NordicTrack Treadmill NTTL25513 User Manual

Patent Pending

Model No. NTTL25513

Serial No.

USER'S MANUAL

Find the serial number in the location

shown below. Write the serial number

in the space above for reference.

Serial Number Decal

QUESTIONS?

If you have questions, or if there

are missing parts, we will guar-

antee complete satisfaction

through direct assistance from

our factory.

TO AVOID DELAYS, PLEASE

CALL DIRECT TO OUR TOLL-

FREE CUSTOMER HOT LINE.

The trained technicians on our

Customer Hot Line will provide

immediate assistance, free of

charge to you.

CUSTOMER HOT LINE:

1-888-825-2588

Mon.–Fri., 6 a.m.–6 p.m. MST

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this man-

ual for future reference.

Visit our website at

www.nordictrack.com

new products, prizes,

fitness tips, and much more!

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT PRECAUTIONS

WARNING:

To reduce the risk of burns, fire, electric shock, or injury to persons, read the

following important precautions and information before operating the treadmill.

1. It is the responsibility of the owner to ensure

that all users of this treadmill are adequately

informed of all warnings and precautions.

12. Failure to use a properly functioning surge

suppressor could result in damage to the con-

trol system of the treadmill. If the control sys-

tem is damaged, the walking belt may change

speed or stop unexpectedly, which may result

in a fall and serious injury.

2. Use the treadmill only as described.

3. Place the treadmill on a level surface, with at

least eight feet of clearance behind it and two

feet on each side. Do not place the treadmill

on any surface that blocks air openings. To

13. Keep the power cord and the surge suppres-

sor away from heated surfaces.

protect the floor or carpet from damage, place 14. Never move the walking belt while the power

a mat under the treadmill.

is turned off. Do not operate the treadmill if

the power cord or plug is damaged, or if the

treadmill is not working properly. (See

BEFORE YOU BEGIN on page 5 if the tread-

mill is not working properly.)

4. Keep the treadmill indoors, away from mois-

ture and dust. Do not put the treadmill in a

garage or covered patio, or near water.

5. Do not operate the treadmill where aerosol

products are used or where oxygen is being

administered.

15. Never start the treadmill while you are stand-

ing on the walking belt. Always hold the

handrails while using the treadmill.

6. Keep children under the age of 12 and pets

away from the treadmill at all times.

16. The treadmill is capable of high speeds.

Adjust the speed in small increments to avoid

sudden jumps in speed.

7. The treadmill should not be used by persons

weighing more than 300 pounds.

17. The pulse sensor is not a medical device.

Various factors, including the user's move-

ment, may affect the accuracy of heart rate

readings. The pulse sensor is intended only

as an exercise aid in determining heart rate

trends in general.

8. Never allow more than one person on the

treadmill at a time.

9. Wear appropriate exercise clothes when

using the treadmill. Do not wear loose clothes

that could become caught in the treadmill.

Athletic support clothes are recommended for

both men and women. Always wear athletic

shoes. Never use the treadmill with bare feet,

wearing only stockings, or in sandals.

18. Using hand weights and not holding the

handrails may compromise your ability to

maintain your balance. Hand weights should

be used only by experienced users.

19. Never leave the treadmill unattended while it

is running. Always remove the key, unplug

the power cord and move the on/off switch to

the off position when the treadmill is not in

use. (See the drawing on page 5 for the loca-

tion of the on/off switch.)

10. When connecting the power cord (see page 8),

plug the power cord into a surge suppressor

(not included) and plug the surge suppressor

into a grounded circuit capable of carrying 15

or more amps. No other appliance should be on

the same circuit. Do not use an extension cord.

20. Do not attempt to raise, lower, or move the

treadmill until it is properly assembled. (See

ASSEMBLY on page 6, and HOW TO FOLD

AND MOVE THE TREADMILL on page 25.) You

must be able to safely lift 45 pounds (20 kg) in

order to raise, lower, or move the treadmill.

11. Use only a single-outlet surge suppressor that

meets all of the specifications described on

page 8. To purchase a surge suppressor, see

your local NordicTrack dealer or call 1-800-

806-3651 and order part number 146148.

Download from Www.Somanuals.com. All Manuals Search And Download.

21. Do not change the incline of the treadmill by

placing objects under the treadmill.

from your CD player or VCR when you are not

using them.

22. When folding or moving the treadmill, make

sure that the storage latch is fully closed.

26. Inspect and properly tighten all parts of the

treadmill regularly.

23. When using iFIT.com CD’s and videos, an

electronic “chirping” sound will alert you

when the speed and/or incline of the treadmill

is about to change. Always listen for the

“chirp” and be prepared for speed and/or in-

cline changes. In some instances, the speed

and/or incline may change before the per-

sonal trainer describes the change.

27. Never insert or drop any object into any

opening.

28.

DANGER:

Always unplug the power

cord immediately after use, before cleaning

the treadmill, and before performing the main-

tenance and adjustment procedures de-

scribed in this manual. Never remove the

motor hood unless instructed to do so by an

authorized service representative. Servicing

other than the procedures in this manual

should be performed by an authorized service

representative only.

24. When using iFIT.com CD’s and videos, you

can manually override the speed and incline

settings at any time by pressing the speed

and incline buttons. However, when the next

“chirp” is heard, the speed and/or incline will

change to the next settings of the CD or video 29. This treadmill is intended for in-home use

program.

only. Do not use this treadmill in any commer-

cial, rental, or institutional setting.

25. Always remove iFIT.com CD’s and videos

WARNING:

Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. ICON assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

SAVE THESE INSTRUCTIONS

The decal shown at the right has been placed on your treadmill. If the decal is miss-

ing or illegible, please call our Customer Service Department, toll-free, to order a free

replacement decal (see ORDERING REPLACEMENT PARTS on page 31). Apply the

decal in the location shown. Note: The decal is shown at 43% of actual size.

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE YOU BEGIN

Thank you for selecting the revolutionary NordicTrack^®

7100 R treadmill. The 7100 R treadmill offers an im-

pressive array of features to make your home work-

outs more enjoyable and effective. And when you’re

not exercising, the unique 7100 R can be folded up, re-

quiring less than half the floor space of other treadmills.

at 1-888-825-2588, Monday through Friday, 6 a.m.

until 6 p.m. Mountain Time (excluding holidays). To

help us assist you, please note the product model

number and serial number before calling. The model

number of the treadmill is NTTL25513. The serial num-

ber can be found on a decal attached to the treadmill

(see the front cover of this manual for the location).

For your benefit, read this manual carefully before

using the treadmill. If you have additional questions,

please call our Customer Service Department toll-free

Before reading further, please familiarize yourself with

the parts that are labeled in the drawing below.

Book Holder

Water Bottle Holder*

Hand Weight Holder

Console

Handrail

Pulse Sensor

Lock Knob

Key/Clip

LEFT SIDE

RIGHT SIDE

On/Off Switch

Circuit Breaker

Walking Belt

Foot Pad

Power Cord

Flexible Walking Platform

Rear Roller

Adjustment Bolts

*No water bottle is included.

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY

Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not

dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench

and your own flat-bladed screwdriver

and

adjustable wrench.

Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a

small amount of lubricant may be transferred to the top of the treadmill or the shipping carton. This is a normal

condition and does not affect treadmill performance. If there is lubricant on top of the walking belt or foot pads,

simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

1. Slide the treadmill out of the box. Insert the three Cage

Nuts (96) into the three indicated holes in the treadmill.

To insert each Cage Nut (96), first hook one side of the

Cage Nut into the hole and then use a flat-bladed screw-

driver to press the other side into the hole, as shown.

2. With the help of a second person, carefully raise both

Uprights (99) to a vertical position. Press the Lock Knob

Sleeve (111) into the left Upright.

Next, make sure that the Lock Pin Collar (109) and the

Spring (110) are on the Lock Pin (107). (Note: If there are

two Lock Pin Collars, place one on each side of the

Spring.) Insert the Lock Pin into the Lock Knob Sleeve

(111) and the Left Upright (99).

113

112

110

Press the Lock Knob Spacer (112) onto the left Upright

(99). Tighten the Lock Knob (113) onto the Lock Pin

(107).

107

111

109

3. With the help of a second person, carefully raise the

Walking Platform (24) to the storage position and make

sure that the lock pin is properly engaged as described

on page 25.

Position the Base Plate (91) on the treadmill as shown.

Attach the Base Plate with the three Base Plate Screws

(92). Note: It may be helpful if a second person tips the

treadmill slightly as you tighten the Screws.

Carefully lower the Walking Platform (24) to the floor as

described on page 25.

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Refer to drawing 4a. While another person holds the

Handrails (83), thread Handrail Bolts (104) about 2-3

turns into the indicated holes in each Handrail. Then, re-

move the Handrail Bolts.

Refer to drawing 4b. Pinch the tabs on the Grounding

Bracket (115) so that the tabs will fit into the indicated

hole in the left Upright (99). Then, insert the Grounding

Bracket into the hole as far as possible.

104

115

104

Note: It may be helpful to set the Handrails (83) on the

Uprights (99) and loosely thread a Handrail Bolt (104)

into the left Upright and the left Handrail. Tip the

Handrails, if necessary, to thread in the Bolt. Have an-

other person support the Handrails while you complete

the remaining steps.

5. Pull the Upright Wire Harness (119) up through a

Handrail Spacer (116). Place the Handrail Spacer on the

right Upright (99) as shown, with the cutout toward the

treadmill (refer to inset drawing A).

Cutout

116

Connect the Upright Wire Harness (119) to the wires ex-

tending from the Console Base (80). The connectors

should slide easily and “snap” into place. If the con-

nectors do not slide easily and snap into place, turn a

connector and try again. Insert the connectors and the

Upright Wire Harness into the hole in the Console Base

(see inset drawing B).

119

116

Set the Handrail (83) on the Handrail Spacer (116), being

careful not to pinch the Upright Wire Harness (119).

6. Insert two Handrail Bolts (104) with Handrail Washers

(105) and Handrail Bushings (106) into the right Upright

(99) and the right Handrail Spacer (116). Turn the

Handrail Bushings so they fit against the Upright (refer to

the inset drawing). Lift the right Handrail (83) slightly and

align the Bolts with the holes in the Handrail. Loosely

thread the Bolts into the Handrail. Do not tighten the

Bolts yet.

116

115

118

104

106

116

See the inset drawing. Remove the Handrail Bolt (104)

used in step 4. Place the other Handrail Spacer (116) on

the left Upright (99), with the cutout toward the treadmill.

Reach inside the left Upright and spread the tabs on the

Grounding Bracket (115) to allow a Bolt to pass through

the Grounding Bracket. Attach the left Handrail (83) as de-

scribed above. Make sure that the Handrail Bushings

(106) are turned properly and that the Bolt goes through

the Grounding Bracket. Tighten all four Handrail Bolts.

Press an Upright Endcap (118) into each Upright.

105

106

105

104

7. Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen

wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 27). To protect the

floor or carpet from damage, place a mat under the treadmill.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION AND ADJUSTMENT

THE PERFORMANT LUBE^TMWALKING BELT

an equipment-grounding conductor and a grounding

plug. Plug the power cord into a surge suppressor,

and plug the surge suppressor into an appropriate

outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Important: The treadmill is not compatible with

GFCI-equipped outlets.

Your treadmill features a walking belt coated with

PERFORMANT LUBE^TM, a high-performance lubricant.

IMPORTANT: Never apply silicone spray or other

substances to the walking belt or the walking plat-

form. Such substances will deteriorate the walking

belt and cause excessive wear.

This product is for use on a nominal 120-volt circuit,

and has a grounding plug that looks like the plug illus-

trated in drawing 1 below. A temporary adapter that

looks like the adapter illustrated in drawing 2 may be

used to connect the surge suppressor to a 2-pole

receptacle as shown in drawing 2 if a properly

grounded outlet is not available.

HOW TO PLUG IN THE POWER CORD

DANGER:

Improper connection

of the equipment-grounding conductor can

result in an increased risk of electric shock.

Check with a qualified electrician or service-

man if you are in doubt as to whether the

product is properly grounded. Do not modify

the plug provided with the product—if it will

not fit the outlet, have a proper outlet

Grounded Outlet Box

Surge Suppressor

Grounding Pin

installed by a qualified electrician.

Your treadmill, like any other type of sophisticated

electronic equipment, can be seriously damaged by

sudden voltage changes in your home’s power.

Voltage surges, spikes, and noise interference can

result from weather conditions or from other appliances

being turned on or off. To decrease the possibility of

your treadmill being damaged, always use a surge

suppressor with your treadmill (see drawing 1 at

the right). To purchase a surge suppressor, see

your local NordicTrack dealer or call 1-800-806-

3651 and order part number 146148.

Grounding Pin

Grounded Outlet

Grounding Plug

Grounded Outlet Box

Adapter

Surge Suppressor

Use only a single-outlet surge suppressor that is

UL 1449 listed as a transient voltage surge sup-

pressor (TVSS). The surge suppressor must have a

UL suppressed voltage rating of 400 volts or less

and a minimum surge dissipation of 450 joules.

The surge suppressor must be electrically rated

for 120 volts AC and 15 amps. There must be a

monitoring light on the surge suppressor to indi-

cate whether it is functioning properly. Failure to

use a properly functioning surge suppressor could

result in damage to the control system of the

treadmill. If the control system is damaged, the

walking belt may change speed or stop unexpect-

edly, which may result in a fall and serious injury.

Lug

Metal Screw

The temporary adapter should be used only until a

properly grounded outlet (drawing 1) can be installed

by a qualified electrician.

The green-colored rigid ear, lug, or the like extending

from the adapter must be connected to a permanent

ground such as a properly grounded outlet box cover.

Whenever the adapter is used it must be held in place

by a metal screw. Some 2-pole receptacle outlet box

covers are not grounded. Contact a qualified elec-

trician to determine if the outlet box cover is

grounded before using an adapter.

This product must be grounded. If it should malfunc-

tion or break down, grounding provides a path of least

resistance for electric current to reduce the risk of elec-

tric shock. This product is equipped with a cord having

Download from Www.Somanuals.com. All Manuals Search And Download.

Program

Display

Main

Display

Pulse

Sensor

Pulse

Sensor

Note: If there is a thin sheet

of clear plastic on the face

of the console, remove it.

Clip

Key

FEATURES OF THE CONSOLE

sonal trainer right in your home. Using the included

audio cable, you can connect the treadmill to your home

stereo, portable stereo, or computer and play special

iFIT.com CD programs (CD’s are available separately).

IFIT.com CD programs automatically control the speed

and incline of the treadmill as a personal trainer guides

you through every step of your workout. High-energy

music provides added motivation. Each CD features

two programs designed by certified personal trainers.

The advanced console offers a selection of features

designed to help you get the most from your exercise.

When the manual mode of the console is selected, the

speed and incline of the treadmill can be changed with

a touch of a button. As you exercise, the console will

provide continuous exercise feedback. You can even

measure your heart rate using the handgrip pulse sen-

sor. And for a total-body workout, the included hand

weights can be used as you walk on the treadmill.

In addition, you can connect the treadmill to your VCR

and TV and play iFIT.com video programs (videocas-

settes are available separately). Video programs offer

Twenty-seven preset workout programs are also offered. the same benefits as iFIT.com CD programs, but add

Each program automatically controls the speed and

incline of the treadmill to give you an effective workout.

You can even create custom workout programs and

store them in memory for future use.

the excitement of working out with a class and an in-

structor—the hottest new trend at health clubs.

With the treadmill connected to your computer, you

can also go to our Web site at www.iFIT.com and ac-

cess basic programs, audio programs, and video pro-

grams directly from the internet. Additional options are

soon to be available. See www.iFIT.com for details.

In addition, the console offers a fitness test program

that measures your relative fitness level, and a pulse-

driven program that automatically adjusts the speed

and incline of the treadmill to keep your heart rate near

a target level during your workout. Note: The fitness

test program and the pulse-driven program require the

use of an optional chest pulse sensor (see page 24).

To purchase additional iFIT.com CD’s or videocas-

settes, call toll-free 1-800-735-0768. For informa-

tion about an optional chest pulse sensor, see

page 24.

The console also features new iFIT.com interactive

technology. IFIT.com technology is like having a per-

Download from Www.Somanuals.com. All Manuals Search And Download.

Plug in the power cord.

CAUTION:

Before operating the

console, read the following precautions.

See HOW TO PLUG IN THE POWER CORD on

page 8.

• Do not stand on the walking belt when turn-

ing on the power.

Move the on/off switch to the on position.

• Always wear the clip (see the drawing below)

while operating the treadmill.

Locate the on/off switch

on the treadmill near the

power cord. Move the

Position

• Adjust the speed in small increments in

order to avoid sudden jumps in speed.

on/off switch to the on

position.

• The pulse sensor is not a medical device.

Various factors may affect the accuracy of

heart rate readings. The pulse sensor is in-

tended only as an exercise aid in determin-

ing heart rate trends in general.

Insert the key fully into the console.

Stand on the foot rails of the treadmill. Attach the

clip securely to the waistband of your clothes.

Next, insert the key into the console. After a

moment, various displays and indicators on the

console will light. Note: When the key is inserted,

the treadmill incline system may automatically

calibrate itself—the treadmill will rise to the highest

incline level and then return to the lowest incline

level. During calibration, the left side of the main

display will show two dashes (– –) and the time

indicator will flash.

• If you have heart problems, or if you are over

60 years of age and have been inactive, do

not use the pulse-driven program. If you are

taking medication regularly, consult your

physician to find whether the medication will

affect your exercise hart rate.

• Using hand weights and not holding the

handrails may compromise your ability to

maintain your balance. Hand weights should

be used only by experienced users.

Enter your weight.

Although you can use the console without entering

your weight, the console will count your calorie ex-

penditure more accurately if you enter your weight.

To enter your weight, press either of the Enter

Weight buttons. The words “ENTER WEIGHT” and

the current weight setting will appear in the main

• To reduce the possibility of electric shock,

keep the console dry. Avoid spilling liquids

on the console and place only a sealed water

bottle in the water bottle holder.

GETTING STARTED

Attach the clip to the waistband of your clothes.

Stand on the foot rails

of the treadmill. Find

display. Press the Enter Weight buttons again to

enter your weight. The buttons can be held down

to enter your weight quickly. Four seconds after

the buttons are last pressed, the weight setting will

disappear from the display. Your weight will then

be saved in memory.

the clip attached to the

key and slide the clip

onto the waistband of

your clothes. Next, in-

Clip

sert the key into the

console. Test the clip by carefully taking a few

steps backward until the key is pulled from the

console. If the key is not pulled from the con-

sole, adjust the position of the clip as needed.

Then, remove the key from the console.

To use the manual mode of the console, follow the

steps beginning on page 11. To use a preset program,

see page 12. To create and use a custom program,

see pages 14 and 15. To use the fitness test program,

see page 16. To use the pulse-driven program, see

page 17. To use an iFIT.com CD or video program,

refer to page 21. To use an iFIT.com program di-

rectly from our Web site, see page 23.

Download from Www.Somanuals.com. All Manuals Search And Download.

Follow your progress with the LED track, the

Training Zone display, and the main display.

HOW TO USE THE MANUAL MODE

The LED track—When

the manual mode or the

iFIT.com mode is se-

Insert the key fully into the console.

See GETTING STARTED on page 10.

lected, the program dis-

play will show an LED

track representing 1/4

mile. As you exercise, the indicators around the

track will light in sequence until you have walked or

run 1/4 mile. A new lap will then begin.

Select the manual mode.

When the key is inserted, the manual mode will

automatically be selected. If a program has been

selected, press the Select Workout Goal button

repeatedly until the words “MANUAL MODE”

appear in the main display.

The Training Zone

display—As you ex-

ercise, this display

will show the approxi-

mate intensity level of

your exercise. For ex-

ample, if seven to twelve indicators in the display

are lit, your intensity level is ideal for fat burning.

Press the Start button or the Speed + button to

start the walking belt.

The main display—The main display will show

the following information:

A moment after the button is pressed, the walking

belt will begin to move at 1 mph. Hold the handrails

and begin walking. As you exercise, change the

speed of the walking belt as desired by pressing

the Speed + and – but-

Incline—The left side of

the main display shows

the incline level of the

treadmill.

tons. Each time a but-

ton is pressed, the

speed setting will

Distance/Laps—The

change by 0.1 mph; if a

next section of the main

button is held down, the

display shows the dis-

speed setting will

tance that you have

walked and the number

of 1/4-mile laps you have

change in increments of 0.5 mph. To change the

speed setting quickly, press the 1-step Speed but-

tons. The speed range is 0.5 mph to 12 mph.

completed. The display will change from one num-

ber to the other every few seconds, as shown by

the indicators.

To stop the walking belt, press the Stop button.

The time will begin to flash in the main display. To

restart the walking belt, press the Start button or

the Speed + button.

Calories/Heart Rate—

When you are not using

the handgrip pulse sen-

sor, the center of the

main display will show

the approximate number

Note: During the first few minutes that the treadmill

is used, inspect the alignment of the walking belt

and align it if necessary (see page 27).

of calories you have burned. When you are using

the handgrip pulse sensor, the display will show

your heart rate (see step 6 on page 12).

Change the incline of the treadmill as desired.

To change the incline of

the treadmill, press the

Time/Pace—When the

manual mode or the

iFIT.com mode is se-

lected, the main display

will show the elapsed

time and your current

pace (pace is measured in minutes per mile). The

display will change from one number to the other

Incline

and

buttons.

Each time a button is

pressed, the incline will

change by 0.5%. To

change the incline quickly, press the 1-step Incline

buttons. The incline range is 0% to 12%. Note: After

the buttons are pressed, it may take a moment for

the treadmill to reach the selected incline setting.

Download from Www.Somanuals.com. All Manuals Search And Download.

as shown by the indicators. When a program is se-

lected, the display will show the time remaining in

the program, your current pace, and the time re-

maining in the current segment of the program.

Note: During the fitness test program, the display

will show the elapsed time, your current pace, and

the time remaining in the current segment of the

program.

When you are finished exercising, stop the

walking belt and remove the key.

Step onto the foot rails, press the Stop button, and

adjust the incline of the treadmill to the lowest level.

The incline must be at the lowest level when

the treadmill is raised to the storage position or

the treadmill will be damaged. Next, remove the

key from the console and put it in a secure place.

Note: If the displays and indicators on the con-

sole remain lit after the key is removed, the

console is in the “demo” mode. Refer to page

24 and turn off the demo mode.

Speed—The right side

of the main display

shows the speed of the

walking belt.

When you are finished using the treadmill, move

the on/off switch near the power cord to the off

position and unplug the power cord.

Note: The console can

display speed and dis-

tance in either miles or

kilometers. To find

which unit of measure-

HOW TO USE PRESET PROGRAMS

ment is selected, hold

down the Stop button while inserting the key into

the console. An “E” for English miles or an “M” for

metric kilometers will appear on the right side of

the main display. Press the Speed + button to

change the unit of measurement. When the de-

sired unit of measurement is selected, remove the

key and then reinsert it. Note: For simplicity, all

instructions in this manual refer to miles.

Insert the key fully into the console.

See GETTING STARTED on page 10.

Select the desired preset program.

The console offers twenty-seven preset programs—

nine programs that focus on weight loss, nine

programs designed for aerobic exercise, and nine

programs for high-performance conditioning.

To reset the main display, press the Stop button,

remove the key, and then reinsert the key.

When the key is inserted, the manual mode will

automatically be selected. To select one of the

preset programs, first press the Select Workout

Goal button repeatedly until the words “WEIGHT

LOSS,” “AEROBIC,” or “PERFORMANCE” appear

in the main display.

Measure your heart rate, if desired.

To measure your

heart rate, stand

on the foot rails

and place your

hands on the

metal contacts on

the handrail. Your

palms must be

resting on the

upper contacts,

and your fingers

must be touching

the lower con-

tacts—avoid moving your hands. When your

pulse is detected, the Heart Rate indicator will

flash, three dashes (– – –) will appear in the main

display, and then your heart rate will be shown.

For the most accurate heart rate reading, con-

tinue to hold the contacts for about 15 seconds.

Next, press the Select Course button repeatedly

to select one of the weight loss, aerobic, or perfor-

mance programs. For example, if the words

“WEIGHT LOSS” appear in the main display, you

can select the Riverside Trail, Mountain Trail,

Nature Path, Power Hike, Waterfall Canyon,

Moose Tracks, Boulder Trek, Evergreen Path, or

Meadow Trail program.

Download from Www.Somanuals.com. All Manuals Search And Download.

Three seconds after a preset program is selected,

the name of the selected program, the maximum

speed setting for the program, the maximum in-

cline setting for the program, and the total program

time will begin to scroll across the main display.

Note: Each time a segment ends and the speed

settings move to the left, if all of the indicators in

the Current Segment column are lit, the speed set-

tings may move downward so that only the highest

indicators in the columns will appear in the pro-

gram display. When the speed settings move to

the left again and not all of the indicators in the

Current Segment column are lit, the speed settings

will move back up.

The program dis-

play will show the

speed settings for

the program you

have selected.

If the speed or incline setting for the current

segment is too high or too low, you can manually

override the setting by pressing the Speed or

Incline buttons on the console. Every few times

one of the Speed buttons is pressed, an additional

indicator will light or darken in the Current Segment

column. If any of the columns to the right of the

Current Segment column have the same number

of lit indicators as the Current Segment column,

an additional indicator may light or darken in those

columns as well. Note: If you manually adjust the

speed setting so that all of the indicators in the

Current Segment column are lit, the speed settings

in the program display will not move downward as

described above. Note: If you manually override

the speed or incline setting for the current seg-

ment, when the segment ends the treadmill will

automatically adjust to the speed and incline

settings programmed for the next segment.

Press the Start button or the Speed + button to

start the program.

A moment after the button is pressed, the tread-

mill will automatically adjust to the first speed and

incline settings for the program. Hold the handrails

and begin walking.

Each program is divided into several time seg-

ments of different lengths. (The main display

shows both the time remaining in the program and

the time remaining in the current segment of the

program.) One speed setting and one incline set-

ting are programmed for each segment. The

speed setting for

the first segment

is shown in the

Current Segment

flashing Current

To stop the program temporarily, press the Stop

button. The time will begin to flash in the main dis-

play. To restart the program, press the Start button

or the Speed + button. To end the program, press

the Stop button, remove the key, and then reinsert

the key.

Segment column

of the program

display. (The in-

cline settings are

not shown in the program display.) The speed set-

tings for upcoming segments will be shown in the

columns to the right.

Follow your progress with the displays.

See step 5 on page 11.

When only three seconds remain in the first seg-

ment of the program, both the Current Segment

column and the column to the right will flash and a

tone will sound. In addition, if the speed and/or

the incline of the treadmill is about to change, the

speed setting and/or the incline setting will flash in

the main display to alert you, and three tones will

sound. When the first segment is completed, all

speed settings will move one column to the left.

The speed setting for the second segment will then

be shown in the flashing Current Segment column

and the treadmill will automatically adjust to the

speed and incline settings for the second segment.

Measure your heart rate if desired.

See step 6 on page 12.

When the program has ended, remove the key.

Step onto the foot rails and make sure that the in-

cline of the treadmill is at the lowest level. Next,

remove the key from the console and put it in a se-

cure place. Note: If the displays and indicators

on the console remain lit after the key is re-

moved, the console is in the “demo” mode.

Refer to page 24 and turn off the demo mode.

The program will continue in this way until the

speed setting for the last segment is shown in the

Current Segment column and no time remains in

the program. The walking belt will then slow to a

stop.

When you are finished using the treadmill, move

the on/off switch near the power cord to the off

position and unplug the power cord.

Download from Www.Somanuals.com. All Manuals Search And Download.

Refer to the program display. Each custom pro-

gram is divided into one-minute segments. One

speed setting and one incline setting can be pro-

grammed for each segment. The speed setting for

the first segment

HOW TO CREATE CUSTOM PROGRAMS

Insert the key fully into the console.

will be shown in the

See GETTING STARTED on page 10.

Current Segment

flashing Current

Segment column of

the program dis-

play. (The incline

settings are not

Select one of the custom programs.

When the key is inserted, the manual mode will

automatically be selected. To select one of the

custom programs, first press the Select Workout

Goal button repeatedly until the letters “CUSTOM

PROG” appear in the main display.

shown in the pro-

gram display.) To program a speed setting and an

incline setting for the first segment, simply adjust

the speed and incline of the treadmill as desired

by pressing the Speed and Incline buttons. Every

few times one of the Speed buttons is pressed, an

additional indicator will light or darken in the

Current Segment column.

When the first segment of the program is com-

pleted, the current speed setting and the current

incline setting will be stored in memory. The three

columns of indicators will then move one column

to the left, and the speed setting for the second

segment will be shown in the flashing Current

Segment column. Program a speed setting and an

incline setting for the second segment as de-

scribed above. Note: After the third segment is

completed, the columns of indicators in the pro-

gram display will no longer move to the left.

Instead, each time a segment is completed, the

flashing Current Segment column will move one

column to the right. If the Current Segment col-

umn reaches the right side of the program display,

when the current segment is completed all

columns of indicators in the program display will

move three columns to the left.

Next, press the Select Course button repeatedly to

select the Learn 1 or Learn 2 program.

Three seconds after a custom program is selected,

the name of the selected program and the total

program time will begin to scroll across the main

display.

Note: If the custom program has not yet been

defined, three columns of indicators will be lit

in the program display. If more than three

columns of indicators are lit, refer to HOW TO

USE CUSTOM PROGRAMS on page 15.

Continue programming speed and incline settings

for as many segments as desired; custom pro-

grams can have up to forty segments. When you

are finished with your workout, press the Stop but-

ton twice. The speed and incline settings that you

programmed and the number of segments that you

programmed will then be saved in memory.

Press the Start button or the Speed + button

and program the desired speed and incline

settings.

A moment after the button is pressed, the walking

belt will begin to move. Hold the handrails and

begin walking.

When the program has ended, remove the key.

See step 6 on page 13.

Download from Www.Somanuals.com. All Manuals Search And Download.

column and the column to the right will flash, a se-

ries of tones will sound, the speed setting and the

incline setting will flash in the main display, and all

speed settings will move one column to the left.

The speed setting for the second segment will then

be shown in the flashing Current Segment column

and the treadmill will automatically adjust to the

second speed and incline settings that you pro-

grammed previously.

HOW TO USE CUSTOM PROGRAMS

Insert the key fully into the console.

See GETTING STARTED on page 10.

Select one of the custom programs.

When the key is inserted, the manual mode will

automatically be selected. To select one of the

custom programs, first press the Select Workout

Goal button repeatedly until the letters “CUSTOM

PROG” appear in the main display. Next, press the

Select Course button repeatedly to select the Learn

1 or Learn 2 program.

The program will continue until the speed setting

for the last segment is shown in the Current

Segment column and no time remains in the pro-

gram. The walking belt will then slow to a stop.

If desired, you can redefine the program while

using it. To change the speed or incline setting

during the current segment, simply press the

Speed or Incline buttons. When the current segment

is completed, the new setting will be saved in mem-

ory. To increase the length of the program, first

wait until the program is completed. Then, press the

Start button and program speed and incline settings

for as many additional segments as desired. (Note:

While you are adding segments to the program,

the speed settings in the program display will not

move to the left. Instead, each time a segment is

completed, the flashing Current Segment column

will move one column to the right. If the Current

Segment column reaches the right side of the pro-

gram display, when the current segment is com-

pleted all columns of indicators in the program dis-

play will move three columns to the left.) When

you have added as many segments as desired,

press the Stop button twice. To decrease the

length of the program, press the Stop button twice

at any time before the program is completed.

Three seconds after a custom program is se-

lected, the name of the selected program and the

total program time will begin to scroll across the

main display.

The program display will show the first speed set-

tings for the program you have selected (refer to

the drawing below). Note: If only three columns

of indicators are lit in the program display,

refer to HOW TO CREATE A CUSTOM PRO-

GRAM on page 14.

Press the Start button or the Speed + button to

start the program.

A moment after the button is pressed, the tread-

mill will automatically adjust to the first speed and

incline settings that you programmed previously.

Hold the handrails and begin walking.

Each program is divided into several one-minute

segments. (The main display shows both the time

remaining in the program and the time remaining

in the current segment of the program.) One

speed setting and one incline setting are pro-

grammed for each

To stop the program temporarily, press the Stop

button. The time will begin to flash in the main dis-

play. To restart the program, press the Start but-

ton or the Speed + button. To end the program,

press the Stop button, remove the key, and then

reinsert the key.

segment. The

Current Segment

speed setting for

Follow your progress with the displays.

See step 5 on page 11.

the first segment

will be shown in

the flashing

Current Segment

Measure your heart rate, if desired.

See step 6 on page 12.

column of the pro-

gram display. (The incline settings are not shown

in the program display.) The speed settings for the

next several segments will be shown in the

columns to the right.

When the program has ended, remove the key.

See step 6 on page 13.

When only three seconds remain in the first seg-

ment of the program, both the Current Segment

Download from Www.Somanuals.com. All Manuals Search And Download.

If you have already entered your age, go to step 5.

If you have not entered your age, press the Enter

Age buttons to enter your age. The buttons can be

held down to enter your age quickly. Once you

have entered your age, it will be saved in memory.

HOW TO USE THE FITNESS TEST PROGRAM

The fitness test program is designed to measure your

relative fitness level. For the best results, the fitness

test program should be used at a time when your en-

ergy level is high; the fitness test program should not

be used if you have already exercised during the day.

Note: You must wear the optional chest pulse sen-

sor to use the fitness test program (see page 24).

Follow the steps below to use the fitness test program.

Press the Start button or the Speed + button to

start the program.

When the button is

pressed, the main dis-

play will show an “L 1”

Put on the chest pulse sensor.

(level 1), indicating that

the first four-minute level

of the fitness test pro-

gram has begun. The incline of the treadmill will

automatically adjust to 3% and the walking belt

will begin to move at 1.5 mph. Hold the handrails

and begin walking.

To put on the chest pulse sensor, refer to the in-

structions included with the chest pulse sensor.

Insert the key fully into the console.

See GETTING STARTED on page 10.

The fitness test program is divided into seven,

four-minute levels. Each level consists of four,

one-minute segments. One speed setting and one

incline setting are

Select the fitness test program.

When the key is inserted, the manual mode will

automatically be selected. To select the fitness

test program, first press the Select Workout Goal

button repeatedly until the words “HEART RATE”

appear in the main display.

programmed for

each segment. The

Current Segment

speed setting for

the first segment

will be shown in the

flashing Current

Segment column of

the program display. (The incline settings are not

shown in the program display.) The speed settings

for the next thirteen segments will be shown in the

thirteen columns to the right.

Next, press the Select Course button repeatedly

until the words “FITNESS TEST” appear.

When only three seconds remain in the first one-

minute segment of the program, both the Current

Segment column and the column to the right will

flash, a tone will sound, and all speed settings will

move one column to the left. The speed setting for

the second segment will then be shown in the

flashing Current Segment column.

When the fitness test program is selected, the

program display will show the first twenty-seven

speed settings for the program.

When the first four-minute level of the program is

completed, both the Current Segment column and

the column to the right will flash, a series of tones

will sound, the speed setting and/or the incline

setting will flash in the main display, and all speed

settings will move one column to the left. The

main display will then show an “L 2,” indicating

that the second four-minute level has begun. The

incline will then adjust to 4% and the speed will in-

crease to 2.5 mph.

Enter your age.

Three seconds after the fitness test program is se-

lected, the words “ENTER AGE” and the current

age setting will appear in the main display. You

must enter your age to use the fitness test program.

Download from Www.Somanuals.com. All Manuals Search And Download.

At the beginning of each four-minute level, the

speed and/or the incline of the treadmill will auto-

matically increase. The fitness test program will

continue in this way until your heart rate reaches

70% of your estimated maximum heart rate, and

the current four-minute level is completed. The fit-

ness test program will then be completed, regard-

less of how many levels remain.

HOW TO USE THE PULSE-DRIVEN PROGRAM

The pulse-driven program automatically adjusts the

speed and incline of the treadmill to keep your heart

rate near a target level during your workout. Note: You

must wear the optional chest pulse sensor to use

the pulse-driven program (see page 24).

When the fitness test

program is completed,

the letter “C” will appear

in the main display and

a two-minute cool-down

period will begun. The

CAUTION:

If you have heart prob-

lems, or if you are over 60 years of age and

have been inactive, do not use the pulse-driven

program. If you are taking medication regularly,

consult your physician to find whether the

medication will affect your exercise heart rate.

incline will then adjust to 1% and the speed will de-

crease.

When the cool-down period is completed, the

walking belt will slow to a stop. After the fitness

test program is com-

pleted, your fitness

level will be shown in

Follow the steps below to use the pulse-driven program.

Put on the chest pulse sensor.

To put on the chest pulse sensor, refer to the in-

structions included with the chest pulse sensor.

the main display. There

are ten fitness levels;

fitness level 10 (FL:10)

is the highest. Remem-

ber, the fitness program is intended only to indi-

cate your relative fitness level.

Insert the key fully into the console.

See GETTING STARTED on page 10.

Select the pulse-driven program.

Note: The Speed and Incline buttons will not

function while the fitness test program is selected. If

your pulse is not detected during the program, the

letters “PLS” will flash in the main display. If your

pulse is not detected during the last thirty seconds

of any four-minute level (after four minutes, after

eight minutes, etc.), the fitness test program will

end and the main display will show a fitness level

of 0 (FL: 0).

When the key is inserted, the manual mode will

automatically be selected. To select the pulse-

driven program, first press the Select Workout

Goal button repeatedly until the words “HEART

RATE” appear in the main display.

The fitness test program cannot be stopped tem-

porarily and then restarted. However, the program

can be stopped at any time by pressing the Stop

button. The main display will then show an esti-

mated fitness level.

Next, press the Select Course button until the words

“PULSE DRIVEN” appear.

When the program has ended, remove the key.

See step 6 on page 13.

Download from Www.Somanuals.com. All Manuals Search And Download.

play. When the first segment is completed, all

heart rate settings will move one column to the

left. The heart rate setting for the second segment

will then be shown in the flashing Current

Segment column, and the speed and/or the incline

of the treadmill will change, if needed, to bring

your heart rate closer to the heart rate setting for

the second segment.

Enter your age.

Three seconds after the pulse-driven program is

selected, the words “ENTER AGE” and the current

age setting will appear in the main display. You

must enter your age to use the pulse-driven program.

The program will continue until the target heart

rate setting for the last segment is shown in the

Current Segment column and no time remains in

the program. The walking belt will then slow to a

stop.

If you have already entered your age, go to step 5.

If you have not entered your age, press the Enter

Age buttons to enter your age. The buttons can be

held down to enter your age quickly. Once you

have entered your age, it will be saved in memory.

If the speed or incline setting for the current seg-

ment is too high or too low, you can adjust the set-

ting with the Speed or Incline buttons. However, if

you decrease the speed, the incline will automati-

cally increase; if you increase the speed, the in-

cline will decrease. If you increase the incline, the

speed will decrease; if you decrease the incline,

the speed will increase. The treadmill will always

attempt to keep your heart rate near the target

heart rate setting for the current segment. Note:

When the incline reaches the lowest setting, the

speed cannot be increased any further. When the

incline reaches the highest setting, the speed can-

not be decreased any further.

Press the Start button or the Speed + button to

start the program.

A moment after the button is pressed, the tread-

mill will automatically adjust to the first speed and

incline settings for the program. Hold the handrails

and begin walking.

The pulse-driven program is divided into several

time segments of different lengths. (The main dis-

play shows both the time remaining in the program

and the time remaining in the current segment of

the program.) One target heart rate setting is pro-

grammed for each

If your pulse is not detected during the program,

the letters “PLS” will flash in the main display and

the speed and incline of the treadmill may auto-

matically decrease until your pulse is detected. If

this occurs, refer to the instructions included with

the optional chest pulse sensor.

segment. The tar-

get heart rate set-

Current Segment

ting for the first

segment will be

shown in the flash-

ing Current

Segment column of

The pulse-driven program cannot be stopped tem-

porarily and then restarted. However, the program

can be stopped at any time with the Stop button.

the program display. The target heart rate settings

for the next twenty-two segments will be shown in

the columns to the right.

Follow your progress with the displays.

Refer to step 5 on page 11.

When only three seconds remain in the first seg-

ment of the program, both the Current Segment

column and the column to the right will flash, a se-

ries of tones will sound, and the speed setting

and/or the incline setting will flash in the main dis-

When the program has ended, remove the key.

See step 6 on page 13.

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO CONNECT YOUR PORTABLE STEREO

HOW TO CONNECT THE TREADMILL TO YOUR

CD PLAYER, VCR, OR COMPUTER

Note: If your stereo has an RCA-type AUDIO OUT

jack, see instruction A below. If your stereo has a

3.5mm LINE OUT jack, see instruction B. If your

stereo has only a PHONES jack, see instruction C.

To use iFIT.com CD’s, the treadmill must be connected

to your portable CD player, portable stereo, home

stereo, or computer with CD player. See this page and

page 20 for connecting instructions. To use iFIT.com

videocassettes, the treadmill must be connected to

your VCR. See page 21 for connecting instructions. To

use iFIT.com programs directly from our Web site,

the treadmill must be connected to your home com-

puter. See page 20 for connecting instructions.

A. Plug one end of the audio cable into the jack on the

front of the treadmill near the power cord. Plug the

other end of the cable into the included adapter. Plug

the adapter into an AUDIO OUT jack on your stereo.

HOW TO CONNECT YOUR PORTABLE CD PLAYER

AUDIO OUT

RIGHT

LEFT

Note: If your CD player has separate LINE OUT and

PHONES jacks, see instruction A below. If your CD

player has only one jack, see instruction B.

Audio

Cable

Adapter

A. Plug one end of the audio cable into the jack on the

front of the treadmill near the power cord. Plug the

other end of the cable into the LINE OUT jack on

your CD player. Plug your headphones into the

PHONES jack.

B. Plug one end of the audio cable into the jack on the

front of the treadmill near the power cord. Plug the

other end of the cable into the LINE OUT jack on

your stereo.

PHONES LINE OUT

LINE OUT

PHONES

Head-

phones

Audio

Cable

LINE OUT

Audio

Cable

B. Plug one end of the audio cable into the jack on the

front of the treadmill near the power cord. Plug the

other end of the cable into a 3.5mm Y-adapter

(available at electronics stores). Plug the Y-adapter

into the PHONES jack on your CD player. Plug your

headphones into the other side of the Y-adapter.

C. Plug one end of the audio cable into the jack on the

front of the treadmill near the power cord. Plug the

other end of the cable into a 3.5mm Y-adapter

(available at electronics stores). Plug the Y-adapter

into the PHONES jack on your stereo. Plug your

headphones into the other side of the Y-adapter.

PHONES

3.5mm

Y-adapter

PHONES

Audio

Cable

3.5mm

Y-adapter

Audio

Cable

Headphones

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO CONNECT YOUR HOME STEREO

HOW TO CONNECT YOUR COMPUTER

Note: If your stereo has an unused LINE OUT jack,

see instruction A below. If the LINE OUT jack is

being used, see instruction B.

Note: If your computer has a 3.5mm LINE OUT jack,

see instruction A. If your computer has only a

PHONES jack, see instruction B.

A. Plug one end of the audio cable into the jack on the

front of the treadmill near the power cord. Plug the

other end of the cable into the included adapter.

Plug the adapter into the LINE OUT jack on your

stereo.

A. Plug one end of the audio cable into the jack on the

front of the treadmill near the power cord. Plug the

other end of the cable into the LINE OUT jack on

your computer.

LINE OUT

VCR

Amp

LINE OUT

Audio

Cable

LINE OUT

Audio

Cable

Adapter

B. Plug one end of the audio cable into the jack on the

front of the treadmill near the power cord. Plug the

other end of the cable into a 3.5mm Y-adapter

(available at electronics stores). Plug the Y-adapter

into the PHONES jack on your computer. Plug your

headphones or speakers into the other side of the

Y-adapter.

B. Plug one end of the audio cable into the jack on the

front of the treadmill near the power cord. Plug the

other end of the cable into the included adapter.

Plug the adapter into an RCA Y-adapter (available

at electronics stores). Next, remove the wire that is

currently plugged into the LINE OUT jack on your

stereo and plug the wire into the unused side of the

Y-adapter. Plug the Y-adapter into the LINE OUT

jack on your stereo.

PHONES

Audio

Cable

3.5mm

Y-adapter

VCR

Amp

LINE OUT

Headphones/Speakers

RCA

Y-adapter

Audio

Adapter

Cable

Wire removed from

LINE OUT jack

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO CONNECT YOUR VCR

HOW TO USE IFIT.COM CD AND VIDEO

PROGRAMS

Note: If your VCR has an unused AUDIO OUT jack,

see instruction A below. If the AUDIO OUT jack is

being used, see instruction B. If you have a TV

with a built-in VCR, see instruction B. If your VCR

is connected to your home stereo, see HOW TO

CONNECT YOUR HOME STEREO on page 20.

To use iFIT.com CD’s or videocassettes, the treadmill

must be connected to your portable CD player, portable

stereo, home stereo, computer with CD player, or

VCR. See HOW TO CONNECT THE TREADMILL TO

YOUR CD PLAYER, VCR, OR COMPUTER on page

19. Note: To purchase iFIT.com CD’s or videocas-

settes, call toll-free 1-800-735-0768.

A. Plug one end of the audio cable into the jack on the

front of the treadmill near the power cord. Plug the

other end of the cable into the included adapter.

Plug the adapter into the AUDIO OUT jack on your

VCR.

Follow the steps below to use an iFIT.com CD or video

program.

Insert the key fully into the console.

ANT IN

VIDEO AUDIO

RF OUT

OUT

See GETTING STARTED on page 10.

AUDIO OUT

RIGHT

LEFT

Select the iFIT.com mode.

Audio

Cable

Adapter

When the key is in-

serted, the manual

mode will automatically

be selected. To use an

iFIT.com CD or video

program, press the

iFIT.com button. The indicator beside the button will

light.

B. Plug one end of the audio cable into the jack on the

front of the treadmill near the power cord. Plug the

other end of the cable into the included adapter.

Plug the adapter into an RCA Y-adapter (available

at electronics stores). Next, remove the wire that is

currently plugged into the AUDIO OUT jack on your

VCR and plug the wire into the unused side of the

Y-adapter. Plug the Y-adapter into the AUDIO OUT

jack on your VCR.

Insert the iFIT.com CD or videocassette.

If you are using an iFIT.com CD, insert the CD

into your CD player. If you are using an iFIT.com

videocassette, insert the videocassette into your

VCR.

Press the PLAY button on your CD player or

VCR.

ANT IN

VIDEO AUDIO

RF OUT

OUT

A moment after the button is pressed, your per-

sonal trainer will begin guiding you through your

workout. Simply follow your personal trainer’s

instructions. Note: If the time is flashing in the

main display, press the Start button or the Speed

+ button on the console. The treadmill will not re-

spond to a CD or video program when the time is

flashing.

RCA

Y-adapter

Audio

Cable

Adapter

Wire removed from

AUDIO OUT jack

During the CD or video program, an electronic

“chirping” sound will alert you when the speed

and/or incline of the treadmill is about to change.

CAUTION: Always listen for the “chirp” and be

prepared for speed and/or incline changes. In

some instances, the speed and/or incline may

change before the personal trainer describes

the change.

Download from Www.Somanuals.com. All Manuals Search And Download.

If the speed or incline settings are too high or too

low, you can manually override the settings at any

time by pressing the Speed or Incline buttons on

the console. However, when the next “chirp” is

heard, the speed and/or incline will change to

the next settings of the CD or video program.

• Adjust the volume of your CD player or VCR.

If the volume is too high or too low, the con-

sole may not detect the program signals.

• Make sure that the audio cable is properly

connected, that it is fully plugged in, and that

it is not wrapped around a power cord.

To stop the walking belt at any time, press the

Stop button on the console. The time will begin to

flash in the main display. To restart the program,

press the Start button or the Speed + button. After

a moment, the walking belt will begin to move.

When the next “chirp” is heard, the speed and

incline will change to the next settings of the

CD or video program.

• If you are using your portable CD player and

the CD skips, set the CD player on the floor or

another flat surface instead of on the console.

Follow your progress with the LED track and

the displays.

See step 5 on page 11.

When the CD or video program is completed, the

walking belt will stop and the time will begin to flash

in the main display. Note: To use another CD or

video program, press the Stop button or remove

the key and go to step 1 on page 21.

Measure your heart rate, if desired.

Refer to step 6 on page 12.

When the program is completed, remove the

key.

Note: If the speed or incline of the treadmill

does not change when a “chirp” is heard:

See step 6 on page 13.

• Make sure that the iFIT.com indicator is lit and

that the time is not flashing in the main dis-

play. If the time is flashing, press the Start

button or the Speed + button on the console.

Download from Www.Somanuals.com. All Manuals Search And Download.

Return to the treadmill and stand on the foot

rails. Find the clip attached to the key and slide

the clip onto the waistband of your clothes.

HOW TO USE PROGRAMS DIRECTLY FROM

OUR WEB SITE

When the on-screen countdown ends, the program

will begin and the walking belt will begin to move.

Hold the handrails, step onto the walking belt, and

begin walking. During the program, an electronic

“chirping” sound will alert you when the speed

and/or incline of the treadmill is about to change.

CAUTION: Always listen for the “chirp” and be

prepared for speed and/or incline changes.

Our Web site at www.iFIT.com allows you to access

basic programs, audio programs, and video programs

directly from the internet. Additional options are soon

to be available. See www.iFIT.com for details.

To use programs from our Web site, the treadmill must

be connected to your home computer. See HOW TO

CONNECT YOUR COMPUTER on page 20. In

addition, you must have an internet connection and

an internet service provider. A list of specific system

requirements will be found on our Web site.

If the speed or incline settings are too high or too

low, you can manually override the settings at any

time by pressing the Speed or Incline buttons on

the console. However, when the next “chirp” is

heard, the speed and/or incline will change to

the next settings for the program.

Follow the steps below to use a program from our

Web site.

Insert the key fully into the console.

To stop the walking belt at any time, press the

Stop button on the console. The time will begin to

flash in the main display. To restart the program,

press the Start button or the Speed + button. After

a moment, the walking belt will begin to move at 1

mph. When the next “chirp” is heard, the speed

and incline will change to the next settings of

the program.

See GETTING STARTED on page 10.

Select the iFIT.com mode.

When the key is in-

serted, the manual

mode will automatically

be selected. To use a

program from our Web

When the program is completed, the walking belt

will stop and the time will begin to flash in the main

display. Note: To use another program, press the

Stop button and go to step 5.

site, press the iFIT.com

button. The indicator beside the button will light.

Go to your computer and start an internet

connection.

Note: If the speed or incline of the treadmill

does not change when a “chirp” is heard, make

sure that the iFIT.com indicator is lit and that

the Time display is not flashing. In addition,

make sure that the audio cable is properly con-

nected, that it is fully plugged in, and that it is

not wrapped around a power cord.

Start your web browser, if necessary, and go to

our Web site at www.iFIT.com.

Follow the desired links on our Web site to se-

lect a program.

Follow your progress with the LED track and

the displays.

Read and follow the on-line instructions for using a

program.

See step 5 on page 11.

Follow the on-line instructions to start the

program.

When the program has ended, remove the key.

See step 6 on page 13.

When you start the program, an on-screen count-

down will begin.

Download from Www.Somanuals.com. All Manuals Search And Download.

THE INFORMATION MODE/DEMO MODE

THE OPTIONAL CHEST PULSE SENSOR

The console features an information mode that keeps

track of the total number of hours that the treadmill has

been operated and the total number of miles that the

walking belt has moved. The information mode also

allows you to switch the console from miles per hour to

kilometers per hour. In addition, the information mode

allows you to turn on and turn off the demo mode.

An optional chest pulse sensor adds even more

features to the console. The chest pulse sensor provides

hands-free operation and continuously monitors your

heart rate during your workouts. To purchase the

optional chest pulse sensor, call toll-free 1-800-

734-2377.

To select the information mode, hold down the Stop

button while inserting the key into the console. When

the information mode is selected, the main display will

show the following information:

The right side of the main

display will show the total

number of hours that the

treadmill has been used.

The left side of the main

display will show the total

number of miles that the

walking belt has moved.

An “E” for English miles or

an “M” for metric kilometers

will appear on the right side

of the main display. Press

the Speed + button to

change the unit of measure-

ment.

IMPORTANT: Make sure

that there is not a letter

“D” in the main display. If

a “D” appears in the display,

the console is in the “demo”

mode. This mode is intended

to be used only when a treadmill is displayed in a store.

When the console is in the demo mode, the power cord

can be plugged in, the key can be removed from the

console, and the displays and indicators on the console

will automatically light in a preset sequence, although

the buttons on the console will not operate. If a “D” ap-

pears in the display when the information mode is

selected, press the Speed – button so the display is

blank.

To exit the information mode, remove the key from the

console.

Download from Www.Somanuals.com. All Manuals Search And Download.

HOW TO FOLD AND MOVE THE TREADMILL

HOW TO FOLD THE TREADMILL FOR STORAGE

Before folding the treadmill, adjust the incline to the

lowest position. If this is not done, the treadmill may be per-

manently damaged. Remove the key and unplug the power

cord. CAUTION: You must be able to safely lift 45 pounds

(20 kg) in order to raise, lower, or move the treadmill.

1. Hold the treadmill with your hands in the locations shown

at the right. CAUTION: To decrease the possibility of in-

jury, bend your legs and keep your back straight. As

you raise the treadmill, make sure to lift with your legs

rather than your back. Raise the treadmill about halfway

to the vertical position.

2. Move your right hand to the position shown and hold the

treadmill firmly. Pull the lock knob to the left and hold it.

Raise the treadmill until the indicated plate is past with

the lock pin. Release the lock knob. Make sure that the

plate is resting against the lock pin as shown.

Lock Pin

To protect the floor or carpet from damage, place a

mat under the treadmill. Keep the treadmill out of

direct sunlight. Do not leave the treadmill in the stor-

age position in temperatures above 85° Fahrenheit.

Lock

Knob

Plate

HOW TO MOVE THE TREADMILL

Before moving the treadmill, convert the treadmill to the stor-

age position as described above. Make sure that the plate

is resting against the lock pin.

1. Hold the handrails as shown and place one foot against a

wheel.

2. Tilt the treadmill back until it rolls freely on the front wheels.

Carefully move the treadmill to the desired location.

Never move the treadmill without tipping it back. To

reduce the risk of injury, use extreme caution while

moving the treadmill. Do not attempt to move the

treadmill over an uneven surface.

3. Place one foot on the base, and carefully lower the tread-

mill until it is resting in the storage position.

Base

Front Wheels

HOW TO LOWER THE TREADMILL FOR USE

1. Refer to drawing 2 above. Hold the upper end of the treadmill with your right hand as shown. Pull the lock knob

to the left and hold it. Pivot the treadmill down until the frame is past the lock pin.

2. Refer to drawing 1 above. Hold the treadmill firmly with both hands, and lower the treadmill to the floor.

CAUTION: To decrease the possibility of injury, bend your legs and keep your back straight.

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and

follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-

free at 1-888-825-2588, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).

PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 8). Use only a single-outlet surge suppressor

that meets all of the specifications described on page 8. Important: The treadmill is not compatible

with GFCI-equipped outlets.

b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.

c. Check the circuit breaker located on the treadmill

near the power cord. If the switch protrudes as

shown, the circuit breaker has tripped. To reset the

circuit breaker, wait for five minutes and then press

the switch back in.

Tripped

Reset

d. Check the on/off switch located on the treadmill near

the power cord. The switch must be in the on position.

Position

PROBLEM: The power turns off during use

SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see c. above). If the

circuit breaker has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for

five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key fully into the console.

d. Make sure that the on/off switch is in the on position.

e. If the treadmill still will not run, please call our Customer Service Department, toll-free.

PROBLEM: The displays of the console do not function properly

SOLUTION: a. Remove the key from the console and unplug the

power cord. Remove the indicated Screws (48) from

the Hood (62). Carefully rotate and lift the Hood.

Locate the Reed Switch (37) and the Magnet (31) on

the left side of the Pulley (30). Turn the Pulley until

the Magnet is aligned with the Reed Switch. Make

sure that the gap between the Magnet and the

Reed Switch is about 1/8”. If necessary, loosen the

Screw (93) and move the Reed Switch slightly.

Retighten the Screw. Re-attach the hood, and run the

treadmill for a few minutes to check for a correct

speed reading.

1/8”

Top

View

Download from Www.Somanuals.com. All Manuals Search And Download.

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 8.

b. If the walking belt is overtightened, treadmill perfor-

mance may decrease and the walking belt may be-

come damaged. Remove the key and UNPLUG THE

POWER CORD. Using the allen wrench, turn both

rear roller adjustment bolts counterclockwise, 1/4 of a

3”–4”

turn. When the walking belt is properly tightened, you

should be able to lift each side of the walking belt 3 to

4 inches off the walking platform. Be careful to keep

the walking belt centered. Plug in the power cord, in-

sert the key and run the treadmill for a few minutes.

Repeat until the walking belt is properly tightened.

Rear Roller Adjustment Bolts

c. If the walking belt still slows when walked on, please call our Customer Service Department, toll-

free.

PROBLEM: The walking belt is off-center or slips when walked on

SOLUTION: a. If the walking belt is off-center, first remove the key and

UNPLUG THE POWER CORD. If the walking belt has

shifted to the left, use the allen wrench to turn the left

rear roller bolt clockwise 1/2 of a turn; if the walking belt

has shifted to the right, turn the bolt counterclockwise

1/2 of a turn. Be careful not to overtighten the walking

belt. Plug in the power cord, insert the key and run the

treadmill for a few minutes. Repeat until the walking belt is

centered.

b. If the walking belt slips when walked on, first remove the

key and UNPLUG THE POWER CORD. Using the allen

wrench, turn both rear roller bolts clockwise, 1/4 of a turn.

When the walking belt is correctly tightened, you should

be able to lift each side of the walking belt 3 to 4 inches

off the walking platform. Be careful to keep the walking

belt centered. Plug in the power cord, insert the key and

carefully walk on the treadmill for a few minutes. Repeat

until the walking belt is properly tightened.

PROBLEM: The incline of the treadmill does not change correctly or does not change when iFIT.com

CD’s and videos are played

SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-

move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the

maximum incline level and then return to the minimum level. This will recalibrate the incline system.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONDITIONING GUIDELINES

During the first few minutes of exercise, your body

uses easily accessible carbohydrate calories for en-

ergy. Only after the first few minutes does your body

begin to use stored fat calories for energy. If your goal

is to burn fat, adjust the speed and incline of the tread-

mill until your heart rate is near the lowest number in

your training zone.

WARNING:

Before beginning this

or any exercise program, consult your physi-

cian. This is especially important for individu-

als over the age of 35 or individuals with pre-

existing health problems.

The pulse sensor is not a medical device.

Various factors, including your movement,

may affect the accuracy of heart rate readings.

The sensor is intended only as an exercise aid

in determining heart rate trends in general.

For maximum fat burning, adjust the speed and incline

of the treadmill until your heart rate is near the middle

number in your training zone.

Aerobic Exercise

If your goal is to strengthen your cardiovascular sys-

tem, your exercise must be “aerobic.” Aerobic exercise

is activity that requires large amounts of oxygen for

prolonged periods of time. This increases the demand

on the heart to pump blood to the muscles, and on the

lungs to oxygenate the blood. For aerobic exercise,

adjust the speed and incline of the treadmill until your

heart rate is near the highest number in your training

zone.

The following guidelines will help you to plan your ex-

ercise program. For more detailed exercise informa-

tion, obtain a reputable book or consult your physician.

EXERCISE INTENSITY

Whether your goal is to burn fat or to strengthen your

cardiovascular system, the key to achieving the

desired results is to exercise with the proper intensity.

The proper intensity level can be found by using your

heart rate as a guide. The chart below shows recom-

mended heart rates for fat burning and aerobic exercise.

WORKOUT GUIDELINES

Each workout should include the following three parts:

A Warm-up—Start each workout with 5 to 10 minutes

of stretching and light exercise. A proper warm-up in-

creases your body temperature, heart rate and circula-

tion in preparation for exercise.

Training Zone Exercise—After warming up, increase

the intensity of your exercise until your pulse is in your

training zone for 20 to 60 minutes. (During the first few

weeks of your exercise program, do not keep your

pulse in your training zone for longer than 20 minutes.)

Breathe regularly and deeply as you exercise—never

hold your breath.

To find the proper heart rate for you, first find your age

near the bottom of the chart (ages are rounded off to

the nearest ten years). Next, find the three numbers

above your age. The three numbers define your “train-

ing zone.” The lower two numbers are recommended

heart rates for fat burning; the higher number is the

recommended heart rate for aerobic exercise.

A Cool-down—Finish each workout with 5 to 10 min-

utes of stretching to cool down. This will increase the

flexibility of your muscles and will help prevent post-ex-

ercise problems.

To measure your heart rate during exercise, use the

pulse sensor on the console. If your heart rate is too

high or too low, adjust the speed and incline of the

treadmill.

EXERCISE FREQUENCY

To maintain or improve your condition, complete three

workouts each week, with at least one day of rest be-

tween workouts. After a few months, you may com-

plete up to five workouts each week if desired. The key

to success is to make exercise a regular and enjoyable

part of your everyday life.

Fat Burning

To burn fat effectively, you must exercise at a relatively

low intensity level for a sustained period of time.

Download from Www.Somanuals.com. All Manuals Search And Download.

SUGGESTED STRETCHES

The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.

1. Toe Touch Stretch

Stand with your knees bent slightly and slowly bend forward

from your hips. Allow your back and shoulders to relax as you

reach down toward your toes as far as possible. Hold for 15

counts, then relax. Repeat 3 times. Stretches: Hamstrings, back

of knees and back.

2. Hamstring Stretch

Sit with one leg extended. Bring the sole of the opposite foot to-

ward you and rest it against the inner thigh of your extended leg.

Reach toward your toes as far as possible. Hold for 15 counts,

then relax. Repeat 3 times for each leg. Stretches: Hamstrings,

lower back and groin.

3. Calf/Achilles Stretch

With one leg in front of the other, reach forward and place your

hands against a wall. Keep your back leg straight and your back

foot flat on the floor. Bend your front leg, lean forward and move

your hips toward the wall. Hold for 15 counts, then relax. Repeat

3 times for each leg. To cause further stretching of the achilles

tendons, bend your back leg as well. Stretches: Calves, achilles

tendons and ankles.

4. Quadriceps Stretch

With one hand against a wall for balance, reach back and grasp

one foot with your other hand. Bring your heel as close to your

buttocks as possible. Hold for 15 counts, then relax. Repeat 3

times for each leg. Stretches: Quadriceps and hip muscles.

5. Inner Thigh Stretch

Sit with the soles of your feet together and your knees outward.

Pull your feet toward your groin area as far as possible. Hold for

15 counts, then relax. Repeat 3 times. Stretches: Quadriceps

and hip muscles.

Download from Www.Somanuals.com. All Manuals Search And Download.

PART LIST—Model No. NTTL25513

R0303A

To locate the parts listed below, refer to the EXPLODED DRAWING attached in the center of this manual.

Key No. Qty.

Description

Key No. Qty.

Description

Allen Wrench

Wheel Bolt

100

Incline Motor Bolt (Bottom)

Incline Motor Bracket

Front Roller Adj. Bolt

Ground Wire Screw

Motor Bolt

Rear Endcap (Left)

Roller Adj. Washer

Rear Roller Adj. Washer

Rear Wheel

Front Wheel Nut/Frame Pivot Nut

Endcap Screw

Roller Guard (Left)

Roller Guard (Right)

Rear Endcap (Right)

Endcap Nut

Endcap Washer

Rear Roller

Warning Decal

Latch Plate

Wire Track Screw

Belt Guide

Front Endcap (Left)

Frame Pivot Bolt

Frame Pivot Washer

Foot Grip (Left)

Walking Belt

Walking Platform

Foot Grip (Right)

Front Endcap (Right)

Ground Wire

Support Bracket Screw

Support Bracket

Front Roller/Pulley

Magnet

Motor Belt

Motor

Frame Pivot Bushing

Frame Pivot Spacer

Reed Switch Clip

Reed Switch

Idler Assembly

Idler Pulley Bolt

Pulley Bushing

Idler Pulley

Lift Motor Nut/Idler Nut

Tension Washer

Incline Motor Bolt (Top)

Idler Arm Bearing

Idler Arm

Filter Wire

Lift Leg

Plastic Stand-Off

Power Supply

Power Supply Bracket

Releaseable Tie

Motor Hood

38*

Hood Clip

Controller

Controller Bracket

Motor Controller Wire

Power Cord

Power Cord Grommet

Circuit Breaker

12” Audio Wire

Audio Wire Nut

On/Off Switch

Static Decal

Belly Pan

Catch Screw

Belly Pan Bracket

Belly Pan Bracket Screw

Cable Tie

8” Cable Tie

Console Base

Console

Book Holder

Handrail

Handrail Endcap

Hand Grip Pulse

Grip Pulse Screw

Short Console Screw

Long Console Screw

Console Back

Base Plate Bumper

Base Plate

Base Plate Screw

Base Screw

Wire Track

Base Pad

Cage Nut

Upright Endcap

Key/Clip

Upright

Idler Spring

Hood Mount Screw

Hood Mount

Incline Motor

Front Wheel Bolt

Download from Www.Somanuals.com. All Manuals Search And Download.

Key No. Qty.

Description

Key No. Qty.

Description

101

102

103

104

105

106

107

108

109

110

111

112

113

114*

115

116

117

Front Wheel Bushing

Front Wheel

Front Wheel Spacer

Handrail Bolt

Handrail Washer

Handrail Bushing

Lock Pin

118

119

120

121

122

123

Upright Endcap (Round)

Wire Harness

Hood Mount (Side)

Console Ground Wire

iFIT.com Audio Cable

Jack

8” Blue Wire, M/F

8” Blue Wire, 2F

Pin Clip

Lock Pin Collar

Lock Knob Spring

Lock Knob Sleeve

Lock Knob Spacer

Lock Knob

Latch Assembly

Grounding Bracket

Handrail Spacer

Hand Weights

12” Green Wire, F/Ring

10” Green Wire, 2 Ring

26” White Wire, 2F

20” White Wire, M/F

4” Black Wire, 2F

User's Manual

* Includes all parts shown in the box

# These parts are not illustrated

ORDERING REPLACEMENT PARTS

To order replacement parts, call our Customer Service Department toll-free at 1-888-825-2588, Monday through

Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give

the following information:

• The MODEL NUMBER OF THE PRODUCT (NTTL25513)

• The NAME OF THE PRODUCT (NordicTrack^®7100 R treadmill)

• The SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual)

• The KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the PART LIST on pages 30 and 31 and the

EXPLODED DRAWING attached in the center of this manual)

Download from Www.Somanuals.com. All Manuals Search And Download.

EXPLODED DRAWING—Model No. NTTL25513

R0303A

To identify the parts shown on this exploded drawing, refer to

the PART LIST on pages 30 and 31 of the USER’S MANUAL.

Download from Www.Somanuals.com. All Manuals Search And Download.

EXPLODED DRAWING—Model No. NTTL25513

R0303A

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

WHAT IS COVERED—The entire NordicTrack^®7100 R treadmill (“Product”) is warranted to be free of all defects in ma-

terial and workmanship.

WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.

HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the motor for three years after the date

of purchase. The belt and deck are covered for two years after the date of purchase. All mechanical components are

covered for two years after the date of purchase. All electrical components are covered for two years after the date of

purchase. Labor is covered for one year. The hood, covers, belly pan, and decals are covered for six months after the

date of purchase.

WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or

component, providing the repairs are authorized by ICON first and are performed by an ICON trained and authorized

service provider, or, at our option, we will replace the Product.

WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, im-

proper assembly or installation, alterations, modifications without our written authorization or by failure on your part to

use, operate, and maintain as set out in your User’s Manual (“Manual”). This warranty does not extend to products used

for commercial or rental purposes or to products used as store display modules.

WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the

Product as specified in the Manual; notify our Customer Service Department of any defect within 10 days after discov-

ery of the defect; as instructed, return any defected part for replacement or, if necessary, the entire product, for repair.

USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product.

Remember to do the periodic maintenance requirements specified in the Manual to assure proper operation and your

continued satisfaction.

HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-888-825-2588 and tell them

your name and address and the serial number of your Product. They will tell you how to get a part replaced, or if neces-

sary, arrange for service where your Product is located or advise you how to ship the Product for service. Before ship-

ping, always obtain a Return Authorization Number (RA No.) from our Customer Service Department; securely pack

your Product (save the original shipping carton if possible); put the RA No. on the outside of the carton and insure the

product. Include a letter explaining the product or problem and a copy of your proof of purchase if you believe the ser-

vice is covered by warranty.

ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the

use or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or

profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature.

Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above lim-

itation may not apply to you.

The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability

or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not

allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.

No one is authorized to change, modify or extend the terms of this limited warranty.

This warranty gives you specific legal rights and you may have other rights which vary from state to state.

ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813

Part No. 183102 R0303A

Download from Www.Somanuals.com. All Manuals Search And Download.

MTD Tiller 390 Shown User Manual
Novatel Stereo System 600 G User Manual
Omnimount TV Video Accessories 303 User Manual
Optimus Microcassette Recorder 14 1121 User Manual
Oregon Scientific Clock Radio RM103A User Manual
Palsonic CRT Television 3435TS User Manual
Panasonic Answering Machine kx t1450 User Manual
Panasonic Cordless Telephone KX TPA50 User Manual
Panasonic Headphones KX TD1232CE User Manual
Panasonic Telephone KX G2200A User Manual