Pelco Home Security System Spectra IV User Manual

I N S T A L L A T I O N

Spectra^®IV Series

Spectra^®IV SE Series

In-Ceiling Mount Back Box

C3417M-B (11/06)

Download from Www.Somanuals.com. All Manuals Search And Download.

1. Locate the center point of the mounting location and insert the compass tool. Draw a circle.

2. Cut the circle out of the ceiling.

3. Attach the conduit fitting, lock nut, and safety chain bracket. Install a safety chain/cable (not supplied) that will

support up to 16 pounds (7.3 kg).

4. Open the hinged door to the back box. Push the tab lock towards the wall of the unit and lift the door open. Pull

wiring into the back box through the conduit fitting. Refer to Table A, Table B, and Table C for wiring distances.

5. Install the back box by compressing the spring clips and pushing the back box through the hole. Tighten the screws

until you hear a clicking noise.

Table B. 24 VAC/24VDC Wiring Distances

Table A. Video Coaxial Cable

Requirements

The following are the recommended maximum distances for 24 VAC

and 24 VDC applications and are calculated with a 10 percent voltage

drop. (Ten percent is generally the maximum allowable voltage drop

for AC- or DC-powered devices.)

Cable Type* Maximum Distance

RG59/U

RG6/U

750 ft (229 m)

1,000 ft (305 m)

1,500 ft (457 m)

Wire Gauge

18 AWG 16 AWG

(0.5 mm²) (1.0 mm²) (1.5 mm²) (2.5 mm²)

AC/DC

Total VA/

Total Watts

RG11/U

20 AWG

14 AWG

*Cable requirements:

75 ohms impedance

All-copper center conductor

All-copper braided shield with 95% braid

coverage

23 VA/

15 watts

123 ft

(38 m)

196 ft

(60 m)

311 ft

(95 m)

495 ft

(151 m)

73 VA/

65 watts

39 ft

(12 m)

62 ft

(19 m)

98 ft

(30 m)

156 ft

(48 m)

NOTE: Input power for the dome is 24 VAC or 24 VDC. Using 24 VAC input power, power consumption is 23 VA per dome

for indoor models and 73 VA for outdoor models. Using 24 VDC input power, power consumption is 0.7 A (15 watts) for

indoor models and 3 A (65 watts) for outdoor models.

Use a 24 VAC transformer with the following minimum VA:

40 VA per dome

100 VA per dome

For indoor models (without heater)

For outdoor models (with heater)

Table C. UTP Wiring Distances

Receiver

Maximum Distance

Active

(Video Only)

0-3,000 ft

(0-914.4 m)

Passive

0-750 ft

(0-228.6 m)

(Video, Coaxitron, Pelco V-Sync)

NOTE: As a minimum, UTP requires Cat5, 100-ohm twisted pair cable.

C3417M-B (11/06)

Download from Www.Somanuals.com. All Manuals Search And Download.

ALARMS

AUX1

GND

COM

AUX2

GND

VIDEO

PWR- GND PWR+ RX- RX+ TX- TX+ UTP+ UTP-

C3417M-B (11/06)

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Suspended Ceiling Only: Install the ceiling tile with the back box. Attach a T-rail clip on each side of the ceiling

tile.

WARNING: An electrical short in the back box may occur if the metal BNC connector is not completely covered by

the protective boot.

7. Connect wiring to the circuit board inside the back box. When finished, close the door to the back box and turn on the

power. The green LED will light.

NOTES:

•

Aux 1: Maximum 2 A at low voltage (<40 V)

Aux 2: Maximum 30 mA at 32 VDC

If you are using both unshielded twisted pair (UTP) wiring and a translator board, install the UTP wiring before

installing the translator board.

If you are installing an environmental back box in a railway application, attach a ground wire from the circuit

board power connector to a structural ground using at least 18-gauge wire.

C3417M-B (11/06)

Download from Www.Somanuals.com. All Manuals Search And Download.

SWITCH 1 AND 2

C3417M-B (11/06)

Download from Www.Somanuals.com. All Manuals Search And Download.

8. Configure DIP switches SW1 and SW2 located on the top of the dome drive. For DIP switch settings, refer to the

labels located on the top of the dome drive or to the Switch Settings section.

NOTE: When connecting more than one Spectra^®dome to a single controller, terminate the unit farthest from the

controller. To terminate the dome drive set the SW2-10 switch to the ON position.

9. Install the dome drive. Refer to Table D for a list of compatible dome drives and back boxes. Line up the blue and red

tabs with the blue and red arrows on the hinged door inside the back box. Push in on the tabs. Insert one side and

then the other side. Continue pushing on the ends of the tabs until both sides click into place.

Table D. Spectra Dome Drive and Back Box Compatibility

Back Box

Dome Drive

Spectra II Spectra III Spectra IV

Spectra II^®

Spectra III

Spectra IV

•

™

•

10. Install the lower dome. Snap the clip on the end of the trim ring leash into the hole on the lip of the back box.

Snap the trim ring into the plastic snap washers on the mounting screws.

To use your dome, refer to the operation and programming manual.

C3417M-B (11/06)

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

If your dome does not power up properly after installation, use the following steps.

1. Check the fuse on the circuit board inside the back box for continuity. Replace the fuse if needed.

2. Check the wiring with a volt meter to ensure proper voltage is being received into the back box.

If your dome powers up correctly, but you do not have accurate control, use the following steps.

1. Check the signal with a volt meter or an oscilloscope.

NOTE: This step will not apply if you are using Coaxitron control.

2. Ensure that the switch settings on the dome drive are set correctly. Refer to the Switch Settings section.

3. If you are using a Pelco controller, ensure that the factory-installed 16-pin jumper has not been removed. If you are

using a third-party controller, a TXB Series translator board must be installed. The dome will not function without this

16-pin jumper or a translator board installed.

C3417M-B (11/06)

Download from Www.Somanuals.com. All Manuals Search And Download.

Switch Settings

WARNING: If you are using D-type or P-type control, your system may not operate if the baud rate and address

switches are not set correctly. The switches are set at the factory at the defaults for D-type control (2400 baud and

address 1).

Table E. Switch Settings for SW2

Special Systems

Switch Number

AD-32 Preset System

CM9502 Setting

Vicon

Not currently available; SW2-3 is reserved for future use.

Serial Port Settings

Switch Number

RS422

OFF OFF

RS485, Four Wire

RS485, Two Wire

OFF

D or P Protocol Baud Rate

Switch Number

2400 Baud (Default for D-type Control)

4800 Baud (Default for P-type Control)

9600 Baud

OFF OFF OFF

OFF OFF

OFF

Video Cable Type

Switch Number

Coax Cable

OFF

UTP Cable

Dome Termination

Switch Number

Terminated

OFF

Not Terminated

C3417M-B (11/06)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table F. Switch Settings for SW1, P-Type Control

NOTE: For Coaxitron controls, SW1 is not used; set all switches OFF. For D-type control systems, refer to Table G.

SWITCH SETTING

SPECTRA

ADDRESS

SPECTRA

ADDRESS

SW1-1

OFF

SW1-2

SW1-3

OFF

SW1-4

SW1-5

OFF

SW1-1

OFF

SW1-2

SW1-3

OFF

SW1-4

SW1-5

OFF

Table G. Switch Settings for SW1, D-Type Control

NOTE: For Coaxitron controls, SW1 is not used; set all switches OFF. For P-type control systems, refer to Table F.

SWITCH SETTING

SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

SWITCH SETTING

SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

SPECTRA

ADDRESS

SPECTRA

ADDRESS

OFF

C3417M-B (11/06)

Download from Www.Somanuals.com. All Manuals Search And Download.

SWITCH SETTING

SPECTRA

ADDRESS

SPECTRA

ADDRESS

SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

OFF

100

101

102

103

104

105

106

107

108

109

110

OFF

C3417M-B (11/06)

Download from Www.Somanuals.com. All Manuals Search And Download.

SWITCH SETTING

SPECTRA

ADDRESS

SPECTRA

ADDRESS

SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

OFF

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

OFF

C3417M-B (11/06)

Download from Www.Somanuals.com. All Manuals Search And Download.

SWITCH SETTING

SPECTRA

ADDRESS

SPECTRA

ADDRESS

SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

OFF

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

OFF

C3417M-B (11/06)

Download from Www.Somanuals.com. All Manuals Search And Download.

Specifications

GENERAL

ELECTRICAL (Dome Drive Only)

Input Voltage

18-32 VAC; 24 VAC nominal

Construction

Back Box

22-27 VDC; 24 VDC nominal

Plastic

Dome Drive

Lower Dome

Cable Entry (Back Box)

Pan Movement

Vertical Tilt

Aluminum, thermoplastic

Acrylic

0.75-inch conduit fitting

360° continuous pan rotation

Unobstructed +2° to -92°

Input Power

24 VAC

23 VA nominal (indoor, without heater)

73 VA nominal (outdoor, with heater)

24 VDC

0.7 A nominal (indoor, without heater)

3 A nominal (outdoor, without heater)

Manual Pan/Tilt Speeds*

Pan

Fuse

1.25 A

0.1°- 80°/sec manual operation,

150°/sec turbo

0.1°- 40°/sec manual operation

Auxiliary Outputs

Alarm Inputs

2 (Spectra IV SE only)

7 (Spectra IV SE only)

Tilt

Relay Contacts

Type

AUX 1

Form C

AUX 2 Output

Open collector

transistor output

Preset Speeds

Pan

Tilt

Environment

In-Ceiling

Environmental In-Ceiling Outdoor

400°/sec

200°/sec

Voltage

Current

Low voltage (<40 V) 32 VDC maximum

2 A maximum

150 mA maximum

Indoor

Environmental In-Ceiling

In-Ceiling

Operating Temperature

7.5 (19.0)

9.9 (25.2)

In-Ceiling Indoor

32° to 122°F (0° to 50°C)

Environmental In-Ceiling (Assumes no wind chill factor)

5.2

4.4

Maximum

140°F (60°C) absolute maximum;

122°F (50°C) sustained maximum

-60°F (-51.1°C) absolute minimum;

prevents icing at sustained

(13.2)

(11.0)

Minimum

3.5

(8.8)

4.3

(10.9)

minimum of -50°F (-45°C); de-ices

0.1 inch (2.5 mm) within 3 hours

after power-up

5.9 (15.0)

8.9 (22.6)

8.2 (20.8)

Weight (approximate)

Back Box

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;

ALL OTHERS ARE INCHES.

In-Ceiling Indoor

1.5 lb (0.68 kg)

Environmental In-Ceiling 2.1 lb (0.95 kg)

Dome Drive

3.3 lb (1.48 kg)

*For variable-speed operation an appropriate controller is

required. With fixed-speed controllers, pan/tilt speed is 20°/sec.

The CM6700/CM6800 controller with the KBD200A keyboard has

programmable fixed speeds.

Lower Dome

In-Ceiling Indoor

0.2 lb (0.09 kg)

Environmental In-Ceiling 0.6 lb (0.27 kg)

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.

This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the

European Union regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures

for recycling this equipment.

C3417M-B (11/06)

Download from Www.Somanuals.com. All Manuals Search And Download.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective

in material or workmanship for a period of one year after the date of

shipment.

warranty repair is required, the Dealer must contact Pelco at

(800)þ289-9100 or (559) 292-1981 to obtain a Repair Authorization number

(RA), and provide the following information:

Exceptions to this warranty are as noted below:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

•

Five years on FR/FT/FS Series fiber optic products and TW3000 Series

unshielded twisted pair transmission products.

•

Three years on Spectra^®IV products.

If there is a dispute regarding the warranty of a product which does not fall

under the warranty conditions stated above, please include a written explana-

tion with the product when returned.

Three years on Genex^®Series products (multiplexers, server, and keyboard).

Three years on Camclosure^®and fixed camera models, except the

CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and

MC3651H-2X camera models, which have a five-year warranty.

Method of return shipment shall be the same or equal to the method by which

the item was received by Pelco.

•

Three years on PMCL200/300/400 Series LCD monitors.

Two years on standard motorized or fixed focal length lenses.

Two years on Legacy^®, CM6700/CM6800/CM9700 Series matrix, and DF5/

DF8 Series fixed dome products.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call

the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization num-

ber (CA number if returned for credit, and RA number if returned for repair).

•

Two years on Spectra III^™, Esprit^®, ExSite^™, and PS20 scanners, including

when used in continuous motion applications.

Two years on Esprit and WW5700 Series window wiper (excluding wiper

blades).

Two years (except lamp and color wheel) on Digital Light Processing (DLP^®)

displays. The lamp and color wheel will be covered for a period of 90 days.

The air filter is not covered under warranty.

All merchandise returned for credit may be subject to a 20% restocking and

refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned

CA or RA number and freight should be prepaid. Ship to the appropriate address

below.

•

Eighteen months on DX Series digital video recorders, NVR300 Series

network video recorders, and Endura^™Series distributed network-based

video products.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico,

send goods to:

•

One year (except video heads) on video cassette recorders (VCRs). Video

heads will be covered for a period of six months.

Six months on all pan and tilts, scanners or preset lenses used in continu-

ous motion applications (that is, preset scan, tour and auto scan modes).

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

Pelco will warrant all replacement parts and repairs for 90 days from the date

of Pelco shipment. All goods requiring warranty repair shall be sent freight

prepaid to Pelco, Clovis, California. Repairs made necessary by reason of mis-

use, alteration, normal wear, or accident are not covered under this warranty.

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico

and are instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco assumes no risk and shall be subject to no liability for damages or loss

resulting from the specific use or application made of the Products. Pelco’s

liability for any claim, whether based on breach of contract, negligence,

infringement of any rights of any party or product liability, relating to the

Products shall not exceed the price paid by the Dealer to Pelco for such

Products. In no event will Pelco be liable for any special, incidental or conse-

quential damages (including loss of use, loss of profit and claims of third

parties) however caused, whether by the negligence of Pelco or otherwise.

Pelco

3500 Pelco Way

Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors

473 Eccles Avenue

South San Francisco, CA 94080 USA

Phone: 650-737-1700

Fax: 650-737-0933

The above warranty provides the Dealer with specific legal rights. The Dealer

may also have additional rights, which are subject to variation from state to

state.

REVISION HISTORY

Manual #

C3417M

C3417M-A

C3417M-B

Date

8/06

9/06

Comments

Original version.

Corrected illustration 7.

11/06

Inserted compatibility table. Added serial port settings to Table E.

Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.

Endura, ExSite, and Spectra III are trademarks of Pelco.

DLP is a registered trademark of Texas Instruments, Inc.

Download from Www.Somanuals.com. All Manuals Search And Download.

Worldwide Headquarters

3500 Pelco Way

Clovis, California 93612 USA

USA & Canada

Tel: 800/289-9100

Fax: 800/289-9150

International

Tel: 1-559/292-1981

Fax: 1-559/348-1120

www.pelco.com

ISO9001

Australia Canada Finland France Italy Russia Singapore Spain Sweden The Netherlands United Arab Emirates United Kingdom United States

Download from Www.Somanuals.com. All Manuals Search And Download.

Peavey Musical Instrument Amplifier MF1 X User Manual
Philips Camera Accessories LR03PS12C 10 User Manual
Philips Indoor Furnishings P 6018 User Manual
Philips Microcassette Recorder DPM 9350 User Manual
Philips Projection Television 9P 5534C User Manual
Pinnacle Design TV Video Accessories TV63003 User Manual
Polar Watch AXN500 User Manual
Polycom IP Phone 500 IP User Manual
Poulan Chainsaw 2004 09 User Manual
Poulan Lawn Mower 185491 User Manual