PLCD3MR
OWNER’S MANUAL
Marine Audio System
• MP3 Player
• PLL Synthesizer Stereo Radio
• Digital Compact Disc Player
• Automatic Memory Storing
• Undetachable Panel
• Preset Equalization
• Electronic Shockproof (ESP) Function
• Auxiliary Input Function
• Remote Control
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Notes:
TAKE OUT SCREWS BEFORE
INSTALLATION
• Choose the mounting location where
the unit will not interfere with the
normal function of the driver.
Before installing the unit, please remove
the two screws.
Take out screws before installation
• Before installing the unit,
connect the wiring temporarily and
make sure it is all connected up
properly and the system works
properly.
• Use only the parts included with the
unit to ensure proper installation.
The use of unauthorized parts can
cause malfunctions.
DIN FRONT-MOUNT (Method A)
Installation Opening
This unit can be installed in any dashboard
having an opening as shown below:
• Consult with your nearest dealer if
installation requires the drilling of holes
or other modifications of the vehicle.
• Install the unit where it does not get in
the driver’s way and cannot injure the
passenger if there is a sudden stop.
53 mm
• If installation angle exceeds 30˚ from
horizontal, the unit might not give its
optimum performance.
182 mm
Installing the unit
Be sure you test all connections first, and
then follow these steps to install the unit.
1. Make sure the ignition is turned off,
and then disconnect the cable from
the vehicle battery's negative (-)
terminal.
2. Disconnect the wire harness and the
antenna.
3. Lift the top of the outer trim ring then
pull it out to remove it.
30˚
• Avoid installing the unit where it would
be subject to high temperature, such
as from direct sunlight, or from hot air,
from the heater, or where it would be
subject to dust, dirt or excessive
vibration.
4. The two supplied keys release tabs
inside the unit's sleeve so you can
remove it. Insert the keys as far as they
will go (with the notches facing up) into
the appropriate slots at the middle left
and right sides of the unit. Then slide
the sleeve off the back of the unit.
DIN FRONT/REAR-MOUNT
This unit can be properly installed either
from “Front” (conventional DIN Front-
mount) or “Rear” (DIN Rear-mount
installation, utilizing threaded screw holes
at the sides of the unit chassis).
For details, refer to the following
illustrated installation methods.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Sleeve
L Key
Note: to install the short threading terminal
of the mounting bolt to the back of the
unit and the other long threading terminal
to the dashboard.
Outer Trim Ring
Front Panel
Spring Washer
Hex Nut
Metal Strap
Mounting Bolt
Plain Washer
R Key
Tapping Screw
5. Mount the sleeve by inserting it into
the opening of the dashboard and bend
open the tabs located around the
sleeve with a screwdriver. Not all tabs
will be able to make contact, so
examine which ones will be most
effective. Bending open the appropriate
tabs behind the dashboard to secure
the sleeve in place.
9. Reconnect the cable to the vehicle
battery's negative (-) terminal. Then
replace the outer trim ring and install
the unit's front panel. (see the steps
of “to install the front panel”).
Dashboard
Tabs
Removing the unit
1. Make sure the ignition is turned off,
then disconnect the cable from the
vehicle battery's negative (-) terminal.
2. Remove the metal strap attached to
the back of the unit (if attached).
3. Lift the top of the outer trim ring then
pull it out to remove it.
Screwdriver
Sleeve
4. Insert both of the supplied keys into
the slots at the middle left and right
sides of the unit, then pull the unit out
of the dashboard.
6. Reconnect the wire harness and the
antenna and be careful not to pinch
any wires or cables.
7. Slide the unit into the sleeve until it
locks into place.
8. To further secure the unit, use the
supplied metal strap to secure the back
of the unit in place. Use the supplied
hardware (Hex Nut (M5mm) and Spring
Washer) to attach one end of the strap
to the mounting bolt on the back of
the unit. If necessary, bend the metal
strap to fit your vehicle's mounting
area. Then use the supplied hardware
(Tapping Screw (5x25mm) and Plain
Washer) to attach the other end of
metal strap to a solid metal part of the
vehicle under the dashboard. This strap
also helps ensure proper electrical
grounding of the unit.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
DIN REAR-MOUNT (Method B)
If your vehicle is a Nissan or Toyota, follow
these mounting instructions.
Use the screw holes marked T (Toyota),
N (Nissan) located on both sides of the
unit to fasten the unit to the factory radio
mounting brackets supplied with your
vehicle.
Side view showing
Screw Holes marked T, N
Factory Radio
Screw
Mounting
Bracket
Screw
Dashboard or
Console
To fasten the unit to the factory radio
mounting brackets.
Align the screw holes on the bracket with
the screw holes on the unit, and then
tighten the screws (5x5mm) on each side.
Note: the outer trim ring, sleeve and the
metal strap are not used for method B
installation.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING CONNECTION
MAIN UNIT
ANTENNA CONNECTOR
FUSE
RED
IGNITION
(GREEN)
(GREY)
SWITCH (ACC+)
SUBWOOFER CABLE
RCA CABLE
FUSE
MEMORY
BACK-UP (B+)
YELLOW
BLACK
GROUND (B–)
Rch RED
Lch WHITE
POWER
BLUE
ANTENNA
WHITE
GREY
FRONT Lch
SPEAKER
FRONT Rch
SPEAKER
WHITE/BLACK
GREY/BLACK
GREEN
VIOLET
REAR Lch
SPEAKER
REAR Rch
SPEAKER
GREEN/BLACK
VIOLET/BLACK
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
LOCATION OF KEYS
1
2
3
4
5
6
7
8
9
25
24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 26
1.
2.
3.
4.
5.
6.
7.
8.
9.
POWER
SEL
DISC SLOT
DISPLAY
EQ
IR REMOTE
EJECT
AUX IN
1>>
14. M5
15. SHF
16. RPT
17. 1 to 6
18. SCN
19. PAU
20. DSP
21. MONO
22. LOC
23. MUTE
24. RESET
25. AS/PS
26. USB interface
10. 1>>
11. BAND ( LOU)
12. MOD
13. M6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
GENERAL OPERATION
EQUALIZATION
Press EQ button (5) to turn on equalization
function and to select desired audio mode.
There are five kinds of modes as shown
below:
• SWITCHING ON/OFF THE UNIT
Switch on the unit by pressing any
button (except EJECT button (7)).
When system is on, press POWER
button (1) to turn off the unit.
FLAT
CLASSICS
POP M
ROCK M
DSP OFF
• SOUND ADJUSTMENT
SUBWOOFER
Press MOD button (12) for several
seconds to toggle sub-woofer output.
Press it for several seconds again to
release this mode.
Press SEL button (2) shortly to select
the desired adjustment mode.
The adjustment mode will change in
the following order:
LIQUID CRYSTAL DISPLAY
Exhibits current frequency and activated
functions on the display (4).
VOL
BAS
TRE
BAL
FAD
(Fader)
(Volume)
(Bass)
(Treble)
(Balance)
By rotating the audio knob (2)
REMOTE SENSOR
clockwise or counter-clockwise, it is
possible to adjust the desired sound
quality.
Point the remote control handset to the
remote sensor IR (6). Press the function
keys on the handset to control the system.
Press and hold the SEL button (2) for
several seconds to adjust beep
options, Rotate the audio knob (2)
clockwise or counter-clockwise to
select as follows:
ESP FUNCTION
If the unit has the electronic shockproof
function, it can be shockproof for several
seconds.
AUXILIARY INPUT
BEEP 2ND
BEEP ALL
BEEP OFF
The unit can be connected to a portable
audio player through the AUX IN jack (8)
on the front panel. After finishing the
connection, you can press MOD button
(12) on the front panel to switch the mode
to AUX IN mode.
- BEEP 2’nd mode:
The beep is only generated when
double key is pressed for (1 sec).
e.g.
When preset button (17) is pressed.
When BND(LOU) button (11) is
pressed. When AS/PS(D-AUD)
button (25) is pressed.
RESET FUNCTION
RESET button (24) must be activated with
either a ballpoint pen or thin metal object.
The RESET button is to be activated for
the following reasons:
- BEEP ALL mode:
The beep is generated when any key
is pressed.
- Initial installation of the unit when all
wiring is completed.
- All the function buttons do not operate.
- Error symbol on the display.
Note: If pressing the RESET button (24)
does not work, please use a cotton swab
soaked in isopropyl alcohol to clean the
socket on the front panel.
- BEEP OFF mode:
The beep is disabled.
LOUDNESS
Press BND/LOU/ENT button (11) for
several seconds to reinforce the bass
output. Press it for several seconds again
to release this function.
MUTE
Press MUT button (23) to mute the sound
instantly. Press any button to get out of
mute mode.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
• LOCAL/DISTANT
RADIO OPERATION
Press LOC button (22) to select
between local and distant stations.
• SWITCHING TO RADIO MODE
Press MOD button (12) momentarily
to select radio mode, the radio mode
appears in the display together with
the memory band and frequency.
Local setting for reception of strong
stations, and a distant setting for
reception of weaker stations. This
function is in effect during AUTO SEEK
operation.
• SELECTING THE FREQUENCY
BAND
MONO/STEREO
In radio mode, press BND/LOU (ENT)
button (11) momentarily to select the
desired band.
Press MON button (21) to select mono
or stereo mode. You can sometimes
improve reception of distant stations
by selection mono operation.
The reception band will change in the
following order:
FM1
FM2
FM3
AM
• SELECTING STATION
Press
button (9) or
button (10)
momentarily to activate automatic
seek function. Press for several
seconds until “MANUAL” appears on
the display, the manual tuning mode
is selected. If both buttons have not
been pressed for several seconds,
they will return to seek tuning mode
and “AUTO” appears on the display.
• AUTOMATIC MEMORY STORING &
PROGRAM SCANNING
- Automatic Memory Storing
Press AS/PS (D-AUD) button (25)
for several seconds, the radio
searches from the current frequency
and checks the signal strength until
one cycle search is finished. Then 6
strongest stations are stored into the
corresponding preset number
button.
- Program Scanning
Press AS/PS (D-AUD) button (25)
momentarily to scan preset stations.
When the field strength level is more
than the threshold level of stop level,
the radio will hold at that preset
number for several seconds with
mute, then search again.
• STATION STORING
Press any one of the preset buttons
(17) (1 to 6) to select a station, which
had been stored in the memory. Hold
the preset button (17) for several
seconds(until it beeps) to assign the
current station to the specific button
pressed.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
CD OPERATION
MP3 OPERATION
• SWITCHING TO CD MODE
If there is no CD inserted in the driver:
Gently insert the CD with the printed
side up into the CD compartment until
you feel some resistance. The CD is
drawn into the driver automatically.
CD playback begins.
• SWITCHING TO CD (MP3) MODE
If there is no MP3 disc inserted in the
driver:
Gently insert the MP3 disc with the
printed side up into the disc slot (3)
until you feel some resistance.
The MP3 disc is drawn into the driver
automatically. The MP3 playback
begins.
If a MP3 disc is already inserted in the
driver:
Keep pressing MOD button (12)
momentarily until the CD (MP3) mode
display appears.
If a CD is already inserted in the driver:
Keep pressing MOD button (12)
momentarily until the CD mode
display appears.
• SELECTING TRACKS
Press
button (10) or
button(9)
to move to the previous track or the
following track. Track number shows
on display.
• EJECTING A DISC
Hold
button (10) or
button (9)
Press button (7) to stop MP3 playing
and eject the disc from the disc slot
(3).
to fast reverse or fast forward. CD play
starts from when you release the
button.
• SELECTING TRACKS IN SINGLE
STEP
• PAUSING PLAYING
Press PAU button (19) to pause CD
player. Press it again to resume play.
Press
button (10) or
button (9)
to move to the previous track or the
following track. Track number shows
on display.
• PREVIEWING ALL TRACKS
Press SCN button (18) to play first
several seconds of each track on the
current disc. Press again to stop intro
and listen to track.
• SELECTING DIRECTORY UP/DOWN
Press M5 button (14) or M6 button (13)
to select directory downward or
upward.
• REPEATING THE SAME TRACK
Press RPT button (16) to continuously
repeat the same track. Press it again
to stop repeat.
If the MP3 disc does not contain any
directory, there is no function for M5
button (14) or M6 button (13).
• PAUSING PLAYING
Press PAU button (19) to pause MP3
player. Press it again to resume play.
• PLAYING ALL TRACKS IN RANDOM
Press SHF button (15) to play all
tracks on CD in random order. Press
again to cancel the function.
• PREVIEWING ALL TRACKS
Press SCN button (18) to play first
several seconds of each track on the
current disc. Press again to stop intro
and listen to track.
• EJECTING A DISC
Press button (7) to stop CD playing
and eject the disc from the disc slot
(3).
• REPEATING THE SAME TRACK
Press RPT button (17) to continuously
repeat the same track. Press it again
to stop repeat.
Note: When you first play a CD and
when a track is playing, press M5
button (14) or M6 button (13), the unit
will search the disc again and start to
play the first track. Later, there is no
function of pressing M5 button (14) or
M6 button (13).
• PLAYING ALL TRACKS IN RANDOM
Press SHF button (15) to play all
tracks on MP3 disc in random order.
Press again to cancel the function.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
• SELECTING TRACKS BY AS/PS/D-
AUD BUTTON
- Use the TUNE/SEEK/TRACK
UP/DOWN buttons to list all
songs under this directory and
select the title.
- Press BND/LOU (ENT) button to
confirm and start the play.
AS/PS (D-AUD) button is assigned as
Digital Audio Mode selection button
in MP3 operation.
When pressed, it selects each mode
of Digital Audio.
“Searching track directly” =>
“Searching Directory or File Name”=>
“Navigation” from root by
TUNE/SEEK/TRACK UP/DOWN
buttons=> “Navigation” from current
directory by TUNE/SEEK/TRACK
UP/DOWN buttons.
- Repeat the above steps if the newly
selected title is again a directory.
Searching From Root Directory
Press AS/PS (D-AUD) button (23) for
three times. The unit searches file or
directory from root by
TUNE/SEEK/TRACK UP/DOWN
buttons. (D-DIR icon turns on if the
name is directory). Display will list all
available directories and songs. Select
the desired directory/songs by using
TUNE/SEEK/TRACK UP/DOWN
buttons and BND/LOU (ENT) button
(24) to confirm. If the selected title is
a song, it starts to play.
If the selected title is a directory name,
display will show (‘ ‘), then
- Use the TUNE/SEEK/TRACK
UP/DOWN buttons to list all songs
under this directory and select the
title.
Searching Track Directly
Press AS/PS (D-AUD) button for one
time. It enters into “Searching track
directly” in Digital Audio CD.
The unit searches the track selected
by following direct numeric buttons:
M1-M6, MOD (7),
TUNE/SEEK/TRACK DOWN (8),
TUNE/SEEK/TRACK UP (9), DSP(0).
If you select three digits, the unit
searches for the track at once. If you
select one or two digits, the unit waits
for ENT (BND/LOU) button to be
pressed. The unit searches for the
track after a few seconds, even if the
enter button is not pressed.
- Press BND/LOU (ENT) button to
confirm and start playing.
- Repeat the above steps if the newly
selected title is again a directory.
Searching Directory or File Name
Press AS/PS (D-AUD) button twice.
It enters into “Searching Directory or
File Name” in Digital Audio CD.
The unit searches files and directories
that have the same character which is
inputted by the user pressing the
corresponding buttons listed on Table
1 below.
Searching From Current Directory
Press AS/PS (D-AUD) button (23) four
times. The unit searches file or
directory from current directory by
TUNE/SEEK/TRACK UP/DOWN
buttons. (D-DIR icon turns on if the
name is directory). The current
directory name is displayed for a
second and the current file name is
displayed (selected). The user can
select the directory or file in the
directory by TUNE/SEEK/TRACK
UP/DOWN buttons. The selected file
can be played by pressing BND/LOU
(ENT) button.
Explain as follows:
- Use the corresponding buttons to
select the characters A to Z, blank,
0 to 9, _, -, +.
- Press SEL button (2) to confirm
entry of each character.
- Press BND/LOU (ENT) button to
start the title search.
In case the selected title is a directory
name, display will show (‘ ‘), then
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
• DISPLAY INFORMATION
MIXED-CD OPERATION (FOR WITH
MIXED-CD OPERATION VERSION
ONLY)
Press DSP button (20) to show
following information, such as the
clock, ID3 TAG (if available: song title,
directory name, artist name and other
contents…) and other information.
If available, the unit can play the mixed-
CD disc (the disc contains both CD audio
tracks and MP3 files).
When you insert a mixed-CD disc into the
CD slot, it starts to play the CD audio
tracks. And the operation is the same with
the CD operation described as above.
If you want to switch to play MP3 files,
press M5 button (14) or M6 button (13),
it will search the disc over again and start
to
KEY Assigned IN Searching mode (Table 1)
AS/PS
BND/LOU
M1
Mode Select
ENTER
A, B, C, 1
D, E, F, 2
G, H, I, 3
J, K, L, 4
play the MP3 files. And the operation is
the same with the MP3 operation
described as above.
M2
If you want to revert to play CD audio
tracks, press M5 button (14) or M6 button
(13) repeatedly, when it jumps to the end
(i.e. when it selects the first directory or
the last directory), and then press M5
button (14) or M6 button (13) again, it will
start to play the CD tracks again.
In this way, you can switch between
playing CD audio tracks or MP3 songs
repeatedly.
M3
M4
M5
M, N, O, 5/
Directory DOWN
M6
P, Q, R, 6/
Directory UP
MOD
S, T, U, 7
USB PLAY OPERATION
On the front panel of unit, there is an USB
interface (26), you can connect an USB
driver through this interface.
When you connect an USB driver through
the interface, the unit will search the
MP3/WMA files and start to play it
automatically. In other mode, you can also
press MOD button (12) to select USB
mode.
When playing the MP3/WMA files in the
device, the operation is the same with the
MP3 operation described above.
Note:
•The main unit can only support the
standard USB-memory disc.
TUNE/SEEK/
TRACK DOWN
V, W, X, 8
TUNE/SEEK/
TRACK UP
Y, Z, SPACE, 9
PUSH SEL
CHARACTER
SHIFT RIGHT
DSP
_, –, +, 0
AUDIO KNOB
CHARACTER SELECT
(A, B - 8, 9, 0)
AUDIO KNOB & TUNE/SEEK/ TRACK
UP/DOWN buttons:
Searching file and directory during
Navigation.
•USB MP3 player is not a standard which
means different brand name or different
models have their own standard. So our
product cannot support all MP3 players.
•When connecting an MP3 player and
there has normal battery in the player
(non rechargeable battery), you should
remove the battery from the MP3 player
then connect it to the USB interface.
Otherwise, it may cause battery burst.
•When in USB play mode, be sure not to
remove the USB driver from the USB
interface.
WMA OPERATION
For units that can play discs, WMA discs
the operation is the same as MP3
operation described above.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SUPPORTED MP3/WMA DECODING
MODES
DISC NOTE
A. Notes on discs:
The main unit supports MP3/WMA (Windows
Media Audio) decoding modes as below.
1.Attempting to use non-standard shape
discs (e.g. square, star, heart) may
damage the unit. Be sure to use round
shape CD discs only for this unit.
2.Do not stick paper or tape etc., onto
the label side or the recording side of
any discs, as it may cause a
malfunction.
Standard
Bit Rate (kbps) Supports
Mode
MPEG1 Audio 32, 48, 64, 96, Stereo
Layer 3
128, 192, 256,
320
64, 96, 128,
192
(44.1kHz)
Windows
Media Audio
(44.1kHz)
Stereo
3.Dirt, dust, scratches and warped discs
will cause misoperation.
The USB solution can support:
1. Folder: 500 max.
2. File: 999 max.
3. Depth of folder: 8 layers
4. Size: 1 GB
B. Notes on CD-Rs (recordable
CDs)/CD-RWs (rewritable CDs):
1.Be sure to use discs with following
marks only for the unit to play:
CAUTION:
When there are important files in the USB
device, do not connect it to the main unit
to play. And don’t play the CD-R/RW disc
that has important files in it. Because any
wrong operation may cause files loss.
And our company assumes no
responsibility for this.
Recordable
Rewritable
2.The unit cannot play a CD-R and
CD-RW that is not finalized.
(Please refer to the manual of your
CD-R/CD-RW recorder or CD-R/
CD-RW software for more information
on finalization process).
3.Depending on the recording status,
conditions of the disc and the
equipment used for the recording,
some CD-Rs/CD-RWs may not be
played on this unit. (See *1)
*1: To have more reliable play back,
please see following
SD/MMC OPERATION
There is a SD/MMC interface (22) on the
front panel of the unit.
When you insert a SD/MMC card in the
SD/MMC interface, the unit will search
the MP3 files or WMA files in the card and
start to play MP3 files or WMA files
automatically. The operation is the same
with the MP3 operation described above.
If in other mode, you can also press
MODE button (11) to select SD/MMC
mode.
recommendations:
a.Use CD-RWs with speed 1x to 4x
and write with speed 1x to 2x.
b.Use CD-Rs with speed 1x to 8x and
write with speed 1x to 2x.
c.Do not play a CD-RW which has
been written for more than 5 times.
When there is no USB driver in the USB
interface, you cannot record to SD/MMC
directly.
When there are important files in the
SD/MMC card, do not connect it to the
main unit to play.
C. Notes on MP3 files (MP3 Version
Only):
1.The disc must be in the ISO9660 level
1 or level 2 format, or Joliet or Romeo
in the expansion format.
2.When naming a MP3 file, be sure the
file name extension is “.MP3”.
3.For a non-MP3 file, even though the
file name extension is “.MP3”, the unit
cannot recognize it.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL HANDSET
1
7
4
3
8
6
9
5
13
12
2
14
10
16
11
15
FUNCTION KEYS & CONTROL
1.
PWR
Power ON/OFF Button
Display Button
2. DSP
3. SEL
Sound Mode Select Button
Volume Up Button
4. VOL
5. VOL
Volume Down Button
6. BND (LOU)
Band Select Button (When pressed momentarily)
Loudness Button (When held down)
Mode Button
7. MODE
8. TUNE/SKIP/CH
9. TUNE/SKIP/CH
10. AS/PS (D-AUD)
11. M1 - M6
12. PAU
Tune/SKIP Down Button
Tune/SKIP Up Button
Automatic Memory Storing & Program Scanning Button
Preset Buttons
Pause Button
13. SCN
Scanning Button
14. RPT
Repeat Button
15. SHF
Shuffle Button
16. Mute
Mute Button
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATION
GENERAL
Power Supply Requirements
Chassis Dimensions
Tone Controls
: DC 12 Volts, Negative Ground
: 178 (W) x 160 (D) x 50 (H)
- Bass (at 100 Hz)
- Treble (at 10 KHz)
Maximum Output Power
Current Drain
:
:
10 dB
10 dB
: 4 x 40 Watts
: 15 Ampere (max.)
CD PLAYER
Signal to Noise Ratio
Channel Separation
Frequency Response
: More than 55 dB
: More than 45 dB
: 40 Hz - 18 KHz
RADIO
FM
Frequency Coverage
IF
Sensitivity (S/N = 30 dB)
Stereo Separation
: 87.5 to 107.9 MHz
: 10.7 MHz
: 4
V
: > 25 dB
AM
Frequency Coverage
IF
Sensitivity (S/N = 20 dB)
: 530 to 1710 KHz
: 450 KHz
: 36 dBu
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
Before going through the checklist, check wiring connection. If any of the problems
persist after check list has been made, consult your nearest service dealer.
Symptom
No power.
Cause
Solution
The car ignition switch is
not on.
If the power supply is
connected to the car accessory
circuits, but the engine is not
moving, switch the ignition key
to “ACC”.
The fuse is blown.
Replace the fuse.
Disc cannot be
loaded or ejected. the player.
Presence of CD disc inside Remove the disc in the player,
then put in a new one.
Inserting the disc upside
down.
Insert the compact disc with
the label facing upward.
Compact disc is extremely Clean the disc or try to play a
dirty or defective disc. new one.
Temperature inside the car Cool off or wait until the
is too high.
temperature returns to normal.
Condensation.
Leave the player off for an hour
or so, then try again.
No sound.
Volume is too low.
Adjust volume to a desired level.
Check wiring connection.
Wiring is not properly
connected.
Sound skips.
The installation angle is
more than 30 degrees.
Adjust the installation angle less
than 30 degrees.
The disc is extremely dirty
or defective disc.
Clean the compact disc, then
try to play a new one.
The operation keys The built-in microcomputer Press the RESET button.
do not work.
is not operating properly
due to noise.
Front panel is not properly fixed
into its place.
The radio does not The antenna cable is not
Insert the antenna cable firmly.
work. The radio
station automatic
selection does not The signals are too weak.
work.
connected.
Select a station manually.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
8800-0C3021-
Download from Www.Somanuals.com. All Manuals Search And Download.
|