Installation and Assembly:
Full Service Video Wall Mount
Model: DS-VW760
COLLAPSED
EXTENDED
Maximum Load Capacity: 150 Ib ( 68 kg)
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
1 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Vertical Spacing Location
If DS-VWS0## Wall Plate Spacer Kit is not available use diagram below to determine vertical spacing.
To determine lower mounting slot position of second mount, add display height to (Y1) or (Y2)
DISPLAY
HEIGHT
10.25
1.688
.938
X
Y2
Y1
Vertical Location
X - 10.25 + (.938 OR 1.688) = (Y1 OR Y2)
Horizontal Spacing Location
If DS-VWS0## Wall Plate Spacer Kit is not available use diagram below to determine horizontal spacing.
To determine edge of second mount, add (Z) to edge or first mount.
DISPLAYWIDTH
16.00"
20.00"
24.00"
Z
17.50"
Horizontal Location
DISPLAY WIDTH - (35) = Z (SPACING BETWEEN MOUNTS)
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
3 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
A
B
C
Parts List
Description
Qty.
1
2
2
2
4
4
4
4
4
4
1
2
Part #
145‐1104
145‐1105
145‐1091
520‐1164
5S1‐015‐C03
590‐0320
540‐1008
590‐2233
520‐1128
520‐9257
560‐9646
560‐9711
600‐1014
A
B
C
D
E
F
G
H
I
pull out mount assembly
adapter bracket
lock bracket
M5 x 10 mm socket pin type‐F screw
#14 x 2.5" hex head wood screw
concrete anchor
fender washer
nylon shoulder washer
M6 x 12 mm phillips screw
M8 x 15 mm phillips screw
4 mm allen wrench
cable tie (not shown)
J
K
L
M mesh sleeve (not shown)
1
D
H
E
F
G
I
J
K
Open video wall mount assembly by releasing locking tab. Pull or push up
on locking tab.
PULL UP
1
LOCKING TAB
VIDEO WALL
MOUNT ASSEMBL
Y
PUSH UP
LOCKING TAB
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
4 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing Display Carriage
Remove display carriage by removing clip, pull release pin, and screws as shown. Remove screws using
4 mm allen wrench (K).
2
CLIP
DISPLAY CARRIAGE
SCREWS
VIDEO WALL
MOUNT ASSEMBL
Y
RELEASE PIN
VIDEO WALL
MOUNT ASSEMBL
DISPLAY CARRIAGE
Y
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
5 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation to Wall Stud
WARNING
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder
is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-
ers are responsible to provide hardware for other types of mounting situations.
Use a stud finder to locate the edges of the stud. Use of an edge-to-edge stud finder is highly recommended.
Based on their edges, draw a vertical line down the stud center. Place video wall mount assembly on wall as a
template. Level plate, and mark the center of the four mounting holes. Make sure that the mounting holes are on
the stud centerline. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Make sure that the video wall mount
assembly is level, secure it using four #14 x 2.5" wood screws (E) and fender washers (G) as shown below.
3
VIDEO WALL
MOUNT ASSEMBL
Y
G
E
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
6 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation to Solid Concrete or Cinder Block
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount
in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM
C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware
and components.
solid concrete
Make sure that video wall mount assembly is level,
1
use it as a template to mark four mounting holes.
Drill four 1/4” (6 mm) dia. holes to a minimum depth
F
cinder block
of 2.5” (64 mm). Insert anchors (F) in holes flush
with wall as shown (right). Place video wall mount
assembly over anchors and secure with four #14
x 2.5” screws (E), and fender washers (G). Level,
then tighten all fasteners.
WARNING
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
VIDEO WALL
MOUNT ASSEMBL
Y
G
E
• Never tighten in excess of 80 in. • lb (9 N.M.).
concrete
surface
• Always attach concrete expansion anchors directly
to load-bearing concrete.
1
• Never attach concrete expansion anchors to
concrete covered with plaster, drywall, or other
finishing material. If mounting to concrete surfaces
covered with a finishing surface is unavoidable,
the finishing surface must be counterbored as
shown below. Be sure concrete anchors do not
pull away from concrete when tightening screws. If
plaster/drywall is thicker than 5/8" (16 mm), custom
fasteners must be supplied by installer
F
Drill holes and insert anchors (F).
A
2
E
F
Place plate (A) over anchors (E) and secure with screws (F).
INCORRECT
CORRECT
3
concrete
concrete
wall
plate
wall
plate
plaster/
drywall
plaster/
drywall
Tighten all fasteners.
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
7 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Re-Attaching Display Carriage
Secure display carriage by pulling release pin, fastening clevis pin, clip, four screws, and spacer as shown.
NOTE: make sure that spacer is in-between display carriage and video wall mount assembly.
4
SPACER
CLIP
CLEVIS PIN
DISPLAY CARRIAGE
HOLE IN PIN
SCREWS
VIDEO WALL
MOUNT ASSEMBL
Y
RELEASE PIN
Attaching Adapter Brackets to Display
Attach adapter brackets (B) to back of display using four M6 x 12 mm phillips screws (I) with nylon shoulder washer (H), or four
M8 x 15 mm phillips screws (J) as shown below.
NOTE: Hardware to attach dedicated plates to the mount are included with the dedicated plates.
5
DISPLAY
H
I or J
MAX VESA-600 mm
MIN VESA-200 mm
B
400 mm
300 mm
200 mm
PLP
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
8 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Attaching Adapter Brackets to Display Carriage
Attach adapter brackets (B) to display carriage. Slide adapter brackets (B) to position based on hole pattern as shown below.
Loosely fasten in place using security screw as shown in detail 1.
NOTE: Once display is located in desired position, tighten security screws using 4mm allen wrench (K) to lock in place.
6
DISPLAY CARRIAGE
DETAIL 1
B
B
B
SECURITY SCREW
Horizontal Display Position
Screen and adapter brackets can slide along rail to position
.
screen horizontally
OF
OUTSIDE EDGE
OPTIONAL GUIDE: When positioning adapter brackets make sure outside edge
of adapter bracket is in notch on display carriage as shown in detail 2.
ADAPTER BRACKET
NOTCH
600 mm
400 mm
300 mm
200 mm
B
PLP
DISPLAY CARRIAGE
DETAIL 2
FRONT
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
9 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Carriage Adjustment
Use legend below to determine position of display.
NOTE: Each knob can be adjusted independently for fine tuning adjustments.
7
Turn knob CLOCKWISE to tighten
Turn knob COUNTER-CLOCKWISE to loosen
UP
DOWN
ROTATE LEFT
ROTATE RIGHT
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
10 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Adapter Bracket Adjustment
Use legend below to determine position of display.
NOTE: Each knob can be adjusted independently for fine tuning adjustments.
8
Turn knob CLOCKWISE to tighten
Turn knob COUNTER-CLOCKWISE to loosen
OUT
BACK
IN
TILT FORWARD
BACK
BACK
TILT BACKWARD TILT RIGHT
TILT LEFT
BACK
BACK
BACK
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
11 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Management
Display cables can be routed through top or bottom of video wall mount assembly.
NOTE: Use mesh sleeve (M) and cable ties (L) for cable management as shown in detail 3
NOTE: Cable ties and cable management slots on video wall mount assembly can be used to secure display cables.
9
H TOP
CABLE THROUG
S
DISPLAY CABLE
VIDEO WALL
BLY
MOUNT ASSEM
M
L
DETAIL 3
DISPLAY
CABLE MANAGEMENT
SLOTS
H BOTTOM
CABLE THROUG
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
12 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Open and Close Display Carriage
Open display carriage by releasing locking pin. Once open push down on access bracket to lock display carriage in place.
NOTE: Make sure that access bracket is notch in display carriage as shown in detail 4.
10
ACCESS BRACKETS
SLOT
NOTCH
DETAIL 4
VIDEO WALL
MOUNT ASSEMBL
DISPLAY CARRIAGE
Y
LOCKING PIN
Close Display Carriage
Close display carriage by pulling up on access bracket to unlock display carriage. Once unlocked close display carriage.
NOTE: Make sure that access bracket is out of notch in display carriage before closing.
VIDEO WALL
MOUNT ASSEMBL
DISPLAY CARRIAGE
Y
SLOT
NOTCH
ACCESS BRACKETS
13 of 14
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Secure locking tab using two socket pin screws (D) as shown below.
Lock bracket (C) and lock (not supplied) can be used to secure display carriage to video wall mount assembly as
shown in below.
11
Optional
C
ALL
SLOT IN VIDEO W
Y
MOUNT ASSEMBL
D
VIDEO WALL
MOUNT ASSEMBL
Y
C
LOCK
(NOT SUPPLIED)
LOCKING TAB
ISSUED: 04-23-10 SHEET #: 145-9010-2 04-27-10
14 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
|