Poulan Trimmer PPB300 User Manual

R
Instruction Manual  
Manual de Instrucciones  
Manuel d’Instructions  
PPB300  
For Occasional Use Only  
DANGER:  
Read and follow all Safety Rules and Operating Instructions before  
using this product. Failure to do so can result in serious injury.  
PELIGRO:  
Lea el manual de instrucciones y siga todas las advertencias e  
instrucciones de seguridad. El no hacerlo puede resultar en le-  
siones graves.  
DANGER:  
Lire le manuel d’instructions et bien respecter tous les avertisse-  
ments et toutes les instructions de sécurité. Tout défaut de le  
faire pourrait entraîner des blessures graves.  
Electrolux Home Products, Inc.  
104 Warren Road  
Augusta, GA 30907  
Copyright E2004 Electrolux Home Products, Inc.  
530164256  
3/11/04  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S Always wear heavy, long pants, long sleeves,  
boots, and gloves. Wearing safety leg guards  
is recommended.  
FUEL SAFETY  
S Mix and pour fuel outdoors.  
S Keep away from sparks or flames.  
S Use a container approved for fuel.  
S Do not smoke or allow smoking near fuel or  
the unit or while using the unit.  
S Avoid spilling fuel or oil. Wipe up all fuel  
spills before starting engine.  
S Move at least 10 feet (3 meters) away from  
fueling site before starting engine.  
S Stop engine and allow it to cool before re-  
moving fuel cap.  
S Empty the fuel tank before storing or trans-  
porting the unit. Use up fuel left in the car-  
buretor by starting the engine and letting it  
run until it stops.  
S Store unit and fuel in area where fuel vapors  
cannot reach sparks or open flames from  
water heaters, electric motors or switches,  
furnaces, etc.  
S Always store gasoline in a container ap-  
proved for flammable liquids.  
S Always wear foot protection. Do not go  
barefoot or wear sandals.  
S Secure hair above shoulder length. Secure  
or remove loose clothing and jewelry or cloth-  
ing with loosely hanging ties, straps, tassels,  
etc. They can be caught in moving parts.  
S Being fully covered also helps protect you  
from debris and pieces of toxic plants  
thrown by spinning line/blade.  
S Stay Alert. Do not operate unit when you are  
tired, ill, upset or under influence of alcohol,  
drugs, or medication. Watch what you are do-  
ing; use common sense.  
S Wear hearing protection.  
S Never start or run the engine inside a  
closed room or building. Breathing exhaust  
fumes can kill.  
S Keep handles free of oil and fuel.  
S Always use the handlebar and a properly  
adjusted shoulder strap with a blade (see  
ASSEMBLY).  
CUTTING SAFETY  
UNIT/MAINTENANCESAFETY  
WARNING: Inspect the area to be  
cut before each use. Remove objects (rocks,  
broken glass, nails, wire, string, etc.) which  
can be thrown or become entangled in the  
blade or trimmer head.  
S Keep others including children, animals,  
bystanders, andhelpers at least 50 feet (15  
meters) away. Stop engine immediately if  
you are approached.  
S Always keep engine on the right--handside  
of your body.  
S Hold the unit firmly with both hands.  
S Keep firm footing andbalance. Do not over-  
reach.  
S Keep blade or trimmer head below waist  
level. Do not raise engine above your waist.  
S Keep all parts of your body away from  
blade, trimmer head, and muffler when en-  
gineis running. Ahot mufflercan causese-  
rious burns.  
S Cut from your left to your right. Cutting on  
right side of the shield will throw debris  
away from the operator.  
S Use only in daylight or good artificial light.  
S Use only for jobs explained in this manual.  
WARNING: Stop unit anddisconnect  
the spark plug before performing mainte-  
nance (except carburetor adjustments).  
S Look for and replace damaged or loose  
parts before each use. Look for and repair  
fuel leaks before use. Keep unit in good  
working condition.  
S Throw away blades that are bent, warped,  
cracked, broken, or damaged in any other  
way. Replace trimmer head parts that are  
cracked, chipped, broken, or damaged in  
any other way before using the unit.  
S Maintain unit according to recommended  
procedures. Keep blade sharp. Keep cut-  
ting line at the proper length.  
S Use only 0.080! (2 mm) diameter Poulan  
PRO" brand replacement line. Never use  
wire, rope, string, etc.  
S Install required shield properly before using  
the unit. Use the metal shield for all metal  
blade use. Use the plastic shield for all line  
trimmer use.  
S Use only specified blade or trimmer head;  
make sure it is properly installed and se-  
curely fastened.  
S Never start engine with clutch shroud re-  
moved. The clutch can fly off and cause se-  
rious injury.  
S Besurebladeor trimmerheadstops turning  
when engine idles.  
S Make carburetor adjustments with the low-  
er end supported to prevent blade or trim-  
mer line from contacting any object. Hold  
unit by hand; do not use the shoulder strap  
for support.  
S Keep others away when making carburetor  
adjustments.  
S Use only recommended Poulan PROr ac-  
cessories and replacement parts.  
S Have all maintenance and service not ex-  
plained in this manual performed by your au-  
thorized service dealer.  
TRANSPORTING AND STORAGE  
S Stop the unit before carrying.  
S Keep muffler away from your body.  
S Allow the engine to cool and secure the unit  
before storing or transporting it in a vehicle.  
S Empty the fuel tank before storing or trans-  
porting the unit.Use upfuel leftin thecarbu-  
retor by starting the engine and letting it run  
until it stops.  
S Store unit so the blade or line limiter blade  
cannot accidentally cause injury. The unit  
can be hung by the shaft.  
S Store unit out of reach of children.  
SAFETY NOTICE: Exposure to vibrations  
through prolonged use of gasoline powered  
hand tools could cause blood vessel or nerve  
damage in the fingers, hands, and joints of  
people prone to circulation disorders or abnor-  
mal swellings. Prolonged use in cold weather  
has been linked to blood vessel damage in  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
otherwise healthy people. If symptoms occur  
such as numbness, pain, loss of strength,  
change in skin color or texture, or loss of feeling  
in the fingers, hands, or joints, discontinue the  
use of this tool and seek medical attention. An  
anti--vibration system does not guarantee the  
avoidance of these problems. Users who oper-  
ate power tools on a continual and regular basis  
must monitor closely their physical condition  
and the condition of this tool.  
SPECIAL NOTICE: This unit is equipped  
with a temperature limiting muffler and spark  
arresting screen which meets the require-  
ments of California Codes 4442and 4443. All  
U.S. forest land and the states of California,  
Idaho, Maine, Minnesota, New Jersey, Ore-  
gon, and Washington require by law that  
many internal combustion engines be  
equippedwithaspark arrestingscreen. Ifyou  
operateinalocale wheresuch regulationsex-  
ist, you arelegally responsible formaintaining  
the operatingcondition of theseparts. Failure  
to do so is a violation of the law. For normal  
homeowneruse, themuffler andspark arrest-  
ing screen will not require any service. After  
50 hours of use, we recommend that your  
muffler beserviced orreplacedby your autho-  
rized service dealer.  
ASSEMBLY  
CARTON CONTENTS  
Coupr  
Check carton contents against the following  
LOOSEN  
list:  
S Powerhead  
Shipping  
protector  
S Lower attachment (with trimmer head  
installed)  
S Cupped washer  
S Large nut for installing blades  
S Hex wrench  
S Handlebar  
S Bracket cover  
Knob  
TIGHTEN  
S Bracket cover screws (2)  
S Metal blade shield  
S Blade shield screws (4)  
S 4--point weed blade  
S Plastic shield  
S Wing nut (screwed onto plastic shield)  
S Shoulder strap with warning  
S Container of oil  
2. Remove shipping protector from coupler.  
3. Remove the shaft cap from the brushcutter  
attachment (if present).  
4. Position locking/release button of attach-  
ment into guide recess of coupler.  
5. Push the attachmentintothe coupleruntil  
the locking/release button snaps into the  
primary hole.  
6. Before using the unit, tighten the knob se-  
curely by turning clockwise.  
WARNING: Always stopunit anddis-  
connect spark plug beforeperformingany as-  
sembly procedures.  
Coupler  
Primary Hole  
Guide Recess  
WARNING: If received assembled,  
repeatall steps to ensure your unit is properly  
assembled and all fasteners are secure.  
Locking/  
Release  
Button  
Examine parts for damage. Do not use dam-  
aged parts.  
NOTE: If you need assistance or find parts  
missing or damaged, call 1-800-554-6723.  
Upper  
Shaft  
Lower  
Attachment  
WARNING: Make sure the locking/  
release button is locked in the primary hole  
and the knob is securely tightened before op-  
eratingthe unit. All attachments aredesigned  
to be used in the primary hole.  
For optional attachments, see the AS-  
SEMBLY section of the applicable attach-  
ment instruction manual.  
It is normal for the fuel filter to rattle in the  
empty fuel tank.  
Finding fuel or oil residue on muffler is normal  
due to carburetor adjustments and testing  
done by the manufacturer.  
TOOLS REQUIRED  
S Hex wrench (provided)  
S Adjustable wrench  
S Phillips screwdriver  
ATTACHING THE HANDLEBAR  
DANGER: To avoid serious injury, the  
barrier portion of the handlebar must be installed  
as shown to provide a barrier between operator  
and the spinning blade.  
1. Locate the decal on the handlebar. This  
decal includes an arrow. Position the  
handlebar with the mounting bracket at  
the end of the arrow.  
INSTALLING BRUSHCUTTER  
ATTACHMENT  
CAUTION: When installing brushcutter at-  
tachment, place the unit on a flat surface for  
stability.  
1. Loosen the coupler by turning the knob  
counterclockwise.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Position the bracket cover over the han-  
dlebar. Again make sure the handlebaris  
at the end of the arrow.  
4. Insert two screws into the screw holes.  
5. Secure shoulder strap clamp by tighten-  
ing screws with a hex wrench.  
3. Insert screws and hand tighten only. Be  
sure the handlebar is installed correctly;  
then, tighten each screw securely with  
the hex wrench.  
HARNESS  
ADJUSTMENT  
FOR BALANCE  
Screw  
ar  
6 inches  
4 -- 12 inches  
(15 cm)  
Bracket Cover  
(10 -- 30 cm)  
below  
waist  
above  
ground  
30 inches  
(76 cm)  
Mounting  
Bracket  
ASSEMBLY OF SHOULDER STRAP  
WARNING: Proper shoulder strap  
and handlebar adjustments must be made  
with the engine completely stopped before  
using unit.  
1. Insert your right arm and head through  
the shoulder strap and allow it to rest on  
your left shoulder. Make sure the danger  
sign is on your back and the hookis tothe  
right side of your waist.  
30 inches  
(76 cm)  
NOTE: A one-half twist is built in the shoul-  
der strap to allow the strap to rest flat on the  
shoulder.  
2. Adjust the strap, allowing the hook to be  
about 6 inches (15 cm) below the waist.  
3. Fasten the strap hook to the clamp located  
between the trigger handle and the handle-  
bar clamp base and lift the tool to the oper-  
ating position.  
4. Try on shoulder strap and adjust for fit  
and balance before starting the engine or  
beginning a cutting operation.  
CONFIGURING YOUR UNIT  
You can configure your unit using a cutting head  
for grass and light weeds, or a weed blade for  
cutting grass, weeds, and brush up to 1/2 inch  
(1 cm) in diameter. To assemble your unit, go to  
the section for the desired configuration and fol-  
low the instructions.  
NOTE: It may be necessary to relocate the  
shoulder strap clamp on the shaft for proper  
balancing of unit.  
TO RELOCATE SHOULDER STRAP  
ASSEMBLY INFORMATION --  
TRIMMER HEAD  
CLAMP:  
1. Loosen and remove both clamp screws.  
2. Place the upper shoulder strap clamp  
over the shaft.  
3. Position the lower shoulder strap clamp  
under the shaft and align the upper and  
lower clamp screw holes.  
TRIMMER  
HEAD  
houlder  
amp  
NOTE:Remove the blade and metal shield be-  
fore attaching the plastic shield and trimmer  
head. To remove blade, align hole in the dust  
cup with the hole in theside of the gearbox by  
rotating the blade. Insert a small screwdriver  
into aligned holes. This will keep the shaft from  
turning while loosening the blade nut. Remove  
blade nut by turning clockwise. Remove the  
Lower Shoulder  
Strap Clamp  
Screws  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
screwdriver. Remove both washers and blade.  
To remove metal shield, loosen and remove the  
four mounting screws. See ATTACHING THE  
METAL SHIELD and INSTALLATION OF THE  
METAL BLADE for illustrations. Be sure to store  
all parts and instructions for future use.  
NOTE: The retaining washer must be posi-  
tioned with the raised section facing toward the  
gearbox.  
ASSEMBLY INFORMATION -- WEED  
BLADE  
ATTACHING THE PLASTIC SHIELD  
AND TRIMMER HEAD  
WEED  
BLADE  
WARNING: Theshield must beprop-  
erly installed. The shield provides partial  
protection to the operator and others from the  
risk of thrown objects, and is equipped with a  
line limiter blade which cuts excess line to the  
proper length. The line limiter blade (on un-  
derside of shield) is sharp and can cut you.  
1. Remove wing nut from shield.  
2. Insert bracket into slot on shield.  
3. Pivot shield until boltpasses throughhole  
in bracket.  
NOTE: Remove the trimmer head and plastic  
shield before attaching the metal shield and  
installing the weed blade. To remove the trim-  
mer head, align hole in the dust cup with the hole  
in the side of the gearbox by rotating the dust  
cup. Insert a small screwdriver into aligned  
holes. This will keep the shaft from turningwhile  
loosening the trimmer head. Remove the trim-  
mer head by turning clockwise. Remove the  
screwdriver. To remove the plastic shield, loos-  
en and remove wing nut. Pivot shield to release  
bracket from slot. See INSTALLATION OF  
THECUTTINGHEADandATTACHINGTHE  
PLASTICSHIELDfor illustrations. Be sureto  
store all parts and instructions for future use.  
Never use the trimmer head with the metal  
blade installed.  
4. Tighten the wing nut securely.  
NOTE: If your unit has a plastic cover over  
thethreads on the threadedshaft, removethe  
covering to expose the threads.Beforeinstal-  
ling the trimmer head,make sure the dust cup  
and retaining washer are positioned on the  
gearbox as shown below.  
Bracket  
Slot  
Wing Nut  
ATTACHING THE METAL SHIELD  
Gearbox  
Shield  
WARNING: The metal shield must  
be properly installed on the tool anytime the  
tool is used witha blade.Theforwardtip ofthe  
metal shield helps to reduce the occurrence  
of blade thrust which can cause serious injury  
such as amputation to the operator or by-  
standers. Failure to install the shield in the  
position shown can result in serious injury to  
the operator. The length of the shield must be  
aligned with the length of the shaft.  
Dust Cup  
Retaining Washer  
NOTE: Make sure all parts are properly  
installed as shown in the illustration before  
installing the trimmer head.  
5. Align hole in the dust cup with the hole in  
the side of the gearbox by rotating the  
dust cup.  
1. Place the metal shield under the gearbox,  
and align the screw holes.  
6. Insert a small screwdriver into aligned  
holes. This will keep the shaft from turn-  
ing while tightening trimmer head.  
Gearbox  
Shield  
Screwdriver  
7. While holding thescrewdriver in position,  
thread trimmer head onto the shaft in the  
direction shown on the decal (counter-  
clockwise). Tighten until secure.  
2. Insert and thread the 4 mounting screws  
through the holes of the gearbox and the  
metal shield. Tighten evenly and secure-  
ly with the hex wrench provided.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE: Make sure all parts are in place as il-  
lustrated, and the blade is sandwiched between  
the dust cup and the retaining washer. There  
should be no space between the blade and the  
dust cup or the retaining washer.  
INSTALLATION OF THE METAL  
BLADE  
WARNING: Wear protective gloves  
when handling or performing maintenance on  
the blade to avoid injury. The blade is sharp and  
can cut you even when it is not moving.  
7. Align hole in dust cup with hole in side of  
gearbox by rotating the blade.  
8. Insert a small screwdriver into aligned  
holes. This will keep the shaft from turn-  
ing while tightening the blade nut.  
WARNING: Do not use any blades, or  
fastening hardware other than the washers and  
nuts shown in the following illustrations. These  
parts must be provided by Poulan/Weed Eater  
and installed as shown below. Failure to use  
proper parts can cause the blade to fly off and  
seriously hurt you or others.  
Screwdriver  
NOTE: The dust cup and retaining washer are  
located on the gearbox shaft and not in the parts  
bag. All other fasteners mentioned in the follow-  
ing assembly steps are in the parts bag.  
1. Remove the retaining washer from the  
threadedshaft of the gearbox. Leavethe  
dust cup on the shaft.  
9. TIghten blade nut firmly with a wrench while  
holding screwdriver in position.  
10. Remove the screwdriver.  
2. Install the blade and the retainingwasher  
over the threaded shaft.  
11. Turn blade by hand. If the blade binds  
against the shield, or appears to be uneven,  
the blade is not centered, and you must re-  
install.  
NOTE: To remove blade, insert screwdriver  
into aligned holes. Unthread the nut and re-  
move parts. Be sure to store parts and instruc-  
tions for future use.  
3. Make sure the raised part of the retaining  
washer is facing the gearbox and the  
raised area fits into the hole in the center  
of the blade.  
4. Slide the blade and retaining washer onto  
the shaft of the gearbox.  
5. Place the cupped washer onto the shaft.  
Make sure the cupped side of the washer  
is toward the blade.  
6. Install the blade nut by threading ontothe  
shaft counterclockwise.  
Gearbox  
Shield  
Dust Cup  
Threaded Shaft  
ade  
Retaining  
Washer  
Cupped  
Washer  
Nut  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
K
RT.  
Cols  
a
Handlebar  
Coupler  
Trimmer H
Shaft  
Line Limiter  
Blade  
ON/OFF Switch  
Shield  
Starter Handle  
Primer Bulb  
Throttle Trigger  
Blade  
Choke  
Lever  
Muffler  
ON/OFF SWITCH  
CHOKE  
The ON/OFF switch is located on the trigger  
handle and is used to stop the engine. Move the  
switch to the OFF position to stop the engine.  
The CHOKE helps to supply fuel to the engine  
to aid in cold starting. Activate the choke by  
moving the choke lever to the FULL CHOKE  
position. After the engine attempts to start, move  
the choke lever to the HALF CHOKE position.  
Once engine has started, move the choke lever  
to the OFF CHOKE position.  
PRIMER BULB  
ThePRIMER BULBremoves air from thecar-  
buretor and fuel lines and fills them with fuel.  
This allows you to start the engine with fewer  
pulls on the starter rope. Activate the primer  
bulb by pressing it and allowing it to return to  
its original form.  
COUPLER  
The COUPLER enables optional attach-  
ments to be installed on the unit.  
will cause engine damage. When mixing fuel,  
follow instructions printedoncontainer. Once  
oil is added to gasoline, shake container mo-  
mentarily to assure that the fuel is thoroughly  
mixed. Always read and follow the safety  
rules relating to fuel before fueling your unit.  
BEFORE STARTING ENGINE  
WARNING: Be sure to read the fuel  
information in the safety rules before you be-  
gin. If you do not understandthe safety rules,  
do not attempt to fuel your unit. Call  
1-800-554-6723.  
IMPORTANT  
Experience indicates that alcohol blended  
fuels (called gasohol or using ethanol or  
methanol)can attract moisture which leads to  
separationand formationof acids during stor-  
age. Acidic gas can damage the fuel system  
of an engine while in storage. To avoidengine  
problems, empty the fuel system before stor-  
age for 30 days or longer. Drain the gas tank,  
start the engineand let it rununtil the fuel lines  
and carburetor are empty. Use fresh fuel next  
season. Never use engine or carburetor  
cleanerproductsinthe fuel tank or permanent  
damage may occur.  
FUELING ENGINE  
WARNING: Remove fuel cap slowly  
when refueling.  
HELPFUL TIP  
To obtain the correct oil mix  
ratio, pour 3.2 ounces of  
2--cycle synthetic oil into  
one gallon of fresh gas.  
This engine is certified to operate on un-  
leaded gasoline. Before operation, gasoline  
must be mixed with a good quality synthetic  
2-cycle air-cooled engine oil designed to be  
mixed at a ratio of 40:1. Poulan/Weed Eater  
brand synthetic oil is recommended. Mix gaso-  
line and oil at a ratio of 40:1. A 40:1ratio is ob-  
tainedby mixing 3.2ounces (95ml) ofoil with1  
gallon (4 liters) of unleadedgasoline. DO NOT  
USE automotive oil or marine oil. These oils  
See the STORAGE section for additional in-  
formation.  
HOW TO STOP YOUR UNIT  
S To stop the engine, move the ON/OFF  
switch to the OFF position.  
S If engine does not stop, move choke lever  
to FULL CHOKE position.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Choke  
position  
decal  
Thro
HOW TO START YOUR UNIT  
WARNING: Avoid any contact with  
the muffler. A hot muffler can cause serious  
burns.  
8. Pull starter rope sharply until engine runs,  
but no more than 6 pulls. If the engine  
doesn’t start after 6 pulls (at the HALF  
CHOKE position), move the choke lever to  
the FULL CHOKE position and press the  
primer bulb 6 times. Squeeze and hold the  
throttle trigger and pull the starter rope 2  
more times. Move the choke lever to the  
HALF CHOKE position and pull the starter  
rope until the engine runs, but no more than  
6 pulls. If the engine doesn’t start, repeat  
procedure 2 additional times.  
HELPFUL TIP  
If your engine still does not  
start after following these  
instructions, please call  
1--800--554--6723.  
STARTING A COLD ENGINE (or a  
warm engine after running out of  
fuel)  
NOTE: If engine still doesn’t start, it is  
probably flooded. Proceed to STARTING A  
FLOODED ENGINE.  
9. Oncetheenginestarts, allowit torun 10se-  
conds, then move the choke lever to OFF  
CHOKE by aligning lever with position  
shown on decal (see illustration below). Al-  
low the unit to run for 30 more seconds at  
OFF CHOKE before releasing the throttle  
trigger. NOTE: If engine dies with the  
choke lever in the OFF CHOKE position,  
move the choke lever to the HALF CHOKE  
position and pull the rope until engine runs,  
but no more than 6 pulls.  
Starting Position  
Starter Handle  
Choke  
Lever  
Primer Bulb  
Choke  
position  
decal  
Muffler  
1. Set unit on a flat surface.  
2. Move ON/OFF switch to the ON position.  
3. Slowly press the primer bulb 6 times.  
4. Move choke lever to FULL CHOKE by  
aligning lever with position shown on de-  
cal (see illustration below).  
STARTING A WARM ENGINE  
1. Move ON/OFF switch to the ON position.  
2. Move the choke lever to the HALF  
CHOKE position.  
3. Squeeze and hold the throttle trigger.  
Keep throttle trigger fully squeezed until  
the engine runs smoothly.  
4. Pull starter rope sharply until engine runs,  
but no more than 5 pulls.  
Choke  
position  
decal  
5. Allow engine to run 15 seconds, then  
movethe chokelever tothe OFFCHOKE  
position.  
NOTE: If engine has not started, pull starter  
rope5morepulls. If enginestill doesnot run,it  
is probably flooded.  
5. Squeeze the throttle trigger fully and hold  
through all remaining steps.  
6. Pull starter rope handle sharply until en-  
gine sounds as if it is trying to start, butdo  
not pull rope more than 6 times.  
7. As soon as engine sounds as if it is trying  
to start, move choke lever to HALF  
CHOKE by aligning lever with position  
shown on decal (see illustration below).  
STARTING A FLOODED ENGINE  
Flooded engines can be started by placing  
the choke lever in the OFF CHOKE position;  
then, pull the rope to clear the engine of ex-  
cess fuel. This could requirepulling thestarter  
handle many times depending on how badly  
the unit is flooded.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
If the unit still doesn’t start, refer to  
TROUBLESHOOTING TABLE or call  
1-800-554-6723.  
WARNING: Make sure the locking/  
release button is locked in the primary hole  
and the knob is securely tightened before op-  
erating the unit.  
OPERATING THE COUPLER  
This model is equipped with a coupler which  
enables optional attachments to be installed.  
The optional attachments are:  
OPERATING INSTRUCTIONS  
It is recommended that the engine not be  
operated for longer than 1 minute at full  
throttle.  
OPERATING POSITION  
ALWAYS WEAR:  
MODEL:  
Edger . . . . . . . . . . . . . . . . . . . . . PPB1000E  
Cultivator . . . . . . . . . . . . . . . . . . PPB2000T  
Blower . . . . . . . . . . . . . . . . . . . . PPB3000B  
Pruner . . . . . . . . . . . . . . . . . . . . PP5000P  
Hearing  
Protection  
WARNING: Always stopunit anddis-  
connect spark plug beforeremoving or instal-  
ling attachments.  
Eye Protection  
REMOVING TRIMMER ATTACH-  
MENT (OR OTHER OPTIONAL  
ATTACHMENTS)  
Heavy,  
Long Pants  
CAUTION: When removing or installing at-  
tachments, place the unit on a flat surface for  
stability.  
Boots  
1. Loosen the coupler by turning the knob  
counterclockwise.  
Upper Shaft  
Cut from your left to your right.  
Coupler  
When operating unit, clip shoulder strap onto  
clamp, stand as shown and check for the fol-  
lowing:  
S Wear eye protection and heavy clothing.  
S Extend your left arm and hold handlebar  
grip with your left hand.  
S Hold throttle grip with your right hand with  
finger on throttle trigger.  
LOOSEN  
Lower  
Attachment  
S Keep unit below waist level.  
S Keep shoulder strap pad centered on your  
left shoulder and danger sign centered on  
your back.  
S Maintain full weight of tool on your left  
shoulder.  
TIGHTEN  
Knob  
2. Press and hold the locking/release button.  
Locking/Release  
Button  
S Without bending over, keep the blade or  
trimmer head near and parallel to the  
groundandnot crowdedinto material being  
cut.  
Coupler  
Lower Attachment  
Upper Shaft  
OPERATING INSTRUCTIONS FOR  
USE WITH TRIMMER HEAD  
3. While securely holding the engine and  
upper shaft, pull the attachment straight  
out of the coupler.  
WARNING: Always wear eye protec-  
tion. Never lean over the trimmer head. Rocks  
or debris can ricochet or be thrown into eyes  
and face and cause blindness or other serious  
injury.  
Beforetrimming, bringenginetoa speedsuffi-  
cient to cut material to be trimmed.  
Do not run the engine at a higher speed than  
necessary. The cutting line will cut efficiently  
when the engine is run at less than full throttle.  
At lower speeds, there is less engine noise and  
vibration. The cutting line will last longer and will  
be less likely to “weld” onto the spool.  
INSTALLING OPTIONAL ATTACH-  
MENTS  
1. Remove the shaft cap from the attach-  
ment (if present).  
2. Position locking/release button of attach-  
ment into guide recess of coupler.  
3. Push the attachmentintothe coupleruntil  
the locking/release button snaps into the  
primary hole.  
4. Beforeusing theunit, tightenthe knobse-  
curely by turning clockwise.  
Coupler Primary Hole  
Guide Recess  
Always release the throttle trigger and allow  
the engine to return to idle speed when not  
cutting.  
To stop engine:  
Locking/  
Release  
Button  
S Release the throttle trigger.  
S Move the ON/OFF switch to the OFF posi-  
tion.  
Attachment  
Upper  
Shaft  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TRIMMING -- Hold the bottom of the trimmer  
head about 3 inches (8 cm) above the ground  
and at an angle. Allow only the tip of the line to  
make contact. Do not force trimmer line into  
work area.  
TRIMMER LINE ADVANCE  
Thetrimmerline will advance approximately2  
inches (5 cm) each time the bottom of the  
trimmer headis tappedon the groundwith the  
engine running at full throttle.  
The most efficient line length is the maximum  
length allowed by the line limiter. Always keep  
the shield in place when the tool is being oper-  
ated.  
Trimming  
To advance line:  
S Operate the engine at full throttle.  
S Hold the trimmer headparallel to andabove  
the grassy area.  
S Tap the bottom of the trimmer head lightly on  
the ground one time. Approximately 2 inches  
(5 cm) of line will be advanced with each tap.  
3 inches (8 cm)  
above ground  
Always tap the trimmer head on a grassy area.  
Tapping on surfaces such as concrete or as-  
phalt can cause excessive wear to the trimmer  
head.If the line is worn down to 2 inches (5 cm)  
or less, more than one tap will be required to ob-  
tain the most efficient line length.  
SCALPING -- The scalping technique removes  
unwanted vegetation down to the ground. Hold  
the bottom of the trimmer head about 3 in. (8  
cm) above the ground and at an angle. Allow the  
tip of the line to strike the ground around trees,  
posts, monuments, etc. This technique in-  
creases line wear.  
WARNING: Use only 0.080! (2 mm)  
diameter line. Other sizes of line will not ad-  
vance properly and can cause serious injury.  
Do not use other materials such as wire,  
string, rope, etc. Wire can break off during  
cutting and become a dangerous missile that  
can cause serious injury.  
Scalping  
CUTTING METHODS  
WARNING: Use minimum speed  
anddo not crowdthe line whencuttingaround  
hard objects (rock, gravel, fence posts, etc.),  
whichcandamagethetrimmer head,become  
entangled in the line, or be thrown causing a  
serious hazard.  
S The tip of the line does the cutting. You will  
achieve the best performance and mini-  
mum line wear by not crowding the line into  
the cutting area. The right and wrong ways  
are shown below.  
MOWING -- Your trimmer is ideal for mowing  
in places conventional lawn mowers cannot  
reach. In the mowing position, keep the line  
parallel to the ground. Avoid pressing the  
head into the ground as this can scalp the  
ground and damage the tool.  
Mowing  
Tip of the line  
does the cutting.  
Line crowded into  
work area.  
SWEEPING -- The fanning action of the rotat-  
ingline canbeusedto blow away loosedebris  
from an area. Keep the line parallel to and  
above the area surface and swing the tool  
from side to side.  
Right  
Wrong  
S The line will easily remove grass and  
weedsfromaroundwalls, fences, treesand  
flower beds, but it also can cut the tender  
bark of trees or shrubs and scar fences.  
S For trimming or scalping, use less than full  
throttle to increase line life and decrease  
head wear, especially:  
Sweeping  
S During light duty cutting.  
S Near objects around which the line can  
wrap such as small posts, trees or fence  
wire.  
S For mowing or sweeping, usefull throttlefor  
a good clean job.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S Cut only from your left to your right. Cutting on  
right side of the shield will throw debris away  
from the operator.  
OPERATING INSTRUCTIONS FOR  
USE WITH WEED BLADE  
S Blade Thrust is a reaction that only occurs  
when using a bladed unit. This reaction can  
cause serious injury such as amputation.  
Carefully study this section. It is important that  
you understand what causes blade thrust,  
how you can reduce the chance of its  
occurring, and how you can remain in control  
of unit if blade thrust occurs.  
S WHAT CAUSES BLADE THRUST -- Blade  
Thrust can occur when the spinning blade  
contacts an object that it does not cut. This  
contact causes the blade to stop for an instant  
and then suddenly move or “thrust” away  
from the object that was hit. The “thrusting”  
reaction can be violent enough to cause the  
operator to be propelled in any direction and  
lose control of the unit. The uncontrolled unit  
can cause serious injury if the blade contacts  
the operator or others.  
S WHEN BLADE THRUST OCCURS --  
Blade Thrust can occur without warning if  
the blade snags, stalls, or binds. This is  
more likely to occur in areas where it is  
difficult to see the material being cut. By  
using the unit properly, the occurrence of  
blade thrust will be reduced and the  
operator will be less likely to lose control.  
S Use the shoulder strap and keep a firm grip  
on the unit with both hands. A properly  
adjusted shoulder strap will support the  
weight of the unit, freeing your arms and  
hands to control and guide the cutting motion.  
S Keep feet comfortably spread apart and  
braced for a possible sudden, rapid thrust of  
unit. Do not overreach. Keep firm footing and  
balance.  
S Keep blade below waist level; it will be  
easier to maintain control of unit.  
S Do not raise theengineaboveyour waist as  
the blade can come dangerously close to  
your body.  
S Do not swing unit with such force that you  
are in danger of losing your balance.  
Bring the engine to cutting speed before enter-  
ing the material to be cut.If the blade does not  
turn when you squeeze the throttle trigger, make  
sure shaft is fully inserted into the engine.  
Always release the throttle trigger and allow  
engine to return to idle speed when not cut-  
ting. The blade should not turn while the en-  
gine is runningat idle. If the bladeturns atidle,  
do not use your unit. Refer to theCARBURE-  
TOR ADJUSTMENT section or contact your  
authorized service dealer.  
S Maintain good firm footing while using the  
unit. Do this by planting feet firmly in a  
comfortable apart position.  
S Cut while swinging the upper part of your  
body from left to right.  
S As you move forward to the next area to cut,  
be sure to maintain your balance and footing.  
RECOMMENDED CUTTING POSITION  
2 o’clock  
S Cutonly grass, weeds,andwoody brushup  
to 1/2 inch (1 cm) in diameter with the weed  
blade. Do not let the blade contact material  
it cannot cut such as stumps, rocks,  
fences, metal, etc., or clusters of hard,  
woody brush having a diameter greater  
than 1/2 inch (1 cm).  
Cut using the 2  
o’clock to 4 o’clock  
position of the  
blade  
4 o’clock  
S Keep the blade sharp. A dull blade is more  
likely to snag and thrust.  
S Cut only at full throttle. The blade will have  
maximum cutting powerand is less likely to  
bind or stall.  
S “Feed” the blade deliberately and not too  
rapidly. Theblade can thrustaway if it is fed  
too rapidly.  
WARNING: The operator or others  
mustnottry to clear away cutmaterial withthe  
engine running or the blade turning to avoid  
serious injury. Stop engine and blade before  
removing materials wrappedaround blade or  
shaft.  
ADDITIONAL SAFETY RULES  
FOR OPTIONAL ATTACHMENTS  
WARNING: For each optional at-  
tachment used, read entire instruction manu-  
al before use and follow all warnings and in-  
structions in manual and on attachment.  
WARNING: Ensure handlebar re-  
mains installed on upper shaft (engine end of  
unit) at all times.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
tubes free of debris which can accumulate  
and restrict proper air flow.  
EDGER SAFETY  
S Never place any object in air intake opening  
as this could restrict proper air flow and cause  
damage to the unit.  
S Never use forspreading chemicals, fertilizers,  
or other substances which may contain toxic  
materials.  
S To avoid spreading fire, do not use near leaf or  
brush fires, fireplaces, barbecue pits,  
ashtrays, etc.  
CULTIVATOR SAFETY  
WARNING: Inspect the area to be  
edged before each use. Remove objects  
(rocks, broken glass, nails, wire, etc.) which  
can be thrown by the blade or can wrap  
around the shaft.  
S Blade rotates momentarily after the trigger  
is released. The blade can seriously cut  
you or others.  
S Allow blade to stop before removing it from  
the cut.  
WARNING: Rotating tines can cause  
serious injury. Keep away from rotating tines.  
Stop the engine and disconnect the spark plug  
before unclogging tines or making repairs.  
S Throw away blades that are bent, warped,  
cracked, broken or damaged in any other  
way. Replace parts that are cracked,  
chipped, or damaged before using the unit.  
S Do not attempt to remove cut material nor  
hold material to be cut when the engine is  
running or when cutting blade is moving.  
S Always keep the wheel and depth adjusting  
skid in contact with the ground.  
S Always push the unit slowly over the  
ground. Stay alert for uneven sidewalks,  
holes in the terrain, large roots, etc.  
S Always use the handlebar when using  
edger attachment.  
WARNING: Inspect the area to be  
cultivated beforestarting theunit. Removeall  
debris and hard and sharp objects such as  
rocks, vines, branches, rope, string, etc.  
S Avoid heavy contact with solid objects that  
might stop the tines. If heavy contact occurs,  
stop the engine and inspect the unit for  
damage.  
S Never operate the cultivator without the tine  
cover in place and properly secured.  
S Keep the tines and guard clear of debris.  
S After striking a foreign object, stop the  
engine, disconnect the spark plug and  
inspect the cultivator for damage. Repair  
before restarting.  
S Disconnect attachment from the drive engine  
before cleaning the tines with a hose and  
water to remove any build--up. Oil the tines to  
prevent rust.  
S Always wear gloves when servicing or  
cleaning the tines. The tines become very  
sharp from use.  
BLOWER/VACUUM SAFETY  
WARNING: Inspect area before  
starting unit. Remove all debris and hard ob-  
jects such as rocks, glass, wire, etc. that can  
ricochet, be thrown,or otherwisecause injury  
or damage during operation.  
S Do not set unit on any surface except a clean,  
hard area while engine is running. Debris  
such as gravel, sand, dust, grass, etc., could  
be picked up by the air intake and thrown out  
through discharge opening, damaging unit,  
property, or causing serious injury to  
bystanders or operator.  
S Never place objects inside the blower tubes,  
vacuum tubes or blower outlet. Always direct  
the blowing debris away from people,  
animals, glass, and solid objects such as  
trees, automobiles, walls, etc. The force of air  
can cause rocks, dirt, or sticks tobe thrown or  
to ricochet which can hurt people or animals,  
break glass, or cause other damage.  
S Never run unit without the proper  
equipment attached. When using your unit  
as a blower, always install blower tubes.  
S Check air intake opening, blower tubes or  
vacuum tubes frequently, always with  
engine stopped and spark plug  
disconnected. Keep vents and discharge  
S Do not run unit at high speed unless  
cultivating.  
HEDGE TRIMMER SAFETY  
DANGER: RISK OF CUT; KEEP  
HANDS AWAY FROM BLADE -- Blade moves  
momentarily after the trigger is released. Do not  
attempt to clear away cut material when the  
bladeis in motion. Make surethe switchis inthe  
OFF position, the spark plug wire is discon-  
nected, and the blade has stopped moving be-  
fore removing jammed material from the cutting  
blade. Do not grab or hold the unit by the cutting  
blade.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Blades move  
momentarily  
after the  
Allow blades to stop  
before removing  
them from the cut.  
is  
d.  
WARNING: To prevent serious injury,  
do not use more than one boom extension with  
a pole pruner attachment.  
WARNING: Inspect the area before  
starting the unit. Remove all debris and hard  
objects such as rocks, glass, wire, etc. that  
can ricochet, be thrown, or otherwise cause  
injury or damage during operation.  
WARNING: Keep the pruner away  
from power lines or electrical wires.  
S Only use for pruning limbs or branches up  
to 4 inches (10 cm) in diameter.  
S Do not operate the unit faster than the  
speed needed to prune. Do not run the unit  
at high speed when not pruning.  
S Always stop the unit when work is delayed  
or whenwalking from onecutting locationto  
another.  
S If you strike or become entangled with a  
foreign object, stop the engine immediately  
and check for damage. Have any damage  
repaired by an authorized service dealer  
before attempting further operations.  
Discard blades that are bent, warped,  
cracked or broken.  
S Stop the unit immediately if you feel excessive  
vibration. Vibration is a sign of trouble. Inspect  
thoroughly for loose nuts, bolts or damage  
before continuing. Contact an authorized  
service dealer for repair or replacement of  
affected parts as necessary.  
S Do not use a cutting blade that is bent,  
warped, cracked, broken or damaged in any  
other way. Have worn or damaged parts  
replaced by an authorized service dealer.  
S Always keep unit in front of your body.  
Keep all parts of your body away from the  
cutting blade.  
S Keep the cutting bladeand air vents clear of  
debris.  
POLE PRUNER SAFETY  
WARNING: The reciprocatingblade/  
rotating chain can cause severe injury. In-  
spect the unit before use. Do not operateunit  
with a bent,cracked ordull bladeor dull chain.  
Keep away from the blade/chain.  
WARNING: The reciprocatingblade/  
rotating chain is sharp. Do not touch. To pre-  
vent serious injury, always stop engine and  
ensure blade/chain has stopped moving, dis-  
connect spark plug, and wear gloves when  
changing or handling the blade or chain.  
SNOW THROWER SAFETY  
WARNING: Keep hands and feet  
away from the rotor when starting or running  
the engine. Never attempt to clear the rotor  
with the engine/motor running. Stop engine  
and disconnect spark plug before unclogging  
snow or debris from discharge chute or when  
adjusting vanes.  
WARNING: A coasting blade/rotat-  
ingchaincancauseinjury while it continues to  
move after the engine is stopped. Maintain  
proper control of the unit until the blade/chain  
has completely stopped moving. Keep  
hands, face and feet at a distance from all  
moving parts. Do notattempt to touch or stop  
the blade or chain when it is moving.  
WARNING: Never lean over dis-  
charge chute. Rocks or debris could be  
throwninto the eyes and face and cause seri-  
ous injury or blindness.  
WARNING: Inspect the area where  
the unit is to be used. Remove objects that  
could be thrown or damage the unit. Some  
objects may be hidden by fallen snow -- be  
alert for the possibility.  
WARNING:  
Falling objects can  
cause severe headinjury. Wear headprotec-  
tion when operating this unit with a pole prun-  
er attachment.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
S Direct material discharge away from glass  
enclosures, automobiles, etc.  
S Do not run engine at high speed while not  
removing snow.  
S Be attentive when using the snowthrower,  
and stay alert for holes in the terrain and other  
hidden hazards.  
S Make sure the rotor will spin freely before  
attaching the snowthrower to the powerhead.  
S If the rotor will not rotatefreely due tofrozen  
ice, thaw the unit before thoroughly before  
attempting to operate under power.  
S Keep the rotor clear of debris.  
S Do not throw snow near other people. The  
snow thrower could propel small objects at  
high speed causing injury.  
S After striking a foreign object, stop the  
engine, disconnect spark plug and inspect  
the snowthrower for damage and repair if  
necessary before restarting unit.  
S Never operate the snowthrower near glass  
enclosures, automobiles and trucks.  
S Never attempt to use the snowthrower on a  
roof.  
S Never operate the snowthrower near  
window wells, dropoffs, etc.  
S Never discharge snow onto public roads or  
near moving traffic.  
S Clear snow from slopes by going up and  
down; never across. Use caution when  
changing directions. Never clear snow  
from steep slopes.  
S Let snowthrowerrun for a few minutes after  
clearing snow so moving parts do not  
freeze.  
S Look behind and use care when backing up.  
Exercise caution to avoid slipping or falling,  
especially when operating in reverse.  
S Know how to stop quickly.  
MAINTENANCE  
S Wipe off unit with a clean dry cloth.  
WARNING: Disconnect the spark  
plug before performing maintenance except  
for carburetor adjustments.  
CLEAN AIR FILTER  
A dirty air filter decreases engine perform-  
ance and increases fuel consumption and  
harmful emissions. Always clean after every  
5 hours of operation.  
1. Clean the cover and the area around it to  
keep dirt from falling into the carburetor  
chamber when the cover is removed.  
2. Remove parts by pressing button to re-  
lease air filter cover.  
NOTE: To avoid creating a fire hazard or  
producing harmful evaporative emissions, do  
not clean filter in gasoline or other flammable  
solvent.  
HELPFUL TIP  
IMPORTANT: Have all  
repairs other than the rec-  
ommended maintenance  
described in the instruction  
manual performed by an  
authorized service dealer.  
If any dealer other than an authorized  
service dealer performs work on the  
product, Electrolux Home Products,  
Inc., may not pay for repairs under war-  
ranty. Itis yourresponsibility tomaintain  
and perform general maintenance.  
3. Wash the filter in soap and water.  
4. Allow filter to dry.  
5. Replace parts.  
Air Filter  
Button  
CHECK FOR LOOSE  
FASTENERS AND PARTS  
S Spark Plug Boot  
S Air Filter  
S Housing Screws  
S Assist Handle Screw  
S Debris Shield  
Air Filter  
Cover  
CHECK FOR DAMAGED OR  
WORN PARTS  
Contact an authorized service dealer for re-  
placement of damaged or worn parts.  
S ON/OFF Switch -- Ensure ON/OFF switch  
functions properly by moving the switch to  
the OFF position. Make sure engine stops;  
then restart engine and continue.  
S Fuel Tank -- Discontinue use of unit if fuel  
tank shows signs of damage or leaks.  
S Debris Shield -- Discontinue use of unit if  
debris shield is damaged.  
INSPECTAND CLEANUNIT ANDDE-  
CALS  
S After each use, inspect complete unit for  
loose or damagedparts. Clean theunit and  
decals using a dampcloth with a mild deter-  
gent.  
INSPECT MUFFLER AND SPARK  
ARRESTING SCREEN  
WARNING: The muffler on this prod-  
uct contains chemicals known to the State of  
California to cause cancer.  
As your unit is used, carbon deposits build up  
on the muffler and spark arresting screen and  
must be removed to avoid creating a fire haz-  
ard or affecting engine performance.  
For normal homeowner use, the muffler and  
spark arresting screen will not require any  
service. After 50 hours of use, we recom-  
mend that your muffler be serviced or re-  
placed by an authorized service dealer.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Twist, then pull off spark plug boot.  
2. Remove spark plug from cylinder and  
discard.  
REPLACE SPARK PLUG  
Replace the spark plug each year to ensure  
the engine starts easier and runs better. Set  
spark plug gap at 0.025 inch (0.6 mm). Igni-  
tion timing is fixed and nonadjustable.  
3. Replace with Champion RCJ-6Y spark  
plug and tighten securely with a 3/4 inch  
(19 mm) socket wrench.  
4. Reinstall the spark plug boot.  
SERVICE AND ADJUSTMENTS  
REPLACING THE LINE  
CARBURETOR ADJUSTMENT  
1. Remove spool by firmly pulling on tap  
button.  
WARNING: Keep others away when  
making idle speed adjustments. The trimmer  
head, blade or any optional attachment will be  
spinning during most of this procedure. Wear  
your protective equipment and observe all safe-  
ty precautions. After making adjustments, the  
trimmer head, blade or any optional attachment  
must not move/spin at idle speed.  
The carburetor has been carefully set at the  
factory. Adjustments may benecessary if you  
notice any of the following conditions:  
S Engine will not idle when the throttle is  
released.  
2. Clean entire surface of hub and spool.  
3. Replace with a pre-wound spool, or cut two  
lengths of 12-1/2 feet (3.8 meters) of 0.080!  
(2 mm) diameter Poulan PROr brand line.  
WARNING: Never use wire, rope,  
string, etc., which canbreak offandbecomea  
dangerous missile.  
4. Insert ends of the lines about 1/2 inch (1  
cm) into the small holes on the inside of  
spool.  
Spool  
Small  
Holes  
S The trimmer head, blade or optional  
attachment moves/spins at idle.  
Make adjustments with the unit supported so  
the cutting attachment is off the ground and  
will not make contact with any object. Hold  
the unit by handwhile runningand makingad-  
justments. Keep all parts of your body away  
from the cutting attachment and muffler.  
Line exit holes  
Line in Notch  
Idle Speed Adjustment  
Allow engineto idle. Adjust speed until engine  
runs without trimmer head, blade or optional  
attachment moving or spinning (idle too fast)  
or stalling (idle speed too slow).  
S Turn idle speed screw clockwise to  
increase engine speed if engine stalls or  
dies.  
S Turn idle speed screw counterclockwise to  
decrease engine speed if trimmer head,  
blade or optional attachment moves or  
spins at idle.  
Line in Notch  
Hub  
5. Wind the line evenly and tightly onto the  
spool. Wind in the direction of the arrows  
found on the spool.  
6. Push the lines into the notches, leaving 3  
to 5 inches (7 -- 12 cm) unwound.  
7. Insert the lines into the the exit holes in  
the hub as shown in the illustration.  
8. Align the notches with the line exit holes.  
9. Push spool into hub until it snaps into  
place.  
10. Pull the lines extendingoutsideof thehub  
to release the lines from the notches.  
BLADE REPLACEMENT  
Refer to the ASSEMBLY section for blade re-  
placement instructions and illustrations.  
WARNING: Recheck the idle speed  
after each adjustment. The trimmer head,  
blade or optional attachment must not move  
or spin at idle speed to avoid serious injury to  
the operator or others.  
Air Filter  
Cover  
Idle Speed  
Screw  
If you requirefurtherassistance or areunsure  
about performing this procedure, contact an  
authorized  
service  
dealer  
or  
call  
1--800--554--6723.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STORAGE  
HELPFUL TIP  
WARNING: Perform the following  
During storageof your gas/  
oil mixture, the oil will sepa-  
rate from the gas.  
steps after each use:  
S Allow engine to cool beforestoring or trans-  
porting.  
We recommend that you  
shake the gas can weekly  
to insure proper blending of  
the gas and oil.  
S Store unit and fuel in a well ventilated area  
where fuel vapors cannot reach sparks or  
open flames from water heaters, electric  
motors or switches, furnaces, etc.  
S Store unit with all guards in place. Position  
unit so that any sharp object cannot acci-  
dentally cause injury.  
ENGINE  
S Remove spark plug and pour 1 teaspoonof  
40:1, 2-cycle engine oil (air cooled) through  
the spark plug opening. Slowly pull the  
starter rope 8 to 10 times to distribute oil.  
S Replace spark plug with new one of recom-  
mended type and heat range.  
S Store unit and fuel well out of the reach of  
children.  
SEASONAL STORAGE  
Prepareunit for storage at end of season or if  
it will not be used for 30 days or more.  
If your unit is to be stored for a period of time:  
S Clean the entire unit before lengthy  
storage.  
S Store in a clean dry area.  
S Lightly oil external metal surfaces.  
FUEL SYSTEM  
S Clean air filter.  
S Check entire unit for loose screws, nuts,  
and bolts. Replace any damaged, broken,  
or worn parts.  
S At the beginning of the next season, use  
only fresh fuel having thepropergasolineto  
oil ratio.  
Under FUELING ENGINE in the OPERA-  
TION section of this manual,see messagela-  
beled IMPORTANT regarding the use of ga-  
sohol in your engine.  
OTHER  
S Do not store gasoline from one season to  
another.  
S Replace your gasoline can if it starts torust.  
Fuel stabilizer is an acceptable alternative in  
minimizing the formation of fuel gum deposits  
during storage. Add stabilizer to the gasoline  
in the fuel tank or fuel storage container. Fol-  
low the mix instructions found on stabilizer  
container. Run engine at least 5 minutes after  
adding stabilizer.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING TABLE  
WARNING: Always stop unitand disconnectspark plugbeforeperformingall ofthe  
recommended remedies below except remedies that require operation of the unit.  
TROUBLE  
CAUSE  
REMEDY  
1.ON/OFF switch in  
OFF position.  
2. Engine flooded.  
Engine will not  
start.  
1. Move ON/OFF switch to the ON  
position.  
2. See “Starting a Flooded Engine” in  
Operation Section.  
3. Fuel tank empty.  
4. Spark plug not firing.  
5. Fuel not reaching  
carburetor.  
3. Fill tank with correct fuel mixture.  
4. Install new spark plug.  
5. Check for dirty fuel filter; replace.  
Check for kinked or split fuel line;  
repair or replace.  
6. Carburetor requires  
adjustment.  
6. Contact an authorized service dealer.  
Engine will  
not idle  
properly.  
1. Carburetor requires  
adjustment.  
2. Crankshaft seals worn.  
3. Compression low.  
1. See “Carburetor Adjustment” in  
Service and Adjustments Section.  
2. Contact an authorized service dealer.  
3. Contact an authorized service dealer.  
1. Air filter dirty.  
2. Spark plug fouled.  
1. Clean or replace air filter.  
2. Clean or replace plug  
and regap.  
Engine will not  
accelerate,  
lacks power,  
or dies under  
a load.  
3. Carburetor requires  
adjustment.  
4. Carbon build-up on  
muffler outlet screen.  
5. Compression low.  
3. Contact an authorized service dealer.  
4. Contact an authorized service dealer.  
5. Contact an authorized service dealer.  
Engine  
1. Choke partially on.  
2. Fuel mixture incorrect.  
1. Adjust choke.  
2. Empty fuel tank and refill with  
correct fuel mixture.  
smokes  
excessively.  
3. Air filter dirty.  
4. Carburetor requires  
adjustment.  
3. Clean or replace air filter.  
4. Contact an authorized service dealer.  
1. See “Fueling Engine” in Operation  
section.  
2. Replace with correct spark plug.  
3. Contact an authorized service dealer.  
Engine runs  
hot.  
1. Fuel mixture incorrect.  
2. Spark plug incorrect.  
3. Carburetor requires  
adjustment.  
4. Carbon build-up on  
muffler outlet screen.  
4. Contact an authorized service dealer.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
ELECTROLUX HOME PRODUCTS, INC.,  
THIS WARRANTY GIVES YOU SPECIFIC  
LEGAL RIGHTS, AND YOU MAY HAVE  
OTHER RIGHTS WHICH VARY FROM  
STATE TO STATE.NO CLAIMS FOR CON-  
SEQUENTIALOROTHER DAMAGESWILL  
BE ALLOWED, AND THERE ARE NO  
OTHER EXPRESS WARRANTIES EX-  
CEPT THOSE EXPRESSLY STIPULATED  
HEREIN.  
SOME STATES DO NOT ALLOW LIMITA-  
TIONS ON HOW LONG AN IMPLIED WAR-  
RANTY LASTS OR THE EXCLUSION OR  
LIMITATIONS OF INCIDENTAL OR CON-  
SEQUENTIAL DAMAGES, SO THE ABOVE  
LIMITATIONS OR EXCLUSION MAY NOT  
APPLY TO YOU.  
The policy of ELECTROLUX HOME PROD-  
UCTS, INC., is to continuously improve its  
products. Therefore, ELECTROLUX HOME  
PRODUCTS, INC., reserves the right to  
change, modify, or discontinue models, de-  
signs, specifications, and accessories of all  
products at any time without notice or obliga-  
tion to any purchaser.  
warrants to the original purchaser that each  
new Poulan PRO" brand gasoline tool or at-  
tachment is free from defects in material and  
workmanship and agrees to repair or replace  
under this warranty any defective gasoline  
product or attachment as follows from the  
original date of purchase.  
2 YEARS -- Parts and Labor, when used for  
household purposes.  
90 DAYS -- Parts and Labor, when used for  
commercial, professional, or income produc-  
ing purposes.  
30 DAYS -- Parts and Labor, if used for rental  
purposes.  
This warrantyis not transferableand doesnot  
cover damage or liability caused by improper  
handling, improper maintenance, or the use  
of accessories and/or attachments not spe-  
cifically recommended by ELECTROLUX  
HOME PRODUCTS, INC., for this tool. Addi-  
tionally, this warranty does not cover tune-  
ups, spark plugs, filters, cutting line, or rotat-  
ing head parts that will wear and require  
replacement with reasonable use during the  
warranty period. This warranty does not cov-  
er predelivery setup or normal adjustments  
explained in the instruction manual.  
U.S. EPA / CALIFORNIA / ENVIRONMENT CANADA  
EMISSION CONTROL WARRANTY STATEMENT  
YOUR WARRANTY RIGHTS AND OB-  
LIGATIONS: The U.S. Environmental  
Protection Agency/California Air Resources  
Board,EnvironmentCanadaandELECTRO-  
LUX HOME PRODUCTS, INC., are pleased  
to explain the emissions control system war-  
ranty on your year 2002--2004 small off--road  
engine. In California, all small off--road en-  
gines must be designed, built, and equipped  
to meet the State’s stringent anti--smog stan-  
dards. ELECTROLUX HOME PRODUCTS,  
INC., must warrant the emission control sys-  
tem on your small off--roadenginefor theperi-  
ods of time listed below provided there has  
been no abuse, neglect, or improper mainte-  
nance of your small off--road engine. Your  
emission control system includes parts such  
as the carburetor and the ignition system.  
Where a warrantablecondition exists, ELEC-  
TROLUX HOME PRODUCTS, INC., will re-  
pair your small off--road engine engine at no  
costtoyou. Expenses covered underwarran-  
ty include diagnosis, parts and labor.  
MANUFACTURER’S WARRANTY COV-  
ERAGE:Ifanyemissions relatedpartonyour  
engine (as listed under Emissions Control  
Warranty Parts List) is defective or a defect in  
the materials or workmanship of the engine  
causes the failureof suchan emission related  
part, the part will be repaired or replaced by  
ELECTROLUX HOME PRODUCTS, INC.  
OWNER’S WARRANTY RESPONSIBILI-  
TIES: As the small off--road engine engine  
owner, you are responsible for the perfor-  
mance of the required maintenance listed in  
your instruction manual. ELECTROLUX  
HOME PRODUCTS, INC., recommends that  
you retain all receipts covering maintenance  
on your small off--road engine, but ELEC-  
TROLUX HOME PRODUCTS, INC., cannot  
deny warrantysolely forthe lack of receipts or  
for your failure to ensure the performance of  
all scheduled maintenance. As thesmall off--  
road engine engine owner, you should be  
aware that ELECTROLUX HOME PROD-  
UCTS, INC., may deny you warranty cover-  
age if your small off--road engine engine or a  
part of it has failed due to abuse, neglect, im-  
proper maintenance, unapproved modifica-  
tions, or the use of parts not made or ap-  
proved by  
the original  
equipment  
manufacturer. You are responsible for pres-  
enting your small off--road engine to an  
ELECTROLUX HOME PRODUCTS, INC.,  
authorizedrepaircenteras soonas aproblem  
exists. Warranty repairs should be completed  
in a reasonable amountof time, not to exceed  
30 days. If you have any questions regarding  
your warranty rights and responsibilities, you  
should contact your nearest authorized ser-  
vice center or call ELECTROLUX HOME  
PRODUCTS, INC., at 1--800--554--6723.  
WARRANTY COMMENCEMENT DATE:  
The warranty period begins on the date the  
small off--road engine is purchased.  
LENGTH OF COVERAGE: This warranty  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
shall be for a period of two years from the ini-  
tial date of purchase. WHAT IS COVERED:  
REPAIR OR REPLACEMENT OF PARTS.  
Repair or replacement of any warranted part  
will be performedat no charge to the ownerat  
an approved ELECTROLUX HOME PROD-  
UCTS, INC., servicing center. If you haveany  
questions regarding your warranty rights and  
responsibilities, you should contact your  
nearest authorized service center or call  
ELECTROLUXHOMEPRODUCTS, INC.,at  
1--800--554--6723. WARRANTY PERIOD:  
Any warrantedpartwhich is not scheduledfor  
replacement as required maintenance, or  
which is scheduled only for regularinspection  
to the effect of “repair or replace as neces-  
sary” shall be warrantedfor 2 years. Any war-  
ranted part which is scheduled for replace-  
ment as required maintenance shall be  
warranted for the period of time up to the first  
scheduled replacement point for that part.  
DIAGNOSIS: The owner shall not be  
charged for diagnostic labor which leads to  
the determination that a warrantedpart is de-  
fective if the diagnostic work is performed at  
an approved ELECTROLUX HOME PROD-  
UCTS, INC., servicing center. CONSE-  
QUENTIAL DAMAGES: ELECTROLUX  
HOME PRODUCTS, INC., may be liable for  
damages to other engine components  
caused by the failure of a warranted part still  
under warranty. WHAT IS NOT COVERED:  
All failures caused by abuse, neglect, or im-  
proper maintenance are not covered. ADD  
                                                                                                                                                        
-
ON OR MODIFIED PARTS: The use of add--  
on or modified parts can be grounds for  
disallowing a warranty claim. ELECTROLUX  
HOME PRODUCTS, INC., is not liable to  
cover failures of warranted parts caused by  
the use of add--onor modifiedparts. HOW TO  
FILE A CLAIM: If you have any questions re-  
gardingyour warrantyrights andresponsibili-  
ties, you should contact your nearest autho-  
rized service center or call ELECTROLUX  
HOME  
PRODUCTS,  
INC.,  
at  
1--800--554--6723. WHERE TO GET WAR-  
RANTY SERVICE: Warranty services or re-  
pairs shall be provided at all ELECTROLUX  
HOME PRODUCTS, INC., service centers.  
Call: 1--800--554--6723 MAINTENANCE,  
REPLACEMENT AND REPAIR OF EMIS-  
SION RELATED PARTS: Any ELECTRO-  
LUX HOME PRODUCTS, INC., approvedre-  
placement part used in the performance of  
any warranty maintenance or repair on emis-  
sion related parts will be provided without  
charge to the owner if the part is under war-  
ranty. EMISSION CONTROL WARRANTY  
PARTS LIST: Carburetor, Ignition System:  
Spark Plug (covered up to maintenance  
schedule), Ignition Module, Muffler including  
catalyst. MAINTENANCE STATEMENT:  
Theowner is responsible for the performance  
of all required maintenance as defined in the  
instruction manual.  
The information on the product label indicates which standard your engine is certified.  
Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.  
This engine is certified to be emissions compliant for the following use:  
Moderate (50 hours)  
Intermediate (125 hours)  
Extended (300 hours)  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pentair Swimming Pool Filter PI5 02 User Manual
Pentax Digital Camera OptioWP User Manual
Philips Portable DVD Player PD7030 User Manual
Planet Technology Network Card ISW 800M User Manual
Polaris Offroad Vehicle X2 800 EFI User Manual
Poulan Lawn Mower 163022 User Manual
Poulan Lawn Mower 184564 User Manual
Powermate Portable Generator PMA52530201 User Manual
Pride Mobility Mobility Aid INFMANU3111 User Manual
PS Audio Power Supply Juice Bar User Manual