Model No. NTL10940
Serial No.
USER'S MANUAL
Find the serial number in the location
shown below. Write the serial number
in the space above for reference.
Serial Number Decal
QUESTIONS?
If you have questions, or if there
are missing parts, we will guar-
antee complete satisfaction
through direct assistance from
our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
Customer Hot Line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-888-825-2588
Mon.–Fri., 6 a.m.–6 p.m. MST
Patent Pending
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
12. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed or stop unexpectedly, which may result
in a fall and serious injury.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
13. Keep the power cord and the surge suppres-
sor away from heated surfaces.
protect the floor or carpet from damage, place 14. Never move the walking belt while the power
a mat under the treadmill.
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See
BEFORE YOU BEGIN on page 5 if the tread-
mill is not working properly.)
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
15. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
7. The treadmill should not be used by persons
weighing more than 250 pounds.
17. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
8. Never allow more than one person on the
treadmill at a time.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
18. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord and move the reset/off circuit
breaker to the off position when the treadmill
is not in use. (See the drawing on page 5 for
the location of the reset/off circuit breaker.)
10. When connecting the power cord (see page 9),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 23.) You
must be able to safely lift 45 pounds (20 kg) to
raise, lower, or move the treadmill.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 9. To purchase a surge suppressor, see
your local NordicTrack dealer or call 1-800-
806-3651 and order part number 146148.
20. Do not change the incline of the treadmill by
placing objects under the treadmill.
21. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
22. When using iFIT.com CDs and videos, an
electronic “chirping” sound will alert you
when the speed and/or incline of the treadmill
is about to change. Always listen for the
“chirp” and be prepared for speed and/or in-
cline changes. In some instances, the speed
and/or incline may change before the per-
sonal trainer describes the change.
26. Never insert or drop any object into any
opening.
27.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the main-
tenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service
representative only.
23. When using iFIT.com CDs and videos, you
can manually override the speed and incline
settings by pressing the speed and incline
buttons. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the CD or video program.
28. The treadmill is intended for in-home use
only. Do not use the treadmill in any commer-
cial, rental, or institutional setting.
24. Always remove iFIT.com CDs and videos from
your CD player or VCR when you are not
using them.
29. Keep the aromatherapy bottle out of the reach
of children. Essential oil may irritate skin and
is not intended for internal or topical use.
25. Inspect and properly tighten all parts of the
treadmill regularly.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown have been placed on your treadmill and on the aromatherapy bot-
tle. If a decal is missing or illegible, please call our Customer Service Department,
toll-free, to order a free replacement decal (see ORDERING REPLACEMENT PARTS
on page 31). Apply the decal in the location shown. Note: The decals may not be
shown at actual size.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the revolutionary NordicTrack®
C1900 treadmill. The C1900 treadmill combines ad-
vanced technology with innovative design to help you
get the most from your exercise program in the conve-
nience of your home. And when you’re not exercising,
the unique C1900 treadmill can be folded up, requiring
less than half the floor space of other treadmills.
at 1-888-825-2588, Monday through Friday, 6 a.m.
until 6 p.m. Mountain Time (excluding holidays). To
help us assist you, please note the product model
number and serial number before calling. The model
number of the treadmill is NTL10940. The serial num-
ber can be found on a decal attached to the treadmill
(see the front cover of this manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our Customer Service Department toll-free
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Book Holder
Aromatherapy
Bottle Holder
Water Bottle Holder*
Console
Fan
Handrail
Pulse Sensor
Key/Clip
Latch Knob
RIGHT SIDE
Walking Belt
On/Off Circuit Breaker
Foot Rail
Power Cord
Cushion Deck
Rear Roller
Adjustment Bolts
*No water bottle is included.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own phillips screwdriver
and wire cutters
.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
For help identifying the assembly hardware, refer to the PART IDENTIFICATION CHART below.
4 1/2” Bolt (78)–4
Handrail Bushing
(77)–4
4” Bolt (53)–2
1” Tek Screw (47)–4
1. With the help of a second person, carefully raise the
1
Uprights (69) to the position shown.
See the inset drawing. Insert one of the Extension Legs
(102) into the treadmill as shown. Make sure that the
Extension Leg is turned so the Base Pad (99) is be-
neath it. Note: It may be helpful to tip the Uprights (69)
forward as you insert the Extension Leg.
69
69
Insert the other Extension Leg (not shown) in the same
way.
102
99
2. Press the Latch Knob Sleeve (70) into the left Upright (69).
2
Remove the Latch Knob (68) from the Latch Pin (74).
Make sure that the Latch Pin Collar (72) and the Spring
(71) are on the Latch Pin. Insert the Latch Pin into the
Latch Knob Sleeve (70) and the left Upright (69). Press
the Latch Knob Spacer (35) onto the other side of the left
Upright, and then tighten the Latch Knob back onto the
Latch Pin.
69
68
35
70
71
72
74
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Cut the rubber band holding the Upright Wire Harness
(98). Have a second person hold the console assembly
near the Uprights (69). Connect the Upright Wire Harness
to the wires extending from the Console Base (81). The
connectors should slide together easily and snap into
place. If they do not, turn one connector and try again.
Insert the connectors and the Upright Wire Harness into
the right Upright, and then set the console assembly on
the Uprights. Be careful not to pinch the wires.
3
98
81
98
69
Console
Assembly
4. Insert a Handrail (118) into the right side of the console
assembly as shown; you may need to twist the Handrail
as you insert it. Next, insert two 4 1/2” Bolts (78) with
Handrail Bushings (77) into the right Upright (69) and the
Handrail. Be careful not to pinch the wires. Make sure
that the Handrail Bushings are flush against the right
Upright, with the thicker sides facing the center of the
treadmill, as shown in the inset drawing.
4
69
Thick
Side
77
Next, lift the console assembly and the Handrail (118)
slightly and align the 4 1/2” Bolts (78) with the holes in the
Handrail. Thread the Bolts into the Upright (69) and the
Handrail until the heads of the Bolts are against the
Upright. Do not tighten the Bolts yet.
118
77
78
Console
Assembly
Attach the other Handrail (not shown) in the same way.
Note: There are no wires on the left side.
5. With the help of a second person, carefully tip the
Uprights (69) down to the position shown. Make sure that
the Extension Legs (102) remain in the Uprights.
5
99
53
69
Attach each Extension Leg (102) with two 1” Tek Screws
(47) and a Base Pad (99) as shown. Note: Attach the
lower Screw (without the Base Pad) first. Next, align the
lower ends of the Handrails (118) with the holes in the
base of the Uprights (69). Attach each Handrail with a 4”
Bolt (53) as shown. Note: The Bolts must be at an
angle that matches the angle of the Handrails as
shown in the inset drawing.
99
47
99
99
53
102
53
99
47
118
102
With the help of a second person, carefully tip the
Uprights (69) back to the vertical position. See step 4.
Tighten the four 4 1/2” Bolts (78).
99
118
Note: A replacement Base Pad (99) may be included. Use
the Base Pad to replace any Base Pad that becomes worn.
6. Make sure that all parts are properly tightened before you use the treadmill. Keep the included allen
wrench in a secure place. The allen wrench is used to adjust the walking belt (see page 26). To protect the
floor or carpet from damage, place a mat under the treadmill.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
If you purchase the optional chest pulse sensor (see page 22), follow the steps below to install the re-
ceiver included with the chest pulse sensor.
1. Make sure that the power cord is unplugged. Remove
1
the indicated screws from the Console Back (88).
(Important: The screws may be different lengths;
make sure to remember the original location of each
screw.) Next, remove the Console Back.
82
88
Screws
2. Peel the paper off the pad on the bottom of the receiver
(A). Turn the receiver so the small cylinder is on the
side shown, and press the receiver into the Console
Base (81) in the indicated location.
2
A
Cylinder
81
3. Connect the included short jumper wire (B) to the wire on
the receiver (A). Connect the other end of the short
jumper wire to the PLS2 jack on the underside of the
Console (82). (Note: If there is already a wire in the PLS2
jack, unplug it.) Discard the other wires included with the
receiver. Use the included wire tie to secure the wires, if
needed.
3
PLS2
Jack
82
Make sure that no wires are pinched. See step 1.
Reattach the Console (82) with the screws. Important: If
the screws are not reattached in their original loca-
tions, the Console may be damaged.
B
A
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PERFORMANT LUBETM WALKING BELT
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. Such substances will deteriorate the walking
belt and cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local NordicTrack dealer or call 1-800-806-
3651 and order part number 146148.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated
for 120 volts AC and 15 amps. There must be a
monitoring light on the surge suppressor to indi-
cate whether it is functioning properly. Failure to
use a properly functioning surge suppressor could
result in damage to the control system of the
treadmill. If the control system is damaged, the
walking belt may change speed or stop unexpect-
edly, which may result in a fall and serious injury.
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
tric shock. This product is equipped with a cord having
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Program Display
Pulse
Sensor
Pulse
Sensor
Note: If there is a sheet of clear
plastic on the console, remove it.
Key
Clip
FEATURES OF THE CONSOLE
stereo, portable stereo, computer, or VCR and play
special iFIT.com CD and video programs (iFIT.com
CDs and videocassettes are available separately).
iFIT.com CD and video programs automatically control
the speed and incline of the treadmill as a personal
trainer coaches you through every step of your workout.
High-energy music provides added motivation. To pur-
chase iFIT.com CDs or videocassettes, call toll-
free 1-800-735-0768.
The advanced console offers an impressive array of
features to help you get the most from your exercise.
When the manual mode of the console is selected, the
speed and incline of the treadmill can be changed with
the touch of a button. As you exercise, the console will
provide continuous exercise feedback. You can even
measure your heart rate using the built-in pulse sensor.
Note: For information about an optional chest pulse
sensor, see page 22.
With the treadmill connected to your computer, you
cess programs directly from the internet. Additional op-
tions are soon to be available. See www.iFIT.com for
more information.
Four preset workout programs are also offered. Each
program automatically controls the speed and incline
of the treadmill as it guides you through an effective
workout. You can even create your own custom work-
out programs and store them in memory for future use.
To use the manual mode of the console, follow the
steps beginning on page 11. To use a preset program,
see page 13. To create and use a custom program,
see pages 15 and 16. To use an iFIT.com CD or
video program, see page 19. To use an iFIT.com
program directly from our Web site, see page 21.
The console also features new iFIT.com interactive
technology. Having iFIT.com technology is like having a
personal trainer in your home. Using the included audio
cable, you can connect the treadmill to your home
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE MANUAL MODE
CAUTION:
Before operating the
console, read the following precautions.
Insert the key fully into the console.
1
• Do not stand on the walking belt when turn-
ing on the power.
See HOW TO TURN ON THE POWER at the left.
• Always wear the clip (see page 10) while op-
erating the treadmill.
Select the manual mode.
2
When the key is
inserted, the man-
ual mode will be
• Adjust the speed in small increments to
avoid sudden jumps in speed.
selected. If a pro-
gram has been se-
lected, reselect the
manual mode by
pressing the Select Program button repeatedly
until the track appears in the program display but
the indicator above the iFIT.com button is not lit.
• The pulse sensor is not a medical device.
Various factors, including the user’s move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console and place only a sealed water
bottle in the water bottle holder.
Start the walking belt.
3
To start the walking belt, press the Start button,
the Speed + button, or one of the ten Quick Start
buttons.
If the Start button or the
Speed + button is
HOW TO TURN ON THE POWER
pressed, the walking belt
will begin to move at 1
mph. As you exercise,
Plug in the power cord.
1
change the speed of the
See page 9.
walking belt as desired by pressing the Speed +
and – buttons. Each time a button is pressed, the
speed setting will change by 0.1 mph; if a button
is held down, the speed setting will change in in-
crements of 0.5 mph.
Move the reset/off circuit breaker to the reset
position.
2
Locate the reset/off cir-
cuit breaker near the
Reset
If one of the Quick Start buttons is pressed, the
walking belt will gradually increase in speed until it
reaches the selected speed setting. Note: The
console can display speed and distance in ei-
ther miles or kilometers. For simplicity, all in-
structions in this section refer to miles.
power cord. Make sure
Position
that the circuit breaker
is in the reset position.
Attach the clip to the waistband of your clothes.
3
Stand on the foot rails of the treadmill. Find the clip
attached to the key (see the drawing on page 10),
and slide the clip onto the waistband of your
clothes. Next, insert the key into the console. Test
the clip by carefully taking a few steps back-
ward until the key is pulled from the console. If
the key is not pulled from the console, adjust
the position of the clip as needed. Then, re-
move the key from the console.
To stop the walking belt, press the Stop button.
The time will begin to flash in the Time/Pace dis-
play. To restart the walking belt, press the Start
button, the Speed + button, or one of the ten
Quick Start buttons.
Note: During the first few minutes that the treadmill
is used, observe the alignment of the walking belt,
and align it if necessary (see page 26).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
segment of the program, and your current pace.
The display will change from one number to the
next every few seconds, as shown by the indica-
tors below the display.
Change the incline of the treadmill as desired.
4
5
To change the incline of
the treadmill, press the
Incline buttons. Each
time a button is
pressed, the incline will
Calories/Pulse
display—When the
handgrip pulse sensor is
not being used, this
display will show the ap-
proximate numbers of
calories and fat calories you have burned (see
FAT BURNING on page 27). When the handgrip
pulse sensor or the optional chest pulse sensor is
used, the display will also show your heart rate
(see step 6 below).
change by 0.5%. Note:
After the buttons are pressed, it may take a mo-
ment for the treadmill to reach the selected incline
setting.
Follow your progress with the displays.
The program
display—When
the manual mode
or the iFIT.com
mode is selected,
the program dis-
Speed display—This
display shows the speed
of the walking belt.
play will show a
track representing 1/4 mile. As you exercise, the
indicators around the track will light in succession
until the entire track is lit. The track will then
darken and the indicators will again begin to light
in succession.
Note: When the Km/H
indicator below the
Speed display is lit, the
console will display
speed and distance in
kilometers; when the in-
The Training Zone
display—As you exer-
dicator is not lit, the console will display speed
and distance in miles.To change the unit of mea-
surement, first hold down the Stop button while in-
serting the key into the console. An “E” for English
miles or an “M” for metric kilometers will appear in
the Speed display. Press the Speed + button to
change the unit of measurement. When the de-
sired unit of measurement is selected, remove the
key and then reinsert it.
cise, the Training Zone
display will show the
approximate intensity
level of your exercise.
For example, if three or four indicators are lit, your
intensity level is ideal for fat burning.
Incline/Distance
display—This display
shows the incline level
of the treadmill and the
distance that you have
To reset the displays, press the Stop button, re-
move the key, and then reinsert the key.
walked or run. The dis-
Measure your heart rate if desired.
play will change from one number to the other
every few seconds, as shown by the indicator
below the display. Note: Each time the incline
level changes, the display will show the incline
level.
6
To measure your
Metal Contacts
heart rate, stand
on the foot rails
and place your
hands on the metal
contacts on the
Time/Pace display—
When the manual mode
handrail. Your
or the iFIT.com mode is
palms must be rest-
ing on the upper
contacts, and your
fingers must be
touching the lower
contacts—avoid
selected, this display
will show the elapsed
time and your current
pace (pace is measured in minutes per mile).
When a preset program or a custom program is
selected, the display will show the time remaining
in the program, the time remaining in the current
12
Download from Www.Somanuals.com. All Manuals Search And Download.
moving your hands. When your pulse is detected,
the Pulse indicator will light, one or two dashes
(– –) will appear in the Calories/Pulse display, and
then your heart rate will be shown. For the most
accurate heart rate reading, continue to hold
the contacts for about 15 seconds.
HOW TO USE PRESET PROGRAMS
Insert the key fully into the console.
1
See HOW TO TURN ON THE POWER on page
11.
Turn on the fans if desired.
7
8
Select one of the four preset programs.
2
To turn on the fans at low speed, press the Fans
button. To turn on the fans at high speed, press
the Fans button a second time. To turn off the
fans, press the Fans buttons a third time. Note:
Any time that the walking belt is stopped for a few
minutes, the fans will automatically turn off.
When the key is
inserted, the man-
ual mode will be
selected. To select
a preset program,
press the Select
Program button re-
When you are finished exercising, stop the
walking belt and remove the key.
peatedly until the Runner’s Classic, Power Pace,
Champion Course, or Extreme Challenge indicator
lights.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest level.
The incline must be at the lowest level when
the treadmill is raised to the storage position or
the treadmill will be damaged. Next, remove the
key from the console and put it in a secure place.
Note: If the displays and indicators on the con-
sole remain lit after the key is removed, the
console is in the “demo” mode. See page 22
and turn off the demo mode.
For about six seconds after a program is selected,
the Incline/Distance display will flash the maxi-
mum incline setting for the program, and the
Speed display will flash the maximum speed set-
ting for the program. The Time/Pace display will
show how long the program will last. The program
display will show the first five speed settings of the
program.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the off position and
unplug the power cord.
Press the Start button or the Speed + button to
start the program.
3
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings for the program. Hold the handrails
and begin walking.
Each program is divided into several time seg-
ments of different lengths. (The Time/Pace display
will show both the time remaining in the program
and the time remaining in the current segment.)
One speed setting and one incline setting are pro-
grammed for each segment. (The same speed
setting and/or incline setting may be programmed
for two or more consecutive segments.) The
speed setting for the first segment will be shown in
the flashing Current Segment column of the pro-
gram display. (The incline settings are not shown
in the program dis-
play.) The speed
settings for the
Current Segment
next seven seg-
ments will be
shown in the
columns to the
right.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. In addition, if the speed
and/or incline of the treadmill is about to change,
the Speed display and/or the Incline/Distance dis-
play will flash to alert you. When the first segment
is completed, all speed settings will move one col-
umn to the left. The speed setting for the second
segment will then be shown in the flashing Current
Segment column and the treadmill will automati-
cally adjust to the speed and incline settings for
the second segment. Note: If all of the indicators in
the Current Segment column are lit after the speed
settings have moved to the left, the speed settings
will move downward so that only the highest indi-
cators appear in the program display. If some of
the indicators in the Current Segment column are
not lit when the speed settings move to the left
again, the speed settings will move back up.
To stop the program temporarily, press the Stop
button. The Time/Pace display will begin to flash.
To restart the program, press the Start button or
the Speed + button. The walking belt will begin to
move at 1 mph. When the next segment of the pro-
gram begins, the treadmill will automatically adjust
to the speed and incline settings for the next seg-
ment. To end the program, press the Stop button,
remove the key, and then reinsert the key.
Follow your progress with the displays.
See step 5 on page 12.
4
5
6
7
Measure your heart rate if desired.
See step 6 on page 12.
Turn on the fans if desired.
See step 7 on page 13.
The program will continue in this way until the
speed setting for the last segment is shown in the
Current Segment column and the last segment
ends. The walking belt will then slow to a stop.
When you are finished exercising, remove the
key.
Step onto the foot rails and make sure that the in-
cline of the treadmill is at the lowest level. The in-
cline must be at the lowest level when the
treadmill is raised to the storage position. Next,
remove the key from the console and put it in a se-
cure place. Note: If the displays and indicators
on the console remain lit after the key is re-
moved, the console is in the “demo” mode.
See page 22 and turn off the demo mode.
If the speed or incline setting is too high or too low
at any time during the program, you can manually
override the setting by pressing the Speed or
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will light or darken
in the Current Segment column. (If any of the
columns to the right of the Current Segment col-
umn have the same number of lit indicators as the
Current Segment column, an additional indicator
may light or darken in those columns as well.)
Note: If you manually override the speed or in-
cline setting, when the next segment begins,
the treadmill will automatically adjust to the
speed and incline settings for the next seg-
ment.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the off position and
unplug the power cord.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
setting and an incline setting for the first segment,
simply adjust the speed and incline of the tread-
mill as desired by pressing the Speed and Incline
buttons. Every few times a Speed button is
pressed, an additional indicator will light or darken
in the Current Segment column.
HOW TO CREATE CUSTOM PROGRAMS
Insert the key fully into the console.
1
See HOW TO TURN ON THE POWER on page
11.
During the last three seconds of the first segment,
both the Current Segment column and the column
to the right will flash, a series of tones will sound,
and the Speed display and the Incline/Distance
display will flash. When the first segment ends, the
current speed setting and the current incline set-
ting will be saved in memory, and all speed set-
tings in the program display will move one column
to the left. The speed setting for the second seg-
ment will then be shown in the flashing Current
Segment column. Program a speed setting and an
incline setting for the second segment as de-
scribed above.
Select one of the custom programs.
2
When the key is
inserted, the
manual mode will
be selected. To
select a custom
program, press
the Select
Program button repeatedly until the Learn 1 or
Learn 2 indicator lights.
Note: If the custom program has not yet been
defined, three columns of indicators will be lit
in the program display. If more than three
columns of indicators are lit, see HOW TO USE
CUSTOM PROGRAMS on page 16.
Continue programming speed and incline settings
for as many segments as desired; custom pro-
grams can have up to forty segments. When you
are finished with your workout, press the Stop but-
ton twice. The speed and incline settings that you
have programmed and the number of segments
that you have programmed will then be saved in
memory.
Press the Start button or the Speed + button
and program the desired speed and incline
settings.
3
Follow your progress with the displays.
See step 5 on page 12.
A moment after the button is pressed, the walking
belt will begin to move. Hold the handrails and
begin walking.
4
5
6
7
Measure your heart rate if desired.
See step 6 on page 12.
See the program display. Each custom program is
divided into one-minute segments. One speed
setting and one incline setting can be pro-
grammed for each segment. The speed setting for
the first segment will be shown in the flashing
Current Segment
Turn on the fans if desired.
See step 7 on page 13.
column of the
program display.
Current Segment
(The incline set-
tings are not
shown in the pro-
gram display.) To
program a speed
When you are finished exercising, remove the
key.
See step 7 on page 14.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
column and the column to the right will flash, a se-
ries of tones will sound, the Speed display and the
Incline/Distance display will flash, and all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
second speed and incline settings that you pro-
grammed previously.
HOW TO USE CUSTOM PROGRAMS
Insert the key fully into the console.
1
See HOW TO TURN ON THE POWER on page
11.
Select one of the custom programs.
2
The program will continue until the speed setting
for the last segment is shown in the Current
Segment column and the last segment ends. The
walking belt will then slow to a stop.
When the key is
inserted, the
manual mode will
be selected. To
select a custom
program, press
the Select
Program button repeatedly until the Learn 1 or
Learn 2 indicator lights.
If desired, you can redefine the program while
using it. To change the speed or incline setting
for the current segment, simply press the Speed
or Incline buttons. When the current segment ends,
the new setting will be saved in memory. To in-
crease the length of the program, first wait until
the program is completed. Then, press the Start but-
ton and program speed and incline settings for as
many additional segments as desired. When you
have added as many segments as desired, press
the Stop button twice. To decrease the length of
the program, press the Stop button twice at any
time before the program is completed.
For about six seconds after a program is selected,
the Incline/Distance display will flash the maxi-
mum incline setting for the program, and the
Speed display will flash the maximum speed set-
ting for the program. The Time/Pace display will
show how long the program will last. Note: If only
three columns of indicators are lit in the pro-
gram display, see HOW TO CREATE A CUS-
TOM PROGRAM on page 15.
To stop the program at any time, press the Stop
button. The time will begin to flash in the
Press the Start button or the Speed + button to
3
Time/Pace display. To restart the program, press
the Start button or the Speed + button. The walk-
ing belt will begin to move at 1 mph. When the next
segment of the program begins, the treadmill will
automatically adjust to the speed and incline set-
tings for the next segment.
start the program.
A moment after the button is pressed, the tread-
mill will automatically adjust to the first speed and
incline settings that you programmed previously.
Hold the handrails and begin walking.
Follow your progress with the displays.
See step 5 on page 12.
Each program is
4
5
6
7
Current Segment
divided into sev-
eral one-minute
segments. One
speed setting
and one incline
setting are pro-
grammed for
each segment. The speed setting for the first seg-
ment is shown in the flashing Current Segment
column of the program display. (The incline set-
tings are not shown in the program display.) The
speed settings for the next seven segments will be
shown in the columns to the right.
Measure your heart rate if desired.
See step 6 on page 12.
Turn on the fan if desired.
See step 7 on page 13.
When you are finished exercising, remove the
key from the console.
When only three seconds remain in the first seg-
ment of the program, both the Current Segment
See step 7 on page 14.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR PORTABLE STEREO
HOW TO CONNECT THE TREADMILL TO YOUR
CD PLAYER, VCR, OR COMPUTER
Note: If your stereo has an RCA-type AUDIO OUT
jack, see instruction A below. If your stereo has a
3.5mm LINE OUT jack, see instruction B. If your
stereo has only a PHONES jack, see instruction C.
To use iFIT.com CDs, the treadmill must be con-
nected to your portable CD player, portable stereo,
home stereo, or computer with CD player. See pages
17 and 18 for connecting instructions. To use iFIT.com
videocassettes, the treadmill must be connected to
your VCR. See page 19 for connecting instructions. To
use iFIT.com programs directly from our Web site,
the treadmill must be connected to your home com-
puter. See page 18 for connecting instructions.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter. Plug
the adapter into an AUDIO OUT jack on your stereo.
A
HOW TO CONNECT YOUR PORTABLE CD PLAYER
AUDIO OUT
RIGHT
LEFT
Note: If your CD player has separate LINE OUT and
PHONES jacks, see instruction A below. If your CD
player has only one jack, see instruction B.
Audio
Cable
Adapter
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your CD player. Plug your headphones into the
PHONES jack.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your stereo.
A
PHONES LINE OUT
LINE OUT
PHONES
B
Head-
phones
Audio
Cable
LINE OUT
Audio
Cable
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your CD player. Plug your
headphones into the other side of the Y-adapter.
C. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your stereo. Plug your
headphones into the other side of the Y-adapter.
B
PHONES
C
PHONES
3.5mm
Y-adapter
Audio
Cable
PHONES
3.5mm
Y-adapter
Audio
Cable
Headphones
Headphones
17
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR HOME STEREO
HOW TO CONNECT YOUR COMPUTER
Note: If your stereo has an unused LINE OUT jack,
see instruction A below. If the LINE OUT jack is
being used, see instruction B.
Note: If your computer has a 3.5mm LINE OUT jack,
see instruction A. If your computer has only a
PHONES jack, see instruction B.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the LINE OUT jack on your
stereo.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the LINE OUT jack on
your computer.
A
A
CD
LINE OUT
VCR
Amp
LINE OUT
Audio
Cable
LINE OUT
Audio
Cable
Adapter
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into a 3.5mm Y-adapter
(available at electronics stores). Plug the Y-adapter
into the PHONES jack on your computer. Plug your
headphones or speakers into the other side of the
Y-adapter.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the LINE OUT jack on your
stereo and plug the wire into the unused side of the
RCA Y-adapter. Plug the RCA Y-adapter into the
LINE OUT jack on your stereo.
B
PHONES
B
CD
Audio
Cable
3.5mm
Y-adapter
VCR
Amp
LINE OUT
Headphones/Speakers
RCA
Y-adapter
Audio
Adapter
Cable
Wire removed from
LINE OUT jack
18
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CONNECT YOUR VCR
HOW TO USE IFIT.COM CD AND VIDEO
PROGRAMS
Note: If your VCR has an unused AUDIO OUT jack,
see instruction A below. If the AUDIO OUT jack is
being used, see instruction B. If you have a TV
with a built-in VCR, see instruction B. If your VCR
is connected to your home stereo, see HOW TO
CONNECT YOUR HOME STEREO on page 18.
To use iFIT.com CDs or videocassettes, the treadmill
must be connected to your portable CD player, portable
stereo, home stereo, computer with CD player, or
VCR. See HOW TO CONNECT THE TREADMILL TO
YOUR CD PLAYER, VCR, OR COMPUTER on pages
17 to 19. Note: To purchase iFIT.com CDs or video-
cassettes, call toll-free 1-800-735-0768.
A. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into the AUDIO OUT jack on your
VCR.
Follow the steps below to use an iFIT.com CD or video
program.
A
Insert the key fully into the console.
ANT IN
.
VIDEO AUDIO
IN
RF OUT
1
CH
3
4
OUT
See HOW TO TURN ON THE POWER on page
11.
AUDIO OUT
RIGHT
LEFT
Select the iFIT.com mode.
Audio
Cable
2
Adapter
When the key is in-
serted, the manual
mode will be selected.
To use an iFIT.com CD
or video program, press
the iFIT.com button or
press the Select Program button repeatedly until
the indicator above the iFIT.com button lights.
B. Plug one end of the audio cable into the jack on the
front of the treadmill near the power cord. Plug the
other end of the cable into the included adapter.
Plug the adapter into an RCA Y-adapter (available
at electronics stores). Next, remove the wire that is
currently plugged into the AUDIO OUT jack on your
VCR and plug the wire into the unused side of the
RCA Y-adapter. Plug the RCA Y-adapter into the
AUDIO OUT jack on your VCR.
Insert the iFIT.com CD or videocassette.
3
If you are using an iFIT.com CD, insert the CD
into your CD player. If you are using an iFIT.com
videocassette, insert the videocassette into your
VCR.
B
Press the PLAY button on your CD player or
VCR.
ANT IN
.
VIDEO AUDIO
IN
RF OUT
CH
3
4
4
OUT
A moment after the button is pressed, your per-
sonal trainer will begin guiding you through your
workout. Simply follow your personal trainer’s
instructions. Note: If the Time/Pace display is
flashing, press the Start button or the Speed +
button on the console. The treadmill will not re-
spond to a CD or video program when the
Time/Pace display is flashing.
RCA Y-adapter
Adapter
Audio
Cable
Wire removed from
AUDIO OUT jack
During the CD or video program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes. In
some instances, the speed and/or incline may
change before the personal trainer describes
the change.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the CD or video program.
• Make sure that the audio cable is properly
connected, that it is fully plugged in, and that
it is not wrapped around a power cord.
• If you are using your portable CD player and
the CD skips, set the CD player on the floor or
another flat surface instead of on the console.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Pace dis-
play will begin to flash. To restart the program,
press the Start button or the Speed + button. After
a moment, the walking belt will begin to move at
1.0 mph. When the next “chirp” is heard, the
speed and incline will change to the next set-
tings of the CD or video program. When the CD
or video program is completed, the walking belt will
stop and the Time/Pace display will begin to flash.
Note: To use another CD or video program, press
the Stop button or remove the key and go to step
1 on page 19.
• See the instructions near the bottom of page
26.
Follow your progress with the displays.
See step 5 on page 12.
5
6
7
8
Measure your heart rate if desired.
See step 6 on page 12.
Turn on the fans if desired.
See step 7 on page 13.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard:
When the program has ended, remove the key.
See step 7 on page 14.
• Make sure that the iFIT.com indicator is lit and
that the Time/Pace display is not flashing. If
the Time/Pace display is flashing, press the
Start button or the Speed + button on the
console.
CAUTION: Always remove iFIT.com CDs and
videocassettes from your CD player or VCR
when you are finished using them.
• Adjust the volume of your CD player or VCR.
If the volume is too high or too low, the con-
sole may not detect the program signals.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Return to the treadmill and stand on the foot
rails. Find the clip attached to the key and slide
the clip onto the waistband of your clothes.
HOW TO USE PROGRAMS DIRECTLY FROM
OUR WEB SITE
7
When the on-screen countdown ends, the program
will begin and the walking belt will begin to move.
Hold the handrails, step onto the walking belt, and
begin walking. During the program, an electronic
“chirping” sound will alert you when the speed
and/or incline of the treadmill is about to change.
CAUTION: Always listen for the “chirp” and be
prepared for speed and/or incline changes.
basic programs, audio programs, and video programs
directly from the internet. Additional options are soon
To use programs from our Web site, the treadmill must
be connected to your home computer. See HOW TO
CONNECT YOUR COMPUTER on page 18. In
addition, you must have an internet connection and
an internet service provider. A list of specific system
requirements will be found on our Web site.
If the speed or incline settings are too high or too
low, you can manually override the settings at any
time by pressing the Speed or Incline buttons on
the console. However, when the next “chirp” is
heard, the speed and/or incline will change to
the next settings of the program.
Follow the steps below to use a program from our
Web site.
Insert the key fully into the console.
To stop the walking belt at any time, press the
Stop button on the console. The Time/Pace dis-
play will begin to flash. To restart the program,
press the Start button or the Speed + button. After
a moment, the walking belt will begin to move at
1.0 mph. When the next “chirp” is heard, the
speed and incline will change to the next set-
tings of the program.
1
See HOW TO TURN ON THE POWER on page
11.
Select the iFIT.com mode.
2
When the key is in-
serted, the manual
mode will be selected.
To use a program from
our Web site, press the
iFIT.com button or
press the Select Program button repeatedly until
the indicator above the iFIT.com button lights.
When the program is completed, the walking belt
will stop and the Time/Pace display will begin to
flash. Note: To use another program, press the
Stop button and go to step 5.
Note: If the speed or incline of the treadmill
does not change when a “chirp” is heard, make
sure that the iFIT.com indicator is lit and that
the Time/Pace display is not flashing. In addi-
tion, make sure that the audio cable is properly
connected, that it is fully plugged in, and that it
is not wrapped around a power cord.
Go to your computer and start an internet
connection.
3
Start your web browser, if necessary, and go to
4
Follow the desired links on our Web site to se-
lect a program.
Follow your progress with the displays.
See step 5 on page 12.
5
8
9
Read and follow the on-line instructions for using a
program.
When the program has ended, remove the key.
See step 7 on page 14.
Follow the on-line instructions to start the
program.
6
When you start the program, an on-screen count-
down will begin.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
THE INFORMATION MODE/DEMO MODE
HOW TO USE THE AROMATHERAPY SYSTEM
The console features an information mode that keeps
track of the total number of miles that the walking belt
has moved and the total number of hours that the
treadmill has been operated. The information mode
also allows you to switch the console from miles to
kilometers. In addition, the information mode allows
you to turn on and turn off the demo mode.
To make your
workouts more
enjoyable, the
console features
an aromatherapy
system. To use
NordicTrack®
Scent
Pad
REJUVENAIRE™
essential oils with
the console, press
the scent pads
into the recepticals beside the fans. Deposit a few
drops of essential oil onto each scent pad. As you exer-
cise, turn on the fans to circulate the essential oil
throughout your workout area. For information about
REJUVENAIRE scents and scent pads, call toll-free
1-800-215-7403.
To select the information mode, hold down the Stop
button while inserting the key into the console. When
the information mode is selected, the following informa-
tion will be shown:
The Incline/Distance
display will show the total
number of miles that the
walking belt has moved.
CAUTION: Keep the aromatherapy bottle out of the
reach of children. Essential oil may irritate skin
and is not intended for internal or topical use.
The Time/Pace display will
show the total number of
hours that the treadmill has
been used.
THE OPTIONAL CHEST PULSE SENSOR
An optional chest pulse sensor adds even more
features to the console. The chest pulse sensor provides
hands-free operation and continuously monitors your
heart rate during your workouts. To purchase the
optional chest pulse sensor, call toll-free 1-800-
734-2377.
An “E” for English miles or
an “M” for metric kilometers
will appear in the Speed/
Pace display. Press the
Speed + button to change
the unit of measurement.
IMPORTANT: The Calories/Pulse display should be
blank. If a “d” appears in the display, the console is in
the “demo” mode. This mode is intended to be used
only when a treadmill is displayed in a store. When the
console is in the demo mode, the power cord can be
plugged in, the key can be removed from the console,
and the displays and indicators on the console will au-
tomatically light in a preset sequence, although the
buttons on the console will not operate. If a “d” appears
in the Calories/Pulse display when the information
mode is selected, press the Speed – button so the
display is blank.
To exit the information mode, remove the key from the
console.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be per-
manently damaged. Remove the key and unplug the power
cord. CAUTION: You must be able to safely lift 45 pounds
(20 kg) to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. CAUTION: To decrease the possibility of in-
jury, bend your legs and keep your back straight. As
you raise the treadmill, make sure to lift with your legs
rather than your back. Raise the treadmill about halfway
to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the treadmill until the latch pin is
aligned with the indicated hole in the side of the treadmill.
Insert the latch pin into the hole. Make sure that the
latch pin is fully inserted into the hole.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° Fahrenheit.
Knob
Hole
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the latch
pin is fully inserted into the hole in the side of the tread-
mill.
1. Hold the handrails as shown and place one foot against a
wheel.
2. Tilt the treadmill back until it rolls freely on the front wheels.
Carefully move the treadmill to the desired location. Never
move the treadmill without tipping it back. To reduce
the risk of injury, use extreme caution while moving
the treadmill. Do not attempt to move the treadmill
over an uneven surface.
Base
3. Place one foot on wheel, and carefully lower the treadmill
until it is resting in the storage position.
Front Wheels
23
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand as
shown. Using your left hand, pull the latch knob to the left
and hold it. Pivot the treadmill down until the frame is past
the pin on the latch knob.
Knob
Frame
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. To decrease the possibility of in-
jury, bend your legs and keep your back straight.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-
free at 1-888-825-2588, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 9). Use only a single-outlet surge suppressor
that meets all of the specifications described on page 9. Important: The treadmill is not compatible
with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has tripped.
To reset the circuit breaker, wait for five minutes
and then press the switch back in.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and unplug the
a
power cord. Carefully tip the treadmill down as shown
in drawing a. Remove the Front Belly Pan Screws (3)
and the Screws (83) from the hood. Make a note
which holes the Screws are removed from. Raise the
Uprights (69) and carefully remove the hood.
69
3
83
Locate the Reed Switch (10) and the Magnet (7) on
the left side of the Pulley (8). Turn the Pulley until the
Magnet is aligned with the Reed Switch. Make sure
that the gap between the Magnet and the Reed
Switch is about 1/8”. If necessary, loosen the Screw
(27) and move the Reed Switch slightly. Retighten the
Screw. Re-attach the hood, making sure the Screws
are returned to the same hole they were removed
from. Run the treadmill for a few minutes to check for
a correct speed reading.
1/8”
8
27
10
7
Top
View
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 9.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
3”–4”
come damaged. Remove the key and UNPLUG THE
POWER CORD. Using the allen wrench, turn both
rear roller adjustment bolts counterclockwise, 1/4 of a
turn. When the walking belt is properly tightened, you
should be able to lift each side of the walking belt 3 to
4 inches off the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, in-
sert the key and run the treadmill for a few minutes.
Repeat until the walking belt is properly tightened.
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, please call our Customer Service Department, toll-
free.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, remove the key and UN-
a
PLUG THE POWER CORD. If the walking belt has
shifted to the left, use the allen wrench to turn the left
rear roller bolt clockwise 1/2 of a turn; if the walking belt
has shifted to the right, turn the left rear roller bolt coun-
terclockwise 1/2 of a turn. Be careful not to overtighten the
walking belt. Plug in the power cord, insert the key and run
the treadmill for a few minutes. Repeat until the walking
belt is centered.
b. If the walking belt slips when walked on, first remove the
b
key and UNPLUG THE POWER CORD. Using the allen
wrench, turn both rear roller bolts clockwise, 1/4 of a turn.
When the walking belt is correctly tightened, you should
be able to lift each side of the walking belt 3 to 4 inches off
the walking platform. Be careful to keep the walking belt
centered. Plug in the power cord, insert the key and care-
fully walk on the treadmill for a few minutes. Repeat until
the walking belt is properly tightened.
PROBLEM: The incline of the treadmill does not change correctly or does not change when iFIT.com
CDs and videos are played
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-
move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
uses easily accessible carbohydrate calories for en-
ergy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the tread-
mill until your heart rate is near the lowest number in
your training zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for individu-
als over the age of 35 or individuals with pre-
existing health problems.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recom-
mended heart rates for fat burning and aerobic exercise.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up in-
creases your body temperature, heart rate and circula-
tion in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “train-
ing zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
A Cool-down—Finish each workout with 5 to 10 min-
utes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent post-ex-
ercise problems.
To measure your heart rate during exercise, use the
pulse sensor on the console. If your heart rate is too
high or too low, adjust the speed and incline of the
treadmill.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months, you may com-
plete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
27
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
1
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and
groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles ten-
dons, bend your back leg as well. Stretches: Calves, achilles ten-
dons and ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp
one foot with your other hand. Bring your heel as close to your but-
tocks as possible. Hold for 15 counts, then relax. Repeat 3 times for
each leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
5
28
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
29
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. NTL10940
R1003B
To locate the parts listed below, see the EXPLODED DRAWING attached in the center of this manual.
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
2
2
2
1
2
2
1
1
4
1
4
1
1
1
1
1
1
1
1
5
1
1
1
1
1
1
12
1
1
1
1
1
2
6
1
1
1
1
1
2
1
1
1
4
6
2
6
1
4
4
1
Foot Rail Insert
Foot Rail
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80*
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
1
2
4
2
2
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
2
4
4
2
1
1
1
8
1
1
1
1
1
1
25
2
5
2
2
2
1
1
1
6
6
1
2
Walking Platform
4” Bolt
Platform Bolt
Spring Pad
Front Belly Pan Screw
Left Foot Rail Cap
Frame Pivot Bolt
Frame Pivot Spacer
Magnet
Front Roller/Pulley
Frame Pivot Nut
Reed Switch/Sensor Wire
U-nut
Reed Switch Clip
Lift Frame
Walking Belt
Motor Assembly
Motor
Pulley/Flywheel/Fan
Motor Belt
Motor Pivot Nut
Motor Tension Nut
Incline Motor Bolt (Top)
Motor Pivot Bolt
Hood
Incline Motor Bolt (Lower)
Motor Tension Bolt
Hole Plug
Spring
Ground Wire
Rear Endcap (Right)
Rear Roller Adj. Bolt
Warning Decal
Allen Wrench
Rear Roller
Audio Wire
Catch
Left Fan Housing
Console Frame
Spring Pad Screw
Latch Knob
Upright
Latch Knob Sleeve
Spring
Latch Pin Collar
Pin Clip
Latch Pin
9
10
11
12
13
14
15*
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
Filter Wire
Pulse Grip
Handrail Bushing
4 1/2” Bolt
Upright Endcap
Latch Assembly
Console Base
Console
Screw
Key/Clip
iFIT.com Wire
Jack
Aromatherapy Kit
Console Back
Releaseable Tie
Console Screw
Cable Tie Clamp
8” Cable Tie
Lift Pivot Bolt
Wheel Bolt
Wheel
Rear Endcap (Left)
Grommet
Upright Wire Harness
Base Pad
3/4” Screw
Screw
Transformer
Controller
Electronics Plate
Motor Controller Wire
Front Roller Adj. Bolt
2” Screw
Roller Washer
Latch Knob Spacer
Incline Motor
Incline Motor Stop
Motor Belly Pan
Audio Wire Nut
Static Decal
Console Ground Wire
Power Cord
Reset/Off Circuit Breaker
Spring Bolt
Belt Guide Screw
Belt Guide
1” Tek Screw
Motor Star Washer
Platform Nut
Spring Nut
Right Foot Rail Cap
Motor Washer
Extension Leg
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
103
104
105
106*
107
108
109
110
111
112
113
114
115
116
117
118
2
2
1
1
2
1
1
1
1
2
2
1
1
1
1
2
Extension Cap
119
120
121
#
#
#
#
#
#
#
2
1
1
2
1
1
1
1
1
1
1
1
1
Handrail Foam
Left Rear Foot
Right Rear Foot
Thick Base Pad
14” Blue Wire, 2F
12” Blue Wire, 2F
4” Blue Wire, M/F
8” Blue Wire, 2F
8” Black Wire, M/F
12” Green Wire, 2 Ring
4” Green Wire, F/Ring
10” Red Wire, M/F
User's Manual
Incline Warning Decal
Right Foam Trim
Extension Leg Assembly
Fan
Book Holder
Power Cord Grommet
Frame
Left Rear Foam Trim
Roller Star Washer
Spring Plate
Left Front Foam Trim
Left Cup Holder
Right Cup Holder
Right Fan Housing
Handrail w/Foam
#
#
#
* Includes all parts shown in box
# These parts are not illustrated
ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-888-825-2588, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). When ordering parts, please be prepared to give
the following information:
• the MODEL NUMBER OF THE PRODUCT (NTL10940)
• the NAME OF THE PRODUCT (NordicTrack® C1900 treadmill)
• the SERIAL NUMBER OF THE PRODUCT (see the front cover of this manual)
• the KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the PART LIST on pages 30 and 31 and the
EXPLODED DRAWING attached in the center of this manual)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. NTL10940
R1003B
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. NTL10940
R1003B
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
WHAT IS COVERED—The entire NordicTrack® C1900 treadmill (“Product”) is warranted to be free of all defects in ma-
terial and workmanship.
WHO IS COVERED—The original purchaser or any person receiving the Product as a gift from the original purchaser.
HOW LONG IS IT COVERED—ICON Health & Fitness, Inc. (“ICON”), warrants the motor for three years after the date
of purchase. The belt and deck are covered for two years after the date of purchase. All mechanical components are
covered for two years after the date of purchase. All electrical components are covered for two years after the date of
purchase. Labor is covered for one year. The hood, covers, belly pan, and decals are covered for six months after the
date of purchase.
WHAT WE DO TO CORRECT COVERED DEFECTS—We will ship to you, without charge, any replacement part or
component, providing the repairs are authorized by ICON first and are performed by an ICON trained and authorized
service provider, or, at our option, we will replace the Product.
WHAT IS NOT COVERED—Any failures or damage caused by unauthorized service, misuse, accident, negligence, im-
proper assembly or installation, alterations, modifications without our written authorization or by failure on your part to
use, operate, and maintain as set out in your User’s Manual (“Manual”). This warranty does not extend to products used
for commercial or rental purposes or to products used as store display modules.
WHAT YOU MUST DO—Always retain proof of purchase, such as your bill of sale; store, operate, and maintain the
Product as specified in the Manual; notify our Customer Service Department of any defect within 10 days after discov-
ery of the defect; as instructed, return any defected part for replacement or, if necessary, the entire product, for repair.
USER’S MANUAL—It is VERY IMPORTANT THAT YOU READ THE MANUAL before operating the Product.
Remember to do the periodic maintenance requirements specified in the Manual to assure proper operation and your
continued satisfaction.
HOW TO GET PARTS AND SERVICE—Simply call our Customer Service Department at 1-888-825-2588 and tell them
your name and address and the serial number of your Product. They will tell you how to get a part replaced, or if neces-
sary, arrange for service where your Product is located or advise you how to ship the Product for service. Before ship-
ping, always obtain a Return Authorization Number (RA No.) from our Customer Service Department; securely pack
your Product (save the original shipping carton if possible); put the RA No. on the outside of the carton and insure the
product. Include a letter explaining the product or problem and a copy of your proof of purchase if you believe the ser-
vice is covered by warranty.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the
use or performance of the product or damages with respect to any economic loss, loss of property, loss of revenues or
profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature.
Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above lim-
itation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability
or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not
allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
No one is authorized to change, modify or extend the terms of this limited warranty.
This warranty gives you specific legal rights and you may have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 203254 R1003B
Printed in USA © 2003 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|