Optimus Car Stereo System Dec 52 User Manual

12-2152.fm Page 1 Wednesday, July 14, 1999 2:48 PM

Cat. No. 12-2152

OWNER’S MANUAL

Please read before using this equipment.

High-Power In-Dash

AM/FM Stereo CD Player

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 3 Wednesday, July 14, 1999 2:48 PM

The CD player in this stereo system is

made and tested to meet exacting

safety standards. It meets FCC re-

quirements and complies with safety

performance standards of the U.S.

Department of Health and Human

Services.

GENERAL

Anti-Theft Control Panel — lets you

quickly remove and store the stereo

control panel in the supplied carry

case. This discourages theft because

the stereo cannot operate without the

control panel.

Warnings:

Five Preset Equalizer Settings —

provide you with common sound set-

tings for enhancing rock, jazz, pop,

classical, or country and western mu-

sic. The equalizer settings also en-

hance any kind of music.

• This system employs a laser light

beam. Only a qualified service

person should remove the cover

or attempt to service this device,

due to possible eye injury.

• The use of controls, adjustments,

or procedures other than those

specified herein might result in

hazardous radiation exposure.

Electronic Bass, Treble, Fader, and

Balance Controls — let you adjust

high and low sounds and the balance

between the left/right and front/rear

speakers by pressing a few buttons,

so you can tailor the sound to suit your

preferences.

Line-Out Jacks — make it easy to

connect a booster.

We recommend you record your ste-

reo’s serial number here. The number

is on the top panel of the stereo.

Serial Number: _________________

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 4 Wednesday, July 14, 1999 2:48 PM

CONTENTS

Installation ............................................................................................................. 6

Before You Begin the Installation ..................................................................... 6

Preparing the Mounting Area .................................................................... 6

Routing Speaker Wires ............................................................................. 6

Removing the Shipping Screw .................................................................. 6

Making the Connections................................................................................... 7

Using an Adapter Harness ........................................................................ 8

Connecting Ground, Power, and Optional Components ........................... 8

Connecting an Equalizer/Booster ............................................................. 9

Connecting Two Pairs of Speakers ........................................................... 9

Connecting One Pair of Speakers .......................................................... 10

Connecting the Antenna ......................................................................... 10

Completing the Connections ................................................................... 11

Testing the Connections ................................................................................. 11

Mounting the Stereo ....................................................................................... 11

Removing the Stereo from the Dash .............................................................. 13

Using the Control Panel ..................................................................................... 14

Installing the Control Panel............................................................................. 14

Removing the Control Panel........................................................................... 14

Basic Operation .................................................................................................. 15

Setting the Clock ............................................................................................ 15

Adjusting the Controls .................................................................................... 15

Selecting a Preset Equalizer Setting........................................................ 16

Displaying the Clock....................................................................................... 16

Resetting the Stereo....................................................................................... 17

Turning the Stereo’s Beep On and Off ........................................................... 17

Radio Operation .................................................................................................. 18

Playing the Radio ........................................................................................... 18

Memory Tuning............................................................................................... 19

Manually Storing Stations ....................................................................... 19

Storing Stations in Automatic Travel Programming Memory .................. 19

Selecting a Stored Station ...................................................................... 20

Scanning Stored Stations ....................................................................... 20

CD Player Operation ........................................................................................... 21

Playing a CD................................................................................................... 21

Selecting a Track............................................................................................ 22

Audible Search ............................................................................................... 22

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 5 Wednesday, July 14, 1999 2:48 PM

Shuffle Play.................................................................................................... 22

Scanning the Tracks ...................................................................................... 22

Repeat Play ................................................................................................... 23

Switching Between the CD and the Radio ..................................................... 23

Troubleshooting ................................................................................................. 24

Care and Maintenance ....................................................................................... 25

The FCC Wants You to Know ........................................................................ 25

CD Care Tips ................................................................................................. 26

Replacing a Fuse ........................................................................................... 26

Specifications ..................................................................................................... 28

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 6 Wednesday, July 14, 1999 2:48 PM

INSTALLATION

RadioShack store. Follow the

installation kit’s instructions to

mount the stereo.

BEFORE YOU BEGIN

THE INSTALLATION

Before you install your stereo, read all

the instructions in this owner’s manu-

al. You should be able to answer all of

these questions about your vehicle’s

electrical and sound systems.

Cautions:

• Make sure your vehicle’s mount-

ing area is as level as possible. If

you cannot mount the stereo

exactly level, make sure the ste-

reo will not tilt up more than 30

degrees when it is mounted.

• Which of the stereo’s wires is the

power wire?

• Which terminal in my vehicle’s

fuse box is for accessories?

• Be sure to avoid obstructions be-

hind the mounting surface.

• How do I connect a wire to the

fuse box?

Routing Speaker Wires

• Which stereo wires are line-level

outputs and which are speaker

outputs?

If you install speakers, avoid routing

the speaker wires near moving parts

or sharp edges. You can usually route

them along the wiring channel be-

neath the vehicle’s door facings by

carefully removing the molding that

holds the carpet in place. After you

route the speaker wires, replace the

molding.

Also, be aware that installation in your

vehicle might require cutting or modi-

fying your vehicle.

Preparing the Mounting Area

Before you mount the stereo, make

sure you have all the necessary mate-

rials. Then confirm that the stereo fits

your vehicle’s mounting area.

Removing the Shipping Screw

The shipping screw helps protect the

stereo’s CD player from being dam-

aged during shipment.

Notes:

• This autosound stereo system is a

DIN-E size unit that requires a 2¹/⁴-

inch (57 mm) high by 7¹/²-inch

(190 mm) wide by 7¹/⁴-inch (186

mm) deep mounting area.

Before you mount the stereo, use a

small Phillips screwdriver to remove

the shipping screw from the top of the

stereo.

• If the mounting area is too large,

you might be able to mount the

stereo with an in-dash installation

kit, available at your local

If you do not remove the shipping

screw, you cannot remove the sup-

plied sleeve from the stereo and the

CD player will not work.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 7 Wednesday, July 14, 1999 2:48 PM

Cautions:

• For added safety and to protect

your stereo, disconnect the cable

from your vehicle battery’s nega-

tive (–) terminal before you begin.

(illus)

Note: Save the shipping screw in

case you ever want to mail or ship the

stereo. You can secure it to the back

of the stereo with a piece of tape.

• Be sure your speakers can handle

64 watts of power (16 watts per

channel). Each speaker must

have an impedance of at least 4

ohms. Your local RadioShack

store carries a full line of speak-

ers.

MAKING THE

CONNECTIONS

The supplied harness with the 14-pin

connector includes all the lead wires

you need to connect the stereo to

ground, power, some optional compo-

nents, and speakers.

• You must connect the GROUND,

+12V TO IGNITION, and +12V TO

BATTERY wires first, then make

all other connections as described

in the following sections before

you plug the harness with the 14-

pin connector into the stereo. If

you do not make connections in

the order shown, damage to the

stereo is possible if any wire con-

nections are made incorrectly.

Important: Do not cut these wires. If

you cut any wire, you cannot obtain a

refund or exchange on this product.

RadioShack will provide warranty ser-

vice if you cut a wire and find the prod-

uct is defective.

• You must connect a separate wire

to each speaker terminal as

described in the following proce-

dure. Do not use a common wire

or chassis ground for any speaker

connection.

You might need additional wire, de-

pending on your individual auto sound

system, to complete the connections.

Your local RadioShack store carries a

full line of wire and wire management

accessories.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 8 Wednesday, July 14, 1999 2:48 PM

Note: The wiring harness has the fol-

lowing labels.

Connecting Ground, Power,

and Optional Components

Follow these steps to connect the har-

ness with the 14-pin connector to

ground, primary and memory backup

power, and optional components.

(illus - (Black) Ground

(Red) +12V to Ignition

(Yellow) +12V to Battery

(Blue/White) Amp Remote

Turn On 500 mA Max

(White) Front Left Speaker +

(White/Black) Front Left Speaker -

(Gray) Front Right Speaker +

(Gray/Black) Front Right Speaker -

(Green) Rear Left Speaker +

(illus - show (Black) Ground

(Red) Power

(Yellow) Power/Memory

(Blue/White) Optional

Equipment

Speaker -

(Green/Black) Rear Left

(Violet) Rear Right Speaker +

Speaker -

(Violet/Black) Rear Right

Using an Adapter Harness

1. Disconnect the cable from your

–

vehicle battery’s negative ( ) ter-

minal.

If you are replacing an existing stereo,

or if your vehicle has been factory-

wired for autosound components, you

might be able to use an adapter har-

ness to connect the power and speak-

ers. RadioShack stores sell adapter

harnesses for most vehicles.

2. Connect the black ground wire to

a chassis ground, such as a metal

screw attached to a metal part of

the vehicle’s frame. Be sure that

the screw is not insulated from the

chassis by a plastic part.

Follow the directions that come with

the adapter harness to temporarily

connect the power and speakers.

3. Connect the red power wire (with

in-line fuse holder) to a point in

your vehicle’s fuse block that has

power only when you turn the

vehicle’s key to either the acces-

sory (ACC) or START position.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 9 Wednesday, July 14, 1999 2:48 PM

This connection turns on the ste-

reo when you turn on the ignition

or turn the key to ACC, and turns

off the stereo when you turn off

the ignition. This prevents your

vehicle’s battery from being

drained if you leave the stereo on

when you turn off the ignition.

Connecting an Equalizer/

Booster

If you are connecting the stereo to a

separate equalizer or booster, you

need additional wires (not included).

To increase the total power output

from your system, connect the R

(right) and L (left) line output jacks on

the back of the stereo and blue/white

wire, if necessary, to the equalizer or

booster.

4. Connect the yellow power/mem-

ory wire (with transformer and in-

line fuse holder) to your vehicle

battery’s positive (+) terminal or to

a point in your vehicle’s fuse block

that provides a continuous source

of 12 volts.

(illus - show (Blue/White)

Booster

This connection provides power

for the stereo’s components, and

continuous power for the stereo’s

memory when the ignition is

turned off.

(Right) R

(Left) L

5. Connect the blue/white wire to any

optional equipment, designed to

run from a switched source, that

you want the stereo to turn on and

off (such as a booster or a power

antenna).

Check the equalizer/booster’s owner’s

manual for directions.

This wire does not provide power

to the components. It simply turns

them on or off. If you do not use

this wire, secure it with a wire tie

and do not let it touch metal.

Connecting Two Pairs of

Speakers

If you are using both front and rear

speakers, follow these steps to con-

nect the harness with the 14-pin con-

nector to the speakers.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 10 Wednesday, July 14, 1999 2:48 PM

Connecting One Pair of

Speakers

(illus - (White) (White/Black)

Front Left Speaker

If you are using only one pair of

speakers, follow Steps 1-4 on the left

to connect the harness with the 14-pin

connector to the speakers.

(Gray) (Gray/Black)

Front Right Speaker

(Green) (Green/Black))

Rear Left Speaker

(Violet) (Violet/Black))

Rear Right Speaker

(illus - (White) (White/Black)

Left Speaker

(Gray) (Gray/Black)

Right Speaker

1. Connect the gray wire to the right

front speaker’s positive terminal.

This terminal is usually marked

with a plus (+) sign or red mark.

(Green) (Green/Black))

Do not Connect

(Violet) (Violet/Black))

Do not Connect

2. Connect the gray/black wire to the

right front speaker’s negative ter-

minal. This terminal might be

marked with a minus (–) sign or it

might not be marked at all.

Connecting the Antenna

3. Connect the white wire to the left

front speaker’s positive terminal.

Connect the vehicle’s antenna cable

to the stereo’s large black antenna

connector.

4. Connect the white/black wire to

the left front speaker’s negative

terminal.

5. Connect the violet wire to the right

rear speaker’s positive terminal.

(illus)

6. Connect the violet/black wire to

the right rear speaker’s negative

terminal.

7. Connect the green wire to the left

rear speaker’s positive terminal.

8. Connect the green/black wire to

the left rear speaker’s negative

terminal.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 11 Wednesday, July 14, 1999 2:48 PM

After you verify that the display lights,

follow the instructions in “Mounting the

Stereo.”

Completing the Connections

Make sure you have securely made all

other connections, then plug the har-

ness’ connector into the stereo’s 14-pin

wiring socket. Reconnect the cable to

the vehicle battery’s negative terminal.

MOUNTING THE STEREO

Be sure you verify that the stereo is

connected properly. See “Making the

Connections” on Page 7. Then follow

these steps to mount the stereo.

(illus)

1. Disconnect the cable from the

vehicle battery’s negative (–) ter-

minal.

(new illus)

TESTING THE

CONNECTIONS

2. Disconnect the wire harness and

the antenna.

Turn on your vehicle’s ignition and in-

stall your stereo’s control panel (see

“Installing the Control Panel” on

Page 14). The display should light

when you press ON/OFF to turn on the

stereo.

(new illus)

If the stereo does not work, immedi-

ately disconnect the cable from

your vehicle battery’s negative (–)

terminal. Then recheck your connec-

tions.

3. Press RLS on the lower right-hand

corner of the control panel to

remove the control panel.

Caution: If you played a CD while

testing the connections, be sure to re-

move the CD from the stereo before

continuing.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 12 Wednesday, July 14, 1999 2:48 PM

4. Insert both of the supplied keys

into the slots at the left and right

sides of the stereo. Press the keys

downward, and slide the sleeve

off of the stereo.

(illus)

8. Reconnect the wire harness and

the antenna.

9. Slide the stereo into the sleeve

until it locks into place.

Note: The keys are labeled to

show their top edges.

10. If you are securing the stereo in

an existing mounting hole under

the dash, push the supplied rub-

ber mounting grommet onto the

mounting bolt, then push the

mounting bolt (covered by the

mounting grommet) through the

existing mounting hole and make

sure it is secure.

5. Remove the keys from the slots.

6. Insert the sleeve into the dash.

Then secure the sleeve to the

dash by bending out the tabs with

a screwdriver. Bend out all the

side tabs.

(illus)

(illus - show mounting grommet)

7. If your vehicle has an existing

mounting hole under the dash,

use pliers or a /¹⁶-inch box-end

wrench to attach the short end of

the supplied mounting bolt to the

back of the stereo.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 13 Wednesday, July 14, 1999 2:48 PM

Otherwise, you can use one of the

supplied bolts (with attached

washer) to attach one end of the

supplied metal strap to the mount-

ing hole on the back of the stereo.

If necessary, bend the metal strap

to fit your vehicle’s mounting area.

Then use either the supplied

sheet metal screws or the other

bolt (with attached washer) to

attach the other end of the strap to

a solid metal part of the vehicle

under the dashboard. This strap

also helps ensure proper electrical

grounding of the stereo.

2. If you secured the stereo to an

existing mounting hole under the

dash, slide out the stereo to free

the mounting bolt from the mount-

ing hole.

Or, remove the bolt holding the

metal strap attached to the back

of the stereo.

RLS

3. Press

to remove the stereo’s

control panel.

4. Insert both of the supplied keys

into the slots at the left and right

sides of the stereo. Press the keys

downward and slide the stereo out

of the dash.

(illus - show bolt (with attached

washers))

(illus - show keys on slots)

11. Reconnect the cable to the vehi-

cle battery’s negative (–) terminal.

5. Remove the keys from the slots.

6. Disconnect the wire harness and

the antenna.

REMOVING THE STEREO

FROM THE DASH

7. If you are mailing or shipping the

stereo, use a small Phillips screw-

driver to reinstall the shipping

screw in the top of the stereo.

If you ever want to remove the stereo

from the dash, follow these steps.

8. Reconnect the cable to the vehi-

cle battery’s negative (–) terminal.

1. Disconnect the cable from the

vehicle battery’s negative (–) ter-

minal.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 14 Wednesday, July 14, 1999 2:48 PM

USING THE CONTROL PANEL

The stereo’s control panel must be in

REMOVING THE

CONTROL PANEL

place for the stereo to operate. When

you remove it, the display turns off

and the stereo cannot be used. This is

a simple, but effective security mea-

sure.

1. Press RLS until you hear a click.

The control panel swings out.

Any stored stations remain in memory

when the control panel is removed.

(illus - show control panel swing)

INSTALLING THE

CONTROL PANEL

1. Insert the left edge of the control

panel into the left edge of the

recess. The pins and holes in the

control panel interlock with the

pins and holes in the recess.

2. Remove the control panel, then

store it in the supplied carry case.

(illus - show pins in recess holes)

(illus)

Caution: To keep the metal connect-

ing pins clean, do not touch the con-

necting pins in the recess or on the

back of the control panel.

2. Gently push the right edge of the

control panel into the recess until

you hear a click.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 15 Wednesday, July 14, 1999 2:48 PM

BASIC OPERATION

Notes:

• The clock resets the seconds to 0

SETTING THE CLOCK

1. Press ON/OFF to turn on the ste-

as soon as you stop advancing

the minute or hour.

reo.

2. While pressing and holding down

CLOCK, repeatedly press TUNE/

SEEK TRACK – until the stereo

displays the correct hour. To

quickly advance the hour, press

and hold down TUNE/SEEK

TRACK –.

• You can use a watch with a

sweep-second hand or other time

reference to set the clock to the

exact second at the beginning of

an hour. When the time reference

reaches the beginning of an hour,

press and hold down CLOCK, then

press 6. The clock resets the min-

utes and seconds to 00 and

advances the hour if the minutes

were past 29.

(illus)

ADJUSTING THE

CONTROLS

When you listen to your stereo, adjust

these controls to suit your listening

preferences.

3. While pressing and holding down

CLOCK, repeatedly press TUNE/

SEEK TRACK + until the stereo

displays the correct minute. To

quickly advance the minute, press

and hold down TUNE/SEEK

TRACK +.

(illus)

ON/OFF — Press until the display

lights to turn on the stereo. To turn off

the stereo, press ON/OFF again.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 16 Wednesday, July 14, 1999 2:48 PM

AUDIO CONTROL +/– — Repeatedly

press to increase or decrease the vol-

ume. VOLand a volume level number

appear on the display.

tings, press and hold down AUDIO

CONTROL SEL for about 3 sec-

onds until the stereo beeps twice.

Selecting a Preset Equalizer

Setting

To protect your hearing, do

Warning:

not listen at high volume levels. Slowly

increase the volume to a comfortable

listening level.

The stereo has preset graphic equaliz-

er settings to let you vary the balance of

the sound it produces. These settings

are designed to give you the best

sound for jazz, pop, rock, classical, and

country and western music.

AUDIO CONTROL SEL — Repeatedly

press until BAS, TRE, BAL, or FAD

and a number appear on the display,

then repeatedly press AUDIO CON-

TROL + or – within 5 seconds to

change the stereo’s bass, treble, bal-

ance, or fader settings.

To select a graphic equalizer set-

ting, repeatedly press P-EQ until

ROC (rock), JAZ (jazz), POP (pop),

CLS (classic), or C W (country and

western) appears on the display.

The P-EQ indicator turns on to show

that you have selected a graphic

equalizer setting.

Notes:

• When you adjust the balance

toward the left speakers, Land a

number appear on the display.

When you adjust the balance

toward the right speakers, Rand a

number appear on the display.

To turn off equalization, press P-EQ

until DFT(defeat) appears on the dis-

play. The P-EQ indicator turns off.

• When you adjust the fader toward

the front speakers, F and a num-

ber appear on the display. When

you adjust the fader toward the

rear speakers, R and a number

appear on the display.

The graphic equalizer setting or

Note:

DFT disappears from the display af-

ter about 5 seconds or when you

press another button.

• If BAS, TRE, BAL, or FADand the

number disappear before you

press AUDIO CONTROL + or –,

repeatedly press AUDIO CON-

TROL SEL until the setting you

want reappears, then repeatedly

press AUDIO CONTROL + or – to

set it.

DISPLAYING THE CLOCK

While the radio or a CD is playing,

press CLOCK to display the clock. The

stereo displays the clock for 5 sec-

onds, then returns to the radio or CD

display.

• To set bass, treble, balance, and

fader to their center (middle) set-

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 17 Wednesday, July 14, 1999 2:48 PM

Note: If you eject a CD while it is play-

ing and do not remove it from the CD

player, the stereo displays NO Cd. If

you eject a CD then remove it from the

CD player, the stereo shows the clock.

TURNING THE

STEREO’S BEEP ON

AND OFF

The stereo normally beeps when you

press most buttons. To turn the ste-

reo’s beep on or off, eject a CD if one

is loaded (see “CD Player Operation”

on Page 21). Then press and hold

RESETTING THE

STEREO

down

for about 3 seconds until the

If your stereo locks up or does not

work properly, use something pointed,

such as a straightened paper clip, to

stereo beeps twice.

RESET

press

for about 1 second.

(illus)

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 18 Wednesday, July 14, 1999 2:48 PM

RADIO OPERATION

Manual Tuning: Repeatedly

press TUNE/SEEK TRACK – or +

to tune down or up the selected

band.

PLAYING THE RADIO

1. Press ON/OFF to turn on the ste-

reo. The radio automatically tunes

to the last station and band

selected.

Seek Tuning: Press and hold

down TUNE/SEEK TRACK – or +

for about 1 second to tune to the

next lower or higher station.

Note: If DX appears on the dis-

play, the stereo stops on both

strong and weak FM stations. To

limit seek tuning to only strong FM

stations, press LO/DX so DX dis-

appears.

(illus)

Note: If you ejected a CD just

before turning off the stereo, the

display shows the time.

4. Press AUDIO CONTROL + or – to

increase or decrease the volume

as desired.

2. Press BAND to select the desired

band. AM appears on the display

when the AM band is selected.

FMIor FMIIappears on the dis-

play when an FM band is

selected.

(illus)

Notes:

(illus)

• ST appears on the display when

an FM signal is received in stereo.

• See “Adjusting the Controls” on

Page 15 for information about

changing the stereo’s other set-

tings.

3. Tune to the desired station in one

of the following ways.

(illus)

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 19 Wednesday, July 14, 1999 2:48 PM

Storing Stations in Automatic

Travel Programming Memory

MEMORY TUNING

You can manually store up to 6 AM

and 12 FM stations in memory groups.

Each memory group (AM, FMI, and

FMII) holds up to six stations. You can

also automatically store the first 6

strong AM and first 6 strong FM sta-

tions in a separate automatic travel

programming memory.

The stereo can store the first 6 strong

AM and the first 6 strong FM stations it

finds into its automatic travel program-

ming memory. This memory is sepa-

rate from the stereo’s memory groups,

so it does not replace the stations you

manually stored.

BAND

1. Repeatedly press

to select

Manually Storing Stations

the desired band (AM for AM, or

FMI or FMIIfor FM).

BAND

1. Repeatedly press

to select

the desired memory group (AMfor

TUNE/SEEK

2. Press and hold down

AM, or FMI or FMIIfor FM).

TRACK ATP

(automatic travel pro-

gramming) for about 2 seconds.

The stereo displays AS, scans the

selected band, and automatically

stores the first 6 strong stations it

finds in automatic travel program-

ming memory.

2. Use either seek or manual tuning

to tune to the station you want to

store.

Note: To tune both strong and

LO/DX

weak FM stations, press

DX appears. To tune only strong

LO/DX

FM stations, press

disappears.

so DX

3. Press and hold down the desired

memory channel button until the

memory channel number, ch, and

the frequency flash once on the

display. The station is stored.

(illus)

After the stereo stores all six sta-

tions in the selected band, it tunes

to the station stored in channel 1

in automatic travel programming

memory.

(illus - callout ‘Memory Channel

Buttons)

Note: If the stereo could not find

any stations, - - - and the

channel number appears on the

BAND

display. Press

or select

another station to listen to the

radio.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 20 Wednesday, July 14, 1999 2:48 PM

3. Press and release TUNE/SEEK

TRACK ATP so AS disappears

from the display.

Scanning Stored Stations

The radio can scan all stored stations

in the selected band, pausing for 5

seconds at each station.

Selecting a Stored Station

To start scanning stored stations,

repeatedly press BAND to select the

desired memory group, then press

P-SCAN.

To select a station you manually

stored in AM, FMI, or FMII, repeatedly

press BAND to select the desired

memory group, then press the desired

memory channel button.

To scan the stations in the automatic

travel programming memory, press

BAND to select the desired band,

press TUNE/SEEK TRACK ATP so AS

appears on the display, then press P-

SCAN.

Do not hold down the memory

Note:

channel button. This stores the cur-

rently tuned station into that location.

Follow these steps to select a station

you automatically stored in automatic

travel programming memory.

1. Repeatedly press BAND to select

the desired band (AM for AM, or

FMIor FMIIfor FM).

(illus - call out P-SCAN button)

2. Press TUNE/SEEK TRACK ATP

until ASappears on the display.

As the radio scans each memory

channel, the channel number flashes

and the frequency is displayed. After

scanning all memory channels, the

stereo returns to the original station.

Do not hold down TUNE/

Note:

SEEK TRACK ATP. This causes the

stereo to automatically scan and

store the first 6 strong stations it

finds into its automatic travel pro-

gramming memory.

To stop the scanning when the radio

pauses at a station you want to listen

to, press P-SCAN again.

3. Press the desired memory chan-

nel button.

If the stereo could not find

Note:

any strong stations, - - - and

the channel number appear on

the display if you try to tune to an

automatic travel programming

memory channel.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 21 Wednesday, July 14, 1999 2:48 PM

CD PLAYER OPERATION

Cautions:

If a CD is already in the CD player,

simply press CD to play the CD.

The stereo displays CD, DISC

IN, TR:, and the track number of

the track you last played, and the

CD starts to play from the point

where you last stopped it.

• Play only CDs that

have this mark on

them:

• The CD player has

wide

dynamic range. As a result, if you

turn your stereo’s volume up too

high during soft (low volume) sec-

tions of a program, your speakers

might be damaged when a sud-

den loud passage occurs.

After the stereo plays the entire

CD, it automatically repeats all

tracks, starting with Track 1.

Note: If you turn off your vehicle’s

ignition when a CD is loaded, you

must wait about 2 seconds after

you turn the ignition back on before

you can press CD to play the CD.

• If the CD player is jolted during

play, the rotation speed might sud-

denly change or the CD player

might make an unusual noise.

This is not a malfunction.

3. Press AUDIO CONTROL + or – to

increase or decrease the volume

as desired.

Note: See “Adjusting the Con-

trols” on Page 15 for information

about changing the stereo’s other

settings.

PLAYING A CD

1. Press ON/OFF to turn on the ste-

reo.

4. To pause playback, press CD. The

stereo displays PAU, DISC IN,

TR:, and the track number. To

resume play, press CD again.

2. Insert a CD (label side up) in the

slot. The stereo displays DISC

IN, CD, and TR:01 and the CD

starts to play from Track 1.

Note: If you pause a CD for more

than 5 minutes, the stereo turns

itself off.

5. To remove a CD from the CD

(illus)

player, press

(illus)

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 22 Wednesday, July 14, 1999 2:48 PM

SHUF

To begin shuffle play, press

SELECTING A TRACK

The stereo displays DISC IN, SHF,

TR:, and the track number.

To select a track on the loaded CD,

TUNE/SEEK TRACK +

press

to advance to the next track or press

TUNE/SEEK TRACK –

during play

to go back to the

start of the current track. Repeatedly

TUNE/SEEK TRACK +

(illus - arrow SHUF key)

–

press

or to se-

lect the next or previous track.

AUDIBLE SEARCH

SHUF

To stop shuffle play, press

To search for a particular section of a

again to resume normal play. SHFdis-

TUNE/

track, press and hold down

appears.

SEEK TRACK + TUNE/SEEK TRACK

–

during play. The stereo rapidly plays

Note: You can use audible search

during shuffle play (see “Audible

Search”).

the CD either forward or backward

(like cueing or reviewing a cassette

tape). When you hear the section you

TUNE/SEEK TRACK +

want, release

TUNE/SEEK TRACK –

to resume nor-

mal play.

SCANNING THE TRACKS

You can set the stereo to play the first

10 seconds of each track on the load-

ed CD, so you can find the track you

want to listen to.

(illus - arrow TUNE SEEK TRACK)

SCAN

To begin scanning, press

. The

stereo displays DISC IN, SCN, TR:,

and the track number.

SHUFFLE PLAY

(illus - arrow SCAN key)

You can set the stereo to randomly

select and play tracks from the loaded

CD. After each track plays, the stereo

automatically selects another track

and plays it until you stop shuffle play.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 23 Wednesday, July 14, 1999 2:48 PM

To stop scanning, press SCAN again

at the desired track to resume normal

play. SCNdisappears.

SWITCHING BETWEEN

THE CD AND THE RADIO

You can temporarily stop a CD and lis-

ten to the radio by pressing BAND.

The CD stops and the radio tunes to

the last station selected.

REPEAT PLAY

You can set the stereo to repeat a sin-

gle track on the loaded CD.

To continue playing the CD, press CD.

To repeat a track, press RPT during

play. The stereo displays DISC IN,

RPT, TR:, and the track number.

When the track ends, it automatically

repeats play.

(illus - arrow RPT key)

To stop repeating the track, press RPT

again to resume normal play. RPTdis-

appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 24 Wednesday, July 14, 1999 2:48 PM

TROUBLESHOOTING

If your stereo’s CD player is not working as it should, it displays an error indicator. If it is

a numbered error, it ejects the loaded CD. Try these suggestions.

Indicator

Problem

Suggestion

Loading and/or unloading

operation fails.

Make sure a CD is loaded. If it

is not, insert the CD properly. If

it is, eject the CD and load it

again.

E01

The CD is loaded incorrectly. Reload the CD with the label

side up.

E07

The CD is dirty or defective.

Clean the CD (see “CD Care

Tips” on Page 26) or try anoth-

er CD.

Abnormal CD operation.

Contact your local RadioShack

store for assistance.

L Err

If the stereo still does not operate properly, the connecting pins in the recess or on

the back of the control panel might be dirty. Use a soft cloth or a contact cleaner

(such as Cat. No. 64-4340) to clean them.

(new illus)

If the stereo still does not operate properly, take it to your local RadioShack store

for assistance.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 25 Wednesday, July 14, 1999 2:48 PM

CARE AND MAINTENANCE

Your Optimus High-Power In-Dash AM/FM Stereo CD Player is an example of su-

perior design and craftsmanship. The following suggestions will help you care for the

stereo so you can enjoy it for years.

Keep the stereo dry. If it gets wet, wipe it dry immediately. Liquids can

contain minerals that can corrode electronic circuits.

Handle the stereo gently and carefully. Dropping it can damage the

circuit boards and case and can cause it to work improperly.

Keep the stereo away from dust and dirt, which can cause premature

wear of parts.

Wipe the stereo with a damp cloth occasionally to keep it looking

CLEANER

new. Do not use harsh chemicals, cleaning solvents, or strong deter-

gents to clean the stereo.

Modifying or tampering with the stereo’s internal parts can cause a malfunction and

might invalidate your stereo’s warranty and void your FCC authorization to operate

it. If your stereo is not performing as it should, take it to your local RadioShack store

for assistance.

THE FCC WANTS YOU TO KNOW

Your stereo might cause TV or radio interference even when it is operating proper-

ly. To determine whether your stereo is causing the interference, turn off your ste-

reo. If the interference goes away, your stereo is causing it. Try to eliminate the

interference by:

• Moving your stereo away from the receiver

• Contacting your local RadioShack store for help

If you cannot eliminate the interference, the FCC requires that you stop using your

stereo.

Download from Www.Somanuals.com. All Manuals Search And Download.

12-2152.fm Page 26 Wednesday, July 14, 1999 2:48 PM

CD CARE TIPS

REPLACING A FUSE

Even though a CD is very durable, you

should handle it with care. We recom-

mend the following precautions.

If the clock resets or stored stations

are lost when the ignition is off, you

might need to replace the yellow con-

tinuous power wire’s fuse with the

supplied spare fuse. If the stereo does

not operate, you might need to re-

place the red power wire’s fuse with

the supplied spare fuse. Check both

fuses.

• Keep the CD in its protective case

or sleeve when you are not play-

ing it.

• Handle a CD by its edges to avoid

fingerprints which can prevent the

CD player’s laser beam from

accurately reading the CD. Your

local RadioShack store sells a

suitable CD cleaner kit.

1. Disconnect the cable from the

vehicle battery’s negative (–) ter-

minal.

2. To open the yellow continuous

power wire’s fuse holder, pull the

latches apart until it opens. Then,

if the fuse is blown, gently pull one

of the fuse holder’s wires up and

pull the fuse off of both wire clips

inside the fuse holder.

• Do not write on either side of the

CD, particularly the non-label

side. (Signals are read from the

non-label side.)

• Keep the CD dry. A water drop

can act as a lens and affect the

laser beam’s focus.

• If you park your vehicle in the sun,

temperatures inside the vehicle

can easily reach levels that could

damage your CDs. To prevent

heat damage, avoid leaving your

CDs in your vehicle.

(illus - show yellow fuse holder)

3. To open the red power wire’s fuse

holder, push together and twist

the fuse holder’s parts until they

spring apart. Then remove the

fuse if it is blown.

If a CD skips when you try to play it, it

might be scratched. Your local Ra-

dioShack store sells a Scratch n Fix

kit (Cat. No. 42-127) that might help

remove the scratch and stop the skip.