Model No. NTL19806.3
Serial No.
USER'S MANUAL
Write the serial number in the space
above for reference.
Serial Number Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete cus-
tomer satisfaction. If you have
questions, or if parts are missing,
PLEASE DO NOT CONTACT THE
STORE; please contact
Customer Care.
IMPORTANT: You must note the
product model number and
serial number (see the drawing
above) before contacting us:
CALL TOLL-FREE:
1-888-825-2588
Mon.–Fri. 6 a.m.–6 p.m. MST
Sat. 8 a.m.–4 p.m. MST
ON THE WEB:
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and in-
structions in this manual and all warnings on your treadmill before using your treadmill. ICON as-
sumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for persons over the age of 35 or per-
sons with pre-existing health problems.
more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
12. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 13. To purchase a surge suppressor, see
your local NORDICTRACK dealer or call the
telephone number on the front cover of this
manual and order part number 146148, or see
your local electronics store.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
13. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
5. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
14. Keep the power cord and the surge suppres-
sor away from heated surfaces.
15. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
TROUBLESHOOTING on page 26 if the tread-
mill is not working properly.)
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under the age of 12 and pets
away from the treadmill at all times.
16. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 15).
8. The treadmill should not be used by persons
weighing more than 350 lbs. (159 kg).
9. Never allow more than one person on the
treadmill at a time.
17. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
19. The pulse sensors are not medical devices.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensors are intended
only as exercise aids in determining heart
rate trends in general.
11. When connecting the power cord (see page 13),
plug the power cord into a surge suppressor
(not included). Plug the surge suppressor into
a grounded circuit capable of carrying 15 or
3
Download from Www.Somanuals.com. All Manuals Search And Download.
20. Never leave the treadmill unattended while it
is running. Always remove the key, unplug the
power cord, and switch the reset/off circuit
breaker to the “off” position when the tread-
mill is not in use. (See the drawing on page 6
tenna discharge unit, size of grounding con-
ductors, location of antenna discharge unit,
connection to grounding electrodes, and re-
quirements for the grounding electrode.
for the location of the reset/off circuit breaker.) 29. An outside antenna system should not be lo-
cated in the vicinity of overhead power lines
21. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 7, and HOW TO FOLD
AND MOVE THE TREADMILL on page 25.) You
must be able to safely lift 45 lbs. (20 kg) to
raise, lower, or move the treadmill.
or other electric light or power circuits, or
where it can fall into such power lines or cir-
cuits. When installing an outside antenna sys-
tem, extreme care should be taken to keep
from touching such power lines or circuits, as
contact with them might be fatal.
22. Do not change the incline of the treadmill by
placing objects under the treadmill.
30. To reduce the risk of electric shock, do not re-
move the cover or the back of the television.
There are no user serviceable parts inside.
Refer servicing to qualified service personnel.
23. When folding or moving the treadmill, make
sure that the frame is held securely in the
storage position.
31. Upon completion of any service or repairs to
the treadmill or the television, ask the service
technician to perform safety checks to con-
firm that the unit is in proper operating con-
dition.
24. Inspect and properly tighten all parts of the
treadmill regularly.
25. Never insert or drop any object into any
opening on the treadmill.
2
• Use No. 10 AWG (5.3mm ) copper, No. 8
2
AWG (8.4mm ) aluminum, No. 17 AWG
2
26.
DANGER:
Always unplug the power
(1.0mm ) copper-clad steel or bronze wire,
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
or larger as a ground wire.
• Secure an antenna lead-in and ground wires
to the house with stand-off insulators
spaced from 4 to 6 feet (1.22 to 1.83m)
apart.
• Mount an antenna discharge unit as close
as possible to where the lead-in enters the
house.
27. The treadmill is intended for in-home use
only. Do not use the treadmill in any commer-
cial, rental, or institutional setting.
• Use a jumper wire not smaller than No. 6
AWG (13.3mm ) copper, or the equivalent
when a separate antenna-grounding elec-
trode is used. See NEC Section 810-21 (j).
2
28. If an outside antenna or cable system is con-
nected, be sure that the antenna or cable sys-
tem is grounded to provide some protection
against voltage surges and built-up static
charges. Section 810 of the National
Note to CATV system installer: This reminder is
provided to call the CATV system installer’s at-
tention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particu-
lar, specifies that the cable ground shall be con-
nected to the grounding system of the building,
as close to the point of cable entry as practical.
Electrical Code, ANSI/NFPA No. 70-1984, pro-
vides information with respect to proper
grounding of the mast and supporting struc-
ture, grounding of the lead-in wire to an an-
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Lines
Ground
Clamp
Standoff
Insulators
Service
Entrance
Conductors
Mast
To External Antenna
Terminal of Treadmill
Antenna
Lead-in Wire
Service
Entrance
Equipment
Ground
Wire
Antenna
Discharge Unit
Ground Wire
Ground
Power Service Grounding
Electrode System (e.g.
Interior Metal Water Pipe)
Ground
Clamps
Bonding
Jumper
Clamps
Optional Antenna Grounding Electrode Driven 8
Feet (2.44m) Into The Earth (If Required By Local
Codes). See NEC Section 810–21 (f).
SAVE THESE INSTRUCTIONS
5
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the revolutionary NORDIC-
TRACK® ELITE 4200 treadmill. The ELITE 4200 tread-
mill offers an impressive selection of features designed
to make your workouts at home more enjoyable and
effective. And when you’re not exercising, the unique
ELITE 4200 treadmill can be folded up, requiring less
than half the floor space of other treadmills.
ing this manual, please see the front cover of this man-
ual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Fan
Personal Television/Console
Accessory Tray
Book Holder
Handrail
Key/Clip
Pulse Sensor
Reset/Off
Circuit Breaker
Walking Belt
Foot Rail
Power Cord
Platform Cushion
Rear Roller
Adjustment Bolts
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to
the top of the walking belt or the shipping carton. This is a normal condition and does not affect treadmill perfor-
mance. If there is lubricant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild,
non-abrasive cleaner.
Assembly requires the included hex key and your own Phillips screwdriver
.
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: If a part is not in the parts bag, check to see if it is preattached to
one of the parts to be assembled. To avoid damaging plastic parts, do not use power tools for assembly.
Extra hardware may be included.
3/4" Screw (4)–4
Star Washer
(90)–10
Handrail Bolt (64)–6
Upright Bolt (72)–4
1. Make sure that the power cord is unplugged.
1
With the help of a second person, raise the front
of the treadmill and insert the crossbar on the
Base (83) into the cutout in the cardboard stand
as shown. Have the second person hold the
treadmill to prevent it from moving forward
or backward until assembly step 2 is com-
pleted.
83
Cardboard
Stand
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Identify the Left Upright (73) and the Right
Upright (74). Hold the Right Upright near the
Right Base Cover (77) as shown. Insert the
Upright Wire Harness (75) up through the rec-
tangular hole in the bottom of the Right Upright
and out of the top of the Right Upright.
2
97
49
Gently pull up on the Upright Wire Harness (75)
as you set the Right Upright (74) on the Base
(83) inside the Right Base Cover (77). Be care-
ful not to pinch the Upright Wire Harness.
75
73
74
Attach the Right Upright (74) to the Base (83)
with two Upright Bolts (72) and two Star
76
Washers (90). Note: It may be necessary to tip
the tops of the Uprights forward slightly as you
thread the Upright Bolts (72) into the Uprights.
77
83
Hold Left Upright (73) near the Left Base Cover
(76), and insert the TV Cable (49) and the AV
Wire (97) up through the rectangular hole in the
bottom of the Left Upright and out of the top of
the Left Upright. Attach the Left Upright to the
Base (83) with two Upright Bolts and two Star
Washers (not shown).
90
72
With the help of a second person, lower the
treadmill off the cardboard stand.
3. Identify the Right Upright Sleeve (96) and the
Left Upright Sleeve (95). Slide the Right Upright
Sleeve onto the Right Upright (74), and slide the
Left Upright Sleeve onto the Left Upright (73).
3
95
73
“Left”
“Right”
96
74
8
Download from Www.Somanuals.com. All Manuals Search And Download.
4. With the help of a second person, hold the con-
sole assembly near the Uprights (73, 74).
4
Console
Assembly
Connect the Upright Wire Harness (75) to the
Console Wire Harness (71). See the inset draw-
ing). The connectors should slide together
easily and snap into place. If they do not, turn
one connector and try again. IF THE CONNEC-
TORS ARE NOT CONNECTED PROPERLY,
THE CONSOLE MAY BE DAMAGED WHEN
THE POWER IS TURNED ON.
73
71
75
74
75
71
5. Connect the TV Cable (49) and the AV Wire (97)
to the cables extending from the console assem-
bly. Then, insert the connectors down into the
Uprights (73, 74).
5
99
Next, insert the brackets on the Handrails (99)
into the Right Upright (74) and the Left Upright
(73). Make sure that no wires are pinched.
49
97
99
73
74
6. Finger tighten three Handrail Bolts (64) with
three Star Washers (90) into the Right Upright
(74). Next, finger tighten three Handrail Bolts
with three Star Washers (not shown) into the
Left Upright (73). Then, firmly tighten the six
Handrail Bolts.
6
73
64
90
74
90
64
9
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Slide the Right Upright Sleeve (96) up against
the console assembly. Attach the Right Upright
Sleeve with two 3/4" Screws (4).
7
Attach the Left Upright Sleeve (not shown) to the
Left Upright (73) as described above.
73
4
96
4
74
8. Note the location of the 75 ohm antenna terminal
and the audio/video input jack on the treadmill.
For the television to operate, the included
8
Audio/
Video
Input
Jack
Audio/Video Wire Harness (115) and your DVD
player or VCR must be connected to the
audio/video input jack on the treadmill, a personal
audio/video player must be connected to the
audio/video jack on the console, or an antenna, a
CATV cable, or a VCR must be connected to the
75 ohm antenna terminal (see page 11).
75 Ohm
Antenna
Terminal
115
9. Make sure that all parts are properly tightened before you use the treadmill. Keep the included hex key
in a secure place; the hex key is used to adjust the walking belt (see page 27). To protect the floor or carpet
from damage, place a mat under the treadmill.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Before operating the television, you must connect an antenna, a 75 ohm CATV cable, or a VCR to the 75
ohm antenna terminal on the treadmill; a VCR or DVD player to the three audio/video RCA jacks; or a per-
sonal audio/video player to the audio/video jack below the television on the console. Note: No antenna,
cable, or adapter is included.
HOW TO CONNECT AN ANTENNA
Indoor Antenna
300 Ohm Flat Wire
1. See the drawing near the bottom of this page.
Connect the 300 ohm flat wire from the antenna to a
300 ohm to 75 ohm adapter.
1. Place a VHF
antenna in the
desired loca-
tion. Connect
the 300 ohm
flat wire from
the antenna to
a 300 ohm to
75 ohm
Screwdriver
VHF 300
2. Push the 300 ohm to 75 ohm adapter onto the 75
ohm antenna terminal on the treadmill frame near
the power cord.
Ohm Flat
Wire
75 Ohm CATV Cable
1. See the drawing near the bottom of this page.
Connect the 75 ohm CATV cable from the antenna
to the 75 ohm antenna terminal on the treadmill
frame near the power cord.
adapter.
300 to 75 Ohm Adapter
2. Push the 300
ohm to 75 ohm
adapter onto
HOW TO CONNECT A 75 OHM CATV CABLE
VHF
Antenna
1. Connect a 75 ohm
the 75 ohm an-
tenna terminal
on the treadmill
frame near the
power cord.
CATV cable to the 75
ohm antenna terminal
on the treadmill frame
near the power cord.
75 Ohm CATV Cable
75 Ohm Terminal
300 to 75 Ohm
Adapter
75 Ohm
Terminal
HOW TO CONNECT A VCR
Outdoor Antenna
1. Connect one end of a 75 ohm CATV cable to the
video output jack on your VCR.
Note: Outdoor antennas are subject to weathering that
can reduce signal quality. Inspect your antenna and
the lead-in wiring before connecting the antenna.
2. Plug in the power cord of your VCR. See your VCR
user’s manual for proper grounding instructions.
3. Connect the 75 ohm CATV cable to the 75 ohm an-
tenna terminal on the treadmill frame near the power
cord.
Combination
VHF/UHF Antennas
300 Ohm
Flat Wire
HOW TO CONNECT A DVD PLAYER OR VCR
Plug the three-pronged end of the included audio/video
wire harness into your DVD player or VCR, and plug
the other end into the audio/video input jack on the
treadmill frame near the power cord.
75 Ohm
Terminal
75 Ohm
CATV Cable
HOW TO CONNECT A PERSONAL AUDIO/VIDEO
PLAYER DIRECTLY TO THE CONSOLE
300 to 75
Ohm Adapter
75 Ohm CATV Cable
Locate the audio/video jack below the television on the
console, and plug it into a jack on your MP3 player, CD
player, or personal audio/video player.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE CHEST PULSE SENSOR
HOW TO PUT ON THE CHEST PULSE SENSOR
• Store the chest pulse sensor in a warm, dry place.
Do not store the chest pulse sensor in a plastic bag
or other container that may trap moisture.
The chest pulse sensor consists of two components—
the chest strap and the sensor unit.
• Do not expose the chest pulse sensor to direct
sunlight for extended periods of time; do not expose
it to temperatures above 122° F (50° C) or below 14°
F (-10° C).
Chest Strap
Tabs
• Do not excessively bend or stretch the sensor unit
when using or storing the chest pulse sensor.
Tab
• Clean the sensor unit using a damp cloth—never
use alcohol, abrasives, or chemicals. The chest
strap may be hand washed and air dried.
Sensor
Buckle
Sensor Unit
Unit
CHEST PULSE SENSOR TROUBLESHOOTING
The instructions on the following pages explain
how the chest pulse sensor is used with the con-
sole. If the chest pulse sensor does not function
properly, try the steps below.
Insert the tab on one end of the chest strap into the
hole in one end of the sensor unit, as shown in the inset
drawing above. The tab should be flush with the front of
the sensor unit.
• Make sure that you are wearing the chest pulse sen-
sor as described at the left. Note: If the chest pulse
sensor does not function when positioned as de-
scribed, move it slightly lower or higher on your chest.
Next, wrap the chest
pulse sensor around
your chest and attach
the other end of the
chest strap to the
sensor unit. Adjust
the length of the
chest strap, if neces-
• Use saline solution such as saliva or contact lens
solution to wet the two electrode areas on the
sensor unit. If heart rate readings do not appear until
you begin perspiring, rewet the electrode areas.
sary. The chest pulse
sensor should be under your clothes, tight against your
skin, and as high under the pectoral muscles or
breasts as is comfortable. Make sure that the logo on
the sensor unit is facing forward and is right-side-up.
• As you walk or run on the treadmill, position your-
self near the center of the walking belt. For the
console to display heart rate readings, the user
must be within arm’s length of the console.
Pull the sensor unit away from your body a few inches
and locate the two electrode areas on the inner side
(the electrode areas are covered by shallow ridges).
Using saline solution such as saliva or contact lens so-
lution, wet both electrode areas. Return the sensor unit
to a position against your chest.
• The chest pulse sensor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical
conditions such as premature ventricular contrac-
tions (pvcs), tachycardia bursts, and arrhythmia.
• The operation of the chest pulse sensor can be
affected by magnetic interference caused by high
power lines or other sources. If it is suspected that
this is a problem, try relocating the treadmill.
CHEST PULSE SENSOR CARE AND MAINTENANCE
• Thoroughly dry the chest pulse sensor after each
use. The chest pulse sensor is activated when the
electrode areas are wetted and the heart rate
monitor is put on; the chest pulse sensor shuts off
when it is removed and the electrode areas are
dried. If the chest pulse sensor is not dried after
each use, it may remain activated longer than nec-
essary, draining the battery prematurely.
• The CR2032 battery may need to be replaced (see
page 28).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local NORDICTRACK dealer or call the tele-
phone number on the front cover of this manual
and order part number 146148, or see your local
electronics store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate, or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
FEATURES OF THE CONSOLE
The console also offers four heart rate programs that
control the speed and incline of the treadmill to help
you keep your heart rate near target heart rate settings.
The treadmill console offers an impressive array of
features designed to make your workouts more effec-
tive and enjoyable. When the manual mode of the con-
sole is selected, the speed and incline of the treadmill
can be changed with the touch of a button. As you ex-
ercise, the screen will display continuous exercise
feedback. You can even measure your heart rate using
the handgrip pulse sensor or the chest pulse sensor.
Whether you select the manual mode or a program,
you can enjoy the shows of your choice on the per-
sonal television while you get in shape. You can even
listen to your favorite workout music or audio books with
the console’s premium stereo sound system.
To turn on the power, follow the steps on page 15. To
use the manual mode, see page 15. To use an event
training program, see page 17. To use a preset pro-
gram, see page 18. To create and use a custom
program, see pages 19 and 20. To use a heart rate
program, see page 21. To operate the personal
television, see page 22. To use the stereo sound
system, see page 22. To use the information mode,
see page 23.
The console also offers four event training programs.
Each program counts down the distance as you com-
plete a 5 kilometer, 10 kilometer, half marathon, or full
marathon run.
In addition, the console features twenty-three preset
programs—eight Aerobic Fitness programs, seven
Performance programs, and eight Weight Loss pro-
grams. Each program automatically controls the speed
and incline of the treadmill as it guides you through an
effective workout. You can even create your own cus-
tom programs and save them for future use.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
HOW TO USE THE MANUAL MODE
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room tem-
perature before turning on the power. If you do not
do this, the console displays or other electrical
components may become damaged.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER to the left.
Select the manual mode.
2
Plug in the power cord (see
page 13). Next, locate the
Each time the key is inserted, the manual mode
will be selected. If you have selected a program,
press any of the program buttons (Event Training,
Aerobic Fitness, Performance, Custom, Heart
Rate Control, or Weight Loss) repeatedly until a
track and the word “Manual” appears on the
screen.
Reset
reset/off circuit breaker on
the treadmill frame near the
power cord. Switch the cir-
cuit breaker to the reset po-
sition.
Position
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is dis-
played in a store. If the displays light as soon as
you plug in the power cord and switch the circuit
breaker to the reset position, the demo mode is
turned on. To turn off the demo mode, hold down
the Stop button for a few seconds. If the displays
remain lit, see THE INFORMATION MODE on page
23 to turn off the demo mode.
Start the walking belt and adjust the speed.
3
To start the walking belt, press the Start button,
the Speed increase button, or one of the num-
bered speed (MPH) buttons.
If the Start button or the Speed increase button is
pressed, the walking belt will begin to move at 1
mph. As you exercise, change the speed of the
walking belt as desired by pressing the Speed in-
crease and decrease buttons. Each time a button
is pressed, the speed setting will change by 0.1
mph; if you keep your finger on the button, the
speed setting will change in increments of 0.5
mph. If one of the numbered speed (MPH) buttons
is pressed, the walking belt will gradually increase
in speed until it reaches the selected speed set-
ting.
Next, stand on the foot
rails of the treadmill.
Find the clip attached to
the key (see the drawing
to the right) and slide
the clip onto the waist-
band of your clothes.
Then, insert the key into
Clip
Key
the console. After a moment, the displays will light. IM-
PORTANT: In an emergency situation, the key can
be pulled from the console, causing the walking
belt to slow to a stop. Test the clip by carefully tak-
ing a few steps backward; if the key is not pulled
from the console, adjust the position of the clip.
To stop the walking belt, press the Stop button. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the numbered
speed (MPH) buttons.
Change the incline of the treadmill as desired.
Note: If there is a sheet of clear plastic on the face
of the console, remove the plastic. To prevent dam-
age to the walking platform, wear clean athletic
shoes while using the treadmill. The first time you
use the treadmill, observe the alignment of the
walking belt, and center the walking belt if neces-
sary (see page 27).
4
To change the incline of the treadmill, press the
Incline increase and decrease buttons or one of
the numbered incline (% GRADE) buttons.
Each time the Incline increase or decrease button
is pressed, the incline will change by 0.5%. If one
of the numbered incline (% GRADE) buttons is
pressed, the incline will gradually increase until it
reaches the selected incline setting.
Note: The console can display speed and distance in
either miles or kilometers. To find out which unit of
measurement is selected or to change the unit of mea-
surement, see THE INFORMATION MODE on page
23. For simplicity, all instructions in this section refer to
miles.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Select a display mode and follow your
progress with the exercise information on the
screen.
Measure your heart rate if desired.
5
6
You can measure your heart rate using either the
chest pulse sensor (see page 12) or the handgrip
pulse sensor. Note: If you use the handgrip pulse
sensor and the chest pulse sensor at the same
time, the display will not show your heart rate ac-
curately.
As you walk or run on the treadmill, the screen can
display the following exercise information:
•
The elapsed time. Note: When a program is
selected, the screen will show the time remain-
ing in the program instead of the elapsed time.
Before using
the handgrip
pulse sensor,
remove the
sheets of
•
The distance that you have walked or run.
Note: The console can display distance and
speed in either miles or kilometers (see HOW
TO USE THE INFORMATION MODE on page
23). For simplicity, all instructions in this
section refer to miles.
clear plastic
from the
metal con-
tacts. In addi-
tion, make
Contacts
•
•
The speed of the walking belt.
sure that
your hands are clean.
The approximate number of calories you have
burned.
To measure your heart rate, stand on the foot
rails and hold the metal contacts—avoid moving
your hands. When your pulse is detected, your
heart rate will appear on the screen. For the most
accurate heart rate reading, continue to hold
the contacts for about 15 seconds.
•
•
•
The incline level of the treadmill. Note: The in-
cline level of the treadmill will be displayed only
when you press the Incline buttons.
Your heart rate. Note: Your heart rate will be
displayed only when you use the handgrip
pulse sensor or the chest pulse sensor.
Turn on the fan if desired.
7
8
When the manual mode is selected, the screen
can show a track that represents 1/4 mile (400
meters). As you walk or run on the treadmill,
the indicators around the track will appear in
succession until the entire track appears. The
track will then disappear and the indicators will
again begin to appear in succession.
The fan features high and low speed settings.
Press the Fan button repeatedly to select a fan
speed or to turn off the fan. Note: If the fan is on
when the walking belt is stopped, the fan will turn
off automatically after a few minutes.
When you are finished exercising, remove the
key from the console.
While the television is off, you can select either of
two display modes—a track and some of the exer-
cise information, or all of the exercise information.
While the television is on, you can select any of
three display modes—the information can be dis-
played on the right side of the screen, on the bot-
tom of the screen, or the information can be turned
off while you watch the television. Press the
Display button repeatedly to select the desired dis-
play mode.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when you fold the treadmill to the storage posi-
tion or you may damage the treadmill. Next, re-
move the key from the console and put it in a se-
cure place.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. Important: If you do not
do this, the electrical components of the tread-
mill may wear prematurely.
To reset the console, press the Stop button, re-
move the key, and then reinsert the key.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop the program at any time, press the Stop
button. To restart the program, press the Start but-
ton. The walking belt will begin to move at 1 mph.
Adjust the speed of the walking belt as desired by
pressing the Speed increase or decrease button or
one of the numbered speed (MPH) buttons.
HOW TO USE AN EVENT TRAINING PROGRAM
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page
15.
Note: When you have completed an event, your
total time and the words “Cool Down” will appear
on the screen. If the speed of the walking belt was
greater than 5 mph when you completed the
event, the walking belt will then slow to 5 mph for
one minute. After one minute, the walking belt will
slow to 4 mph for 2 minutes. The walking belt will
then slow to 3 mph for 2 minutes. The walking belt
will then slow to a stop.
Select an event training program.
2
To select an event training program, press the
Event Training button repeatedly; the name of the
program and a track will appear on the screen.
Press the Start button to start the program.
3
A moment after the button is pressed, the walking
belt will begin to move at 3 mph. Hold the
handrails and begin walking.
Select a display mode and follow your
progress with the exercise information on the
screen.
4
Near the end of the second minute of the pro-
gram, the speed setting will flash on the screen
and a series of tones will sound. The speed of the
walking belt will then increase to 4 mph.
See step 5 on page 16.
Measure your heart rate if desired.
See step 6 on page 16.
5
6
7
Near the end of the third minute of the program,
the speed setting will flash on the screen and a
series of tones will sound. The speed of the walk-
ing belt will then increase to 5 mph.
Turn on the fan if desired.
See step 7 on page 16.
Near the end of the fourth minute of the program,
the speed setting will flash on the screen and a
series of tones will sound. The speed of the walk-
ing belt will then increase to 6.5 mph.
When you are finished exercising, remove the
key from the console.
See step 8 on page 16.
Note: To change the speed of the walking belt or
the incline of the treadmill at any time during the
program, press the Speed or Incline buttons.
During an event training program, the screen will
show the number of kilometers or miles still to be
run.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
If the speed and/or the incline of the treadmill is
about to change, the new speed setting and/or in-
cline setting will appear on the screen to alert you.
When the first
segment
ends, the
HOW TO USE A PRESET PROGRAM
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page 15.
arrow below
the program
diagram will
move one po-
sition to the
right. Note: The program diagram can be dis-
played only when the television is in Console
mode. To select the Console mode, press the TV
button repeatedly until the word “Console” ap-
pears on the screen.
Select a preset program.
2
To select a preset program, press the Aerobic
Fitness button, the Performance button, or the
Weight Loss button repeatedly.
When a pre-
set program
is selected,
the screen
will show the
maximum
speed setting
When the first segment ends, the treadmill will au-
tomatically adjust to the speed and incline settings
for the second segment.
and the maximum incline setting of the program,
and the workout time. In addition, a diagram of the
workout intensity settings of the program will be
displayed. The arrow below the diagram will indi-
cate your progress during your workout.
The program will continue in this way until the
arrow reaches the right end of the program dia-
gram. The walking belt will then slow to a stop.
If the speed and/or incline settings of the program
are too high or too low, you can override the set-
ting by pressing the Speed or Incline buttons;
however, when the next segment begins, the
treadmill will automatically adjust to the speed
and incline settings for the next segment.
Note: When a weight loss program is selected, the
screen will also show the calorie goal for the pro-
gram. Important: The calorie goal is an esti-
mate of the number of calories that you will
burn during the program. The actual number
of calories that you burn will depend on your
weight. In addition, if you manually change the
speed or incline of treadmill during the pro-
gram, the number of calories you burn will be
affected.
To stop the program at any time, press the Stop
button. To restart the program, press the Start but-
ton. The walking belt will begin to move at 1 mph.
When the next segment of the program begins, the
treadmill will automatically adjust to the speed and
incline settings for the next segment.
Enter your weight.
3
Select a display mode and follow your
progress with the exercise information on the
screen.
For the most accurate calorie count, enter your
weight by pressing the Rate/Wt. increase and de-
crease buttons repeatedly. Note: Once you have
entered your weight, it will be saved in memory.
5
See step 5 on page 16.
Press the Start button to start the program.
4
Measure your heart rate if desired.
See step 6 on page 16.
6
7
8
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Turn on the fan if desired.
See step 7 on page 16.
Each program is divided into several one-minute
segments. One speed setting and one incline set-
ting are programmed for each segment. Note: The
same speed and/or incline setting may be pro-
grammed for two or more consecutive segments.
When you are finished exercising, remove the
key from the console.
See step 8 on page 16.
When only three seconds remain in the first seg-
ment of the program, a series of tones will sound.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
When the first segment of the program ends, a se-
ries of tones will sound and the current speed set-
ting and the current incline setting will be saved in
memory. Program a speed setting and an incline
setting for the second segment as described
above.
HOW TO CREATE A CUSTOM PROGRAM
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page
15.
Continue programming speed and incline settings
for as many segments as desired; custom pro-
grams can have up to forty segments. When you
are finished with your workout, press the Stop but-
ton and then the Speed decrease button. The
speed and incline settings that you have pro-
grammed and the program time will then be saved
in memory.
Select one of the four custom programs.
2
To select a custom program, press the Custom
button repeatedly. When a custom program is se-
lected, the name of the program (CUSTOM: 1,
CUSTOM: 2, CUSTOM: 3, or CUSTOM: 4) will
appear on the screen.
Select a display mode and follow your
progress with the exercise information on the
screen.
Note: If the custom program has not yet been
designed, a workout time of three minutes will
appear on the screen. If the workout time is
more than three minutes, see HOW TO USE A
CUSTOM PROGRAM on page 20.
4
See step 5 on page 16.
Press the Start button and program the desired
speed and incline settings.
Measure your heart rate if desired.
See step 6 on page 16.
3
5
6
7
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
Turn on the fan if desired.
See step 7 on page 16.
Each custom program is divided into one-minute
segments. One speed setting and one incline set-
ting can be programmed for each segment. To
program a speed setting and an incline setting for
the first segment, simply adjust the speed and in-
cline of the treadmill as desired by pressing the
Speed and Incline buttons.
When you are finished exercising, remove the
key from the console.
See step 8 on page 16.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
press the Speed or Incline buttons. When the cur-
rent segment ends, the new setting will be saved in
memory. To increase the length of the program,
first wait until the program is completed. Then, press
the Start button and program speed and incline set-
tings for as many additional segments as desired.
When you have added as many segments as de-
sired, press the Stop and then the Speed de-
crease button. To decrease the length of the pro-
gram, press the Stop button and then the Speed de-
crease button at any time before the program is
completed.
HOW TO USE A CUSTOM PROGRAM
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page
15.
Select one of the four custom programs.
2
To select a custom program, press the Custom
button repeatedly. When a custom program is se-
lected, the name of the program (CUSTOM: 1,
CUSTOM: 2, CUSTOM: 3, or CUSTOM: 4) will
appear on the screen.
To stop the program temporarily, press the Stop
button. To restart the program, press the Start but-
ton. The walking belt will begin to move at 1 mph.
When the next segment of the program begins, the
treadmill will automatically adjust to the speed and
incline settings programmed for the next segment.
In addition, the maximum speed and incline set-
tings of the program, the workout time, and a pro-
file of the intensity settings of the program will ap-
pear. Note: If the workout time is only three
minutes, see HOW TO CREATE A CUSTOM
PROGRAM on page 19.
Select a display mode and follow your
progress with the exercise information on the
screen.
4
Press the Start button to start the program.
3
See step 5 on page 16.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings that you programmed previously.
Hold the handrails and begin walking.
Measure your heart rate if desired.
See step 6 on page 16.
5
6
7
Turn on the fan if desired.
See step 7 on page 16.
Each custom program is divided into several one-
minute segments. One speed setting and one in-
cline setting are programmed for each segment.
Note: The same speed setting and/or incline set-
ting may be programmed for two or more consec-
utive segments.
When you are finished exercising, remove the
key from the console.
The custom program will function in the same way
as a preset program (see step 4 on page 18).
See step 8 on page 16.
If desired, you can redesign the program while
using it. To change the speed setting or the in-
cline setting for the current segment, simply
20
Download from Www.Somanuals.com. All Manuals Search And Download.
will appear on the screen beside the words “Max
Target BPM.” If desired, press the Rate/Wt. in-
crease and decrease buttons to change the maxi-
mum target heart rate setting (see EXERCISE IN-
TENSITY on page 29). Note: If you change the
maximum target heart rate setting, the intensity
level of the entire program will change.
HOW TO USE A HEART RATE PROGRAM
CAUTION:
If you have heart prob-
lems, or if you are over 60 years of age and
have been inactive, do not use the heart rate
programs. If you are taking medication regu-
larly, consult your physician to find whether the
medication will affect your exercise heart rate.
Press the Start button to start the program.
5
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Follow the steps below to use a heart rate program.
Heart rate program 1 is divided into one-minute
segments. The same target heart rate setting is
programmed for all segments (except for the first
two segments). Heart rate programs 2, 3, and 4
are divided into 30 one-minute segments. One tar-
get heart rate setting is programmed for each seg-
ment. Note: The same target heart rate setting
may be programmed for two or more consecutive
segments.
Put on the chest pulse sensor.
1
Note: You must wear the chest pulse sensor to
use a heart rate program.
Insert the key into the console.
2
See HOW TO TURN ON THE POWER on page
15.
During each segment of the program, the console
will compare your heart rate to the target heart
rate setting for that segment. If your heart rate is
too far below or above the target heart rate set-
ting, the speed and/or incline will automatically in-
crease or decrease to bring your heart rate closer
to the target heart rate setting. Each time the
speed and/or incline of the treadmill is about to
change, the speed setting and/or incline setting
will flash on the screen to alert you, regardless of
which display mode is selected.
Select one of the four heart rate programs.
3
To select a heart rate program, press the Heart
Rate Control button repeatedly. When a heart rate
program is selected, the name of the program
(HEART RATE: 1, HEART RATE: 2, HEART
RATE: 3, or HEART RATE: 4) will appear on the
screen.
If heart rate program 1 is selected, a track will
appear on the screen.
If heart rate program 2, 3, or 4 is selected, a
series of tones will sound when the first segment
of the program ends. The arrow below the pro-
gram diagram will then move one position to the
right. The program will continue in this way until
the arrow reaches the right end of the program di-
agram. The walking belt will then slow to a stop.
If heart rate program 2, 3, or 4 is selected, a
profile of the heart rate settings of the program will
appear on the screen. The arrow below the profile
will indicate your progress during the workout.
Enter a target heart rate setting.
4
If heart rate program 1 is selected, the target
heart rate setting for the entire program will ap-
pear on the screen beside the words “Max Target
BPM” (beats per minute). If desired, press the
Rate/Wt. increase and decrease buttons to
change the target heart rate setting (see EXER-
CISE INTENSITY on page 29).
If the speed settings and/or incline settings are too
high or too low, you can change the intensity level
of the program at any time by pressing the Speed
and Incline buttons; however, when the console
compares your heart rate to the target heart rate
for the current segment, the speed and/or incline
of the treadmill may change to bring your heart
rate closer to the target heart rate setting.
If heart rate program 2, 3, or 4 is selected, the
maximum target heart rate setting of the program
21
Download from Www.Somanuals.com. All Manuals Search And Download.
To stop the program at any time, press the Stop
button. To restart the program, press the Start but-
ton. The walking belt will begin to move at 1 mph.
When the console compares your heart rate to the
target heart rate setting for the current segment of
the program, the speed and/or incline of the tread-
mill will automatically change to bring your heart
rate closer to the target heart rate setting.
source. If you do not wish to use the television,
select the Console mode.
Press the Channel buttons to select the
desired channel.
3
4
When the television is turned on, the screen will
show the last channel that was selected. To select
a different channel, press the Channel (CHAN)
buttons. The selected channel number will appear
on the screen for a few seconds. Note: The televi-
sion is equipped with a channel memorizing func-
tion that allows you to go directly from the current
channel to the next channel saved in memory.
Before channels can be selected in this way, they
must be saved in the television’s memory. See
HOW TO USE THE INFORMATION MODE on
page 23.
Select a display mode and follow your
progress with the exercise information on the
screen.
6
See step 5 on page 16.
Turn on the fan if desired.
See step 7 on page 16.
7
8
Press the Volume buttons to adjust the volume.
When you are finished exercising, remove the
key from the console.
When either Volume (VOL) button is pressed, the
volume level indicator will appear on the screen
for a few seconds.
See step 8 on page 16.
To use earphones or headphones (not included),
plug them into the headphone jack beside the key
on the console.
HOW TO OPERATE THE PERSONAL TELEVISION
IMPORTANT: Before operating the television, you
must connect an antenna, a 75 ohm CATV cable, or
a VCR to the 75 ohm antenna terminal on the tread-
mill; a VCR or DVD player to the three audio/video
RCA jacks; or a personal audio/video player to the
audio/video jack below the television on the con-
sole. See page 11 for instructions.
HOW TO USE THE STEREO SOUND SYSTEM
To play music or audio books through the console’s
stereo speakers, you must connect your MP3 player,
CD player, or personal audio/video player to the con-
sole. Locate the audio/video jack below the television
on the console, and plug it into a jack on your MP3
player, CD player, or personal audio/video player.
Make sure that the audio/video cable is fully
plugged in.
Follow the steps below to operate the television.
Insert the key into the console.
1
See HOW TO TURN ON THE POWER on page
15.
Next, select the MP3 source on the console by press-
ing the TV button repeatedly until “MP3” appears on
the screen.
Press the TV button to select a television
source or the Console mode.
2
Then, press the Play button on your MP3 player, CD
player, or personal audio/video player. Then, adjust
the volume on your MP3 player, CD player, or per-
sonal audio/video player. You can also adjust the vol-
ume on the console by pressing the Volume (VOL) in-
crease and decrease buttons.
Select a television source or the Console mode by
pressing the TV button repeatedly.
If you have connected an antenna, a 75 ohm
CATV cable, or a VCR to the 75 ohm antenna ter-
minal on the treadmill, select the Tuner source. If
you have plugged a DVD player or VCR into the
three audio/video RCA jacks, select the Input 1
source. If you have connected a personal
If you are using a personal CD player or DVD player
and the CD or DVD skips, set the CD player or DVD
player on the floor or another flat surface instead of on
the console.
audio/video player to the audio/video jack below
the television on the console, select the MP3
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Next, press the Channel (CHAN) buttons until the
contrast, color, sharpness, or hue level indicator ap-
pears. Adjust the settings, if desired, by pressing
the Volume buttons.
HOW TO USE THE INFORMATION MODE
The console features an information mode that allows
you to view treadmill usage information, select a sys-
tem of measurement for the console, and turn on and
turn off the demo mode. The information mode also al-
lows you to adjust the settings of the television and to
save channels into the television’s memory.
Press the TV button again and add or delete
channels.
3
After all valid channels available in your area have
been saved into the television’s memory (see step
5 on this page), you can manually add channels
or delete unwanted channels.
Follow the steps below to use the information mode.
Press the Rate/Wt. decrease button while in-
serting the key into the console.
1
To add or delete a channel, first press the
Channel buttons until the desired channel number
appears on the screen. Then, press the Volume
increase button to add the channel, or the Volume
decrease button to delete the channel. Continue
this process until you have added all desired
channels and deleted all unwanted channels.
When the information mode is selected, the lower
part of the screen will show the total number of
miles or kilometers that the walking belt has
moved (Distance) and the total number of hours
that the treadmill has been used (Time).
In addition, the center of the display will show the
word “English” for English miles or the word
“Metric” for metric kilometers. Press the Speed in-
crease button to change the unit of measurement if
desired.
Press the TV button again and select an
antenna connection or a cable connection.
4
After the TV button is pressed, press the Volume
decrease button to select the Antenna setting, the
Volume increase button to select the Standard
Cable setting, the Channel decrease button to se-
lect the Cable IRC setting, or the Channel in-
crease button to select the Cable HRC setting. If
you have connected an antenna to the treadmill,
the Antenna setting should be selected. If you
have connected a CATV cable, one of the three
Cable settings should be selected; try all three
Cable settings, if necessary, to find the optimal
setting.
IMPORTANT: If the words “Demo On” appear in
the center of the display, the “demo” mode is se-
lected. This mode is intended to be used only
when a treadmill is displayed in a store. When the
demo mode is selected, the power cord can be
plugged in, the key can be removed from the con-
sole, and the displays on the console will automati-
cally light in a preset sequence. The buttons on the
console will not function. If the words “Demo On”
appear on the screen when the information
mode is selected, press the Speed decrease
button so the words “Demo Off” appear.
Press the TV button again and save channels
into the television’s memory.
5
6
While the information mode is selected, you can
select an equalizer setting to optimize the sound
of your personal music if desired. To select an
equalizer setting, first press the Start/Stop button.
Next, press the Speed increase and decrease but-
tons to choose among Default, Classic, Country,
Techno, or Rock. When you have selected a set-
ting, remove the key from the console. Then,
press the Rate/Wt. decrease button while reinsert-
ing the key into the console.
When the TV button is pressed, the television will
begin scanning all of the channels available in
your area. When no broadcast signal is detected
on a channel, the channel will be skipped. When a
broadcast signal is detected, the channel will be
saved into memory and the next channel will be
selected. This process will continue until the high-
est channel is reached. Do not remove the key
while the television is scanning channels.
When you are finished using the information
mode, remove the key from the console.
Press the TV button and adjust the brightness,
contrast, color, sharpness, and/or hue of the
2
television.
To exit the information mode at any time (except
while the television is scanning channels), remove
the key from the console.
When the TV button is pressed, the brightness level
indicator will appear on the television screen. Press
the Volume (VOL) buttons to adjust the brightness
setting if desired.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ADJUST THE CUSHIONING SYSTEM
The treadmill features a cushioning system that re-
duces the impact as you walk or run on the treadmill.
To increase the firmness of the walking platform, step
off the treadmill and slide the platform cushions toward
the front of the treadmill. To decrease the firmness,
step off the treadmill and slide the platform cushions
toward the back of the treadmill. Note: Make sure that
both cushions are set at the same firmness level.
The faster you run on the treadmill, or the more you
weigh, the firmer the walking platform should be.
Platform
Cushion
Increase
Decrease
Platform
Cushion
Walking Platform
24
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If you do not do this, you may damage the
treadmill when you fold it. Remove the key and unplug the
power cord. CAUTION: You must be able to safely lift 45
lbs. (20 kg) to raise, lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by
the arrow at the right. CAUTION: To decrease the pos-
sibility of injury, do not lift the frame by the plastic foot
rails. To raise the frame, bend your legs, keep your
back straight, and lift with your legs. Raise the frame
about halfway to the vertical position.
Frame
2. Raise the frame until the latch knob locks into the storage
Frame
position. Make sure that the latch knob is locked in
the storage position.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of di-
rect sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° F (30° C).
Latch Knob
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the latch
knob is locked in the storage position.
1. Hold the handrails and place one foot against a wheel.
Handrails
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
Wheel
3. Place one foot against one of the wheels, and carefully
lower the treadmill until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand. Pull the latch knob to the left and hold it. Pivot the
frame downward and release the latch knob. Note: To release the latch knob, it may be necessary to push the
frame forward as you pull the latch knob to the left.
2. Hold the metal frame firmly with both hands, and lower it to the floor. CAUTION: To decrease the possibility
of injury, do not lower the frame by gripping only the plastic foot rails. Do not drop the frame to the floor.
Make sure to bend your legs and keep your back straight.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 13). Use only a single-outlet surge suppres-
sor that meets all of the specifications described on page 13. IMPORTANT: The treadmill is not
compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch pro-
trudes as shown, the circuit breaker has tripped. To
reset the circuit breaker, wait for five minutes and
then press the switch to the reset position.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch to the reset position.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
a
POWER CORD. Place the treadmill in the storage po-
sition (see HOW TO FOLD AND MOVE THE TREAD-
MILL on page 25).
Next, remove the two indicated 3/4" Screws (4).
4
4
Lower the treadmill (see HOW TO LOWER THE
4
4
TREADMILL FOR USE on page 25). Remove the four
indicated 3/4” Screws (4), and remove the Hood (44).
44
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Next, locate the Reed Switch (14) and the Magnet
(12) on the left side of the Pulley (11). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm). If neces-
sary, loosen the indicated Screw (29), move the Reed
Switch slightly, and then retighten the Screw. Then,
reattach the Hood (not shown). Place the treadmill in
the storage position. Reattach the four 3/4" Screws
(4) and lower the treadmill. Run the treadmill for a few
minutes to check for a correct speed reading.
Top
View
29
14
1/8 in.
11
12
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 13.
b. If the walking belt is overtightened, treadmill perfor-
b
3–4 in.
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 3 to 4 in. (8 to 10
cm) off the walking platform. Be careful to keep the
walking belt centered. Then, plug in the power cord,
Rear Roller Bolts
insert the key, and run the treadmill for a few min-
utes. Repeat until the belt is properly tightened.
c. If the walking belt still slows when walked on, please see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, remove the key and
UNPLUG THE POWER CORD. If the walking belt
has shifted to the left, use the hex key to turn the
left rear roller bolt clockwise 1/2 of a turn; if the walk-
ing belt has shifted to the right, turn the left rear
roller bolt counterclockwise 1/2 of a turn. Be careful
not to overtighten the walking belt. Plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is centered.
a
b. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the hex key, turn both rear roller bolts clockwise, 1/4
of a turn. When the walking belt is correctly tightened,
you should be able to lift each edge of the walking
belt 3 to 4 in. (8 to 10 cm) off the walking platform. Be
careful to keep the walking belt centered. Then, plug
in the power cord, insert the key, and carefully walk
on the treadmill for a few minutes. Repeat until the
belt is properly tightened.
b
PROBLEM: The console displays remain lit when you remove the key from the console
SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 22 to turn off the demo mode.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-
move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: Television reception is poor
SOLUTION: a. For the television to operate properly, good reception is necessary. If you are using an antenna,
make sure that it is properly connected and adjusted for optimal reception. (See HOW TO CON-
NECT AN ANTENNA on page 11.)
b. Check for the problems listed below and follow the applicable instructions.
• Ignition (black spots or horizontal streaks that appear or a picture that flutters or drifts)—Usually
this is caused by interference from automobile ignition systems, neon lamps, electric drifts, or
other electric appliances. Try changing the position of the treadmill or other electric appliances to
correct the problem.
• Ghosts—Ghosts are caused by the television signal following two paths—one is the direct path
and the other is reflected from tall buildings, hills, or other objects. Change the direction or posi-
tion of the antenna to improve reception.
• Blue Screen—If the treadmill is located in the fringe area of a television station where the signal is
weak, the picture may be of poor quality or a blue screen may appear. If the signal is weak, it may
be necessary to install an external antenna to improve the picture.
Note: If one of these symptoms appears when the cable from a CATV company is connected, the
symptom may be caused by the local company broadcast.
PROBLEM: The chest pulse sensor does not function properly
SOLUTION: a. If the chest pulse sensor does not function properly, see CHEST PULSE SENSOR TROU-
BLESHOOTING on page 12.
b. If the chest pulse sensor still does not function properly, the battery
b
should be changed. To replace the battery, locate the battery cover
on the back of the sensor unit. Insert a coin into the slot in the cover
and turn the cover counterclockwise to the “open” position. Remove
the cover.
Battery Cover
Remove the old battery from the sensor unit. Insert a new CR 2032
battery, making sure that the writing is on top. In addition, make sure
that the rubber gasket is in place in the sensor unit. Replace the bat-
tery cover and turn it to the closed position.
Battery
Cover
Battery
Rubber
Gasket
28
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exer-
cise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning any
exercise program, consult your physician.
This is especially important for persons over
the age of 35 or persons with pre-existing
health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is in-
tended only as an exercise aid in determining
heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic exer-
cise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic ex-
ercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper inten-
sity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 min-
utes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling down—Finish with 5 to 10 minutes of stretch-
ing. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the near-
est ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months of regular exer-
cise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. NTL19806.3
R1107A
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
2
2
16
62
9
1
2
4
2
2
1
1
13
1
2
2
2
2
2
1
1
1
1
1
1
1
1
1
9
2
1
2
4
1
1
1
1
11
1
1
1
2
1
1
4
2
1
1
1
Foot Rail Cover
Foot Rail
Cushion Track Screw
3/4" Screw
3/4" Tek Screw
Walking Platform
Belt Guide
Belt Guide Screw
Front Isolator
Platform Bolt, Front
Front Roller/Pulley
Magnet
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
1
1
4
2
1
4
2
1
1
1
1
2
2
1
6
1
1
1
1
6
1
1
6
1
1
1
1
1
6
1
4
4
4
1
3
2
2
2
1
1
10
3
1
12
2
1
1
1
1
Transformer
Right Rear Foot
Rear Wheel
Rear Wheel Bolt
Right Rear Endcap
Bracket Star Washer
Rear Roller Adj. Bolt
Hex Key
Left Rear Foot
Left Rear Endcap
Rear Roller
Platform Nut
Platform Bolt, Rear
Console Fan
Handrail Bolt
Console Base
Console
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
1/2" Screw
Reed Switch Clip
Incline Rod Bushing
Lift Arm
Lift Pivot Bolt
Hood Mount
Lift Arm Spacer
Reed Switch
Idler Wheel Nut
Idler Wheel
Idler Wheel Bolt
Lift Motor Bolt, Bottom
Idler Arm Spacer
Idler Arm
TV Console
Jack Ground Wire
Electronics Screw
Pulse Receiver Cover
Console Wire Harness
Upright Bolt
Left Upright
Right Upright
Upright Wire Harness
Left Base Cover
Right Base Cover
Washer
Idler Wheel Washer
Console Crossbar Star Washer
Base Pad
1" Tek Screw
Base
Pulse Bar Ground Screw
Wheel Bolt
Idler Arm Spring
Motor Belt
3/4" Tek Screw
Lift Pivot Bolt
Drive Motor
Motor Bolt
Electronic Bracket Nut
Electronic Bracket
Front Endcap
Controller
Incline Rod
Nut
Lift Motor
Lift Motor Bolt, Top
AV Cover
Platform Cushion
Power Cord Assembly
Hood
Hood Clip
Grommet
Walking Belt
Frame
TV Cable
Wheel
Caution Decal
Reset/off Circuit Breaker
Key/Clip
Star Washer
Releasable Tie
Tie Clamp
Plastic Tie
Handrail Cover
Left Upright Sleeve
Right Upright Sleeve
AV Wire
Ground Nut
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
99
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
4
1
2
1
1
1
Handrail
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
*
1
1
2
1
1
1
4
1
2
1
1
1
1
4
1
2
–
–
Left Pulse Grip
Right Pulse Grip
4" Ground Wire
Console TV Cable
Speaker Cover
Speaker
Speaker Screw
Caution Decal, Base
Cushion Track
Chest Pulse Sensor
Chest Pulse Strap
Chest Pulse Receiver
Chest Pulse Receiver Screw
Console Clamp Screw
Motor Isolator
Motor Mount Bushing
8" Blue Wire, 2 F
User’s Manual
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
Latch Assembly
Latch Warning Decal
AV Wire Nut
Filter Wire
Idler Arm Bolt
Rear Roller Washer
Incline/Controller Wire
Incline Stop Bracket
Stop Bracket Spacer
Static Decal
Console Plate
TV Cable Nut
TV Cable Star Washer
Lower Latch Bolt
Handrail Cover Fastener
Audio/Video Wire Harness
Console Clamp
Upper Latch Bolt
Latch Knob
*
*These parts are not illustrated.
Specifications are subject to change without notice.
Latch Endcap
31
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. NTL19806.3
R1107A
To identify the parts shown on this
EXPLODED DRAWING, see the
PART LIST on pages 30 and 31.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. NTL19806.3
R1107A
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to pro-
vide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST near the end of this manual
and the EXPLODED DRAWING in the center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The frame is warranted for a lifetime. The drive motor
is warranted for twenty (20) years after the date of purchase. Parts and labor are warranted for one (1)
year after the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All re-
pairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customer’s responsibility. This
warranty does not extend to any product or damage to a product caused by or attributable to freight
damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized
service center; products used for commercial or rental purposes; or products used as store display mod-
els. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-
cidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 261898 R1107A
Printed in USA © 2007 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|