PLCD67
OWNER’S MANUAL
Mobile Audio System
• PLL Synthesizer Stereo Radio
• Digital Compact Disc Player
• Automatically Memory Storing
• Preset Equalization
• Remote Control
• Electronic Detachable Panel
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Notes:
DIN FRONT-MOUNT (Method A)
Installing the unit
• Choose the mounting location where
the unit will not interfere with the
normal driving function of the driver.
1
2
• Before finally installing the unit,
connect the wiring temporarily and
make sure it is all connected up
properly and the unit and the system
work properly.
53
3
• Use only the parts included with the
unit to ensure proper installation.
The use of unauthorized parts can
cause malfunctions.
(Fig. 1)
1. Dashboard
2. Holder
• Consult with your nearest dealer if
installation requires the drilling of holes
or other modifications of the vehicle.
After inserting the holder into the
dashboard, select the appropriate tab
according to the thickness of the
dashboard material and bend them
inwards to secure the holder in place.
3. Screw
• Install the unit where it does not get in
the driver’s way and cannot injure the
passenger if there is a sudden stop,
like an emergency stop.
1
• If installation angle exceeds 30˚ from
horizontal, the unit might not give its
optimum performance.
6
30˚
2
5
3
7
4
• Avoid installing the unit where it would
be subject to high temperature, such
as from direct sunlight, or from hot air,
from the heater, or where it would be
subject to dust, dirt or excessive
vibration.
(Fig. 2)
1. Dashboard
2. Nut (5mm)
3. Spring washer
4. Screw (5 x 25mm)
5. Screw
DIN FRONT/REAR-MOUNT
This unit can be properly installed either
from “Front” (conventional DIN Front-
mount) or “Rear” (DIN Rear-mount
installation, utilizing threaded screw holes
at the sides of the unit chassis).
For details, refer to the following
illustrated installation methods.
6. Strap
Be sure to use the strap to secure the
back of the unit in place. The strap
can be bent by hand to the desired
angle.
7. Plain washer
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Removing the unit
DIN REAR-MOUNT (Method B)
Installation using the screw holes on the
sides of the unit.
1
1
2
Open/Close
2
4
2
3
3
4
Fastening the unit to the factory radio
mounting bracket.
1. Before removing the frame, press the
OPEN/CLOSE button to slide down
the front panel.
1. Select a position where the screw
holes of the bracket and the screw
holes of the main unit become aligned
(are fitted), and tighten the screws at
2 places on each side.
2. Frame
3. Insert fingers into the groove in the
right side of the frame and pull out to
remove the frame. (You can also
remove the frame from the left side.)
4. Lever
Use either truss screws (5 x 5mm),
depending on the shape of the screw
holes in the bracket.
2. Screw
After removing the frame, press the
OPEN/CLOSE button again to slide
up the front panel. Then insert the
levers supplied with the unit into the
grooves at both sides of the unit as
shown in figure until they click.
Pulling the levers makes it possible to
remove the unit from the dashboard.
3. Factory radio mounting bracket
4. Dashboard or Console
Note: The mounting box, outer trim ring,
and half-sleeve are not used for method
B installation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE DETACHABLE FRONT PANEL
To Detach the Front Panel
To Reinstall the Front Panel
1. Press the OPEN/CLOSE button, the
front panel will slide down.
1. When the panel bracket is in slide
down position, insert the front panel
into panel bracket and press
OPEN/CLOSE button to slide up.
Open/Close
2. Press the OPEN/CLOSE button again,
the front panel will slide up.
Bottom
Button
2. When the panel bracket is in slide up
position, insert a side of the front
panel to its proper position and push
the other side into the panel bracket,
a ‘click’ sound should be heard.
Front Panel
Open/Close
3. When the front panel slides down,
press the bottom button of the front
panel upward and pull it out from the
panel bracket.
3. Note that if the front panel fails to lock
in position properly, press control
button may not function and LCD
display may be missing some
segments. Press the OPEN/CLOSE
button and then reinstall the front
panel again.
Bottom
Button
4. For safekeeping, store the front panel
in the supplied protective case
immediately after being removed.
Protective Case
Front Panel
5
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING CONNECTION
MAIN UNIT
ANTENNA CONNECTOR
(BLACK)
(GREY)
Rch RED
CD IN
IGNITION RED
SWITCH (B+)
Lch WHITE
YELLOW
MEMORY
BACK-UP
CHOKE
BOX
Rch RED
RCA CABLE
BLACK
GROUND (B–)
Lch WHITE
BLUE
POWER
ANTENNA
GREY
WHITE
FRONT Lch
SPEAKER
FRONT Rch
SPEAKER
GREY/BLACK
WHITE/BLACK
GREEN
VIOLET
REAR Lch
SPEAKER
REAR Rch
SPEAKER
GREEN/BLACK
VIOLET/BLACK
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
10
11 24
8
2 23 15
1
7
4
13 16 12 17 19 20 21 14 22
5
18
6
9
3
press it again to slide up the front panel
into the main body or detach the
removable faceplate.
GENERAL OPERATION
• ON/OFF
Switch on the unit by pressing any
button (except OPEN/CLOSE button
(7) and EJECT button (4)).
When system is on, press POWER
button (9) to turn off the unit.
• SOUND ADJUSTMENT
Press SEL button (10) shortly to select
the desired adjustment mode.
The adjustment mode will change in
the following order:
• FACEPLATE RELEASE
Press OPEN/CLOSE button (7) to slide
down the front panel and you can
VOL
(Volume)
BAS
(Bass)
TRE
(Treble)
BAL
(Balance)
FAD
(Fader)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
For Electrical Volume:
• REMOTE SENSOR
By pressing AUDIO CONTROL
button (11) or AUDIO CONTROL
button (12), it is possible to adjust the
desired sound quality.
Point the remote control handset to
the remote sensor RX (23). Press the
function keys on the handset to control
the system.
For Digital Rotating Volume:
By rotating the knob (11 & 12)
clockwise or counter-clockwise, it is
possible to adjust the desired sound
quality.
• RESET
Reset button (24) is placed on the front
panel and must be activated with either
a ball point pen or thin metal object.
The reset button is to be activated for
the following reasons:
• LOUDNESS
Press BND/LOU button (13) to
increase bass output and display will
show “LOUD”. Press it again to
release this function.
- Initial installation of the unit when all
wiring is completed.
- All the function buttons do not
operate.
- Error symbol on the display.
Note: If press RESET button (24), the
unit can’t work yet, please use a cotton
swab soaked in isopropyl alcohol to
clean the socket on the back of the
front panel.
• SET THE CLOCK
Press and hold DSP button (15) until
the clock is shown on the display and
flashed.
Then press the TUNE/SKIP/TRACK
button (17) to change hours or
TUNE/SKIP/TRACK
to change minutes.
button (16)
RADIO OPERATION
• SELECT MODE
Press MOD button (6) to choose
desired listening mode.
• BAND SELECTION
At tuner mode, press BND/LOU button
(13) to select the desired band.
The reception band will change in the
following order:
(e.g. radio mode to CD)
• MUTE
FM1
FM2
FM3
AM
Press MUT button (2) to silence the
receiver. Press it again to release the
mode.
• STATION SELECTION
Press TUNE/SKIP/TRACK
button
button
• LIQUID CRYSTAL DISPLAY
Exhibit current frequency and activated
functions on the display (8).
(16) or TUNE/SKIP/TRACK
(17) shortly to activate automatic seek
function. Press for several seconds
until “MANUAL” appeared on the
display, the manual tuning mode is
selected. If both buttons have not
pressed for several seconds, they will
• EQUALIZATION
Press EQ button (1) to turn on
equalization function and to select
desired audio mode. There are four
kinds of mode as below:
FLAT
CLASSICS
POP M
ROCK M
DSP OFF
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
retune to seek tuning mode and
“AUTO” appeared on the display.
CD OPERATION
• SELECT TRACKS
Press TUNE/SKIP/TRACK
(16) or TUNE/SKIP/TRACK
(17) to move to the previous track or the
following track. Track number shows on
display.
• LOCAL/DISTANCE
button
button
Press LOC button (3) shortly to select between
local and distant stations. Local setting for
reception of strong station, and a distant
setting for reception of weaker stations.
Hold TUNE/SKIP/TRACK
button
button
• AUTOMATICALLY MEMORY
STORING & PROGRAM SCANNING
- Automatic Memory Storing
(16) or TUNE/SKIP/TRACK
(17) to fast reverse or fast forward. CD
play starts from when you release the
button.
Press AMS button (18) for several
seconds, the radio searches from
the current frequency and checks
the signal strength until one cycle
search is finished. And then 6
strongest stations are stored into the
corresponding preset number button.
- Program Scanning
Press AMS button (18) shortly to scan
preset station. When the field strength
level is more than the threshold level of
stop level, the radio is holding at that
preset number for several seconds with
releasing mute, then searches again.
• PAUSE PLAYING
Press PAU button (19) to pause CD
player. Press it again to resume play.
• REPEAT THE SAME TRACK
Press RPT button (21) to continuously
repeat the same track. Press again to
stop repeat.
• PREVIEW ALL TRACKS
Press SCN button (20) to play first
several seconds of each track on the
current disc. Press again to stop intro
and listen to track.
• STATION STORING
Press any one of the preset buttons (14)
(M1 to M6) to select a station which had
been stored in the memory. Press this
button for several seconds, current
station is stored into the number button.
• PLAY ALL TRACKS
DPress SHF button (22) to play all tracks
on CD in random order. Press again to
cancel the function.
• EJECT
When the front panel is sliding down, press
EJECT button (4) to stop CD playing and
eject the disc from the disc slot (5).
NOTE ON CD-R/CD-RW DISCS
• On this unit, in addition to an audio
CD, you can play your original CD-R
or CD-RW that contain audio titles.
•
However, depending on the conditions of
the recording equipment or the CD-R/
CD-RW disc itself, some CD-Rs or
CD-RWs cannot be played on this unit.
• DO NOT stick paper or tape, etc. onto
the label side or the recording side of
any CD-R/CD-RW, as it may cause a
malfunction.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL HANDSET
1
7
4
3
8
6
9
5
2
13
12
10
14
11
15
FUNCTION KEYS & CONTROL
1. PWR
2. DSP
3. SEL
4. VOL
5. VOL
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
Power ON/OFF Button
Display Button
Select Button
Volume Up Button
Volume Down Button
Band Select Button
Mode Button
Tune/Seek Down Button
Tune/Seek Up Button
Automatic Storing & Program Scanning Button
Preset Buttons
Pause Button
Scanning Button
Repeat Button
6. BND
7. MOD
8. TUNE/SEEK
9. TUNE/SEEK
10. AMS
11. M1 - M6
12. PAU
13. SCN
14. RPT
15. SHF
Shuffle Button
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATION
GENERAL
Power Supply Requirements
Chassis Dimensions
Tone Controls
: DC 12 Volts, Negative Ground
: 178 (W) x 180 (D) x 50 (H)
- Bass (at 100 Hz)
- Treble (at 10 KHz)
Maximum Output Power
Current Drain
:
:
10 dB
10 dB
: 4 x 50 Watts
: 5 Ampere (max.)
CD PLAYER
Signal to Noise Ratio
Channel Separation
Frequency Response
: More than 55 dB
: More than 50 dB
: 20 Hz - 20 KHz
RADIO
FM
Frequency Coverage
IF
Sensitivity (S/N = 30 dB)
Stereo Separation
: 87.5 to 107.9 MHz
: 10.71 MHz
: 3 µV
: > 30 dB
AM
Frequency Coverage
IF
Sensitivity (S/N = 20 dB)
: 530 to 1710 KHz
: 10.71 MHz
: 32 dBu
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
Before going through the check list, check wiring connection. If any of the problems
persist after check list has been made, consult your nearest service dealer.
Symptom
Cause
Solution
No power.
The car ignition switch is
not on.
If the power supply is properly
connected to the car accessory
circuits, but the engine is not moving,
switch the ignition key to “ACC”.
The fuse is blown.
Replace the fuse.
Disc cannot
be loaded or
ejected.
Presence of CD disc inside Remove the disc in the player, then
the player.
put a new one.
Inserting the disc in
reverse direction.
Insert the compact disc with the
label facing upward.
Compact disc is extremely Clean the disc or try to play a new
dirty or defective disc. one.
Temperature inside the car Cool off or until the ambient
is too high.
temperature return to normal.
Condensation.
Leave the player off for an hour or
so, then try again.
No sound.
Volume is in minimum.
Adjust volume to a desired level.
Check wiring connection.
Wiring is not properly
connected.
Sound skips.
The installation angle is
more than 30 degrees.
Adjust the installation angle to less
than 30 degrees.
The disc is extremely dirty Clean the compact disc, then try to
or defective disc. play a new one.
The operation The built-in microcomputer Press the RESET button.
keys do not
work.
is not operating properly
due to noise.
Front panel is not properly fixed into
its place.
The radio does The antenna cable is not
not work. The connected.
radio station
Insert the antenna cable firmly.
automatic
The signals are too weak.
Select a station manually.
selection does
not work.
88-C1150-27
Download from Www.Somanuals.com. All Manuals Search And Download.
|