Installation and Assembly:
Peerless Ultra-Slim Articulating Mount for Samsung 46"
and 55" C9000 LED displays
Models: SUAC9000
U
C
©
L
US
Max UL Load Capacity: 75 lb (34 kg)
3215 W. North Ave.
•
Melrose Park, IL
•
(800) 865-2112 or (708) 865-8870
•
Fax: (708) 865-2941
•
ISSUED: 10-01-10 SHEET #: 095-9354-3 12-13-10
Download from Www.Somanuals.com. All Manuals Search And Download.
Before you begin, make sure all parts shown are included with your product.
Parts List
Description
Qty. Part #
A wall arm assembly
B upper mounting plate
C lower mounting plate
D wood screw
1
1
1
4
4
1
8
1
3
4
4
4
046-4176
046-4179
046-4180
500-1090
590-0320
560-1133
046-4096
046-4137
560-2004
560-2029
520-2627
520-2592
concrete anchor
security driver
G fastener cap
H cable clip
I short cable tie
J snap caps
E
F
A
10-32 x 1/2" thread forming screw
1/4-20 x 1/2" hex head thread forming
screw
K
L
M4 x 16 mm phillips screw
long cable tie
520-2088
590-2168
M
N
4
2
Parts may appear slightly different than illustrated.
C
K
L
M
B
I
D
E
F
G
H
J
N
ISSUED: 10-01-10 SHEET #: 095-9354-3 12-13-10
3 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation to Wood Stud Wall
WARNING
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all
attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder
is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs.
Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).
Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended.
1
Based on their edges, draw a vertical line down each stud’s center. Center of screen mounting plate will be
2.5" offset from center of outer mounting slot as shown in figure 1.1 or will be 0.19" offset from center of inner
mounting slot as shown in figure 1.2. Place wall arm (A) on wall as template, level, and mark the center of four
mounting holes. Top mounting slot will be X" above the screen center as shown in figure 1.1 and chart 1.
Drill four 5/32" dia. holes to a minimum depth of 2.5". Secure wall arm (A) to wall with four wood screws (D) as
shown in figure 1.2. NOTE: Be sure arrow is pointing up when mounting wall arm (A) to wall as shown in figure
1.1. Level, then tighten all fasteners.
Insert eight fastener caps (G) into wall plate mounting holes.
fig. 1.2
fig. 1.1
2.5"
(64 mm)
0.19"
(5 mm)
ARROW
X"
SCREEN
MOUNTING PLATE
Chart 1
for 46" display
for 55" display
10.7" (272mm)
9.1" (231mm)
= CENTER OF SCREEN
D
G
A
ISSUED: 10-01-10 SHEET #: 095-9354-3 12-13-10
4 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation to Solid Concrete or Cinder Block
WARNING
• When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual
concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount
in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM
C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a
hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all at-
tached hardware and components.
NOTE: Wall arm assembly (A) must be mounted to
1
concrete
wall using inner mounting holes.
1
surface
Make sure that wall arm assembly is level and use
wall plate as a template to mark four mounting holes.
E
Top mounting slot will be X" above the screen center
as shown in figure 1.1 and chart 1 on page 4. Drill
Drill holes and insert anchors (E).
four 5/16" (8 mm) dia. holes to a minimum depth
of 2.5" (64 mm). Insert anchors (E) in holes flush
A
2
F
with wall as shown. Place wall arm assembly over
anchors and secure with wood screws (D). Level,
then tighten all fasteners. Insert eight fastener caps
(G) into mounting holes.
E
D
Place plate (A) over anchors (E) and secure with screws (D).
NOTE: Be sure arrow of label is pointing up when
mounting wall arm assembly (A) to wall as shown in
figure 1.1.
3
WARNING
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
Tighten all fasteners.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Always attach concrete anchors directly to load-
bearing concrete.
SOLID CONCRETE
CINDER BLOCK
• Never attach concrete anchors to concrete covered
with plaster, drywall, or other finishing material.
If mounting to concrete surfaces covered with a
finishing surface is unavoidable (not evaluated by
UL), the finishing surface must be counterbored
as shown below. Be sure concrete anchors do not
pull away from concrete when tightening screws. If
plaster/drywall is thicker than 5/8" (16 mm), custom
fasteners must be supplied by installer (not evaluated
by UL).
E
D
G
INCORRECT
CORRECT
A
concrete
concrete
wall
plate
wall
plate
plaster/
drywall
plaster/
drywall
ISSUED: 10-01-10 SHEET #: 095-9354-3 12-13-10
5 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
• Be sure to carry display upright, from the top and bottom edges, or damage to display may occur.
Follow instruction manual included with display to remove display from stand.
2
Set display on a flat, level surface. Refer to display manufacturer's installation guide for recommended careful
handling. Remove two M4 chrome plated screws from Ultra-Slim wall mount bar. Save all screws. Install eight
standoff screws (included with display) into eight mounting holes on bottom of display.
M5 CHROME SCREWS
DISPLAY
STANDOFFS
WARNING
• Do not assemble mounting plates (B,C) on top of display or damage to display may occur.
Assemble upper mounting plate (B) to lower mounting plate (C) using four 10-32 x 1/2" thread forming screws (K).
Use configuration as shown in figures 3.1 and 3.2. Do not tighten screws (K).
3
B
B
C
C
K
K
FIG. 3.1
FOR 46" DISPLAYS
FIG. 3.2
FOR 55" DISPLAYS
ISSUED: 10-01-10 SHEET #: 095-9354-3 12-13-10
6 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Set control box into lower mount plate (C) and place assembly onto back of display. Adjust upper and lower
mounting plates (B,C) to align top mounting holes with ultra-slim wall mount bar.
4
Secure assembly to back of display by reinstalling two M4 chrome plated screws (included with display) into ultra-
slim wall mount bar, four M4 black phillips screws (included with display) into lower mounting holes of control box,
and four M4 x 16 mm phillips screws (M) into upper mounting holes of control box.
Tighten all fasteners.
ULTRA-SLIM WALL
MOUNT BAR
M4 CHROME SCREWS
DISPLAY
M
M4 BLACK SCREWS
CONTROL
BOX
Install two 1/4-20 x 1/2" thread forming screws (L) into lower mounting plate (C) leaving 1/8" exposed thread as
shown below.
5
C
L
ISSUED: 10-01-10 SHEET #: 095-9354-3 12-13-10
7 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting Flat Panel Screen
WARNING
• Tighten screws so screen brackets are firmly attached to screen. Do not tighten with excessive force. Overtightening
can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to
become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
Hook two 1/4-20 x 1/2" thread forming screws (L) onto top slots of front plate as shown in figure 6.1.
Fasten two 1/4-20 x 1/2" thread forming screws (L) into bottom mounting holes as shown in figure 6.2.
6
Tighten all screws.
FRONT PLATE
fig. 6.1
L
fig. 6.2
ISSUED: 10-01-10 SHEET #: 095-9354-3 12-13-10
8 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Cable Management
Cables may be routed using short cable ties (I).
Use holes on bottom of lower mounting plate (C) with cable ties (I) to secure cables as shown below.
7
I
CABLES
Cables may be routed using cable clip (H).
Slip cable clip (H) onto bottom of center joint as shown in figure 7.1 and secure cables to cable clip using long cable tie
(N) as shown in figure 7.2.
Secure cables to bottom of wall plate using cable tie (N) as shown below.
WALL PLATE
SLOTS
N
CENTER
CABLES
HJOINT
N
CABLES
fig. 7.2
fig. 7.1
ISSUED: 10-01-10 SHEET #: 095-9354-3 12-13-10
9 of 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Roll Adjustment
Adapter plate may be rolled +/- 5°.
Loosen four M6 nylock nuts half a turn, grasp edges of display and roll screen to desired position as shown.
Retighten four M6 nylock nuts and place four snap caps (J) onto M6 nylock nuts.
8
CAUTION
• Do not tighten joint screws. Doing so may cause
damage to screws, greatly reducing its holding
power.
JOINT SCREWS
M6 NYLOCK NUTS
ISSUED: 10-01-10 SHEET #: 095-9354-3 12-13-10
10 of 10
© 2009, Peerless Industries, Inc. All rights reserved.
All other brand and product names are trademarks or registered trademarks of their respective owners.
Download from Www.Somanuals.com. All Manuals Search And Download.
|