BDP-LX55
BDP-440
BDP-140
Blu-ray 3DTM PLAYER
For customers in Europe:
Discover the benefits of registering your product online at
Download an electronic version of this manual from our website.
Operating Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
POWER-CORD CAUTION
To prevent a fire hazard, do not place any naked flame
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
sources (such as a lighted candle) on the equipment.
D3-4-2-1-7a_A1_En
For Taiwan exclusively
Taiwanese two pin flat-bladed plug
service center or your dealer for a replacement.
K056_A1_En
S002*_A1_En
Information for users on collection and disposal of old equipment and used batteries
Symbol for
equipment
These symbols on the products, packaging, and/or accompanying documents mean
that used electrical and electronic products and batteries should not be mixed with
general household waste.
For proper treatment, recovery and recycling of old products and used batteries,
please take them to applicable collection points in accordance with your national
legislation.
By disposing of these products and batteries correctly, you will help to save valuable
resources and prevent any potential negative effects on human health and the
environment which could otherwise arise from inappropriate waste handling.
Symbol examples
for batteries
For more information about collection and recycling of old products and batteries,
please contact your local municipality, your waste disposal service or the point of sale
where you purchased the items.
These symbols are only valid in the European Union.
For countries outside the European Union:
If you wish to discard these items, please contact your local authorities or dealer and
ask for the correct method of disposal.
Pb
K058a_A1_En
Cautions on 3D Viewing
sç If you should experience any fatigue or discomfort while viewing 3D images, stop viewing them.
sç Children, particularly those under 6, may be more prone to sensitivity, so guardians should watch for any signs of
fatigue or discomfort.
sç When viewing 3D images, rest periodically.
%XTENDEDçVIEWINGçOFçꢀ$çIMAGESççWITHOUTçRESTçPERIODSçCOULDçCAUSEçFATIGUEçORçDISCOMFORTꢁ
3
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Using the FUNCTION menu . . . . . . . . . . . . . . . . . . . . . . 32
Playing from a specific time (Time Search) . . . . . . . . 32
Playing a specific title, chapter or track (Search) . . . 32
Playing specified range of discs, titles or
01 Before you start
What’s in the box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Putting the batteries in the remote control. . . . . . . . . . 5
Software Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
About operation of this player from a mobile device
(iPod, iPhone, iPad etc.) . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Types of discs/files that can be played. . . . . . . . . . . . . . . 7
Playable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Playable files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . 11
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Front Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
chapter
(track/file) in random order . . . . . . . . . . . . . . . . . . . . . 33
Continuing playback from a specified position
(Continued Viewing Playback) . . . . . . . . . . . . . . . . . . . 33
05 Playback from Home Media Gallery
About Home Media Gallery. . . . . . . . . . . . . . . . . . . . . . . 34
About network playback . . . . . . . . . . . . . . . . . . . . . . . . 34
DLNA Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Disc/USB playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Playing back image files. . . . . . . . . . . . . . . . . . . . . . . . 36
Playing in the desired order (Playlist) . . . . . . . . . . . . . . 36
Adding tracks/files . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Playing the Playlist . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Deleting tracks/files from the Playlist . . . . . . . . . . . . . 37
02 Connecting up
Connecting using an HDMI cable . . . . . . . . . . . . . . . . . 15
About HDMI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
About Control Function with HDMI. . . . . . . . . . . . . . . 16
Connecting a TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Connecting an AV receiver or amplifier . . . . . . . . . . . 18
Connecting video and audio cables. . . . . . . . . . . . . . . . 20
Connecting a TV using a video/audio cable . . . . . . . . 20
Connecting an AV receiver or amplifier using
06 Playing the web contents
Available web contents . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Playing the items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
07 Advanced settings
an optical digital audio cable. . . . . . . . . . . . . . . . . . . . 20
Connecting components to the USB port . . . . . . . . . . . 20
About USB memory devices . . . . . . . . . . . . . . . . . . . . 20
Connecting the USB memory device . . . . . . . . . . . . . 21
Connecting to the network through LAN interface. . . . 21
Connecting to a wireless LAN . . . . . . . . . . . . . . . . . . . 22
Connecting the power cord. . . . . . . . . . . . . . . . . . . . . . . 22
Changing the settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Operating the Initial Setup screen. . . . . . . . . . . . . . . . 39
Software updating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Restoring all the settings to the factory
default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Language Code Table and Country/
Area Code Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
03 Getting Started
08 Additional information
Making settings using the Setup Navigator menu . . . . 23
Operating the TV with the player’s remote control . . . . 24
TV Preset code list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Software license Notice. . . . . . . . . . . . . . . . . . . . . . . . . . 49
Cautions on use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Moving the player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Place of installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Turn the power off when not using the player . . . . . . 54
Condensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Cleaning the player . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Caution for when the unit is installed in a rack
04 Playback
Playing discs or files . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Forward and reverse scanning. . . . . . . . . . . . . . . . . . . 27
Playing specific chapters or tracks . . . . . . . . . . . . . . . 27
Skipping content . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Playing in slow motion . . . . . . . . . . . . . . . . . . . . . . . . . 27
Step forward and step reverse . . . . . . . . . . . . . . . . . . . 27
Playing a specific section within a title or
with a glass door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Cleaning the pickup lens . . . . . . . . . . . . . . . . . . . . . . . 54
Handling discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Control function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Others. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
track repeatedly (A-B Repeat) . . . . . . . . . . . . . . . . . . . 27
Playing repeatedly (Repeat Play) . . . . . . . . . . . . . . . . . 27
Playing in the desired order (Programmed Play) . . . . 28
Making bookmarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Displaying thumbnail images . . . . . . . . . . . . . . . . . . . 28
Switching the camera angles . . . . . . . . . . . . . . . . . . . 28
Switching the subtitles . . . . . . . . . . . . . . . . . . . . . . . . . 29
Displaying the disc information. . . . . . . . . . . . . . . . . . 29
Switching the audio and secondary audio . . . . . . . . . 29
Switching the secondary video . . . . . . . . . . . . . . . . . . 30
Enjoying BONUSVIEW or BD-LIVE . . . . . . . . . . . . . . . 30
Playback functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
4
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
01
Before you start
What’s in the box
WARNING
• Do not use or store batteries in direct sunlight or
other excessively hot place, such as inside a car or
near a heater. This can cause batteries to leak,
overheat, explode or catch fire. It can also reduce the
life or performance of batteries.
• Remote control x 1
• Video/audio cable (yellow/white/red plugs) x 1
• AAA/R03 dry cell batteries x 2
• Warranty card (European and Russian models only)
• Power cord
Caution
• Operating instructions (this document)
• Do not use any batteries other than the ones
specified. Also, do not use a new battery together with
an old one.
Putting the batteries in the
remote control
• When loading the batteries into the remote control,
set them in the proper direction, as indicated by the
polarity marks ( and ).
1
Open the rear cover.
• Do not heat batteries, disassemble them, or throw
them into flames or water.
• Batteries may have different voltages, even if they look
similar. Do not use different kinds of batteries
together.
Press lightly on this
part and slide into
the direction of the
arrow.
• To prevent leakage of battery fluid, remove the
batteries if you do not plan to use the remote control
for a long period of time (1 month or more). If the fluid
should leak, wipe it carefully off the inside of the case,
then insert new batteries. If a battery should leak and
the fluid should get on your skin, flush it off with large
quantities of water.
2
Insert the batteries (AAA/R03 x 2).
Insert as indicated by the / marks into the battery
compartment.
• When disposing of used batteries, please comply with
governmental regulations or environmental public
institution’s rules that apply in your country/area.
Insert the negative
() side first.
3
Close the rear cover.
Close securely (a click should be heard).
The batteries included with the player have been provided
to allow you to check product operation and may not last
long. We recommend using alkaline batteries that have a
longer life.
5
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Software Update
Product information on this player is provided on the
Pioneer website. Check this website for update and
service information on your Blu-ray disc player.
01
IN Europe:
IN U.K.:
IN Russia:
IN Hong Kong:
IN Singapore:
IN Australia
About operation of
this player from a
mobile device (iPod,
iPhone, iPad etc.)
The player can be controlled from a mobile device by
installing the special application onto the mobile device.
For details, see the product information on the Pioneer
website.
This special application may be changed or discontinued
without notice.
6
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Types of discs/files that can be played
01
Playable discs
Discs with the logo marks below indicated on the disc label, package or jacket can be played.
Caution
• Only the discs that have been finalized can be played.
Application format
Disc type
Logo
DATA-
DISC1
CD-DA
DTS-CD
DVD-
DVD-
BDMV
BDAV
DVD VR
Video
Audio
BD-ROM
BD-R
2
BD
BD-RE
3
DVD-ROM
DVD
2,4,5
6
7
DVD-R
4,8
6
7
DVD-RW
2,4
DVD+R
4
DVD+RW
CD-DA
9
(Audio CD)
CD
4
CD-R
4
CD-RW
CD-ROM
1. Discs on which video, image or audio files are recorded. This player does not support multisession discs or multiborder recording.
2. Including dual-layered discs.
3. BDP-LX55 and BDP-440 only.
4. Finalize them before playing them on this player.
5. DVD-R for Authoring discs (3.95 and 4.7 GB) cannot be played.
6. Including the AVCHD format.
7. Including the AVCREC format.
8. Version 1.0 DVD-RW discs cannot be played.
9. Including Video CDs.
7
En
Download from Www.Somanuals.com. All Manuals Search And Download.
• “Blu-ray Disc”, “Blu-ray” and “Blu-ray Disc” logo are
trademarks of Blu-ray Disc Association.
Playing BDs
• BDs (BDMV) compatible with the formats below can
be played.
01
•
is a trademark of DVD Format/Logo Licensing
Corporation.
– Blu-ray Disc Read-Only (ROM) Format Version 2
– Blu-ray Disc Recordable (R) Format Version 2
– Blu-ray Disc Rewritable (RE) Format Version 3
• Corporation and product names mentioned herein are
trademarks or registered trademarks of the respective
corporations.
This player supports BD-ROM Profile 5.
Discs that cannot be played
• HD DVDs
• DVD-RAM discs
It is possible that some discs other than the ones listed
above may not be playable either.
“Blu-ray 3D” and “Blu-ray 3D” logo are trademarks of
Blu-ray Disc Association.
Note
BONUSVIEW functions such as playback of
secondary video (Picture-in-Picture) and secondary
audio can be used. The data used with the
BONUSVIEW functions (the secondary video
(Picture-in-Picture) and secondary audio data) may
be stored in the storage. For details on secondary
video and secondary audio playback, refer to the
disc’s instructions.
• Some discs cannot be played, even if one of the logo
marks on the previous page is indicated.
• To play 8 cm discs, set the disc in the 8 cm disc
depression in the center of the disc tray. No adapter
is necessary. 8 cm BD-ROMs cannot be played.
About audio formats
The following audio formats are supported on this player:
• Dolby TrueHD
“BONUSVIEW” is trademark of Blu-ray Disc
Association.
• Dolby Digital Plus
• Dolby Digital
BD-LIVE functions such as downloading movie
trailers or additional audio and subtitle languages
and playing on-line games can be enjoyed over the
Internet. The data downloaded with the BD-LIVE
function (trailers, etc.) is stored in the storage. Refer
to the disc’s instructions for details about BD-LIVE
functions.
• DTS-HD Master Audio
• DTS-HD High Resolution Audio
• DTS Digital Surround
• MPEG audio (AAC)
• Linear PCM
To enjoy the surround sound of Dolby TrueHD, Dolby
Digital Plus, DTS-HD Master Audio and DTS-HD High
Resolution Audio, it is recommended to connect the
player to an AV receiver or amplifier compatible with
these audio formats using an HDMI cable. After loading
a BD containing sound in one of these audio formats,
select the audio format on the menu screen.
“BD-LIVE” logo is trademark of Blu-ray Disc
Association.
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
Manufactured under license under U.S. Patent Nos:
5,956,674; 5,974,380; 6,226,616; 6,487,535; 7,392,195;
7,272,567; 7,333,929; 7,212,872 & other U.S. and worldwide
patents issued & pending. DTS-HD, the Symbol, & DTS-HD
and the Symbol together are registered trademarks & DTS-
HD Master Audio | Essential is a trademark of DTS, Inc.
Product includes software. © DTS, Inc. All Rights Reserved.
8
En
Download from Www.Somanuals.com. All Manuals Search And Download.
With BD-ROMs, it is possible to use BD-J (Java)
applications to create highly interactive titles, for
example including games.
About region numbers
Blu-ray Disc Player and BD-ROM or DVD-Video discs are
assigned region numbers according to the region in
which they are sold.
01
This player’s region numbers are:
• BD-ROM:
– Europe, Australia and New Zealand models: B
– Russia models: C
– Others: A
• DVD-Video:
– Europe models: 2
– Australia and New Zealand models: 4
– Russia models: 5
Oracle and Java are registered trademarks of Oracle
and/or its affiliates. Other names may be trademarks of
their respective owners.
– Others: 3
• BDs (BDAV) compatible with the formats below can
be played.
Discs not including these numbers cannot be played.
Discs playable on this player are as shown below.
– Blu-ray Disc Recordable (R) Format Version 1
– Blu-ray Disc Rewritable (RE) Format Version 2
• BDs:
– Europe, Australia and New Zealand models: B
(including B) and ALL
Playing DVDs
– Russia models: C (including C) and ALL
– Others: A (including A) and ALL
• DVDs:
– U.K. models: 2 (including 2) and ALL
This label indicates playback compatibility with DVD-RW
discs recorded in VR format (Video Recording format).
However, for discs recorded with a record-only-once
encrypted program, playback can only be achieved using a
CPRM compatible device.
– Australia and New Zealand models: 4 (including 4)
and ALL
– Russia models: 5 (including 5) and ALL
– Others: 3 (including 3) and ALL
The AVCHD is a high definition (HD) digital video camera
recorder format recording high-definition onto certain
media by using highly efficient codec technologies.
Playing CDs
Regarding copy protected CDs: This player is designed to
conform to the specifications of the Audio CD format.
This player does not support the playback or function of
discs that do not conform to these specifications.
“AVCHD” and the “AVCHD” logo are trademarks of
Panasonic Corporation and Sony Corporation.
DualDisc playback
A DualDisc is a two-sided disc, one side of which
contains DVD content — video, audio, etc. — while the
other side contains non-DVD content such as digital
audio material.
The DVD side of a DualDisc can be played on this player.
The non-DVD, audio side of the disc is not compatible
with this player.
It is possible that when loading or ejecting a DualDisc,
the opposite side to that being played will be scratched.
Scratched discs may not be playable.
For more detailed information on the DualDisc
specification, please refer to the disc manufacturer or
disc retailer.
9
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing discs created on computers Supported video file formats
01
• DivX Plus HD
or BD/DVD recorders
®
®
DivX Certified to play DivX and DivX PlusTM HD
(H.264/MKV) video up to 1080p HD including
premium content.
• It may not be possible to play discs recorded using a
computer due to the application settings or
computer’s environment settings. Record discs in a
format playable on this player. For details, contact the
dealer.
®
ABOUT DIVX VIDEO: DivX is a digital video format
®
created by DivX, Inc. This is an official DivX Certified
device that plays DivX video. Visit divx.com for more
information and software tools to convert your files
into DivX video.
• It may not be possible to play discs recorded using a
computer or a BD/DVD recorder, if burn quality is not
good due to characteristics of the disc, scratches, dirt
on the disc, dirt on the recorder’s lens, etc.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX
About video, audio, and image files
and folders
Audio and image files can be played on this player when
the folders on the disc or USB memory device are created
as described below.
®
Certified device must be registered in order to play
purchased DivX Video-on-Demand (VOD) movies. To
obtain your registration code, locate the DivX VOD
section in your device setup menu. Go to
vod.divx.com for more information on how to
complete your registration.
Example of folder structure:
Root
*
001.jpg/001.mp3
xxx.jpg/xxx.mp3
®
®
DivX , DivX Certified , DivX PlusTM HD and associated
logos are trademarks of DivX, Inc. and are used under
license.
*
001.jpg/001.mp3
xxx.jpg/xxx.mp3
01 Folder
Folder
001.jpg/001.mp3
Note
xxx.jpg/xxx.mp3
001.jpg/001.mp3
*
*
®
• This DivX Certified device must be registered in
XX Folder
order to play DivX Video-on-Demand (VOD) content.
First generate the DivX VOD registration code for your
device and submit it during the registration process.
Important: DivX VOD content is protected by a DivX
DRM (Digital Rights Management) system that
restricts playback to registered DivX Certified devices.
If you try to play DivX VOD content not authorized for
your device, the message Authorization Error will be
displayed and your content will not be played. Learn
xxx.jpg/xxx.mp3
* The number of folders and files within a single folder
(including the root directory) is limited to a maximum of
256. Also, keep the number of folder layers to a maximum
of 5.
Note
– This player’s DivX VOD registration code can be
checked at HOME MENU Initial Setup
Playback DivX(R) VOD DRM Registration
Code (page 42).
• The file and folder names displayed on this player may
differ from those displayed on a computer.
Playable files
Video, image and audio files recorded on DVDs and CDs
can be played.
– The number of views is restricted for some DivX
VOD files. When such files are played on this
player, the remaining number of views is displayed.
Files for which the remaining number of views has
reached 0 cannot be played (This DivX rental has
expired is displayed). Files for which the number of
views is not restricted can be played as many times
as you like (the remaining number of views is not
displayed).
Caution
• In DVD, only the one recorded by the ISO 9660 file
system can be played.
• Some files may not be playable.
• For some files, it may not be possible to use certain
functions during playback.
• It may not be possible to play some files, even if they
have the extension of a file playable on this player.
• Files protected by DRM (Digital Rights Management)
cannot be played (not including DivX VOD files).
10
En
Download from Www.Somanuals.com. All Manuals Search And Download.
• MKV
MKV files can be played.
Part Names and
Functions
01
– MKV is a file format allowing multiple audio and
video files to be held in a single file.
– The files that can be played are as follows:
Resolution: Up to 1 280 x 720
Extension: “.mkv” or “.MKV”
Remote Control
19
20
• Windows Media™ Video (WMV)
1
2
Windows Media™ Video (WMV) files can be played.
– The files that can be played are as follows:
Resolution: Up to 1 280 x 720
Extension: “wmv” or “WMV”
21
3
– Files encoded using the Windows Media™ Encoder
9 series are supported.
– Windows Media is either a registered trademark or
trademark of Microsoft Corporation in the United
States and/or other countries.
22
23
4
5
24
25
– This product includes technology owned by
Microsoft Corporation and cannot be used or
distributed without a license from Microsoft
Licensing, Inc.
6
7
8
26
Supported image file formats
• JPEG
9
• Progressive JPEG
File format: JFIF Ver. 1.02/Exif Ver. 2.2
10
27
Resolution: Up to 4 096 x 4 096 pixels
28
29
Supported audio file formats
• Windows Media™ Audio 9 (WMA9)
Bit rate: Up to 192 kbps
11
12
13
14
30
31
32
Sampling frequencies: 22.05 kHz, 32 kHz, 44.1 kHz
and 48 kHz
15
33
• MPEG-1 Audio Layer 3 (MP3)
Bit rate: Up to 320 kbps
Sampling frequencies: 8 kHz, 11.025 kHz, 12 kHz,
16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz and 48 kHz
34
35
36
16
37
38
17
18
• Free Lossless Audio Codec (FLAC) (Only for BDP-
LX55)
Sampling frequencies: 96 kHz to 192 kHz
Quantization bitrate: 16 bit, 24 bit
Channel: 2ch
Playable file extensions
• Video files
1
2
STANDBY/ON – Press to turn the power on and
off.
.divx, .mkv, .wmv and .avi
CONTINUED – Use to continue playback from a
specified position. (page 33)
• Image files
.jpg and .jpeg
3
4
TV CONTROL – (page 24)
• Audio files
.wma and .mp3
.flac (BDP-LX55 only)
AUDIO – (page 29)
11
En
Download from Www.Somanuals.com. All Manuals Search And Download.
5
FL DIMMER
24 HDMI
BDP-LX55 – Use to switch HDMI Mode alternately
01
BDP-LX55, BDP-440 – Each time this is pressed, the
brightness of the front panel display changes and/or
the lighting status of the indicators on the front panel
switches as shown in the table below.
(pages 16 and 41).
BDP-440/BDP-140 – Use to switch the resolution of
the video signals output from the HDMI OUT terminal
(page 41).
Indicators
Front panel
display
Blu-ray
PQLS
FL OFF
25 EXIT – (page 38)
(BDP-LX55 only)
26 POP UP MENU/MENU – Press to display the
Bright
Middle
Dark
Off
Lights
Lights
Lights
Off
Lights
Lights
Lights
Off
Off
BD-ROM or DVD-Video menus.
Off
27
RETURN – Press to return to the previous
screen.
Off
Lights
28 Color buttons – Use these to navigate BD-ROM
BDP-140 – Each time this is pressed, the brightness
of the front panel display switches (in 4 levels).
menus.
PROGRAM – (page 28)
CD/SACD
BOOK MARK – (page 28)
ZOOM – (page 28)
For hybrid discs, press to switch between the CD and
SACD layers.
INDEX – (page 28)
6
TOP MENU – Press to display the top menu of the BD-
ROM or DVD-Video.
29 FWD – (page 27)
7
8
9
FUNCTION – (page 32)
30
// – (page 27)
HOME MEDIA GALLERY – (page 34)
31 STOP – (page 26)
32 2nd VIDEO – (page 30)
33 2nd AUDIO – (page 29)
34 A-B – (page 27)
/// – Use to select items, change settings
and move the cursor.
ENTER – Press to execute the selected item or enter a
setting that has been changed, etc.
10
HOME MENU – (page 39)
35 ENTER – Press to execute the selected item or enter a
setting that has been changed, etc.
11 REV – (page 27)
12 PLAY – (page 26)
13 // – (page 27)
14 PAUSE – (page 26)
36 REPEAT – (page 27)
37 SKIP SEARCH – Press to skip 30 seconds ahead when
SKIP SEARCH is pressed during playback.
38 REPLAY – Press to jump back 10 seconds when
15 Number buttons – Use these to select and play the
title/chapter/track you want to view or listen to and to
select items from menus.
REPLAY is pressed during playback.
Keylock function
You can set the keylock to prevent accidental operations.
16 CLEAR – Press to clear the numeric number, etc.
17 DISPLAY – (page 29)
This function allows TVs compatible with control function
with HDMI to also perform a Key Lock on the player.
18 KEYLOCK – (page 12)
Press and hold KEYLOCK for more than 2 seconds.
• Each time you perform this operation, the function is
activated or deactivated.
19 Remote control LED – Lights when a command is
sent from the remote control. Flashes while the TV
band code is being set.
• If you try to operate the player while the keylock
function is set, LOCK lights on the front panel display.
20 OPEN/CLOSE – Press to open and close the disc
tray.
Note
21 RECEIVER CONTROL
22 SUBTITLE – (page 29)
23 ANGLE – (page 28)
• This remote control unit is equipped with two ENTER
buttons (9 and 35 listed above).
• To operate an AV receiver equipped with a remote
control mode setting using the RECEIVER CONTROL
buttons, set the AV receiver’s remote control mode to
“1”. For details, see the AV receiver’s operating
instructions.
12
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Front Panel
01
BDP-LX55
1
2
3
4
5
6
7
8
9
10
11
BDP-440
1
2
3
4
6
7
8
9
10
11
BDP-140
1
3
4
6
8
9
10
11
1
2
STANDBY/ON – Press to turn the power on and
off.
7
8
9
PQLS indicator (BDP-LX55 and BDP-440 only) –
(page 17)
FL OFF indicator (BDP-LX55 and BDP-440 only) –
(page 12)
OPEN/CLOSE – Press to open and close the disc
tray.
3
4
5
6
Disc tray
– Press to stop playback.
Front panel display
10 USB port – (page 20)
Blu-ray indicator (BDP-LX55 only) – (page 12)
11 – Press to start playback.
Remote control sensor – Point the remote control to
this, then operate it within approximately 7 m.
The player may have trouble capturing remote control
signals if there is a fluorescent light nearby. If this
happens, move the player away from the fluorescent
light.
13
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear Panel
01
BDP-LX55
1
2
3
4
5
6
7
8
BDP-440
1
2
3
4
5
6
8
BDP-140
3
4
2
1
5
6
8
1
2
3
4
HDMI OUT terminal(s) – (below and page 15)
VIDEO OUTPUT terminals – (page 20)
5
6
7
LAN (10/100) terminal – (page 21)
USB port – (page 20)
DIGITAL OUT (OPTICAL) terminal – (page 20)
AUDIO OUTPUT terminals – (page 20)
RS-232C terminal (BDP-LX55 only) – This terminal is
not used.
8
AC IN – (page 22)
About the HDMI terminals on the BDP-LX55
MAIN – Connect with an HDMI-compatible TV or/and AV receiver or amplifier. This is the terminal that is used mainly.
SUB – Connect with an HDMI compatible AV receiver or amplifier. This terminal is only for outputting audio signals.
Note
• No video signal can be output through the SUB terminal. Make sure to connect your TV to the MAIN terminal.
14
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
02
Connecting up
Be sure to turn off the power and unplug the power cord
from the power outlet whenever making or changing
connections.
This product is compatible with “x.v.Color” that have the
capability to realize a wide-gamut color space based on
the xvYCC specifications.
Playing video signals conforming to “xvYCC” standards
on this player when this player is connected to an
“x.v.Color”-compatible TV, etc., expands color
reproduction capabilities, allowing natural colors to be
reproduced more faithfully than ever.
“x.v.Color” is a promotion name given to the products that
have the capability to realize a wide-gamut color space
based on the international standard specifications
defined as xvYCC.
After connecting, make the settings at the Setup
Navigator or Initial Setup menu according to the type of
cable connected (page 23).
Also refer to the operating instructions for the device
being connected.
Note
• The illustrations used here are mainly of the BDP-
LX55.
Connecting using an
HDMI cable
The audio and video signals can be transferred to HDMI-
compatible devices as digital signals with no loss of
sound or video quality.
“x.v.Color” and
Corporation.
are trademarks of Sony
Playable audio signals through the
HDMI OUT terminal
• Dolby TrueHD
Note
• For the BDP-LX55, make the HDMI Mode setting at
the Initial Setup menu according to the connection
of the devices to the player (pages 16 and 41).
• Dolby Digital Plus
• Dolby Digital
• DTS-HD Master Audio
• DTS-HD High Resolution Audio
• DTS Digital Surround
• MPEG-2 AAC
• Make the settings at the Setup Navigator menu
according to the connected HDMI-compatible device
(page 23).
• 1080p video signals may not be output, depending on
the HDMI cable being used.
• Linear PCM
Linear PCM audio signals meeting the following
conditions can be output:
About HDMI
This player incorporates the High-Definition Multimedia
Interface (HDMI®) technology.
– Sampling frequency: 32 kHz to 192 kHz
– Number of channels: Up to 8 (up to 6 for a 192 kHz
sampling frequency)
When connected to a DVI device
• It is not possible to connect DVI devices
(computer displays, for example) that are not
compatible with HDCP. HDCP is a specification to
protect audiovisual content across the DVI/HDMI
interface.
HDMI, the HDMI Logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing, LLC in the United States and other countries.
• No audio signals are output. Connect using an audio
cable, etc.
The player supports Deep Color.
• This player is designed for connection with HDMI-
compatible devices. When connected to a DVI device,
it may not operate properly depending on the DVI
device.
The conventional players can transmit a video signal with
8 bit color depth in the YCbCr 4:4:4 or RGB format; the
players supporting Deep Color can transmit a video
signal with a color bit depth of greater than 8 bits per
color component. Subtle color gradations can be
reproduced when this player is connected to a TV that
supports Deep Color.
15
En
Download from Www.Somanuals.com. All Manuals Search And Download.
• The power of the Flat Screen TV and the player
turns on and off automatically. (Simultaneous
power function)
About Control Function with
HDMI
The functions work when a control function with HDMI-
compatible Pioneer Flat Screen TV or AV system (AV
receiver or amplifier, etc.) is connected to the player using
an HDMI cable.
02
When playback on the player is started or the HOME
MENU is displayed, if the Flat Screen TV’s power was
off, its power turns on automatically. When the Flat
Screen TV’s power is turned off, the player’s power
automatically turns off.
Also refer to the operating instructions for the Flat Screen
TV and AV system (AV receiver or amplifier, etc.).
Setting the HDMI Mode (Only for
BDP-LX55)
To use the control function with
The BDP-LX55 has two HDMI OUT (MAIN, SUB)
terminals. See page 14 for the details on these terminals.
HDMI
• The control function with HDMI operates when
control function with HDMI is set to On for all devices
connected with HDMI cables.
The HDMI Mode needs to be selected before playback to
use the control function appropriately.
To make the setting, press HOME MENU to display the
Home Menu, select Initial Setup Audio Output
HDMI Mode.
• Once the connections and the settings of all the
devices are finished, be sure to check that the player’s
picture is output to the Flat Screen TV. (Also check
after changing the connected devices and
See the table below and set up the HDMI Mode
reconnecting HDMI cables.) The control function with
HDMI may not operate properly if the player’s picture
is not properly output to the Flat Screen TV.
• Use High Speed HDMI® Cables when using the
control function with HDMI. The control function with
HDMI may not operate properly if other HDMI cables
are used.
according to your connection style.
HDMI OUT MAIN
HDMI OUT SUB
HDMI
Mode
Video Audio Control Video Audio Control
Single
Separate
Pure
Audio
• For some models, the control function with HDMI
may be referred to as “KURO LINK” or “HDMI
Control”.
Caution
• The control function with HDMI does not work with
devices of other brands, even if this player is
connected with an HDMI cable.
• No video signal is output through the SUB terminal.
This terminal is only for audio signals.
Sound Retriever Link
About Sound Retriever Link
What the control function with
HDMI can do
• Outputting the optimum picture quality to a Flat
Screen TV compatible with the control function
with HDMI.
Sound Retriever Link is a sound quality correction control
technology that automatically adjusts the compressed
sound quality for the connected AV receiver using HDMI
control function.
Sound Retriever Link function allows you to enjoy higher
quality audio by setting the connected AV receiver’s
Sound Retriever function automatically.
When the control function with HDMI is enabled,
video signals with the optimum picture quality for
control function with HDMI are output from the
player’s HDMI terminal.
Sound Retriever Link function on this player works
exclusively with the following situations.
• Operating the player with the Flat Screen TV’s
remote control.
• PC Audio Stream that is played by USB devices or via
network.
Such player operations as starting and stopping
playback and displaying the menus can be performed
from the Flat Screen TV.
• The Pioneer AV receiver compatible with Sound
Retriever Link function is connected to this player
through an HDMI cable and the player’s setting is set
as shown below (page 41).
• The player’s playback picture is displayed on the
Flat Screen TV’s screen. (Auto-select function)
Control: On
The input switches automatically on the Flat Screen
TV and AV system (AV receiver or amplifier, etc.) when
playback is started on the player or the HOME MENU
is displayed. When the input is switched, the playback
picture, the HOME MENU appears on the Flat Screen
TV.
• Also refer to the instructions of the AV receiver.
• See Pioneer website about AV receivers compatible
with Sound Retriever Link function.
16
En
Download from Www.Somanuals.com. All Manuals Search And Download.
About the PQLS function (Only for
BDP-LX55 and BDP-440)
Caution
02
• Connect the player directly to the Pioneer AV receiver
compatible with Sound Retriever Link function.
Interrupting a direct connection with an amplifier or
AV converter (such as an HDMI switch) can cause
malfunction.
PQLS (Precision Quartz Lock System) is a digital audio
transfer control technology using the HDMI control
function. The player’s output signals are controlled from
the AV receiver to achieve high sound quality playback
using the receiver’s quartz oscillator. This eliminates the
influence of the jitter generated during signal transfer
which can adversely affect the sound quality.
Stream Smoother (only for the BDP-
LX55)
Stream Smoother is a function that automatically
improves picture quality when playing network video
contents by using a built-in high picture quality circuit to
reduce mosquito noise, block noise, etc.
• This player supports the functions below.
– The “PQLS 2ch Audio” function that is only
activated when playing music CDs (CD-DAs)
– The “PQLS Multi Surround” function that is
activated when playing all discs (BDs, DVDs, etc.)
with linear PCM audio output
Note
– The “PQLS Bitstream” function that is activated
when playing with bitstream audio output
• On the BDP-LX55, this function is activated even
when no AV receiver is connected.
• The various PQLS functions are activated when a
Pioneer AV receiver supporting the PQLS functions is
connected directly to the HDMI OUT terminal with an
HDMI cable and the player’s settings are set as
shown below (page 41).
Stream Smoother Link (Only for
BDP-440 and BDP-140)
About Stream Smoother Link
Control: On
Stream Smoother Link is a function that improves picture
quality of network video contents using the control
function with HDMI. Stream Smoother Link function
allows you to enjoy a high quality picture with less noise
by setting the connected AV receiver’s Stream Smoother
function automatically.
• Also refer to the AV receiver’s operating instructions.
• See the Pioneer website for AV receivers supporting
the PQLS function.
Caution
Stream Smoother Link function on this player works
exclusively with the following situations.
• The PQLS function may stop working when the video
output resolution is switched. The PQLS function will
start working again once playback is stopped then
restarted.
• Playback of PC contents stored on discs and USB
devices.
• The Pioneer AV receiver with Stream Smoother Link
function is connected to this player through an HDMI
cable.and the player’s setting is set as shown below
(page 41).
• When the PQLS 2ch function is activated, the output
from the player’s VIDEO OUTPUT jacks may not have
the proper colors. If this happens, connect the TV and
AV receiver’s HDMI terminals to view the picture.
Control: On
• Turn on the power of the AV receiver connected to the
HDMI OUT terminal, then start playback of the disc.
• Also refer to the instructions for the AV receiver.
• See Pioneer website about AV receivers compatible
with Stream Smoother Link function.
Note
• PQLS indicator on the player’s front panel display
lights when the PQLS function is activated (page 13).
Caution
• Connect the player directly to the Pioneer AV receiver
compatible with Stream smoother Link function.
Interrupting a direct connection with an amplifier or
AV converter (such as HDMI switch) can cause
malfunction.
17
En
Download from Www.Somanuals.com. All Manuals Search And Download.
BDP-440/BDP-140
Connecting a TV
See Connecting an AV receiver or amplifier on the right
column to connect an AV receiver or amplifier using an
HDMI cable.
02
BDP-440’s rear panel
Caution
• Hold the plug when connecting and disconnecting
the cable.
• Placing a load on the plug could result in faulty
contact and no video signals being output.
Match the direction of
the plug to the terminal
and insert straight.
BDP-LX55
Connect a TV to the HDMI OUT (MAIN) terminal.
To HDMI
input terminal
It is also possible to connect to an
AV receiver or amplifier using an
HDMI cable (below).
BDP-LX55’s rear panel
Direction of signal flow
TV
Connecting an AV receiver or
amplifier
Connect to an AV receiver or amplifier in order to enjoy
the surround sound of Dolby TrueHD, Dolby Digital Plus,
Dolby Digital, DTS-HD Master Audio, DTS-HD High
Resolution Audio or DTS Digital Surround. For
instructions on connecting the TV and speakers to the AV
receiver or amplifier, refer to the operating instructions
for AV receiver or amplifier.
Match the direction of
the plug to the terminal
and insert straight.
To HDMI
input terminal
It is also possible to connect to an
AV receiver or amplifier using an
HDMI cable (on the right column).
Direction of signal flow
TV
Caution
• Hold the plug when connecting and disconnecting
the cable.
It is also possible to connect a TV via AV reciever or
amplifier to HDMI OUT (MAIN) terminal. See Connecting
an AV receiver or amplifier on the right column.
• Placing a load on the plug could result in faulty
contact and no video signals being output.
Caution
• Make sure to connect a TV to HDMI OUT (MAIN)
terminal, video signals cannot be output from HDMI
OUT (SUB) terminal.
• Make sure to set HDMI Mode to Single (page 41).
18
En
Download from Www.Somanuals.com. All Manuals Search And Download.
BDP-LX55
Caution
02
BDP-LX55’s rear panel
• Make sure to connect a TV to HDMI OUT (MAIN)
terminal, video signals cannot be output from HDMI
OUT (SUB) terminal.
• Make sure to set HDMI Mode to Separate (page 41).
• If the AV amplifier connected to the HDMI OUT (SUB)
terminal is also connected to a TV, the TV’s input may
switch automatically. If this happens, turn off the
control function with HDMI on the TV.
HDMI cable
(commercially available)
BDP-440/BDP-140
AV receiver
or amplifier
BDP-440’s rear panel
Match the
directionofthe
plug to the
terminal and
insert straight.
AV receiver
or amplifier
From HDMI output
terminal to HDMI input
terminal
HDMI cable
(commercially
available)
Match the direction
of the plug to the
terminal and insert
To HDMI
input terminal
straight.
Direction of signal flow
AV receiver
or amplifier
TV
Achieving better video and sound quality
From HDMI
To HDMI input
terminal
When connecting one TV (or projector) and AV amplifier
to the player, connect in such a way that the video and
audio signals are transferred separately in order to
achieve higher quality video and sound.
output
TV
terminal
Direction of signal flow
BDP-LX55’s rear panel
HDMI cable
(commercially available)
AV receiver
or amplifier
Match the
directionofthe
plug to the
terminal and
insert straight.
Direction of signal flow
TV
19
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting an AV receiver or
amplifier using an optical
digital audio cable
Connecting video and
audio cables
02
Note
BDP-LX55’s rear panel
• Make the settings in the Setup Navigator menu
according to the type of cable connected (page 23).
• To output video signals from this player, connect
using a video cable (not including when connected
using an HDMI cable).
Red
White
Connecting a TV using a
video/audio cable
Video/audio cable
(included)
Optical digital audio
cable (commercially
available)
2-channel analog
audio can also be
connected.
Caution
• Connect the player’s video output directly to
your TV.
To optical digital
audio input terminal
To audio input terminals
AV receiver or
amplifier
This player supports the analog copy protection
technology. Therefore, the picture may not be
displayed properly if this player is connected to a TV
via a DVD recorder/video deck or when playing the
player’s output material that is recorded by a DVD
recorder/video deck. Furthermore, the picture may
not be displayed properly due to the copy protection
when the player is connected to a TV with a built-in
video deck. For details, contact the manufacturer of
your TV.
Direction of signal flow
Note
• To switch the video from the AV receiver or amplifier,
also connect the video output terminals.
Connectingcomponents
to the USB port
The data downloaded with the BD-LIVE function and the
data used with the BONUSVIEW function when playing
BD-ROMs can be stored on a device connected to the
USB port (USB memory).
BDP-LX55’s rear panel
Yellow
Red
White
About USB memory devices
The USB memory devices that can be connected to the
player are as shown below.
It is also possible to connect to
an AV receiver or amplifier.
Connect the audio signals using
an optical digital audio cable or
an audio cable (2 channels) (on
the right column).
• USB 2.0-compatible memory devices
• FAT16 or FAT32 file system, minimum 1 GB capacity
(2 GB or more recommended)
Direction of
signal flow
To video/audio input terminals
Note
• Devices formatted with a file system other than the
above cannot be used. Such devices may however be
usable if they are formatted from the player.
TV
• USB memory devices may not be recognized if they
contain multiple partitions.
Note
• Some USB memory devices may not operate with this
player.
• Video signals are output with a resolution of 480/576I
or 480/576P when this player is connected using a
video cable.
• Operation of USB memory devices is not guaranteed.
• Depending on the output video resolution setting, the
picture may not be output.
20
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the USB memory
device
Connecting to the
network through LAN
interface
By connecting this player to the network via the LAN
terminal, you can play audio files stored on the
components on the network, including your computer,
using HOME MEDIA GALLERY inputs.
02
Caution
• Be sure to turn the player’s power off before
connecting or disconnecting USB memory devices.
• Use empty USB memory devices (on which nothing is
stored).
• If the USB memory device is write-protected, be sure
to disable the write-protection.
BDP-LX55’s rear panel
• Placing excessive loads on the plug may result in
poor contact, making it impossible to write data on
the USB memory device.
Internet
• When a USB memory device is connected and the
player’s power is turned on, do not unplug the power
cord.
• USB external hard disks cannot be connected to the
player.
LAN cable
(commercially
available)
Modem
Player’s front panel
Router
LAN
3
2
1
WAN
PC
USB memory device
LAN cable
(commercially available)
BDP-LX55’s rear panel
Connect the LAN terminal on this receiver to the LAN
terminal on your router (with or without the built-in DHCP
server function) with a straight LAN cable (CAT 5 or
higher).
Turn on the DHCP server function of your router. In case
your router does not have the built-in DHCP server
function, it is necessary to set up the network manually.
For details, see Setting the IP address on page 44 .
USB memory device
LAN terminal specifications
LAN terminal: Ethernet jack (10BASE-T/100BASE-TX)
Note
Note
• Devices may not work if connected to the USB port via
a memory card reader or USB hub.
• Refer to the operation manual of the equipment you
have as the connected equipment and connection
method may differ depending on your Internet
environment.
• When using a broadband Internet connection, a
contract with an Internet service provider is required.
For more details, contact your nearest Internet
service provider.
21
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to a wireless LAN
Wireless connection to the network is possible through a
wireless LAN connection. Use the separately sold
AS-WL300 for connection.
Connecting the power
cord
02
Connect the power cord after all the connections between
devices have been completed.
• Refer to the operating instructions of AS-WL300 for
the setting details.
BDP-LX55’s rear panel
BDP-LX55’s rear panel
Internet
Power cord (included)
To wall outlet
Modem
LAN/USB feeder cable
(included with the AS-WL300)
Router
WAN
Wireless LAN converter
(AS-WL300)
DC 5V Ethernet
WPS
22
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
03
Getting Started
3
Start Setup Navigator.
Making settings using
the Setup Navigator
menu
Press ENTER.
• Setup Navigator starts.
4
Select the OSD language.
Use / to select, then press ENTER.
Be sure to perform these settings when using the player
in the following situations.
When a Pioneer Flat Screen TV that is compatible with
Control function is connected to this player’s HDMI OUT
terminal, language settings are imported from the
Pioneer Flat Screen TV’s language settings before Setup
Navigator begins.
• When you use the player for the first time.
• After Initial Setup format.
• After updating the player’s software.
5
Select the appropriate output resolution for the
connected TV.
Use / to select, then press ENTER.
Caution
• Before turning on the power, check that the
connections between the player and other devices are
correct. Also, turn on the power of the devices
connected to the player before turning on the player’s
power.
6
TV.
Select the appropriate aspect for the connected
Use / to select, then press ENTER.
7
Close the Setup Navigator menu.
Press ENTER.
• When using a Pioneer Flat Screen TV or front
projector compatible with the Control function, set
Control to On on the connected device before turning
on the player’s power.
• Setup Navigator finishes and the setting is stored.
• Press
screen.
RETURN to go back to the previous
Note
• When a Pioneer Flat Screen TV or front projector
compatible with the Control function is connected to
the player using an HDMI cable, the player is
automatically set to the optimum picture quality for
the connected device.
1
Turn on the TV’s power and switch the input.
See the TV’s operating instructions for the details of
operating the TV.
2
Turn on the player’s power.
Press STANDBY/ON.
Check that the Setup Navigator menu is displayed.
If the Setup Navigator menu is not
displayed
Press
HOME MENU to display the Home
Menu, select Initial Setup Setup Navigator
Start, then press ENTER.
23
En
Download from Www.Somanuals.com. All Manuals Search And Download.
TV Preset code list
Manufacturer Code(s)
Operating the TV with
the player’s remote
control
03
PIONEER 00, 31, 32, 07, 36, 42, 51, GPM 41
22
GRAETZ 31, 42
ACURA 44
ADMIRAL 31
AIWA 60
GRANADA 07, 35, 42, 43, 48
GRADIENTE 30, 57
GRANDIN 18
When the manufacturer code for your brand of TV is set
on the player’s remote control, the TV can be operated
using the player’s remote control.
AKAI 32, 35, 42
AKURA 41
ALBA 07, 39, 41, 44
AMSTRAD 42, 44, 47
ANITECH 44
GRUNDIG 31, 53
HANSEATIC 07, 42
HCM 18, 44
HINARI 07, 41, 44
HISAWA 18
Caution
• For some models it may not be possible to operate the
TV with the player’s remote control, even for TVs of
brands listed on the manufacturer code list.
ASA 45
ASUKA 41
AUDIOGONIC 07, 36
BASIC LINE 41, 44
BAUR 31, 07, 42
BEKO 38
HITACHI 31, 33, 34, 36, 42, 43, 54,
06, 10, 24, 25, 18
HUANYU 56
HYPSON 07, 18, 46
ICE 46, 47
• The setting may be restored to the default after the
batteries are replaced. If this happens, reset it.
IMPERIAL 38, 42
INDIANA 07
BEON 07
BLAUPUNKT 31
BLUE SKY 41
BLUE STAR 18
BPL 18
INGELEN 31
INTERFUNK 31, 32, 07, 42
INTERVISION 46, 49
ISUKAI 41
BRANDT 36
ITC 42
BTC 41
ITT 31, 32, 42
JEC 05
JVC 13, 23
KAISUI 18, 41, 44
KAPSCH 31
BUSH 07, 41, 42, 44, 47, 56
CASCADE 44
CATHAY 07
CENTURION 07
CGB 42
CIMLINE 44
KENDO 42
KENNEDY 32, 42
CLARIVOX 07
CLATRONIC 38
CONDOR 38
CONTEC 44
CROSLEY 32
KORPEL 07
KOYODA 44
LEYCO 07, 40, 46, 48
LIESENK&TTER 07
LOEWE 07
CROWN 38, 44
CRYSTAL 42
CYBERTRON 41
DAEWOO 07, 44, 56
DAINICHI 41
DANSAI 07
DAYTON 44
DECCA 07, 48
DIXI 07, 44
LUXOR 32, 42, 43
M-ELECTRONIC31, 44, 45, 54, 56,
07, 36, 51
MAGNADYNE 32, 49
MAGNAFON 49
MAGNAVOX 07, 10, 03, 12, 29
MANESTH 39, 46
MARANTZ 07
1
Input the 2-digit manufacturer code.
Press the number buttons (0 to 9) to input the code while
pressing TV CONTROL .
MARK 07
Note
DUMONT 53
ELIN 07
ELITE 41
MATSUI 07, 39, 40, 42, 44, 47, 48
MCMICHAEL 34
MEDIATOR 07
• The factory default setting is 00 (PIONEER).
ELTA 44
EMERSON 42
ERRES 07
MEMOREX 44
METZ 31
• If you make a mistake when inputting the code,
release TV CONTROL then start over from the
beginning.
MINERVA 31, 53
MITSUBISHI 09, 10, 02, 21, 31
MULTITECH 44, 49
NEC 59
NECKERMANN 31, 07
NEI 07, 42
FERGUSON 07, 36, 51
FINLANDIA 35, 43, 54
FINLUX 32, 07, 45, 48, 53, 54
FIRSTLINE 40, 44
FISHER 32, 35, 38, 45
FORMENTI 32, 07, 42
FRONTECH 31, 42, 46
FRONTECH/PROTECH 32
FUJITSU 48
• When there are multiple codes for a manufacturer, try
inputting them in the indicated order until the TV can
be operated.
NIKKAI 05, 07, 41, 46, 48
NOBLIKO 49
2
Check that the TV can be operated.
Operate the TV using TV CONTROL.
NOKIA 32, 42, 52
NORDMENDE 32, 36, 51, 52
OCEANIC 31, 32, 42
ORION 32, 07, 39, 40
OSAKI 41, 46, 48
OSO 41
– Press to turn the TV’s power on and off.
INPUT SELECT – Press to switch the TV’s input.
CH +/– – Press to select the TV channel.
VOL +/– – Press to adjust the volume.
FUNAI 40, 46, 58
GBC 32, 42
GE 00, 01, 08, 07, 10, 11, 17, 02,
28, 18
GEC 07, 34, 48
GELOSO 32, 44
GENERAL 29
GENEXXA 31, 41
OSUME 48
OTTO VERSAND 31, 32, 07, 42
PALLADIUM 38
PANAMA 46
GOLDSTAR 10, 23, 21, 02, 07, 50 PANASONIC 31, 07, 08, 42, 22
GOODMANS 07, 39, 47, 48, 56
PATHO CINEMA 42
GORENJE 38
PAUSA 44
24
En
Download from Www.Somanuals.com. All Manuals Search And Download.
PHILCO 32, 42
PHILIPS 31, 07, 34, 56, 68
PHOENIX 32
SONOLOR 31, 35
SONTEC 07
SONY 04
03
PHONOLA 07
PROFEX 42, 44
PROTECH 07, 42, 44, 46, 49
QUELLE 31, 32, 07, 42, 45, 53
R-LINE 07
SOUNDWAVE 07
STANDARD 41, 44
STERN 31
SUSUMU 41
SYSLINE 07
RADIOLA 07
TANDY 31, 41, 48
RADIOSHACK 10, 23, 21, 02
RBM 53
TASHIKO 34
TATUNG 07, 48
RCA 01, 10, 15, 16, 17, 18, 61, 62, TEC 42
09
TELEAVIA 36
REDIFFUSION 32, 42
TELEFUNKEN 36, 37, 52
REX 31, 46
TELETECH 44
ROADSTAR 41, 44, 46
SABA 31, 36, 42, 51
SAISHO 39, 44, 46
SALORA 31, 32, 42, 43
SAMBERS 49
TENSAI 40, 41
THOMSON 36, 51, 52, 63
THORN 31, 07, 42, 45, 48
TOMASHI 18
TOSHIBA 05, 02, 26, 21, 53
SAMSUNG 07, 38, 44, 46, 69, 70 TOWADA 42
SANYO 35, 45, 48, 21, 14, 91
SBR 07, 34
SCHAUB LORENZ 42
SCHNEIDER 07, 41, 47
SEG 42, 46
ULTRAVOX 32, 42, 49
UNIDEN 92
UNIVERSUM 31, 07, 38, 42, 45,
46, 54
VESTEL 07
SEI 32, 40, 49
SELECO 31, 42
VICTOR 13
VOXSON 31
SHARP 02, 19, 27, 67, 90
SIAREM 32, 49
SIEMENS 31
SINUDYNE 32, 39, 40, 49
SKANTIC 43
SOLAVOX 31
WALTHAM 43
WATSON 07
WATT RADIO 32, 42, 49
WHITE WESTINGHOUSE 07
YOKO 07, 42, 46
ZENITH 03, 20
SONOKO 07, 44
25
En
Download from Www.Somanuals.com. All Manuals Search And Download.
CPhlaapteyr b4 ack
04
• When a BD with usage restrictions set by a BD
recorder is loaded, the PIN code input screen
appears. In this case, input your PIN code.
3
Press PLAY to play the disc.
• To pause, press PAUSE during playback.
• To stop, press STOP during playback.
Note
• Some discs start playing automatically when the disc
tray is closed.
• DVD-Video discs have parental lock features. Input
the password registered in the player’s settings to
unlock the parental lock. For details, see page 46.
If the disc menu is displayed
For some discs, the disc menu is displayed automatically
when playback starts. The contents of the disc menu and
the way to operate depend on the disc.
Resuming playback from where it
was stopped (resume playback
function)
• When STOP is pressed during playback, the point
at which the disc stopped is stored in the memory.
When PLAY is pressed after that, playback
resumes from that point.
• To cancel the resume playback function, press
STOP while playback is stopped.
Playing discs or files
Note
• The resume playback function is canceled
automatically in the following cases:
This section describes the player’s main operations.
For the types of discs and files that can be played, see
page 7. Video, image and audio files recorded on discs
are played with the Home Media Gallery (page 34).
– When the disc tray is opened.
– When the file list window is switched.
– When the power is turned off. (For BDs and DVDs
this does not cancel the resume playback
function.)
1
Press STANDBY/ON to turn on the power.
Turn the TV’s power on and switch its input beforehand.
2
Press OPEN/CLOSE to open the disc tray and
• When you want to continue playback from a position
you specify to be played next time, see Continuing
playback from a specified position (Continued Viewing
Playback) on page 33.
load the disc.
Note
• The resume playback function cannot be used for
some discs.
• Load the disc with the printed side facing
up.
• Several dozen seconds are required to read
the disc. Once reading is completed, the
type of disc is displayed on the player’s front
panel display.
26
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Forward and reverse
scanning
Playing a specific section
within a title or track
repeatedly (A-B Repeat)
Use this procedure to play a specific section within a title
or track repeatedly.
04
During playback, press REV or FWD.
• The scanning speed switches each time the button is
pressed. The speed steps depend on the disc or file
(the speed is displayed on the TV screen).
1
During playback, press A-B to select the starting
point.
To resume normal playback
• A- is displayed on the TV screen.
Press PLAY.
2
During playback, press A-B to select the ending
point.
Playing specific chapters or
tracks
• A-B Repeat playback starts.
To cancel A-B Repeat play
• Press A-B during the A-B Repeat play.
Input the number of the title, chapter or track you
want to play.
• Use the number buttons (0 to 9) to input the number,
then press ENTER.
Note
• A-B Repeat play is canceled in the following cases:
– When you search outside of the repeat range.
– When you start other Repeat Play or Random Play.
• Press CLEAR to clear the values you have input.
Skipping content
Playing repeatedly
(Repeat Play)
Use this procedure to play the currently playing disc, title,
chapter, track or file repeatedly.
During playback, press or .
• When is pressed, the playback skips ahead to the
beginning of the next chapter/track/file.
• When is pressed while a video or audio file is
playing, the playback skips back to the beginning of
the currently playing chapter/track/file. Press twice to
skip back to the beginning of the previous chapter/
track/file.
During playback, press REPEAT.
• Each time you press REPEAT the type of repeat
modes changes as shown below.
BD
• When is pressed while an image file is playing,
Current chapter Current title
playback returns to the previous file.
DVD
Playing in slow motion
Current chapter Current title All titles
CD/Video file/Audio file/Image file
Current track/file All titles
While playback is paused, press and hold /
or /.
To cancel Repeat Play
• Press REPEAT several times during Repeat Play.
• The speed switches each time the button is pressed
(the speed is displayed on the TV screen).
To resume normal playback
Note
Press PLAY.
• Repeat Play is canceled in the following cases:
– When you search outside the repeat range.
– When you start other Repeat Play or Random Play.
Step forward and step
reverse
While playback is paused, press / or /.
• The picture moves a step forward or reverse each time
the button is pressed.
To resume normal playback
Press PLAY.
27
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting the bookmark
Playing in the desired order
(Programmed Play)
04
Select the bookmark you want to delete, then
press CLEAR.
• Bookmarks may not be allowed to make for some
discs.
1
During playback, press PROGRAM.
• The program screen is displayed.
• Bookmarks are canceled in the following cases:
– When the player’s power turned off.
– When the disc tray is opened.
2
Select the program number.
Use / to select, then press ENTER.
3
Select the title you want to play.
Use / to select, then press .
Zoom
4
Select the chapter you want to play.
Use / to select, then press ENTER.
During playback, press ZOOM.
• Each time you press ZOOM, the zoom level changes
as shown below.
5
Press PLAY.
• Playback starts.
Zoom 2x Zoom 3x Zoom 4x Zoom 1/2x
Zoom 1/3x Zoom 1/4x Normal (not displayed)
Editing the program
1
Select the program number you want to edit,
Note
then press ENTER.
• This function does not work with some discs.
2
Select title/chapter, then press ENTER.
Displaying thumbnail
images
Deleting the program
Select the program number you want to delete,
then press CLEAR.
Displaying the thumbnails of the image files on the disc.
• To delete all the programs, press
RETURN.
During playback, press INDEX.
• Display the thumbnail of image files. The maximum
number is 12 at once.
Note
• If you select one of the image and press ENTER,
slideshow will start from the image you selected.
• When you use audio CDs for Programmed Play, enter
the track number in step 3.
• This function does not work with BDs.
Switching the camera angles
For BD-ROM and DVD-Video discs on which multiple
angles are recorded, the angles can be switched during
playback.
Making bookmarks
You can make bookmarks on the video currently playing
and play back the scene later.
During playback, press ANGLE.
During playback, press BOOKMARK.
• The bookmark is made.
• The current angle and total number of recorded
angles are displayed on the TV screen.
To switch the angles, press ANGLE again.
• Maximum number of bookmarks are 12.
• The angles can also be switched by selecting Angle
from the FUNCTION menu.
Playing the bookmarked scene
• If the angles are not switched when ANGLE is
pressed, switch them from the disc menu screen.
1
Press and hold BOOKMARK for a few seconds.
• The list of bookmarks is displayed.
2
Select the bookmark you want to play.
Use / to select, then press ENTER.
28
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Group 3 Belarusian(be/bel), Bulgarian(bg/bul), Macedonian(mk/
mkd), Moldavian(mo/mol), Russian(ru/rus), Serbian(sr/
srp), Ukrainian(uk/ukr)
Switching the subtitles
For discs or files on which multiple subtitles are recorded,
the subtitles can be switched during playback.
04
Group 4 Greek(el/ell)
Group 5 Estonian(et/est), Kurdish(ku/kur), Turkish(tr/tur)
Caution
• The subtitles cannot be switched for discs recorded
by a DVD or BD recorder. Also refer to the operating
instructions for the device used for recording.
Note
• Depending on the file, the external subtitles may not
be displayed properly.
During playback, press SUBTITLE.
• The current subtitle and total number of recorded
subtitles are displayed on the TV screen.
To switch the subtitle, press SUBTITLE again.
Displaying the disc
information
• The subtitles can also be switched by selecting
Subtitle from the FUNCTION menu.
Press DISPLAY.
The disc information appears on the TV screen. To switch
• If the subtitles are not switched when SUBTITLE is
pressed, switch them from the disc menu screen.
off the information display, press DISPLAY again.
The information display differs between during playback
and when playback is stopped.
Turning the subtitles off
Switching the audio and
secondary audio
Press SUBTITLE several times or select Subtitle
from the FUNCTION menu to switch the setting to
Off.
For discs or files on which multiple audio streams/
channels are recorded, audio streams/channels can be
switched during playback. Also use this procedure to
switch the secondary audio for BD-ROMs on which
secondary audio is recorded.
About displaying external subtitle
files while playing DivX media files
In addition to the subtitles recorded in DivX media files,
this player also supports the display of external subtitle
files. If a file has the same name as that of a DivX media
file aside from the file extension and the extension is one
of the extensions listed below, the file is treated as an
external subtitle file. Note that DivX media files and
external subtitle files must be located in the same folder.
Only one external subtitle file can be displayed on this
player. Use a computer, etc., to delete any external
subtitle files you do not want to display from the disc.
During playback, press AUDIO/2nd AUDIO.
• The current audio and total number of recorded audio
streams are displayed on the TV screen.
To switch the audio, press AUDIO/2nd AUDIO again.
• The audio/secondary audio can also be switched by
selecting Audio or Secondary Audio from the
FUNCTION menu.
• If the audio/secondary audio is not switched when
AUDIO/2nd AUDIO is pressed, switch it from the
disc menu screen.
.srt, .sub, .txt, .smi, .ssa, .ass
If the language code is specified for the external subtitle
file, the subtitles are displayed with the font
corresponding to that language code. If no language
code is specified, the subtitles are displayed with the font
corresponding to the language code set at Subtitle
Language (page 42). The same font is used for all the
languages in each of the groups below.
Turning the Secondary Audio off
Press 2nd AUDIO several times or select
Secondary Audio from the FUNCTION menu to switch
the setting to Off.
Group 1 Afrikaans(af/afr), Basque(eu/eus), Catalan(ca/cat),
Danish(da/dan), Dutch(nl/nld), English(en/eng),
Faroese(fo/fao), Finnish(fi/fin), French(fr/fra), Galician(gl/
glg), German(de/deu), Guarani(gn/grn), Icelandic(is/isl),
Irish(ga/gle), Italian(it/ita), Latin(la/lat), Norwegian(no/
nor), Portuguese(pt/por), Rhaeto-Romance(rm/roh),
Scots-Gaelic(gd/gla), Spanish(es/spa), Swahili(sw/swa),
Swedish(sv/swe), Zulu(zu/zul)
Group 2 Albanian(sq/sqi), Croatian(hr/hrv), Czech(cs/ces),
Hungarian(hu/hun), Polish(pl/pol), Romanian(ro/ron),
Slovak(sk/slk), Slovenian(sl/slv)
29
En
Download from Www.Somanuals.com. All Manuals Search And Download.
• If a USB memory device containing other data
(previously recorded) is used, the video and audio
may not play back properly.
Switching the secondary
video
Use the procedure below to switch the secondary video
(Picture-in-Picture) recorded on the BD-ROM.
04
• Do not disconnect the USB memory device while
playback is in progress.
• Some time may be required for the data to load (read/
write).
During playback, press 2nd VIDEO.
• The current secondary video and total number of
recorded secondary video streams are displayed on
the TV screen.
Caution
To switch the secondary video, press 2nd VIDEO
again.
• It may not be possible to use the BONUSVIEW and
BD-LIVE functions if there is insufficient space on the
USB memory device. In this case, refer to Erasing data
that has been added to BDs and application data on
page 45 for erasing the Virtual Package data and the
BD-LIVE data in the USB memory device.
Note
• Operation of USB memory devices is not guaranteed.
Primary audio/video
• Playback of BD-LIVE function data differs depending
on the disc used. For details, consult the user
instructions supplied with the disc.
Secondary audio/video
• The secondary video can also be switched by
selecting Secondary Video from the FUNCTION
menu.
• To enjoy the BD-LIVE function, a network connection
and settings are required (pages 21 and 44).
• If the secondary video is not switched when 2nd
VIDEO is pressed, switch it from the disc menu
screen.
• BD-LIVE is a function that provides for connection to
the Internet. Discs supporting the BD-LIVE function
may send ID codes identifying this player and the disc
to the contents provider via the Internet.
Turning the Secondary Video off
Press 2nd VIDEO several times or select
Secondary Video from the FUNCTION menu to switch
the setting to Off.
Enjoying BONUSVIEW or
BD-LIVE
This player is compatible with BD-Video BONUSVIEW
and BD-LIVE.
When using BD-Video discs compatible with
BONUSVIEW, you can enjoy such functions as secondary
video (picture in picture) (above) and secondary audio
(page 29). With BD-Video discs supporting BD-LIVE,
special video images and other data can be downloaded
from the Internet.
Data recorded on BD video and downloaded from BD-
LIVE is stored on the USB memory device (external
memory). To enjoy these functions, connect a USB
memory device (minimum 1 GB capacity, 2 GB or greater
recommended) supporting USB 2.0 High Speed (480
Mbit/s) to the USB port.
• When you insert or remove a USB memory device, be
sure to turn the player’s power off.
• To recall data stored in the USB memory device, first
insert the disc media that was being used at the time
the data was downloaded (if a different disc is loaded,
the data stored on the USB memory device cannot be
played).
30
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback functions
04
The functions that can be used differ according to the type of disc and file. In some cases, some of the functions cannot
be used. Check the usable functions on the table below.
Disc/file type
DVD-R
/-RW
(VR
1
Function
DVD-
BD-
ROM
BD-R
/-RE
DVD-
Video
Video Image Audio Audio
AVCREC AVCHD
2
file
file
file
CD
Audio
format)
Forward and reverse
4
4
4
4
4
4
4
4
5
5
3
scanning
Playing specific titles,
chapters or tracks
Skipping content
3,6
7
Slow motion play
Step forward and step
8
3
reverse
3
A-B Repeat play
Repeat Play
Zoom
9
Angle
10
Subtitle
11
Audio
12
13
Secondary audio
14
15
Secondary video
Disc information
1. Some functions may not work for some discs or files, even if indicated [] on the table.
2. Except BDP-140.
3. For some discs, normal playback resumes automatically when the chapter switches.
4. No sound is produced during forward and reverse scanning.
5. Sound is produced during forward and reverse scanning.
6. • No sound is output during slow motion playback.
• It is not possible to switch the speed during reverse slow motion playback.
7. Reverse slow motion playback is not possible.
8. Reverse step playback is not possible.
9. Angle mark is displayed for scenes at which multiple angles are recorded if Angle Mark is set to On (page 42).
10. • The types of recorded subtitles depend on the disc and file.
• In some cases, the subtitle may switch or the switching screen provided on the disc may be displayed immediately, without the current
subtitle or the total number of subtitles recorded on the disc being displayed.
11. The types of recorded audio streams depend on the disc and file.
12. • The types of recorded secondary audio streams depend on the disc and file.
• In some cases, the secondary audio may switch or the switching screen provided on the disc may be displayed immediately, without the
current secondary audio or the total number of secondary audio streams recorded on the disc being displayed.
• Secondary audio mark is displayed for scenes at which secondary audio is recorded if Secondary Audio Mark is set to On (page 42).
13. Some discs do not include secondary audio.
14. • In some cases, the secondary video may switch or the switching screen provided on the disc may be displayed immediately, without the
current secondary video or the total number of secondary video streams recorded on the disc being displayed.
• Secondary video mark is displayed for scenes at which secondary video is recorded if PIP Mark is set to On (page 42).
15. Some discs do not include secondary video.
31
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
Description
Using the FUNCTION
menu
Various functions can be called out according to the
player’s operating status.
04
Ins Replay
Slide Show
Skip backward 10 seconds.
Switch the playback speed while playing
the picture slide show.
Transition
Change the style of the slide show while
playing the picture slide show.
1
Display the FUNCTION menu.
* The items shown on the FUNCTION menu depend on
the type of the disc.
Press FUNCTION during playback.
2
Select and set the item.
Use / to select, then press ENTER.
Note
• Selectable items depend on the type of disc.
Note
• Items that cannot be changed are displayed in gray.
The items that can be selected depend on the player’s
status.
Playing from a specific time
(Time Search)
To change the setting of the
selected item
1
Select Time.
Use / to select, then press ENTER.
2
Input the time.
Use / to change.
Use the number buttons (0 to 9) to input the time.
To close the FUNCTION menu
Press FUNCTION.
• To play from 45 minutes, input 0, 0, 4, 5, 0 and 0, then
press ENTER.
• To play from 1 hour 20 minutes, input 0, 1, 2, 0, 0 and
0, then press ENTER.
FUNCTION menu item list
Item
Description
• Press CLEAR to clear the values you have input.
Video Adjust
(BDP-LX55)
Display the picture quality adjustment
screen (page 44).
3
Starting playback from the specified time.
Press ENTER.
Title
Display the title information for the
currently playing disc and total number
of titles on the disc. Also select the title
you want to play. (See the following
description.)
Playing a specific title,
chapter or track (Search)
Chapter (track/file)
Display the information for the currently
playing chapter (track/file) and total
number of chapters in the disc. Also
select the chapter (track/file) you want to
play. (See the following description.)
1
Select Title or Chapter (track/file).
Use / to select, then press ENTER.
2
Input the Title or Chapter (track/file) number.
Use the number buttons (0 to 9) or / to input the
number.
Time
Display the elapsed or remaining time.
Also enter the time from which you want
to start playback. (See the following
description.)
• To search for title 32, input 3 and 2, then press
ENTER.
• Press CLEAR to clear the values you have input.
Play Mode
Audio
Switch the play mode (page 33).
Switch the audio.
3
Starting playback from the specified title, chapter
or track.
Press ENTER.
Angle
Switch the BD-ROM/DVD-Video disc’s
camera angle.
Subtitle
Switch the subtitle language.
Switch the subtitle code page.
Code Page
Second Video
Switch the BD-ROM’s secondary video
(Picture-in-Picture) (page 30).
Second Audio
Bitrate
Switch the BD-ROM’s secondary audio
(page 29).
Display the bitrate of the audio/video/
secondary video/secondary audio.
Still off
Switch off the BD-ROM’s still picture.
Skip forward 30 seconds.
Ins Search
32
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing specified range of
discs, titles or chapter (track/
file) in random order
04
You can select from 2 types of random playback.
1
Select Play Mode.
Use / to select, then press ENTER.
2
Select the playing mode.
Use / to select, then press ENTER.
Random play
The specified range of discs, titles or chapter (track/file) is
played in random order. The same item may be played
consecutively.
Shuffle play
The specified range of discs, titles or chapter (track/file) is
played in random order. Each item is played once.
Continuing playback from a
specified position
(Continued Viewing
Playback)
This function allows you to continue playback from a
position you specify to be played next time, even after
turning the power off.
Setting
During playback, press CONTINUED at the
position from which you want to start continued
viewing playback.
The elapsed playing time at the specified position is
displayed on the TV screen.
Playing
1
Press PLAY to play the title for which you have
set continued viewing playback.
The FUNCTION menu screen appears automatically to
show the point (time) when you pressed CONTINUED.
• The Function control screen can also be displayed by
pressing FUNCTION during playback.
2
Press ENTER, then select the specified continued
viewing playback time.
Playback starts from the specified position.
Note
• The continued viewing playback setting is canceled
when OPEN/CLOSE is pressed.
• Continued viewing playback may not work properly
with some discs.
33
En
Download from Www.Somanuals.com. All Manuals Search And Download.
CPhlaapteyr b5 ack from Home Media Gallery
05
• The following files are allowed to be played from
Home Media Gallery:
– PCs running Microsoft Windows Vista or XP with
Windows Media Player 11 installed
– PCs running Microsoft Windows 7 with Windows
Media Player 12 installed
– DLNA-compatible digital media servers (on PCs or
other components)
– Files stored in a PC or DMS (Digital Media Server)
as described above can be played by Digital Media
Player (DMP).
The player supports the use of such DMP.
About Home Media
Gallery
• To play back audio files stored on components on the
network, you must turn on the DHCP server function
of your router. In case your router does not have the
built-in DHCP server function, it is necessary to set up
the network manually. Otherwise, you cannot play
back files stored on components on the network. See
page 44.
About network playback
This player’s Home Media Gallery function allows you to
display a list of input sources and start playback. This
The network playback function of this unit uses the
chapter describes setup and playback procedures
following technologies:
required to enjoy these features. When you play the files
stored on your computer or the components on the
Windows Media Player
network, it is advisory that you also refer to the operation
See Windows Media Player 11/Windows Media Player 12
manual supplied with your network component.
above for more on this.
The input sources that can be played from Home Media
Gallery are as shown below.
Windows Media DRM
• BD-R/RE (BDAV format) discs
Microsoft Windows Media Digital Rights Management
(WMDRM) is a platform to protect and securely deliver
content for playback on computers, portable devices and
network devices. Home Media Gallery functions as a
WMDRM 10 for networked devices. WMDRM protected
content can only be played on media servers supporting
WMDRM.
• DVD-R/RW (VR format) discs
• Audio CDs (CD-DA, SACD and DTS CDs)
• DVD/CDs on which only data files of video, image or
audio files, etc. are recorded.
• USB memory device
Content owners use WMDRM technology to protect their
intellectual property, including copyrights. This device
uses WMDRM software to access WMDRM protected
content. If the WMDRM software fails to protect the
content, content owners may ask Microsoft to revoke the
software’s ability to use WMDRM to play or copy
protected content. Revocation does not affect
unprotected content. When you download licenses for
protected content, you agree that Microsoft may include
a revocation list with the licenses. Content owners may
require you to upgrade WMDRM to access their content.
If you decline an upgrade, you will not be able to access
content that requires the upgrade. This product is
protected by certain intellectual property rights of
Microsoft. Use or distribution of such technology outside
of this product is prohibited without a license from
Microsoft.
• Files on the network servers (on the PCs or
components connected to the player via LAN
interface.)
Note
• The Home Media Gallery allows you to play files on
media servers connected on an identical Local Area
Network (LAN) as the receiver.
34
En
Download from Www.Somanuals.com. All Manuals Search And Download.
DLNA
Disclaimer for Third Party Content
Access to content provided by third parties requires a
high speed Internet connection and may also require
account registration and a paid subscription.
05
Third party content services may be changed, suspended,
interrupted, or discontinued at any time without notice,
and Pioneer disclaims any liability in connection with
such occurrences.
DLNA CERTIFIED® Audio Player
Pioneer does not represent or warrant that content
services will continue to be provided or available for a
particular period of time, and any such warranty, express
or implied, is disclaimed.
The Digital Living Network Alliance (DLNA) is a cross-
industry organization of consumer electronics,
computing industry and mobile device companies.
Digital Living provides consumers with easy sharing of
digital media through a wired or wireless network in the
home.
About playback behavior over a
network
The DLNA certification logo makes it easy to find
products that comply with the DLNA Interoperability
Guidelines. This unit complies with DLNA Interoperability
Guidelines v1.5. When a PC running DLNA server
software or a DLNA compatible device is connected to
this player, some setting changes of software or other
devices may be required. Please refer to the operating
instructions for the software or device for more
information.
• Playback may stall when the PC is switched off or any
media files stored on it are deleted while playing
content.
• If there are problems within the network environment
(heavy network traffic, etc.) content may not be
displayed or played properly (playback may be
interrupted or stalled). For best performance, a
10BASE-T/100BASE-TX connection between the
player and the PC is recommended.
DLNA®, the DLNA Logo and DLNA CERTIFIED® are
trademarks, service marks, or certification marks of the
Digital Living Network Alliance.
• If several clients are playing simultaneously, as the
case may be, playback is interrupted or stalled.
• Depending on the security software installed on a
connected PC and the setting of such software,
network connection may be blocked.
Content playable over a network
• Even when encoded in a compatible format, some
files may not play correctly.
Pioneer is not responsible for any malfunction of the
player and/or the Home Media Gallery features due to
communication errors/malfunctions associated with
your network connection and/or your PC, or other
connected equipment. Please contact your PC
manufacturer or Internet service provider.
• Some functions may not be supported depending on
the server type or version used.
• Supported file formats vary by server. As such, files
not supported by your server are not displayed on this
unit. For more information check with the
manufacturer of your server.
Windows Media is either a registered trademark or
trademark of Microsoft Corporation in the United States
and/or other countries.
This product includes technology owned by Microsoft
Corporation and cannot be used or distributed without a
license from Microsoft Licensing, Inc.
Microsoft®, Windows®7, Windows®Vista, Windows®XP,
Windows®2000, Windows®Millennium Edition,
Windows®98, and WindowsNT® are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
35
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing back image files
DLNA Search
05
Playing back the files stored on the components
connected to the player via network.
About Slideshow
A display of the files on the disc or in the folder switches
automatically.
1
Press HOME MEDIA GALLERY to display the
Home Media Gallery.
The Home Media Gallery can also be displayed by
selecting Home Media Gallery from Home Menu, then
pressing ENTER.
Note
• When playing an audio CD (CD-DA/SACD/DTS-CD),
the Now Playing screen is displayed.
2
Select DLNA Search.
• Some BD-R/-RE discs have playback protection. To
cancel the protection, input the password set for the
disc.
Use / to select, then press ENTER.
3
Select the server which contains the file you want
to play.
• It may take a few seconds before playback starts. This
is normal.
4
Select the file you want to play.
Use / to select, then press ENTER.
• It may not be possible to play some files properly.
• The number of views may be restricted.
Note
• This player does not support DTCP-IP.
Recorded files and contents that are protected by
digital copyright protection cannot be played via LAN
interface.
Playing in the desired
order (Playlist)
The discs that can add tracks and files to the Playlist are
as shown below.
Disc/USB playback
• DVDs/CDs/USB memory devices on which audio files
are recorded
1
Press HOME MEDIA GALLERY to display the
Home Media Gallery.
Adding tracks/files
Use this procedure to add tracks and files, and create the
The Home Media Gallery can also be displayed by
selecting Home Media Gallery from Home Menu, then
pressing ENTER.
Playlist.
2
Select Disc or USB.
1
Press HOME MEDIA GALLERY to display the
Use / to select, then press ENTER.
Home Media Gallery.
The Home Media Gallery can also be displayed by
selecting Home Media Gallery from Home Menu, then
pressing ENTER.
3
Select Photo/Music/Video/AVCHD.
Use / to select, then press ENTER.
• This step is not for the discs that have been recorded
with BDAV/VR/AVCREC format.
2
Select Disc or USB.
Load the disc beforehand.
• To play files in AVCHD format on a USB memory
device, create a folder named “AVCHD” on the USB
memory device, then copy the “BDMV” folder
containing which the files to be played into the
“AVCHD” folder.
Use / to select, then press ENTER.
3
Select the track/file to be added.
Use to select.
4
Press POP UP MENU to display the POP UP MENU
4
Select the title/track or file you want to play.
menu.
Use / to select, then press ENTER.
5
Select Add to Playlist to add to Playlist.
Playback starts from the selected title/track or file.
Use / to select, then press ENTER.
• If the file you want to play is in the folder, select the
folder that contains the file first.
The track or file selected in step 3 is added to the Playlist.
• To add more tracks or files, repeat steps 3 to 5.
36
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playing the Playlist
05
1
Press HOME MEDIA GALLERY to display the
Home Media Gallery.
The Home Media Gallery can also be displayed by
selecting Home Media Gallery from Home Menu, then
pressing ENTER.
2
Select Playlist.
Use/ to select, then press ENTER.
3
Select the track/file to be played.
Use/ to select, then press ENTER.
Playback starts from the selected track/file and continues
until the end of the list is reached. Use / to play
the previous or next track/file. The Now Playing screen is
displayed.
Deleting tracks/files from
the Playlist
1
Select the track/file to be deleted, then press POP
UP MENU to display the POP UP MENU menu.
2
Use / to select Delete from Playlist, then press
ENTER.
37
En
Download from Www.Somanuals.com. All Manuals Search And Download.
CPhlaapteyr i6ng the web contents
06
You can enjoy some streaming contents on the Internet
with the player.
• Access to content provided by third parties requires a
high speed Internet connection and may also require
account registration and a paid subscription.
Third party content services may be changed,
suspended, interrupted, or discontinued at any time
without notice, and Pioneer disclaims any liability in
connection with such occurrences.
Available web
contents
Pioneer does not represent or warrant that content
services will continue to be provided or available for a
particular period of time, and any such warranty,
express or implied, is disclaimed.
• YouTube (MPEG4 AVC H.264)
• Picasa
Note
About YouTube
Playing the items
• YouTube videos of the following sizes can be played.
– Standard quality (400 x 226 pixels, 200 kbps)
– Medium quality (480 x 360 pixels, 512 kbps)
– High quality (854 x 480 pixels, 900 kbps)
– HD (720p) (1280 x 720 pixels, 2 Mbps)
– HD (1080p) (1920 x 1080 pixels, 4 Mbps)
• This player supports the YouTube Leanback service.
The Youtube Leanback service is only available in
English for now.
support/youtube/ for further information.
Caution
You must connect the player to the Internet beforehand.
See Connecting to the network through LAN interface on
page 21 for the details.
• YouTube videos for mobile phones cannot be played.
• Some YouTube videos cannot be played.
About Picasa
1
Display the selection screen.
The selection screen can be selected by pressing
• Picasa is available only in English. Refer to
details.
HOME MENU then selecting Web Contents
Desired web content.
– Register your user name and password on the PC
before you use Picasa Web Albums.
2
Select the type of web contents.
Use / to select, then press ENTER.
– When you access Picasa from this player for the
first time, select the New User icon and enter your
registered user name and password.
3
Press / to select the item you want to play,
then press ENTER.
To stop playback, press EXIT. Playback of the video stops
and the Home Menu screen reappears.
• Depending on the Internet connection environment,
it may not be possible to play web contents properly.
• To access to web contents, this player requires a
broadband Internet connection. A contract with an
Internet provider is required for a broadband Internet
connection.
38
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 7
07
Advanced settings
Changing the settings
Operating the Initial Setup
screen
1
When playback is stopped, display the Home
Menu screen.
Press HOME MENU.
Select and set Initial Setup.
2
Use / to select, then press ENTER.
3
Select the item and change the setting.
Use /// to select, then press ENTER.
Closing the Initial Setup screen
Press
HOME MENU or
RETURN.
Note
• The items that can be selected depend on the player’s status.
• In Options, the factory default settings are indicated in bold.
Setting
Options
Explanation
Select this when connecting to a wide (16:9) TV.
TV Screen
16:9 Full
16:9 Normal
Select this when connected to a wide (16:9) TV. 4:3 pictures are displayed
with vertical black bars along the sides.
4:3 Pan&Scan
4:3 Letterbox
Select this when connecting to a 4:3 screen TV and playing a 16:9 video. The
video will be played with the left and right sides of the image cut off to display
on the 4:3 screen. (This function works if the disc is labeled for 4:3PS.)
Select this when connecting to a 4:3 screen TV and playing a 16:9 video. The
video will be played with black bands at the top and bottom.
Video Adjust
The quality of the playback picture can be adjusted according to the TV you are using (page 44).
Stream Smoother
(BDP-LX55)
Auto
Select this to automatically correct compressed video files on the network, a
disc or a USB memory device and play them with a more natural picture
quality.
Off
Sharpness
High
Middle
Low
Standard
Vivid
Cinema
Custom
0
Choose the level of sharpness.
Choose the video output mode.
(Except BDP-LX55)
Video Mode
(Except BDP-LX55)
Noise Reduction
Choose the level of noise reduction.
(Except BDP-LX55)
1
2
3
39
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Options
Bitstream
PCM
Explanation
07
Digital Output
Select this to output digital audio signals directly.
Select this to output digital audio signals converted to PCM audio signals.
Select this to output digital audio signals converted to DTS Digital Surround.
Select this to output audio signals other than digital audio signals.
Re-encode
Off
DTS Downmix (BDP-LX55) Stereo
DTS-HD Master Audio signals, DTS-HD High Resolution Audio signals or
DTS Digital Surround audio signals converted to linear PCM audio signals
are converted into 2-channel (stereo) signals for output.
Lt/Rt
DTS-HD Master Audio signals, DTS-HD High Resolution Audio signals or
DTS Digital Surround audio signals converted to linear PCM audio signals
are converted into 2-channel signals compatible with Dolby Surround for
output (when the connected AV receiver or amplifier, etc., is compatible with
Dolby Pro Logic, the AV receiver or amplifier outputs the linear PCM audio
signals as surround audio signals).
Downsampling
48k
96k
Select this when playing a disc recorded with a sampling frequency of 48 kHz.
Select this when playing a disc recorded with a sampling frequency of 96 kHz.
192k
Select this when playing a disc recorded with a sampling frequency of 192
kHz.
DRC (Dynamic Range
Control)
Off
Select this to output audio signals without using the DRC function.
On
Select this to adjust the range between the loudest and softest sounds
(dynamic range) for playback at average volume. Use this when it is hard to
hear dialog or when watching movies at midnight.
* Only Dolby digital and
analog audio signals are
supported.
Auto
Select to switch the DRC setting On/Off automatically according to the input
audio signal from the disc.
40
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Options
Single
Explanation
07
HDMI Mode (BDP-LX55)
Select this when an HDMI cable is connected to HDMI OUT (MAIN) terminal only.
Select this when HDMI cables are connected to both HDMI OUT terminals.
Separate
Pure Audio
Select this to enjoy music only with a better sound quality when devices are
connected to both HDMI output terminals. With this setting, music is output
from the HDMI OUT (SUB) terminal only, and video signals are only output
from the HDMI OUT (MAIN) terminal when DISPLAY is pressed.
Also refer to Setting the HDMI Mode (Only for BDP-LX55) on page 16.
Color Space
RGB
Select this to output the video signals as RGB signals. Choose this if the
colors seem too faint and the black seems too bright.
YCbCr
Select this to output the video signals as YCbCr 4:4:4 signals.
Select this to output the video signals as YCbCr 4:2:2 signals.
YCbCr 422
Full RGB
Select this to output the video signals as RGB signals. Choose this if the colors
seem too dense and all the dark colors are displayed in a uniform black.
Resolution
Auto
Select this to choose the resolution of the video signals output from the
HDMI OUT terminal automatically.
480I/576I
Output the video signals from the HDMI OUT terminal with the selected
(Except BDP-LX55) resolution.
The resolution can be changed by pressing HDMI, but Auto cannot be
selected.
480P/576P
720P
1080I
1080P
HDMI Audio Out
Bitstream
PCM
Select this to output HDMI audio signals directly.
Select this to output HDMI audio signals converted to 2-channel audio signals.
Select this to choose the type of audio signals automatically.
Re-encode
Off
Select this when you do not want to output the audio signal from the HDMI
output terminal.
Control
On
Select this to control the player with the remote control of the connected AV
device using an HDMI cable. Also refer to page 16.
Off
Select this when you do not want to control the player with the remote control
of the connected AV device using an HDMI cable.
To use Sound Retriever Link, Stream Smoother Link and PQLS (pages 16 and 17), Control must be set to On.
HDMI Deep color
30bits
36bits
Off
Select this when outputting the video signals with 30-bit color.
Select this when outputting the video signals with 36-bit color.
Select this when outputting the video signals with normal 24-bit color.
HDMI 1080P 24Hz
On
Select this when Resolution is set to Auto or 1080P and outputting 1080p/24
video signals to a TV compatible with 1080p/24.
Off
Select this when Resolution is set to 1080P and outputting 1080p/60 video
signals to a TV compatible with 1080p/60.
HDMI 3D
3D notice
Auto
Off
With 3D discs, the disc is played with 3D images.
Even with 3D discs, the disc is played with 2D images.
This sets whether or not to display the 3D notice when playing 3D images.
Yes
No
IP setting
Select this to set the IP address of the player and DNS server (page 44).
Proxy Server
Information
Only set the proxy server if so instructed by your Internet service provider (page 44).
Displays the values of the MAC address, IP address, subnet mask, default gateway, DNS server
(primary) and DNS server (secondary).
Connection test
Select this to test the network connection (page 45).
Internet Connection
Select this when connecting to the Internet.
Enable
Disable
Select this when not connecting to the Internet.
All discs are allowed to connect to BD-LIVE.
BD-Live connection
DLNA
Permitted
Partial Permitted
Prohibited
Enable
Only discs whose safety has been confirmed are allowed to connect to BD-LIVE.
No disc is allowed to connect to BD-LIVE.
Select this when connecting to DLNA server.
41
En
Disable
Select this when not connecting to DLNA server.
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
OSD
Options
Explanation
07
available languages Choose a language for the on-screen displays from the listed languages.
Audio
available languages Choose a language from the listed languages to set the default audio
language for BD-ROM and DVD-Video playback.
* For some discs, it may not
be possible to change to the
selected language.
If a language not recorded on the BD/DVD is set, one of the recorded languages is automatically selected for playback.
Subtitle
available languages Choose a language from the listed languages to set the default subtitle
language for BD-ROM and DVD-Video playback.
* For some discs, it may not
be possible to change to the
selected language.
If a language not recorded on the BD/DVD is set, one of the recorded languages is automatically selected for playback.
Menu
available languages Choose a language from the listed languages to set the default language for
BD-ROM and DVD-Video menus.
* For some discs, it may not
be possible to change to the
selected language.
If a language not recorded on the BD/DVD is set, one of the recorded languages is automatically selected for playback.
Angle Mark
On
Select this to display the angle mark on the TV screen (page 28). This is the
factory default setting for the BDP-440/BDP-140.
Off
Select this if you do not want to display the angle mark on the TV screen. This
is the factory default setting for the BDP-LX55.
PIP Mark
On
Select this to display the PIP mark on the TV screen. This is the factory default
setting for the BDP-440/BDP-140.
Off
Select this if you do not want to display the PIP mark on the TV screen. This
is the factory default setting for the BDP-LX55.
Secondary Audio Mark
On
Select this to display the secondary audio mark on the TV screen (page 29).
This is the factory default setting for the BDP-440/BDP-140.
Off
Select this if you do not want to display the secondary audio mark on the TV
screen. This is the factory default setting for the BDP-LX55.
DivX(R) VOD DRM
DVD Playback
Registration Code
Displays the player’s registration code required to play DivX VOD files
(page 10).
DVD AUDIO
Select this to play only the audio part on the DVD-Audio disc.
Select this to play only the video part on the DVD-Audio disc.
* This setting is for DVD-
Audio disc playback.
(Except BDP-140)
DVD VIDEO
Internet Setting
Permitted
Web contents can be watched without entering the password.
The password must be entered to watch web contents.
No web contents can be watched.
Partial Permitted
Prohibited
On
Disc Auto Playback
Last Memory
Discs are played automatically after they are loaded.
Loaded discs do not start playing automatically.
Off
On
Select this to save the point at which you last stopped playback, even after the
disc tray is opened or you switch to the standby mode.
Off
Select this when you want to use only Continue Viewing Play (page 33).
PBC (Play Back Control)
On
Select this to play Video-CDs (version 2.0) compatible with PBC using the
disc menu.
Off
Select this to play Video-CDs (version 2.0) compatible with PBC without using
the disc menu.
Setup Navigator
Start making the settings using the Setup Navigator menu. For details, see page 23.
Change Password
Register (change) the password for parental lock settings or for unlocking to play DVD-Videos with
the parental lock feature (page 45).
Parental Control
Country Code
Change the player’s parental lock level (page 46).
Change the Country/Area code (page 46).
42
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Options
Off
Explanation
07
Screen Saver
The screen saver is not activated.
1 min
2 min
3 min
Off
The screen saver will be activated if no operation has been performed for
more than one minute/two minutes/three minutes. Operating the remote
control can deactivate the screen saver.
Auto Power Off
Select this if you do not want the power to turn off automatically.
10 min
20 min
30 min
On
The power will be automatically turned off if no operation has been performed
for more than 10 minutes/20 minutes/30 minutes.
Quick Start
Update
Select to shorten the required time to boot up.
Select to perform normal bootup.
Off
Disc
Select the method of software updating. (page 46)
USB Storage
Network
Load Default
Restore the settings to the factory default.
Check the system version number.
System Information
Disc Auto Update
On
Display the software update screen when the disc with the player’s update
file is loaded.
Off
The software update screen must be displayed manually. (page 46)
BUDA
BUDA Information Display and set up the BUDA data on the connected USB memory device.
BUDA Setup
43
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the video
Setting the IP address
07
1
Select and set Display Setting Video Adjust
1
Select and set Network IP setting Next
Next Screen.
Screen.
Use / to select, then press ENTER.
Use / to select, then press ENTER.
2
Select the item and change the setting.
2
Set IP address.
Use / to select the item, then use / to change the
setting. Once the setting is completed, press
Use /// to set the IP address of the player or DNS
server, then press ENTER.
• Auto Set IP Address
RETURN to close the settings screen.
On – The player’s IP address is obtained
List of BDP-LX55 setting items
automatically. Select this when using a broadband
router or broadband modem that has a DHCP
(Dynamic Host Configuration Protocol) server
function. This player’s IP address will automatically
be allocated from the DHCP server.
Item
Description
Prog.Motion
Adjust according to the type of image
(moving or still image). This is effective
mainly when outputting video materials
as progressive images.
Off – The player’s IP address must be set manually.
Use the number buttons (0 to 9) to input the IP
address, subnet mask and default gateway.
Pure Cinema
This setting optimizes the operation of
the progressive scanning circuit for
playing film materials.
Black level
White level
Hue
Adjusts the level of the black portions.
Adjusts the level of the white portions.
Note
• For information on the DHCP server function, refer to
the operating instructions for the network device.
Adjusts the balance between green and
red.
• You may need to contact your Internet service
provider or network administrator when inputting the
IP address manually.
Chroma Level
Detail
Adjusts the density of the colors.
Adjusts the picture’s contours.
YNR
Reduces noise in the luminance (Y)
signal.
Setting the proxy server
Only set the proxy server if so instructed by your Internet
CNR
Reduces noise in the chroma (C) signal.
service provider.
MNR
Reduces the mosquito noise (distortion
along the contours of the picture
generated upon MPEG compression).
1
Select and set Network Proxy Server Next
Screen.
BNR
Reduces the block noise (block-shaped
distortion generated upon MPEG
compression).
Use / to select, then press ENTER.
2
Select and set Use or Not use at Proxy Server.
Use / to change, then press .
List of BDP-440/BDP-140 setting items
• Use – Select this when using a proxy server.
• Not use – Select this when not using a proxy server.
If you have selected Use, proceed to step 3.
Item
Description
Brightness
Select this to adjust the TV screen’s
brightness.
3
Select and set Server Select Method.
Contrast
Hue
Select this to adjust the TV screen’s
contrast.
Use / to change, then press .
• IP Address – Input the IP address.
• Server Name – Input the server name.
Select this to adjust the color (green and
red) balance of the TV screen.
Saturation
Select this to adjust the TV screen’s
saturation.
Note
• For the BDP-LX55, the Video Adjust settings do not
affect Blu-ray 3D pictures or the pictures of the
VIDEO OUTPUT terminals.
44
En
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Input IP Address or Server Name.
Erasing data that has been added to
BDs and application data
07
Use the number buttons (0 to 9) to input the number if you
select IP address in step 3. Use / to move the cursor.
Use this procedure to erase data that has been added to
BDs (data downloaded with the BD-LIVE function and
data used with the BONUSVIEW function) and
application data.
When Server Name is selected in step 3, use the number
buttons (0 to 9) to launch the software keyboard. Now use
/// to select characters and items, then press
ENTER to input.
5
Input Port Number.
Press , then use the number buttons (0 to 9) to input
the number.
Caution
• Some time is required to erase the data.
• Do not unplug the power cord while data is being
erased.
6
Press ENTER to set.
Displaying the network settings
1
Select and set BUDA BUDA Setup.
Use / to select, then press ENTER.
Select and set Network Information Next
2
Select and set Fmt buda.
Screen.
Press ENTER.
Use / to select, then press ENTER.
The MAC address, IP address, subnet mask, default
gateway and DNS server (primary and secondary)
settings are displayed.
Registering or Changing the
password
When Auto Set IP Address is set to On, the values
obtained automatically are displayed.
Use this procedure to register or change the code
number required for the Parental Lock settings.
About default password of this unit
Note
The default password is “0000”.
• “0.0.0.0” is displayed when each IP address has not
been set.
• This unit might ask you to enter a password when you
change the password.
• If you reset this unit, your password is simultaneously
changed to the default setting.
Testing the network connection
Select and set Network Connection Test
1
Select and set Security Change Password
Start.
Next Screen.
Use / to select, then press ENTER.
Use / to select, then press ENTER.
“Network is OK.” is displayed once the test is completed.
If any other message is displayed, check the connections
and/or settings (pages 21 and 41).
2
Input the password.
Use the number buttons (0 to 9) to input the number, then
press ENTER to set.
Changing to other language at
Use / to move the cursor.
language setting
3
Re-input the password.
Use the number buttons (0 to 9) to input the number, then
press ENTER to set.
1
Select and set Language.
Use / to select, then press ENTER.
Use / to move the cursor.
2
Select and set OSD, Audio, Subtitle or Menu
• To change the password, input the previously
registered password, then input the new password.
Use / to select, then press ENTER.
3
Select and set the desired language.
Use / to select, then press ENTER.
Note
• We recommend making a note of the password.
Note
• If you have forgotten the password, reset the player to
the factory default setting, then register the password
again (page 47).
• If a language not recorded on the BD/DVD is set, one
of the recorded languages is automatically selected
and played.
45
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Parental Lock level for
viewing DVDs/BD-ROMs
Some DVD-Video discs containing scenes of violence, for
example, have Parental Lock levels (check the indications
on the disc’s jacket or elsewhere). To restrict viewing
these discs, set the player’s level to the level lower than
the discs.
Software updating
The player’s software can be updated using one of the
methods shown below.
07
• Connecting to the Internet.
• Using a disc.
• Using a USB memory device.
Product information on this player is provided on the
Pioneer website. Check the website shown on page 6 for
update and service information on your Blu-ray disc
player.
1
Select and set Security Parental Control
Next Screen.
Use / to select, then press ENTER.
2
Input the password.
Use the number buttons (0 to 9) to input the number, then
press ENTER to set.
Caution
• Do not unplug the power cord or remove the USB
memory device/disc during software updating.
Otherwise, the updating will be aborted and
malfunction may occur with the player.
Use / to move the cursor.
3
Change the level.
Use / to change, then press ENTER to set.
• There are two processes for software updating,
downloading and updating. Both processes may take
a certain period of time.
Note
• The level can be set to Off or between Level1 and
Level8. When set to Off, viewing is not restricted.
• Other operations are defeated during software
updating. Furthermore, updating process cannot be
canceled.
Changing the Country/Area code
• On the BDP-LX55/BDP-440, when the front panel
display is off, turn it on with FL DIMMER. When
updating the player’s software with the front panel
display off, do not unplug the power cord until the unit
turns off.
1
Select and set Security Country Code Next
Screen.
Use / to select, then press ENTER.
2
Input the password.
Use the number buttons (0 to 9) to input the number, then
press ENTER to set.
Updating connecting to the Internet
Use / to move the cursor.
Note
3
Change the country/area code.
• Depending on the Internet connection conditions,
downloading may take a long time.
Use / to change, then press ENTER to set. Refer to
page 48.
• Steps 1 to 5 are the operations performed by the user
(they are intended to download the software from the
Internet).
• Steps 6 to 8 are the operations performed
(automatically) by the player (they are intended to
update the software).
1
2
Connect to the Internet.
When playback is stopped, display the Home
Menu screen.
Press HOME MENU.
Select and set Initial Setup.
3
Use / to select, then press ENTER.
4
Select and set Options Update Network
Start.
Use / to select, then press ENTER.
46
En
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Select and set Start.
4
Select and set Options Update Disc or USB
07
Press ENTER.
Storage Start.
Use / to select, then press ENTER.
6
Downloading of the software start.
The software download status is displayed on the screen.
5
Select and set Yes.
Use /// to select Yes, then press ENTER.
• Depending on the Internet connection conditions,
software downloading may take a certain period of
time.
6
7
Updating starts.
• Software updating may take a certain period of time.
7
8
Updating starts.
• Software updating may take a certain period of time.
Updating completes.
Restoring all the settings to
the factory default settings
Updating completes.
This unit automatically restarts.
Updating using a USB memory
device/disc
1
Check that the player’s power is turned on.
2
When playback is stopped, display the Home
Menu screen.
Press HOME MENU.
Select and set Initial Setup.
Note
• When an update file is provided on the Pioneer
website, use your computer to download it onto a
USB memory device or disc. Carefully read the
instructions on downloading update files provided on
the Pioneer website.
3
Use / to select, then press ENTER.
4
Select and set Options Load Default Next
Screen.
• Store the update file in the root directory of the USB
memory device or disc. Do not store it within a folder.
Use / to select, then press ENTER.
5
Select and set OK.
Use / to select, then press ENTER.
• Do not put any files other than the update file on the
USB memory device or disc.
• To update using a disc, use a CD-R or CD-RW disc.
Note
• The player supports USB memory devices formatted
in FAT32/16. When formatting a USB memory device
on your computer, do so with the settings below.
• After restoring all the settings to the factory default
settings, use Setup Navigator to reset the player
(page 23).
– File system: FAT32
• When all the settings are restored to the factory
defaults, all the data for the secondary video (Picture-
in-Picture), secondary audio, bookmarks, etc., is
erased.
– Allocation unit size: Default allocation size
• Only store the most recent update file on the USB
memory device or disc.
• Do not use a USB extension cable to connect a USB
memory device to the player. Using a USB extension
cable may prevent the player from performing
correctly.
• Steps 1 to 5 are the operations performed by the user.
• Steps 6 to 7 are the operations performed
(automatically) by the player (they are intended to
update the software).
1
Plug in the USB memory device or load the disc on
which the update file is stored.
2
When playback is stopped, display the Home
Menu screen.
Press HOME MENU.
Select and set Initial Setup.
3
Use / to select, then press ENTER.
47
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Language Code Table and Country/Area Code Table
07
Language Code Table
Language name, language code, input code
Abkhazian, ab/abk, 0102
Afar, aa/aar, 0101
Afrikaans, af/afr, 0106
Albanian, sq/sqi, 1917
Amharic, am/amh, 0113
Arabic, ar/ara, 0118
Armenian, hy/hye, 0825
Assamese, as/asm, 0119
Aymara, ay/aym, 0125
Azerbaijani, az/aze, 0126
Bashkir, ba/bak, 0201
Basque, eu/eus, 0521
Belarusian, be/bel, 0205
Bengali, bn/ben, 0214
Bihari, bh/bih, 0208
French, fr/fra, 0618
Malagasy, mg/mlg, 1307
Malay, ms/msa, 1319
Malayalam, ml/mal, 1312
Maltese, mt/mlt, 1320
Maori, mi/mri, 1309
Marathi, mr/mar, 1318
Mongolian, mn/mon, 1314
Moldavian, mo/mol, 1315
Nauru, na/nau, 1401
Nepali, ne/nep, 1405
Norwegian, no/nor, 1415
Occitan, oc/oci, 1503
Oriya, or/ori, 1518
Oromo, om/orm, 1513
Panjabi, pa/pan, 1601
Persian, fa/fas, 0601
Polish, pl/pol, 1612
Portuguese, pt/por, 1620
Pushto, ps/pus, 1619
Quechua, qu/que, 1721
Romanian, ro/ron, 1815
Romansch, rm/roh, 1813
Rundi, rn/run, 1814
Slovenian, sl/slv, 1912
Somali, so/som, 1915
Sotho, Southern, st/sot, 1920
Spanish, es/spa, 0519
Sundanese, su/sun, 1921
Swahili, sw/swa, 1923
Swati, ss/ssw, 1919
Galician, gl/glg, 0712
Georgian, ka/kat, 1101
German, de/deu, 0405
Greek, el/ell, 0512
Guarani, gn/grn, 0714
Gujarati, gu/guj, 0721
Hausa, ha/hau, 0801
Hebrew, iw/heb, 0923
Hindi, hi/hin, 0809
Swedish, sv/swe, 1922
Tagalog, tl/tgl, 2012
Tajik, tg/tgk, 2007
Hungarian, hu/hun, 0821
Icelandic, is/isl, 0919
Indonesian, in/ind, 0914
Interlingua, ia/ina, 0901
Interlingue, ie/ile, 0905
Inupiaq, ik/ipk, 0911
Irish, ga/gle, 0701
Tamil, ta/tam, 2001
Tatar, tt/tat, 2020
Telugu, te/tel, 2005
Thai, th/tha, 2008
Tibetan, bo/bod, 0215
Tigrinya, ti/tir, 2009
Bislama, bi/bis, 0209
Breton, br/bre, 0218
Bulgarian, bg/bul, 0207
Burmese, my/mya, 1325
Catalan, ca/cat, 0301
Central Khmer, km/khm, 1113
Chinese, zh/zho, 2608
Corsican, co/cos, 0315
Croatian, hr/hrv, 0818
Czech, cs/ces, 0319
Tonga (Tonga Islands), to/ton, 2015
Tsonga, ts/tso, 2019
Tswana, tn/tsn, 2014
Turkmen, tk/tuk, 2011
Turkish, tr/tur, 2018
Twi, tw/twi, 2023
Italian, it/ita, 0920
Japanese, ja/jpn, 1001
Javanese, jw/jav, 1023
Kalaallisut, kl/kal, 1112
Kannada, kn/kan, 1114
Kashmiri, ks/kas, 1119
Kazakh, kk/kaz, 1111
Kinyarwanda, rw/kin, 1823
Kirghiz, ky/kir, 1125
Korean, ko/kor, 1115
Kurdish, ku/kur, 1121
Lao, lo/lao, 1215
Ukrainian, uk/ukr, 2111
Urdu, ur/urd, 2118
Russian, ru/rus, 1821
Samoan, sm/smo, 1913
Sango, sg/sag, 1907
Sanskrit, sa/san, 1901
Scottish Gaelic, gd/gla, 0704
Serbian, sr/srp, 1918
Serbo-Croatian, sh/---, 1908
Shona, sn/sna, 1914
Uzbek, uz/uzb, 2126
Vietnamese, vi/vie, 2209
Volapük, vo/vol, 2215
Welsh, cy/cym, 0325
Western Frisian, fy/fry, 0625
Wolof, wo/wol, 2315
Xhosa, xh/xho, 2408
Yiddish, ji/yid, 1009
Yoruba, yo/yor, 2515
Zulu, zu/zul, 2621
Danish, da/dan, 0401
Dutch, nl/nld, 1412
Dzongkha, dz/dzo, 0426
English, en/eng, 0514
Esperanto, eo/epo, 0515
Estonian, et/est, 0520
Finnish, fi/fin, 0609
Latin, la/lat, 1201
Latvian, lv/lav, 1222
Lingala, ln/lin, 1214
Lithuanian, lt/lit, 1220
Macedonian, mk/mkd, 1311
Sindhi, sd/snd, 1904
Sinhalese, si/sin, 1909
Slovak, sk/slk, 1911
Fijian, fj/fij, 0610
Faroese, fo/fao, 0615
Country/Area Code Table
Country/Area name, Country/Area code, input code
Anguilla, ai, 0109
Estonia, ee, 0505
Finland, fi, 0609
France, fr, 0618
Georgia, ge, 0705
Germany, de, 0405
Greece, gr, 0718
Greenland, gl, 0712
Grenada, gd, 0704
Guyana, gy, 0725
Haiti, ht, 0820
Luxembourg, lu, 1221
Slovakia, sk, 1911
Antigua and Barbuda, ag, 0107
Argentina, ar, 0118
Armenia, am, 0113
Australia, au, 0121
Austria, at, 0120
Macedonia, the Former Yugoslav Slovenia, si, 1909
Republic of, mk, 1311
Malaysia, my, 1325
Malta, mt, 1320
Mexico, mx, 1324
Moldova, Republic of, md, 1304
Monaco, mc, 1303
Spain, es, 0519
Suriname, sr, 1918
Sweden, se, 1905
Switzerland, ch, 0308
Taiwan, Province of China, tw, 2023
Tajikistan, tj, 2010
Azerbaijan, az, 0126
Bahamas, bs, 0219
Barbados, bb, 0202
Belarus, by, 0225
Montserrat, ms, 1319
Netherlands, nl, 1412
New Zealand, nz, 1426
Norway, no, 1415
Thailand, th, 2008
Trinidad and Tobago, tt, 2020
Tunisia, tn, 2014
Belgium, be, 0205
Belize, bz, 0226
Hong Kong, hk, 0811
Hungary, hu, 0821
Iceland, is, 0919
India, in, 0914
Turkey, tr, 2018
Bermuda, bm, 0213
Brazil, br, 0218
Pakistan, pk, 1611
Peru, pe, 1605
Turkmenistan, tm, 2013
Turks and Caicos Islands, tc, 2003
Ukraine, ua, 2101
Bulgaria, bg, 0207
Canada, ca, 0301
Indonesia, id, 0904
Ireland, ie, 0905
Philippines, ph, 1608
Poland, pl, 1612
United Kingdom, gb, 0702
United States, us, 2119
Uruguay, uy, 2125
Uzbekistan, uz, 2126
Venezuela, ve, 2205
Virgin Islands, British, vg, 2207
Cayman Islands, ky, 1125
Chile, cl, 0312
Israel, il, 0912
Italy, it, 0920
Portugal, pt, 1620
Puerto Rico, pr, 1618
Romania, ro, 1815
China, cn, 0314
Jamaica, jm, 1013
Japan, jp, 1016
Colombia, co, 0315
Croatia, hr, 0818
Russian Federation, ru, 1821
Saint Kitts and Nevis, kn, 1114
Saint Lucia, lc, 1203
Saint Vincent and the
Grenadines, vc, 2203
San Marino, sm, 1913
Singapore, sg, 1907
Kazakhstan, kz, 1126
Korea, Republic of, kr, 1118
Kyrgyzstan, kg, 1107
Latvia, lv, 1222
Cyprus, cy, 0325
Czech Republic, cz, 0326
Denmark, dk, 0411
Dominica, dm, 0413
Dominican Republic, do, 0415
Liechtenstein, li, 1209
Lithuania, lt, 1220
48
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 8
08
Additional information
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
The implementation was written so as to conform with
Netscapes SSL.
Software
INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR
This library is free for commercial and non-commercial use
as long as the following conditions are aheared to. The
following conditions apply to all code found in this
distribution, be it the RC4, RSA, lhash, DES, etc., code; not
just the SSL code. The SSL documentation included with
this distribution is covered by the same copyright terms
except that the holder is Tim Hudson ([email protected]).
Copyright remains Eric Young's, and as such any Copyright
notices in the code are not to be removed. If this package is
used in a product, Eric Young should be given attribution as
the author of the parts of the library used. This can be in the
form of a textual message at program startup or in
documentation (online or textual) provided with the
package.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the
copyright notice, this list of conditions and the following
disclaimer.
PURPOSE AND NONINFRINGEMENT OF THIRD PARTY
RIGHTS. IN NO EVENT SHALL THE COPYRIGHT HOLDER
OR HOLDERS INCLUDED IN THIS NOTICE BE LIABLE FOR
license Notice
The licenses for the open source
software used on this player are
shown below. For accuracy purposes,
here we have included the original
texts (in English).
ANY CLAIM, OR ANY SPECIAL INDIRECT OR
CONSEQUENTIAL DAMAGES, OR ANY DAMAGES
WHATSOEVER RESULTING FROM LOSS OF USE, DATA
OR PROFITS, WHETHER IN AN ACTION OF CONTRACT,
NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING
OUT OF OR IN CONNECTION WITH THE USE OR
PERFORMANCE OF THIS SOFTWARE.
Except as contained in this notice, the name of a copyright
holder shall not be used in advertising or otherwise to
promote the sale, use or other dealings in this Software
without prior written authorization of the copyright holder.
curl
COPYRIGHT AND PERMISSION NOTICE
Copyright © 1996 - 2007, Daniel Stenberg,
<[email protected]>. All rights reserved.
jpeg
Permission to use, copy, modify, and distribute this
software for any purpose with or without fee is hereby
granted, provided that the above copyright notice and this
permission notice appear in all copies.
This software is based in part on the work of the
independent JPEG Group.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other
materials provided with the distribution.
3. All advertising materials mentioning features or use of
this software must display the following
openssl
The OpenSSL toolkit stays under a dual license, i.e. both the
conditions of the OpenSSL License and the original SSLeay
license apply to the toolkit.
See below for the actual license texts. Actually both
licenses are BSD-style Open Source licenses. In case of any
license issues related to OpenSSL please contact openssl-
OpenSSL License
Copyright (c) 1998-2008 The OpenSSL Project. All rights
reserved.
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the
following conditions are met:
1. Redistributions of source code must retain the above
copyright notice, this list of conditions and the following
disclaimer.
THE SOF TWARE IS PROVIDED "AS IS" , WI THOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT OF THIRD PARTY
RIGHTS. IN NO EVENT SHALL THE AUTHORS OR
COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
DAMAGES OR OTHER LIABILITY, WHETHER IN AN
ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
SOFTWARE.
acknowledgement:
"This product includes cryptographic software written
by Eric Young ([email protected])" The word
'cryptographic' can be left out if the rouines from the
library being used are not cryptographic related :-).
4. If you include any Windows specific code (or a
derivative thereof) from the apps directory (application
code) you must include an acknowledgement:
"This product includes software written by Tim Hudson
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS''
AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO
EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA,
OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
THE POSSIBILITY OF SUCH DAMAGE.
Except as contained in this notice, the name of a copyright
holder shall not be used in advertising or otherwise to
promote the sale, use or other dealings in this Software
without prior written authorization of the copyright holder.
2. Redistributions in binary form must reproduce the
above copyright notice, this list of conditions and the
following disclaimer in the documentation and/or other
materials provided with the distribution.
3. All advertising materials mentioning features or use of
this software must display the following
expat
Copyright (c) 1998, 1999, 2000 Thai Open Source Software
Center Ltd
Permission is hereby granted, free of charge, to any person
obtaining a copy of this software and associated
documentation files (the "Software"), to deal in the Software
without restriction, including without limitation the rights
to use, copy, modify, merge, publish, distribute, sublicense,
and/or sell copies of the Software, and to permit persons to
whom the Software is furnished to do so, subject to the
following conditions:
The above copyright notice and this permission notice shall
be included in all copies or substantial portions of the
Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT
WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT.
acknowledgment:
"This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit. (http:/
/www.openssl.org/)"
4. The names "OpenSSL Toolkit" and "OpenSSL Project"
must not be used to endorse or promote products
derived from this software without prior written
permission. For written permission, please contact
5. Products derived from this software may not be called
"OpenSSL" nor may "OpenSSL" appear in their names
without prior written permission of the OpenSSL
Project.
6. Redistributions of any form whatsoever must retain the
following acknowledgment:
The licence and distribution terms for any publically
available version or derivative of this code cannot be
changed. i.e. this code cannot simply be copied and put
under another distribution licence [including the GNU
Public Licence.]
IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
OTHER LIABILITY, WHETHER IN AN ACTION OF
CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT
OF OR IN CONNECTION WITH THE SOFTWARE OR THE
USE OR OTHER DEALINGS IN THE SOFTWARE.
zlib
for information.
"This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit (http://
www.openssl.org/)"
GNU General Public License and
GNU Lesser General Public License
This product includes the following software licensed for
use under the terms of GNU General
THIS SOFTWARE IS PROVIDED BY THE OpenSSL
PROJECT ``AS IS'' AND ANY EXPRESSED OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE
DISCLAIMED. IN NO EVENT SHALL THE OpenSSL
PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
freetype
This software is based in part on freetype see http://
Public License v2, GNU Lesser General Public License v2.1.
–
–
linux kernel 2.6. Copyright (C) 1991 Linus Torvalds.
Licensed under GPLv2.0
BusyBox v1.17.1 multi-call binary. Copyright (C) 1998-
2009 Erik Andersen, Rob Landley, Denys Vlasenko and
others. Licensed under GPLv2.0
International Components for
Unicode
ICU License - ICU 1.8.1 and later
COPYRIGHT AND PERMISSION NOTICE
Copyright (c) 1995-2010 International Business Machines
Corporation and others
All rights reserved.
Permission is hereby granted, free of charge, to any person
obtaining a copy of this software and associated
documentation files (the "Software"), to deal in the Software
without restriction, including without limitation the rights
to use, copy, modify, merge, publish, distribute, and/or sell
copies of the Software, and to permit persons to whom the
Software is furnished to do so, provided that the above
copyright notice(s) and this permission notice appear in all
copies of the Software and that both the above copyright
notice(s) and this permission notice appear in supporting
documentation.
–
–
SquashFS Copyright: (C) 2002-2009 Phillip Lougher
Licensed under GPL v2.0
Das U-Boot Copyright: (C) 2000-2005 Wolfang Denk,
DENX Software Engineering, [email protected]. Licensed
under GPL v2.0
–
LIRC 0.8.5 Copyright (C) 1996 Ralph Metzler
Christoph Bartelmus <[email protected]> Licensed
under GPL v2.0
This product includes cryptographic software written by
software written by Tim Hudson ([email protected]).
Original SSLeay License
Copyright (C) 1995-1998 Eric Young ([email protected])
All rights reserved.
–
glibc 2.9 Copyright (C) 1992-2006, 2007 Free Software
Foundation, Inc. Licensed under LGPL v2.1.
You can get corresponding open source code from the
following URL.
This package is an SSL implementation written by Eric
Young ([email protected]).
49
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Please refer to the following URL for further information of
GNU General Public License Version 2.
Please refer to the following URL for further information of
GNU Library General Public License Version 2.1.
2. You may modify your copy or copies of the Program or
any portion of it, thus forming a work based on the
Program, and copy and distribute such modifications or
work under the terms of Section 1 above, provided that
you also meet all of these conditions:
a) You must cause the modified files to carry prominent
notices stating that you changed the files and the
date of any change.
b) You must cause any work that you distribute or
publish, that in whole or in part contains or is derived
from the Program or any part thereof, to be licensed
as a whole at no charge to all third parties under the
terms of this License.
c) If the modified program normally reads commands
interactively when run, you must cause it, when
started running for such interactive use in the most
ordinary way, to print or display an announcement
including an appropriate copyright notice and a
notice that there is no warranty (or else, saying that
you provide a warranty) and that users may
5. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Program or its
derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying
or distributing the Program (or any work based on the
Program), you indicate your acceptance of this License
to do so, and all its terms and conditions for copying,
distributing or modifying the Program or works based
on it.
08
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.,
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim
copies of this license document, but changing it is not
allowed.
6
Each time you redistribute the Program (or any work
based on the Program), the recipient automatically
receives a license from the original licensor to copy,
distribute or modify the Program subject to these terms
and conditions. You may not impose any further
restrictions on the recipients' exercise of the rights
granted herein. You are not responsible for enforcing
compliance by third parties to this License.
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the GNU
General Public License is intended to guarantee your
freedom to share and change free software--to make sure
the software is free for all its users. This General Public
License applies to most of the Free Software Foundation's
software and to any other program whose authors commit
to using it. (Some other Free Software Foundation software
is covered by the GNU Lesser General Public License
instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to
freedom, not price. Our General Public Licenses are
designed to make sure that you have the freedom to
distribute copies of free software (and charge for this
service if you wish), that you receive source code or can get
it if you want it, that you can change the software or use
pieces of it in new free programs; and that you know you
can do these things.
To protect your rights, we need to make restrictions that
forbid anyone to deny you these rights or to ask you to
surrender the rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the
software, or if you modify it.
For example, if you distribute copies of such a program,
whether gratis or for a fee, you must give the recipients all
the rights that you have. You must make sure that they, too,
receive or can get the source code. And you must show
them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the
software, and (2) offer you this license which gives you legal
permission to copy, distribute and/or modify the software.
Also, for each author's protection and ours, we want to
make certain that everyone understands that there is no
warranty for this free software. If the software is modified
by someone else and passed on, we want its recipients to
know that what they have is not the original, so that any
problems introduced by others will not reflect on the
original authors' reputations.
Finally, any free program is threatened constantly by
software patents. We wish to avoid the danger that
redistributors of a free program will individually obtain
patent licenses, in effect making the program proprietary.
To prevent this, we have made it clear that any patent must
be licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution
and modification follow.
7. If, as a consequence of a court judgment or allegation
of patent infringement or for any other reason (not
limited to patent issues), conditions are imposed on you
(whether by court order, agreement or otherwise) that
contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you
cannot distribute so as to satisfy simultaneously your
obligations under this License and any other pertinent
obligations, then as a consequence you may not
distribute the Program at all. For example, if a patent
license would not permit royalty-free redistribution of
the Program by all those who receive copies directly or
indirectly through you, then the only way you could
satisfy both it and this License would be to refrain
entirely from distribution of the Program.
If any portion of this section is held invalid or
unenforceable under any particular circumstance, the
balance of the section is intended to apply and the
section as a whole is intended to apply in other
circumstances.
It is not the purpose of this section to induce you to
infringe any patents or other property right claims or to
contest validity of any such claims; this section has the
sole purpose of protecting the integrity of the free
software distribution system, which is implemented by
public license practices. Many people have made
generous contributions to the wide range of software
distributed through that system in reliance on
consistent application of that system; it is up to the
author/donor to decide if he or she is willing to
distribute software through any other system and a
licensee cannot impose that choice.
redistribute the program under these conditions, and
telling the user how to view a copy of this License.
(Exception: if the Program itself is interactive but
does not normally print such an announcement, your
work based on the Program is not required to print an
announcement.)
These requirements apply to the modified work as a whole.
If identifiable sections of that work are not derived from the
Program, and can be reasonably considered independent
and separate works in themselves, then this License, and
its terms, do not apply to those sections when you
distribute them as separate works. But when you distribute
the same sections as part of a whole which is a work based
on the Program, the distribution of the whole must be on
the terms of this License, whose permissions for other
licensees extend to the entire whole, and thus to each and
every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or
contest your rights to work written entirely by you; rather,
the intent is to exercise the right to control the distribution
of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on
the Program with the Program (or with a work based on the
Program) on a volume of a storage or distribution medium
does not bring the other work under the scope of this
License.
3. You may copy and distribute the Program (or a work
based on it, under Section 2) in object code or
executable form under the terms of Sections 1 and 2
above provided that you also do one of the following:
a) Accompany it with the complete corresponding
machine-readable source code, which must be
distributed under the terms of Sections 1 and 2 above
on a medium customarily used for software
This section is intended to make thoroughly clear what
is believed to be a consequence of the rest of this
License.
8. If the distribution and/or use of the Program is
restricted in certain countries either by patents or by
copyrighted interfaces, the original copyright holder
who places the Program under this License may add an
explicit geographical distribution limitation excluding
those countries, so that distribution is permitted only in
or among countries not thus excluded. In such case,
this License incorporates the limitation as if written in
the body of this License.
9. The Free Software Foundation may publish revised and/
or new versions of the General Public License from time
to time. Such new versions will be similar in spirit to the
present version, but may differ in detail to address new
problems or concerns.
Each version is given a distinguishing version number.
If the Program specifies a version number of this
License which applies to it and "any later version", you
have the option of following the terms and conditions
either of that version or of any later version published by
the Free Software Foundation. If the Program does not
specify a version number of this License, you may
choose any version ever published by the Free Software
Foundation.
10. If you wish to incorporate parts of the Program into
other free programs whose distribution conditions are
different, write to the author to ask for permission. For
software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we
sometimes make exceptions for this. Our decision will
be guided by the two goals of preserving the free status
of all derivatives of our free software and of promoting
the sharing and reuse of software generally.
interchange; or,
b) Accompany it with a written offer, valid for at least
three years, to give any third party, for a charge no
more than your cost of physically performing source
distribution, a complete machine-readable copy of
the corresponding source code, to be distributed
under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange;
or,
c) Accompany it with the information you received as to
the offer to distribute corresponding source code.
(This alternative is allowed only for noncommercial
distribution and only if you received the program in
object code or executable form with such an offer, in
accord with Subsection b above.)
The source code for a work means the preferred form of the
work for making modifications to it. For an executable
work, complete source code means all the source code for
all modules it contains, plus any associated interface
definition files, plus the scripts used to control compilation
and installation of the executable. However, as a special
exception, the source code distributed need not include
anything that is normally distributed (in either source or
binary form) with the major components (compiler, kernel,
and so on) of the operating system on which the executable
runs, unless that component itself accompanies the
executable.
If distribution of executable or object code is made by
offering access to copy from a designated place, then
offering equivalent access to copy the source code from the
same place counts as distribution of the source code, even
though third parties are not compelled to copy the source
along with the object code.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION
AND MODIFICATION
0. This License applies to any program or other work
which contains a notice placed by the copyright holder
saying it may be distributed under the terms of this
General Public License. The "Program", below, refers to
any such program or work, and a "work based on the
Program" means either the Program or any derivative
work under copyright law: that is to say, a work
containing the Program or a portion of it, either
verbatim or with modifications and/or translated into
another language. (Hereinafter, translation is included
without limitation in the term "modification".) Each
licensee is addressed as "you".
Activities other than copying, distribution and
modification are not covered by this License; they are
outside its scope. The act of running the Program is not
restricted, and the output from the Program is covered
only if its contents constitute a work based on the
Program (independent of having been made by running
the Program). Whether that is true depends on what the
Program does.
1. You may copy and distribute verbatim copies of the
Program's source code as you receive it, in any
medium, provided that you conspicuously and
appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact
all the notices that refer to this License and to the
absence of any warranty; and give any other recipients
of the Program a copy of this License along with the
Program.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF
CHARGE, THERE IS NO WARRANTY FOR THE
PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE
STATED IN WRITING THE COPYRIGHT HOLDERS AND/
OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS"
WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
4. You may not copy, modify, sublicense, or distribute the
Program except as expressly provided under this
License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will
automatically terminate your rights under this License.
However, parties who have received copies, or rights,
from you under this License will not have their licenses
terminated so long as such parties remain in full
compliance.
You may charge a fee for the physical act of transferring
a copy, and you may at your option offer warranty
protection in exchange for a fee.
50
En
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE
QUALITY AND PERFORMANCE OF THE PROGRAM IS
WITH YOU. SHOULD THE PROGRAM PROVE
DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE
PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS
OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES
OR A FAILURE OF THE PROGRAM TO OPERATE WITH
ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR
OTHER PARTY HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
freedom to share and change free software--to make sure
the software is free for all its users.
derived from the library, whereas the latter must be
combined with the library in order to run.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION
08
This license, the Lesser General Public License, applies to
some specially designated software packages--typically
libraries--of the Free Software Foundation and other
authors who decide to use it. You can use it too, but we
suggest you first think carefully about whether this license
or the ordinary General Public License is the better strategy
to use in any particular case, based on the explanations
below.
When we speak of free software, we are referring to
freedom of use, not price. Our General Public Licenses are
designed to make sure that you have the freedom to
distribute copies of free software (and charge for this
service if you wish); that you receive source code or can get
it if you want it; that you can change the software and use
pieces of it in new free programs; and that you are informed
that you can do these things.
To protect your rights, we need to make restrictions that
forbid distributors to deny you these rights or to ask you to
surrender these rights. These restrictions translate to
certain responsibilities for you if you distribute copies of the
library or if you modify it.
For example, if you distribute copies of the library, whether
gratis or for a fee, you must give the recipients all the rights
that we gave you. You must make sure that they, too,
receive or can get the source code. If you link other code
with the library, you must provide complete object files to
the recipients, so that they can relink them with the library
after making changes to the library and recompiling it. And
you must show them these terms so they know their rights.
We protect your rights with a two-step method: (1) we
copyright the library, and (2) we offer you this license,
which gives you legal permission to copy, distribute and/or
modify the library.
To protect each distributor, we want to make it very clear
that there is no warranty for the free library. Also, if the
library is modified by someone else and passed on, the
recipients should know that what they have is not the
original version, so that the original author's reputation will
not be affected by problems that might be introduced by
others.
Finally, software patents pose a constant threat to the
existence of any free program. We wish to make sure that
a company cannot effectively restrict the users of a free
program by obtaining a restrictive license from a patent
holder. Therefore, we insist that any patent license
obtained for a version of the library must be consistent with
the full freedom of use specified in this license.
Most GNU software, including some libraries, is covered by
the ordinary GNU General Public License. This license, the
GNU Lesser General Public License, applies to certain
designated libraries, and is quite different from the ordinary
General Public License. We use this license for certain
libraries in order to permit linking those libraries into non-
free programs.
When a program is linked with a library, whether statically
or using a shared library, the combination of the two is
legally speaking a combined work, a derivative of the
original library. The ordinary General Public License
therefore permits such linking only if the entire
AND MODIFICATION
0. This License Agreement applies to any software library
or other program which contains a notice placed by the
copyright holder or other authorized party saying it may
be distributed under the terms of this Lesser General
Public License (also called "this License"). Each
licensee is addressed as "you".
A "library" means a collection of software functions and/
or data prepared so as to be conveniently linked with
application programs (which use some of those
functions and data) to form executables.
The "Library", below, refers to any such software library
or work which has been distributed under these terms.
A "work based on the Library" means either the Library
or any derivative work under copyright law: that is to say,
a work containing the Library or a portion of it, either
verbatim or with modifications and/or translated
straightforwardly into another language. (Hereinafter,
translation is included without limitation in the term
"modification".)
"Source code" for a work means the preferred form of
the work for making modifications to it. For a library,
complete source code means all the source code for all
modules it contains, plus any associated interface
definition files, plus the scripts used to control
compilation and installation of the library.
Activities other than copying, distribution and
modification are not covered by this License; they are
outside its scope. The act of running a program using
the Library is not restricted, and output from such a
program is covered only if its contents constitute a work
based on the Library (independent of the use of the
Library in a tool for writing it). Whether that is true
depends on what the Library does and what the
program that uses the Library does.
1. You may copy and distribute verbatim copies of the
Library's complete source code as you receive it, in any
medium, provided that you conspicuously and
appropriately publish on each copy an appropriate
copyright notice and disclaimer of warranty; keep intact
all the notices that refer to this License and to the
absence of any warranty; and distribute a copy of this
License along with the Library.
You may charge a fee for the physical act of transferring
a copy, and you may at your option offer warranty
protection in exchange for a fee.
2. You may modify your copy or copies of the Library or any
portion of it, thus forming a work based on the Library,
and copy and distribute such modifications or work
under the terms of Section 1 above, provided that you
also meet all of these conditions:
a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent
notices stating that you changed the files and the
date of any change.
c) You must cause the whole of the work to be licensed
at no charge to all third parties under the terms of
this License.
d) If a facility in the modified Library refers to a function
or a table of data to be supplied by an application
program that uses the facility, other than as an
argument passed when the facility is invoked, then
you must make a good faith effort to ensure that, in
the event an application does not supply such
function or table, the facility still operates, and
performs whatever part of its purpose remains
meaningful.
(For example, a function in a library to compute
square roots has a purpose that is entirely well-
defined independent of the application. Therefore,
Subsection 2d requires that any application-supplied
function or table used by this function must be
optional: if the application does not supply it, the
square root function must still compute square
roots.)
These requirements apply to the modified work as a
whole. If identifiable sections of that work are not
derived from the Library, and can be reasonably
considered independent and separate works in
themselves, then this License, and its terms, do not
apply to those sections when you distribute them as
separate works. But when you distribute the same
sections as part of a whole which is a work based on the
Library, the distribution of the whole must be on the
terms of this License, whose permissions for other
licensees extend to the entire whole, and thus to each
and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or
contest your rights to work written entirely by you;
rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on
the Library.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the
greatest possible use to the public, the best way to achieve
this is to make it free software which everyone can
redistribute and change under these terms.
To do so, attach the following notices to the program. It is
safest to attach them to the start of each source file to most
effectively convey the exclusion of warranty; and each file
should have at least the "copyright" line and a pointer to
where the full notice is found.
<one line to give the program's name and a brief idea
of what it does.>
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it
and/or modify it under the terms of the GNU General
Public License as published by the Free Software
Foundation; either version 2 of the License, or (at your
option) any later version.
This program is distributed in the hope that it will be
useful, but WITHOUT ANY WARRANTY; without even
the implied warranty of MERCHANTABILITY or FITNESS
FOR A PARTICULAR PURPOSE. See the GNU General
Public License for more details.
You should have received a copy of the GNU General
Public License along with this program; if not, write to
the Free Software Foundation, Inc., 51 Franklin Street,
Fifth Floor, Boston, MA 02110-1301 USA.
Also add information on how to contact you by electronic
and paper mail.
If the program is interactive, make it output a short notice
like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of
author
Gnomovision comes with ABSOLUTELY NO
WARRANTY; for details type `show w'.
This is free software, and you are welcome to
redistribute it under certain conditions; type `show c'
for details.
The hypothetical commands `show w' and `show c' should
show the appropriate parts of the General Public License.
Of course, the commands you use may be called
something other than `show w' and `show c'; they could
even be mouse-clicks or menu items--whatever suits your
program.
You should also get your employer (if you work as a
programmer) or your school, if any, to sign a "copyright
disclaimer" for the program, if necessary. Here is a sample;
alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in
the program
combination fits its criteria of freedom. The Lesser General
Public License permits more lax criteria for linking other
code with the library.
We call this license the "Lesser" General Public License
because it does Less to protect the user's freedom than the
ordinary General Public License. It also provides other free
software developers Less of an advantage over competing
non-free programs. These disadvantages are the reason we
use the ordinary General Public License for many libraries.
However, the Lesser license provides advantages in certain
special circumstances.
For example, on rare occasions, there may be a special
need to encourage the widest possible use of a certain
library, so that it becomes a de-facto standard. To achieve
this, non-free programs must be allowed to use the library.
A more frequent case is that a free library does the same
job as widely used non-free libraries. In this case, there is
little to gain by limiting the free library to free software only,
so we use the Lesser General Public License.
In other cases, permission to use a particular library in non-
free programs enables a greater number of people to use a
large body of free software. For example, permission to use
the GNU C Library in non-free programs enables many
more people to use the whole GNU operating system, as
well as its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less
protective of the users' freedom, it does ensure that the
user of a program that is linked with the Library has the
freedom and the wherewithal to run that program using a
modified version of the Library.
`Gnomovision' (which makes passes at compilers)
written by James Hacker.
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating
your program into proprietary programs. If your program is
a subroutine library, you may consider it more useful to
permit linking proprietary applications with the library. If
this is what you want to do, use the GNU Lesser General
Public License instead of this License.
GNU LESSER GENERAL PUBLICLICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim
copies of this license document, but changing it is not
allowed.
[This is the first released version of the Lesser GPL. It also
counts as the successor of the GNU Library Public License,
version 2, hence the version number 2.1.]
The precise terms and conditions for copying, distribution
and modification follow. Pay close attention to the
difference between a "work based on the library" and a
"work that uses the library". The former contains code
Preamble
The licenses for most software are designed to take away
your freedom to share and change it. By contrast, the GNU
General Public Licenses are intended to guarantee your
51
En
Download from Www.Somanuals.com. All Manuals Search And Download.
In addition, mere aggregation of another work not
based on the Library with the Library (or with a work
based on the Library) on a volume of a storage or
distribution medium does not bring the other work
under the scope of this License.
b) Use a suitable shared library mechanism for linking
with the Library. A suitable mechanism is one that (1)
uses at run time a copy of the library already present
on the user's computer system, rather than copying
library functions into the executable, and (2) will
operate properly with a modified version of the library,
if the user installs one, as long as the modified
version is interface-compatible with the version that
the work was made with.
c) Accompany the work with a written offer, valid for at
least three years, to give the same user the materials
specified in Subsection 6a, above, for a charge no
more than the cost of performing this distribution.
d) If distribution of the work is made by offering access
to copy from a designated place, offer equivalent
access to copy the above specified materials from the
same place.
It is not the purpose of this section to induce you to
infringe any patents or other property right claims or to
contest validity of any such claims; this section has the
sole purpose of protecting the integrity of the free
software distribution system which is implemented by
public license practices. Many people have made
generous contributions to the wide range of software
distributed through that system in reliance on
consistent application of that system; it is up to the
author/donor to decide if he or she is willing to
distribute software through any other system and a
licensee cannot impose that choice.
08
3. You may opt to apply the terms of the ordinary GNU
General Public License instead of this License to a given
copy of the Library. To do this, you must alter all the
notices that refer to this License, so that they refer to the
ordinary GNU General Public License, version 2, instead
of to this License. (If a newer version than version 2 of
the ordinary GNU General Public License has appeared,
then you can specify that version instead if you wish.)
Do not make any other change in these notices.
Once this change is made in a given copy, it is
irreversible for that copy, so the ordinary GNU General
Public License applies to all subsequent copies and
derivative works made from that copy.
This option is useful when you wish to copy part of the
code of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion or
derivative of it, under Section 2) in object code or
executable form under the terms of Sections 1 and 2
above provided that you accompany it with the
complete corresponding machine-readable source
code, which must be distributed under the terms of
Sections 1 and 2 above on a medium customarily used
for software interchange.
If distribution of object code is made by offering access
to copy from a designated place, then offering
equivalent access to copy the source code from the
same place satisfies the requirement to distribute the
source code, even though third parties are not
compelled to copy the source along with the object
code.
5. A program that contains no derivative of any portion of
the Library, but is designed to work with the Library by
being compiled or linked with it, is called a "work that
uses the Library". Such a work, in isolation, is not a
derivative work of the Library, and therefore falls outside
the scope of this License.
However, linking a "work that uses the Library" with the
Library creates an executable that is a derivative of the
Library (because it contains portions of the Library),
rather than a "work that uses the library". The
executable is therefore covered by this License. Section
6 states terms for distribution of such executables.
When a "work that uses the Library" uses material from
a header file that is part of the Library, the object code
for the work may be a derivative work of the Library even
though the source code is not. Whether this is true is
especially significant if the work can be linked without
the Library, or if the work is itself a library. The threshold
for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters,
data structure layouts and accessors, and small
macros and small inline functions (ten lines or less in
length), then the use of the object file is unrestricted,
regardless of whether it is legally a derivative work.
(Executables containing this object code plus portions
of the Library will still fall under Section 6.)
This section is intended to make thoroughly clear what
is believed to be a consequence of the rest of this
License.
12. If the distribution and/or use of the Library is restricted
in certain countries either by patents or by copyrighted
interfaces, the original copyright holder who places the
Library under this License may add an explicit
geographical distribution limitation excluding those
countries, so that distribution is permitted only in or
among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the
body of this License.
13. The Free Software Foundation may publish revised and/
or new versions of the Lesser General Public License
from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to
address new problems or concerns.
Each version is given a distinguishing version number.
If the Library specifies a version number of this License
which applies to it and "any later version", you have the
option of following the terms and conditions either of
that version or of any later version published by the Free
Software Foundation. If the Library does not specify a
license version number, you may choose any version
ever published by the Free Software Foundation.
14. If you wish to incorporate parts of the Library into other
free programs whose distribution conditions are
incompatible with these, write to the author to ask for
permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software
Foundation; we sometimes make exceptions for this.
Our decision will be guided by the two goals of
preserving the free status of all derivatives of our free
software and of promoting the sharing and reuse of
software generally.
e) Verify that the user has already received a copy of
these materials or that you have already sent this
user a copy.
For an executable, the required form of the "work that
uses the Library" must include any data and utility
programs needed for reproducing the executable from
it. However, as a special exception, the materials to be
distributed need not include anything that is normally
distributed (in either source or binary form) with the
major components (compiler, kernel, and so on) of the
operating system on which the executable runs, unless
that component itself accompanies the executable.
It may happen that this requirement contradicts the
license restrictions of other proprietary libraries that do
not normally accompany the operating system. Such a
contradiction means you cannot use both them and the
Library together in an executable that you distribute.
7. You may place library facilities that are a work based on
the Library side-by-side in a single library together with
other library facilities not covered by this License, and
distribute such a combined library, provided that the
separate distribution of the work based on the Library
and of the other library facilities is otherwise permitted,
and provided that you do these two things:
a) Accompany the combined library with a copy of the
same work based on the Library, uncombined with
any other library facilities. This must be distributed
under the terms of the Sections above.
b) Give prominent notice with the combined library of
the fact that part of it is a work based on the Library,
and explaining where to find the accompanying
uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or
distribute the Library except as expressly provided
under this License. Any attempt otherwise to copy,
modify, sublicense, link with, or distribute the Library is
void, and will automatically terminate your rights under
this License. However, parties who have received
copies, or rights, from you under this License will not
have their licenses terminated so long as such parties
remain in full compliance.
9. You are not required to accept this License, since you
have not signed it. However, nothing else grants you
permission to modify or distribute the Library or its
derivative works. These actions are prohibited by law if
you do not accept this License. Therefore, by modifying
or distributing the Library (or any work based on the
Library), you indicate your acceptance of this License to
do so, and all its terms and conditions for copying,
distributing or modifying the Library or works based on
it.
10. Each time you redistribute the Library (or any work
based on the Library), the recipient automatically
receives a license from the original licensor to copy,
distribute, link with or modify the Library subject to
these terms and conditions. You may not impose any
further restrictions on the recipients' exercise of the
rights granted herein. You are not responsible for
enforcing compliance by third parties with this License.
11. If, as a consequence of a court judgment or allegation
of patent infringement or for any other reason (not
limited to patent issues), conditions are imposed on you
(whether by court order, agreement or otherwise) that
contradict the conditions of this License, they do not
excuse you from the conditions of this License. If you
cannot distribute so as to satisfy simultaneously your
obligations under this License and any other pertinent
obligations, then as a consequence you may not
distribute the Library at all. For example, if a patent
license would not permit royalty-free redistribution of
the Library by all those who receive copies directly or
indirectly through you, then the only way you could
satisfy both it and this License would be to refrain
entirely from distribution of the Library.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF
CHARGE, THERE IS NO WARRANTY FOR THE
LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE
LAW. EXCEPT WHEN OTHERWISE STATED IN
WRITING THE COPYRIGHT HOLDERS AND/OR OTHER
PARTIES PROVIDE THE LIBRARY "AS IS" WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE
RISK AS TO THE QUALITY AND PERFORMANCE OF
THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY
PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE
LAW OR AGREED TO IN WRITING WILL ANY
COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO
MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY
AS PERMITTED ABOVE, BE LIABLE TO YOU FOR
DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE
LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF
DATA OR DATA BEING RENDERED INACCURATE OR
LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A
FAILURE OF THE LIBRARY TO OPERATE WITH ANY
OTHER SOFTWARE), EVEN IF SUCH HOLDER OR
OTHER PARTY HAS BEEN ADVISED OF THE
Otherwise, if the work is a derivative of the Library, you
may distribute the object code for the work under the
terms of Section 6. Any executables containing that
work also fall under Section 6, whether or not they are
linked directly with the Library itself.
6. As an exception to the Sections above, you may also
combine or link a "work that uses the Library" with the
Library to produce a work containing portions of the
Library, and distribute that work under terms of your
choice, provided that the terms permit modification of
the work for the customer's own use and reverse
engineering for debugging such modifications.
You must give prominent notice with each copy of the
work that the Library is used in it and that the Library
and its use are covered by this License. You must
supply a copy of this License. If the work during
execution displays copyright notices, you must include
the copyright notice for the Library among them, as well
as a reference directing the user to the copy of this
License. Also, you must do one of these things:
a) Accompany the work with the complete
POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the
greatest possible use to the public, we recommend making
it free software that everyone can redistribute and change.
You can do so by permitting redistribution under these
terms (or, alternatively, under the terms of the ordinary
General Public License).
To apply these terms, attach the following notices to the
library. It is safest to attach them to the start of each source
file to most effectively convey the exclusion of warranty; and
each file should have at least the "copyright" line and a
pointer to where the full notice is found.
<one line to give the library's name and a brief idea of
what it does.>
Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/
or modify it under the terms of the GNU Lesser General
Public
corresponding machine-readable source code for the
Library including whatever changes were used in the
work (which must be distributed under Sections 1
and 2 above); and, if the work is an executable linked
with the Library, with the complete machine-readable
"work that uses the Library", as object code and/or
source code, so that the user can modify the Library
and then relink to produce a modified executable
containing the modified Library. (It is understood
that the user who changes the contents of definitions
files in the Library will not necessarily be able to
recompile the application to use the modified
definitions.)
If any portion of this section is held invalid or
unenforceable under any particular circumstance, the
balance of the section is intended to apply, and the
section as a whole is intended to apply in other
circumstances.
52
En
Download from Www.Somanuals.com. All Manuals Search And Download.
License as published by the Free Software Foundation;
either version 2.1 of the License, or (at your option) any
later version.
08
This library is distributed in the hope that it will be
useful, but WITHOUT ANY WARRANTY; without even
the implied warranty of MERCHANTABILITY or FITNESS
FOR A PARTICULAR PURPOSE. See the GNU Lesser
General Public License for more details.
You should have received a copy of the GNU Lesser
General Public License along with this library; if not,
write to the Free Software
Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
MA 02110-1301 USA
Also add information on how to contact you by electronic
and paper mail.
You should also get your employer (if you work as a
programmer) or your school, if any, to sign a "copyright
disclaimer" for the library, if necessary. Here is a sample;
alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in
the library `Frob' (a library for tweaking knobs) written
by James Random Hacker.
<signature of Ty Coon>, 1 April 1990
Ty Coon, President of Vice
That's all there is to it!
53
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Condensation
Cautions on use
08
If the player is moved suddenly from a cold place into a
warm room (in winter, for example) or if the temperature
in the room in which the player is installed rises suddenly
due to a heater, etc., water droplets (condensation) may
form inside (on operating parts and the lens). When
condensation is present, the player will not operate
properly and playback is not possible. Let the player stand
at room temperature for 1 or 2 hours with the power
turned on (the time depends on the extent of
Moving the player
If you need to move this unit, first remove the disc if
there’s one loaded, and close the disc tray. Next, press
STANDBY/ON to switch the power to standby,
checking that the POWER OFF indication on the front
panel display goes off. Wait at least 10 seconds. Lastly,
disconnect the power cord.
condensation). The water droplets will dissipate and
playback will become possible.
Never lift or move the unit during playback — discs rotate
at a high speed and may be damaged.
Condensation can also occur in the summer if the player
is exposed to the direct wind from an air-conditioner. If
this happens, move the player to a different place.
Place of installation
Select a stable place near the TV and AV system to which
the unit is connected.
Cleaning the player
Normally, wipe the player with a soft cloth. For tough dirt,
apply some neutral detergent diluted in 5 to 6 parts water
to a soft cloth, wring out thoroughly, wipe off the dirt, then
wipe again with a dry cloth.
Do not place the player on top of a TV or color monitor.
Keep it away from cassette decks or other components
easily affected by magnetism.
Avoid the following types of places:
• Places exposed to direct sunlight
• Humid or poorly ventilated places
• Extremely hot or cold places
• Places subject to vibration
• Dusty places
Note that getting alcohol, thinner, benzene or insecticide
on the player could cause the print and coating to peel off.
Also, avoid leaving rubber or vinyl products in contact
with the player for long periods of time, as this could
damage the cabinet.
When using chemical-impregnated wipes, etc., read the
wipe’s cautions carefully.
• Places exposed to soot, steam or heat (in kitchens,
etc.)
Unplug the power cord from the power outlet when
cleaning the player.
Do not place objects on top
Do not place objects on top of the player.
Caution for when the unit is
installed in a rack with a glass
door
Do not obstruct the ventilation
holes
Do not use the player on a shaggy rug, bed, or sofa, and
do not cover the player with a cloth, etc. Doing so will
prevent heat dissipation and could lead to damage.
Do not press the OPEN/CLOSE on the remote control
to open the disc tray while the glass door is closed. The
door will hamper the movement of the disc tray, and the
unit could be damaged.
Keep away from heat
Do not place the player on top of an amplifier or other
device generating heat. When installing in a rack, to avoid
the heat generated by the amplifier and other devices,
place it on a shelf below the amplifier whenever possible.
Cleaning the pickup lens
The player’s lens should not become dirty in normal use,
but if for some reason it should malfunction due to dust
or dirt, consult your nearest Pioneer authorized service
center. Although lens cleaners for players are
commercially available, we advise against using them
since some may damage the lens.
Turn the power off when not
using the player
Depending on the conditions of the TV broadcast signals,
striped patterns may appear on the screen when the TV is
turned on while the player’s power is turned on. This is not
a malfunction with the player or TV. If this happens, turn
the player’s power off. In the same way, noise may be
heard in the sound of a radio.
Handling discs
Do not use damaged (cracked or warped) discs.
Do not scratch the disc’s signal surface or let it get dirty.
Do not load more than one disc into the player at a time.
54
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Do not glue paper or put stickers onto the disc, or use a
pencil, ball-point pen or other sharp-tipped writing
instrument. These could all damage the disc.
Do not use benzene, thinner or other volatile chemicals.
Also do not use record spray or antistatic agents.
08
For tough dirt, apply some water to a soft cloth, wring out
thoroughly, wipe off the dirt, then wipe off the moisture
with a dry cloth.
Specially shaped discs
Specially shaped discs (heart-shaped, hexagonal, etc.)
cannot be used on this player. Never use such discs, as
they will damage the player.
Storing discs
Always store discs in their cases, and place the cases
vertically, avoiding places exposed to high temperatures
or humidity, direct sunlight or extremely low
temperatures.
Be sure to read the cautions included with the disc.
Cleaning discs
Condensation on discs
It may not be possible to play the disc if there are
fingerprints or dust on it. In this case, using a cleaning
cloth, etc., to wipe the disc gently from the center toward
the outer edge. Do not use a dirty cleaning cloth.
If the disc is moved suddenly from a cold place into a
warm room (in winter, for example), water droplets
(condensation) may form on the disc surface. Discs will
not play properly if there is condensation on them.
Carefully wipe off the water droplets from the disc surface
before using the disc.
Troubleshooting
Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this
component, check the points below. Sometimes the trouble may lie in another component. Inspect the other
components and electrical appliances being used. If the trouble cannot be rectified even after checking the points
below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
Playback
Problem
Check
Remedy
• Disc does not play.
Is the disc one that is
playable on this player?
Check whether the disc is one that can be played on this player
(page 7).
• Disc tray opens
automatically.
Is the file one that is playable • Check whether the file is one that can be played on this player
on this player?
(page 10).
• Check whether or not the file is damaged.
Is the disc scratched?
Is the disc dirty?
It may not be possible to play scratched discs.
Clean the disc (above).
Is there a piece of paper or
sticker attached to the disc?
The disc may be warped and unplayable.
Is the disc properly set in the • Set the disc with the printed side facing up.
disc tray?
• Set the disc properly in the depression in the disc tray.
Is the region number correct? See page 9 for the region numbers of discs that can be played on this
player.
55
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Check
Remedy
08
No picture is displayed or the Is the video cable properly
picture is not displayed
properly.
• Connect the cable properly according to the connected devices
(page 15).
connected?
• Disconnect the cable (video/audio cable or HDMI cable), then
reinsert it firmly and all the way in.
• For BDP-LX55, a TV or any other device which outputs video signals
must be connected to the HDMI OUT (MAIN) terminal (page 18).
Is the video cable damaged? If the cable is damaged, replace it with a new one.
Is the input setting on the
Read the operating instructions for the connected components and
connected TV or AV receiver switch to the proper input.
or amplifier right?
Is the output video resolution • On the BDP-LX55, switch the resolution at Resolution (page 41).
properly set?
• On the BDP-440/BDP-140, press HDMI to switch the video resolution
output from the HDMI OUT terminal (page 12).
• Is the player connected
with an HDMI cable other
1080p or Deep Color video signals may not be output properly,
depending on the HDMI cable being used or the player’s settings. If you
wish to output the video signals with 1080p or Deep Color, connect the
®
than a High Speed HDMI
cable (with a Standard
®
TV using a High Speed HDMI cable without a built-in equalizer, then
reset the player using the Setup Navigator (page 23).
®
HDMI cable)?
• Are you using an HDMI
cable with a built-in
equalizer?
Is a DVI device connected?
The picture may not be displayed properly if a DVI device is connected.
Is Color Space properly set? Change the Color Space setting (page 41).
For the BDP-LX55:
Is the HDMI Mode set
appropriately?
Set the HDMI Mode to something other than Pure Audio (page 41).
Picture freezes and the front
panel and remote control
buttons stop working.
• Press STOP to stop playback, then restart playback.
• If the playback cannot be stopped, press STANDBY/ON on the
player’s front panel to turn off the power, then turn the power back on.
• If the power cannot be turned off, unplug the power cord, wait several
seconds, then plug the power cord back into the outlet.
No picture is displayed or
picture is not output in high
definition when playing BDs.
With some discs, it may not be possible to output the video signals from
the VIDEO output terminal. In this case, connect using an HDMI cable
(page 15).
• Picture is disturbed during
playback.
• This player supports Rovi analog copy protection technology. With
some TVs (such as with built-in video deck), the picture will not be
displayed properly when the copy protected DVD title is played. This is
not a malfunction.
• Picture is dark.
• If the player and TV are connected via a DVD recorder/video deck,
etc., the picture will not be displayed properly due to analog copy
protection. Connect the player and TV directly.
• Picture is stretched.
• Picture is cropped.
Is the TV’s aspect ratio
properly set?
Read the operating instructions for the TV and set the TV’s aspect ratio
properly.
• Aspect ratio cannot be
switched.
Is TV Screen properly set?
Set TV Screen properly (page 39).
When video signals with a resolution of 1080/50i, 1080/50p, 720/50p,
1080/24p, 1080/60i, 1080/60p or 720/60p are being output from the
HDMI OUT terminal, they may be output with an aspect ratio of 16:9
even if TV Screen is set to 4:3 Pan&Scan (page 39).
Picture is interrupted.
The picture may be interrupted when the resolution of the recorded
video signal switches. On the BDP-LX55, switch the resolution at
Resolution (page 41). On the BDP-440/BDP-140, press HDMI to select
a setting other than Auto (page 41).
The subtitles cannot be
switched.
The subtitles cannot be switched for discs recorded on a DVD or BD
recorder.
56
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Check
Remedy
08
• No sound is output.
• Sound is not output
properly.
Is the disc played back in
slow motion?
Is the disc played back in fast
forward or fast reverse?
No sound is output during slow motion play and forward and reverse
scanning.
Are the audio cables properly • Connect the cable properly according to the connected devices
connected?
(page 15).
• Insert the cable firmly and all the way in.
Is the audio cable damaged? If the cable is damaged, replace it with a new one.
Is Audio Output properly
set?
Set Audio Output properly, according to the connected device
(page 40).
Are the connected
Read the operating instructions for the connected components and
components (AV receiver or check the volume, input, speaker settings, etc.
amplifier, etc.) properly set?
Are you trying to listen to the Audio signals are not output from the HDMI OUT terminal when video
sound of the HDMI OUT
signals are being output from the VIDEO output terminals. When
terminal while watching the watching the picture of the VIDEO output terminals, connect an optical
picture from the VIDEO
output terminals?
digital audio cable or regular audio cables to listen to the sound
(page 20). Once connections are completed, use Setup Navigator to
make the player’s settings (page 23).
Is HDMI Audio Out properly Set HDMI Audio Out to Re-encode or PCM. (page 41).
set?
Is a DVI device connected?
The sound will not be output from the HDMI OUT terminal if a DVI
device is connected. Connect the device to a DIGITAL OUT terminal or
the AUDIO OUT terminals (page 20).
For some BDs, audio signals are only output from DIGITAL OUT
terminal or the HDMI OUT terminal.
For the BDP-LX55:
Is the HDMI Mode set
appropriately?
Set the HDMI Mode properly, according to the connected device
(page 41).
Multi-channel sound is not
output.
Is the audio output of the
connected AV receiver or
amplifier, etc., properly set? amplifier.
Read the operating instructions for the connected AV receiver or
amplifier and check the audio output settings of the AV receiver or
Is multi-channel sound
selected?
Use the menu screen or AUDIO to switch the disc’s sound to multi-
channel.
Noise can be heard when
Is the connected AV receiver If an AV receiver or amplifier that is not compatible with DTS Digital
outputting DTS Digital Audio or amplifier compatible with Surround is connected to the DIGITAL OUT terminal, set Digital
signals from the DIGITAL
DTS Digital Surround?
Output to PCM (page 40).
OUT terminal.
192 kHz or 96 kHz digital
audio signals cannot be
output from the DIGITAL
OUT terminal.
It is not possible to output 192 kHz or 96 kHz digital audio signals from
this player’s DIGITAL OUT terminal. The signals are automatically
converted to 48 kHz or less for output.
Secondary audio or
interactive audio is not
output.
Is HDMI Audio Out properly When listening to the sound from an HDMI OUT terminal, set HDMI
set? Audio Out to PCM (page 41).
Are Digital Output properly When listening to the sound from an DIGITAL OUT terminal, set
set?
Digital Output to Re-encode or PCM (page 40).
Sound is fast or slow.
(Only for BDP-LX55 and BDP-
440)
When an HDMI cable is
When a Pioneer AV receiver or amplifier compatible with the PQLS
connected, are audio signals function is connected directly to the player’s HDMI OUT terminal using
being output from devices
connected with cables other CD (CD-DA). Because of this, the sound output from components other
an HDMI cable, the PQLS function is activated when playing an audio
than HDMI cables?
than the ones connected by an HDMI cable may be fast or slow. If this
happens, set Control to Off (page 41).
After a disc is inserted,
Loading stays displayed and recorded on the disc?
playback does not start.
Are there too many files
When a disc on which files are recorded is inserted, depending on the
number of files recorded on the disc, loading may take several dozen
minutes.
is displayed in file names,
etc.
The characters that cannot be displayed on this player are displayed in
.
A message indicating low
memory appears while
playing a BD-ROM disc.
• Connect a USB memory device (page 21).
• Erase the data stored on the connected USB memory device from
BUDA Setup (page 45).
57
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Control function
08
Problem
Check
Remedy
Control function does not
work.
Is the HDMI cable properly
connected?
To use the Control function, connect the Flat Screen TV and AV system
(AV receiver or amplifier, etc.) to the HDMI OUT terminal (page 15).
®
Is the HDMI cable you are
Use a High Speed HDMI Cable. The Control function may not work
®
®
using a High Speed HDMI
Cable?
properly if an HDMI cable other than a High Speed HDMI Cable is
used.
Is this player connected to
If video signals are being output from a terminal other than the HDMI
the TV using an HDMI cable OUT terminal, the Control function does not work. Connect to the TV
to watch the picture?
using an HDMI cable (page 15).
For the BDP-LX55:
Is the HDMI Mode set
appropriately?
When both of the HDMI OUT terminals (MAIN and SUB) are used, the
Control function only works for the HDMI OUT (SUB) terminal
(page 16).
Is Control set to On on the Set Control to On on the player (page 41).
player?
Does the connected device • The Control function will not work with devices of other brands that
support the Control function? do not support the Control function, even when connected using an
HDMI cable.
• The Control function will not work if devices that do not support the
Control function are connected between the Control-compatible device
and the player.
• See page 16.
• Even when connected to a Pioneer product compatible with the
Control function, some of the functions may not work.
Also refer to the operating instructions for the connected device.
Is Control set to On on the
connected device?
Set Control to On on the connected device. The Control function
operates when Control is set to On for all devices connected to the
HDMI OUT terminal.
Once connections and settings of all the devices are finished, be sure
to check that the player’s picture is output to the Flat Screen TV. (Also,
check after changing the connected devices and connecting and/or
disconnecting HDMI cables.) If the player’s picture is not being output
to the Flat Screen TV, the Control function may not work properly.
For details, refer to the operating instructions of the connected device.
Are multiple players
connected?
The Control function may not work if three or more players, including
this player, are connected by an HDMI cable.
Network
Problem
Check
Remedy
• BD-LIVE function
(connection to the Internet)
cannot be used.
Perform Connection Test (page 45). If “Networks is OK.” is displayed,
check the proxy server settings (page 44). Also, there may be a problem
with the Internet connection. Contact your Internet service provider.
• “No valid id file found!” is
displayed when I try to update
the software.
Software updating is slow.
Depending on the Internet connection and other conditions, some time
may be required to update the software.
58
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Check
Remedy
08
A message other than
“Networks is OK.” is
Is “Network is FAILED.”
displayed?
• Check that this player and the Ethernet hub (or router with a hub
functionality) are properly connected.
displayed when Connection
Test is performed.
• If the IP address is obtained using the DHCP server function, check
the setting is correct at the Information (page 41). For details on the
DHCP server function, see the operating instructions for the Ethernet
hub (or router with a hub functionality).
• Set the IP address manually.
• Check the operation and settings of the DHCP server function of the
Ethernet hub (or router with hub functionality). For details on the DHCP
server function, see the operating instructions for the Ethernet hub (or
router with a hub functionality).
• If this player has been set manually, reset the IP address of this player
or other components.
Is the Ethernet hub (or router • Check the settings and operation the Ethernet hub (or router with a
with a hub functionality)
operating properly?
hub functionality). For details, see the operating instructions for the
Ethernet hub.
• Reboot the Ethernet hub (or router with a hub functionality).
Others
Problem
Check
Remedy
The player’s power turns off Is Auto Power Off set to 10 If Auto Power Off is set to 10 min/20 min/30 min, the player’s power
automatically.
min/20 min/30 min?
turns off automatically if no operation is performed for over 30 minutes
(page 43).
The player’s power turns on Is Control set to On?
automatically.
The player’s power may turn on together with the power of the TV
connected to the HDMI OUT terminal. If you do not want the player’s
power to turn on when the TV’s power is turned on, set Control to Off
(page 41).
The player cannot be
operated with the remote
control.
Are you operating the remote Operate from within 7 m of the remote control sensor.
control from a point too far
away from the player?
Are the batteries dead?
Replace the batteries (page 5).
Input of the connected TV
and AV system switches
automatically.
Is Control set to On?
The input of the TV and AV system (AV receiver or amplifier, etc.)
connected to the HDMI OUT terminal may automatically switch to the
player when playback starts on the player or the menu screen (Home
Media Gallery, etc.) is displayed. If you do not want the inputs of the
connected TV and AV system (AV receiver or amplifier, etc.) to switch
automatically, set Control to Off (page 41).
Settings I have made have
been cleared.
• Have you disconnected the Always press STANDBY/ON on the player’s front panel or
power cord while the player’s STANDBY/ON on the remote control and check that POWER OFF
power was on?
has turned off from the player’s front panel display before
disconnecting the power cord. Be particularly careful when the power
cord is connected to the AC outlet on another device because the
player turns off in conjunction with the device.
• Has there been a power
failure?
59
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Check
Remedy
08
USB(external storage)device Is the USB device properly
does not work with this player connected?
properly.
• Turn the player’s power off, then turn the power back on.
• Turn the player’s power off, then reconnect the external storage
device (page 21).
Is the USB device connected Do not use an extension cable. The player may not work properly with it.
via an extension cable?
Is the external storage device External storage device may not work if connected to the USB port via
connected to the USB port via a memory card reader or USB hub.
a memory card reader or USB
hub?
Does the external storage
device contain multiple
partitions?
External storage devices may not be recognized if they contain multiple
partitions.
Some external storage devices may not operate.
Is the external storage device Turn the player’s power off, then disable the write-protection.
write-protected?
Is the external storage
Only external storage devices with a FAT16 or FAT32 file system can be
device’s file system FAT16 or used.
FAT32?
Turn the player’s power off, then turn the power back on.
Default Gateway
Glossary
A default gateway is a communication device such as a router
which passes data between networks. It is used to direct data to
networks on which the destination gateway is not explicitly
specified.
Angle (Multi angle)
Up to 9 camera angles can be recorded simultaneously on BD-
ROM or DVD-Video discs, letting you view the same scene from
different angles.
DHCP (Dynamic Host Configuration
Protocol)
This protocol provides configuration parameters (IP address,
etc.) for computers and other devices connected to the network.
AVCHD (Advanced Video Codec High
Definition)
See page 9.
DivX
See page 10.
AVCREC
See page 9.
DNS (Domain Name System)
This is a system for associating Internet host names with IP
addresses.
BDAV
Of the BD format, the Audio Visual Format Specifications for HD
digital broadcast recording is referred to as BDAV on this player
and in these operating instructions.
Dolby Digital
Dolby Digital is an audio format to record the sound in up to 5.1
channels with a fraction of the amount of data as compared to
linear PCM audio signals.
BD-J
See page 9.
Dolby Digital Plus
BD-LIVE
Dolby Digital Plus is an audio format for high-definition media.
Built on Dolby Digital, it combines the efficiency and flexibility to
provide high quality multi-channel audio. With BD-ROMs, up to
7.1 channels of digital sound can be recorded.
See page 8.
BDMV
Of the BD format, the Audio Visual Format Specifications
designed for pre-packaged high definition (HD) movie contents is
referred to as BDMV on this player and in these operating
instructions.
Dolby TrueHD
Dolby TrueHD is an audio format using lossless coding. With BD-
ROMs, up to 8 channels can be recorded at 96 kHz/24 bits, or up
to 6 channels at 192 kHz/24 bits.
BONUSVIEW
See page 8.
DRM
A technology for protecting copyrighted digital data. Digitized
videos, images and audio retain the same quality even when they
are copied or transferred repeatedly. DRM is a technology for
restricting the distribution or playback of such digital data
without the authorization of the copyright holder.
Deep Color
See page 15.
60
En
Download from Www.Somanuals.com. All Manuals Search And Download.
DTS Digital Surround
DTS Digital Surround is an audio format to record 48 kHz/24 bits
audio signals in 5.1 channels.
Port number
This is a sub-address provided below the IP address for
simultaneously connecting to multiple parties during Internet
communications.
08
DTS-HD High Resolution Audio
Progressive scan
DTS-HD High Resolution Audio is an audio format using lossy
coding. It can record 7.1 channels at 96 kHz/24 bits.
With this method, one picture is consisted of a single picture,
without dividing it in two pictures. Progressive scan provides
clear pictures with no flicker, in particular for still pictures that
contain much text, graphics, or horizontal lines. Progressive scan
is indicated in this player and operating instructions by a “p” after
the resolution value (for example, 576p).
DTS-HD Master Audio
DTS-HD Master Audio is an audio format using lossless coding.
With BD-ROMs, 7.1 channels can be recorded at 96 kHz/24 bits,
or 5.1 channels at 192 kHz/24 bits.
Proxy server
This is a relay server for ensuring fast access and safe
communications when connecting to the Internet from an
internal network.
Ethernet
A standard for local area networks (LANs) used to connect
multiple computers, etc. in the same location. This player
supports 100BASE-TX.
Region number
Frames and fields
See page 9.
A frame is the unit for one of the still pictures which compose
motion pictures. One frame consists of a picture of odd lines and
a picture of even lines called fields in video signal with interlaced
scan method (576i, 1080i, etc.).
Secondary audio
Some BD-ROMs include sub audio streams mixed with the main
audio stream. These sub audio streams are called “secondary
audio”. On some discs this secondary audio is recorded as the
audio for the secondary video.
HDMI (High-Definition Multimedia
Interface)
See page 15.
Secondary video
Some BD-ROMs include sub videos superimposed on the main
videos using the Picture-in-Picture function. These sub videos are
called “secondary video”.
Interactive audio
The audio signals recorded in the titles of BD-ROMs. They include
for example the clicking sound made when the menu screen is
operated.
Subnet mask
This is used to identify which part of the IP address corresponds
to the subnet (a separately managed network). The subnet mask
is expressed as ‘255.255.255.0’.
Interlaced scan
With this method, one picture is displayed by scanning it twice.
The odd lines are displayed in the first pass, the even lines are
displayed in the second, to form a single picture (frame).
Interlaced scan is indicated in this player and operating
instructions by an “i” after the resolution value (for example, 576i).
USB (Universal Serial Bus)
USB is the industry standard for connecting peripherals to PCs.
VC-1
IP address
An address that identifies a computer or other device connected
to the Internet or local area network. It is represented a number
in four sections.
A video codec developed by Microsoft and standardized by the
Society of Motion Picture and Television Engineers (SMPTE).
Some BDs include videos encoded in this codec.
x.v.Color
See page 15.
Linear PCM
This is referred as the audio signals that are not compressed.
MAC (Media Access Control) address
A hardware identification number assigned specifically to the
network device (LAN card, etc.).
MPEG (Moving Picture Experts Group)
The name of a family of standards used to encode video and
audio signals in a digital compressed format. The video encoding
standards include MPEG-1 Video, MPEG-2 Video, MPEG-4 Visual,
MPEG-4 AVC, etc. The audio encoding standards include MPEG-
1 Audio, MPEG-2 Audio, MPEG-2 AAC, etc.
Parental Lock
See page 46.
Picture-in-Picture (P-in-P)
This is a function for superimposing a sub video on the main
video. Some BD-ROMs include secondary video, which can be
superimposed on the primary video.
61
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
08
Model
BDP-LX55
BDP-440
BDP-140
TM
Type
Blu-ray 3D PLAYER
Rated voltage
AC 100 V to 240 V
AC 110 V to 240 V (Duty-free model in Japan only)
50 Hz/60 Hz
Rated frequency
Power consumption
BDP-LX55: 25 W
BDP-440, BDP-140: 23 W
Power consumption (standby)
Weight
BDP-LX55: 0.5 W
BDP-440, BDP-140: 0.3 W
BDP-LX55: 3.5 kg
BDP-440: 2.6 kg
BDP-140: 2.1 kg
External dimensions (including projecting parts)
BDP-LX55: 435 mm (W) x 93 mm (H) x 252 mm (D)
BDP-440: 435 mm (W) x 90 mm (H) x 252 mm (D)
BDP-140: 435 mm (W) x 58 mm (H) x 249 mm (D)
+5 °C to +35 °C
Tolerable operating temperature
Tolerable operating humidity
HDMI
5 % to 85 % (no condensation)
BDP-LX55: 2 set, 19-pin: 5 V, 250 mA
BDP-440, BDP-140: 1 set, 19-pin: 5 V, 250 mA
1 set, RCA jack: 1.0 Vp-p (75 Ω)
1 set, RCA jacks
Video outputs
Audio outputs
2-channel (left/right)
Audio output level
Frequency response
200 mVrms (1 kHz, –20 dB)
4 Hz to 88 kHz (192 kHz sampling)
1 set, Optical digital jack
Digital audio outputs Optical
LAN
USB
1 set, Ethernet jack (10BASE-T/100BASE-TX)
2 set, Type A
Note
• The specifications and design of this product are subject to change without notice.
62
En
Download from Www.Somanuals.com. All Manuals Search And Download.
08
63
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|