02 ENG
IMPORTANT SAFETY INSTRUCTIONS
N O TICES:
1. Fully charge the Ni-MH battery before using it for the first time or reusing it after
being stored for a long period. It would need 3 to 5 circles of charging and
discharging operations to get the optimum performance of the battery.
2. The surrounding temperature has much to do with the charging efficiency and
O
O
should be between 0 C and 40 C. The charging performance will be in the most
O
O
efficient state from 10 C to 30 C.
3. It is suggested to carry out the actions of charging and discharging the battery
at least every one or two months if the battery is stored for a long time. Fully
recharge it again to be stored. This action can avoid the leakage or the bad
performance of the battery for its self-discharging action.
MOBILE ENTERTAINMENT
CONTENTS
ENG 03
DTV MENU
IMPORTANT SAFETY
INSTRUCTIONS
GENERAL STEPS OF SETUP...............17
IMPORTANT SAFETY
INSTRUCTIONS.......................................1
DTV CHANNEL
TV CHANNELS
PACKAGE CONTENTS
AND RADIO CHANNELS ......................
FAVORITE..............................................
18
18
PACKAGE CONTENTS .........................
4
DTV CONFIGURATION
PARTS IDENTIFICATION
SYSTEM SETTING................................
20
AUTO SCAN...........................................
MAIN UNIT...............................................
MAIN UNIT CONTROL SECTION...........
MAIN UNIT LEFT SIDE............................
5
5
6
25
MANUAL SCAN.....................................
25
MAIN UNIT RIGHT PANEL.......................
7
MAIN UNIT REAR SIDE...........................
8
GAME
8
HOW TO STAND......................................
REMOTE CONTROL...............................
KEY DESCRIPTION
BOXMAN................................................
9
26
BURNING TETRIS.................................
HIT RAT..................................................
26
27
OF REMOTE CONTROL........................
10
NOTES ON USING THE
REMOTE CONTROL UNIT......................
11
REPLACING THE BATTERY...................
11
FM INSTRUCTIONS
FM...........................................................
28
DTV PARTS IDENTIFICATION
SPECIAL KEYS......................................
12
OTHERS
DIMENSION AND PARAMETER............
30
USB PLAYBACK
OPERATIONS
TECHNICAL INFORMATION
USING THE USB PORT.........................
15
TROUBLE SHOOTING..........................
31
MOBILE ENTERTAINMENT
04 ENG
PACKAGE CONTENTS
P A CKAG E C O N TEN TS
After unpacking, first check that all the accessories listed below are included:
Access ory bag
AC / DC adapter
Audio a nd vi deo ca bles
MTVOD8E5L0NO.
OPERATING INSTRUCTIONS
Di
g
o
i
t
al
V
i
d
eo
B
r
a
d
c
a
s
t
i
ng
Carryin g bag
Operating manual
Remot e control
Car power cable
Car b ag
Mini-magnetic Antenna
NOTES:Actual products' appearance might vary slightly from the pictures shown.
MOBILE ENTERTAINMENT
PARTS IDENTIFICATION
ENG 05
M AI N U N IT
1
2
My
FM
3
4
1.Liquid crystal display
2.Speakers
3.Control section
Control buttons.
4.Remote control sensor
The remote control signals are received from here.
M AI N U N IT CO N TRO L SEC TIO N
MyFM
1.ADJUST button
Press it to enter the adjustment menu. Use the +/- button to choose the Picuture
/OSD/ FM/ EXIT items, then press the ADJUST button to enter you want .Then
use the +/- and ADJUST buttons to handle what you want to do.
1.Picture(
)
MOBILE ENTERTAINMENT
06 ENG
PARTS IDENTIFICATION
CONTRAST: Level 0 to 8.
BRIGHTNESS: Level 0 to 8.
SATURATION: Level 0 to 8.
SCREEN SIZE: Switch screen between
16:9 and 4:3.
Contrast
Brightness
Saturation
Screen Size
Display Mode : Normal
Exit
DISPLAY MODE: Switch screen between
normal and rotate.
.
ENT.
A
2.OSD (
)
OSD languages: English, French, German, Spanish and Italian.
OSD Timeout : Level 10 to 60.
Transparency: Level 0 to 7.
F
M
)
3.FM (
See the detail in page 28.
2.- / + button
In the menu state, they are used as down and up button. If not, they are used as
volume control button.
3. DVB button
In the AV IN/USB state, press it to enter DVB. In the DVB state, it is an invalid
button. Press it for 3 secords it will close the the TFT, then press any key can
open the TFT again.
4. MUTE(My FM) button
Press it to mute the audio press it again the mute is cancelled. If you hold it on for
3 seconds it will turn on the FM , then the second time you do the same thing it
will turn off the FM.
5.CH-/CH+ button
Press these two buttons respectively to channel down/up.
Press them simultaneously to go to the AUTO SCAN.
M AI N U N IT TO P P AN EL
3
4
1
2
1. MODE button
Press it to choose DVB/AV IN/ USB mode.
2. INFO button( ENTER )
Press it once to show the primary program information menu. Press it twice to
show the particular program information menu and then press it again to exit from
the interface.
It is only useful for the USB operation as the enter button.
MOBILE ENTERTAINMENT
PARTS IDENTIFICATION
ENG 07
3.EPG button(
)
Press it to show the electric program menu, press it again to exit from it.
It is only useful for the USB operation as the left button.
4.TTX button(
)
Press it to show the teletext information menu.
It is only useful for the USB operation as the right button.
M AI N U N IT LEFT P AN EL
1
2
3
4
5
6
1.EARPHONE jack
For connecting a stereo earphone or an amplifier.
2.USB jack
Support USB 1.1 use.
3.VIDEO IN/OUT jack
Input or output video signals to the connected device by setting AV IN/OUT mode
value.
The included AV cable is connected here.
4.AUDIO IN/OUT jack
Input or output audio signals to the connected device by setting the AV IN/OUT
mode value.
The included AV cable is connected here.
5.DC OUT
DC OUTPUT.
6. DC IN
Connect the included AC adapter here.
M AI N U N IT RI G HT PA N EL
3
1
2
MOBILE ENTERTAINMENT
08 ENG
PARTS IDENTIFICATION
1.POWER ON/OFF switch
Push the button to “ON” or “OFF” to turn on or turn off the power.
2.POWER indicator
The LED will be red when the unit is on.
3.ANTENNA Jack
DVB-T type aerial input.
M AI N U N IT REAR SI DE
1
1.Support
The unit can stand with this device.
H O W TO STAN D
1. Pull out the support.
2. Draw out the support to a proper position .
3. Push down the button to lock it.
U
N
L
O
C
K
UNLOCK
LO CK
L
O
C
K
MOBILE ENTERTAINMENT
PARTS IDENTIFICATION
ENG 09
REM O TE CO N TRO L
(10)
(11 )
(12)
(13)
(14)
(1)
(2)
(3)
(16)
(15)
(4)
(5)
(18)
(6)
(7)
(17)
(19)
(8)
(20)
(21)
(9)
(22)
(23)
(24)
(25)
(27)
(26)
MOBILE ENTERTAINMENT
10 ENG
PARTS IDENTIFICATION
KEY DESC RIP TIO N O F REM O TE CO N TR O L
14.VOL+
Volume up.
1. MENU
Press it to show the menu.
2. EXIT
Exit from the current item.
15.VOL-
Volume down.
3. CH+/UP
Press it to change channels up
or move the cursor up.
16.ENTER
Confirm the selection action.
17.L/R
Switch the audio channels.
4. FAV-
Switch to previous favorite
18.MUTE
Audio mute on/off.
program if you have setted some
programs as your favorite programs.
if not, it is invalid key.
19. MODE
Press it to pop out the play modes
selecting menu:DVB-T/ AV IN.
5. FAV+
Switch to next favorite
program if you have setted some
programs as your favorite programs.
If not, it is invalid key.
20.INFO
To display program information.
21.EPG
Electronic Program Guide.
6.P/N
Output the TV type.
22.TTX
Show the teletext information.
7. CH-/DOWN
Press it to change channels down
or move the cursor down.
23.-/--
Press this button to select channel
8. DIGITS
numbers of one figure or double digits.
Number keys.
24.
25.
27.
26.
9. Pre-CH
It is fast backward key when play the
USB files.(Invalid in DVB-T state)
Jump back to the previous
channel.
10.AUTO SCAN
Press it to play or pause playback of
USB files.(Invalid in DVB-T state).
Automatic search.
11.MANUAL SCAN
Manual search.
Press it to stop playback of USB files.
(Invalid in DVB-T state)
12.DTV/RADIO
Choose TV program or radio
program.
It is fast forward key when play the
USB files. (Invalid in DVB-T state)
13.AUDIO
Multi-track selection.
MOBILE ENTERTAINMENT
PARTS IDENTIFICATION
ENG 11
N O TES O N U SI N G THE REMO TE C O N TRO L U N I T
Do not drop or step on the remote control unit or subject it to shocks.
Note that the remote control unit may not work if there are obstacles between
it and the remote sensor.
Do not expose the remote sensor to strong light. Doing so may make operation
impossible.
Use the remote control unit within the specified operating range.
REP LAC IN G TH E BATTERY
Insert your finger nails into A and
3.Fit the battery holder back to its
1.
place.
B on the diagram below. Press A
according to the direction, then
pull out the battery holder.
A
B
NOTE:
To prevent leakage of fluid from the
lithium battery, remove the battery
when not using the remote control unit
for long periods of time (One month or
more). If the battery leaks fluid,
carefully wipe it out of the battery
case, then change to a new lithium
battery.
Remove the old battery, then
insert the new battery into the
battery holder with the + side
facing upwards.
2.
Caution: The battery may present a
risk of fire if mistreated. Do not
recharge, disassemble, heat above
100 C. Replace battery with same
type.
CR2025
Dispose of used battery properly,
keep away from children and do not
dispose of in fire.
Lithium ba tte ry (CR2025)
MOBILE ENTERTAINMENT
12 ENG
DTV PARTS IDENTIFICATION
SPEC IAL KEYS
EPG (Electronic Program Guide)
A quick program guide that the user can easily move up/down to view the
brief description of the selected program.
Press the EXIT button or the EPG button again to exit from this interface.
Electronic Program Guide
Video
08/08/2005
13:00
14:00
15:00
A
B
C
Program List
Program
Description
If the current channel is scrambled, the prompt message "scrambled
channel." will appear on the screen.
Scrambled channel.
L/R
Press this button to change the audio channels at non-menu status.
Ste re o
Stereo
Le ft
Rig ht
MOBILE ENTERTAINMENT
DTV PARTS IDENTIFICATION
ENG 13
MANUAL SCAN
Perform program scanning. (Found programs will be appended to the program list.)
Manual Scan
Scan Type
Scan Type
Start Freq
End Freq
Singl e Scan
170000KHz
890000KHz
6MHz
Band Width
Start Scan
Press OK
Use FAV+/- to select or Press OK to view list
Press EXIT to return
Scan Complete
Channel
1
CH
Strength
Quality
0
0
Frequency
170000KHz
1/1
Progress
TV
:
0000
RA DIO
:
0000
No TV program
No radio program
Press OK to exit
Press EXIT to return
There are 4 items:
Scan Type: Range Scan and Single Scan.
Start Freq: Input the start frequency of your preferred scan range.
End Freq: Input the end frequency of your preferred scan range.
Band Width: 6MHz, 7MHz and 8MHz.
You can use
buttons to select the options with your actual need.
Press OK to start scanning.
NOTE:
If Single Scan is your selection, you cannot edit the End Freq but only the Start
Freq as the appointed scanning frequency.
MOBILE ENTERTAINMENT
14 ENG
DTV PARTS IDENTIFICATION
INFO
Press this button to bring forth the primary program information.
TV
0001
Signal
14:29:08
GD
88%
Stereo
Language 1/1
1
Press this button twice to bring forth the particular program information, and press it
again to exit from this interface .
Program Info
Prog Name
Prog NO .
Lock
Band Width
Hi erarc hy
GD
1
001 Frequency
NO
N/ A
N/ A
N/A
N/A
Modulation
Guard Interval N/A
HP Code Rate N/A
LP Code Rate N/A
Trans mission N/ A
Strength
Quality
90%
88%
AUDIO
Audio channel information displays.
Language 1/1
MOBILE ENTERTAINMENT
ENG 15
USB PLAYBACK OPERATIONS
U SIN G THE U SB PO RT
Only in the DTV status can it read the MP3, JPG, BMP and MPEG files stored in a
USB device which is plugged into the USB port on the left side of the unit.
1. If a USB device is connected before the unit is turned on, there will be a prompt
message shown on the screen, press the
and ENTER buttons on the remote
conrtrol or on the top panel of the main unit to select the media.
2. If the unit is playing TV when a USB device is connected, there will be a prompt
message shown on the screen for selecting the media.
DIGITAL
3. During the playback of MP3 and MPEG or at the stopping state of JPG and BMP
files ,the following picture will appear:
a
b
c
Mp3
MP3 ICON
a.
b.
C.
JPG and BMP ICON
MPEG ICON
MOBILE ENTERTAINMENT
16 ENG
USB PLAYBACK OPERATIONS
USE
keys to move the cursor to a folder, a file ,MP3 ICON,
JPEG ICON or MPEG ICON.
Press OK to enter the folder or play the file highlighted.
You can press
keys to rotate or flip the picture when you are viewing
the JPG or BMP files.
You can control the playback of USB files by pressing
keys.
4. If there is a USB device connected, you can enter the media selecting interface
by pressing the EXIT button during the playback of USB or TV.
NOTE:
1. The unit may not work properly if using USB connecting cable. Suggested
not to use it.
2. Support USB 1.1 .
3. The USB function cannot be available in AV IN state.
MOBILE ENTERTAINMENT
17
ENG
DTV MENU
GEN ERAL STEP S O F SETU P
1.Press the MENU key on the remote control to bring “main menu”.
There are three classifications: DTV Channel, Configuration and Game .
DTV Ch annel
TV Cha nnel s
Radio Cha nne ls
Pro gram Guide
USB
2.Press and buttons to highlight the icon of the desired page, then press the
Down or Up button to activate that page.
GAME
Bo xMan
Bu rnin g Tetris
Hit Rat
3.Press and buttons to highlight the desired option. Press OK to select.
GAME
Bo xMan
Bu rnin g Tetris
Hit Rat
4.You can press MENU or EXIT again to exit MENU.
MOBILE ENTERTAINMENT
18 ENG
DTV CHANNEL
19
TV CH A N N ELS AN D RADI O C HA N N ELS
There are two different kinds of channels: TV Channels and Radio Channels.
You can manage the current channels by labeling your favorites, deleting the
non-favorites, moving the program's order and locking the channels. The default
is FAVORITE.If there are no programs saved in the database when entering TV
"
"
Channels or Radio Channels, the prompt message “No TV channels. or No
radio channels.” will pop out and disappear within several seconds.
DTV Channel
TV Chann el s
Rad io Chan nel s
Progra m G uide
US B
FAVO R ITE
If you often watch some specific programs and wish to get to these programs
quickly, you can label these to be your favorites through the program
management actions. You can enter the FAVORITE interface by pressing the
MENU button on the remote control to enter the main menu,then press the “
”
button to choose the “TV channel ” item under he DTV channe,Press “ ”enter
button to enter the FAVORITE interface. Exit after finishing the favorite programs
selection action, you can use the remote control to select your favorite program
conveniently.
TV CHA NNELS
FAVORITE
001
A
002
003
B
C
Press OK to select
MOBILE ENTERTAINMENT
ENG 19
DTV CHANNEL
You can use and buttons to select any programs at FAVORITE management
status.
If the selected program is not labeled with the FAVORITE symbol, you can set it as
your favorite program by pressing the OK button and the FAVORITE symbol will
appear behind the program name.
If the selected program has already been labeled, press the OK button to cancel the
symbol.
You can set multi-program to be your favorites at the same time.
MOBILE ENTERTAINMENT
20 ENG
DTV CONFIGURATION
Choose “Configuration” item and you will see that there are three options for
selecting:
System Setting, Auto Scan and Manual Scan.
Config uration
Syst em Settin g
Auto Sca n
Ma nual Sca n
SYSTEM SETTIN G
Use and buttons to select your need. Then press OK key to bring forth all the
options for selecting.
OSD LANGUAGE
Seven available OSD languages:
Eng lish
De utsc h
Config uration
Esp a n o l
Syst em Settin g
Auto Sca n
Ma nual Sca n
OSD L ang uage
Screen Fo rma t
TV T ype
Eng lish
Deu ts ch
Fra nc a is
Espa nol
Sta rt Ch anne l
Set ScanArea
Acti ve An te nna
Password
Franca is
Portugu ^es
Italia no
Portug ue s
Ita lia n o
Ned er lands
Default
Ne d e rla nd s
The default is English.
SCREEN FORMAT
Choose the right screen format depending on your equipment. Three options for
choosing:
MOBILE ENTERTAINMENT
ENG 21
DTV CONFIGURATION
4:3 PS (Pa n & Sc a n)
4:3 LB(Le tte r Box)
16 :9 (Wid e Sc re e n)
Configuration
Syst em Se tting
Auto Sc an
Ma nual Sca n
OSD Lan guage
Screen Format
TV Type
Sta rt Channel
Set ScanArea
Active Antenna
Password
4: 3PS
4: 3LB
16:9
Default
NOTE:
If the screen format is incorrectly set, the images on the screen might
be distorted or clipped out. Therefore, adjust the screen format wisely
in order to get the perfect video display.
The default is 4:3PS.
TV Type
Select the TV type. (Auto means the output signal format will be changed
automatically according to the received signal.)
NTSC
Configuration
PAL
Syst em Se tting
Auto Sc an
OSD Lan guage
Screen Format
TV Type
Sta rt Channel
Set ScanArea
Active Antenna
Password
AUTO
Ma nual Sca n
NT SC
PAL
AU TO
Default
The default is AUTO.
Start Channel
If you want to watch the same channel each time the unit is turned on, you can
set the First Channel here.
Configuration
Syst em Se tting
Auto Sc an
Ma nual Sca n
OSD Lan guage
Screen Format
TV Type
Sta rt Channel
Set ScanArea
Active Antenna
Password
Default
MOBILE ENTERTAINMENT
22 ENG
DTV CONFIGURATION
After pressing OK in the Start Channel state, the following picture will appear:
Message Box
Enable/Disable
Start Channel Setting
YES
NO
Choose “YES” to show all the channels for selecting or “NO” to exit.
Choose Program
01
02
03
04
A
B
C
D
You have to select one of them to be the First Channel when the unit is turned
on. The default is NO.
The selection action will be saved and become effective when turning on the
unit next time.
The First Channel will be closed automatically if the selected channel is
deleted after the next scanning.
The First Channel will remain to be the same channel even when the First
Channel is moved.
If there is no selected First Channel, the last-playing channel will become the
First Channel when turning on the unit next time.
MOBILE ENTERTAINMENT
ENG 23
DTV CONFIGURATION
SET SCAN AREA
Select the proper region according to the place you are located. After setting,
press the AUTO SCAN key to scan the channels going on this region premise.
Ge rm a ny
Eng la n d
Ita ly
Fra nc e
Config uration
Spa in
Syst em Sett in g
Aut o Sca n
OSD L angu age
Sc re en Format
TV T ype
Start Cha nne l
Se t ScanArea
Ac tive An te nna
Pa ssword
Germany
Englan d
Italy
Holla n d
Ta iwa n
China
Ma nual Scan
France
Spain
Holland
Taiwan
Norwa y
Swe d e n
Finla n d
Portug a l
Othe rs
Default
ACTIVE ANTENNA
This funtion will help the unit get a better TV signal with the active antenna turned on.
Config uration
Syst em Sett in g
Aut o Sca n
Ma nual Scan
OSD L angu age
Sc re en Format
TV T ype
Start Cha nne l
Se t ScanArea
Ac tive An te nna
Pa ssword
ON
OF F
Default
The default is ON.
PASSWORD
Renew your password here.
Config uration
Syst em Sett in g
Aut o Sca n
OSD L angu age
Sc re en Format
TV T ype
Ma nual Scan
Start Cha nne l
Se t ScanArea
Ac tive An te nna
Pa ssword
Default
MOBILE ENTERTAINMENT
24 ENG
DTV CONFIGURATION
1.Input your old password first.
Old password :
2.Enter the new password.
New password :
*
3.Confirm your new password.
Confi rm :
*
NOTE:
1. If the confirmed password differs from the new password, you have to reenter
them until the two are the same.
2. The default password is 0000.
DEFAULT
Resume the factory settings.
Configuration
OS D Lan guage
Screen F orm at
TV Type
System Se tting
Auto Scan
Manual Sca n
St art C hannel
Set Scan Area
Active Antenn a
Pass word
Defau lt
MOBILE ENTERTAINMENT
ENG 25
DTV CONFIGURATION
After pressing OK in the Default state, the following picture will appear:
Message Box
Reset to default!
OK
Cancel
NOTE:
The default settings action will resume all the factory settings, including the
deletion of all the saved programs.
A UTO SCAN
Auto scanning.
Scanning...
Channel
58
740000KHz
45/57
Strength
Quality
28
0
Frequency
Progress
TV
:
0000
RADIO
:
0000
Press STOP to stop scan
Press EXIT to stop and exit
NOTE:
Press STOP to stop scanning and EXIT button to exit.
M AN UA L SCAN
Please refer to Special Keys.(Page 13)
MOBILE ENTERTAINMENT
26 ENG
GAME
Get to the game function from the main menu. You will find three kinds of games
in DTV state.
GAME
BoxMan
Burn ing Tetri s
Hi t Rat
BO XMA N
Use
appointed place. Only one box can be moved at a time.
,
,
and
buttons to control the little man to move the boxes to the
STEP 0 00 L EV EL
1
Press the MENU key to replay the current game and the OK key to play the
higher level.
Press EXIT to quit at any time.
BURN IN G TETRI S
1. Use and to move Tetris left and right.
2. Press to shift the direction of the Tetris.
3. Press to accelerate the Tetris downwards.
MOBILE ENTERTAINMENT
ENG 27
GAME
L E VE L
1
S COR E 0 0 0 0
Press the MENU key to replay the current game and the OK key to pause/play
the higher level.
Press EXIT to quit at any time.
H IT RA T
Press 1,2,3,4,5,6,7,8,9 to hit the rat according to its corresponding directions of
where it appears on the screen.
Press EXIT to quit at any time.
SCORE 00 LEVEL 1
20
MOBILE ENTERTAINMENT
28 ENG
FM INSTRUCTIONS
FM
1.Press the "ADJUST" button to pop out the menu of adjustment, OSD and FM.
-
+
2. Use the
/
buttons on the main unit board or remote control to choose FM, then
press ADJUST enter button.
FM
87.6 MHZ
Exit
A
ENT.
3. Use the - / + buttons to choose“ON”, then press ADJUST enter button to enter
frequency input mode.
FM
Z
87.6 MH
Exit
A
4. There are two frequency input modes: one is to input numbers directly; the other is
to increase or decrease frequencies by the direction buttons. Press the +/ - buttons
to move right/left to choose the number inputted place and press the ADJUST
button to confirm . Then press the +/- button to increase /decrease the frequency
number and press the ADJUST button to confirm the inputted number number.
FM
87.6 - 107.9 MHZ
087.6 MHZ
Exit
ENT.
A
MOBILE ENTERTAINMENT
ENG 29
FM INSTRUCTIONS
5. The input frequency range is from 87.6-107.9MHZ. The default is OFF.
6. If the input frequency is bigger than the maximum frequency it will output with the
107.9MHZ frequency. If the input frequency is smaller than the minimum frequency
it will output with the 87.6 MHZ frequency.
7. Press ADJUST button to save the choice after selecting the preferable frequency
within the permissible range. Then the player will transmit audio signal according
to this frequency. Choose “OFF” to turn off the FM function.
8. Adjust your receiving set (eg. car stereo) to the corresponding frequency to
receive the transmitted audio signal from the player.
9. The transmission range will be within approximately 3 meters.
MOBILE ENTERTAINMENT
ENG 31
TECHNICAL INFORMATION
TRO U BLE SH O O TI N G
Phenomenon
Solution
1. Check that the unit has been turned on, and that the
volume wheel is turned up.
2. Please scan channels before watching.
3. Check antenna is connected and working OK.
4. Check setup for correct TV regional setting system.
No sound
1. Check that the unit has been turned on.
2. Please scan channels before watching.
3. Check antenna is connected and working OK.
No picture
1. This phenomenon may appear when playing with the
low-capacity battery.
Sounds only
with no picture
2. Please recharge the battery fully to be played once
again.
1. This phenomenon may appear when using in a moving
vehicle.
2. Please replace the antenna to another place with a
stronger signal.
Bad image
3. Check that the settings of the TV system are right.
1. Position the volume setting of the unit to a suitable
level.
Low volume
No channel
can be
searched
1. The antenna may not be connected well.
2. Wrong regional setting .
3. Channels setting may be encrypted at your location.
DAMAGE REQUIRING SERVICE
Have the unit serviced by a qualified service technician if:
The unit has been exposed to rain or water.
The unit does not seem to operate normally.
The unit exhibits a marked change in performance.
DO NOT ATTEMPT TO SERVICE THE UNIT BY YOURSELF!
MOBILE ENTERTAINMENT
|