Pioneer Home Theater System AS LX70 User Manual

Operating Instructions |  
SX-LX70W  
SSP-LX70ST  
AS-LX70  
HTP-LX  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VENTILATION CAUTION  
CAUTION  
When installing this unit, make sure to leave space  
around the unit for ventilation to improve heat  
radiation (at least 10 cm at top, 10 cm at rear, and  
10 cm at each side).  
The STANDBY/ON switch on this unit will not  
completely shut off all power from the AC outlet.  
Since the power cord serves as the main disconnect  
device for the unit, you will need to unplug it from  
the AC outlet to shut down all power. Therefore,  
make sure the unit has been installed so that the  
power cord can be easily unplugged from the AC  
outlet in case of an accident. To avoid fire hazard,  
the power cord should also be unplugged from the  
AC outlet when left unused for a long period of time  
WARNING  
Slots and openings in the cabinet are provided for  
ventilation to ensure reliable operation of the  
product, and to protect it from overheating. To  
prevent fire hazard, the openings should never be  
blocked or covered with items (such as newspapers,  
table-cloths, curtains) or by operating the  
(for example, when on vacation).  
D3-4-2-2-2a_A_En  
equipment on thick carpet or a bed.  
D3-4-2-1-7b_A_En  
WARNING  
WARNING  
Before plugging in for the first time, read the following  
section carefully.  
To prevent injury, the receiver subwoofer must be  
securely attached to the floor in accordance with this  
operating instructions.  
The voltage of the available power supply differs  
according to country or region. Be sure that the  
power supply voltage of the area where this unit  
will be used meets the required voltage (e.g., 230 V  
or 120 V) written on the rear panel.  
D3-4-2-1-4_A_En  
This product is for general household purposes. Any  
failure due to use for other than household purposes  
(such as long-term use for business purposes in a  
restaurant or use in a car or ship) and which  
requires repair will be charged for even during the  
warranty period.  
K041_En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Contents  
What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
05 Listening to your system  
Effective Sound (for optimum sound) . . . . . . . . . . . . 24  
Auto listening mode . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Listening in surround sound. . . . . . . . . . . . . . . . . . . 24  
Dolby Pro Logic II Music settings . . . . . . . . . . . . . . 25  
Center image setting . . . . . . . . . . . . . . . . . . . . . . . 25  
Using Advanced Surround . . . . . . . . . . . . . . . . . . . . 25  
Using Front Stage Surround Advance . . . . . . . . . . . 26  
Listening in stereo . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Genre Sync Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Using the Sound Retriever . . . . . . . . . . . . . . . . . . . . 26  
Listening with MCACC Effect . . . . . . . . . . . . . . . . . . 27  
Using Midnight, Loudness and  
01 Speaker Setup Guide  
Safety precautions when setting up . . . . . . . . . . . . . . 6  
Home theater sound setup . . . . . . . . . . . . . . . . . . . . . 6  
Standard surround setup . . . . . . . . . . . . . . . . . . . . . 6  
Front surround setup . . . . . . . . . . . . . . . . . . . . . . . . 6  
Preparing the speakers. . . . . . . . . . . . . . . . . . . . . . . . 6  
Using the supplied speaker bases . . . . . . . . . . . . . . 6  
When not using the supplied speaker bases . . . . . . 7  
Connect the speaker system. . . . . . . . . . . . . . . . . . . . 7  
Additional notes on speaker placement . . . . . . . . . . . 7  
02 Connecting up  
Quiet listening modes . . . . . . . . . . . . . . . . . . . . . . . 27  
Adjusting the bass and treble. . . . . . . . . . . . . . . . . . 27  
Adjusting sound delay . . . . . . . . . . . . . . . . . . . . . . . 27  
Receiver subwoofer . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Side panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Rear panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Back of display unit . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Basic connections . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
06 Listening to the radio  
Listening to the radio . . . . . . . . . . . . . . . . . . . . . . . . 28  
Improving poor FM reception . . . . . . . . . . . . . . . . . 28  
Improving poor AM sound . . . . . . . . . . . . . . . . . . . 28  
Changing the noise cut mode . . . . . . . . . . . . . . . . 28  
Memorizing stations. . . . . . . . . . . . . . . . . . . . . . . . 29  
Listening to station presets . . . . . . . . . . . . . . . . . . 29  
Changing the frequency step . . . . . . . . . . . . . . . . . 29  
03 Controls and displays  
Display unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Operating the receiver subwoofer . . . . . . . . . . . . . 15  
Operating the built-in FM/AM tuner . . . . . . . . . . . . 16  
Operating Pioneer plasma televisions and TVs. . . . 17  
Operating a Pioneer Blu-ray Disc player. . . . . . . . . 18  
Operating a Pioneer DVD player. . . . . . . . . . . . . . . 19  
Operating a Pioneer HDD/DVD Recorder. . . . . . . . 20  
Putting the batteries in the remote control . . . . . . . . 21  
Using the remote control . . . . . . . . . . . . . . . . . . . . . 22  
Operating the remote control . . . . . . . . . . . . . . . . . . 22  
Using the LCD touch screen . . . . . . . . . . . . . . . . . 22  
07 Surround sound settings  
Using the Sound Setup menu. . . . . . . . . . . . . . . . . . 30  
Channel level setting . . . . . . . . . . . . . . . . . . . . . . . 30  
Speaker distance setting1 . . . . . . . . . . . . . . . . . . . 30  
Dynamic Range Control . . . . . . . . . . . . . . . . . . . . . 31  
Dual mono setting . . . . . . . . . . . . . . . . . . . . . . . . . 31  
Using the Virtual Surround Back mode . . . . . . . . . 32  
LFE Attenuate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
Adjusting the channel levels using the test tone. . . . 32  
04 Getting started  
Using the Auto MCACC setup  
for optimal surround sound . . . . . . . . . . . . . . . . . . . 23  
08 Other connections  
Connecting auxiliary components . . . . . . . . . . . . . . 33  
Connecting for digital audio. . . . . . . . . . . . . . . . . . 33  
Connecting an analog audio component . . . . . . . . 33  
Connecting an iPod . . . . . . . . . . . . . . . . . . . . . . . . 34  
Listening to an external audio source . . . . . . . . . . . . 34  
Connecting external antennas . . . . . . . . . . . . . . . . . 35  
About control out connections . . . . . . . . . . . . . . . . . 35  
Connecting using HDMI. . . . . . . . . . . . . . . . . . . . . . 35  
HDMI mode setting . . . . . . . . . . . . . . . . . . . . . . . . 36  
About HDMI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
4
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
09 HDMI Control  
10 Additional information  
Making the HDMI Control connections . . . . . . . . . . 37  
Setting the HDMI options . . . . . . . . . . . . . . . . . . . . 38  
Setting the HDMI Control mode . . . . . . . . . . . . . . 38  
Setting the Auto Delay. . . . . . . . . . . . . . . . . . . . . . 39  
Audio input settings from plasma televisions  
(TV Input). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
Before using synchronization . . . . . . . . . . . . . . . . . 39  
Synchronized amp mode . . . . . . . . . . . . . . . . . . . . . 39  
Synchronized amp mode operations . . . . . . . . . . . 39  
Canceling synchronized amp mode. . . . . . . . . . . . 39  
Dimming the display . . . . . . . . . . . . . . . . . . . . . . . . 40  
Setting the sleep timer. . . . . . . . . . . . . . . . . . . . . . . 40  
Setting up the remote to control your TV . . . . . . . . . 40  
TV Preset code list . . . . . . . . . . . . . . . . . . . . . . . . . . 41  
Resetting the system . . . . . . . . . . . . . . . . . . . . . . . . 42  
Installation and maintenance . . . . . . . . . . . . . . . . . 42  
Hints on installation . . . . . . . . . . . . . . . . . . . . . . . 42  
Surround sound formats . . . . . . . . . . . . . . . . . . . . . 42  
Dolby. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
DTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
Tuner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
Displayed Messages . . . . . . . . . . . . . . . . . . . . . . . 46  
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
What’s in the box  
Please confirm that the following items are all supplied.  
Accessory box (AS-LX70):  
Receiver subwoofer (SX-LX70W) box:  
• Remote control (page 15)  
• Cleaning cloth  
• AA/LR6 alkaline batteries x4 (page 21)  
• Power cords x3 (page 12)  
• Display unit (page 13)  
Speakers (SSP-LX70ST) box:  
• Speakers (front/center x2, surround x2) (page 6, 11)  
• Speaker cables x6 (page 11)  
• Speaker bases x4 (page 6)  
• Non-skid pads x16 (page 6, 7)  
• Screws x4 (page 7)  
• AM loop antenna (page 11)  
• FM wire antenna (page 11)  
• Microphone (for Auto MCACC setup) (page 23)  
• HDMI cable  
• Control cable (page 35)  
• Display cable (page 11)  
• Optical digital cable (page 12)  
• iPod cable (page 34)  
• This operating instructions  
5
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Speaker Setup Guide  
01  
CShpapetera1ker Setup Guide  
Front surround setup  
This setup is ideal when rear surround speaker  
placement isn’t possible or you want to avoid running  
long speaker cables in your listening area. Use this setup  
together with the Front Stage Surround Advance modes  
in page 26.  
Safety precautions when setting up  
When assembling the speakers, lay them down flat on  
their side to avoid accidents or injury. Make sure to use a  
stable surface when assembling, setting up, and placing  
the speakers.  
Surround (L)  
Surround (R)  
Front/center (R)  
Front/center (L)  
Home theater sound setup  
Depending on the size and characteristics of your room,  
you can place your speakers in one of two ways using this  
system.  
Receiver  
subwoofer  
Standard surround setup  
This is a standard multichannel surround sound speaker  
setup for optimal 5.1 channel home theater sound.  
Listening position  
Front/center (L)  
Front/center (R)  
Preparing the speakers  
This unit comes with speaker bases that can be used to  
adjust the speakers to the design of the room in which  
they are placed.  
Receiver  
subwoofer  
Listening position  
Using the supplied speaker bases  
1
Attach the non-skid pads to the speaker bases, as  
shown below.  
Surround (L)  
Surround (R)  
Use the adhesive side of the pads to attach them to the  
base of each speaker base.  
Non-skid pads x 16  
Each speaker base  
6
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Speaker Setup Guide  
01  
2
Attach the speaker bases.  
Place the speaker atop a supplied speaker base, and fix  
the base in place by using one of the supplied screws.  
Connect the speaker system  
Refer to Connecting up to connect the speakers properly.  
After connecting everything, place the speakers as  
shown in the diagram above for optimal surround sound.  
After placing the speakers, run the Auto MCACC setup  
(page 23) to complete your surround sound setup.  
• The supplied speaker bases come in two different  
shapes. You can determine the correct base for a  
speaker by checking if the screw’s location lines up  
correctly when the speaker is placed atop the base.  
(There are specific bases for the front/center (L) and  
surround speaker (R), and for the front/center (R) and  
surround speaker (L), with two of each type included.)  
Additional notes on speaker placement  
• Install the main front left and right speakers at an  
equal distance from the TV.  
Speaker  
• When using the Standard surround setup, install the  
surround speakers slightly above ear level for  
optimum effect.  
Screw  
• When using the Front surround setup, separate the  
left and right speakers by about 1.5 m for optimum  
effect.  
Speaker base  
Precautions:  
• Do not place the speaker on an unstable surface, as  
doing so may cause the speaker to fall and cause  
damage or bodily injury.  
When not using the supplied speaker bases  
Attach the non-skid pads to the base of each of  
• All speakers supplied with this system are  
magnetically shielded. However, depending on the  
installation location, color distortion may occur if a  
speaker is installed extremely close to the screen of a  
television set. If this happens, turn the power switch  
of the television set OFF, and turn it ON after 15 min  
to 30 min. If the problem persists, place the speaker  
system away from the television set.  
the front/center and surround speakers (as shown).  
Use the adhesive side of the pads to attach them to the  
base of each speaker.  
• For safety, make sure that there is no exposed bare  
speaker wire outside of the speaker terminals.  
• Do not connect the supplied speakers with any other  
amplifier. This may result in malfunction or fire.  
Non-skid pads x 16  
Front/center and surround speakers  
• Do not connect any speakers other than those  
supplied to this system.  
• The speaker system grill cannot be removed. Do not  
try to forcibly remove it since doing so may damage  
the grille.  
• When cleaning the cabinet, use the provided  
cleaning cloth.  
Do not allow alcohol, thinner, benzene, or  
insecticides to come into contact with the surface,  
since finish discoloration may occur.  
Also, when using chemically impregnated cleaning  
cloths, follow their precautions carefully.  
7
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting up  
02  
CChoaptnern2 ecting up  
Receiver subwoofer  
Side panel  
ANTENNA  
AM LOOP  
L
R
R
L
L
R
L
OUT  
1
OUT  
2
IN  
1
IN  
2
R
AC IN  
FRONT  
CENTER  
FRONT  
SURROUND  
SUBWOOFER  
CONTROL  
OPTICAL  
DIGITAL  
FM  
(
)
SPEAKERS 8 Ω  
UNBAL 75  
ANALOG  
AUDIO IN  
1
2
3
4
5
6
7
• There is a cover over the connectors on the side  
panel.  
A. When making connections, lift the two hooks and  
remove the cover.  
B. Once connections are finished, line up the three  
positions and place the cover back in its original  
position.  
1
CONTROL OUT jacks (x2)  
Connect other Pioneer components with the supplied  
control cable  
.
2
DIGITAL OPTICAL IN jacks (x2)  
To listen to optical digital audio, change the input to  
Digital 1 or Digital 2.  
When the digital output jacks of your TV are connected to  
these jacks, set ‘TV Input’ (see page 39).  
B
3
4
5
AM LOOP antenna terminal  
FM antenna socket  
ANALOG AUDIO IN jacks  
Handle sound from an external component by using  
stereo audio code. To listen to analog audio, change the  
input to Analog.  
A
When the analog output jacks of your TV are connected  
to these jacks, set ‘TV Input’ (see page 39).  
6
SPEAKERS terminals  
Match the colors of the speaker cords to their respective  
connectors.  
7
AC IN – Power inlet  
8
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting up  
02  
Rear panel  
8
HDMI OUT connector  
Connect to a television that has an HDMI terminal.  
9
HDMI IN connectors (x3)  
HDMI  
OUT  
IN  
3
IN  
2
IN  
1
Use high-quality audio/video connection with compatible  
HDMI devices.  
To select this input, choose HDMI 1 to HDMI 3.  
SYSTEM  
10 SYSTEM connector  
Connect to the display unit.  
HDMI  
OUT  
IN 3  
IN 2  
IN 1  
SYSTEM  
8
9
10  
Back of display unit  
1
SYSTEM connector  
Connect to the receiver subwoofer.  
DISPLAY UNIT  
2
F.AUDIO input  
iPod  
MCACC  
SYSTEM  
F.AUDIO  
SETUP MIC  
To listen to audio from an external component, connect  
with a stereo mini-plug cable. Once connected, the input  
automatically changes to Front Audio In.  
3
iPod input terminal  
1
2
3
4
Use to connect your Apple iPod as an audio source.  
When you connect an iPod, the input automatically  
changes to iPod.  
4
MCACC SETUP MIC jack  
Use to connect the supplied microphone for the Auto  
MCACC setup (see page 23).  
9
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting up  
02  
Basic connections  
Receiver subwoofer  
Display unit  
HDMI  
OUT  
IN  
3
IN  
2
IN  
1
DISPLAY UNIT  
iPod  
MCACC  
SETUP MIC  
SYSTEM  
F.AUDIO  
SYSTEM  
INPUT  
Rear panel  
Side panel  
ANTENNA  
1
L
AM LOOP  
R
R
L
L
R
L
SYSTEM  
R
FRONT  
CENTER  
FRONT  
SURROUND  
SUB  
Display cable  
ANALOG  
AUDIO IN  
4
2
3
CL  
FL  
FR  
CR  
AM loop antenna  
FM antenna  
Front/center  
speaker (R)  
Front/center  
speaker (L)  
Listening position  
Surround  
speaker (R)  
Surround  
speaker (L)  
SL  
SR  
Important  
WARNING  
• When connecting this system or changing  
connections, be sure to switch power off and  
disconnect the power cord from the wall socket.  
After completing all connections, connect the power  
cords to the wall socket.  
• Pioneer bears no responsibility for accidents  
resulting from faulty assembly or installation,  
insufficient mounting strength of walls, mounting  
fixtures (or other building fixtures), misuse or natural  
disasters.  
10  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting up  
02  
1
Connect the display unit to the receiver subwoofer.  
4
Connect each speaker.  
Plug the display cable into the connector on the rear of  
the display unit, then plug the other end of the display  
cable into SYSTEM connector on the receiver subwoofer.  
• Each speaker cable has a color-coded connector at  
one end and two wires at the other end.  
Color-coded wire  
(Connect to speaker)  
Caution  
Color-coded connector  
(Connect to receiver subwoofer)  
• Do not attempt to attach the display unit to the wall.  
2
Assemble the AM loop antenna.  
• Twist and pull off the protective shields on each wire.  
a
b
c
• Connect the wires to the speaker. Each speaker in the  
illustration can be identified by means of the color-  
coded indicator provided on the rear-surface model  
label. Match the color-coded wire with the color  
indicator on the model label, then insert the color-  
coded wire into the red (+) side and the other wire  
into the black () side.  
a. Bend the stand in the direction indicated by the arrow.  
b. Clip the loop onto the stand.  
c. If you want to fix to a wall or other surface, perform  
step b after first securing the stand with screws.  
It is recommended that you determine the reception  
strength before securing the stand with the screws.  
Black (–) Red (+)  
Color-coded wire  
1
3
Connect the AM and FM antennas .  
a. Connect one wire of the AM loop antenna to each AM  
2
antenna terminal .  
For each terminal, press down on the tab to open;  
insert the wire, then release to secure.  
2
3
1
• Connect the other end to the color-coded speaker  
terminals on the side of the receiver subwoofer. Make  
sure to insert completely.  
Be careful when inserting the speaker plug, as it  
must be inserted in the proper direction when being  
plugged into one of the terminals. Please make sure  
to connect correctly.  
3
b. Push the FM antenna plug onto the center pin of the  
FM antenna socket.  
Note  
1 • Keep antenna cables away from other cables, the display unit and receiver subwoofer.  
• If reception with the supplied antenna is poor, see Improving poor FM reception and Improving poor AM sound on page 28 or Connecting  
external antennas on page 35.  
• Do not attach any antenna other than the provided loop antenna, or an external antenna as described on page 35.  
2 • Don’t let it come into contact with metal objects and avoid placing near computers, television sets or other electrical appliances.  
• If radio reception is poor, you may be able improve it by re-inserting each antenna wire into the opposite terminal.  
• For best reception, do not untwist the AM loop antenna wires or wrap them around the loop antenna.  
3 To ensure optimum reception, make sure the FM antenna is fully extended and not coiled or hanging at the rear of the unit.  
11  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Connecting up  
02  
Rear panel  
Side panel  
HDMI  
OUT  
IN 3  
IN 2  
IN 1  
ANTENNA  
AM LOOP  
L
IN  
1
IN  
2
R
OPTICAL  
DIGITAL  
ANALOG  
AUDIO IN  
SYSTEM  
Receiver subwoofer  
or  
6
7
From digital audio  
output (optical)  
From Audio output  
To HDMI input  
TV  
Connect the receiver subwoofer to your TV.  
• Connect the HDMI OUT jack on receiver subwoofer  
to an HDMI input on your TV.  
6
7
Caution  
• These speaker terminals carry HAZARDOUS LIVE  
voltage. To prevent the risk of electric shock when  
connecting or disconnecting the speaker cables,  
disconnect the power cord before touching any  
uninsulated parts.  
Connect an audio cable from your TV to the  
receiver subwoofer.  
• To listen to TV audio on this unit, you must connect  
the TV’s audio output to an audio input jack on this  
unit. You can connect by either a digital (optical) or  
analog audio cable. For digital audio, connect to  
DIGITAL OPTICAL IN 1 on the receiver subwoofer.  
To use the HDMI Control function when you are  
connected to a supported Pioneer plasma television,  
you must connect via HDMI.  
• Do not connect any speakers other than those  
supplied to this system.  
• Do not connect the supplied speakers to any  
amplifier other than the one supplied with this  
system. Connection to any other amplifier may result  
in malfunction or fire.  
• You must first set ‘TV Input’ to switch the audio from  
a plasma television with the HDMI Control function  
or to switch the input source of this unit to TV audio  
and operate your TV with the supplied remote control.  
For more information, see Operating Pioneer plasma  
televisions and TVs on page 17 and Audio input  
settings from plasma televisions (TV Input) on  
page 39.  
• After connecting the plugs, pull lightly on the cables  
to make sure that the ends of the cables are securely  
connected to the terminals. Poor connections can  
create noise and interruptions in the sound.  
• If the cables’ wires happen to be pushed out of the  
terminals, allowing the wires to come into contact  
with each other, it places an excessive additional  
load on the amp. This may cause the amp to stop  
functioning, and may even damage the amp.  
2
8
Connect the power cord.  
• Connect each power cord to the AC inlet on the  
receiver subwoofer. Connect each power cord to a  
wall socket in the following order.  
1. Receiver subwoofer  
1
5
If you have a DVD player or other source  
component you want to connect, connect it now before  
connecting the power cord in the next step.  
See page 33 for how to connect a digital source  
component.  
2. TV  
• Run the cords that are connected to the side panel of  
the receiver subwoofer over the back side of the unit,  
and replace the cover on the side panel.  
Note  
1 Make sure to connect a TV or monitor (for video sources) to take advantage of this system’s home theater potential. Please refer to the  
instruction manual supplied with your TV or monitor for connection details.  
2 • Do not use any power cord other than the one supplied with this system.  
• Do not use the supplied power cord for any purpose other than connecting to this system.  
• After connecting this unit to an AC outlet, a 15-second initialization process begins. You cannot carry out any operations during initialization.  
The HDMI indicator on the display unit blinks during initialization, and you can turn this unit on once it has stopped blinking.  
12  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and displays  
03  
CChaoptnert3rols and displays  
Display unit  
1
2
3
Top buttons  
4
5
6
7
1
STANDBY/ON  
Press to switch the receiver subwoofer on/into standby.  
2
INPUT SELECTOR (page 33)  
Press repeatedly to select one of the external audio  
inputs (HDMI 1 to HDMI 3, Digital 1, Digital 2, Analog,  
iPod or Front Audio In).  
3
VOL +/– buttons  
Use to adjust the volume.  
4
5
POWER ON indicator (Blue)  
Front panel display  
See page 14 for details.  
6
IR remote sensor (page 22)  
7
HDMI indicator (Red)  
Lights when this receiver subwoofer is connected to  
HDMI (HDCP) compatible component.  
Also lights during initialization, after you plug this unit  
into an AC outlet.  
13  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and displays  
Display  
03  
1
2
3
4
5
6
7
DIRECT STEREO F.S.SURR.  
ADV.SURR. PRO LOGIC  
LOUDNESS MIDNIGHT DNR DIALOG HDMI THROUGH  
QUIET  
TONE S.RTRV MCACC  
2
DIGITAL  
2
DTS 96/24  
DSD PCM  
8
9
10 11  
1
DIRECT  
8
Digital format indicators  
Lights when Direct Sound is selected (i.e. Effective  
Sound is off)(page 24).  
2DIGITAL  
Lights during playback of a Dolby Digital source  
(page 24).  
2
Listening mode indicators  
STEREO  
DTS  
Lights when the Stereo mode is selected or when a  
stereo source is being played back in the Auto  
listening mode (page 26).  
Lights during playback of a DTS source (page 24).  
DTS 96/24  
Lights during playback of a DTS 96/24 decoding  
(page 24).  
F.S.SURR.  
Lights when one of the Front Stage Surround  
Advance listening modes is selected (page 26).  
DSDPCM  
Lights during DSD (Direct Stream Digital) to PCM  
conversion with SACDs.  
ADV.SURR.  
Lights when one of the Advanced Surround listening  
modes is selected (page 25).  
PCM  
Lights during playback of PCM signals.  
3
2
PRO LOGIC II  
9
Character display  
Lights during Dolby Pro Logic II decoding (page 25).  
4
Sound processing indicators  
10 Tuner indicators  
Lights when any of the Loudness, Midnight, Quiet or tone  
controls feature is selected (page 27)  
Lights when a broadcast is being received.  
5
S.RTRV  
Lights when Sound Retriever is active (page 26).  
Lights when a stereo FM broadcast is being received  
in auto stereo mode.  
6
HDMI THROUGH  
Lights when HDMI Mode is set to Through Mode.  
7
MCACC  
Lights when FM mono reception is selected.  
Lights when MCACC Effect is switched on (page 27).  
Blinks during Auto MCACC Setup (page 23).  
11  
Lights when sleep timer is active (page 40).  
14  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and displays  
Remote control  
03  
1
RECEIVER  
Switches the receiver subwoofer to On/Standby.  
2
TV  
• For more information on using the remote control,  
see Operating the remote control on page 22.  
Switches the TV to On/Standby.  
TV CTRL  
Switches the remote control to the TV operating mode  
(no effect on the current input source of this unit).  
Operating the receiver subwoofer  
This section explains how to operate the remote control  
for the receiver subwoofer. Note that the controls change  
when you have chosen the input function for separate  
connected devices.  
3
SOURCE  
Switches the power for the selected component to On/  
Standby (page 22).  
4
Input select buttons  
Change the input for this unit. You will also need to press  
one of these buttons when operating another connected  
component via this remote control.  
2
RECEIVER  
SOURCE  
TV  
1
4
3
CTRL  
3
HDMI 1 to HDMI 3  
Switch input from HDMI 1 to HDMI 3.  
HDMI  
2
1
TV  
TV  
FM/AM  
LINE  
Switches to the input selected at TV Input setup  
(page 39).  
FM/AM (page 28)  
Switches between FM and AM bands.  
LINE (page 34)  
Press repeatedly to select one of the receiver  
subwoofer’s audio inputs (Digital 1, Digital 2,  
Analog, iPod or Front Audio In).  
5
5
LCD touch screen  
Displays the buttons used to control external  
components such as a receiver subwoofer, plasma  
television, DVD player, Blu-ray disc player, and HDD/DVD  
recorder. The current operating mode is displayed at the  
top of the remote control’s screen.  
Although the LCD touch screen disappears if you do not  
perform any operations for a while, it appears when the  
screen is touched or a button on the remote control is  
pressed.  
PAGE  
TOP MENU  
MENU  
6
6
Other component button  
DISC  
NAVIGATOR  
Use to operate an HDD/DVD recorder or other connected  
component.  
7
8
7
ꢀ/ꢁ/ꢂ/ꢃ (cursor buttons) and ENTER  
HOME  
MENU  
RETURN  
Use to control receiver functions.  
SETUP  
9
6
8
SETUP  
Use to access the menu system for surround sound  
setup, tuner settings and so on (page 28, 30 38 40).  
RECEIVER  
VOL  
,
,
9
RETURN  
RCV  
MUTE  
12  
10  
11  
Use to cancel settings.  
10 RCV  
Use to switch to the receiver subwoofer operating mode  
when this unit is in the other operating modes. Press  
again to return to the previous operating mode.  
11 VOL +/–  
Use to adjust the volume of the receiver subwoofer.  
15  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and displays  
03  
12 MUTE  
Operating the built-in FM/AM tuner  
Mutes the sound or restores the sound if it has been  
muted (adjusting the volume also restores the sound).  
TOP MENU  
MENU  
DISC  
NAVIGATOR  
LCD touch screen  
1
2
HOME  
MENU  
RETURN  
RECEIVER  
SETUP  
3
ADV.  
F.S.  
13  
SURR  
SURR SURR  
1
ꢀ/ꢁ/ꢂ/ꢃ (cursor buttons) and ENTER  
Use to control FM/AM tuner functions.  
SOUND  
DIRECT  
RTRV  
2
SETUP  
14  
15  
GENRE  
16  
Use to access the menu system or tuner settings.  
3
RETURN  
18  
19  
Use to cancel settings.  
TEST  
SOUND  
TONE  
MCACC  
SLEEP  
17  
20  
LCD touch screen  
21  
EXIT  
FM/AM  
13 SURR  
1
4
7
2
3
6
Use to select a Surround mode (page 24).  
ADV.SURR  
5
8
4
Use to change the audio setting to Pioneer’s original  
Advanced Surround mode (page 25).  
9
F.S.SURR  
Use to select a Front Stage Surround Advance mode  
(page 26).  
CLEAR  
0
TUNE  
5
6
-
-
+
+
14 GENRE  
Use to listen to audio in Genre Sync mode (page 26).  
(This button is displayed only when the RECEIVER screen  
is shown during HDD/DVD recorder operation.)  
ST  
4
5
Number buttons  
Use to directly choose a preset radio station.  
15 SOUND RTRV  
Press to restore CD quality sound to compressed audio  
sources (page 26).  
CLEAR  
Press to clear an entry and start again.  
16 DIRECT  
Use to switch on/off the Effective Sound mode (page 24).  
TUNE +/–  
Use to find radio frequencies.  
17 MCACC  
Starts the Auto MCACC setup (page 23).  
6
ST +/–  
Use to select a station preset.  
18 TEST TONE  
Use to output the test tone (for speaker setup) (page 32).  
19 SOUND  
Press to access the sound menu, from which you can  
adjust bass and treble, etc.  
20 SLEEP  
Press to set the sleep timer (page 40).  
21 EXIT  
Cancel settings and exit the RECEIVER screen.  
16  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and displays  
03  
Operating Pioneer plasma televisions and TVs  
First, refer to Setting up the remote to control your TV on page 40 for information about setting up your TV’s presets.  
Note that certain buttons may not work with some TVs.  
TV  
1
2
S
3
hown when not set to  
a Pioneer plasma television.  
RECEIVER  
SOURCE  
TV  
PDP  
1
3
2
CTRL  
1
4
7
2
3
6
5
8
8
9
PAGE  
9
TOP MENU  
MENU  
CH  
RTN  
CH  
ENTER  
DISC  
10  
0
NAVIGATOR  
12  
4
+
+
INPUT  
HOME  
MENU  
RETURN  
14  
11  
13  
SETUP  
P
TV VOL  
5
7
6
MUTE  
-
-
1
2
TV  
LCD touch screen  
Number buttons  
Switches the TV to On/Standby.  
8
TV CTRL  
Selects a channel.  
Switches the remote control to the TV operating  
mode (no effect on the current input source of this  
unit).  
9
CH RTN  
Returns to the previously selected channel.  
10 CH ENTER  
Executes a channel number.  
SOURCE  
Switches the power for the TV to On/Standby.  
11 P +/–  
Selects the channel.  
3
PAGE </>  
Switches pages on the LCD touch screen.  
12 INPUT  
Selects an input source of the TV.  
4
ꢀ/ꢁ/ꢂ/ꢃ (cursor buttons) and ENTER  
Use to navigate all on-screen displays. Press ENTER to  
select the currently highlighted option.  
13 MUTE  
Mutes the sound.  
5
HOME MENU  
Display the HOME MENU screen.  
14 TV VOL +/–  
Sets the volume.  
6
RETURN  
Restores the previous menu screen.  
7
Color (RED/GREEN/YELLOW/BLUE) buttons  
Selects a page.  
17  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and displays  
03  
Operating a Pioneer Blu-ray Disc player  
RECEIVER  
SOURCE  
TV  
BD 1/2  
BD 2/2  
1
CTRL  
9
1
4
2
3
6
5
8
0
2
13  
PAGE  
10  
11  
TOP MENU  
MENU  
7
9
3
5
4
7
DISC  
NAVIGATOR  
ꢈ/ꢉ  
ZOOM  
ꢊ/ꢋ  
DISP  
CLEAR  
ENTER  
HOME  
MENU  
PLAY  
MODE  
12  
DISP  
12  
RETURN  
14  
15  
SETUP  
6
8
VIDEO  
ADJ  
1
SOURCE  
10 Playback controls  
Switches the power for a Blu-ray disc player to  
On/Standby.  
Press to start or resume playback.  
2
PAGE </>  
Switch between pages on the LCD touch screen when  
multiple pages are present.  
Press to stop playback (you can resume playback by  
pressing ).  
3
TOP MENU / DISC NAVIGATOR  
Press to display the top menu of a BD-ROM or DVD-Video  
disc.  
Press to pause playback; press again to restart.  
, ꢅ  
When playing a DVD-R/-RW disc, press to display/exit the  
Disc Navigator.  
Press to start reverse/forward scanning.  
, ꢇ  
4
MENU  
Press to jump to the start of the previous/next  
chapter/track.  
BD-ROM: Press to display/hide the pop-up menu.  
DVD-Video: Press to display the disc menu (if there is one).  
/, /ꢋ  
5
ꢀ/ꢁ/ꢂ/ꢃ (cursor buttons) and ENTER  
Use for slow motion and step frame.  
Use to navigate on-screen displays and menus. Press  
ENTER to select an option or execute a command.  
11 ZOOM  
Press to zoom the screen when displaying a still image.  
6
HOME MENU  
12 DISP  
Press to display information.  
Press to display the player’s Home Menu, access most of  
the player’s functions.  
13 Number buttons  
7
RETURN  
Use to enter title, chapter or track numbers, etc.  
Press to return to a previous screen.  
ENTER  
8
Color (RED/GREEN/YELLOW/BLUE) buttons  
Press to select an option or execute a command.  
Use to navigate BD-ROM menus.  
CLEAR  
LCD touch screen  
Press to clear a numeric entry, etc.  
14 PLAY MODE  
9
(AUDIO)  
Press to change the Play Mode (repeat play, for example).  
Press to select the audio channel or language.  
15 VIDEO ADJ  
Press to display the Video Adjust screen.  
(SUBTITLE)  
Press to select a subtitle display.  
(ANGLE)  
Press to change the camera angle during BD-ROM  
or DVD-Video movie multi-angle scene playback.  
18  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and displays  
03  
Operating a Pioneer DVD player  
RECEIVER  
SOURCE  
TV  
DVD 1/2  
DVD 2/2  
1
CTRL  
8
9
1
4
2
3
6
9
ꢈ/  
ꢉꢄ  
ꢋ/  
ꢊꢅ  
12  
13  
5
8
2
PAGE  
7
TOP MENU  
MENU  
3
5
6
4
7
DISC  
NAVIGATOR  
ENTER  
CLEAR  
0
PLAY  
MODE  
HOME  
MENU  
ZOOM  
DISP  
11  
DISP  
11  
10  
RETURN  
SETUP  
1
SOURCE  
9
Playback controls  
Switches the power for a DVD player to On/Standby.  
Press to start or resume playback.  
2
PAGE </>  
Switch between pages on the LCD touch screen when  
multiple pages are present.  
Press to stop playback (you can resume playback by  
pressing ).  
3
TOP MENU  
Press to display the top menu of a DVD-Video disc.  
Press to pause playback; press again to restart.  
4
MENU  
Displays a DVD disc menu – this varies with the disc and  
may be the same as the ‘top menu’.  
/ꢉ ꢄ, /ꢊ ꢅ  
Press to start reverse or forward scanning. Press  
again to change the speed.  
5
ꢀ/ꢁ/ꢂ/ꢃ (cursor buttons) and ENTER  
While paused, press and hold to start slow-motion  
playback. Press repeatedly to change the playback  
speed.  
Moves the cursor around the screen. Press ENTER to select  
the current menu option.  
6
HOME MENU  
While paused, press to advance a single frame in  
either direction.  
Display/exit the on-screen display.  
7
RETURN  
/ ꢇ  
Returns to the previously displayed menu screen.  
Press to skip to the previous or next title/chapter/  
track/folder; or to display the previous or next menu  
page.  
LCD touch screen  
10 ZOOM  
8
(AUDIO)  
Press to zoom the screen when displaying a still image.  
Press to select the audio channel or language.  
11 DISP  
Press to display information.  
(SUBTITLE)  
Press to select a subtitle display.  
12 Number buttons  
(ANGLE)  
Use to enter title, chapter or track numbers, etc.  
Press to change the camera angle during DVD-Video  
movie multi-angle scene playback.  
ENTER  
Press to select an option or execute a command.  
CLEAR  
Press to clear a numeric entry, etc.  
13 PLAY MODE  
Press to change the Play Mode (repeat play, for example).  
19  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and displays  
03  
Operating a Pioneer HDD/DVD Recorder  
RECEIVER  
SOURCE  
TV  
HDD/DVR 1/2  
HDD/DVR 2/2  
1
CTRL  
8
9
HDD  
DVD  
1
4
7
2
5
8
0
3
6
13  
14  
2
PAGE  
9
TOP MENU  
DISC  
MENU  
3
5
6
4
7
NAVIGATOR  
ꢊ/ꢋ  
CLEAR  
ꢈ/ꢉ  
15  
16  
CM  
BACK SKIP  
CM  
JUKE  
BOX  
+
HOME  
MENU  
11  
INPUT DISP  
10  
12  
RETURN  
SETUP  
CH  
STOP  
REC  
REC  
ì
17  
-
1
SOURCE  
LCD touch screen  
Switches the power for a HDD/DVD recorder to  
On/Standby.  
8
HDD  
Press to select the hard disk (HDD) for recording and  
playback.  
2
PAGE </>  
Switch between pages on the LCD touch screen when  
multiple pages are present.  
DVD  
Press to select the DVD for recording and playback.  
3
TOP MENU / DISC NAVIGATOR  
9
Playback controls  
Press to display the top menu if a DVD-Video or finalized  
DVD-R/-RW (Video) disc is loaded, or the Disc Navigator  
screen.  
Press to start playback.  
4
MENU  
Press to display the disc menu if a DVD-Video, finalized  
DVD-R/-RW or finalized DVD+R/+RW disc is loaded.  
Press to stop playback.  
5
ꢀ/ꢁ/ꢂ/ꢃ (cursor buttons) and ENTER  
Press to pause playback or recording.  
Use to navigate all on-screen displays. Press ENTER to  
/ ꢅ  
select the currently highlighted option.  
Press to start reverse or forward scanning. Press  
again to change the speed.  
6
HOME MENU  
Press to display the Home Menu, from which you can  
navigate all the functions of the recorder.  
/ ꢇ  
Press to skip to the previous or next title/ chapter/  
track/folder; or to display the previous or next menu  
page.  
7
RETURN  
Press to go back one level in the on-screen menu or  
display.  
/, /ꢋ  
While paused, press and hold to start slow-motion  
playback. Press repeatedly to change the playback  
speed.  
While paused, press to advance a single frame in  
either direction.  
10 CM BACK (commercial back)  
Press repeatedly to skip progressively backward  
through the video playing.  
CM SKIP (commercial skip)  
Press repeatedly to skip progressively forward  
through the video playing.  
20  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and displays  
03  
11 JUKEBOX  
Press to display the Jukebox screen of a HDD/DVD  
recorder, from which you can copy music to the HDD for  
playback.  
Putting the batteries in the remote  
control  
1
Open the battery compartment cover on the  
12  
(AUDIO)  
back of the remote control.  
Press to change the audio language or channel.  
(When the recorder is stopped, press to change the  
tuner audio.)  
2
Insert four AA/LR6 alkaline batteries into the  
battery compartment following the indications  
(,) inside the compartment.  
(SUBTITLE)  
Press to display/change the subtitles included in  
multilingual DVD-Video discs.  
(ANGLE)  
Press to switch camera angles on discs with multi-  
angle scenes.  
13 Number buttons  
Use the number buttons for track/chapter/title  
selection; channel selection, and so on.  
3
Close the cover.  
CLEAR  
Press to clear an entry and start again.  
14 CH +/–  
Caution  
Press to change the channel of the built-in TV tuner.  
Incorrect use of batteries can result in hazards such  
as leakage and bursting. Please observe the  
following:  
15 INPUT  
Press to change a HDD/DVD recorder input to use for  
recording.  
• Don’t mix new and old batteries together.  
16 DISP  
• Don’t use different kinds of battery together —  
although they may look similar, different batteries  
may have different voltages.  
Displays/changes the on-screen information displays.  
17 Recording controls  
• Make sure that the plus and minus ends of each  
battery match the indications in the battery  
compartment.  
ì REC  
Press to start recording. Press repeatedly to set the  
recording time in blocks of 30 mins.  
• Remove batteries from equipment that isn’t going to  
be used for a month or more.  
STOP REC  
Press to stop recording.  
• When disposing of used batteries, please comply with  
governmental regulations or environmental public  
instruction’s rules that apply in your country /area.  
WARNING  
• Do not use or store batteries in direct sunlight or  
other excessively hot place, such as inside a car or  
near a heater. This can cause batteries to leak,  
overheat, explode or catch fire. It can also reduce the  
life or performance of batteries.  
21  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Controls and displays  
03  
Choosing and operating a source component  
Using the remote control  
HDMI  
Please keep in mind the following when using the remote  
control:  
TV  
FM/AM  
LINE  
1
2
3
1
Press to cycle through connected components.  
The selected component changes, and the LCD screen  
on the remote control changes to that of the appropriate  
component.  
• Make sure that there are no obstacles between the  
remote and the remote sensor on the unit.  
• Remote operation may become unreliable if strong  
sunlight or fluorescent light is shining on the unit’s  
remote sensor.  
• To select input for Digital 1, Digital 2, Analog, Front  
Audio In, or iPod, press the LINE button until the  
desired input function is shown on the display unit.  
• Remote controllers for different devices can interfere  
with each other. Avoid using remotes for other  
equipment located close to this unit.  
2
Choose the input source you are using when you  
have selected HDMI 1 to HDMI 3 or LINE.  
The LCD screen changes to that for the selected  
component, and you can then operate the desired  
component.  
• Replace the batteries when you notice a fall off in the  
operating range of the remote.  
• Use within the operating range in front of the remote  
control sensor on the display unit, as shown.  
HDD/  
DVR  
HDD/  
DVR  
BD  
DVD  
BD  
DVD  
TV  
30  
30  
EXIT  
EXIT  
HDMI input  
LINE input  
7 m  
• When the desired source cannot be found, or when  
you have a component not manufactured by Pioneer  
connected, press RCV to put the remote control into  
Receiver mode. The input for this unit remains  
unchanged.  
Operating the remote control  
Note  
The supplied remote control can control not only the  
receiver subwoofer, but also other Pioneer products such  
as a plasma television, DVD player, Blu-ray disc player,  
and HDD/DVD recorder.  
To temporarily control the receiver while listening to  
audio from a connected component on this unit,  
press RCV. The selected input will not change, and  
the remote changes to Receiver mode. To return to  
the previous operating mode, press RCV once more.  
To operate these components, orient the remote control  
toward the display unit.  
Using the LCD touch screen  
Operating the receiver subwoofer  
Depending on the type of connected component you are  
operating (such as DVD player), there may be multiple  
pages of information for the LCD touch screen. When the  
component you would like to control is not displayed,  
press PAGE to scroll to the page where the component  
you would like to control is located.  
RCV  
Press to display the RECEIVER screen.  
The RECEIVER screen is shown on the remote control’s  
LCD screen, and the remote is switched to Receiver  
mode.  
• When no operations are carried out for over 10  
seconds, the display on the LCD touch screen of the  
remote control is automatically turned off. To have  
the display shown once again, either touch the LCD  
or press a button on the remote control.  
RECEIVER  
ADV  
F.S.  
SURR  
SURR SURR  
22  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Getting started  
04  
Chapter 4  
Getting started  
1
Connect the microphone to the MCACC SETUP  
Important  
MIC jack on back of the display unit.  
RCV  
Press to set the remote control to receiver  
control mode in order to operate the receiver  
subwoofer (make sure that the LCD displays the  
RECEIVER screen, as shown below).  
2
Place the microphone at your normal listening  
position.  
Place it about ear height, and make sure it is level by  
using a table or chair.  
Make sure there are no obstacles between the speakers  
and the microphone.  
RECEIVER  
RECEIVER  
ADV  
F.S.  
SURR  
SURR SURR  
3
If the receiver subwoofer is off, press  
RECEIVER to turn the power on.  
MCACC  
4
Press MCACC.  
Using the Auto MCACC setup for  
optimal surround sound  
Try to be as quiet as possible after pressing MCACC. The  
volume increases automatically and the system outputs  
a series of test tones.  
The Multichannel Acoustic Calibration (MCACC) system  
measures the acoustic characteristics of your listening  
area, taking into account ambient noise, and testing for  
channel delay and channel level. After you have set up  
the microphone provided, the system uses the  
• To cancel Auto MCACC setup before it has finished,  
press MCACC. The unit will continue to use the  
previous settings.  
• If the ambient noise level is too high, Noisy! blinks in  
information from a series of test tones to measure  
standing wave and reverb, optimizing the speaker  
settings and equalization (MCACC Effect) for your  
the display for five seconds. To exit and check the  
2
noise levels , press MCACC, or to try again, press  
1
ENTER when Retry shows in the display.  
particular room.  
• If you see an Error MIC! or Error Speaker! message  
in the display, there may be a problem with your mic  
or the speaker connections. To try again, press  
Important  
3
• The test tones used for Auto MCACC setup are loud;  
however, do not turn the volume down during setup  
as this may result in a sub-optimal setup.  
ENTER .  
When the MCACC setup is complete, the volume level  
4
returns to normal, Complete shows in the display, and  
• Make sure the microphone and speakers are not  
moved during the MCACC setup.  
5
MCACC Effect is activated.  
• Be sure to disconnect the microphone from this unit  
upon completion of the Auto MCACC setup.  
Note  
1 You only need to use the Auto MCACC setup once (unless you change the placement of your speakers or your room layout).  
2 • If the room environment is not optimal for the Auto MCACC setup (too much ambient noise, echo off the walls, obstacles blocking the speak-  
ers from the microphone) the final settings may be incorrect. Check for household appliances (air conditioner, fridge, fan, etc.), that may be  
affecting the environment and switch them off if necessary.  
• Some older TVs may interfere with the operation of the mic. If this seems to be happening, switch off the TV during Auto MCACC setup.  
3 If this doesn’t work, press MCACC, turn off the power, and check the problem indicated by the Error message, then try the Auto MCACC setup  
again.  
4 If Complete doesn’t appear, it is likely an error occurred during the setup. Please check all connections and try again.  
5 See Listening with MCACC Effect on page 27 to switch on/off MCACC Effect.  
23  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening to your system  
05  
Chapter 5  
Listening to your system  
Stereo Playback in Surround  
Important  
Outputs audio from the surround speakers while  
directing vocal sound to the front channels. You can  
play back stereo sources like CDs in seamless,  
comfortable surround sound.  
This effect is available when you play back stereo  
sources in the Auto listening mode (see below).  
RCV  
Press to set the remote control to receiver  
control mode in order to operate the receiver  
subwoofer (make sure that the LCD displays the  
RECEIVER screen, as shown below).  
The Effective sound mode can be turned off (activating  
Direct mode) by doing the following:  
RECEIVER  
ADV  
F.S.  
SURR  
SURR SURR  
DIRECT  
Press to switch to Direct Sound.  
Press this button to switch between Effective Sound and  
Direct Sound.  
• When Direct Sound is selected, the DIRECT indicator  
lights.  
Effective Sound (for optimum sound)  
With the uniquely shaped high-quality speakers supplied  
with this unit, the Effective Sound mode enables the  
following Pioneer exclusive audio technologies designed  
to maximize the real experience of sound originally  
inherent in movies and music.  
Auto listening mode  
The Auto listening mode is the simplest way to listen to  
any source as it was mastered: the output from the  
speakers mirrors the channels in the source material.  
Turn on the Effective Sound mode under normal  
circumstances to maximize the capabilities of this unit.  
If you set up the system for Front surround (page 6), the  
Front Stage Surround modes will give the best results  
(see page 26).  
Dialogue Enhancement  
Clarifies dialogue in movies to make it stand out from  
other background sounds.  
Dynamic Range Compression  
SURR  
Press to select the Auto listening mode.  
Resuscitates detailed sound susceptible to ambient  
noise to create an acoustic environment where you  
feel as if you are right in the action.  
Listening in surround sound  
Original Channel Balance & Channel Mix  
Since the orientation of the supplied speaker units is  
uniquely designed, channels are mixed down and  
balanced in a special manner. Also, the optimum  
balance is automatically achieved according to the  
contents being played back.  
You can listen to stereo or multichannel sources in  
surround sound. Surround sound is generated from  
stereo sources using one of the Dolby Pro Logic or DTS  
1
Neo:6 decoding modes.  
If you set up the system for Front surround (page 6), the  
Front Stage Surround modes will give the best results  
(see page 26).  
Frequency Characteristic Correction  
Realizes the playback characteristic optimized for  
long hours of listening in addition to the added  
features of the supplied speaker units.  
SURR  
Press repeatedly to select a listening mode.  
The choices that appear in the display will vary according  
2
to the type of source that’s playing.  
Note  
1 After the surround back signals of the 6.1/7.1-channel audio represented by DTS-ES are properly decoded, the original virtual surround back  
function outputs the surround back signals in combination with surround signals.  
2 You cannot select a mode other than Auto and Stereo while playing back DTS-HD, DTS-Express, or Dolby TrueHD (176.4 kHz/192 kHz). Also,  
you cannot select DTS Neo:6 for Dolby Digital Plus or Dolby TrueHD (below 96 kHz).  
24  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening to your system  
05  
With two channel sources, you can select from:  
Panorama – Extends the front stereo image to  
include the surround speakers for a ‘wraparound’  
effect.  
Auto – Auto listening mode (see page 24)  
2PL II Movie (Dolby Pro Logic II Movie) – 5.1  
channel surround sound, especially suited to movie  
sources  
ENTER  
3
Adjust the setting, then press ENTER to  
2PL II Music (Dolby Pro Logic II Music) – 5.1  
channel surround sound, especially suited to music  
sources; see Dolby Pro Logic II Music settings below  
confirm.  
Center image setting  
2PL II Game (Dolby Pro Logic II Game) – 5.1  
channel surround sound, especially suited to video  
games  
When listening to two channel sources in Neo:6 Music  
mode (see page 24), you can also adjust the center image  
effect.  
2Pro Logic (Dolby Pro Logic) – 4.1 channel  
surround sound for use with any two-channel source  
Adjusts the center image to create a wider stereo effect  
2
with vocals.  
Neo:6 Cinema – 6.1 channel sound, especially suited  
to movie sources  
SOUND  
1
Press when Neo:6 Music mode is active.  
Neo:6 Music 6.1 channel sound, especially suited to  
music sources; see Center image setting below  
ENTER  
Stereo – See Listening in stereo on page 26  
2
3
Select ‘Center Image’ then press ENTER.  
Adjust the setting, then press ENTER to  
With multichannel sources, you can select (according to  
format):  
ENTER  
Auto – Auto listening mode (see page 24)  
StandardDecode – Listening in Dolby Digital or DTS  
surround decoding. Plays back multichannel  
sources like Dolby Digital, DTS, and multichannel  
PCM with the most standard decoder  
confirm.  
• Adjust the effect from 0 (all center channel sent to  
front right and left speakers) to 10 (center channel  
sent to the center speaker only).  
Stereo – See Listening in stereo on page 26  
Using Advanced Surround  
Dolby Pro Logic II Music settings  
When listening in Dolby Pro Logic II Music mode (see  
above), there are three settings you can adjust: Center  
Width, Dimension, and Panorama.  
The Advanced Surround effects can be used with any  
multichannel or stereo source for a variety of additional  
surround sound effects. These modes are designed to  
provide optimum listening effect when using the  
Standard surround setup described on page 6.  
SOUND  
1
Press when Dolby Pro Logic II Music mode is  
active.  
ADV  
SURR  
Press to select an Advanced Surround mode.  
The ADV.SURR. indicator lights when one of these  
ENTER  
modes is chosen. You cannot switch between modes for  
2
Select ‘Center Width’, ‘Dimension’ or  
3
some audio streams.  
‘Panorama’ then press ENTER.  
Press repeatedly to select:  
Action – Designed for action movies with dynamic  
soundtracks  
1
Center Width – Provides a better blend of the front  
speakers by spreading the center channel between  
the front right and left speakers, making it sound  
wider (higher settings) or narrower (lower settings).  
Drama – Designed for movies with lots of dialog  
Sci-Fi – Designed for science fiction with lots of  
Dimension – Adjusts the depth of the surround  
sound balance from front to back, making the sound  
more distant (minus settings), or more forward  
(positive settings).  
special effects  
Mono Film – Creates surround sound from mono  
soundtracks  
Note  
1 As this product uses a dual center speaker system, you should normally use the C.Width 3 setting.  
2 As this product uses a dual center speaker system, you should normally use the C.Image 3 setting.  
3 You cannot use this function for the following audio streams:  
• Dolby TrueHD: over 88.2 kHz  
• DTS-HD: over 88.2 kHz or with the channel format of 2/0  
• DTS-Express: with the channel format of 2/0  
25  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening to your system  
05  
Ent.Show – Suitable for musical sources  
Expanded – Creates an extra wide stereo field  
TV Surround – Provides surround sound for both  
mono and stereo TV sources  
Advanced Game – Suitable for video games  
Sports – Suitable for sports programs  
Classical – Gives a large concert hall-type sound  
Rock/Pop – Creates a live concert sound for rock  
and/or pop music  
Genre Sync Mode  
Only when you have this unit connected to an HDMI  
Control-compatible Pioneer HDD/DVD recorder and are  
using the HDMI Control function, you can make use of  
the Genre Sync Mode to have the listening mode  
automatically change to that which best matches the  
genre of the contents playing from the recorder.  
• Set the HDMI Mode to AMP Mode (page 36).  
Unplugged – Suitable for acoustic music sources  
Ext.Stereo – Gives multichannel sound to a stereo  
source, using all of your speakers  
GENRE  
Press when listening to media contents  
from a recorder.  
The most appropriate listening mode is selected and  
shown in the display. When the related genre could not  
be determined, No Genre or Can’t use may be displayed  
and the listening mode remains unchanged.  
Using Front Stage Surround Advance  
The Front Stage Surround Advance modes are effective  
when you are using the Front surround speaker setup as  
described on page 6.  
Tip  
• Mainly used with Jukebox and MP3 sources.  
F.S.  
SURR  
Press to select a Front Stage Surround  
• To use this function, you must have an HDMI Control-  
compatible Pioneer HDD/DVD recorder connected via  
HDMI, and have the HDMI Control function set to On.  
Advance mode.  
The F.S.SURR indicator lights.  
Press repeatedly to select Focus 5.1ch, Wide 5.1ch or  
Extra Power. You cannot select a mode other than Extra  
1
Power for some audio streams.  
Using the Sound Retriever  
Focus 5.1ch – Use to provide a rich surround sound  
effect directed to the center area where the left and  
right speakers sound projection converges.  
When audio data is removed during the MP3 or WMA  
compression process, sound quality often suffers from  
an uneven sound image. The Sound Retriever feature  
employs new DSP technology that helps bring CD quality  
sound back to compressed two channel audio by  
restoring sound pressure and smoothing jagged artifacts  
left over after compression.  
Wide 5.1ch – Use to provide a surround sound effect  
to a wider area than Focus 5.1ch mode.  
Extra Power Outputs stereo sound (in the case of  
multi-channel sources, down-mixed stereo sound)  
from the surround speakers for powerful stereo effect.  
SOUND  
2
RTRV  
Press while listening to a stereo source .  
Press repeatedly to switch between:  
Listening in stereo  
Retriever On — Switches the Sound Retriever on.  
Retriever Off — Switches the Sound Retriever off.  
You can listen to any source — stereo or multichannel —  
in stereo. When playing a multichannel source, all  
channels are downmixed to the front left/right speakers  
and the subwoofer.  
SURR  
Press repeatedly until STEREO shows in the  
display.  
Note  
1 You cannot use this function for the following audio streams:  
• Dolby TrueHD: over 88.2 kHz  
• DTS-HD: over 88.2 kHz or with the channel format of 2/0  
• DTS-Express: with the channel format of 2/0  
2 This setting cannot be used with multichannel sources. Also, in case of SACD, DTS-HD, DTS-Express, Dolby TrueHD, Dolby Digital Plus, and  
PCM (192 kHz/176.4 kHz), even stereo sources cannot be used.  
26  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening to your system  
Listening with MCACC Effect  
05  
Adjusting the bass and treble  
Listen to sound using the corrected acoustic field  
settings obtained by MCACC.  
Use the bass and treble controls to adjust the overall tone.  
SOUND  
1
2
3
Press to open the sound menu.  
Select ‘Tone’ then press ENTER.  
SOUND  
1
2
3
Press to open the sound menu.  
ENTER  
1
ENTER  
Select ‘MCACC Effect’ then press ENTER.  
ENTER  
S
elect ‘Bass/Treble’ then press ENTER.  
ENTER  
• Selecting Bass/Treble cancels the Midnight,  
Loudness and Quiet listening modes. These modes  
cannot be used at the same time.  
Switch ’MCACC On’ or ‘MCACC Off’ then  
press ENTER to confirm.  
• When MCACC Effect is off, equalization, channel  
delay, channel level and standing wave are set to off.  
ENTER  
• When MCACC Effect is off, the channel delay and  
channel level can be adjusted manually and the  
settings stored separately from when MCACC Effect  
is on.  
4
Use the ꢂ/ꢃ buttons to select ‘Bass’ or  
’Treble’; use the ꢀ/ꢁ buttons to adjust the sound  
then press ENTER to confirm.  
• Bass and Treble can be adjusted from -6dB to +6dB.  
• MCACC Effect is set to on automatically after Auto  
MCACC setup is used.  
• When the Bass or Treble is set to something other  
than 0dB, the TONE indicator lights.  
Using Midnight, Loudness and Quiet  
listening modes  
Adjusting sound delay  
The Midnight listening feature allows you to hear  
Some monitors have a slight delay when showing video,  
so the soundtrack will be slightly out of sync with the  
picture. By adding a bit of delay, you can adjust the sound  
to match the presentation of the video.  
effective surround sound of movies at low volume levels.  
The Loudness listening feature can be used to get good  
bass and treble from music sources at low volume levels.  
There are a total of 60 steps (levels) that you can adjust,  
with a total range of 200 msec.  
The Quiet listening feature reduces excessive bass or  
treble in a sound source.  
SOUND  
SOUND  
1
2
3
Press to open the sound menu.  
1
2
3
Press to open the sound menu.  
Select ‘Tone’ then press ENTER.  
ENTER  
ENTER  
1
Select ‘Sound Delay’ then press ENTER.  
ENTER  
ENTER  
S
elect ‘Midnight’, ‘Loudness’ or ‘Quiet’  
Select the length of the delay in sound,  
2
then press ENTER to confirm.  
then press ENTER to confirm.  
• To cancel the Midnight, Loudness or Quiet listening  
• This option is deactivated and not displayed if you  
have AutoDelay set to On in HDMI Setup (see Setting  
the Auto Delay on page 39).  
modes, select Bass/Treble.  
Note  
1 While playing back DTS-HD (over 88.2 kHz) or Dolby TrueHD (over 88.2 kHz) audio streams, you cannot select Tone if a mode other than Bass/  
Treble is selected.  
2 While playing back DTS-HD (over 88.2 kHz) or Dolby TrueHD (over 88.2 kHz) audio streams, you cannot select a mode other than Bass/Treble.  
27  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening to the radio  
06  
Chapter 6  
Listening to the radio  
Improving poor FM reception  
Important  
If you’re listening to an FM station in stereo but the  
reception is weak, you can improve the sound quality by  
switching to mono.  
FM/AM  
To listen to the radio, press the FM/AM button  
to set the remote control to FM/AM control mode. The  
LCD screen on the remote control changes to the  
FM/AM screen.  
SETUP  
1
2
3
Press after tuning to an FM radio station.  
Select ‘Tuner Setup’ then press ENTER.  
Choose ‘FM Auto/Mono’ then press  
ENTER  
FM/AM  
1
2
3
ENTER  
ENTER.  
Listening to the radio  
ENTER  
The tuner can receive both FM and AM broadcasts, and  
lets you memorize your favorite stations so you don’t have  
to manually tune in every time you want to listen.  
4
Select ’FM Mono’ then press ENTER.  
The mono indicator ( ) lights when the tuner is in mono  
reception mode.  
1
FM/AM Switch to the tuner, then press repeatedly to  
Select FM Auto above to switch back to auto-stereo  
select the FM or AM band.  
The display shows the band and frequency.  
mode (the stereo indicator (  
stereo broadcast).  
) lights when receiving a  
TUNE  
-
+
2
Tune to a frequency.  
Improving poor AM sound  
There are three tuning modes — manual, auto, and high-  
speed:  
The simplest way to improve the sound quality of AM  
radio is to make sure that the TV in the room is switched  
off. Also try changing the position and direction of the  
AM loop antenna.  
Manual tuning – Press TUNE +/– repeatedly to  
change the displayed frequency.  
Auto tuning – Press and hold TUNE +/– until the  
frequency display starts to move, then release. The  
tuner will stop on the next station it finds. Repeat to  
keep searching.  
Changing the noise cut mode  
If you find that the AM sound quality is bad even after  
trying the above, you may be able to improve it using a  
different noise cut mode. Just choose the one that  
sounds best.  
High-speed tuning – Press and hold TUNE +/– until  
the frequency display starts to move rapidly. Keep the  
button held down until you reach the frequency you  
want. If necessary, fine tune the frequency using the  
manual tuning method.  
SETUP  
1
2
3
4
Press after tuning to an AM radio station.  
ENTER  
ENTER  
ENTER  
Select ‘Tuner Setup’ then press ENTER.  
Choose ‘Noise Cut’ then press ENTER.  
Select a Noise cut mode (1, 2 or 3) then  
press ENTER.  
28  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Listening to the radio  
Memorizing stations  
06  
Changing the frequency step  
If you find that you can’t tune into stations successfully,  
the frequency step may not be suitable for your country/  
region.  
You can save up to 30 station presets so that you always  
have easy access to your favorite stations without having  
to tune in manually each time.  
1
Tune to an FM or AM radio station.  
SETUP  
1
2
3
4
Press SETUP.  
Select mono or auto-stereo reception (FM) or the Noise  
Cut mode (AM) as necessary. These settings are saved  
along with the preset.  
ENTER  
Select ‘System Setup’ then press ENTER.  
SETUP  
2
3
4
Press SETUP.  
ENTER  
ENTER  
ENTER  
ENTER  
Select ‘AM9K/10K’, then press ENTER  
.
Select ‘Tuner Setup’ then press ENTER.  
ENTER  
Select a setting then press ENTER to  
Choose ‘ST.Memory’ then press ENTER  
.
confirm.  
AM 9K – 9 kHz step for AM;  
50 kHz step for FM  
5
Select the station preset you want then  
.
AM 10K – 10 kHz step for AM;  
press ENTER  
100 kHz step for FM  
Listening to station presets  
1
2
Make sure the tuner function is selected.  
ST  
-
+
Select a station preset.  
• Alternatively, use the number buttons to select a  
preset directly.  
29  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Surround sound settings  
07  
CShuaprterr o7 und sound settings  
SETUP  
1
2
3
Press SETUP.  
Important  
RCV  
Press to set the remote control to receiver  
control mode in order to operate the receiver  
subwoofer (make sure that the LCD displays the  
RECEIVER screen, as shown below).  
ENTER  
Select ‘Sound Setup’ then press ENTER.  
Select ‘ChannelLevel’, then press ENTER.  
Use the ꢂ/ꢃ buttons to select a channel  
ENTER  
RECEIVER  
ADV  
F.S.  
SURR  
SURR SURR  
4
or the ꢀ/ꢁ buttons to adjust the level of that  
channel.  
2
• You can adjust the level of each channel by 10 dB.  
Using the Sound Setup menu  
ENTER  
From the Sound Setup menu you can access all the  
surround sound settings of the system.  
5
Press once when you’re finished.  
• If you use the Auto MCACC feature again, it will  
overwrite the settings you have made here.  
During setup, the speakers are represented by the  
following letters:  
L – Front left speaker  
C – Center speaker  
1
Speaker distance setting  
The Auto MCACC feature (see page 23) should give you  
the best surround sound setup. However you may find  
that by further adjustment of the speaker distance  
settings you can improve the surround sound in your  
listening room.  
R – Front right speaker  
SR – Surround right speaker  
SL – Surround left speaker  
SW – Subwoofer  
Set the distance of each speaker from your normal  
listening position.  
1
Channel level setting  
ENTER  
The Auto MCACC feature (see page 23) should give you  
the best surround sound setup. However you may find  
that by further adjustment of the channel levels you can  
improve the surround sound in your listening room.  
SETUP  
1
2
3
Open the ‘Sound Setup’ menu.  
ENTER  
Select ‘Distance’ then press ENTER.  
This method of setting the channel levels allows you to  
listen to a source and adjust the levels of each playback  
channel.  
A further method of setting the channel levels is to use  
the test tone method. See Adjusting the channel levels  
using the test tone on page 32 for more on this.  
Use the ꢂ/ꢃ buttons to select a speaker  
or the ꢀ/ꢁ buttons to adjust the distance.  
Each speaker can be adjusted from 0.1m to 9.0m.  
ENTER  
4
Press ENTER when you’re finished.  
• If you use the Auto MCACC feature again, it will  
overwrite the settings you have made here.  
Note  
1 When this function is set while MCACC Effect is on, the value for the same function adjusted with the Auto MCACC feature is overwritten.  
When MCACC Effect is off, the value set here is applied, regardless of the value adjusted with the Auto MCACC feature. (The Auto MCACC  
setting is not overwritten.)  
2 The range of adjustment is limited when the volume level is set over 51.  
30  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Surround sound settings  
07  
Dynamic Range Control  
Dual mono setting  
When watching Dolby Digital or DTS material at low  
volume, low level sounds — including some of the dialog  
— can be difficult to hear properly. Using one of the  
Dynamic Range Control (DRC) settings can help by  
bringing up the low level sounds, while controlling high  
level peaks.  
Specifies how dual mono encoded Dolby Digital  
soundtracks should be played. You can also use this  
setting to switch the audio channel on DVD-RW discs  
recorded with bilingual audio.  
ENTER  
SETUP  
Dynamic Range Control works only with Dolby Digital  
soundtracks and some DTS soundtracks.  
1
2
3
Open the ‘Sound Setup’ menu.  
Select ‘Dual Mono’, then press ENTER.  
Select a setting.  
ENTER  
ENTER  
SETUP  
1
2
3
Open the ‘Sound Setup’ menu.  
Select ‘D.R.C.’, then press ENTER.  
Select a setting.  
ENTER  
Select one of the following:  
CH1 Mono – Only channel 1 is played  
CH2 Mono – Only channel 2 is played  
CH1/CH2 – Both channels are played through the  
front speakers  
Select one of the following:  
D.R.C. Auto – Only available for Dolby TrueHD  
signals. Select D.R.C. High or D.R.C. Mid for signals  
other than Dolby TrueHD.  
ENTER  
4
Press to exit.  
D.R.C. High – Dynamic range is reduced (loud  
sounds are reduced in volume while quieter sounds  
are increased)  
D.R.C. Mid – Mid setting  
D.R.C. Off – No dynamic range adjustment (use  
when listening at higher volume)  
ENTER  
4
Press to exit.  
31  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Surround sound settings  
07  
Using the Virtual Surround Back mode  
This mode allows you to hear a virtual surround back  
channel through your surround speakers. You can  
choose to listen to sources with no surround back  
channel information, or if the material sounds better in  
the format (for example, 5.1) for which it was originally  
encoded, you can have the receiver only apply this effect  
Adjusting the channel levels using  
the test tone  
If you prefer, you can set the channel levels using a test  
tone as a reference, rather than playing a source (see  
Channel level setting on page 30). A test tone is played  
through each speaker in turn, allowing you to adjust the  
level as it plays.  
1
to 6.1 encoded sources like Dolby Digital EX or DTS-ES.  
You can also adjust the channel levels for surround  
sound using test tone.  
ENTER  
SETUP  
1
2
3
Open the ‘Sound Setup’ menu.  
Select ‘Virtual SB’, then press ENTER.  
Select a setting.  
TEST  
TONE  
1
Carry out tone testing.  
ENTER  
The test tone is output from each speaker in turn.  
Adjust the volume level below 50.  
2
Adjust the channel level of a tune while it  
Select one of the following:  
is playing.  
Vir.SB On – Virtual Surround Back is always used (for  
example, on 5.1 encoded material)  
The aim is to adjust the levels so that you hear the test  
tone at the same volume from each speaker. You can  
adjust the level of each channel by 10 dB.  
Vir.SB Auto – Virtual Surround Back is automatically  
applied to 6.1 encoded sources (for example, Dolby  
Digital EX or DTS-ES), DTS Neo:6 or Advanced  
Surround mode  
• You can adjust the overall volume of test tone output  
using the VOL +/– buttons (this does not affect the  
channel level settings).  
• Because of the ultra low frequencies the subwoofer  
produces, it may sound quieter than it really is. We  
suggest adjusting the subwoofer level while listening  
to a source. See the method described in Channel  
level setting on page 30.  
Vir.SB Off – Virtual Surround Back mode is switched  
off  
ENTER  
4
Press to exit.  
ENTER  
3
Press to exit test tone setup once you have  
LFE Attenuate  
Some Dolby Digital and DTS audio sources include ultra-  
low bass tones.  
finished.  
• If you use the Auto MCACC feature again, it will  
overwrite the settings you have made here.  
Set the LFE attenuator as necessary to prevent the ultra-  
low bass tones from distorting the sound from the  
speakers.  
The LFE is not limited when set to 0dB, which is the  
recommended value. When set to -5dB, -10dB, -15dB or  
-20dB, the LFE is limited by the respective degree. When  
Off is selected, no sound is output from the LFE channel.  
ENTER  
SETUP  
1
2
3
Open the ‘Sound Setup’ menu.  
Select ‘LFE ATT’, then press ENTER.  
Adjust the setting then press ENTER to  
ENTER  
ENTER  
confirm.  
Note  
1 Depending on the input signal and the listening mode, the Virtual Surround Back mode may not be effective.  
32  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other connections  
08  
Chapter 8  
Other connections  
Connecting an analog audio component  
You can use the ANALOG AUDIO IN jacks to connect an  
analog audio component, such as a tape player.  
Important  
• When making or changing connections on the side  
panel of this unit, be sure to switch power off and  
disconnect the power cord from the wall socket.  
After completing all connections, connect the power  
cord to the wall socket.  
Receiver subwoofer  
Connecting auxiliary components  
Side panel  
You can connect both analog and digital external audio  
sources to this system. Digital audio sources include  
digital satellite receivers, CD recorders, etc.  
L
R
We recommend using an HDMI cable to connect  
sources that have HDMI terminals. For more information  
see Connecting using HDMI on page 35.  
ANALOG  
AUDIO IN  
To listen to audio from a TV, connect the TV’s audio cable  
to one of the inputs on this unit.  
From Audio output  
Tape player, MD, DAT, etc.  
Connecting for digital audio  
This system has optical-type digital inputs. Use these to  
connect external components, such as your MD or CD  
recorder.  
You can use the F.AUDIO input jack on the display unit  
to easily playback audio from a digital audio player or PC.  
Use a stereo mini-plug cable to connect a source to the  
display unit.  
Receiver subwoofer  
• When you connect a cable to the F.AUDIO jack, this  
unit’s input automatically switches to Front Audio  
In  
.
Display unit  
Side panel  
DISPLAY UNIT  
iPod  
MCACC  
SYSTEM  
F.AUDIO  
SETUP MIC  
IN  
1
IN  
2
OPTICAL  
DIGITAL  
F.AUDIO  
From digital audio  
output (optical)  
From analog  
audio output  
MD, CD Recorder, etc.  
Connect the OPTICAL IN 2 jack on the side panel to  
Stereo mini-plug cable  
Digital audio player, etc.  
the optical output of an external playback component.  
These include digital components such as an MD player,  
digital satellite, or a game system.  
You can also use the OPTICAL IN 1 jack to connect  
external components when not using it for sound input  
from a TV.  
33  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other connections  
08  
Connecting an iPod  
You can use the iPod jack on the display unit to playback  
music from an iPod. All operations can be carried out via  
the iPod. Use the supplied iPod cable to connect an iPod  
to this unit.  
Listening to an external audio source  
To listen to audio from a connected external component  
on this unit, choose its input function on the remote  
control. Some Pioneer products can be controlled via this  
remote.  
• When you connect an iPod, this unit’s input  
automatically switches to iPod.  
1
If the system isn’t already on, press RECEIVER  
• Certain iPod models have connectors that are not  
compatible with this unit.  
to switch on.  
Also make sure that the external source (TV, satellite  
receiver, etc.) is switched on.  
Display unit  
LINE  
2
Select an audio input source.  
DISPLAY UNIT  
Input sources are cycled through as shown below:  
iPod  
MCACC  
SETUP MIC  
SYSTEM  
F.AUDIO  
Digital 1  
Digital 2  
Analog  
iPod  
Front Audio In  
iPod  
The LCD screen changes to that of the selected input  
source.  
3
Press the button for the appropriate connected  
component.  
When a connected component is not displayed on the  
screen, or when you have connected a component not  
manufactured by Pioneer, press RCV button to put the  
remote control on the receiver subwoofer operation  
screen.  
iPod R  
iPod cable  
iPod  
Music  
>
Extras  
Settings  
>
>
Shuffle Songs  
Backlight  
4
If necessary, start playback of the external source.  
MENU  
®
iPod is a trademark of Apple Inc., registered in the U.S.  
and other countries.  
34  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other connections  
08  
Connecting external antennas  
About control out connections  
For an external AM antenna, use 5 to 6 meters of vinyl-  
insulated wire and set up either indoors or outdoors.  
Leave the loop antenna connected.  
Many Pioneer components support CONTROL  
connections, by which you can use the remote controls  
of any connected components by aiming them at the  
sensor of just one component.  
For an external FM antenna, use a PAL connector to hook  
up an external FM antenna.  
When you use a remote control, the control signal is  
passed along the chain to the appropriate component.  
external FM antenna  
If you choose to use this feature, you must make sure that  
you also have at least one set of HDMI or analog audio  
jacks connected to another component for grounding  
purposes.  
Receiver subwoofer  
Using the supplied control cable on either side,  
connect the CONTROL IN jack on another Pioneer  
component to the CONTROL OUT jack on the  
receiver subwoofer.  
Side panel  
This will allow you to control the other component by  
pointing its remote at the display unit supplied with this  
receiver subwoofer.  
ANTENNA  
AM LOOP  
FM  
UNBAL 75  
Connecting using HDMI  
AM Loop antenna  
If you have an HDMI or DVI (with HDCP) equipped  
component, you can connect it to this receiver using a  
external AM antenna  
1
PAL connector  
commercially available HDMI cable.  
The HDMI connection transfers uncompressed digital  
video, as well as almost every kind of digital audio that the  
connected component is compatible with, including  
DVD-Video, DVD-Audio, SACD, Blu-ray Disc, Video CD/  
Super VCD, CD and MP3, etc.  
Indoor antenna  
(vinyl-coated Wire)  
Outdoor antenna  
5 m to 6 m  
Receiver subwoofer  
HDMI  
T
IN 3  
IN 2  
IN 1  
HDMI  
OUT  
IN  
3
IN  
2
IN  
1
SYSTEM  
Rear panel  
From HDMI output  
HDMI/DVI-equipped component  
Note  
1 • An HDMI connection can only be made with DVI-equipped components compatible with both DVI and High Bandwidth Digital Content Protection  
(HDCP). If you choose to connect to a DVI connector, you will need a separate adaptor (DVIHDMI) to do so. A DVI connection, however, does not  
support audio signals. Consult your local audio dealer for more information.  
• This unit has been designed to be compliant with HDMI (High-Definition Multimedia Interface) Version 1.3a. Depending on the component you have  
connected, using a DVI connection may result in unreliable signal transfers. Also, when using a component with HDMI version 1.0, it is not possible to  
output copy-controlled DVD-Audio CPPM sources from the HDMI connection.  
• This unit supports SACD, Dolby Digital Plus, Dolby TrueHD and DTS-HD Master Audio. To take advantage of these formats, however, make sure that  
the component connected to this unit also supports the corresponding format.  
35  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Other connections  
08  
1
Use an HDMI cable to connect the HDMI IN 1 to 3  
ENTER  
interconnect on this receiver subwoofer to an HDMI  
output on your HDMI component.  
Once this receiver subwoofer is properly connected to  
your HDMI component, the HDMI indicator (red) lights  
up on the display unit when you watch HDMI contents.  
3
4
Select ‘HDMI Mode’, then press ENTER.  
Adjust the setting then press ENTER to  
ENTER  
confirm.  
2
Use an HDMI cable to connect the HDMI OUT  
AMP Mode – Output an HDMI audio signal from this  
unit.  
interconnect on this receiver subwoofer to an HDMI  
interconnect on a HDMI-compatible display.  
• The arrow on the cable connector body should be  
facing right for correct alignment with the connector  
on the player.  
Through Mode – Output an HDMI audio signal from  
a TV or plasma television.  
The HDMI THROUGH indicator lights.  
About HDMI  
HDMI (High-Definition Multimedia Interface) supports  
both video and audio on a single digital connection for  
use with DVD players, DTV, set-top boxes, and other AV  
devices. HDMI was developed to provide the  
technologies of High-bandwidth Digital Content  
Protection (HDCP) as well as Digital Visual Interface  
(DVI) in one specification. HDCP is used to protect digital  
content transmitted and received by DVI-compliant  
displays.  
3
Use the HDMI 1 to 3 button to select the HDMI input  
you’ve connected to (for example, HDMI 2).  
You can also use the display unit INPUT SELECTOR to  
carry out this operation.  
• Set the HDMI Mode in HDMI mode setting below to  
Through Mode if you want to hear HDMI audio  
output from your TV or plasma television (no sound  
will be heard from this receiver subwoofer).  
HDMI has the capability to support standard, enhanced,  
or high-definition video plus standard to multi-channel  
surround-sound audio. HDMI features include uncom-  
pressed digital video, a bandwidth of up to 2.2 gigabytes  
per second (with HDTV signals), one connector (instead  
of several cables and connectors), and communication  
between the AV source and AV devices such as DTVs.  
• If the video signal does not appear on your TV or  
plasma television, try adjusting the resolution  
settings on your component or display.  
HDMI mode setting  
HDMI, the HDMI logo and High-Definition Multimedia  
Interface are trademarks or registered trademarks of HDMI  
Licensing LLC.  
Specifies the routing of the HDMI audio signal out of this  
receiver subwoofer (amp) or through to a TV or plasma  
television. You cannot use a number of sound functions  
of this unit when HDMI Mode is set to Through Mode.  
Important  
RCV  
Press to set the remote control to receiver  
control mode in order to operate the receiver  
subwoofer (make sure that the LCD displays the  
RECEIVER screen).  
SETUP  
1
2
Press SETUP.  
ENTER  
Select ‘HDMI Setup’ then press ENTER.  
36  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HDMI Control  
09  
Chapter 9  
HDMI Control  
By connecting this unit to an HDMI Control-compatible  
Pioneer plasma television or the HDD/DVD recorder with  
an HDMI cable, you can control this unit from the remote  
control of a connected plasma television, as well as have  
the connected plasma television automatically change  
inputs in response to operations carried out on this unit.  
Making the HDMI Control connections  
You can use synchronized operation for a connected  
plasma television and up to three other components  
(including a maximum of two recorders or players).  
Be sure to connect the plasma television’s audio cable to  
the audio input of this unit.  
Refer to the operating instructions for your plasma  
television for more information about which operations  
can be carried out by connecting via HDMI cable.  
• If you use a commercially available HDMI cable,  
check whether the cable supports the HDMI 1.3  
standard. Otherwise, the HDMI Control function may  
not operate properly.  
• You cannot use this function with components that  
do not support HDMI Control.  
• We cannot guarantee this unit will work with HDMI  
Control-compatible components other than those  
made by Pioneer.  
HDMI Control-compatible  
From HDMI outut  
Important  
Pioneer HDD/DVD recorder,  
Blu-ray disc player or DVD player  
RCV  
Press to set the remote control to receiver  
control mode in order to operate the receiver  
subwoofer (make sure that the LCD displays the  
RECEIVER screen, as shown below).  
Receiver subwoofer  
Side panel  
Rear panel  
HDMI  
RECEIVER  
OUT  
IN  
3
IN  
2
IN  
1
ANTENNA  
L
AM LOOP  
ADV  
F.S.  
IN  
1
IN  
2
R
SURR  
OPTICAL  
DIGITAL  
SURR SURR  
FM  
UNBAL 75  
ANALOG  
AUDIO IN  
SYSTEM  
or  
From digital audio  
output (optical)  
From Audio output  
To HDMI input  
HDMI Control-compatible  
Pioneer plasma television  
37  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HDMI Control  
09  
• Connect the plasma television directly to this unit.  
Interrupting a direct connection with other amps or  
an AV converter (such as an HDMI switch) can cause  
operational errors.  
Important  
• When connecting this system or changing  
connections, be sure to switch the power off and  
disconnect the power cord from the wall socket.  
After completing all connections, connect the power  
cords to the wall socket.  
After connecting this unit to an AC outlet, a 15-second  
initialization process begins. You cannot carry out  
any operations during initialization. The HDMI  
indicator on the display unit blinks during  
initialization, and you can turn this unit on once it has  
stopped blinking.  
HDMI Control-compatible  
Pioneer plasma television  
HDMI input  
HDMI cable  
HDMI output  
Other amps  
• To get the most out of this function, we recommend  
that you connect your HDMI component not to a  
plasma television but rather directly to the HDMI  
terminal on this unit.  
or AV converter  
HDMI input  
HDMI cable  
HDMI OUT  
Setting the HDMI options  
You must adjust the settings of this unit as well as HDMI  
Control-compatible connected components in order to  
make use of the HDMI Control function. For more  
information see the operating instructions for each  
component.  
Receiver subwoofer  
• Only connect components you intend to use as a  
source to the HDMI input of this unit. Interrupting a  
direct connection with other amps or an AV converter  
(such as an HDMI switch) can cause operational errors.  
Setting the HDMI Control mode  
Choose whether to set this unit’s HDMI Control function  
On or Off. You will need to set it to Control On to use the  
HDMI Control function.  
• When using a TV not manufactured by Pioneer, put  
this setting to Control Off.  
HDMI Control-compatible  
Pioneer plasma television  
HDMI input  
SETUP  
1
2
3
4
Press SETUP.  
HDMI cable  
HDMI OUT  
ENTER  
ENTER  
ENTER  
Select ‘HDMI Setup’ then press ENTER.  
Select ‘HDMI Ctrl’, then press ENTER.  
Adjust the setting then press ENTER to  
Receiver subwoofer  
HDMI IN  
HDMI cable  
HDMI output  
confirm.  
Other amps or AV converter  
Control On – Enables the HDMI Control function.  
When this unit’s power is turned off and you have a  
supported source begin playback while using the  
HDMI Control function, the audio and video output  
from the HDMI connection are output from the  
plasma television.  
Control Off – The HDMI Control is disabled.  
Synchronized operations cannot be used. When this  
unit’s power is turned off, audio and video of sources  
connected via HDMI are not output.  
38  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HDMI Control  
09  
Setting the Auto Delay  
Important  
This feature automatically corrects the audio-to-video  
delay between components connected with an HDMI  
cable. The audio delay time is set depending on the  
operational status of the display connected with an  
HDMI cable. The audio delay time is automatically  
adjusted according to the video delay time.  
• You must set this setting to activate the HDMI Control  
function.  
Before using synchronization  
Once you have finished all connections and settings, you  
must:  
SETUP  
1
2
3
4
Press SETUP.  
1
Put all components into standby mode.  
ENTER  
ENTER  
ENTER  
Select ‘HDMI Setup’ then press ENTER.  
Select ‘Auto Delay’, then press ENTER.  
Select ‘A.Delay On’ or ‘A.Delay Off’ then  
2
Turn the power ON for all components, with the  
power for the plasma television being turned on  
last.  
3
Choose the HDMI input to which the TV is  
connected to this unit, and see if video output from  
connected components displays properly on the  
screen on not.  
press ENTER to confirm.  
Synchronized amp mode  
Tip  
Synchronized amp mode begins once you carry out an  
operation for the plasma television. For more  
information, see the operating instructions of your  
plasma television.  
• This feature is only available when the connected  
display supports the automatic audio/video  
synchronizing capability (‘lip-sync’) for HDMI or  
HDMI Control. If you find the automatically set delay  
time unsuitable, set A.Delay to Off and adjust the  
sound delay settings manually (page 27).  
Synchronized amp mode operations  
By connecting a component to this unit with an HDMI  
cable you can use synchronized amp mode, which allows  
you to synchronize the following operations:  
Audio input settings from plasma televisions  
(TV Input)  
• Displays on the plasma television when you mute or  
adjust the volume of this unit.  
To listen to audio from a plasma television on this device,  
you will need to connect an audio cable other than an  
HDMI cable. From this menu, set the audio input to that  
which you would like to connect. Press TV on the remote  
control to switch this unit to the input source selected  
here. This setting is changed to the selected input and  
the audio from the plasma television is output from this  
device.  
• The input of this unit is automatically changed when  
playback occurs on a connected component.  
• Even if you change this unit’s input to a device that is  
not connected by HDMI, the synchronized amp mode  
remains in effect.  
• By pressing GENRE when listening to a source from  
an HDD/DVD recorder, the most appropriate  
Select from inputs Digital 1, Digital 2 and Analog.  
listening mode is automatically selected (page 26).  
SETUP  
1
2
3
4
Press SETUP.  
Canceling synchronized amp mode  
ENTER  
ENTER  
ENTER  
If you cancel synchronized amp mode while connected  
via HDMI to a plasma television or while you are watching  
a TV programme, the power for this unit is turned off.  
Select ‘System Setup’ then press ENTER.  
Select ‘TV Input’, then press ENTER.  
Adjust the setting then press ENTER to  
confirm.  
39  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional information  
10  
Chapter 10  
Additional information  
Important  
Setting up the remote to control your TV  
RCV  
Press to set the remote control to receiver  
You can use the supplied remote to control your TV. To be  
able to use this feature you first have to program the  
remote with a maker code from the table on the following  
page.  
control mode in order to operate the receiver  
subwoofer (make sure that the LCD displays the  
RECEIVER screen, as shown below).  
TV  
1
2
Set the input to TV.  
RECEIVER  
Press and hold the TV button and press SETUP.  
The TV preset screen is shown on the remote control, and  
the current maker code is displayed on the LCD screen.  
ADV  
F.S.  
SURR  
SURR SURR  
TV PRESET  
Dimming the display  
3 5 1  
2
Maker code  
Number buttons  
ENTER  
You can choose to dim the display of the display unit if you  
1
3
1
find it too bright.  
4
7
5
6
9
SETUP  
1
2
3
4
Press SETUP.  
8
ENTER  
ENTER  
ENTER  
CLEAR  
ENTER  
0
Select ‘System Setup’ then press ENTER.  
Select ‘Dimmer’ then press ENTER.  
Select ‘Dimmer Light’ or ’Dimmer Dark’  
EXIT  
3
Use the number buttons to input the maker code  
for your TV, and press ENTER.  
See the table on the next page for the list of maker codes.  
If there is more than one code given for your make, input  
the first one in the list.  
then press ENTER to confirm.  
• If the maker’s name of your TV doesn’t appear in the  
table, you will not be able to use this remote to  
control your TV.  
Setting the sleep timer  
4
Point the remote towards your TV and press  
SOURCE to check that the remote works with your  
TV.  
If the remote is set up correctly, the TV should switch off.  
If it doesn’t and there is another code given for your  
maker, repeat step 1 with a new code.  
The sleep timer switches off the receiver subwoofer after  
a specified time so you can fall asleep without worrying  
about it.  
SLEEP  
Press to select an option.  
Choose between the following options:  
Sleep On – Switches off after about an hour  
Sleep Off – Cancels the sleep timer  
After selecting Sleep On, you can press SLEEP again to  
check how much time is left. Each line indicates  
approximately 12 minutes (remaining):  
S l e e p - - - - -  
Note  
1 The display of the display unit dims when the sleep timer is set, regardless of this setting.  
40  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional information  
TV Preset code list  
10  
Please note that there are cases where only certain functions may be controllable after assigning the proper preset code, or the  
codes for the manufacturer in the list will not work for the model that you are using.  
Manufacturer Code(s)  
Manufacturer Code(s)  
Admiral 003, 004, 005  
Aiwa 006, 007, 008  
Akai 009, 010  
Alba 011  
NEC 128, 129, 130, 131  
Nokia 086, 087, 132, 133, 134  
Nokia Oceanic 135, 136  
Nordmende 137, 138, 139  
AOC 012  
Okano 140  
Onwa 141  
Orion 142  
Bell&Howell 013, 014  
Bestar 015  
Blaupunkt 016, 017  
Blue sky 018  
Panasonic 143, 144, 145, 146, 147, 148, 149, 150  
Philco 151, 152, 153  
Brandt 019  
Philips 154, 155, 156  
Phonola 157  
Brocsonic 020, 021  
Bush 022  
Portland 158, 159  
Clatronic 023  
Proscan 160  
Craig 024, 025, 026, 027  
Croslex 028  
Quasar 161, 162  
Radio 163  
Curtis Mathis 029, 030, 031  
Radio Shack 164, 165, 166, 167  
Radiola 168  
Daewoo 032, 033, 034, 035, 036, 037  
Daytron 038  
Dual 039, 040  
RCA 169, 170, 171, 172, 173, 174, 175  
SABA 176, 177, 178, 179, 180  
Samsung 181, 182, 183, 184, 185, 186, 187, 188  
Sanyo 189, 190, 191, 192, 193, 194, 195, 196, 197, 198  
Schneider 199, 200, 201, 202  
Scott 203, 204  
Emerson 041, 042, 043, 044, 045, 046, 047  
Ferguson 048, 049, 050  
First line 051  
Fisher 052, 053  
Fraba 054  
Sharp 205, 206, 207, 208, 209, 210, 211  
Siemens 212  
Fujitsu General 055  
Funai 056, 057, 058, 059, 060  
Signature 213, 214  
Sony 215, 216  
GE 061, 062, 063, 064, 065  
Goldstar 066, 067, 068, 069, 070  
Goodmans 071, 072, 073  
Grundig 074, 075, 076  
Hitachi 077, 078, 079, 080, 081, 082  
HYUNDAI 083  
ICE 084  
Irradio 085  
Itt 086, 087  
JC Penny 088, 089, 090, 091  
JVC 092, 093, 094, 095, 096, 097  
Sylvania 217, 218, 219  
Symphonic 220  
Tatung 221  
Telefunken 222, 223, 224, 225  
Thomson 226, 227  
Thorn 228  
Toshiba 229, 230, 231, 232, 233, 234  
Universum 235  
Videch 236, 237, 238  
W.Whouse 239  
Wards 240, 241, 242, 243  
Watson 244  
Yamaha 245, 246, 247, 248, 249  
Zenith 250, 251  
PIONEER 001, 002  
Kendo 098  
KTV 099, 100, 101  
LG 102  
Loewe 103, 104, 105  
LXI 106, 107, 108, 109, 110, 111  
Magnavox 112, 113, 114, 115  
Mark 116  
Matsui 117, 118  
Medion 119  
Mitsubishi 120, 121, 122, 123, 124, 125, 126  
Mivar 127  
41  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional information  
Resetting the system  
10  
Surround sound formats  
Below is a brief description of the main surround sound  
formats you’ll find on DVDs, satellite, cable and terrestrial  
broadcasts, and video cassettes.  
Use this procedure to reset all system settings to the  
factory default.  
1
Switch the system on.  
Dolby  
2
Press and hold INPUT SELECTOR then press the  
STANDBY/ON button on the display unit.  
The next time you switch on, all the system settings  
should be reset.  
The Dolby technologies are explained below. See  
Installation and maintenance  
Dolby Digital  
Hints on installation  
Dolby Digital is a multichannel digital audio coding system  
widely used in cinemas, and in the home for DVD and digital  
broadcast soundtracks. It can deliver up to six discrete audio  
channels, comprising five full range channels and a special  
LFE (low frequency effects) channel used mainly for deep,  
rumbling sound effects; hence the term “5.1-channel” Dolby  
Digital.  
We want you to enjoy using this system for years to come,  
so please bear in mind the following points when  
choosing a location:  
Do...  
Use in a well-ventilated room.  
Place on a solid, flat, level surface, such as a table, shelf or  
stereo rack.  
In addition to the format features above, Dolby Digital  
decoders offer downmixing for compatibility with mono,  
stereo and Dolby Pro Logic audio from a number of bit rates  
and channels. Another feature, called Dialog Normalization,  
attenuates programs based on the average level of dialog in  
a program relative to its peak level (also known as Dialnorm)  
in order to achieve uniform playback level.  
Don’t...  
Use in a place exposed to high temperatures or humidity,  
including near radiators and other heat-generating  
appliances.  
Place on a window sill or other place where the system will  
be exposed to direct sunlight.  
Use in an excessively dusty or damp environment.  
Place directly on top of an amplifier, or other component in  
your stereo system that becomes hot in use.  
Use near a television or monitor as you may experience  
interference — especially if the television uses an indoor  
antenna.  
Dolby Pro Logic II and Dolby Surround  
Dolby Pro Logic IIx is an improved version of the Dolby Pro  
Logic II (and Dolby Pro Logic) decoding system. Using the  
innovative “steering logic” circuit, this system extracts  
surround sound from sources as follows:  
Use in a kitchen or other room where the system may be  
Dolby Pro Logic – 4.1 channel sound (mono surround)  
from any stereo source  
exposed to smoke or steam.  
Use on a thick rug or carpet, or cover with cloth — this may  
prevent proper cooling of the system unit.  
Place on an unstable surface, or one that is not large enough  
to support all four of the system unit’s feet.  
Dolby Pro Logic II – 5.1 channel sound (stereo  
surround) from any stereo source  
With two channel sources, the “.1” subwoofer channel is  
generated by bass management in the receiver.  
Dolby Surround is an encoding system which embeds  
surround sound information within a stereo soundtrack,  
which a Dolby Pro Logic decoder can then use for enhanced  
surround listening with greater sound detail.  
Dolby Digital Plus  
Dolby Digital Plus is the next-generation audio technology  
for all high-definition programming and media. It combines  
the efficiency to meet future broadcast demands with the  
power and flexibility to realize the full audio potential  
expected in the upcoming high-definition era. Built on Dolby  
Digital, the multi-channel audio standard for DVD and HD  
broadcasts worldwide, Dolby Digital Plus was designed for  
the next-generation A/V receivers but remains fully  
compatible with all current A/V receivers.  
42  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional information  
10  
Dolby Digital Plus delivers multi-channel audio programs of  
up to 7.1 channels (*) and supports multiple programs in a  
single encoded bitstream with the maximum bit rate  
potential of up to 6 Mbps and the maximum bit rate  
performance of up to 3 Mbps on HD DVD and 1.7 Mbps on  
Blu-ray Disc, and it outputs Dolby Digital bitstreams for  
playback on existing Dolby Digital systems. Dolby Digital  
Plus can accurately reproduce the sound originally intended  
by directors and producers.  
DTS-ES  
DTS-ES (the ES stands for Extended Surround) is a decoder  
that is capable of decoding both DTS-ES Discrete 6.1 and  
DTS-ES Matrix 6.1 encoded sources. DTS-ES Discrete 6.1  
gives ‘true’ 6.1 channel sound, with a completely separate  
(discrete) surround back channel. DTS-ES Matrix 6.1 has a  
surround back channel matrixed into the surround left/right  
channels. Both sources are also compatible with a  
conventional DTS 5.1 channel decoder.  
It also features multi-channel sound with discrete channel  
output, interactive mixing and streaming capability in  
advanced systems. Supported by High-Definition Media  
Interface (HDMI), a single-cable digital connection is  
possible for high-definition audio and video.  
DTS Neo:6  
DTS Neo:6 can generate 6.1 channel surround sound from  
any matrixed stereo source (such as video or TV) and from  
5.1 channel sources. It uses both the channel information  
already encoded into the source, as well as its own  
processing to determine channel localization (with two  
channel sources, the “.1” subwoofer channel is generated by  
bass management in the receiver). Two modes (Cinema and  
Music) are available using DTS Neo:6 with two channel  
sources.  
Dolby TrueHD  
Dolby TrueHD is the next-generation lossless encoding  
technology developed for high-definition optical discs in the  
upcoming era. Dolby TrueHD delivers tantalizing sound that  
is bit-for-bit identical to the studio master, unlocking the true  
high-definition entertainment experience on high-definition  
optical discs in the next generation. When coupled with  
high-definition video, Dolby TrueHD offers an  
DTS 96/24  
DTS 96/24 is an extension of the original DTS Digital  
Surround which offers high quality 96 kHz/24-bit audio using  
a DTS 96/24 decoder. This format is also fully backward  
compatible with all existing decoders. This means that DVD  
players can play this software using a conventional DTS 5.1  
channel decoder.  
unprecedented home theater experience with stunning  
sound and high-definition picture.  
It supports bit rates of up to 18 Mbps and records up to 8 full-  
range channels (*) individually with 24-bit/96 kHz audio. It  
also features extensive metadata including dialogue  
normalization and dynamic range control. Supported by  
High-Definition Media Interface (HDMI), a single-cable  
digital connection is possible for high-definition audio and  
video.  
DTS-EXPRESS  
DTS-EXPRESS is a low-bitrate encoding technology  
supporting up to 5.1 channels with fixed data transfer rates.  
This format is incorporated with sub audio on HD DVD and  
secondary audio on Blu-ray Disc while boasting the potential  
applicability to upcoming broadcasts and memory audio  
contents.  
* HD DVD and Blu-ray Disc standards currently limit their  
maximum number of audio channels to eight, whereas  
Dolby Digital Plus and Dolby TrueHD support more than  
eight audio channels.  
DTS-HD Master Audio  
DTS-HD Master Audio is a technology that delivers master  
audio sources recorded in a professional studio to listeners  
without any loss of data, preserving audio quality. DTS-HD  
Master Audio adopts variable data transfer rates, facilitating  
data transfer to the maximum rate of 24.5 Mbps in the  
Blu-ray disc format, 18.0 Mbps in the HD-DVD format, which  
by far exceeds that of a standard DVD. These high data  
transfer rates enable lossless transmission of 96 kHz/24-bit  
7.1-channel audio sources without deteriorating the quality  
of the original sound. DTS-HD Master Audio is an  
Manufactured under license from Dolby Laboratories. “Dolby”,  
“Pro Logic” and the double-D symbol are trademarks of Dolby  
Laboratories.  
DTS  
The DTS technologies are explained below. See  
irreplaceable technology that can reproduce sound faithfully  
as intended by the creator of music or movies.  
“DTS” is a registered trademark of DTS, Inc. and “DTS-HD  
Master Audio” is a trademark of DTS, Inc.  
DTS Digital Surround  
DTS Digital Surround is a 5.1-channel audio coding system  
from DTS Inc. now widely used for DVD-Video, DVD-Audio,  
5.1 music discs, digital broadcasts, and video games. It can  
deliver up to six discrete audio channels, comprising five full  
range channels, including an LFE channel. Higher sound  
quality is achieved through the use of a low compression  
rate, and high rates of transmittance during playback.  
43  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional information  
Troubleshooting  
10  
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with  
this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other  
components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks  
listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.  
• If the system does not operate normally due to external effects such as static electricity disconnect the plug from  
the outlet and insert again to return to normal operating conditions.  
• For audio-related problems, please also check the settings of the audio playback device. See the operating  
instructions for the device for detailed information.  
General  
Problem  
Remedy  
The power does not turn on, or • Leave the unit plugged in, wait for one minute, then switch back on.  
switches off suddenly (an error • Make sure there are no loose strands of wire touching the unit. This could cause the  
message may be displayed at system to shut off automatically.  
startup). Or, the display  
• Check that the speakers are connected correctly.  
disappears suddenly and no  
sound is output (with the  
POWER ON indicator (Blue)  
• Make sure there is enough space for ventilation around the receiver subwoofer.  
• Make sure the voltage of the mains power source is correct for the model.  
• Try reducing the volume level.  
and the HDMI indicator (Red) • If the problem persists, take it to your nearest Pioneer authorized service center or your  
lit up).  
dealer for servicing.  
• Do not block the air intake opening on the bottom as well as the air exhaust opening on  
the back of this unit.  
No sound is output when an  
input function is selected.  
• If you’re using the line input, make sure the component is connected correctly and the  
volume level of your external component (i.e. a portable player, etc.) is adjusted (see  
Connecting auxiliary components on page 33).  
• Turn up the volume.  
• No audio is output from the speakers connected to this unit if HDMI Mode is set to  
Through Mode (page 36).  
• No audio is output if a DVI component is connected via HDMI.  
• Press MUTE on the remote control to turn muting off.  
No sound from surround  
speaker.  
• Refer to Channel level setting on page 30 to check the speaker levels.  
• Check that you haven’t selected the Stereo mode (see Listening in surround sound on  
page 24).  
• Connect the speakers properly (refer to Connecting up on page 8).  
• Verify the audio output and HDMI settings of your external component when connecting  
an external component via an optical digital cable or HDMI cable.  
Can’t operate using the remote • Replace the batteries (Putting the batteries in the remote control on page 21).  
control.  
• Operate within 7 m, 30° of the remote sensor (Using the remote control on page 22).  
• Remove any obstacles or operate from another position.  
• Avoid exposing the remote sensor on the front panel to direct light.  
• For operating the other Pioneer component connected to the CONTROL OUT jack of this  
receiver subwoofer, make sure that the control cable and either an HDMI or analog audio  
cable are connected (page 35).  
44  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional information  
10  
Tuner  
Problem  
Remedy  
Considerable noise in radio  
broadcasts.  
• Connect the AM antenna (refer to Connecting up on page 8) and adjust the direction and  
position for best reception. You may also connect an additional internal or external AM  
antenna (refer to Connecting external antennas on page 35).  
• Fully extend the FM wire antenna, position for best reception, and secure to a wall. You  
may also connect an outdoor FM antenna (see Connecting external antennas on page 35).  
• Turn off other equipment that may be causing the noise or move it further away.  
• The tuning interval is incorrect for your country or region. See Changing the frequency  
step on page 29 to switch the tuning interval.  
Auto tuning does not pick up  
some stations.  
• The radio signal is weak. Auto tuning will only detect radio stations with a good signal.  
For more sensitive tuning, connect an outdoor antenna.  
HDMI  
Symptom  
Remedy  
No picture or sound.  
• This receiver is HDCP-compatible. Check that the components you are connecting are  
also HDCP-compatible.  
• Depending on the connected source component, it’s possible that it will not work with  
this receiver (even if it is HDCP-compatible).  
• If the problem still persists when connecting your HDMI component directly to your  
monitor, please consult the component or monitor manual or contact the manufacturer for  
support.  
No sound, or sound suddenly • Check that the HDMI Mode setting is set to AMP Mode/Through Mode.  
ceases.  
• If the component is a DVI device, use a separate connection for the audio.  
• Check the audio output settings of the source component.  
45  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional information  
Displayed Messages  
10  
Message  
Description  
192kHz PCM  
SACD  
These messages are displayed when you operate a function incompatible with the audio  
source being played back.  
DTS-HD  
DTS Express  
Dolby TrueHD  
Dolby D+  
No MIC  
Muting  
2ch Only  
Displays when you press MCACC when the MCACC setup mic is not connected.  
Displays when you press TEST TONE or MCACC while this unit is muted.  
An operation is prohibited because it is only applicable to 2 channel sources, while the  
current source is a multichannel source.  
Exit  
Appears when a menu is automatically exited after a set period of inactivity.  
HDMI Through  
Displays when you change the Listening Mode, the volume level, or some sound settings  
when the HDMI Mode is set to Through Mode.  
Unknown  
The genre information for contents being played back on the HDD/DVD recorder cannot be  
obtained.  
No Genre  
There is no genre set for contents being played back on the HDD/DVD recorder.  
The connected component is not compatible with synchronized genre mode.  
HDMI C.ERR 2C*  
Can’t use  
• You tried to use Genre Sync Mode for a source component that does not support this  
function.  
• The source component is in a situation where Genre Sync Mode cannot be used.  
• You tried to use Genre Sync Mode when the input source of this unit is a source other than  
HDMI.  
• The operation is forbidden due to the surround settings.  
• When the volume level is over 51, some functions are restricted.  
HDMI C.ERR 1**  
Check if the HDMI cable is properly connected. If the cable is properly connected, this unit  
may be damaged. In such an event, please contact a Pioneer-authorized service center or  
your nearest dealer.  
Noisy!  
Background noise is too high to complete MCACC setup successfully.  
Error MIC!  
An error occurred during MCACC setup because the microphone is not connected or is not  
connected properly.  
Error Speaker!  
Over Temp  
An error occurred during MCACC setup because the speakers are not connected or are not  
connected properly.  
Try lowering the volume. If this problem is not fixed by removing and inserting the power  
cable, this unit may be damaged. In such an event, please contact a Pioneer-authorized  
service center or your nearest dealer.  
OC Error1  
OC Error2  
Check whether the speaker cables are short-circuited. If the error message continues to be  
displayed, contact your Pioneer authorized service center or your dealer for servicing.  
*** BackUpERR  
Contact your Pioneer authorized service center or your dealer for servicing.  
46  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Additional information  
10  
SSP-LX70ST Satellite Speaker  
(Front/center speakers x2, Surround speakers x2)  
Specifications  
Front/center speakers  
Enclosure . . . . . . . . . . . . . . . . . . . . Closed-box bookshelf type  
(magnetically shielded)  
System . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 cm 1-way system  
Speakers. . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 cm cone type x3  
Impedance  
Front channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Center channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ω  
Frequency range . . . . . . . . . . . . . . . . . . . . . . 200 Hz to 20 kHz  
Maximum input power  
Front channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 W  
Center channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 W  
Dimensions . . . .122.5 mm (W) x 89.5 mm (H) x 104 mm (D)  
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 kg  
SX-LX70W Audio Multi-channel Receiver Subwoofer  
Amplifier section  
RMS Power Output (8 channel output):  
Front (L/R) . . . . . . . . . . . . . . . . . . . . . .100 W (50 W+ 50 W)  
(1 kHz, 10 % T.H.D., 8 )  
Dual Center (CL/CR). . . . . . . . . . . . . .100 W (50 W+ 50 W)  
(1 kHz, 10 % T.H.D., 8 )  
Surround (L/R) . . . . . . . . . . . . . . . . . .100 W (50 W+ 50 W)  
(1 kHz, 10 % T.H.D., 8 )  
Double Subwoofer (2 channel) . . . . .100 W (50 W+ 50 W)  
(100 Hz, 10 % T.H.D., 8 )  
FM tuner section  
Surround speakers  
Frequency range . . . . . . . . . . . . . . . . . . 87.5 MHz to 108 MHz  
Enclosure . . . . . . . . . . . . . . . . . . . . Closed-box bookshelf type  
(magnetically shielded)  
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 , unbalanced  
AM tuner section  
System . . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 cm 1-way system  
Speakers. . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 cm cone type x2  
Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ω  
Frequency range . . . . . . . . . . . . . . . . . . . . . . 200 Hz to 20 kHz  
Maximum input power . . . . . . . . . . . . . . . . . . . . . . . . . . .50 W  
Dimensions . . . .122.5 mm (W) x 89.5 mm (H) x 104 mm (D)  
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.44 kg  
Frequency range  
With 9 kHz step. . . . . . . . . . . . . . . . . . 531 kHz to 1602 kHz  
With 10 kHz step. . . . . . . . . . . . . . . . . 530 kHz to 1700 kHz  
Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Loop antenna  
Subwoofer section  
Enclosure. . . . . . . . . . . . . . . . . . . . . . . . .Bass-reflex floor type  
(magnetically shielded)  
Accessories  
System . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 cm 1-way system  
Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 cm cone type x2  
Impedance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Ω  
Frequency range . . . . . . . . . . . . . . . . . . . . . . 30 Hz to 500 Hz  
Maximum Input Power. . . . . . . . . . . . . . . . . . . . . . . . .50 W x2  
Accessory box (AS-LX70):  
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
AA/LR6 alkaline batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Power cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3  
Display unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
AM loop antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
FM wire antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
Microphone (for Auto MCACC setup) . . . . . . . . . . . . . . . . . . 1  
HDMI cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
Control cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
Display cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
Optical digital cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
iPod cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
This operating instructions  
Input/Output section  
HDMI terminal  
input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 pin x3  
output . . . . . . . . . . . . . . . . . . . . . . . . . 19 pin (5 V, 100 mA)  
Other connector  
System connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 pin  
Audio input . . . . . . . . . . . . . . . . . . . . . . .Optical x2 (Digital)  
RCA (2 pin) (Analog)  
Control output. . . . . . . . . . . . . . . . . . . . . . . . . . Mini jack x2  
Display unit  
System connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 pin  
Front Audio input . . . . . . . . . . . . . . . . . . . . . . . . . .Mini jack  
MCACC input . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Mini jack  
iPod input . . . . . . . . . . . . . . . . . . . . . 20 pin (12 V, 420 mA)  
Receiver subwoofer (SX-LX70W) box:  
Cleaning cloth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1  
Satellite Speakers (SSP-LX70ST) box:  
Speaker cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Speaker bases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Non-skid pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4  
Miscellaneous  
Power requirements. . . . . . . AC 110 V to 240 V, 50 Hz/60 Hz  
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 W  
Power consumption in standby  
. . . . . . . . . . . . . . . . . . . . . . . . . . . .0.39 W (HDMI Control ON)  
0.29 W (HDMI Control OFF)  
Note  
• Specifications and design subject to possible  
modification without notice, due to improvements.  
Dimensions . . . . . . 245 mm (W) x 409 mm (H) x 600 mm (D)  
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.8 kg  
Published by Pioneer Corporation.  
Copyright © 2007 Pioneer Corporation.  
All rights reserved.  
47  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
D3-4-2-1-7c_A_ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
目錄  
目錄  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
包裝箱內容物  
05 聆聽您的系統輸出的音效  
有效聲適用於最佳聲音. . . . . . . . . . . . . . . . . 24  
揚聲器設定指南  
01  
自動聆聽模式  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
設定時應注意的安全措施  
家庭劇院音效設定  
. . . . . . . . . . . . . . . . . . . . . . 6  
以環繞音效聆聽  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Dolby Pro Logic II Music 設定值 . . . . . . . . . . . . . . . 25  
中央影像設定  
. . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
標準環繞設. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
使先進環繞聲」功能  
前環繞設定  
準備揚聲器  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
. . . . . . . . . . . . . . . . . . . . 25  
使用前場前環繞聲模. . . . . . . . . . . . . . . . . . . . . . . 26  
以立體聲聆聽  
使用隨附的揚聲器支座. . . . . . . . . . . . . . . . . . . . . . . 6  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
類型同步化模式  
不使用隨附的揚聲器支座時  
揚聲器系統接線  
. . . . . . . . . . . . . . . . . . . 7  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
使聲音修正器」功能 . . . . . . . . . . . . . . . . . . . . 26  
效果聆聽  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
關於揚聲器擺設的其他注意事項. . . . . . . . . . . . . . . . . 7  
MCACC  
. . . . . . . . . . . . . . . . . . . . . . . . 27  
. . . . . 27  
調整低音及高音 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
調整聲音延遲  
接線  
02  
接收重低音揚聲器  
使午夜響度」寂靜」聆聽模式  
. . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
側面板  
後面板 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
顯示裝置背面  
06  
收聽廣播  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28  
收聽廣播  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
基本連接  
改善 FM 接收不良 . . . . . . . . . . . . . . . . . . . . . . . . . 28  
控制與顯示  
03  
改善  
音效不佳  
AM  
改變雜音抑制模式  
. . . . . . . . . . . . . . . . . . . . . . . . . 28  
. . . . . . . . . . . . . . . . . . . . . . . . . 28  
顯示裝置  
顯示幕  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
記憶電台 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
收聽預設電台  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
遙控器 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
操作接收重低音揚聲器  
操作內建的  
改變頻率間隔  
. . . . . . . . . . . . . . . . . . . . . . 15  
調諧器  
FM/AM  
. . . . . . . . . . . . . . . . . . . 16  
環繞音效設定值  
07  
操作先鋒電漿電視和一般電視機 . . . . . . . . . . . . . . 17  
使聲音設定」選單  
聲道位準設定值  
. . . . . . . . . . . . . . . . . . . . . . 30  
操作先鋒  
操作先鋒  
播放機  
Blu-ray Disc  
DVD  
. . . . . . . . . . . . . . . . . 18  
. . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
播放器  
. . . . . . . . . . . . . . . . . . . . . . . 19  
揚聲器距離設. . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
動態範圍控制  
操作先鋒硬/DVD 錄影機 . . . . . . . . . . . . . . . . . . 20  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
雙單聲道設定值  
裝入遙控器電池  
使用遙控器  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
. . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
使用虛擬後環繞模式 . . . . . . . . . . . . . . . . . . . . . . . 32  
衰減  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
操作遙控. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
使用液晶觸控畫面  
LFE  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32  
. . . . . . . . . . . . . . . . . . . . . . . . . 22  
使用測試音調整聲道位準  
. . . . . . . . . . . . . . . . . . . . . 32  
04  
開始操作  
08 其他接線  
使MCACC」設定以達最佳環繞音. . . . . 23  
連接輔助設備  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
數位音訊的連接  
. . . . . . . . . . . . . . . . . . . . . . . . . . . 33  
連接類比音效設備 . . . . . . . . . . . . . . . . . . . . . . . . . 33  
連接  
iPod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34  
聆聽外接音訊來源  
. . . . . . . . . . . . . . . . . . . . . . . . . . 34  
連接外接天. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
關於控制輸出連接  
. . . . . . . . . . . . . . . . . . . . . . . . . . 35  
連接  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
使用  
HDMI  
HDMI 模式設定 . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
關於  
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36  
4
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
目錄  
09 HDMI Control  
10 其他資訊  
HDMI Control  
. . . . . . . . . . . . . . . . . . . . . . 37  
連接  
進行  
調暗顯示幕亮度. . . . . . . . . . . . . . . . . . . . . . . . . . . . 40  
HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38  
設定睡眠定時器  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 40  
設定  
模式  
HDMI Control  
. . . . . . . . . . . . . . . . . . . . 38  
設定遙控器以控制電視機  
. . . . . . . . . . . . . . . . . . . . . 40  
電視機預設代碼. . . . . . . . . . . . . . . . . . . . . . . . . . 41  
重設系統  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
設定自動延遲  
電漿電視的音訊輸入設TV 輸入). . . . . . . . . . 39  
使用同步化之前  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
安裝與維護  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 39  
. . . . . . . . . . . . . . . . . . . . . . . . . . 39  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
安裝提. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
環繞音效格式  
同步化擴大器模式  
同步化擴大器模式操作 . . . . . . . . . . . . . . . . . . . . . 39  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
取消同步化擴大器模式  
. . . . . . . . . . . . . . . . . . . . . 39  
Dolby. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42  
DTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43  
故障排除 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
一般  
調諧器  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
HDMI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
顯示的訊息 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46  
規格  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
包裝箱內容物  
請確認包裝箱內有下列項目的物品。  
配件:  
遙控15 頁)  
接收重低音揚聲包裝箱:  
SX-LX70W  
清潔布  
AS-LX70  
AA/LR6 鹼性電x4 21 頁)  
電源線 (第  
x3  
頁)  
頁)  
12  
13  
揚聲SSP-LX70ST)包裝箱:  
揚聲前置/中置 、環繞  , 頁)  
x2 x2 11  
6
顯示裝第  
揚聲器連接線  
(第  
頁)  
11  
x6  
迴路天第  
線型天第  
頁)  
頁)  
AM  
FM  
11  
11  
揚聲器支座 (第 頁)  
x4  
6
防滑墊  
(第 , 頁)  
6
x16  
7
麥克用於自MCACC 設定23 頁)  
x4 7 頁)  
HDMI 連接線  
控制連接第  
顯示連接第  
頁)  
頁)  
35  
11  
光學數位連接第  
頁)  
12  
連接第  
頁)  
iPod  
34  
本操作手冊  
5
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
01  
揚聲器設定指南  
第 章  
1
揚聲器設定指南  
前環繞設定  
設定時應注意的安全措施  
此設定方式最適合在無法放置後環繞的情況下,或者不  
希望在聆聽區域內擺設過長的揚聲器電線時使用。使用  
組裝揚聲器時,請將揚聲器平放以免發生意外或受傷。  
請務必在平穩的表面上進行揚聲器的組裝、設定與擺  
放。  
此設定結合在第  
頁中的前場前環繞聲模式。  
26  
環繞聲(左側)  
前置/中置  
(左側)  
環繞聲(右側)  
前置/中置  
(右側)  
家庭劇院音效設定  
您可視房間大小與特性,決定使用這套系統中適用的揚  
聲器安置方式。  
接收重低音  
標準環繞設定  
聽位置  
此為標準多聲道環繞音效揚聲器設定,適用5.1 聲道  
的家庭劇院音效。  
前置/中置(左側)  
前置/中置(右側)  
準備揚聲器  
本機隨附的揚聲器支座可用於針對在房間內的擺放位置  
而進行調整。  
接收重低音  
聽位置  
使用隨附的揚聲器支座  
1 如下圖所示,將防滑墊貼在揚聲器支座上。  
請使用防滑墊有黏性的一邊貼上每個揚聲器支座的底  
部。  
環繞聲(左側)  
環繞聲(右側)  
防滑x 16  
每個揚聲器支座  
6
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
01  
揚聲器設定指南  
2
將揚聲器放在隨附的揚聲器支座上,然後使用隨附的螺  
裝上揚聲器支座。  
揚聲器系統接線  
絲將支座固定。  
請參閱以便正確連接揚聲器。完成接線後,請依照  
上圖所示安置揚聲器,以達最佳環繞音效。安置揚聲器  
後,請執行自MCACC 23 完成環繞  
音效的設定。  
隨附的揚聲器支座有兩種形狀。您可以在將揚聲器  
放在支座上後,檢查螺絲的位置是否正確對齊來判  
斷是否使用正確的揚聲器支座。 (前置/中置  
(左側)和環繞聲揚聲右側前置/中置  
(右側)和環繞聲揚聲左側)使用特定的支座,  
並隨附每個揚聲器的兩種類型支座。)  
關於揚聲器擺設的其他注意事項  
將主要前左右揚聲器安裝在與電視機等距之處。  
揚聲器  
使用標準環繞設定時,請將環繞揚聲器安裝在稍微  
高於耳朵的位置以得到最佳效果。  
使用前環繞設定時,使左側與右側揚聲器距離約  
1.5 m 以得到最佳效果。  
螺絲  
安全須知:  
請勿將揚聲器放置於不穩定的平面上,這樣可能導  
致揚聲器傾倒,造成揚聲器損壞或人員受傷。  
揚聲器支座  
本系統隨附的所有揚聲器都是防磁揚聲器。然而,  
視安裝位置不同,若揚聲器安裝位置過於接近電視  
機螢幕,則可能會發生色彩失真的情況。若發生此  
不使用隨附的揚聲器支座時  
將防滑墊黏貼於每個前置/中置與環繞揚聲器的底  
如圖所示。  
請使用防滑墊有黏性的一邊貼上每個揚聲器的底部。  
情況,請先關閉電視機電源, 分鐘至  
15  
分鐘後  
30  
再重新開機。若情況仍未改善,請將揚聲器系統遠  
離電視機。  
為安全起見,請確定揚聲器端子外沒有任何未包覆  
的揚聲器電線。  
請勿將隨附的揚聲器連接其他擴大器。否則可能造  
成故障或引起火災。  
請勿連接此系統外的其他揚聲器。  
揚聲器系統護網蓋無法取下。請勿試圖強行取下它,  
否則可能導致護網蓋損壞。  
防滑x 16  
前置/中置與環繞揚聲器  
請使用隨附的清潔布清潔音箱。請勿讓酒精、稀釋  
劑、甲苯或殺蟲劑接觸到本機表面,否則表面可能  
會變色。此外,使用沾有化學藥劑的清潔布時,請  
小心遵守其注意事項。  
7
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
02  
接線  
第 章  
2
接線  
接收重低音揚聲器  
側面板  
ANTENNA  
AM LOOP  
L
R
R
L
L
R
L
OUT  
1
OUT  
2
IN  
1
IN  
2
R
AC IN  
FRONT  
CENTER  
FRONT  
SURROUND  
SUBWOOFER  
CONTROL  
OPTICAL  
DIGITAL  
FM  
(
)
SPEAKERS 8 Ω  
UNBAL 75 Ω  
ANALOG  
AUDIO IN  
1
2
3
4
5
6
7
側面板的接頭上有蓋子。  
A. 接線時,拉起鉤子,然後取下蓋子。  
1
CONTROL OUT x2)  
使用隨附的控制連接線連接其他先鋒設備。  
B. 完成接線時,對準三個位置,然後將蓋子放回原  
始位置。  
( )  
DIGITAL OPTICAL IN x2  
要收聽光學數位音效,請將輸入變更Digital 1 或  
2
Digital 2。  
B
當您的電視機的數位輸出插孔連接到這些插孔時,設定  
請參閱第  
。  
39  
TV Input  
天線端子  
3
AM LOOP  
4
FM 天線插座  
A
5
ANALOG AUDIO IN 插孔  
使用立體聲音效代碼處理來自外部設備的聲音。若要收  
聽類比音效,請將輸入變更Analog。  
當您的電視機的類比輸出插孔連接到這些插孔時,設定  
TV Input請參閱第 39 。  
端子  
比對揚聲器連接線的顏色與各自的接頭顏色。  
6
SPEAKERS  
-電源插孔  
AC IN  
7
8
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
02  
接線  
後面板  
接頭  
端子的電視機。  
8
連接至有  
HDMI OUT  
HDMI  
9
HDMI IN 接頭 (x3)  
HDMI  
OUT  
IN  
3
IN  
2
IN  
1
使用高品質音訊/視訊連接方式連接相容的  
。  
HDMI  
若要選擇此輸入,請選HDMI 1 HDMI 3。  
10 SYSTEM  
SYSTEM  
接頭  
連接至顯示裝置。  
HDMI  
OUT  
IN 3  
IN 2  
IN 1  
SYSTEM  
8
9
10  
顯示裝置背面  
接頭  
1
連接至接收重低音揚聲器  
SYSTEM  
DISPLAY UNIT  
輸入插孔  
2
F.AUDIO  
若要聆聽來自外部設備的音效,請使用立體聲迷你插頭  
連接線連連接後,輸入自動變更為  
iPod  
MCACC  
SYSTEM  
F.AUDIO  
SETUP MIC  
Front Audio In  
輸入端子  
3
用於連接您的  
iPod  
1
2
3
4
做為音源。  
Apple iPod  
連接  
時,輸入自動變更為  
iPod  
iPod  
4
MCACC SETUP MIC 插孔  
用於連接供自MCACC 設定使用的隨附麥克風  
(請參閱第 23 。  
9
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
02  
接線  
基本連接  
顯示裝置  
SYSTEM  
接收重低音揚聲器  
HDMI  
OUT  
IN  
3
IN  
2
IN  
1
DISPLAY UNIT  
iPod  
MCACC  
F.AUDIO  
SETUP MIC  
SYSTEM  
INPUT  
後面板  
側面板  
ANTENNA  
1
L
AM LOOP  
R
R
L
L
R
L
SYSTEM  
R
FRONT  
CENTER  
FRONT  
SURROUND  
SUB  
顯示連接線  
ANALOG  
AUDIO IN  
4
2
3
CL  
FL  
FR  
CR  
AM迴路天線  
前置/  
中置揚聲器  
(左側)  
前置/  
中置揚聲器  
(右側)  
FM天線  
聆聽位置  
環繞聲  
揚聲器  
環繞聲  
揚聲器  
(左側)  
(右側)  
SL  
SR  
重要  
警告  
對此系統進行接線或變更接線時,請務必關閉電源,  
並將電源線插頭自牆上電源插座上拔除。完成所有  
接線後,再將電源線插頭接上電源插座。  
先鋒對於任何因錯誤組裝或安裝、牆壁固定強度不  
足、固定裝或其他建材不當使用或天災所  
造成之意外,概不負責。  
10  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
02  
接線  
1
將顯示幕連接線插入顯示裝置後方的接頭,然後將顯示  
4
連接顯示裝置與接收重低音揚聲器。  
連接所有揚聲器。  
每個揚聲器連接線的其中一端都有含顏色代碼的接  
頭,另一端則有兩條電線。  
SYSTEM  
幕連接線的另一端插入接收重低音揚聲器的  
接頭。  
顏色代碼線  
(連接至揚聲器)  
注意  
顏色代碼的接頭  
(連接至接收重低音揚聲器)  
請勿嘗試將顯示裝置安裝在牆上。  
2
AM  
迴路天線。  
組裝  
扭開並拉出每個電線的保護層。  
a
b
c
將電線連接至揚聲器上。使用後表面型號標籤上提  
供的顏色代碼指示可以識別圖中的每一個揚聲器。  
比對顏色代碼線與型號標籤上顏色指示,然後將  
a. 依箭頭指示方向彎曲支架。  
b. 將迴路天線夾在支架上。  
+
顏色代碼線插入紅端,另一條線插入  
若要固定在牆壁或其他表面上,先以螺絲固定支架  
後,再執行步驟 。  
c.  
端。  
b
(–)  
(+)  
紅色  
黑色  
我們建議您以螺絲固定支架前,先確認接收強度。  
顏色代碼線  
1
連接  
天線 。  
3
AM  
FM  
迴路天線的其中一條電線連接到每個  
天線  
AM  
a. AM  
2
端子上 。  
按下卡舌便可開啟端子,開啟後插入電線,鬆開卡  
舌便可將電線夾住固定。  
2
3
1
將另一端接上接收重低音揚聲器側面有顏色代碼的  
揚聲器端子。請確定將電線完全插入。  
請小心插入揚聲器插頭,因此在插入其中一個端子  
時必須朝正確方向插入。請確定接線正確。  
3
b. FM  
天線 插頭推入  
天線插槽的中央接腳。  
FM  
附註  
1 •  
請將天線遠離其他連接線、顯示裝置以及接收重低音揚聲器。  
28 FM  
AM  
35  
音效不佳,或第 頁上的連接外接天。  
若隨附天線的接收訊號不良,請參第  
頁上的改善  
接收不良改善  
不可安裝隨附的迴路天線以外的天線,或35 頁所述的外接天線。  
2 •  
請勿使天線接觸金屬物體,並避免將其安置在電腦、電視機或其他電器用品附近。  
若無線電收訊不良,可重新將每個天線電線裝至相反的端子以求改善。  
為達最佳收訊,請勿將 AM 迴路天線電線朝反方向扭開,或將其繞在迴路天線周圍。  
FM  
3
為確保最佳收訊,請確定  
天線完全展開,且未纏繞或懸掛於裝置後方。  
11  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
02  
接線  
後面板  
側面板  
HDMI  
OUT  
IN 3  
IN 2  
IN 1  
ANTENNA  
AM LOOP  
L
IN  
1
IN  
2
R
OPTICAL  
DIGITAL  
ANALOG  
AUDIO IN  
SYSTEM  
接收重低音揚聲器  
6
7
從數位音訊  
從音訊輸出  
輸出(光學)  
HDMI輸入  
電視機  
將電視機的音訊連接線連接至接收重低音揚聲器。  
若要使用本機聆聽電視機的聲音,您必須將電視機  
的音訊輸出插孔連接至本機的音訊輸入插孔。您可  
以使用數光學)或類比音訊連接線連接。如要  
聆聽數位音效,請連接至接收重低音揚聲器上的  
7
注意  
這些揚聲器端子均帶有危險電壓。為避免在連接或  
脫離揚聲器線時發生電擊危險,在觸摸任何未絕緣  
部分之前,請先將電源線插頭拔離。  
。若要在連接至支援的先鋒  
DIGITAL OPTICAL IN 1  
請勿連接此系統外的其他揚聲器。  
電漿電視時使用  
連接。  
功能,您必須透過  
HDMI Control  
請勿將隨附的揚聲器連接此系統以外的擴大器。若  
連接其他擴大器可能導致故障或引起火災。  
HDMI  
您必須先設「  
」以切換來自電漿電視  
TV Input  
連接插頭後,輕輕拉動連接線,以確定連接線的線  
端已經與端子牢牢地連接。連接不良可能產生噪音  
並造成聲音中斷。  
(具有  
功能)的音訊,或將本機的輸  
HDMI Control  
入來源切換至電視機音訊,然後使用隨附的遙控器  
操作您的電視機。如需詳細資訊,請參閱第 頁上  
17  
頁上的電  
如果纜線的芯線意外被拉出端子外並導致芯線互相  
接觸,將會對放大器產生過量的額外負載。這樣可  
能造成放大器停止作用,甚至損壞放大器。  
操作先鋒電漿電視和一般電視和第  
39  
漿電視的音訊輸入設。  
TV  
2
接上電源線。  
8
1
若有其他要連接的  
播放器或影音來源 設備,  
將電源線連接至接收重低音揚聲器的 電源插孔。  
AC  
依下列順序將每條電源線連接至牆上電源插座。  
5
DVD  
請先進行連接,稍後再插上電源。  
關於連接數位來源設備的方式,請參閱第  
頁。  
33  
接收重低音揚聲器  
電視機  
1.  
2.  
6 將重低音揚聲器連接至電視機。  
將接收重低音揚聲器HDMI OUT 插孔連接至電視  
將連接至接收重低音揚聲器側面板的電源線繞過本  
機背面,然後更換側面板的蓋子。  
HDMI 輸入插孔。  
附註  
1 請務必連接電視機或顯示器 (若有視訊來源),以便發揮此系統的家庭劇院功能。請參閱電視機或顯示器隨附的操作手冊,以了解連接的詳細資訊。  
2 •  
請勿使用本系統隨附以外的其他電源線。  
除連接本系統外,請勿將隨附的電源線作為其他用途使用。  
將本機連接至 AC 電源插座後,開15 秒的初始化程序。初始化期間不可以執行任何操作示裝置上HDMI 指示燈在初始化期間閃爍,您可  
HDMI  
以在此  
指示燈一停止閃爍時即開啟本機電源。  
12  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
03  
控制與顯示  
第 章  
3
控制與顯示  
顯示裝置  
1
2
3
頂部按鈕  
4
5
6
7
1 STANDBY/ON  
按下可開啟接收重低音揚聲器電源或切換至待機狀態。  
(第 頁)  
2
反覆按下可選擇其中一個外部音訊輸入插(  
INPUT SELECTOR  
33  
HDMI 1  
HDMI 3 Digital 1 Digital 2 Analog iPod  
)。  
Front Audio In  
按鍵  
3
用於調整音量。  
VOL +/–  
4
POWER ON 指示藍色)  
5 前面板顯示  
詳情請參閱14 頁。  
紅外線遙控感應(第  
頁)  
22  
6
7
指示紅色)  
HDMI  
當此接收重低音揚聲器連接至  
時指示燈會亮起。  
)相容設備  
HDMI HDCP  
在將本機電源插頭插入  
示燈也會亮起。  
電源插座後的初始化期間指  
AC  
13  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
03  
控制與顯示  
顯示幕  
1
2
3
4
5
6
7
DIRECT STEREO F.S.SURR.  
ADV.SURR. PRO LOGIC  
LOUDNESS MIDNIGHT DNR DIALOG HDMI THROUGH  
QUIET TONE S.RTRV MCACC  
2
DIGITAL  
2
DTS 96/24  
DSD PCM  
8
9
10 11  
1
DIRECT  
選擇直接聲音即關閉有效聲音時)指示燈會亮起  
24  
8 數位格式指示燈  
2DIGITAL  
(第  
。  
播放  
來源時指示燈會亮起(第  
。  
24  
Dolby Digital  
聆聽模式指示燈  
2
DTS  
DTS 來源時指示燈會亮24 。  
STEREO  
選擇立體聲模式或自動聆聽」模式中播放立體  
聲音源時指示燈會亮26 。  
DTS 96/24  
DTS 96/24 解碼時指示燈會亮24 。  
F.S.SURR.  
選擇其中一種前場前環繞聲聆聽模式時指示燈會亮  
26 。  
DSDPCM  
Direct Stream Digital  
時指示燈會亮起。  
,直接流數  
SACD  
位)轉換為  
DSD  
PCM  
ADV.SURR.  
選擇其中一種先進環繞聲聆聽模式時指示燈會亮起  
25 。  
PCM  
播放  
訊號時指示燈會亮起。  
PCM  
字元顯示幕  
9
3 2PRO LOGIC II  
10 調諧器指示燈  
Dolby Pro Logic II 解碼時指示燈會亮25 。  
聲音處理指示燈  
4
在選響度午夜寂靜」或音調控制功能時  
接收廣播時指示燈會亮起。  
指示燈會亮27 。  
在自動立體聲模式中接收立體FM 廣播時指示燈會  
亮起。  
5
S.RTRV  
聲音修正器啟動時指示燈會亮第  
。  
26  
6
HDMI THROUGH  
選擇  
單聲道接收時指示燈會亮起。  
FM  
HDMI Mode 設定為 Through Mode 時指示燈會亮起。  
7
MCACC  
特效開啟時指示燈會亮第  
11  
睡眠定時器啟動時指示燈會亮40 。  
。  
MCACC  
27  
。  
23  
自動  
設定期間會閃第  
MCACC  
14  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
03  
控制與顯示  
1
將接收重低音揚聲器切換開啟/待機。  
RECEIVER  
遙控器  
2
TV  
如需使用遙控器的詳細資訊,請參閱22 頁上的操  
作遙控器。  
將電視機電源切換開啟/待機。  
TV CTRL  
將遙控器切換至電視機操作模不會影響本機的  
目前輸入來源。  
操作接收重低音揚聲器  
本節說明如何操作接收重低音揚聲器的遙控器。請注  
意,當您為各個連接的裝置選擇輸入功能時,控制按鍵  
會有所不同。  
3
SOURCE  
將所選擇設備的電源切換開啟/待機22 。  
輸入選擇按鍵  
4
變更本機的輸入。使用本遙控器操作另一個連接設備  
時,必須按下這些按鍵的其中之一。  
2
RECEIVER  
SOURCE  
TV  
HDMI 1  
HDMI 3  
1
4
3
CTRL  
3
將輸入HDMI 1 切換HDMI 3。  
HDMI  
2
1
TV  
TV  
切換至在電視機輸入設定選擇的輸第  
。  
39  
FM/AM  
LINE  
(第  
頁)  
28  
FM/AM  
FM AM 波段。  
LINE 34 頁)  
反覆按下可選擇其中一個接收重低音揚聲器的音訊  
Digital 1Digital 2AnalogiPod 或  
Front Audio In。  
液晶觸控畫面  
5
5
顯示用於控制接收重低音揚聲器、電漿電視、  
DVD  
播放  
器、Blu-ray Disc 播放機和硬/DVD 錄影機等外部設備  
的按鍵。目前的操作模式顯示在遙控器螢幕的最上方。  
雖然液晶觸控畫面在一段時間未執行任何操作後會消  
失,但只要碰觸螢幕或按下遙控器上的按鍵時,它就會  
出現。  
其他設備按鍵  
用於操作硬碟  
6
錄影機或其他連接的設備。  
/DVD  
ꢀ/ꢁ/ꢂ/ꢃ (游標按鍵)ENTER  
用於控制接收重低音揚聲器功能。  
SETUP  
PAGE  
TOP MENU  
MENU  
7
6
DISC  
NAVIGATOR  
8
7
8
用於存取環繞聲設定、調諧器設定等的選單系統  
(第 、 、 、 頁。  
HOME  
MENU  
28 30 38 40  
RETURN  
SETUP  
9
6
9 RETURN  
用於取消設定。  
RECEIVER  
VOL  
10 RCV  
用於當本機在其他操作模式時切換至接收重低音揚聲  
器。再按一次可返回之前的操作模式。  
RCV  
MUTE  
12  
10  
11  
11 VOL +/–  
用於調整接收重低音揚聲器的音量。  
12 MUTE  
靜音或恢復播放已靜音的聲調整音量也使聲音恢復  
播放。  
15  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
03  
控制與顯示  
液晶觸控畫面  
FM/AM  
操作內建的  
調諧器  
TOP MENU  
MENU  
RECEIVER  
ADV.  
DISC  
F.S.  
NAVIGATOR  
13  
SURR  
SURR SURR  
1
2
HOME  
MENU  
RETURN  
SETUP  
3
SOUND  
DIRECT  
RTRV  
14  
15  
GENRE  
16  
1
ꢀ/ꢁ/ꢂ/ꢃ (游標按鍵)ENTER  
18  
19  
用於控制 調諧器功能。  
FM/AM  
SETUP  
用於存取選單系統或調諧器設定。  
RETURN  
TEST  
SOUND  
TONE  
MCACC  
SLEEP  
17  
20  
2
21  
EXIT  
3
用於取消設定。  
13 SURR  
用於選擇環繞聲模第  
。  
24  
液晶觸控畫面  
ADV.SURR  
用於將音訊設定變更為先鋒原始的先進環繞聲模式  
FM/AM  
25 。  
1
4
7
2
3
6
F.S.SURR  
26  
用於選擇前場前環繞聲模第  
14 GENRE  
用於類型同步化」模式中聆聽音第  
。  
5
8
4
9
。  
26  
(此按鍵僅在操作硬碟  
畫面時顯示。)  
錄影機期間出現  
RECEIVER  
/DVD  
CLEAR  
0
TUNE  
5
6
-
-
+
+
15 SOUND RTRV  
按下可將CD品質音效恢復成壓縮的音效來26。  
ST  
16 DIRECT  
用於開啟/關閉有效聲音模24 。  
4 數字按鍵  
17 MCACC  
用於直接選擇預設廣播電台。  
開始自動  
第  
。  
23  
MCACC  
CLEAR  
按下可清除任何輸入的內容並重新輸入。  
18 TEST TONE  
用於輸出測試以便進行揚聲器設定第  
。  
32  
5 TUNE +/–  
用於搜尋電台頻率。  
19 SOUND  
按下可進入音效選單,進而調整低音與高音等。  
6 ST +/–  
用於選擇預設電台。  
20 SLEEP  
按下可設定睡眠定時40 。  
21 EXIT  
取消設定並退RECEIVER 畫面。  
16  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
03  
控制與顯示  
操作先鋒電漿電視和一般電視機  
40  
些電視機使用。  
請先參閱第  
頁上的設定遙控器以控制電視中有關設定電視機預設電台的資訊。請注意,有些按鍵無法搭配某  
TV  
1
2
3
RECEIVER  
SOURCE  
TV  
未設定為先鋒  
電漿電視時顯示。  
PDP  
1
3
2
CTRL  
1
4
7
2
3
6
5
8
8
9
PAGE  
9
TOP MENU  
MENU  
CH  
RTN  
CH  
ENTER  
DISC  
10  
12  
0
NAVIGATOR  
4
+
+
INPUT  
HOME  
MENU  
RETURN  
14  
11  
13  
SETUP  
P
TV VOL  
5
7
6
MUTE  
-
-
1
2
TV  
液晶觸控畫面  
數字按鍵  
選擇頻道。  
CH RTN  
將電視機電源切換開啟/待機。  
8
TV CTRL  
將遙控器切換至電視機操作模不會影響本機的  
目前輸入來源。  
9
回到前一個選擇的頻道。  
SOURCE  
10 CH ENTER  
播放所選擇的頻道號碼。  
將電視機的電源切換開啟/待機。  
3
切換液晶觸控畫面上的頁面。  
PAGE </>  
11 P +/–  
選擇頻道。  
(游標按鍵)和  
ENTER  
4
ꢀ/ꢁ/ꢂ/ꢃ  
12 INPUT  
選擇電視機的輸入來源。  
用於導覽所有螢幕功能選單。按ENTER 選擇目前反白  
的選項。  
13 MUTE  
靜音。  
5
HOME MENU  
HOME MENU 畫面。  
14 TV VOL +/–  
設定音量。  
6 RETURN  
回到前一個選單畫面。  
紅/綠/黃/藍)按鍵  
7
選擇頁面。  
17  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
03  
控制與顯示  
Blu-ray Disc  
操作先鋒  
播放機  
RECEIVER  
SOURCE  
TV  
BD 1/2  
BD 2/2  
1
CTRL  
9
1
4
2
3
6
5
8
0
2
13  
PAGE  
10  
11  
TOP MENU  
MENU  
7
9
3
5
4
7
DISC  
NAVIGATOR  
ꢈ/ꢉ  
ZOOM  
ꢊ/ꢋ  
DISP  
CLEAR  
ENTER  
HOME  
MENU  
PLAY  
MODE  
12  
DISP  
12  
RETURN  
14  
15  
SETUP  
6
8
VIDEO  
ADJ  
1
SOURCE  
10 播放控制按鍵  
Blu-ray Disc 播放機的電源切換開啟/待機。  
按下可開始或繼續播放。  
2
PAGE </>  
液晶觸控畫面顯示多個頁面時,切換頁面。  
按下可停止播您可以按 繼續播放。  
3
TOP MENU / DISC NAVIGATOR  
按下可顯示 碟片的最上層選單。  
BD-ROM  
DVD-R/-RW 時,按下可顯示/退出 「碟片導向。  
MENU  
BD-ROM:按下可顯示/隱藏彈出式選單。  
:按下可顯示碟片選如果有。  
DVD-Video  
按下可暫停播放,再按一次即可重新開始播放。  
ꢅ  
按下可開始倒退/快轉掃描。  
4
ꢆ ꢇ  
按下可跳到上一個/下一個章節/曲目。  
DVD-Video  
ꢀ/ꢁ/ꢂ/ꢃ  
(游標按鍵)和  
5
ENTER  
/ꢉ ꢊ/ꢋ  
用於導覽螢幕功能和選單。按下  
指令。  
選擇選項或執行  
ENTER  
用於慢動作格階梯式格放。  
11 ZOOM  
按下可在播放靜態影像時縮放畫面。  
6 HOME MENU  
按下可顯示播放器的  
,進入  
Home Menu  
Home Menu  
使用大部分的播放器功能。  
12 DISP  
按下可顯示資訊。  
7 RETURN  
按下可回到前一個畫面。  
數字按鍵  
13  
用於輸入標題、章節或曲目編號等。  
紅/綠/黃/藍)按鍵  
8
用於導覽  
選單。  
ENTER  
按下可選擇選項或執行指令。  
BD-ROM  
液晶觸控畫面  
(AUDIO)  
按下可選擇聲道或語言。  
CLEAR  
按下可清除輸入的數字等。  
9
14 PLAY MODE  
按下可切換播放模例如重播。  
(SUBTITLE)  
按下可選擇字幕的顯示。  
15 VIDEO ADJ  
按下可顯調整視訊」畫面。  
(ANGLE)  
播放  
影片的多角度場景時,  
DVD-Video  
BD-ROM  
按下可變更拍攝角度。  
18  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
03  
控制與顯示  
DVD  
操作先鋒  
播放器  
RECEIVER  
SOURCE  
TV  
DVD 1/2  
DVD 2/2  
1
CTRL  
8
9
1
4
2
3
6
9
ꢈ/  
ꢉꢄ  
ꢋ/  
ꢊꢅ  
12  
13  
5
8
2
PAGE  
7
TOP MENU  
MENU  
3
5
6
4
7
DISC  
NAVIGATOR  
ENTER  
CLEAR  
0
PLAY  
MODE  
HOME  
MENU  
ZOOM  
DISP  
11  
DISP  
11  
10  
RETURN  
SETUP  
1
SOURCE  
播放器的電源切換開啟/待機。  
9 播放控制按鍵  
DVD  
PAGE </>  
按下可開始或繼續播放。  
2
液晶觸控畫面顯示多個頁面時,切換頁面。  
按下可停止播您可以按 繼續播放。  
3
按下可顯示  
TOP MENU  
碟片的最上層選單。  
DVD-Video  
按下可暫停播放,再按一次即可重新開始播放。  
4
MENU  
DVD 碟片選單-本功能視碟片而異,而且可能顯示  
相同最上層選單。  
/ꢉ ꢄ /ꢊ ꢅ  
按下可開始倒退或快轉掃描。再按一次可變更速度。  
暫停時,按住可開始慢動作播放。反覆按可以變更  
播放速度。  
5
ꢀ/ꢁ/ꢂ/ꢃ (游標按鍵)ENTER  
在螢幕四周移動游標。按ENTER 選擇目前的選單選  
項。  
暫停時,按下可往前或往後移動一格。  
/ꢇ  
6 HOME MENU  
顯示/退出螢幕功能選單。  
按下可跳到上一個或下一個標題/章節/曲目/  
資料夾,或顯示上一個或下一個選單頁面。  
7 RETURN  
回到前一個顯示的選單畫面。  
10 ZOOM  
按下可在播放靜態影像時縮放畫面。  
11 DISP  
按下可顯示資訊。  
液晶觸控畫面  
8
(AUDIO)  
按下可選擇聲道或語言。  
數字按鍵  
12  
用於輸入標題、章節或曲目編號等。  
(SUBTITLE)  
按下可選擇字幕的顯示。  
ENTER  
按下可選擇選項或執行指令。  
(ANGLE)  
CLEAR  
按下可清除輸入的數字等。  
播放  
DVD-Video  
拍攝角度。  
影片的多角度場景時,按下可變更  
13 PLAY MODE  
按下可切換播放模例如重播。  
19  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
03  
控制與顯示  
/DVD  
操作先鋒硬碟  
錄影機  
RECEIVER  
SOURCE  
TV  
HDD/DVR 1/2  
HDD/DVR 2/2  
1
CTRL  
8
9
HDD  
DVD  
1
4
7
2
5
8
0
3
6
13  
14  
2
PAGE  
9
TOP MENU  
DISC  
MENU  
3
5
6
4
7
NAVIGATOR  
ꢊ/ꢋ  
CLEAR  
ꢈ/ꢉ  
15  
16  
CM  
BACK SKIP  
CM  
JUKE  
BOX  
+
HOME  
MENU  
11  
INPUT DISP  
10  
12  
RETURN  
SETUP  
CH  
STOP  
REC  
REC  
ì
17  
-
1
將硬碟  
SOURCE  
液晶觸控畫面  
錄影機的電源切換開啟/待機。  
/DVD  
8
HDD  
2
PAGE </>  
按下可選擇用於錄製和播放的硬碟。  
液晶觸控畫面顯示多個頁面時,切換頁面。  
DVD  
按下可選擇用於錄製和播放的  
DVD  
3
TOP MENU / DISC NAVIGATOR  
如果已載DVD-Video 或最終化DVD-R/-RW (視訊)  
碟片,按下可顯示最上層選單碟片導向」畫面。  
播放控制按鍵  
9
按下可開始播放。  
4
MENU  
如果已載DVD-Video、最終化DVD-R/-RW 或最終化  
碟片,按下可顯示最上層選單。  
按下可停止播放。  
DVD+R/+RW  
5
ꢀ/ꢁ/ꢂ/ꢃ (游標按鍵)ENTER  
按下可停止播放或錄製。  
用於導覽所有螢幕功能選單。按下  
的選項。  
選擇目前反白  
ENTER  
/ꢅ  
6
按下可顯示  
HOME MENU  
按下可開始倒退或快轉掃描。再按一次可變更速度。  
,您可以在其中導覽錄影機的  
Home Menu  
所有功能。  
/ꢇ  
按下可跳到上一個或下一個標題/章節/曲目/  
資料夾,或顯示上一個或下一個選單頁面。  
7
按下可返回上一層的螢幕功能選單或顯示畫面。  
RETURN  
//ꢋ  
暫停時,按住可開始慢動作播放。反覆按可以變更  
播放速度。  
暫停時,按下可往前或往後移動一格。  
10 CM BACK (返回廣告)  
反覆按下可逐漸往後跳經視訊播放過程。  
(略過廣告)  
CM SKIP  
反覆按下可逐漸往前跳經視訊播放過程。  
20  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
03  
控制與顯示  
11 JUKEBOX  
按下可顯示硬碟  
錄影機的點唱機畫面,在此畫面  
/DVD  
裝入遙控器電池  
中可以將要播放的音樂複製到硬碟中。  
1
打開遙控器背面的電池槽蓋。  
12  
(AUDIO)  
按下可變更聲音語言或聲道停止錄影機時,按  
下可變更調諧器音效。)  
請依照電池槽內的極性指( , 將兩顆  
2
鹼性電池放入電池槽中。  
AA/LR6  
(SUBTITLE)  
按下可顯示/變更多語  
幕。  
碟片中內建的字  
DVD-Video  
(ANGLE)  
按下可切換有多角度場景的碟片之拍攝角度。  
數字按鍵  
13  
使用數字按鍵選擇曲目/章節/標題或選擇頻道。  
闔上電池蓋。  
3
CLEAR  
按下可清除任何輸入的內容並重新輸入。  
注意  
14 CH +/–  
按下可變更內建電視調諧器的頻道。  
使用錯誤的電池可能引起危險,如漏液及爆炸。請  
遵守以下事項:  
15 INPUT  
按下可變更用於錄製的硬碟  
請勿混合新舊電池使用。  
錄影機輸入。  
/DVD  
請勿混合不同的電池使用 雖然外觀類似,但不同  
的電池可能含不同的電壓。  
16 DISP  
顯示/變更顯示的螢幕功能資訊。  
請確定電池的正負兩端與電池槽中的指示相符。  
17 錄製控制按鍵  
若設備不使用的時間超過一個月,請取出電池。  
ì REC  
處理廢舊電池時,請遵守政府條例或適用於貴國或  
地區的環境公共指令規則。  
按下可開始錄製。反覆按可以 30 分鐘為區段來設定  
錄製時間。  
STOP REC  
按下可停止錄製。  
警告  
請勿在陽光直射或其他過熱的地方使用或存放電池,  
如車內或暖爐旁。否則電池可能漏爆炸或起火。  
同時也會縮短電池的壽命或效能。  
21  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
03  
控制與顯示  
選擇與操作來源設備  
使用遙控器  
使用遙控器時,請務必記住下列事項:  
HDMI  
1
2
3
TV  
FM/AM  
LINE  
1
按下可切換連接的設備。  
請確定遙控器與裝置上的遙控感應器間無阻礙物。  
所選擇的設備改變,而且遙控器的液晶螢幕變成該適用  
設備的控制畫面。  
若有強光或螢光燈照射在裝置的遙控感應器上,則  
可能無法使用遙控操作。  
不同裝置的遙控器可能會互相干擾。請避免在此裝  
置附近使用其他設備的遙控器。  
若要選擇用Digital 1Digital 2Analog、  
Front Audio In iPod 的輸入,請LINE 按鍵,  
直到所需的輸入功能顯示在顯示裝置上為止。  
若發現遙控器在操作範圍內無法操作時,請更換電  
池。  
2
用的輸入來源。  
HDMI 1  
HDMI 3  
LINE  
時,選取您正在使  
選擇  
請如下圖所示,在顯示裝置的遙控感應器操作範圍  
前方使用遙控器。  
液晶螢幕變成所選擇設備的控制畫面,然後您可以操作  
所需的設備。  
HDD/  
DVR  
HDD/  
DVR  
BD  
DVD  
BD  
DVD  
TV  
30  
30  
EXIT  
EXIT  
7 m  
HDMI輸入  
LINE輸入  
找不到所需的音源,或連接不是先鋒製造的設備時,  
RCV 讓遙控器進接收」模式。本機的輸入  
保持不變。  
操作遙控器  
備註  
隨附的遙控器除了能控制接收重低音揚聲器外,還可以  
控制先鋒的電漿電視、DVD 播放器、Blu-ray Disc 播放機  
和硬/DVD 錄影機等其他產品。  
若要在透過本機聆聽來自連接設備的音效時暫時控  
制接收,請按  
。所選擇的輸入不會改變,但遙  
RCV  
控器變更接收」模式。若要返回前一個操作模  
式,請再按一次  
若要操作這些設備,請將遙控器指向顯示裝置。  
RCV  
操作接收重低音揚聲器  
使用液晶觸控畫面  
RCV  
按下可顯RECEIVER 畫面。  
畫面顯示在遙控器的液晶螢幕上,而且遙控  
液晶觸控畫面是否有多個資訊頁面視您操作的連接設備  
DVD 播放器)而定。您要控制的設備未顯  
示時,PAGE 捲動至您要控制的設備所在的頁面。  
RECEIVER  
器切換接收」模式。  
超過  
秒沒有執行任何操作時,顯示在遙控器上的  
10  
RECEIVER  
液晶觸控畫面會自動關閉。若要使此畫面再次顯示,  
請觸碰遙控器的液晶螢幕或按任何按鍵。  
ADV  
F.S.  
SURR  
SURR SURR  
22  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
04  
開始操作  
第 章  
4
開始操作  
將麥克風連接至顯示裝置背面的  
插孔。  
1
MIC  
MCACC SETUP  
重要  
RCV  
按下可將遙控器設定為操作接收重低音揚聲器  
的接收控制模確定液晶螢幕顯示以下所示的  
畫面。  
請將麥克風置於正常的聆聽位置。  
請放在耳朵高度,並使用桌椅確保麥克風保持水平位  
2
RECEIVER  
置。  
請確定麥克風與揚聲器間無障礙物。  
RECEIVER  
RECEIVER  
ADV  
F.S.  
SURR  
SURR SURR  
3
將其電源開啟。  
RECEIVER  
若接收重低音揚聲器關閉,按下  
MCACC  
按下  
MCACC  
4
按下  
使MCACC」設定以達最佳環  
繞音效  
MCACC  
後,請盡可能保持安靜。音量將會自動變  
大,系統會輸出一連串的測試音。  
若要在完成前取消自動  
MCACC  
裝置將會繼續使用之前的設定值。  
下  
MCACC  
多聲道音場自動補MCACC)系統可測量聆聽區域  
內的音場特性,將週遭環境的雜音納入考量,並測試聲  
道延遲與聲道音量。完成系統附贈的麥克風設定後,系  
統將會利用一系列的測試音資訊測量駐波與迴響,使特  
定房間內的揚聲器設定值與等化效MCACC 效果)  
若週遭的雜音過多,  
Noisy!  
(雜音太大)將會在顯  
2
示幕中持續閃爍五秒。若要結束並檢查雜音等級 ,  
按下  
按下  
或再試一次,顯示幕中顯示  
時,  
Retry  
MCACC  
ENTER  
1
達最佳化。  
若顯示幕中出現  
(麥克風發生錯誤!)  
(揚聲器發生錯誤!)訊息,則  
Error MIC!  
Error Speaker!  
重要  
表示麥克風或揚聲器的連接可能出現問題。若要重  
用於自動  
設定的測試音音量極請勿在  
MCACC  
3
試,請按下  
ENTER  
設定期間將音量轉小,否則可能無法達到最佳設定  
狀態。  
MCACC 設定完成後,音量將會恢復為正常音量,顯示  
4
5
幕中出Complete 並啟動音場自動補正等化功能。  
請勿MCACC 設定期間移動麥克風與揚聲器。  
MCACC」設定時,務必將麥克風從本機  
上拔下。  
附註  
1
2 •  
MCACC  
若房間的環境不適合進行最佳的自動  
您只需進行一次自動  
設定 (除非您變更揚聲器擺設或房間佈置)。  
MCACC  
設定 (週遭雜音過多、牆壁迴音、含阻礙揚聲器與麥克風的物體),則最後的設定值可能會發生錯  
誤。請檢查可能影響室內環境的家電用品 (冷氣機、冰箱、電扇等),如有必要,請關閉其電源。  
MCACC  
部分舊型的電視機可能會與麥克風互相產生干擾。 若發生此情形,請在自動  
設定期間關閉電視機。  
3
MCACC  
、關閉電源,並根據  
Error  
MCACC  
訊息檢查問題,然後重試自動 設定。  
若仍無法解決問題,按下  
4 若未顯Complete,很可能在設定期間發生錯誤檢查所有接線並再試一次。  
27 MCACC MCACC  
5
請參閱第  
頁上的以  
效果聆聽 以開啟/關閉  
效果。  
23  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
05  
聆聽您的系統輸出的音效  
第 章  
5
聆聽您的系統輸出的音效  
以環繞聲播放的立體聲  
由前聲道輸出人聲時,從環繞聲揚聲器輸出音效。  
您可以播放例如 等無縫、舒適的環繞立體聲音  
重要  
RCV  
按下可將遙控器設定為操作接收重低音揚聲器  
的接收控制模確定液晶螢幕顯示以下所示的  
畫面。  
CD  
源。在自動聆聽模式中播放立體聲立源時,可使用  
此效請參閱下列說明。  
RECEIVER  
依下列操作可以關閉有效聲音模啟動直接模式:  
RECEIVER  
DIRECT  
按下可切換直接聲音。  
按下此按鍵切有效聲音」直接聲音。  
ADV  
F.S.  
SURR  
SURR SURR  
直接聲音」時,DIRECT 指示燈亮起。  
有效聲適用於最佳聲音)  
自動聆聽模式  
自動聆聽模式是聆聽系統控制任何來源的最簡單方式:  
有效聲音模式藉由本機提供的特殊形狀高品質揚聲器,  
帶來下列針對極致的影片與音樂原音體驗而設計的先鋒  
獨家專有音效技術。  
揚聲器的輸出會反映出來源資料的聲道。  
若您將系統設定為前環繞第 頁則前場前環繞  
6
在一般情況下開啟有效聲音模式,使本機發揮最大的功  
能。  
聲模式將會提供最佳的輸出結請參閱第  
。  
26  
對話增強  
影片中的清晰對話,與背景聲音相較之下更顯突出。  
SURR  
按下可選擇  
聆聽模式。  
Auto  
動態範圍壓縮  
重現易受周遭雜音影響的細部聲音,建立讓您感覺  
身歷其境的聲音環境。  
以環繞音效聆聽  
您可以在環繞音效下,聆聽立體聲或多聲道來源。環繞  
原始聲道平衡與聲道混合  
由於隨附揚聲器的方向經過特別設計,因此以特殊  
方式縮混和平衡聲道。此外,本機也根據播放的內  
容達到最佳平衡。  
音效是以取自使用其中一種  
解碼模式的立體聲音源所產生。  
Dolby Pro Logic  
DTS  
1
Neo:6  
若您將系統設定為前環繞第 頁則前場前環繞  
6
頻率特性修正  
除了隨附揚聲器的新增功能外,實現為了長時間聆  
聽而最佳化的播放特性。  
聲模式將會提供最佳的輸出結請參閱第  
。  
26  
SURR  
反覆按下可選擇任一聆聽模式。  
顯示幕中出現的選項視播放的來源類型而有所不同。  
2
附註  
1
DTS-ES  
6.1/7.1  
聲道音效後環繞聲訊號後,原始虛擬後環繞功能輸出結合環繞聲訊號的後環繞聲訊號。  
在適當解碼由  
2 DTS-HDDTS-Express Dolby TrueHD 176.4 kHz/192 kHz)時,無法選擇自動和立體聲以外的模式外,您無法選擇使用於 Dolby Digital  
Plus Dolby TrueHD 96 kHz DTS Neo:6  
呈現的  
(低於  
)的  
24  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
05  
聆聽您的系統輸出的音效  
搭配雙聲道來源時,您可以選擇:  
ENTER  
-自動聆聽模請參閱第  
頁)  
24  
Auto  
3
ENTER  
確認。  
調整設定值,然後按下  
)-  
聲道  
2PL II Movie Dolby Pro Logic II Movie  
環繞音效,特別適合影片來源  
5.1  
5.1  
中央影像設定  
)-  
聲道  
2PL II Music Dolby Pro Logic II Music  
模式中聆聽雙聲道音源請參閱  
Neo:6 Music  
24  
環繞音效,特別適合音樂來源,請參閱下文的  
設定值  
Dolby  
您也可以調整中央影像效果。  
Pro Logic II Music  
2
調整中央影像,以人聲建立更寬廣的立體聲效果。  
2PL II GameDolby Pro Logic II Game5.1 聲道  
環繞音效,特別適合電視遊戲  
SOUND  
1
在啟Neo:6 Music 模式時按下。  
2Pro Logic Dolby Pro Logic4.1 聲道環繞音  
效,適用於雙聲道來源  
ENTER  
Neo:6 Cinema  
6.1  
聲道來源,特別適合影片來源  
聲道音別適合音樂片來,  
6.1  
「  
然後按下  
Center Image  
ENTER  
2
3
Neo:6 Music  
請參閱下文的中央影像設定  
-請參閱第 頁上的以立體聲聆聽  
ENTER  
調整設定值,然後按下  
確認。  
ENTER  
調整從 (所有傳送到右前置與左前置揚聲器的中央  
Stereo  
26  
0
搭配多聲道音源時,您可以選依格式:  
10  
聲道)到  
效果。  
(僅傳送到中置揚聲器的中央聲道)的  
Auto -自動聆聽模請參閱24 頁)  
StandardDecode Dolby DigitalDTS環繞聲解  
碼聆聽。播放有最標準解碼器的 Dolby DigitalDTS  
多聲PCM 等多聲道音源。  
使先進環繞聲」功能  
-請參閱第  
頁上的以立體聲聆聽  
26  
Stereo  
「先進環繞聲」效果適用於任何多聲道或立體聲音源,  
提供各種多樣的環繞音效。這些模式是以使用6 頁上  
所述的標準環繞設定時提供最佳聆聽效果而設計。  
Dolby Pro Logic II Music 設定值  
可調整三種設定值:中置寬度、尺寸及全景。  
如上述)聆聽時,您  
Dolby Pro Logic II Music  
ADV  
SURR  
按下可選先進環繞聲」模式。  
指示燈亮起。您無法  
選擇其中一個模式時,  
ADV.SURR.  
切換適用於某些音訊流的模式。  
3
SOUND  
1
在啟Dolby Pro Logic II Music 模式時按下。  
反覆按下可選擇:  
ENTER  
-針對有動態音軌的動作片而設計  
Action  
「  
」、「  
ENTER  
」或  
Dimension  
2
Center Width  
-針對有很多對話的影片而設計  
Drama  
然後按下  
1
Panorama  
-針對有很多特效的科幻片而設計  
Sci-Fi  
-提升前置揚聲器的混音效果,將  
Center Width  
右前與左前揚聲器的中央聲道擴散出來,音域聽起  
-建立來自單聲道音軌的環繞聲  
Mono Film  
來更較高設定值)或更較低設定值。  
-由前而後調整環繞音效平衡的深度,  
Dimension  
使聲音聽起來更負設定值)或更正設定  
。  
-可將前置立體聲音像延使環繞揚聲  
Panorama  
器產生全面」的音效。  
附註  
1
C.Width 3  
設定。  
由於本產品使用雙重中置揚聲器系統,因此正常來說您應該使用  
2 由於本產品使用雙重中置揚聲器系統,因此正常來說您應該使用 C.Image 3 設定。  
3
您無法將此功能使用於下列音訊流:  
Dolby TrueHD 88.2 kHz  
:超過  
DTS-HD:超88.2 kHz 或擁2/0 的聲道格式  
DTS-Express 2/0  
:擁有  
的聲道格式  
25  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
05  
聆聽您的系統輸出的音效  
Ent.Show  
-適用於音樂音源  
-創造特寬的立體聲音場  
Expanded  
類型同步化模式  
-為單音和立體聲電視來源提供環繞聲  
只有在本機連接HDMI Control 相容先鋒硬碟 /DVD 錄  
影機和使HDMI Control 功能時,您才能運用類型同步  
化模式將聆聽模式自動變更為最符合錄影機播放內容之  
類型的聆聽模式。  
TV Surround  
-適用於電視遊戲  
Advanced Game  
Sports -適合用於觀賞體育節目  
Classical -提供大型音樂廳的音效  
HDMI Mode 設定AMP Mode 36 。  
Rock/Pop  
奏音效  
-創造適合搖滾樂和/或流行樂的現場演  
GENRE  
在聆聽來自錄音器的媒體內容時按下。  
-適用於聲樂音源  
Unplugged  
選擇最適當的聆聽模式並顯示在顯示畫面中。無法判斷  
相關類型時,可能顯No Genre Can’t use,而且聆  
聽模式維持不變。  
-使用所有揚聲器為立體聲音源提供多聲  
Ext.Stereo  
道聲音  
提示  
使用前場前環繞聲模式  
6
主要搭配點唱機和  
來源使用。  
MP3  
如第 頁所述使用前環繞揚聲器設定時,可以使前  
場前環繞聲」模式。  
若要使用此功能,您必須有透過  
相容先鋒硬碟  
功能設定開啟。  
連接的  
錄影機,並且將  
HDMI  
HDMI  
HDMI  
Control  
Control  
/DVD  
F.S.  
SURR  
按下可選擇前場前環繞聲模式。  
指示燈亮起。  
F.S.SURR  
反覆按下可選Focus 5.1chWide 5.1ch Extra  
使聲音修正器」功能  
Power。您無法為某些音訊流選額外功率」以外的  
1
若在  
壓縮過程中移除音效資料,聲音品質  
WMA  
MP3  
通常會出現不平均的音像聲音修正器」功能採用新  
技術,可藉由還原聲壓及修整壓縮後的人工缺  
模式。  
Focus 5.1ch -用於提供引導到左側與右側揚聲器的  
聲音投射聚集中央區域的豐富環繞音效。  
DSP  
陷,將  
的音效品質恢復至壓縮的雙聲道音效。  
CD  
-用於提供比  
Wide 5.1ch  
廣的環繞音效。  
模式音域更寬  
Focus 5.1ch  
SOUND  
RTRV  
2
在聆聽立體聲音源時按下 。  
-從環繞揚聲器輸出立體多聲道  
Extra Power  
音源、向下混合立體聲)以提供強大的環繞音效。  
反覆按下可在以下兩項功能間進行切換:  
聲音修正器。  
聲音修正器。  
Retriever On —  
Retriever Off —  
以立體聲聆聽  
您可以使用立體聲聽取任何來立體聲或多聲道。播  
放多聲道來源時,所有聲道經過縮混後傳送到左前置/  
右前置揚聲器和重低音中。  
SURR  
反覆按下,直到顯示幕中出現  
STEREO  
附註  
1
您無法將此功能使用於下列音訊流:  
Dolby TrueHD:超88.2 kHz  
DTS-HD  
DTS-Express  
88.2 kHz  
2/0  
或擁有 的聲道格式  
的聲道格式  
:超過  
2/0  
:擁有  
2 此設定無法搭配多聲道音源使用。此外,如果是搭SACDDTS-HDDTS-ExpressDolby TrueHDDolby Digital Plus PCM192 kHz/176.4 kHz,  
甚至無法使用立體聲音源。  
26  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
05  
聆聽您的系統輸出的音效  
MCACC  
使用以  
效果聆聽  
取得的修正音場設定聆聽聲音。  
調整低音及高音  
使用低音及高音控制調整整體音調。  
MCACC  
SOUND  
SOUND  
1
2
3
按下可開啟音效選單。  
按下可開啟音效選單。  
1
ENTER  
ENTER  
1
Tone然後按ENTER。  
「  
MCACC Effect  
然後按下  
ENTER  
2
ENTER  
ENTER  
「  
然後按  
ENTER  
Bass/Treble  
3
MCACC OnMCACC Off,  
Bass/Treble 以取午夜響度」及  
「寂靜」聆聽模式。您無法同時使用這些模式。  
然後按ENTER 確認。  
關閉時,等化、聲道延遲、聲道位  
準和駐波也會關閉。  
MCACC Effect  
ENTER  
MCACC Effect 關閉時,您可以手動控制聲道延遲和  
聲道位準,MCACC Effect 開啟時,您可以手動個別  
儲存設定值。  
4
使ꢂ/ꢃ BassTreble。  
使ꢀ/ꢁ 按鍵調整音效,然後ENTER 確認。  
低音和高音的調整範圍-6dB +6dB 之間。  
MCACC 效果」在使MCACC 設定」後自  
動設定為開啟。  
低音或高音設定0dB 以外時,TONE 指示燈亮起。  
調整聲音延遲  
使午夜響度」寂靜」聆  
聽模式  
「午夜」聆聽功能可讓您以低音量收聽實際的環繞音效。  
有些顯示器在播放視訊時會有稍微的延遲,因此音軌會  
與畫面稍微沒有同步。新增一點延遲可以調整聲音,使  
聲音的播放符合畫面的顯示。  
使響度聆聽」功能可以在低音量時,取得來自音樂  
音源的良好低音與高音。  
您可以調整的間位準)共有  
個,總範圍是  
60  
200 msec  
「寂靜」聆聽功能可降低音源中過量的低音或高音。  
SOUND  
1
按下可開啟音效選單。  
SOUND  
按下可開啟音效選單。  
1
2
ENTER  
2
Sound Delay然後按ENTER。  
ENTER  
1
Tone然後按下 ENTER。  
ENTER  
選擇聲音的延遲長度,然後按  
確認。  
,此  
On  
3
ENTER  
設定中自動延遲」設定為  
HDMI  
ENTER  
3
MidnightLoudness」或  
如果在  
2
然後按  
Quiet  
若要取午夜響度」寂靜」聆聽模式,  
以確認。  
選項會關閉且不顯請參閱第  
動延遲。  
頁上的設定自  
39  
ENTER  
請選擇  
Bass/Treble  
附註  
1 DTS-HD (超88.2 kHzDolby TrueHD (超過 88.2 kHz)音訊流時,如果已選Bass/Treble 以外的模式,則您無法選擇 Tone。  
DTS-HD 88.2 kHz Dolby TrueHD 88.2 kHz Bass/Treble  
2
播放  
(超過  
)或  
(超過  
)音訊流時,您無法選擇  
以外的模式。  
27  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
06  
收聽廣播  
第 章  
6
收聽廣播  
改善  
接收不良  
FM  
重要  
若您正以立體聲收聽  
電台,但收訊不佳,可切換至  
FM  
單聲道以便改善音效品質。  
FM/AM  
若要收聽廣按下  
按鍵將遙控器設  
FM/AM  
控制模式。遙控器上的液晶螢幕切換至  
定為  
FM/AM  
畫面。  
FM/AM  
SETUP  
ENTER  
調到  
廣播電台後按下。  
FM  
1
2
3
4
FM/AM  
「  
然後按下  
Tuner Setup  
ENTER  
1
2
3
ENTER  
FM Auto/Mono  
選擇「  
ENTER  
後按下  
收聽廣播  
調諧器可接收  
ENTER  
廣播,並讓您能將最愛收聽的  
AM  
FM Mono然後按下 ENTER。  
FM  
電台記憶下來,如此便不需在每次收聽時進行手動調  
選。  
調諧器處於單聲道接收模式時,單聲道指示燈 (  
會亮起。  
選取上述的 FM Auto,便可切換回自動立體聲模式  
切換至調諧器,然後反覆按可選擇  
1
波段。  
FM/AM  
FM  
AM  
(接收立體聲廣播時,立體聲指示(  
)會亮起。  
顯示幕會顯示波段及頻率。  
AM 音效不佳  
改善 收音機音效品質最簡單的方式就是確定房間內  
AM  
的電視機是否關機。您也可以試著改變  
位置與方向。  
TUNE  
-
+
2
調選需要的頻率。  
迴路天線的  
AM  
共有三種調諧模式可供選動、自動及高速:  
手動調諧-反覆按  
可變更顯示的頻率。  
TUNE +/–  
自動調諧-按住  
直到頻率顯示開始移動後  
TUNE +/–  
改變雜音抑制模式  
進行上述動作後,若仍無法改善  
放開。調諧器會停在下一個搜尋到的電台。持續此  
動作便可繼續搜尋。  
音質,您可使用不  
AM  
同的雜音抑制模式獲得改善。只要選擇聽起來最好的音  
效即可。  
高速調諧-按住  
直到頻率顯示開始快速移  
TUNE +/–  
動。繼續按住按鍵,直到找到要收聽的頻率為止。  
必要時,請使用手動調諧微調頻率。  
SETUP  
調到  
廣播電台後按下。  
AM  
1
2
3
ENTER  
ENTER  
ENTER  
「  
「  
然後按下  
Tuner Setup  
ENTER  
然後按下  
Noise Cut  
ENTER  
4
選擇雜訊抑制模12 3然後按下  
ENTER  
28  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
06  
收聽廣播  
記憶電台  
改變頻率間隔  
30  
您可以儲存高達  
個預設電台,如此便可輕鬆收聽喜  
若發現無法調諧電台,則本系統的頻率間隔可能不適用  
於您所在的國家/地區。  
愛的電台,不必每次進行手動調選。  
1
FM AM  
調諧至  
廣播電台。  
SETUP  
ENTER  
按下  
SETUP  
1
2
3
4
FM  
視需要選擇單聲道或自動立體聲接或雜訊抑  
制模AM這些設定值與預設設定一併儲存。  
「  
然後按下  
ENTER  
System Setup  
SETUP  
2
3
4
5
SETUP。  
ENTER  
ENTER  
ENTER  
ENTER  
Tuner Setup然後按下 ENTER。  
ST.Memory然後按下 ENTER。  
選擇您要收聽的預設電台,然後按下  
選擇 「AM9K/10K然後按ENTER。  
ENTER  
選擇設定值,然後按下  
以確認。  
ENTER  
間隔  
間隔;  
AM 9K  
AM  
9 kHz  
FM  
50 kHz  
AM 10K AM 10 kHz 間隔;  
FM 100 kHz 間隔  
ENTER。  
收聽預設電台  
1 請確定已選取調諧功能。  
ST  
-
+
2
選擇預設電台。  
或者使用數字按鍵直接選取預設電台。  
29  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
07  
環繞音效設定值  
第 章  
7
環繞音效設定值  
SETUP  
ENTER  
1
2
3
SETUP。  
重要  
RCV  
按下可將遙控器設定為操作接收重低音揚聲器  
的接收控制模確定液晶螢幕顯示以下所示的  
畫面。  
Sound Setup然後按ENTER。  
ChannelLevel然後按ENTER。  
RECEIVER  
ENTER  
RECEIVER  
ADV  
F.S.  
SURR  
SURR SURR  
使用  
鍵調整該聲道的位準。  
按鍵選擇聲道,或使用  
ꢀ/ꢁ  
4
ꢂ/ꢃ  
2
每個聲道的位準調整範圍為±  
10 dB  
使聲音設定」選單  
聲音設定」選單中,您可以使用系統全部的環繞聲  
設定。  
ENTER  
在完成時按下。  
5
若再次使用自動  
設定。  
會取代此處所做的  
MCACC  
設定時,以下字母各自代表的揚聲器為:  
L 前置揚聲器  
1
揚聲器距離設定  
C 置揚聲器  
自動 MCACC 請參閱23 頁)應能提供最佳的  
環繞音效設定。然而您可能會發現,進一步調整揚聲器  
距離設定值可提升房間內的環繞音效。  
前置揚聲器  
R  
環繞揚聲器  
環繞揚聲器  
SR  
SL  
SW  
從正常的聆聽位置設定每個揚聲器的距離。  
低音揚聲器  
ENTER  
SETUP  
開啟 「  
」選單。  
1
2
3
Sound Setup  
1
聲道位準設定值  
自動  
請參閱第  
頁)應能提供最佳的  
23  
MCACC  
ENTER  
環繞音效設定。然而您可能會發現,更進一步調整聲道  
位準可提升房間內的環繞音效。  
Distance然後按ENTER。  
這種設定聲道位準的方式可讓您收聽來源並調整每個播  
放聲道的位準。  
使ꢂ/ꢃ 按鍵選擇揚聲器,或使ꢀ/ꢁ  
更進階的聲道位準設定方式則是使用測試音。詳情請參  
按鍵調整距離。  
每個揚聲器的距離調整範圍為  
9.0m  
0.1m  
閱第  
頁上的使用測試音調整聲道位準。  
32  
ENTER  
4
完成時按ENTER。  
若再次使用自動 功會取代此處所做的  
MCACC  
設定。  
附註  
1
2
MCACC Effect  
MCACC  
功能調整之相同功能的值會遭到取代。  
在開啟  
後設定此功能時,以自動  
MCACC Effect 時,套用在這裏設定的值,與使用自動 MCACC 調整的值無關。 (不會取代自MCACC 設定。)  
51  
音量設定超過  
時,調整範圍會受到限制。  
30  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
07  
環繞音效設定值  
動態範圍控制  
雙單聲道設定值  
Dolby Digital  
DTS  
包括部分對使用其中一項動  
Dolby Digital  
指定雙單聲道 音軌的播放方式。您也可以  
以低音量觀賞  
清楚聽到低位準音效  
資料時,您可能無法  
DVD-RW  
碟片  
使用此設定值,切換使用雙語音效錄製的  
聲道。  
DRC  
態範圍控設定值便可提高低位準音效,同時  
控制高位準高音。  
ENTER  
動態範圍控制僅適用於  
軌。  
音軌及部分  
Dolby Digital  
DTS  
SETUP  
開啟 「  
」選單。  
1
2
3
Sound Setup  
ENTER  
ENTER  
「  
然後按下  
Dual Mono  
ENTER  
SETUP  
「  
」選單。  
1
2
3
Sound Setup  
ENTER  
選擇設定。  
「  
D.R.C.  
然後按下  
ENTER  
請選擇以下其中一個設定:  
-僅播放聲道  
-僅播放聲道  
CH1 Mono  
1
2
選擇設定。  
CH2 Mono  
請選擇以下其中一個設定:  
CH1/CH2 -兩個聲道皆由前置揚聲器播放  
-僅適用於  
訊息。選擇  
以外  
Dolby TrueHD  
D.R.C. Auto  
D.R.C. High  
的訊號。  
Dolby TrueHD  
用於  
D.R.C. Mid  
ENTER  
按下可結束。  
4
D.R.C. High -減少動態範降低大聲音量並提高  
較小聲的音效)  
D.R.C. Mid -中等設定  
D.R.C. Off  
使用此設定)  
-無動態範圍調以較高音量聆聽時請  
ENTER  
按下可結束。  
4
31  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
07  
環繞音效設定值  
使用虛擬後環繞模式  
本模式可讓您透過您的環繞聲揚聲器聽到虛擬後環繞聲  
道。您可以選擇聆聽沒有後環繞聲道資訊的音源,或如  
使用測試音調整聲道位準  
您也可以使用測試音作為參考設定聲道位準,而不需播  
放來請參閱30 頁上的聲道位準設定值每個  
揚聲器會輪流播放測試音,以供您在播放時調整位準。  
5.1  
果聲音以原始編碼格例如  
)聽起來較佳,您可  
Dolby Digital EX  
以讓接收重低音揚聲器將此效果套用到  
1
DTS-ES  
6.1  
編碼音源中。  
1
您也可以使用測試音來調整環繞聲的聲道位準。  
TEST  
TONE  
ENTER  
執行音調測試。  
每個揚聲器會輪流播放測試音。  
1
SETUP  
ENTER  
「  
」選單。  
Sound Setup  
將音量調到  
以下。  
50  
然後按下  
Virtual SB  
ENTER  
2
播放時,調整聲道位準。  
此目的在於調整位準,確保您從每個揚聲器聽到的測試  
2
選擇設定。  
3
請選擇以下其中一個設定:  
音音量皆相同。每個聲道的位準調整範圍為±  
10 dB  
您也可以使用VOL +/–按鍵調整測試音輸出的整體音  
不會影響聲道位準設定值。  
-一定使用虛擬後環例如  
編碼資  
5.1  
Vir.SB On  
料)  
由於重低音會產生超低頻率,其實際音效可能更大  
聲。我們建議聆聽來源時,調整重低音位準。  
請參閱30 頁上的聲道位準設定值。  
-虛擬後環繞自動套用到 編碼音源中  
6.1  
Vir.SB Auto  
(例如  
進環繞聲模式)  
或先  
Dolby Digital EX  
DTS-ES DTS Neo:6  
Vir.SB Off -虛擬後環繞模式關閉  
ENTER  
完成時,按下可結束測試音設定。  
3
若再次使用自動  
設定。  
會取代此處所做的  
MCACC  
ENTER  
按下可結束。  
4
衰減  
LFE  
Dolby Digital  
DTS  
音源包括極低的低音。  
有些  
視需要設定  
衰減器,以避免揚聲器的極低音失真。  
LFE  
設定為建議值  
時不受限制定為  
LFE  
0dB  
-5dB  
受到各等級的限制。  
時,  
-20dB LFE  
-10dB -15dB  
選擇  
時,  
聲道不會輸出任何聲音。  
LFE  
Off  
ENTER  
SETUP  
ENTER  
「  
」選單。  
Sound Setup  
1
2
3
「  
然後按下  
ENTER  
LFE ATT  
ENTER  
調整設定值,然後按下  
確認。  
ENTER  
附註  
1
虛擬後環繞聲模式是否有效視輸入訊息和聆聽模式而定。  
32  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
08  
其他接線  
第 章  
8
其他接線  
連接類比音效設備  
重要  
您可以使用  
比音效設備。  
插孔連接收錄音機等類  
ANALOG AUDIO IN  
在本機的側面板上進行接線或變更接線時,請務必  
關閉電源,並將電源線插頭自牆上電源插座上拔除。  
完成所有接線後,再將電源線插頭接上電源插座。  
接收重低音揚聲器  
連接輔助設備  
您也可以將類比和數位的外接音訊來源連接至本系統。  
側面板  
數位音訊來源包括數位衛星接收器、  
錄音器等。  
CD  
L
建議您使用  
連接線來連接有  
端子的音訊來  
HDMI  
HDMI  
源。如需詳細資訊,請參閱第  
頁上的使用  
35  
HDMI  
R
。  
ANALOG  
AUDIO IN  
若要聆聽來自電視機的音效,請將電視機的音訊連接線  
連接至本機的其中一個輸入插孔。  
從音訊輸出  
數位音訊的連接  
本系統有光學數位輸入插孔。使用這些插孔連接  
錄音器等外接設備。  
MD  
收錄音機、MDDAT等  
CD  
使用顯示裝置F.AUDIO 輸入插孔可輕易播放數位音訊  
播放器PC 的音效。使用立體聲迷你插頭連接線將音  
訊來源連接至顯示裝置。  
接收重低音揚聲器  
將連接線接上  
換至  
插孔時,本機的輸入自動切  
F.AUDIO  
Front Audio In  
側面板  
顯示裝置  
DISPLAY UNIT  
IN  
1
IN  
2
iPod  
MCACC  
SETUP MIC  
SYSTEM  
F.AUDIO  
OPTICAL  
DIGITAL  
F.AUDIO  
從數位音訊  
輸出(光學)  
MDCD錄音器等  
將側面板的  
的光學輸出插孔。  
從類比音訊  
輸出  
插孔連接至外接播放設備  
OPTICAL IN 2  
數位音訊播放器等  
立體聲迷你插頭連接線  
這些設備包括  
數位設備。  
播放器、數位衛星接收器或遊戲機等  
MD  
不使用  
用它連接外部設備。  
輸入電視機的聲音時,您也可以使  
OPTICAL IN 1  
33  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
08  
其他接線  
iPod  
連接  
聆聽外接音訊來源  
您可以使用顯示裝置上iPod 插孔播放來iPod 旳音  
樂。所有操作都可以透iPod 執行。使用隨附的 iPod  
連接線iPod 連接至本機。  
若要使用本機聆聽來自所連接外部設備的音效,請在遙  
控器上選擇該設備的輸入功能使用此遙控器可以控制  
某些先鋒產品。  
iPod 時,本機的輸入自動切換iPod。  
iPod  
機種的接頭跟本機不相容。  
有些  
1
RECEIVER  
便可開機。  
若系統尚未開機,按下  
同時請確定外接來電視機、衛星接收器等)的電源  
已開啟。  
顯示裝置  
LINE 選擇音訊輸入來源。  
2
輸入來源的顯示順序如下所示:  
DISPLAY UNIT  
iPod  
MCACC  
SETUP MIC  
SYSTEM  
F.AUDIO  
Digital 1  
Digital 2  
Analog  
iPod  
iPod  
Front Audio In  
液晶螢幕切換至該選擇輸入來源的畫面。  
按下所連接設備的按鍵。  
連接的設備未顯示在畫面上,或連接不是先鋒製造的設  
備時,按下 按鍵使遙控器顯示在接收重低音揚聲器  
3
RCV  
操作畫面上。  
iPod R  
iPod連接線  
必要時,開始播放外接來源。  
4
iPod  
Music  
>
Extras  
Settings  
>
>
Shuffle Songs  
Backlight  
MENU  
®
iPod  
Apple Inc.  
在美國及其他國家已經註冊之商標。  
34  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
08  
其他接線  
連接外接天線  
若為外AM 天線,請使5 m 6 m 的乙烯基絕緣電  
關於控制輸出連接  
有多種先鋒設備支CONTROL 連接,將這些連接設備  
的遙控器對準其中一個設備的感應器即可使用。  
線,並安裝於室內或室外。請保持迴路天線的接線。  
若為外FM 天線,請使PAL 接頭連接外接FM 天  
線。  
使用遙控器時,控制訊號會沿著電路傳達至適當的設  
備。  
HDMI  
如果您選擇使用此功能,請確定至少將一組  
比音效插孔連接至其他設備上,作為接地用途。  
或類  
外接FM天線  
接收重低音揚聲器  
在任一側使用隨附的控制連接線,將另一個先鋒設  
備上的 插孔連接至接收重低音揚聲器上的  
CONTROL IN  
插孔。  
CONTROL OUT  
將遙控器指向本接收重低音揚聲器隨附的顯示裝置可控  
制其他設備。  
側面板  
ANTENNA  
AM LOOP  
HDMI  
使用  
連接  
HDMI  
DVI  
HDCP  
(有 )的設備,您可  
如果您有配備  
以使用市售的  
FM  
HDMI  
連接線將它連接至本接收重低音揚  
UNBAL 75 Ω  
1
AM迴路天線  
聲器。  
連接傳送未壓縮的數位視訊,以及幾乎每一種  
HDMI  
與連接的設備相容的數位音訊,包括  
外接AM天線  
VCD  
DVD-Video  
、超級  
PAL接頭  
DVD-Audio SACD Blu-ray Disc VCD  
等。  
MP3  
CD  
室內天線  
(乙烯基塗料金屬線)  
接收重低音揚聲器  
HDMI  
室外天線  
5 m6 m  
T
IN 3  
IN 2  
IN 1  
HDMI  
OUT  
IN  
3
IN  
2
IN  
1
SYSTEM  
後面板  
HDMI輸出  
配備HDMI/DVI的設備  
附註  
1 僅限使用配備 DVI DVI 與高頻寬數位內容保護 (HDCP)相容的設備進行 HDMI 連接。如果您選擇連DVI 接頭,您需要一個獨立的轉接器  
DVIHDMI  
本機設計符合  
DVD  
連接不支援音訊訊號需詳細資訊,請洽詢當地的音訊裝置經銷商。  
)才能進行連接。但  
HDMI  
1.3a  
DVI  
HDMI 1.0  
連接是否導致傳送不可靠的訊息視您連接的設備而使用配備  
(高傳真多媒體介面)  
版。使用  
版功能的  
設備時,無法HDMI 連接輸出防盜拷控DVD-Audio CPPM 音源。  
SACD Dolby Digital Plus Dolby TrueHD DTS-HD Master Audio  
本機支援  
。若要運用這些格式,請確定連接至本機的設備也支援相應的格式。  
35  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
08  
其他接線  
1
HDMI  
使用  
連接線,將本接收重低音揚聲器的  
ENTER  
HDMI IN 1  
出插孔。  
3 HDMI HDMI  
至 內部接線連接至  
設備的  
3
4
HDMI Mode ENTER  
然後按下 。  
「  
將本接收重低音揚聲器連接至您HDMI 設備後,在您  
HDMI 內容示裝置上的 HDMI 指示燈(紅色)  
亮起。  
ENTER  
調整設定值,然後按下  
-輸出來自本機的  
確認。  
ENTER  
音訊訊號。  
AMP Mode  
HDMI  
-輸出來自一般電視機或電漿電視  
2 使HDMI 連接線,將本接收重低音揚聲器的  
HDMI OUT 內部接線連接HDMI 相容顯示裝置的  
Through Mode  
音訊訊號。  
HDMI  
內部接線。  
連接線接頭上的箭頭應該朝右,與播放器的接頭對  
HDMI  
指示燈亮起。  
HDMI THROUGH  
齊。  
HDMI  
關於  
HDMI (高傳真多媒體介面)視訊支援單一數位連接的  
視訊與音訊,可搭配 DVD 播放器、DTV、機上盒與其他  
影音裝置使用HDMI 的開發是為了以單一規格提供高  
頻寬數位內容保護 (HDCP)與數位影像介面 (DVI)技  
HDCP 用於保DVI 相容顯示器傳送和接收的數位  
內容。  
使用  
至 按鍵選擇您要連接的  
3
)。  
輸入  
3
HDMI 1  
HDMI  
(例如  
HDMI 2  
您可以使用顯示裝置的  
執行此操作。  
INPUT SELECTOR  
如果想要聽到您的電視機或電漿電視輸出的  
HDMI  
環繞聲音效的功能。  
+
有支援標準、增強或高傳真視訊 標準到多聲道  
HDMI  
本接收重低音揚聲器將不會輸出任何聲音,  
HDMI  
功能包括解壓縮視訊、高達  
2.2 GB  
每秒  
個接頭在影音來源與  
標誌及  
的頻寬、一個接取代多條連接線和多  
在下文的  
模式設定 中將  
模式設定為  
HDMI  
HDMI  
DTV  
等影音裝置之間通訊。  
High-Definition Multimedia  
的商標或註冊商標。  
HDMI Licensing LLC  
Through Mode  
HDMI HDMI  
均為  
如果視訊未出現在電視機或電漿電視上,請嘗試調  
整您的設備或顯示器上的解析度設定。  
Interface  
模式設定  
HDMI  
HDMI 音訊的傳送路徑是來自接收重低音揚聲器  
(擴大器)或經由電視機或電漿電視。HDMI 模式設定為  
Through Mode 時,無法使用多個本機的聲音功能。  
重要  
RCV  
按下可將遙控器設定為可操作接收重低音揚聲  
器的接收控制模確定液晶螢幕顯示  
畫面。  
RECEIVER  
SETUP  
1
2
SETUP。  
ENTER  
HDMI Setup然後按ENTER。  
36  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HDMI Control  
09  
第 章  
9
HDMI Control  
使用  
電漿電視或硬碟  
連接線將本機連接至  
相容先鋒  
HDMI Control  
錄影機後,您可以透過所連接電  
HDMI  
/DVD  
進行  
連接  
HDMI Control  
漿電視的遙控器控制本機,以及讓所連接的電漿電視自  
動變更輸入以回應在本機上執行的操作。  
您可以對連接的電漿電視和最多三個其他設包括最  
多兩台錄影機或播放器。  
如需有關透HDMI 連接線連接可執行哪些操作的詳細  
資訊,請參閱電漿電視的操作手冊。  
確定將電漿電視的音訊連接線連接至本機的音訊輸入插  
孔。  
您無法使用此功能搭配不支HDMI Control 功能的  
設備。  
如果您使用市售HDMI 連接線,請檢查該連接線是  
否支HDMI 1.3 標準。否則,HDMI Control 功能可  
能無法正常作用。  
HDMI  
我們不保證本機可以搭配非先鋒公司製造的  
Control  
相容設備使用。  
重要  
RCV  
HDMI Control相容的  
先鋒硬碟/DVD錄影機,  
Blu-ray disc播放機或DVD播放器  
按下可將遙控器設定為操作接收重低音揚聲器  
的接收控制模確定液晶螢幕顯示以下所示的  
HDMI輸出  
RECEIVER 畫面。  
RECEIVER  
接收重低音揚聲器  
側面板  
ADV  
F.S.  
SURR  
後面板  
SURR SURR  
HDMI  
OUT  
IN  
3
IN  
2
IN  
1
ANTENNA  
L
AM LOOP  
IN  
1
IN  
2
R
OPTICAL  
DIGITAL  
FM  
UNBAL 75  
ANALOG  
AUDIO IN  
SYSTEM  
從數位音訊  
輸出(光學)  
從音訊輸出  
HDMI輸入  
HDMI Control相容的  
先鋒電漿電視  
37  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HDMI Control  
09  
將電漿電視直接連接至本機。中斷與其他擴大器或  
HDMI  
重要  
影音轉換例如  
致操作上的錯誤。  
開關)的直接連接可能導  
對此系統進行接線或變更接線時,請務必關閉電源,  
並將電源線插頭自牆上電源插座上拔除。完成所有  
接線後,再將電源線插頭接上電源插座。  
將本機連接至  
電源插座始  
秒的初始化程  
15  
AC  
序。初始化期間不可以執行任何操作。顯示裝置上  
指示燈在初始化期間閃爍,您可以在此指  
HDMI Control相容的  
先鋒電漿電視  
HDMI  
示燈一停止閃爍時即開啟本機電源。  
HDMI輸入  
若要使本功能發揮最大效建議您不要HDMI 設  
備連接至電漿電視,而是直接連接至本機HDMI  
端子。  
HDMI連接線  
HDMI輸出  
其他擴大器  
或影音轉換器  
HDMI輸入  
HDMI連接線  
HDMI OUT  
HDMI 選項  
若要充分運動 HDMI Control 功能,您必須調整本機的設  
定與 HDMI Control 相容連接設備。如需詳細資訊,請參  
閱每個設備的操作手冊。  
接收重低音揚聲器  
HDMI Control 模式  
僅限連接您打算做為本HDMI 輸入來源的設中  
斷與其他擴大器或影音轉換HDMI 開關)  
的直接連接可能導致操作上的錯誤。  
選擇是否將本機的  
功能設定為  
HDMI Control  
功能,必須將它設定為  
HDMI Control  
On  
。若要使用  
Off  
Control On  
使用非先鋒製造的電視機時,將此設定切換至  
Control Off  
SETUP  
按下  
1
2
3
4
SETUP  
HDMI Control相容的  
先鋒電漿電視  
HDMI輸入  
ENTER  
ENTER  
ENTER  
「  
「  
然後按下  
ENTER  
HDMI Setup  
HDMI連接線  
HDMI OUT  
接收重低音  
揚聲器  
然後按下  
HDMI Ctrl  
ENTER  
調整設定值,然後按下  
確認。  
ENTER  
HDMI IN  
HDMI  
-啟用  
功能。在本機電源  
Control On  
關閉,且在使用  
HDMI Control  
功能期間開始播放支  
HDMI Control  
HDMI輸出  
連接線  
援的來源時,從電漿電視輸出來自  
連接的音  
HDMI  
無法使用  
HDMI Control  
其他擴大器或影音轉換器  
訊與視訊。  
-已停用  
Control Off  
同步化操作。本機電源關閉後,不會輸出透過  
連接的音訊和視訊來源。  
HDMI  
38  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HDMI Control  
09  
設定自動延遲  
HDMI  
本功能自動修正以  
連接的設備之間的音訊至視訊  
HDMI  
使用同步化之前  
完成所有連接與設定後,您必須:  
延遲。音訊延遲時間的設定是以  
連接線連接的顯  
示器操作狀態而定。本機根據視訊延遲時間自動調整音  
訊延遲時間。  
1
2
使所有設備進入待機模式。  
開啟所有設備的電源,但在最後才開啟電漿電視的  
SETUP  
1
2
3
4
SETUP。  
電源。  
3 選擇電視機與本機連接HDMI 輸入,然後查看來  
自連接設備的視訊輸出是否正常顯示在螢幕上。  
ENTER  
ENTER  
ENTER  
HDMI Setup然後按ENTER。  
Auto Delay然後按ENTER。  
同步化擴大器模式  
同步化擴大器模式在您執行電漿電視的操作時開始。如  
需詳細資訊,請參閱電漿電視的操作手冊。  
A.Delay On  
「  
A.Delay Off  
,  
然後按ENTER 以確認。  
同步化擴大器模式操作  
使HDMI 連接線將設備連接至本機後,您可以使用同  
步化擴大器模式來同步化下列操作:  
提示  
本功能僅在連接的顯示器支援適用於  
HDMI HDMI  
使本機靜音或調整本機音量時,顯示在電漿電視上。  
連接的設備開始播放時,自動變更本機的輸入。  
的自動音訊/視訊同步化功唇形同步)  
Control  
時才能使用。如果您找到不適當的自動設定延遲時  
即使您將本機的的輸入變更為不是以  
置,同步化擴大器模式仍然有效。  
連接的裝  
HDMI  
間,將  
設定為  
。  
,然後手動調整聲音延  
Off  
A.Delay  
遲設第  
27  
在聆聽來自硬碟  
錄影機的音源時下  
GENRE  
/DVD  
可自動選擇最適合的聆聽模第  
。  
26  
TV  
電漿電視的音訊輸入設定 ( 輸入)  
若要使用本裝置收聽來自電漿電視的音效,您必須接上  
HDMI 連接線以外的音訊連接線。在此選單中,將音訊  
輸入設定為您想要連接的音訊輸入。按下遙控器上的 TV  
將本機切換至在此選擇的輸入來源。此設定值變成所選  
擇的輸入,並且從本裝置輸出來自電漿電視的音效。  
取消同步化擴大器模式  
如果您在透過  
連接至電漿電視或觀賞電視節目時  
HDMI  
取消同步化擴大器模式,本機電源關閉。  
選擇來自  
Digital 1 Digital 2  
的輸入。  
Analog  
SETUP  
1
SETUP。  
ENTER  
2
System Setup然後按ENTER。  
ENTER  
然後按下  
TV Input  
ENTER  
3
ENTER  
調整設定值,然後按下  
確認。  
ENTER  
4
重要  
您必須設定此設定值才能啟動  
功能。  
HDMI Control  
39  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
其他資訊  
第 章  
10  
其他資訊  
重要  
設定遙控器以控制電視機  
您可以使用隨附的遙控器操控電視機。若要使用此功  
能,您必須先使用下頁表中的標記碼設定遙控器。  
RCV  
按下可將遙控器設定為操作接收重低音揚聲器  
的接收控制模確定液晶螢幕顯示以下所示的  
畫面。  
RECEIVER  
TV  
1
2
將輸入設定為電視機。  
TV SETUP  
RECEIVER  
按住  
按鍵,然後按下  
ADV  
F.S.  
電視機預設畫面顯示在遙控器上,而目前製造商代碼顯  
示在液晶螢幕上。  
SURR  
SURR SURR  
TV PRESET  
3 5 1  
2
製造商代碼  
數字按鍵  
ENTER  
調暗顯示幕亮度  
若您覺得太亮,可調暗顯示裝置的顯示亮度。  
1
1
3
SETUP  
1
2
3
4
SETUP。  
4
7
5
6
9
8
ENTER  
ENTER  
ENTER  
System Setup然後按ENTER。  
CLEAR  
ENTER  
0
EXIT  
「  
然後按下  
ENTER  
Dimmer  
3 使用數字按鍵輸入電視機的製造商代碼,然後按  
ENTER。  
關於製造商代碼清單,請參閱下一頁的表格果提供  
您的電視機一個以上的製造商代碼,請輸入清單中的第  
一個。  
「  
「  
」,  
Dimmer Light  
以確認。  
Dimmer Dark  
然後按下  
ENTER  
若表中沒有您電視機的製造商名稱,則無法使用此  
遙控器操控電視機。  
設定睡眠定時器  
睡眠定時器經過特定時間後將會切斷接收重低音的電  
源,您可放心入睡。  
將遙控器對準電視機,按下  
,確認遙控  
SOURCE  
4
器是否可用。  
若遙控器的設定正確,電視機應會關機未關機,且  
出現其他標記,請使用新代碼並重複步驟 。  
1
SLEEP  
按下可選擇選項。  
有以下選項可供選擇:  
-約一小時後關閉電源  
Sleep On  
Sleep Off -取消睡眠定時器  
Sleep On 後,再按一SLEEP 可檢查剩餘的時  
間。每條線代表12 剩餘時間:  
S l e e p - - - - -  
附註  
1
設定睡眠定時器時,不論此設定值為何,顯示裝置的顯示幕都會變暗。  
40  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
其他資訊  
電視機預設代碼表  
請注意,指定正確預設代碼後,可能只有特定功能可供控制,或者表中的製造商代碼無法用於您目前的機種。  
製造商代碼  
製造商代碼  
Admiral 003, 004, 005  
Aiwa 006, 007, 008  
Akai 009, 010  
Alba 011  
NEC 128, 129, 130, 131  
Nokia 086, 087, 132, 133, 134  
Nokia Oceanic 135, 136  
Nordmende 137, 138, 139  
AOC 012  
Okano 140  
Onwa 141  
Orion 142  
Bell&Howell 013, 014  
Bestar 015  
Blaupunkt 016, 017  
Blue sky 018  
Panasonic 143, 144, 145, 146, 147, 148, 149, 150  
Philco 151, 152, 153  
Philips 154, 155, 156  
Phonola 157  
Portland 158, 159  
Proscan 160  
Brandt 019  
Brocsonic 020, 021  
Bush 022  
Clatronic 023  
Craig 024, 025, 026, 027  
Croslex 028  
Quasar 161, 162  
Radio 163  
Curtis Mathis 029, 030, 031  
Radio Shack 164, 165, 166, 167  
Radiola 168  
Daewoo 032, 033, 034, 035, 036, 037  
Daytron 038  
Dual 039, 040  
RCA 169, 170, 171, 172, 173, 174, 175  
SABA 176, 177, 178, 179, 180  
Samsung 181, 182, 183, 184, 185, 186, 187, 188  
Sanyo 189, 190, 191, 192, 193, 194, 195, 196, 197, 198  
Schneider 199, 200, 201, 202  
Scott 203, 204  
Emerson 041, 042, 043, 044, 045, 046, 047  
Ferguson 048, 049, 050  
First line 051  
Fisher 052, 053  
Fraba 054  
Sharp 205, 206, 207, 208, 209, 210, 211  
Siemens 212  
Fujitsu General 055  
Funai 056, 057, 058, 059, 060  
Signature 213, 214  
Sony 215, 216  
GE 061, 062, 063, 064, 065  
Goldstar 066, 067, 068, 069, 070  
Goodmans 071, 072, 073  
Grundig 074, 075, 076  
Hitachi 077, 078, 079, 080, 081, 082  
HYUNDAI 083  
ICE 084  
Irradio 085  
Itt 086, 087  
JC Penny 088, 089, 090, 091  
JVC 092, 093, 094, 095, 096, 097  
Kendo 098  
KTV 099, 100, 101  
LG 102  
Loewe 103, 104, 105  
LXI 106, 107, 108, 109, 110, 111  
Sylvania 217, 218, 219  
Symphonic 220  
Tatung 221  
Telefunken 222, 223, 224, 225  
Thomson 226, 227  
Thorn 228  
Toshiba 229, 230, 231, 232, 233, 234  
Universum 235  
Videch 236, 237, 238  
W.Whouse 239  
Wards 240, 241, 242, 243  
Watson 244  
Yamaha 245, 246, 247, 248, 249  
Zenith 250, 251  
PIONEER 001, 002  
Magnavox 112, 113, 114, 115  
Mark 116  
Matsui 117, 118  
Medion 119  
Mitsubishi 120, 121, 122, 123, 124, 125, 126  
Mivar 127  
41  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
其他資訊  
重設系統  
使用此程序可將所有系統設定值恢復至出廠設定。  
環繞音效格式  
以下是您在 DVD 上可以找到的有DVD、衛星接收器、  
連接線、陸地廣播和錄影帶的主要環繞聲格式簡要說。  
1
2
開啟系統電源。  
按住  
,然後按下顯示裝置上的  
Dolby  
INPUT SELECTOR  
按鍵。  
下次開啟電源時,所有系統的設定值都會重新設定。  
STANDBY/ON  
Dolby 技術的說明如下所示需詳細資訊,請造訪  
安裝與維護  
安裝提示  
Dolby Digital  
我們希望您能夠在日後享受本系統所帶來的樂趣,因此  
選擇安裝地點時,請記住以下要點:  
為電影院和家中播放  
與數位廣播音軌  
DVD  
Dolby Digital  
常用的多聲道數位音訊編碼技術。它提供六個獨立的聲  
道,由五個全音域聲道和一個主要供深沈、隆隆的音效  
請⋯  
在通風良好的房間內使用本系統。  
使用的特殊  
(低頻率效果)聲道所組成,因此成為  
聲道」一詞的由來。  
LFE  
將本系統放在穩固、平坦的水平面,如桌子、置物櫃或音  
Dolby Digital 5.1  
響架上  
除了上述的格式特點之外,  
解碼器提供與  
Dolby Digital  
單音、立體聲和來自多種位元率與聲道的  
Dolby Pro  
請勿⋯  
於高溫或濕氣重的地方使用本系統,包括放射物及其他會  
產生熱源的電器產品。  
音訊相容的縮混功能。另一個特點稱為  
Logic  
Dialog  
(對話正常化本特點根據相對於其峰  
Normalization  
值位準的節目中之平均位準來減小節目的聲音,以便達  
將本系統放在窗台或其他可能受陽光直射之處。  
在灰塵過多或過於潮濕的環境中使用本系統。  
將本系統直接放在擴大器上方,或放在其他使用時會變熱  
的立體聲系統裝置上。  
到一致的播放位準。  
Dolby Pro Logic II Dolby Surround  
在電視機或顯示器附近使用本系統,否則可能會產生干擾  
-尤其是使用室內天線的電視機。  
(和  
Dolby Pro  
Dolby Pro Logic IIx  
解碼系統的改良版。由於採用創新動向邏  
Logic  
Dolby Pro Logic II  
在廚房或其他可能使系統暴露於油煙或蒸氣的地方使用本  
系統。  
輯」電路,本系統可以從以下的來源中擷取出環繞音  
效:  
將本系統放在厚重的地毯上或用布蓋住-以免阻礙系統的  
散熱。  
-取自任何立體聲來源之 聲道音  
4.1  
Dolby Pro Logic  
單聲道)  
將系統放在不平穩的表面,或其他面積無法支撐系統四個  
腳架的表面上。  
-取自任何立體聲來源之  
Dolby Pro Logic II  
立體環繞聲)  
聲道  
5.1  
使用雙聲道來源時,由接收重低音揚聲器中的低音管理  
產生 「.1」重低音聲道  
Dolby Surround 是在立體聲音軌內嵌入環繞聲資訊的編  
系統,Dolby Pro Logic 解碼器使用此系統提供更細緻  
的增強環繞聲聆聽效果。  
Dolby Digital Plus  
Dolby Digital Plus 是使用於所有高傳真節目和媒體的下  
一代音訊技術。這種技術結合了效率,以符合未來需要  
強大功能與使用彈性的廣播需求,落實了未來高傳真世  
代中所期待的全方位音效潛力。Dolby Digital Plus 以全球  
DVD HD 廣播的多聲道標Dolby Digital 為建立基  
礎,並針對下一代的影音接收器而設計,但仍然能與目  
前所有的影音接收器相容。  
42  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
其他資訊  
DTS-ES  
Dolby Digital Plus  
編序能力,並以最大可能的  
7.1  
6 Mbps  
*
提供多達  
的多聲道音訊  
HD  
潛在位元率、  
DTS-ES ES  
DTS-ES  
DTS-ES Matrix 6.1  
編碼來源解碼的解碼  
代表擴展環繞聲)是一種可以將  
DVD  
3 Mbps  
1.7 Mbps BD  
和藍光碟片上高達  
上高達  
Discrete 6.1  
的最大位元率效能支援單一編碼位元率中的多種編序,  
Dolby Digital  
DTS-ES Discrete 6.1  
器。  
以完全分獨立)的環繞聲  
DTS-ES Matrix 6.1  
聲道聲音。  
並且在現有的  
Dolby Digital  
系統上輸出用於播放的  
Dolby Digital Plus  
6.1  
後聲道提供「真實的」  
位元流。  
指揮和製作人想要的原音。  
它也擁有具備獨立聲道輸出的多聲道音效、互動式混音  
與先進系統中的串流功能。高傳真多媒體介(  
可以精準地重現  
擁有與環繞聲左/右聲道形成矩陣的環繞聲後聲道。這  
DTS 5.1  
兩種音源都與傳統的  
聲道解碼器相容。  
DTS Neo:6  
HDMI  
支援的單線式數位連接可用於高傳真音訊和視訊。  
DTS Neo:6  
視訊或電視)與  
可以產生取自任何矩陣式立體聲音例如  
5.1  
6.1  
聲道環繞聲。而且  
聲道音源的  
Dolby TrueHD  
它使用已編碼在音源中的聲道資訊,並自行處理以判斷  
聲道的定使用雙聲道來源時,由接收重低音揚聲器  
是針對下個世代的高傳真光碟片而開發的  
Dolby TrueHD  
新一代無損失編碼技術。  
位元等級媲美錄音室製作的聲音,並以下一代的高傳真  
.1  
中的低音管理產重低音聲道如果使用兩個  
聲道來源,使用  
音樂。  
帶來震撼人心且  
Dolby TrueHD  
DTS Neo:6  
時提供兩個模電影院與  
光碟片傳達出真實的高傳真娛樂體驗。結合高傳真視訊  
時,  
以令人驚豔的音效和高傳真影像,提  
Dolby TrueHD  
供前所未有的家庭電影院體驗。  
它支援高達 的位元率,而且可錄製高達八個全  
DTS 96/24  
是原始  
DTS Digital Surround  
解碼器提供高品質  
的延伸,使用  
位元音此格  
DTS 96/24  
DTS 96/24  
18 Mbps  
音域聲每個聲道都是  
96 kHz/24  
位元 音訊。  
/96 kHz  
*
24  
它擁有廣泛的中繼資料,包括對話正常化和動態範圍控  
制。高傳真多媒體介支援的單線式數位連  
式也完全向後相容於所有目前的解碼器。這表示  
DVD  
聲道解碼器播放此軟體。  
放器可以使用傳統的  
DTS 5.1  
HDMI  
接可用於高傳真音訊和視訊。  
DTS-EXPRESS  
是一種低位元率解碼技術,支援固定資料  
DTS-EXPRESS  
傳輸率的  
碟片的次要音訊整合,對將來的廣播和記憶音訊內容提  
* HD DVD 和藍光碟片標準目前將它們的最大聲道數限  
制在八個,Dolby Digital Plus Dolby TrueHD 支援  
超過八個聲道。  
聲道。此格格與  
的子音訊和藍光  
HD DVD  
5.1  
升潛在的適用性。  
Dolby Laboratories 授權製造杜比Dolby、  
DTS-HD Master Audio  
Pro Logic」和D 標誌Dolby Laboratories 的商標。  
技術為聆聽者帶來在專業錄音室  
DTS-HD Master Audio  
中錄製的主要音源,不但未損失任何資料且保留了音  
質。 採用可變資料傳輸率,以遠超  
DTS  
Dolby  
技術的說明如下所示。如需詳細資訊,請造訪網站  
DTS-HD Master Audio  
過標準 的藍光碟片格最大傳輸率  
DVD  
最大傳輸率  
24.5 Mbps  
)的速率傳送  
18.0 Mbps  
HD-DVD  
資料。這些高資料傳輸速率在沒有任何資料損失的情況  
下傳送 位元的 聲道音源,而且完全無損  
96 kHz/24 7.1  
DTS-HD Master Audio  
及原始的音。  
技術,它可以依音樂或影片創作人的需要完整重現出真  
是一種無可取代的  
DTS Digital Surround  
是來自  
聲道音訊編  
5.1  
DTS Digital Surround  
碼系統,目前廣泛使用於  
DTS Inc.  
實的聲音。  
DVD-Video DVD-Audio 5.1  
聲道音樂碟片、數位廣播和電視遊戲。它可以提供六個  
”是  
DTS  
的註冊商標“  
的商標。  
DTS, Inc.  
DTS, Inc.  
DTS-HD Master  
”是  
Audio  
獨立的聲道,由五個全音域聲道加上一個 聲道所組  
LFE  
成。使用低壓縮率得到較好的音質,並在播放時以較高  
的速率傳送聲音。  
43  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
其他資訊  
故障排除  
人們經常錯將不正確之操作當成系統故障或異常。如果您認為本機有任何異常之處,請按以下各點進行檢查。有時  
候問題可能出在其他設備上。請仔細檢查其他使用中的設備和電器。如果在檢查以下各點後仍無法改善問題,請就  
近洽詢您的先鋒授權服務中心或經銷商,前來代為維修。  
如果本系統是因為受到靜電等外來效應致無法正常操作,請將電源插頭從輸出插座上拔下再插回去,以回復正常  
的操作狀態。  
若是與音效相關的問題,請也一併檢查音效播放裝置的設定。如需詳細資訊,請參閱裝置的操作手冊。  
一般  
問題  
解決辦法  
電源無法開啟或突然關機 (啟 接通本機電源,等待一分鐘,然後重新開機。  
動時可能顯示一錯誤訊息。  
或顯示幕突然熄滅,而且沒有  
輸出任何聲POWER ON  
指示燈亮藍色)和 HDMI  
指示燈亮紅色。  
確定主機上的線束無鬆脫的情形有鬆脫,可能會造成系統自動關機。  
檢查揚聲器連接是否正確。  
請確定接收重低音周圍是否有足夠的通風空間。  
確定主電源的電壓確實適用於本機種。  
試著降低音量。  
如果仍無法解決問題,請將本機攜至最近的先鋒授權服務中心或您的經銷商處接受維  
修。  
請勿堵住底部的進氣口和本機背面的排氣口。  
選擇輸入功能後,沒有聲音輸  
出。  
如果您正在使用線路輸入插孔,請確定設備的接線方式正確並調整外部設備 (例如可  
攜式播放器)的音量 (請參閱第  
頁上的連接輔助設。  
33  
調高音量。  
模式設定為  
(第  
本機連接的揚聲器沒有輸出任何聲  
36  
HDMI  
Through Mode  
音。  
HDMI  
DVI  
連接 設備後,沒有輸出任何聲音。  
使用  
MUTE  
按下遙控器上的  
以關閉靜音功能。  
30  
頁上的聲道位準設定以檢查揚聲器位準。  
環繞聲揚聲器未輸出任何聲  
音。  
請參第  
Stereo  
正確地將揚聲器接上 (請參閱第 頁上的接線。  
24  
頁上的以環繞音效聆聽。  
檢查您是否選擇  
請參第  
8
使用光學數位連接線連接外部設備時,檢查外部設備的音訊輸出與 HDMI 設定。  
無法使用遙控器進行操控。  
更換電池 (請參閱21 頁上的裝入遙控器電。  
請在 7 m 內的範圍,30° 的角度對準遙控感應器操作 (請參閱22 頁上的使用遙控  
。  
移除障礙物或從其他位置操作。  
避免前面板上的遙控感應器受到陽光直射。  
操作連接至 CONTROL OUT 插孔的其他先鋒設備時,請確定已接上控制連接線和 HDMI  
或類比音訊連接線 (第  
。  
35  
44  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
其他資訊  
調諧器  
問題  
解決辦法  
收聽電台廣播時有明顯的雜  
音。  
請接上 AM 請參閱8 頁上接線加以調整方向及位得到最佳的接收  
效果也可以另外接一條內部或外部 AM 請參35 頁上的連接外接天線。  
完全伸展開 FM 線型天線,調整最佳接收的位置,然後固定於牆上也可以另外接一  
組外接 FM 請參35 頁上的連接外接天線。  
關閉其他可能造成雜訊的設備或將其移走。  
調諧間隔不適用於您所在國家或地區。若要切換調諧間隔參閱第 29 頁上改變頻率  
。  
自動調諧功能無法接收到某些  
電台。  
電台訊號微弱動調諧功能僅能偵測到訊號發射良好的無線電台要獲得更加靈敏  
的調諧條件,可接上一組室外天線。  
HDMI  
故障現象  
解決辦法  
沒有影像或聲音。  
本接收重低音揚聲器是 HDCP 相容設備查您正在連接的設備是否為 HDCP 相容設  
備。  
是否可以搭配本接收重低音揚聲器使用 (即使HDCP 相容設備)視連接的來源設備  
而定。  
如果將  
設備直接連接至顯示器時,問題仍然存在,請參閱設備或顯示器的手冊,  
HDMI  
或聯絡製造商以尋求支援。  
沒有聲音,或聲音突然消失。  
檢查  
模式是否設定為  
HDMI  
AMP Mode/Through Mode  
如果設備是  
DVI  
檢查來源設備的音訊輸出設定。  
裝置,請使用另外的連接方式連接音訊。  
45  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
其他資訊  
顯示的訊息  
訊息  
說明  
192kHz PCM  
SACD  
這些訊息在您操作與正在播放的音訊來源不相容的功能時顯示。  
DTS-HD  
DTS Express  
Dolby TrueHD  
Dolby D+  
No MIC  
未接上 MCACC 設定麥克風時,按下 MCACC 會顯示本訊息。  
本機靜音時,按下 TEST TONE MCACC 會顯示本訊息。  
操作僅適用於雙聲道來源,因目前來源為多聲道來源而無法進行。  
此訊息會在選單閒置一段時間後自動退出時出現。  
Muting  
2ch Only  
Exit  
HDMI Through  
Unknow  
HDMI 模式變為直通模式時,變更聆聲模式、音量或某些聲音設定會顯示本訊息。  
無法取得硬碟 /DVD 錄影機正在播放內容的類型資訊。  
未設定硬碟 /DVD 錄影機正在播放內容的類型。  
No Genre  
HDMI C.ERR 2C*  
Can’t use  
連接的設備與同步化類型模式不相容。  
您嘗試對不支援的此功能的來源設備使用類型同步化模式。  
來源設備正處於無法使用類型同步化模式的情況。  
您嘗試在本機輸入來源是  
操作因環繞聲設定而遭到禁止。  
以外的來源時使用類型同步化模式。  
HDMI  
音量超過  
時,有些功能會受到限制。  
51  
HDMI C.ERR 1**  
檢查連接  
連接線的方式是否正如果連接的方式正確,表示本機可能已損如  
HDMI  
果發生這種情況,請洽詢先鋒授權服務中心或就近的經銷商。  
Noisy!  
MCACC  
因背景雜音太大而無法順利完成  
設定。  
Error MIC!  
Error Speaker!  
Over Temp  
MCACC  
MCACC  
設定期間,因未將麥克風接上或連接不正確而發生錯誤。  
設定期間,因未將揚聲器接上或連接不正確而發生錯誤。  
請降低音量果拔下電源線再重新插入後無法解決這個問題,表示本機可能已損壞。  
如果發生這種情況,請洽詢先鋒授權服務中心或就近的經銷商。  
OC Error1  
OC Error2  
檢查揚聲器連接線是否短路果本錯誤訊息持續顯示,相關維修事宜請洽詢您的先鋒  
授權服務中心或經銷商。  
*** BackUpERR  
相關維修事宜請洽詢您的先鋒授權服務中心或經銷商。  
46  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
其他資訊  
SSP-LX70ST 衛星揚聲器  
規格  
(前置/中置揚聲器  
x2,環繞聲揚聲x2)  
前置/中置揚聲器  
音效多聲道接收重低音  
音箱  
封閉式書架型  
(防磁)  
,單向系統  
圓錐型  
x3  
SX-LX70W  
. . . . . . . . . . . . . . . . . . . . . . . . . . . .  
擴大器部分  
RMS 功率輸8 聲道輸出:  
L/R. . . . . . . . . . . . . . .100 W 50 W+ 50 W)  
1 kHz10 % T.H.D.8 )  
雙重中CL/CR. . . . . . . . .100 W 50 W+ 50 W)  
1 kHz10 % T.H.D.8 )  
環繞L/R. . . . . . . . . . . . . .100 W 50 W+ 50 W)  
1 kHz10 % T.H.D.8 )  
系統  
揚聲器  
. . . . . . . . . . . . . . . . . . . . . . . . . 5.2 cm  
. . . . . . . . . . . . . . . . . . . . . . . . . 5.2 cm  
阻抗  
前聲道  
中央聲道  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Ω  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Ω  
頻率範圍  
. . . . . . . . . . . . . . . . . . . . . . . 200 Hz  
最大輸入功率  
前聲道  
20 kHz  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 W  
中央聲道  
雙重低雙聲道. . . . . . . . .100 W 50 W+ 50 W)  
100 Hz10 % T.H.D.8 )  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 W  
(寬) (高) (深)  
尺寸  
重量  
. . . .122.5 mm  
x89.5 mm  
x104 mm  
FM  
調諧器部分  
頻率範圍. . . . . . . . . . . . . . . . . . . 87.5 MHz 108 MHz  
天線 . . . . . . . . . . . . . . . . . . . . . . . . . . .75 ,不平衡式  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.5 kg  
環繞聲揚聲器  
音箱  
封閉式書架型  
(防磁)  
. . . . . . . . . . . . . . . . . . . . . . . . . . . .  
調諧器部分  
AM  
頻率範圍  
系統  
,單向系統  
. . . . . . . . . . . . . . . . . . . . . . . . . 5.2 cm  
9 kHz 間隔 . . . . . . . . . . . . . . . . 531 kHz 1602 kHz  
10 kHz 間隔 . . . . . . . . . . . . . . . 530 kHz 1700 kHz  
天線 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 迴路天線  
揚聲器  
阻抗  
圓錐型  
x2  
. . . . . . . . . . . . . . . . . . . . . . . . . 5.2 cm  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Ω  
頻率範圍  
. . . . . . . . . . . . . . . . . . . . . . . 200 Hz  
20 kHz  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 W  
(寬) (高) (深)  
最大輸入功率  
重低音部分  
音箱 . . . . . . . . . . . . . . . . . . . . . . . . . . 低音反射落地型  
(防磁)  
尺寸  
重量  
. . . .122.5 mm  
x89.5 mm  
x104 mm  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.44 kg  
系統 . . . . . . . . . . . . . . . . . . . . . . . . . .18 cm,單向系統  
揚聲器. . . . . . . . . . . . . . . . . . . . . . . . . .18 cm 圓錐x2  
阻抗 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Ω  
頻率範圍. . . . . . . . . . . . . . . . . . . . . . . . 30 Hz 500 Hz  
最大輸入功率 . . . . . . . . . . . . . . . . . . . . . . . . . . 50 W x2  
配件  
配件AS-LX70:  
遙控器  
AA/LR6  
電源線  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
鹼性電池  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3  
輸入/輸出部分  
HDMI 端子  
輸入 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 x3  
輸出 . . . . . . . . . . . . . . . . . . . 19 5 V100 mA)  
其他接頭  
系統接頭. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 接腳  
音訊輸入. . . . . . . . . . . . . . . . . . . . . . . x2 (數位)  
RCA 2 接腳類比)  
控制輸出. . . . . . . . . . . . . . . . . . . . . . . . . . . 迷你插x2  
顯示裝置  
顯示裝置  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
迴路天線  
AM  
FM  
線型天線  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
設定)  
麥克用於自動  
MCACC  
. . . . . . . . . . . . . . . .1  
連接線  
HDMI  
控制連接線  
顯示連接線  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
光學數位連接線 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
iPod 連接. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
本操作手冊  
系統接頭. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 接腳  
前音訊輸. . . . . . . . . . . . . . . . . . . . . . . . . . . 迷你插孔  
MCACC 輸入 . . . . . . . . . . . . . . . . . . . . . . . . . 迷你插孔  
iPod 輸入. . . . . . . . . . . . . . . 20 12 V420 mA)  
接收重低音揚聲SX-LX70W)包裝箱:  
清潔布. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1  
衛星揚聲SSP-LX70ST)包裝箱:  
揚聲器連接線 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6  
揚聲器支. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
防滑墊. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16  
螺絲 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
其他  
電源需求  
消耗功率  
. . . . . . . . . . AC 110 V  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 W  
240 V 50 Hz/60 Hz  
待機狀態的消耗功率  
. . . . . . . . . . . . . . . . . . . . . 0.39 W HDMI Control  
. . . . . . . . . . . . . . . . . . . . . 0.29 W HDMI Control  
開)  
關)  
備註  
. . . 245 mm  
x409 mm  
x600 mm  
(高) (深)  
尺寸  
重量  
(寬)  
因產品改良,規格與設計如有變更,恕不另行通知。  
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17.8 kg  
日本先鋒公司出版。  
© 2007 日本先鋒公司。  
版權所有。  
47  
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PIONEER CORPORATION  
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan  
PIONEER ELECTRONICS (USA) INC.  
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404  
PIONEER ELECTRONICS OF CANADA, INC.  
300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada TEL: 1-877-283-5901, 905-479-4411  
PIONEER EUROPE NV  
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11  
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.  
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555  
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.  
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300  
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.  
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270  
K002_B_En  
Published by Pioneer Corporation.  
Copyright © 2007 Pioneer Corporation.  
All rights reserved.  
<ARC7765-A>  
Printed in  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Peavey Music Mixer X Eight RT User Manual
Pelco Security Camera c1405M E User Manual
Philips Automobile Accessories 32PFL8404H User Manual
Philips Stereo System MX965 User Manual
Pioneer Flat Panel Television PDP 427CMX User Manual
Pioneer Flat Panel Television PDP LX508A User Manual
Pioneer Musical Toy Instrument DDJ RB User Manual
Planet Technology Telephone VIP 152T User Manual
Polycom IP Phone Soundpoint IP 550 User Manual
ProForm Home Gym PFEL69050 User Manual