset: click the camera button and then click a preset number button.
Patterns – You can program only one pattern per camera through PelcoNet. To program a
pattern: select the camera by clicking its button, click the Set check box, then click Start, and
then use the arrow buttons to position the camera. Click Stop to halt pattern programming.
To operate a pattern: select the camera, click Start to begin the pattern and Stop to halt.
•
Programming Menus – To access the programming menus: select the camera by clicking its
button, click the Set check box, and then click the 95 button. Use the camera arrow keys to
move up/down the menus. Use the open iris icon to open menus and set options. Use the open
iris icon in conjunction with the Exit option to move backward through menu layers and to exit
programming mode.
NOTE: If you installed Internet Explorer from the PelcoNet NET104A Transmission System CD, ActiveX
is already installed. Otherwise, you must install ActiveX before you can view the video. Refer to the
Instructions for the Network Administrator section.
NOTE: PTZ control always defaults to camera 1. Therefore, if you are viewing and controlling
camera 2, 3, or 4 and then exit, you will not have control of that camera when you return. You must
select again the camera you want to control.
64
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MATRIX CONTROL LIVE VIDEO/SERVER PUSH PAGE CONTENTS
Figure 34. Matrix Control Page
The Matrix Control pages contain the following:
•
•
•
•
•
•
•
•
•
•
•
Ten numbered buttons
CAM (camera) button
MON (monitor) button
CLR (clear) button
PRST (preset) button
PATT (pattern) button
MAC (macro) button
STOP button
BWD (backward) button
FWD (forward) button
PC hard drive record/playback control buttons beneath the live screen (refer to the Record and
Play Back the Display on a PC section for more information)
The following are arrayed under “Lens”:
•
•
•
Iris open and close buttons
Focus far and near buttons
Zoom out and in buttons
The following are arrayed under “Pan/Tilt”:
•
•
Eight direction arrow buttons
Home button in the center returns the camera to its starting position (preset 1 must be set for
the button to function)
The page also contains the following:
•
•
AUX ON button
AUX OFF button
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
65
GENEX LIVE VIDEO/SERVER PUSH PAGE CONTENTS
Figure 35. Genex Control Page
The Genex pages contain the following across the top of the page:
•
•
•
•
•
•
•
Main and Spot monitor selection radio buttons
A Live/VCR button
A Sequence button
A View button
A zoom button
A picture-in-picture button
Buttons for 4-, 9-, and 16-screen display
The following are arrayed down the right side of the page:
•
•
•
•
•
•
•
Radio buttons for 16 cameras
Iris open and close buttons
Focus far and near buttons
Zoom out and in buttons
Eight direction arrow buttons with a home button in the center
Ten numbered buttons to use with the Pattern button (enter preset number and click Pattern)
A Pattern button
PC hard drive record/playback control buttons are arrayed beneath the live screen (refer to the
Record and Play Back the Display on a PC section for more information).
66
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: You may not have control of the desired camera when switching between the spot and main
monitor radio buttons.
To control a camera and view it on the spot monitor:
1. Make sure you are viewing video on the main monitor.
2. Click the radio button for the camera you want to view on the spot monitor.
3. Click the radio button for the spot monitor.
If you do not follow this procedure, you may not have control of—or be viewing—the desired
camera on the spot monitor.
The following example shows what can happen if you do not follow the procedure:
1. Select camera 16 on the main monitor.
2. Select the spot monitor. You will view and control camera 16.
3. Select the main monitor. You will view camera 16.
4. Select camera 7. You will view camera 7 on the main monitor.
5. Select the spot monitor. You will view camera 7 on the spot monitor but control camera 16. To
view camera 16, return to the main monitor and select camera 16, then select the spot monitor.
Now you can view and control camera 16. If you select another camera (for example, 8), you
can control camera 8 but not view it. Return to the main monitor, select camera 8, and then
select the spot monitor. Now you can control and view camera 8.
NOTE: The View button on this page does not function the same way as the View button on the
Genex unit. You cannot enter multiplexer setup with the PelcoNet View button. You can, however,
enter multiplexer setup with the View button on the mulitplexer unit, and then on the PelcoNet screen
you can use the arrow buttons to navigate and the iris open button to make changes.
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
67
SPECTRA LIVE VIDEO/SERVER PUSH PAGE CONTENTS
Figure 36. Spectra Control Page
The Spectra pages contain the following arrayed down the left side:
•
•
Four camera selection buttons
A Mux button for putting the screen into quad view
The following are arrayed down the right side under “Lens”:
•
•
•
Iris open and close buttons
Focus far and near buttons
Zoom out and in buttons
The following are arrayed under “Pan/Tilt”:
•
•
Eight direction arrow buttons
Home button in the center returns the camera to its starting position (preset 1 must be set for
the button to function)
The following are arrayed under “Presets”:
•
•
•
Ten numbered preset buttons
A Set check box
A preset 95 button for entering the programming menus
The following are arrayed under “Pattern”:
•
•
A Start pattern button
A Stop pattern button
PC hard drive record/playback control buttons are arrayed beneath the live screen (refer to the
Record and Play Back the Display on a PC section for more information).
NOTE: When returning to this page, camera radio buttons 1-4 and the Mux button always show
camera button 1 selected even if another camera is being viewed.
68
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
ESPRIT LIVE VIDEO/SERVER PUSH PAGE CONTENTS
Figure 37. Esprit Control Page
The Esprit pages contain the following arrayed down the left side:
•
•
Four camera selection buttons
A Mux button for putting the screen into quad view
The following are arrayed down the right side under “Lens”:
•
•
•
Iris open and close buttons
Focus far and near buttons
Zoom out and in buttons
The following are arrayed under “Pan/Tilt”:
•
•
Eight direction arrow buttons
Home button in the center returns the camera to its starting position (preset 1 must be set for
the button to function)
The following are arrayed under “Presets”:
•
•
•
Ten numbered preset buttons
A Set check box
A preset 95 button for entering the programming menus
The following are arrayed under “Pattern”:
•
•
•
A Start pattern button
A Stop pattern button
A Wiper button
PC hard drive record/playback control buttons are arrayed beneath the live screen (refer to the
Record and Play Back the Display on a PC section for more information).
C2900M-B (1/03)
69
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED FEATURES
AUTOMATIC CONNECTION FEATURE
The advantage of conventional dedicated cabling lies in guaranteed performance and availability.
The PelcoNet NET104A Transmission System’s auto-connect feature is designed to provide the
same level of guaranteed connectivity expected from analog coaxial video cables.
IT networks commonly experience short breakdowns and congestion. Protocols used for computer
communication (for example, TCP/IP) are designed to cope with missing data and interruptions.
With the PelcoNet NET104A Transmission System, once a video connection is established, the
video stream normally terminates gracefully when a network connector is pulled or the network is
otherwise disrupted.
The system can be configured to reconnect automatically to guarantee connectivity. To activate this
feature, click the Connect radio button to On (in the Alarm Settings configuration page) and
confirm this choice by clicking the Set button. Now the unit will try to connect to the specified
alarm IP address every time. The receiving station (alarm IP address) can be another receiver.
VIDEO MOTION DETECTION FEATURE
The transmitter can check video input automatically for significant motion in the scene and trigger
an alarm if the motion exceeds a preset threshold. Activate motion detection by setting Motion
Detection to on in the Alarm Settings configuration page.
Click the Configuration button to select parameters for motion detection. You need to tailor these
parameters to the particular application. Experiment to find the best settings. For example, higher
sensitivity may lead to erroneous detection and increase false alarms.
You can restrict motion detection to certain areas in the scene. Select the cells you want the
system to monitor for motion. To set an individual cell, click it with the left mouse button (the cell
will turn red). Click with the right mouse button to deselect a cell (which will turn white). Select or
deselect multiple cells by holding down the left or right mouse button and dragging. Release when
finished.
70
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
ALARM NOTIFICATION BY E-MAIL
The e-mail feature lets you send an e-mail message to a recipient on any alarm event. This could
be used to signal an alarm to people who cannot be reached with a video-based notification.
To activate this feature, enable at least one of the alarm inputs, configure a receiver e-mail
address, and activate the Send Email button. Remember to configure a mail server and gateway IP
addresses on the General Settings configuration page.
Now the system will send an e-mail to the specified recipient on every alarm event. There will be a
timeout of at least 30 seconds before the same alarm event generates another e-mail message.
The e-mail will contain the status of the four alarm inputs so you can see which event triggered the
e-mail.
RECORD AND PLAY BACK THE DISPLAY ON A PC
Live video control pages let you record the camera display on a PC’s hard drive and play it back
later. The file is recorded on the hard drive of the PC on which you are viewing the picture. The
controls are a row of buttons beneath the screen.
NOTE: Audio is not saved to the AVI file. Consequently, there is no audio on playback.
– These buttons jump the display to the beginning or ending of the recording in playback
mode.
– These buttons incrementally move the display backward and forward while the display
is paused in playback mode.
– This button stops the recording or playback.
– This button pauses the recording or playback.
– This button plays the recording.
– This button starts the recording.
AVI
– This button is used to designate a location for saving the recording.
– This button is used to load a recorded file for playback.
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
71
Recording The Display
Do the following to record the camera display:
1. Access a live video control page (by clicking Control on the Home page, and then clicking one
of the underlined links to a live video control page).
2. Select a camera.
3. Position the camera as desired (if it has PTZ capability).
4. Click the
button. The Choose Directory window opens.
5. Select a location in which to save the recording. Click OK.
6. Click the
7. Click the
button to begin recording.
AVI
button to halt recording. The recording is saved automatically.
Playing Back The Recording
You can play back the camera recording either through the Windows Media Player or in PelcoNet
through the browser. Do the following to play back the camera recording through the browser:
1. Access a live video control page (by clicking Control on the Home page, and then clicking one
of the underlined links to a live video control page).
2. Click the
button. A directory window opens.
3. Select the directory where the file you want is located. Click the file to select it, and then click
Open.
4. Click the
button to begin playback.
To advance or reverse the playback, first click the
button. Each click of a
or
button moves the recording a few frames. To move to the beginning or end of the recording,
click a
or
button. Click the
button to resume playback.
5. Click the
clicking the
button to halt playback and return to live video. You can replay the recording by
button.
72
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
FIRMWARE UPLOAD
Units have flash EPROMs for firmware upgrades in the field. These upgrades can be done directly
from the web browser.
Do the following to upload firmware using the web browser:
1. Obtain the latest PelcoNet NET104A Transmission System firmware from Pelco
(http://www.pelco.com).
2. Use the browser to select the General Settings configuration page of your unit.
3. Use the Browse button in the Firmware update field to select the correct new firmware file.
4. Click the Upload button.
5. After about 30 seconds you should get a feedback message from the connected unit.
6. The message “upload complete – WAIT” confirms the correct upload of the new firmware,
which is now being installed. The alarm input LEDs will flash back and forth between red and
green to indicate installation.
WARNING: Do not disconnect power to the unit for any reason while firmware is being in-
stalled. Disrupting the cycle will damage the flash EPROM. If this occurs, you will have to return
the unit for repair.
When all the alarm input LEDs turn green, reprogramming is complete and the unit cycles
power.
7. If you try to upload an invalid firmware file, you will get the message “Upload Failed.”
8. If you revisit the General Settings configuration page after the firmware is uploaded
successfully, you will see the message “New Firmware Installed.”
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
73
TROUBLESHOOTING
If the following instructions fail to solve your problem, contact Pelco Technical Support at
1-800-289-9100 for help. You should have the serial number from the bottom of the unit and the
firmware version ready in case they are needed.
Do not try to personally repair a unit. Opening it immediately voids any warranty. Leave mainte-
nance and repairs to qualified technical personnel. Swap a defective unit with a replacement unit
and return the defective one for repair.
BASIC FUNCTIONING
LEDs on the unit indicate its condition. The following sections describe malfunctions indicated by
the LEDs.
Green Power LED
Green Power LED Is Off
If the green power LED on the front panel is off and you believe it should be blinking, check the
following:
•
•
•
•
Make sure the enclosed power supply is connected correctly to the power plug socket.
Make sure the power supply is connected correctly to a functioning power outlet.
Check the power cord for apparent damage.
Check the power supply for a 5 VDC output. If it is correctly connected and the green power
LED still does not light, exchange the power supply for a new one.
Green Power LED Blinks Slowly
This does not indicate a malfunction but means a connection exists between one unit and another.
Connections with a web browser have no effect on this LED, so there will be no blinking light
during configuration.
Green Power LED Lit
This indicates the NET104A is on but there is no connection.
Green Power LED Stays Off After Firmware Upload And Reprogramming
If the power LED does not come back on after a firmware upload, there may have been a problem
during upload. Return the system to the dealer.
Closely follow the instructions for the firmware upload. Especially do not disconnect the power
supply during firmware upload and reprogramming.
74
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
Ethernet LEDs
The green Ethernet LED should light when the Ethernet connection is made. If this LED is off:
Green Ethernet LED Is Off
•
Make sure the network cable is firmly connected to the hub or switch.
•
Does the hub or switch work correctly in the network? Check the power supply of the hub or
switch.
•
•
Use a Cat5 straight-through cable to connect to a normal hub. Check the cable for physical
damage.
Use a crossover cable if connecting a unit directly to a PC without a hub.
Yellow Ethernet LED Is Flashing
The yellow LED flashes briefly whenever a unit transmits a data packet (for example, when
accessing the unit with a web browser). If this LED fails to come on, perform the following checks:
•
Are all units connected correctly with the power supply? Check power supplies and
connections.
•
•
•
Did you configure the correct IP address for your unit?
Is your web browser configuration correct?
Is the TCP/IP protocol installed on your PC operating system, and is an IP address assigned to
the PC?
•
Are the subnet mask and gateway properly set up?
Contact your network administrator if you have problems installing your network.
Com LED
This green LED should flash when data is transmitted via serial interface.
Output LEDs
If green LED is lit, then the alarm output is switched. If not lit, then the output is inactive (idle
state).
Input LEDs
If the LED is not lit, then the alarm input is inactive.
If the LED is lit green, then the alarm input is activated. If lit red, then the alarm is triggered.
If the LED changes from red to green, then program memory is being deleted (during firmware
upload). The programming progress is indicated by the alternating green lighting of all five LEDs.
C2900M-B (1/03)
75
Download from Www.Somanuals.com. All Manuals Search And Download.
Video LEDs
When lit green, these LEDs indicate the corresponding video input is selected. (In multiplexer
mode, the LEDs change automatically in quick succession.)
TERMINAL PROGRAM
If the terminal program fails to connect to the unit’s terminal port, check the following:
•
Is the right COM-port interface on the PC selected for the terminal program, and are the
settings correct? Is the cable connected to the terminal and not the data port on the unit?
Program default settings are 19200 kb/s, 8 data bits, no parity, 1 stop bit (8N1) for the terminal
program.
•
•
If the data exchange between the terminal program and the system still does not work, check
the serial cable. Does the system answer when you enter a question mark?
Disable the local echo if you see duplicate characters on your screen.
TROUBLESHOOTING A TCP/IP NETWORK USING A PING UTILITY
(Enter the appropriate information where indicated by the quotation marks below. Do not enter the
quotation marks.)
To see if a unit in your network can be reached, try to ping your unit by typing the following
command in a DOS window:
c:\>ping ‘unit IP address’
If it is reached, there will be a response like the following:
Reply from <IP address>: bytes=32 time=NN ms TTL=xxx
If the LAN path is malfunctioning, the ping command will time out. If so, you could have one of the
following problems:
•
•
Wrong physical connections. Make sure the green Ethernet LED is on. See the Basic
Functioning section for more information.
Wrong network connection. Verify the IP address is entered correctly and that subnet mask and
gateway address are set properly.
Otherwise, ask your network administrator.
76
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING CONNECTION PROBLEMS
If you fail to connect to a system from a hardware receiver, check the following to pinpoint the
problem:
•
•
Do not connect two units of the same type (for example, receiver to receiver).
Make sure network connectivity is available (for example, by using the ping command as
described above).
TROUBLESHOOTING THE VIDEO CONNECTION
If no video or a distorted video image is displayed at the receiver during a connection to a
transmitter:
•
Make sure to use the right unit for your application: a camera can be connected only to a
transmitter, never to a receiver.
•
•
Make sure the camera is switched on and the coaxial cable is connected to the transmitter.
Check the camera cable and connect a video monitor to the camera to check that the camera is
functioning correctly.
•
•
•
At the receiving system, make sure the monitor is switched on and the coaxial cable is
connected to the receiver.
Check the monitor cable and the selection of the monitor channel, if the monitor features more
than one video channel.
If the monitor can display only a single video standard (PAL or NTSC), check the setting of the
video output format on the Video Settings configuration page.
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
77
TESTING THE AUDIO CONNECTION
This test procedure applies only to NET104A and NET101R-A units.
Test Between NET104A And NET101R-A
1. Connect a microphone (via a preamplifier) to the Audio In jack and a loudspeaker to the Audio
Out jack on the NET104A. Connect a microphone to the Line-In RCA jack and a loudspeaker to
the Line-Out cinch connectors on the NET101R-A.
2. Make sure the correct menu items are set on the Audio Settings configuration page of both
systems; that is, select the appropriate interface (line I/O).
3. Switch the coding mode to G.711 or G.728.
4. Select a volume above zero.
5. After establishing the Ethernet connection, audio should be transmitted both ways.
6. Be sure the level is not set too low and that the right interface is selected.
7. If you cannot hear any audio, check the microphone and loudspeaker together with other audio
equipment, and make sure the microphone is switched on if it has a power switch.
Test Between NET104A And PC
1. Connect a microphone (via a preamplifier) to the Audio In jack on the PelcoNet unit. Connect a
microphone to the PC.
2. Make sure the correct menu items are set on the Audio Settings configuration page; that is,
select the appropriate interface (line I/O).
3. Switch the coding mode to G.711 or G.728.
4. Select a volume above zero.
5. Connect a loudspeaker to the PC’s sound card. Connect another loudspeaker to the Audio Out
jack on the PelcoNet unit. After establishing the Ethernet connection, audio should be
transmitted both ways. Press the F12 key on the PC and speak into the microphone; audio
should be heard on the PelcoNet loudspeaker. Release the key to hear audio from the PelcoNet
unit.
6. Be sure the level is not set too low and that the right interface is selected.
7. If you cannot hear any audio, check the microphone and loudspeaker together with other audio
equipment, and make sure the microphone is switched on if it has a power switch.
78
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
NETWORK PROTOCOL AND STANDARDS COMPATIBILITY
Internet Configuration
Video Coding
Video Frame Rate
IP, TCP, UDP, ICMP, ARP, DHCP, HTTP, FTP, IGMP
H.261/263, H.323 (M-JPEG in Server Push mode only), G.711
Up to 30 images/second
INTERFACES
Video Input (transmitter) 4 BNC, PAL/NTSC, 75 ohms, 1 Vp-p, RS-170, CCIR-601
Audio Input
RCA phono jack, -32 dBm0, variable
Audio Output
LAN Interface
LAN Data Rate
Data Interface
Alarm Inputs
Alarm Output
RCA phono jack, -10 to 0 dBm0, 600 ohms
UTP (10/100BASE-T auto-sensing), RJ-45
10 Kbps up to 1 Mbps
1 RS-232C/RS-422/RS-485, bi-directional (9-pin, D-sub)
4 terminals for direct connection of controls, 1 master alarm input
4 relays, maximum 24V, 0.8A
VIDEO
Video Standards
Video Image Size
PAL, NTSC
704 x 576 pixels (high resolution)
352 x 288 pixels (CIF)
POWER ADAPTER
Type
Input Voltage
Output Voltage
Plug power adapter
100-240 VAC, 50/60 Hz
12 VAC, 800 mA
Country-Specific Adapters US (default), Australia, Europe, and UK. (Specify when ordering.)
NOTE: For countries other than the United States, you must also specify the appropriate transformer
adapter when ordering. Please refer to the list below. (Adapter will be sent at no charge.)
NETPLUG4-AU
NETPLUG4-EU
NETPLUG4-UK
NETRANS4
Transformer adapter, Australian.
Transformer adapter, European.
Transformer adapter, United Kingdom.
Replacement transformer, 100-240 VAC.
C2900M-B (1/03)
79
Download from Www.Somanuals.com. All Manuals Search And Download.
MISCELLANEOUS
LED Displays
17 LEDs (video, inputs, outputs, Ethernet, connection, power)
ENVIRONMENTAL
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
41° to 104°F (5° to 40°C)
80% maximum relative humidity, non-condensing
-4° to 140°F (-20° to 60°C)
95% maximum relative humidity, non-condensing
GENERAL
Dimensions
Unit Weight
1.4 (H) x 10.2 (W) x 6.5 (D) inches (3.5 x 26.0 x 16.5 cm)
2.8 lb (1.3 kg), without power supply
Shipping Weight
4.1 lb (1.9 kg), with power supply
CERTIFICATIONS
•
•
•
CE, Class B
cTUVus
FCC, Class A
OPTIONAL ACCESSORIES
NET101R
NET101R-A
Single-character video receiver with integrated Ethernet connection
Same as NET101R plus audio function
80
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY
10BASE-T
IEEE 802.3 specification for 10 Mbs Ethernet
Address Resolution Protocol
ARP
b/s
Bits per second, the actual data rate
Cat5 Cable
Type of cable used on a LAN to connect computers, printers, and
transmitters and receivers to a hub on the network
CIF
Common Intermediate Format; video format with 352 x 288 pixels
The router’s IP address (for example, 192.168.0.1)
Dynamic Host Configuration Protocol
Default Gateway
DHCP
DNS
Domain Name Service
FTP
File Transfer Protocol
Full Duplex
G.711, G.728
H.224
Simultaneous data transmission in both directions
Standard audio coding algorithms defined by ITU-T
Standard protocol for data communication and remote control
Standard motion video coding algorithm defined by ITU-T
Standard for M-JPEG video and audio compression defined by ITU-T
Hypertext Transfer Protocol
H.261
H.323
HTTP
HTML
Hypertext Markup Language
Hub
A device on the network that connects multiple computers together to
form a LAN
ICMP
Internet Control Message Protocol
ID
Identification: machine-readable number or name
Institute of Electrical and Electronics Engineers
IEEE
Internet Protocol
The main protocol used on the Internet. Forms—in conjunction with the
Transfer Control Protocol (TCP)—the TCP/IP protocol suite
C2900M-B (1/03)
81
Download from Www.Somanuals.com. All Manuals Search And Download.
IP
See Internet Protocol
IP Address
A unique four-byte number that identifies each unit on the Internet or
network. Usually written in dotted-decimal notation with periods
separating the bytes. This address is required to communicate on the
network (for example, 192.168.0.100).
ISP
Internet Service Provider
JPEG
Joint Photographic Expert Group (procedure to encode still images)
See Local Area Network
LAN
Local Area Network
Multiple computers linked together into a network to share information
within a limited geographic area (such as a building or a campus)
controlled by a network operating system and using a transport protocol
MAC Address
NAT
Media Access Control/hardware address
See Network Address Translator
Network Address
Translator
A proposal for IP address re-use where the local IP address is mapped
to a globally unique address
Picture
PPP
A video picture that has been digitized at a particular resolution
See Point-To-Point Protocol
Point-To-Point Protocol A protocol allowing a computer using TCP/IP to connect directly to the
Internet
Router
A physical device that connects multiple LANs
QCIF
Quarter CIF, video format with 176 x 144 pixels
Server Push
Subnet Mask
A continuous stream sent from the transmitter to the web browser
A mask that explains which part of an IP address is the network
address and which part composes the host address. It is usually
expressed in dotted-decimal notation (for example, 255.255.255.192).
TCP
UDP
URL
Transfer Control Protocol
User Datagram Protocol
Uniform Resource Locator
82
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
UTP
Unshielded Twisted Pair
WAN
See Wide Area Network
Wide Area Network
Multiple LANs connected together, usually over a great distance
C2900M-B (1/03)
83
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX A – CONNECTING PELCONET NET104A TO VARIOUS
COMPONENTS
TX+
TX
RX+
RX
DB9
-
-
TO RECEIVER
ESPRIT
RX+
RX
TX+
TX
-
-
SPECTRA
PIN
RS-232
RS-422/RS-485
1
2
3
4
5
6
7
8
9
DCD (DATA CARRIER DETECT)
RXD (RECEIVE DATA)
TXD (TRANSMIT DATA)
DTR (DATA TERMINAL READY)
GND (GROUND)
DSR (DATA SET READY)
RTS (READY TO SEND)
CTS (CLEAR TO SEND)
RXD- (RECEIVE DATA MINUS)
TXD- (TRANSMIT DATA MINUS)
1
2 3
4
5
GND
6
7
8
9
TXD+ (TRANSMIT DATA PLUS)
RXD+ (RECEIVE DATA PLUS)
Figure 38. DB9 Cable Wire Splicing
84
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PELCONET TO VARIOUS COMPONENTS WITH ASSORTED
KEYBOARDS
Connection Scenario 1
Refer to Figure 39 and the instructions that follow.
ᕥ
12 VAC
KBD300A
ᕧ
PELCONET RECEIVER
VIDEO OUT
DIRECT MODE
CAT 5
ᕤ
ᕢ
4
3
2
5
12 VDC
6
7
RD(A)
RD(B)
ᕡ
1
8
CONTROL
PORT
ᕣ
ᕦ
STRAIGHT CABLE
PV130
RS-232
ALARM I/O
PELCONET TRANSMITTER
POWER
P PROTOCOL ONLY
RX+ RX-
TX-
TX+
ᕨ
ETHERNET 10/100 BASE-T
RS-232/422/485
OUTPUTS
INPUTS
4800, 8, NONE, 1
ᕩ
AUDIO OUT
AUDIO IN
RECEIVER OR
SPECTRA
VIDEO 4
VIDEO 3
VIDEO 2
VIDEO 1
ᕫᕾ
Figure 39. KBD300A (Direct Mode) Connected to a Receiver or Spectra Dome System
C2900M-B (1/03)
85
Download from Www.Somanuals.com. All Manuals Search And Download.
ᕡ Connect a PV130 Converter to the RS-232 port on the front of the NET101R/R-A receiver. The
data format should be 4800 baud, 8 data bits, no parity, and 1 stop bit.
ᕢ Connect the black and white striped wire from the power supply that comes with the converter
to the converter’s +12 VDC terminal and the solid black wire to the GND terminal.
ᕣ Connect RD(A) on the converter to terminal 2 on the wall block. Connect RD(B) on the converter
to terminal 1 on the wall block.
ᕤ Connect a 12 VAC power supply to terminals 3 and 4 on the wall block.
ᕥ Set DIP switch 6 on the KBD300A to ON to enable turbo pan operation or OFF to disable that
feature. The KBD300A will recognize Direct Mode automatically.
ᕦ Connect the wall block to the KBD300A with an RJ-45 straight cable.
ᕧ Connect the monitor.
ᕨ Refer to Figures 38 and 39. Splice the supplied DB9 cable into the Spectra/Esprit or receiver
cable. Use P protocol only.
To connect multiple Spectras/Esprits or receivers to the transmitter, daisy chain them in a
series through the TX- and TX+ cable and attach the video cables to inputs 2 through 4.
ᕩ Plug the supplied DB9 cable into the COM port on the transmitter. The data format should be
4800 baud, 8 data bits, no parity, and 1 stop bit.
ᕫᕾ Connect the camera’s video to the transmitter.
86
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection Scenario 2
Refer to Figure 40 and the instructions that follow.
KBD4000
VIDEO
ON
ᕦ
OFF
12 VAC
PELCONET RECEIVER
ᕤ
4
3
2
5
6
7
VIDEO OUT
CAT 5
ᕢ
RD(A)
12 VDC
RD(B)
TD(A)
TD(B)
ᕥ
1
8
ᕡ
CONTROL
PORT
ᕣ
PV130
RS-232
STRAIGHT CABLE
ALARM I/O
9600, 8, ODD, 1
PELCONET TRANSMITTER
POWER
MULTIPLEXER
4
3
2
1
5
6
COM IN
Tx-
7
8
Tx+
Rx-
Rx+
ETHERNET 10/100 BASE-T
RS-232/422/485
ᕩ
STRAIGHT CABLE
ᕧ
OUTPUTS
9600, 8, ODD, 1
ᕨ
INPUTS
AUDIO OUT
AUDIO IN
VIDEO 4
VIDEO 3
ᕫᕾ
VIDEO 2
VIDEO 1
Figure 40. KBD4000 Connected to a Multiplexer
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
87
ᕡ Connect a PV130 Converter to the RS-232 port on the front of the NET101R/R-A receiver. The
data format must be 9600 baud, 8 data bits, odd parity, and 1 stop bit.
ᕢ Connect the black and white striped wire from the power supply that comes with the converter
to the converter’s +12 VDC terminal and the solid black wire to the GND terminal.
ᕣ Connect TD(A) on the converter to terminal 7 on the wall block. Connect TD(B) on the converter
to terminal 8 on the wall block. Connect RD(A) on the converter to terminal 2 on the wall block.
Connect RD(B) on the converter to terminal 1 on the wall block.
ᕤ Connect a 12 VAC power supply to terminals 3 and 4 on the wall block.
ᕥ Connect the wall block to the KBD4000 with an RJ-45 straight cable.
ᕦ Connect the monitor.
ᕧ Refer to Figures 38 and 40. Splice the supplied DB9 cable into the multiplexer wall block.
Connect TX- from the NET104A to terminal 2 on the wall block, TX+ to terminal 1, RX- to
terminal 7, and RX+ to terminal 8.
ᕨ Plug the supplied DB9 cable into the COM port on the transmitter. The data format must be
9600, 8, odd, 1.
ᕩ Connect the wall block to COM IN on the multiplexer with an RJ-45 straight cable.
ᕫᕾ Connect MAIN video output from the multiplexer to the transmitter.
88
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection Scenario 3
Refer to Figure 41 and the instructions that follow.
CM9750-UPS
CARD CAGE
KEYBOARD
ᕦ
PELCONET RECEIVER
VIDEO OUT
4
3
2
5
6
7
CAT 5
ᕣ
ᕢ
RD(A)
RD(B)
12 VDC
1
8
TD(A)
ᕡ
TD(B)
CONTROL
PORT
ᕤ
STRAIGHT CABLE
PV130
RS-232
ALARM I/O
ᕥ
4800, 8, EVEN, 1
COM IN
STRAIGHT CABLE
CM9760KBD
CM9760-CC1
SERCOM PORT
PROGRAMMED
FOR KBD
ᕫᕾ
PELCONET TRANSMITTER
FLIPPED CABLE
POWER
4
3
2
1
5
6
ᕢ
12VDC
ᕩ
TD(A)
TD(B)
RD(A)
RD(B)
7
8
ᕡ
ETHERNET 10/100 BASE-T
RS-232/422/485
ᕨ
PV130
OUTPUTS
INPUTS
4800,8, EVEN, 1
AUDIO OUT
AUDIO IN
VIDEO 4
VIDEO 3
VIDEO 2
VIDEO 1
Figure 41. CM9760KBD Connected to a CM9760-CC1 Controller
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
89
ᕡ Connect a PV130 Converter to the RS-232 port on the front of the NET101R/R-A receiver. The
data format must be 4800 baud, 8 data bits, even parity, and 1 stop bit.
ᕢ Connect the black and white striped wire from the power supply that comes with the converter
to the converter’s +12 VDC terminal and the solid black wire to the GND terminal.
ᕣ Connect TD(A) on the converter to terminal 7 on the wall block. Connect TD(B) on the converter
to terminal 8 on the wall block. Connect RD(A) on the converter to terminal 2 on the wall block.
Connect RD(B) on the converter to terminal 1 on the wall block.
ᕤ Connect an RJ-45 straight cable from the wall block to the supplied Pelco power pack.
ᕥ Connect an RJ-45 straight cable from the keyboard input connector on the power pack to COM
1 on the keyboard.
ᕦ Connect the monitor.
ᕧ Refer to Figures 38 and 41. Splice the supplied DB9 into the CM9760-CC1 wall block. Connect
TX- from the NET104A to terminal 2 on the wall block, TX+ to terminal 1, RX- to terminal 7, and
RX+ to terminal 8.
ᕨ Plug the supplied DB9 cable into the COM port on the transmitter. The data format must be
4800, 8, even, 1.
ᕩ Connect an RJ-45 flipped cable from the wall block to Sercom port 5 on the CC1’s rear panel.
ᕫᕾ Connect one of the three monitor outputs on the rear of the controller to the transmitter.
90
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PELCONET TO THE COM IN RS-232 PORT ON A GENEX
MULTIPLEXER
Refer to Figure 42 and the instructions that follow.
PELCONET TRANSMITTER
4
3
2
5
6
7
POWER
TX+
TX-
1
8
ᕦ
TO NETWORK
RX+
RX-
ᕢ
9600, 8, ODD, 1
ETHERNET 10/100 BASE-T
RS-232/422/485
DB9
STRAIGHT
CABLE
OUTPUTS
INPUTS
ᕤ
ᕡ
AUDIO OUT
AUDIO IN
VIDEO 4
VIDEO 3
PELCONET DB9
ADAPTER
GENEX COM IN
RJ-45 CONNECTOR
ᕥ
VIDEO 2
VIDEO 1
TX+
TX-
RX+
RX-
1
2
8
7
RX+
RX-
TX+
TX-
ᕣ
GENEX COM
8
1
8
1
IN
OUT
Figure 42. Connecting PelcoNet to Genex Using the COM IN RS-232 Port
ᕡ Verify that the multiplexer has Version 4.1 firmware. (The version number flashes on the
monitor when power is applied to the multiplexer.)
ᕢ Set the NET104A data port to Transparent, 9600 baud, 8 data bits, none (for parity), 1 stop
bit, RS-232, and half duplex mode off if it is not so set already.
ᕣ Create a cable using the above diagram.
ᕤ Attach the cable’s DB9 connector end to PelcoNet’s data port. Connect the cable’s RJ-45
connector end to COM OUT on the back of the multiplexer.
ᕥ Connect the MAIN video output from the multiplexer to the NET104A transmitter.
ᕦ Connect PelcoNet’s Ethernet port to the network using a Cat5 Ethernet patch cable.
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
91
CONNECTING A PELCONET RECEIVER TO A SYSTEM CM9502
Refer to Figure 43. This configuration lets an operator view and control cameras with a CM9505
keyboard.
CM9502-KBD
1200 BAUD, 8 BIT, 1 STOP BIT,
PELCONET RECEIVER
VIDEO OUT
NO PARITY
4
3
2
5
6
7
CAT 5
RD(A)
RD(B)
12 VDC
1
8
TD(A)
TD(B)
CONTROL
PORT
CM9505UPS
RS-232
TRANSPARENT
DATA
PV130
ALARM I/O
STRAIGHT
CABLE
CARD
CAGE
KBD
Figure 43. Using PelcoNet with CM9505 to Provide Remote Control
92
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PELCONET TO A CM9502 ASCII SERIAL PORT
Refer to Figures 38 and 44. This configuration lets an operator view and control cameras from a PC
using a web browser. (The operator’s PC is not shown on the diagram.)
8
7
1
2
6
5
3
4
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
93
CONNECTING PELCONET TO A CM6700 AND KBD200A FOR REMOTE
ASCII CONTROL
Refer to Pelco Tech Tip 00-3042 for an illustration (available on Pelco’s web site). This configuration
lets an operator view and control cameras with a remote KBD200A keyboard.
94
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PELCONET TO A CM6700 ASCII PORT
Refer to Figure 45. This configuration lets an operator view and control cameras from a PC using a
web browser. (The operator’s PC is not shown on the diagram.)
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
95
CONNECTING PELCONET TO A CM9760-DT FOR REMOTE BROWSER
CONTROL
Refer to Figure 46. This configuration lets an operator view and control cameras on a PC using a
web browser. (The operator’s PC is not shown on the diagram.)
96
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING PELCONET TO CM9760 EQUIPMENT FOR REMOTE
COMMUNICATION
Refer to Figures 38, 47, and 48. These configurations let an operator remotely view and control
cameras connected to the CM9760.
8
7
1
2
3
4
6
5
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
97
8
7
1
2
3
4
6
5
TD(A)
TD(B)
RD(A)
RD(B)
GND
+12 VDC
98
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING A PELCONET TRANSMITTER TO THE CM6800 ASCII PORT
Refer to Figure 49. This configuration lets an operator view and control cameras with a PC using a
web browser. (The operator’s PC is not shown on the diagram.) All settings are done in the CM6800
manager program or through a CM6800 menu. Note the following:
•
•
Port 2 defaults to ASCII and RS-232.
Ports 7 and 8 can be set to ASCII and RS-232 by using the CM6800 manager program (refer to
Figure 50) or by using a CM6800 menu (refer to Figure 51).
Pelco recommends using Port 2.
C2900M-B (1/03)
99
Download from Www.Somanuals.com. All Manuals Search And Download.
100
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 50. Manager Screen
SET SERIAL PORT 07
DEVICE:
TYPE:
BAUD RATE:
PARITY:
DATA BITS:
STOP BITS:
ASCII
RS232
9600
ODD
8
1
RETURN
Figure 51. Menu Screen
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
101
CONNECTING PELCONET TO A CM6800 AND KBD200A FOR REMOTE
ASCII CONTROL
Refer to Figure 52A and Figure 52B. This configuration lets an operator view and control cameras
with a remote KBD200A keyboard. All settings are done in the CM6800 manager program or
through a CM6800 menu. Note the following:
•
•
Port 2 defaults to ASCII and RS-232.
Ports 7 and 8 can be set to ASCII and RS-232 by using the CM6800 manager program (refer to
Figure 50) or by using a CM6800 menu (refer to Figure 51).
Pelco recommends using Port 2.
102
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
8
7
1
2
3
4
6
5
TD(A)
TD(B)
RD(A)
RD(B)
GND
+12 VDC
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
103
104
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX B – FREQUENTLY ASKED QUESTIONS (FAQs)
1. What Pelco devices can I control from my computer with the PelcoNet NET104A
Transmission System?
PelcoNet can control the following from Internet Explorer:
•
•
•
•
•
•
•
•
Spectra and Esprit
Genex multiplexer
CM9760 matrix (requires CM9760 data translator)
CM9740 matrix (requires CM9760 data translator)
CM9502 matrix (through integrated ASCII port)
CM8500 matrix (requires latest CM8500 data translator)
CM6700 matrix (through integrated ASCII port, COM 2)
CM6800 matrix
2. What TCP/IP ports does PelcoNet use?
PelcoNet lets you select which base port to use. The default is 25000. This means PelcoNet
will use TCP ports 25000-25001 and UDP ports 25002-25011 (12 ports total) for all video and
control data. The ports must be open for PelcoNet to function properly.
3. Can I view PelcoNet over the Internet?
Yes. You will need a static IP address and enough bandwidth to view live video. Pelco
recommends a minimum of 250 Kbps for medium image quality. Also check with your ISP to
verify the correct TCP and UDP ports are open through any routers or firewalls through which
you will connect. The base ports are adjustable in PelcoNet. For example, if you choose port
25000 (default), it will use TCP ports 25000-25001 and UDP ports 25002-25011 (12 ports total)
for all communication: video and control.
4. How many connections does PelcoNet support? Can more than one receiver connect
to a transmitter at the same time?
Yes. PelcoNet can support an unlimited number of receivers. To do so, all hubs, switches, and
routers must support multicasting (IGMP), and PelcoNet must be configured to use
multicasting. If the network hardware does not support this, then the maximum number of
simultaneous connections is five.
5. Can I enlarge the picture size in the browser?
Yes. You can select from two different image sizes in PelcoNet with the browser: 288 x 352 or
576 x 704.
6. What software does PelcoNet require?
PelcoNet works with Internet Explorer 5.5 or higher. An ActiveX plug-in is also required for
Internet Explorer to get live video. All software is included.
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
105
7. Can I control other manufacturers’ equipment from the browser?
Not at this time.
8. Can I record video with PelcoNet?
Yes. PelcoNet can record video to the hard drive of the viewing PC. The video is recorded in AVI
format, which allows playback through either the browser or Windows Media Player.
9. Everything is wired correctly but I do not have any control from the browser. What
else could be wrong?
The transparent data port settings must be set to match the equipment to which PelcoNet is
connected.
Also, in Internet Explorer, the Microsoft Virtual Machine must be enabled. To do so: on the
Tools menu, select Internet Options. Then select the Advanced tab. Locate the option Microsoft
VM. Place a check mark next to Java Console Enabled and JIT compiler for virtual machine
enabled. Reboot your computer.
These options are required for the Java applets in PelcoNet to function properly.
10. Can I control the Genex multiplexer from the browser and have a local KBD4000?
Yes. You must have Genex Version 4.1 or higher. This version lets you connect a KBD4000 to
the Genex COM IN port and PelcoNet to the Genex COM OUT. This gives you both local and
remote control. Refer to Connecting PelcoNet to the COM OUT RS-422 Port on a Genex
Multiplexer in Appendix A for detailed information.
11. Can I control the Genex multiplexer server?
Not at this time.
12. Can I use DHCP (dynamically assigned IP address) with PelcoNet?
Yes.
13. What type of compression does PelcoNet use?
PelcoNet uses the H.323 standard. H.323 is an industry standard for video teleconferencing
over the Internet. It provides the most effective use of bandwidth with excellent video quality.
14. I do not get live video in the browser but server push is working. What could be
wrong?
Verify that the ActiveX plug-in is installed and that your video is set to 16-bit color. Also check
with your network administrator to verify that the TCP/IP ports PelcoNet uses are not being
filtered and that you have enough bandwidth.
106
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
15. How do I program PelcoNet with HyperTerminal?
Using a null modem cable, connect a COM port on your PC to the COM port on NET104A. Open
HyperTerminal and set the port to use to 19200, 8, N, 1, and No Flow Control. Type ?, and
follow the help menu.
16. How much bandwidth does PelcoNet use?
PelcoNet’s bandwidth is adjustable. You can set it from 10 Kbps up to 1 Mbps. Pelco
recommends a minimum of 250 Kbps for live video at medium image quality. Check with your
network administrator for how much bandwidth to use.
17. Can I use PelcoNet with a DSL or cable connection?
Yes. You will need a static IP address from your provider. Also verify what kind of bandwidth
you will get since it varies by location. Verify that your provider is not filtering the TCP/IP ports
that PelcoNet uses.
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
107
INDEX
Symbols
D
Data bits 61
Date (system) 43
Default address 19
10BASE-T 17, 34
A
Defaults button (motion detection) 56
DHCP 47
Disconnect 23
Disconnect commands 35
Display MAC address command 35
Display version information command 35
Door entry system 58
ActiveX 50, 62
ActiveX control file 38
Alarm connect 58
Alarm indicator 56
Alarm input active high/low 57
Alarm input pins 57
Alarm IP address 58, 70
Alarm IP set command 35
Alarm settings configuration page 54
Alarm status 57
Audio coding mode 53
Audio input level 53
E
Email alarm notification 71
Email notification 58
Enable multicast streaming 47
Enable multilink h.323 47
Esprit live video/server push page contents
69
Audio line in/out 30
Audio output level 53
Audio settings configuration page 52
Average n[frames] 56
F
B
Firmware update 44
Firmware upload 73
Flash EPROM 73
Base port 47
Baud rate 61
FTP server IP address 51
Full duplex audio 23, 58
Bistable mode 59
Buttons for recording/playback 71
G
C
G.711/G.728 audio compression standards 53
Gateway IP address 23, 46
Camera follows alarm input 57
Camera names 50
Gateway IP address set command 35
General settings configuration page 42
Genex live video/server push page contents
66
Coding mode 53
Com ports 61
Command reference 36
Common Intermediate Format (CIF) 49
Configuration download 44
Configuration pages 38
alarm settings 54
H
Halfduplex mode 61
audio settings 52
general settings 42
interface settings 60
network settings 46
Hardware version number 44
Hardware-to-hardware 22
Help menu command 35
HTTP server 38
video settings 48
Configuration upload 44
Connect (to IP address) 58
Connect to alarm IP command 35
Country specific adapters 79
108
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
I
O
Idle state 59
Input level 53
Object min size [n*n blocks] 56
Operate relay 59
Interface settings configuration page 60
Internet 38, 40
IP address 11
Output level 53
P
IP address set command 35
IP address setting 46
Parity 61
Password (field) 43
Password (server field) 51
Password level 43
Password setting 43
Path 51
J
JPEG 58, 71
JPEG file name 51
JPEG size 51
Patterns 64
Pelco Internet home page 38
Playback buttons 71
Playing the recording 72
Presets 64
Programming menus 64
PTZ cameras 12
L
Live video auto connect 58
Live video receive IP 58
Local sensitivity 56
Login name 51
Q
M
QCIF (Quarter Common Intermediate Format)
49
Mail reply address 47
Mail server IP address 47
Master alarm input pin 57
Matrix Control live video/server push page
content 65
R
Real-time clock 42
Menu tree 39
Microsoft Internet Explorer 38
Monostable 59
Receiver email address 59
Recording buttons 71
Recording the display 72
Relay (operate) 59
Motion alarm 55
Motion detection 55, 70
Motion tracking 55
Relay follows 59
Relay idle state 59
Motion-JPEG 20
Relay names 59
Multicast group IP 47
Multicast video port 47
Remote password 58
RS-232 interface flow control mechanism 23
RS-232/485 61
N
RS-485 converter support 61
Network administrator instructions 9
Network interface bandwidth 50
Network settings configuration page 46
Non-volatile memory 41
C2900M-B (1/03)
109
Download from Www.Somanuals.com. All Manuals Search And Download.
S
Select area 55
Send email 58
Sensitivity of motion detection 70
Server Push 20
Set button 41
SMTP server 47
Software version number 44
Spectra live video/server push page contents
68
Status of alarm inputs 71
Stop bits 61
Subnet mask 46
Subnet mask set command 35
T
Terminal program commands 34
Time (system) 43
Time server IP 44
Time slice 51
Time stamping 51
Time to live (multicast) 47
Time zone 43
Timeout for email messages 71
Tracker box 55
Transmission rate 50
Trigger relay 59
U
Unit ID 43
Unit name 43
V
Version numbers for hardware/software 42
Video alarm 55
Video bandwidth ActiveX 50
Video priority 50
Video quality 49
Video resolution 49
Video settings configuration page 48
Video standard 30, 49
W
Web browser 10, 23, 38
110
C2900M-B (1/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of
shipment. Exceptions to this warranty are as noted below:
•
•
•
•
•
•
•
•
•
•
Five years on Pelco manufactured cameras (CC3500/CC3600/CC3700 and MC3500/MC3600 Series); two years on all other cameras.
Three years on Genex® Series (multiplexers, server, and keyboard) and 090 Series Camclosure® Camera System.
Two years on 100/150, 200 and 300 Series Camclosure® Camera Systems.
Two years on all standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM8500/CM9500/CM9740/CM9760 Matrix, DF5 and DF8 Series Fixed Dome products.
Two years on Spectra®, Esprit®, and PS20 Scanners, including when used in continuous motion applications.
Two years on Esprit and WW5700 series window wiper (excluding wiper blades).
Eighteen months on DX Series digital video recorders.
One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under
this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to
the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or
consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from
state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and
provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an
authorization number (CA number if returned for credit, and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the
appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico:
If you are located outside the continental U.S., Alaska, Hawaii or
Puerto Rico:
Service Department
Pelco
3500 Pelco Way
Intermediate Consignee
American Overseas Air Freight
320 Beach Road
Ultimate Consignee
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
USA
Clovis, CA 93612-5699
Burlingame, CA 94010
USA
® Pelco, the Pelco logo, Spectra, Genex, Legacy, Esprit, and Camclosure are registered trademarks of Pelco.
® Windows is a registered trademark of Microsoft Corporation.
© Copyright 2002, Pelco. All rights reserved.
REVISION HISTORY
Manual #
C2900M
Date
8/02
Comments
Original version.
C2900M-A
10/02
Revised Figure 13. Added notes about the View button and about viewing and controlling cameras
on the spot and main monitors to the Genex Live Video/Server Push Page Contents section. Added
note about the camera buttons to Spectra Live Video/Server Push Page Contents section. Added
material about the reboot link on the Video Settings page.
Revised Figures 38 and 42.
C2900M-B
1/03
C2900M-B (1/03)
111
Download from Www.Somanuals.com. All Manuals Search And Download.
®
World Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
www.pelco.com
ISO9001
Orangeburg, New York Las Vegas, Nevada Eindhoven, The Netherlands Wokingham, United Kingdom Montreal, Canada
Download from Www.Somanuals.com. All Manuals Search And Download.
|