®
GETTING FAMILIAR WITH
YOUR CLIPPER
IMPORTANT SAFEGUARDS
AVAILABLE OSTER LUBRICANTS & CLEANERS,
USING YOUR CLIPPER
& REPLACEMENT PARTS
Regular use of the following products will help you enjoy optimum performance from your
clipper and prolong its functionality.
Commercial Clipper • When using an electrical appliance, basic precautions
should always be followed, including the following:
Read all instructions before using this appliance.
4. Never operate this appliance if it has
Important:
Heavy-Duty Detachable
Blade Clipper
Due to continuous product improvement, product may vary slightly from
what is illustrated.
•
Before using your clipper, apply 1 or 2 drops of Oster® Clipper & Blade
Lube™ Oil to the blade (refer to Taking Care of Your Clipper section).
a damaged cord or plug, if it is not
DANGER
1. Blade guard
working properly, if it has been dropped
To reduce the risk of electric shock:
or damaged, or dropped into water.
1. Do not reach for an appliance that has
Return the appliance to a service center
fallen into water. Unplug immediately.
for examination and repair.
•
•
For best results, hair should be clean and free from styling agents.
During use, apply Kool Lube® coolant occasionally to the blades to keep
2. Blade
3. Blade bracket
4. Blade hinge
Instruction Manual
• For Commercial Use Only •
Model 10 - 76010
them cool.
2. Do not use while bathing or in a
5. Keep cord away from heated surfaces.
shower.
5. Name plate/gear drive assembly access
6. Carbon brush cap/carbon brush
7. Oiler
6. Never operate the appliance when air
3. Do not place or store appliance where
openings are blocked or while on a soft
it can fall or be pulled into a tub or
surface (such as a bed or couch).
sink.
1. Plug unit into an AC electrical outlet.
2. Move On/Off switch to turn clipper on.
8. Power cord
3. Remove blade guard.
9. On/Off switch
7. Never drop or insert any object into
4. Do not place in or drop into water
opening.
4. Insert blade. Holding blade sides, slide blade bracket into hinge.
5. Push blade toward the clipper until it snaps into place
10.Hanging ring
or other liquid.
11.Cleaning Brush
8. Do not use outdoors or operate where
5. Always unplug this appliance from
aerosol spray products are being used
the electrical outlet immediately after
or where oxygen is being administered.
using.
12.Oster® Clipper & Blade Lube™ oil
13.Oster Gear Lube® grease
Oster 5-in-1®
(076300-107)
All-purpose clipper
& blade lubricant
and disinfectant.
Kool Lube®
76300-101
3
Blade Wash®
Cleaning
Solution 76300-
103
Spray
Disinfectant
76300-102
STEP 4
9. Do not use this appliance with a
6. Unplug this appliance before cleaning,
damaged or broken comb or blade,
putting on or taking off parts.
Lubricates and
as cut or scratched skin may occur.
1
cools down blade.
Minimizes bacteria
buildup between
upper and lower
blades.
10. To disconnect, move all controls to
“OFF”, then remove plug from outlet.
11
Flushes away
accumulated hair
and removes dirt
buildup trapped
between upper
and lower cutting
blades.
11.Do not wrap cord around unit when
WARNING
STEP 5
storing. Continuous stress on the
2
To reduce the risk of burns, fire,
3/4
cord can damage cord insulation and
electric shock, or injury to persons:
result in a shock hazard.
6. When finished clipping, turn clipper off and unplug cord from electrical outlet.
7. Cover blade with blade guard to keep it protected.
1. An appliance should never be left
12. Avoid contact with moving blades.
unattended when it is plugged in.
13. Avoid tangling or kinking the cord
2. Close supervision is necessary when
5
while clipping. Should the cord become
this appliance is used by, on, or near
tangled or kinked, stop clipping and
children or invalids.
straighten the cord.
TAKING CARE OF YOUR CLIPPER
3. Use this appliance only for its intended
4
use as described in this manual. Do not
use attachments not recommended by
the manufacturer.
12
Note: Any other maintenance not explained in this manual must be per-
formed by an Oster-Direct® Authorized Service Center.
Important: Make sure clipper is turned off and unplugged from electrical
outlet before removing, replacing or cleaning any parts.
SAVE THESE INSTRUCTIONS
6
Lubricating Motor
THE FOLLOWING PARAGRAPH IS FOR 120-VOLT MARKETS ONLY
To reduce the risk of electrical shock, this appliance has a polarized plug
(one blade is wider than the other). This plug fits a polarized outlet only one
way. This is a safety feature intended to help reduce the risk of electrical
shock. If the plug does not fit fully into the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Do not attempt to defeat this
safety feature.
If you hear a “squeal” or a dry bearing noise
from the motor, it is a signal that the motor
needs lubricating.
Remove cap from Oster® Clipper and Blade
Lube™ tube and insert tip into oiler to apply 1
drop of oil. Be careful not to over lubricate.
Gear Lube®
6
6
8
Blade Lube™
Replacement carbon brushes
(076917-710)
Set of replacement carbon brushes and
springs
Oil 76300-104
Lubricates between
upper and lower
blades to keep
them sharper lon-
ger and produce a
smoother clipping
action
(076300-105)
Specially designed
to prolong the life of
gears, bearings and
the motor.
APPLY 1
DROP
13
Greasing Gear Drive Assembly
ABOUT YOUR CLIPPER
Although your clipper has been thoroughly tested and inspected at every
stage of its manufacturing and assembly, it is recommended that you lubri-
cate it, as instructed in this manual, after 4-6 weeks of extensive use. This
will ensure you obtain optimum performance and prolong the life of your
clipper.
We recommend checking the gear drive
assembly every six months for greasing.
10
9
Caution: Grease only when necessary as over-greasing may cause
leakage and reduce clipper’s efficiency.
Download from Www.Somanuals.com. All Manuals Search And Download.
10-76010_12EM1.indd
1
8/7/12 11:03 AM
|